2007 Toyota Corolla Owners Manual

The indicator light comes on for a few seconds when the ignition key is turned to “ON”. In the following cases, contact your Toyota dealer: (cid:1) The indicator light does not come on when the ignition key is turned “ON”. (cid:1) The indicator light remains on after the

ignition is turned on.

(cid:1) The indicator light comes on with the

normal driving mode while driving.

that

NORMAL DRIVING MODE Leave the system on during the ordi- nary driving so it can operate when needed. You may hear a sound the engine compartment for a few seconds when the engine is started or just after the vehicle begins to move. This means that the trac- tion control system is in the self−check mode, but does not indicate a malfunction.

in

Traction control system The traction control system automatical- ly helps prevent the spinning of front wheels when the vehicle is started or accelerated on slippery road surfaces. When the ignition key is turned to “ON”, the system automatically turns on.

CAUTION

Under certain slippery road condi- tions, full traction of the vehicle and power against front wheels cannot be maintained, even though the traction control system is in operation. Do not drive the vehicle under any speed or maneuvering conditions which may cause traction control. In situations where the road surface is covered with ice or snow, your vehicle should be fitted with snow tire chains. Always drive at an appropriate and cautious speed the present road condi- tions.

the vehicle

tires or

lose

for

to

120

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

To turn on: Push “TRAC OFF” switch once again. The slip indicator light/traction control sys- tem off indicator light will go off. The indicator light comes on for a few seconds when the ignition key is turned to “ON”. It will come on again when you push the “TRAC OFF” switch to turn off the traction control system. In the following cases, contact your Toyota dealer: (cid:1) The indicator light does not come on when the ignition key is turned “ON”. (cid:1) The indicator light remains on after the

ignition is turned on.

(cid:1) The indicator light comes on with the

normal driving mode while driving.

“VSC” warning light This light warns that there is a problem somewhere in the traction control system or the vehicle stability control system. The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing.

121

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

TRACTION CONTROL OFF MODE When getting the vehicle out of mud or newly fallen snow, etc., turn off the traction control system. This system that controls engine performance inter- feres with the process of freeing front wheels. To turn off: Push “TRAC OFF” switch. The slip indicator light/traction control sys- tem off indicator light will come on. The vehicle stability control system is al- ways activated, even if the traction control system is turned off.

’07 Corolla_U (L/O 0608)

In the following cases, contact your Toyota dealer: (cid:1) The warning light does not come on after the ignition key is turned to “ON”. (cid:1) The warning light remains on after the

ignition key is turned to “ON”.

(cid:1) The warning light comes on while driv-

ing.

The slip indicator light/traction control sys- tem off indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed.

Vehicle stability control system The vehicle stability control system helps provide integrated control of the systems such as anti−lock brake sys- tem, traction control, engine control, etc. This system automatically controls the brakes and engine to help prevent the vehicle from skidding when corner- ing on a slippery road surface or oper- ating steering wheel abruptly. This system will activate when your ve- hicle speed reaches or exceeds 15 km/h (9 mph), and will deactivate when the ve- hicle speed reduces to below 15 km/h (9
mph). You may hear a sound the engine compartment for a few seconds when the engine is started or just after the vehicle begins to move. This means that the sys- tem is in the self−check mode, but does not indicate a malfunction.

in

CAUTION

(cid:1) Do not rely excessively on the ve- hicle stability control system. Even if the vehicle stability control sys- tem is operating, you must always drive carefully and attentively to avoid serious injury. Reckless driv- ing will result in an unexpected ac- cident. light flashes, an alarm sounds, and spe- cial care should be taken while driving.

indicator

the slip

If

(cid:1) Only use tires of specified size. The size, manufacture, brand and tread pattern for all 4 tires should be the same. If you use the tires other than specified, or different type or size, the vehicle stability control system may not function correctly. When replacing the tires or wheels, contact your Toyota dealer. (See “Checking and replacing tires” on page 261 in Section 7−2.)

(cid:1) In situations where the road surface is covered with ice or snow, your vehicle should be fitted with snow tires or tire chains.

122

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

In the following cases, contact your Toyota dealer: (cid:1) The indicator light does not come on when the ignition key is turned “ON”. (cid:1) The indicator light remains on after the

ignition is turned on.

(cid:1) The indicator light comes on with the

normal driving mode while driving.

If the vehicle is going to skid during driv- ing, the slip indicator light blinks and an alarm sounds intermittently. Special care should be taken while driving. The slip indicator light/traction control sys- tem off indicator light comes on for a few seconds when the ignition key is turned to “ON”. If you select the traction control off mode, the indicator light will come on again.

“VSC” warning light This light warns that there is a problem somewhere in the vehicle stability control system or the traction control system. The light will come on when the ignition key is turned to “ON” and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing.

123

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

In the following cases, contact your Toyota dealer: (cid:1) The warning light does not come on after the ignition key is turned to “ON”. (cid:1) The warning light remains on after the

ignition key is turned to “ON”.

(cid:1) The warning light comes on while driv-

ing.

The slip indicator light/traction control sys- tem off indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed.

low

Tire pressure warning system The tire pressure warning system is de- signed to provide warning when tire inflation pressure of any one of the tires is critically low while the vehicle is moving. The low tire pressure warn- ing light comes on to inform you that such tire pressure may hamper driving. This system is not designed to operate when the vehicle is stopped. Therefore, check the tire inflation pressure regularly. The recommended cold tire inflation pres- sure, tire size and the vehicle capacity weight are on the tire and loading informa- tion label. (For instructions, see “Checking tire in Section 7−2.) Installed tires should be of the specified size. They should be of the same size and construction. If tires other than the specified size are used, or if tires of dif- ferent sizes or constructions are mixed, the tire pressure warning system will not function properly.

inflation pressure” on page 259

LOW TIRE PRESSURE WARNING LIGHT This light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the tire pressure warning system is func- tioning properly. If the low tire pressure warning light comes on or blinks while driving, do the following.

124

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

If the warning light comes on: 1. Adjust the tire inflation pressure to the specified level as soon as pos- sible. (See “Tires” on page 284 in Section 8.)

the

the warning

light remains on after

2. Push the tire pressure warning sys- tem reset switch for a few seconds and make sure light goes off. the

the reset If switch has been pushed, have tire pressure warning system checked at your Toyota dealer. If you have a flat tire, replace it with the spare tire. For details, see “If you have a flat tire” on page 217 in Section 4. If the warning light blinks once every second: The low tire pressure warning system may be malfunctioning. Contact your Toyota dealer. If the warning light blinks once every three seconds: The tire pressure warning system needs to be initialized. Reset the system with the tire pressure warning system re- set switch. (To the system, see “TIRE PRESSURE WARNING SYSTEM RESET SWITCH”.)

reset

low

’07 Corolla_U (L/O 0608)

(cid:1) The loading is over the limit or imbal-

anced.

(cid:1) Initialization was not performed correct- ly after replacing or rotating tires or wheels.

(cid:1) The outside temperature is below 0(cid:2)C

(32(cid:2)F) or above 40(cid:2)C (104(cid:2)F).

CAUTION

When the tire pressure warning light comes on, observe the following in- structions: (cid:1) Adjust the tire inflation pressure to the specified level as soon as pos- sible.

(cid:1) Avoid abrupt steering wheel maneu- vering and braking. If the vehicle tires deteriorate, you could lose control of the steering wheel or the brakes, causing death or serious in- jury.

The tire pressure warning system does not function properly under certain cir- cumstances. In the following cases, the low tire pressure warning light may not come on even if the tire inflation pres- sure is low, or it may come on when the tire is actually normal. (cid:1) A compact spare tire, snow tires, or

inflation pressure

tire chains are used.

(cid:1) The tire inflation pressure is excessive- ly higher than specified, or tire inflation pressure suddenly drops due to burst- ing or other causes.

(cid:1) The vehicle

is driven on a slippery road surface such as rough or frozen roads.

(cid:1) The vehicle speed is less than 30 km/h (19 mph) or more than 100 km/h (62
mph), and the driving duration is less than 5 minutes.

(cid:1) The

tires differ

in

tread pattern or

manufacturer.

(cid:1) The tires are not the specified size. (cid:1) The tread wear is very different among

the installed tires.

(cid:1) Rapid

acceleration/deceleration

or

sharp turns is continued.

(cid:1) Towing a trailer.

125

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

tires

Note: The tire pressure monitoring system on your vehicle will warn you when one of your tires is significantly under−inflated and when some com- binations of your tires are significant- ly under−inflated. However, there are other combinations of significantly under−inflated for which your tire pressure monitoring system may not warn you. These other combina- tions are relatively common, account- ing the instances in which vehicles have sig- nificantly under−inflated tires. For ex- ample, your system may not warn you when both tires on the same side or on the same axle of your vehicle are significantly under−inflated. It is par- ticularly important, therefore, for you to check the tire pressure in all of your regularly and maintain proper pressure.

approximately

tires

half

for

TIRE PRESSURE WARNING SYSTEM RESET SWITCH The tire pressure warning system need to be initialized in the following condi- tions: (cid:1) When the low tire pressure warning light blinks once every three sec- onds

(cid:1) After replacing or rotating tires or

wheels

When initializing the system, the pres- ent tire condition is stored as a stan- dard.

To initialize the system, perform the fol- lowing: 1. Park the vehicle at a safe place and apply the parking brake. Stop the en- gine.

2. Adjust the pressure of all the installed tires to the specified level. (See “Tires” on page 284 in Section 8.)

3. Turn the ignition key to “ON”.

If the low tire pressure warning light comes on, push the reset switch for a few seconds and make sure the warn- ing light goes off.

4. Push and hold the reset switch until light

tire pressure warning

low

the blinks three times.

Initialization is completed after driving at the speeds of 30 km/h (19 mph) or over for more than one hour. If the following driving conditions are satisfied, initializa- tion will be completed in about one hour. (cid:1) The vehicle speed is between 50 km/h

(31 mph) and 100 km/h (62 mph).

(cid:1) The roads are dry, smooth and straight. (cid:1) The number of passengers is 1 or 2

(including driver).

126

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Parking brake

If the low tire pressure warning light does not blink when you push and hold the reset switch, have the low pressure warn- ing system checked at your Toyota dealer. When the warning light blinks once every three seconds while driving, you may be unable to reset the system. In this case, set the above procedure.

the system again according

to

Type A

Type B

127

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

When initializing the system, make sure the low tire pressure warning light blinks three times. If the warning light does not blink three times, initializing will be failed and the tire pressure warning system will not function properly. Do not push the reset switch without ad- justing the tire inflation pressure to the specified tire pressure warning light may not come on even if the tire pressure is low, or it may come on when the tire inflation pressure is actually normal. If you push the reset switch while the vehicle is moving, initialization is not per- formed.

level. Otherwise,

low

the

’07 Corolla_U (L/O 0608)

it while setting

When parking, firmly apply the parking brake to avoid inadvertent creeping. To set: Pull up the lever. For better hold- ing power, first depress the brake pedal and hold the parking brake. To release: Pull up the lever slightly (1), press the lock release button (2), and low- er (3). To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake.

CAUTION

Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.

Cruise control The cruise control is designed to main- tain a set cruising speed without requir- ing the driver to operate the accelera- tor. Cruising speed can be set to any speed above 40 km/h (25 mph). Within the limits of the engine’s capabili- ties, cruising speed can be maintained up or down grades. However, changes in ve- hicle speed may occur on steeper grades.

CAUTION

(cid:1) To help maintain maximum control of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow−covered) or winding roads.

If

(cid:1) Avoid vehicle speed increases when driving downhill. the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.

128

TURNING THE SYSTEM ON AND OFF To turn the cruise control on, press the “ON−OFF” button. The “CRUISE” indicator light on the instrument panel will come on to indicate that the cruise control is opera- tional. Pressing “ON−OFF” button again turns the system off. When the system is turned off, cruising speed must be reset when the cruise con- trol is turned on again.

the

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

CAUTION

To avoid accidentally engaging the cruise control, turn the system off when it is not in use. Make sure the “CRUISE” indicator light is off.

’07 Corolla_U (L/O 0608)

If you need acceleration—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the vehicle will return to the speed set prior to the acceleration.

CAUTION

For manual transmission: While driving with the cruise control on, do not shift to neutral without depressing the clutch pedal, as this may cause engine racing or overrev- ving.

CANCELLING THE CRUISE CONTROL The cruise control may be temporarily cancelled by the driver or by the system itself under certain circumstances. Tempo- rary cancellation allows the set cruising speed to remain in memory. The cruise control can be temporarily can- celled by doing the following: (cid:1) Pulling the lever in the “CANCEL” di-

rection and releasing it

(cid:1) Depressing the brake pedal (cid:1) Depressing

the clutch pedal (manual

transmission)

129

SETTING THE CRUISING SPEED On vehicles with automatic transmission, the transmission must be in “D” before you set the cruising speed. Bring your vehicle to the desired speed, push the lever down in the “− SET” direc- tion and release it. This sets the vehicle at that speed. If the speed is not satisfac- tory, tap the lever up for a faster speed, or tap it down for a slower speed. Each tap changes the set speed by 1.6 km/h (1.0 mph). You can now take your foot off the accelerator pedal.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

the

light

indicator

“CRUISE”

CRUISE CONTROL FAILURE WARNING If flashes when using the cruise control, press the “ON−OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system. (cid:1) The indicator light does not come on. (cid:1) The indicator light flashes again. (cid:1) The

light goes out after

indicator

it

comes on.

If this is the case, contact your Toyota dealer and have your vehicle inspected.

RESETTING TO A FASTER SPEED Push the lever up in the “+ RES” direction and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “− SET” direction. RESETTING TO A SLOWER SPEED Push the lever down in the “− SET” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. However, a faster way to reset is to de- press the brake pedal and then push the lever down in the “− SET” direction. On vehicles with automatic transmission, even if you turn off the overdrive switch, with the cruise control on, engine braking will not be applied because the cruise control is not cancelled. To decrease the vehicle speed, reset to a slower speed with the cruise control lever or depress the brake pedal. the brake pedal, cruise control is cancelled.

If you use

Under certain circumstances, control is temporarily cancelled: (cid:1) When vehicle speed

falls below 40

the cruise

km/h (25 mph)

(cid:1) When vehicle stability control is acti-

vated

sure

button. Make

is cancelled and

When vehicle speed drops 16 km/h (10
mph) below the set speed, the cruise con- trol the set speed is erased from memory. The “CRUISE” indicator light remains on to indicate that the system is still in op- eration. To turn the cruise control off, press the “ON−OFF” the “CRUISE” indicator light is off. If the cruise control automatically cancels out other than for the above cases, have your vehicle checked by your Toyota deal- er at the earliest opportunity. RESUMING THE CRUISE CONTROL If the cruise control is temporarily can- celled, the cruising speed can be resumed by pushing the lever up in the “+ RES” direction. Vehicle speed must be above 40 km/h (25
mph).

130

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

SECTION 1− 8

OPERATION OF INSTRUMENTS AND CONTROLS Audio system Reference Using your audio system Audio system operating hints

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

132
132
144

131

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

Reference

Type 1: AM·FM radio/compact disc player (with compact disc changer controller)

Type 2: AM·FM radio/compact disc player with changer

132

’07 Corolla_U (L/O 0608)

Using your audio system— —Some basics This Section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR/VOL” to turn the audio system on and off. Push “AM”, “FM” or “DISC” to turn on that function without pushing “PWR/VOL”. You can turn on compact disc player by inserting a compact disc. You can turn off the compact disc player by ejecting the compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the compact disc. If the other func- tion was previously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “AM”, “FM” or “DISC” if the system is already on but you want to switch from one function to another.

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange (on some models) and bass levels. In fact, different kinds of music and vocal programs usually sound better with different mixes of treble, mi- drange and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

YOUR RADIO ANTENNA Your vehicle has a mast type antenna. To remove the antenna, carefully turn it counterclockwise.

NOTICE

To prevent damage to the antenna, make sure it is removed before driv- ing your Toyota through an automatic car wash.

YOUR COMPACT DISC PLAYER (type 1) When you insert a disc, gently push it in with the label side up. The player will play from track 1 through to the end of the disc. Then it will play from track 1 again.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

The player is intended for use with 12 cm (4.7 in.) discs only.

’07 Corolla_U (L/O 0608)

YOUR COMPACT DISC PLAYER WITH CHANGER (type 2) When you insert a disc, push the “LOAD” button and gently push the disc in with the label side up. The player will play from track 1 through to the end of the disc. Then it will play from track 1 of the next disc. The player is intended for use with 12 cm (4.7 in.) discs only.

NOTICE

(cid:1) Do not stack up two discs for in- sertion, or it will cause damage to the compact disc player. Insert only one compact disc into slot at a time.

(cid:1) Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

133

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

—Controls and features (cid:1)Type 1

Details of specific buttons, controls and features are described in the alphabetical list that follows.

134

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

(See

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset button number will appear on the display. To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM” button.)

(Eject button)

the compact disc eject button

Push eject a compact disc.

to

(Reverse/Fast−forward button)

Push and hold “ ” (preset button 6) or “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing.

AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONT (Tone and sound balance adjustment function) Each time you push the “AUDIO CONT” knob, the mode changes. To adjust the tone and balance, turn the knob. BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played.

inserted

incorrectly

Error messages If the player malfunctions, your audio sys- tem will display following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up−side down). Clean the disc and re−insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over−current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer.

135

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

in random order, or

the player will perform

RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.

feature, push

random

(cid:2) DISC (cid:1) With compact disc changer only— Use these buttons to select a disc you want to listen to. Push “(cid:2)” (preset button 3) or “(cid:1)” (preset button 4) until the number of the disc you want to listen appears on the display. FM Push the “FM” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each of the preset button. PWR/VOL (Power and Volume) Push “PWR/VOL” to turn the audio system on and off. Turn “PWR/VOL” to adjust the volume.

136

the

track

RPT (Repeat) There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again. With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 2) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan all the frequencies: Quickly push and release “(cid:1)” or “(cid:2)” side of the “SCAN” button. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push “(cid:1)” or “(cid:2)” side of this button again. To scan the preset stations: Push and hold “(cid:1)” or “(cid:2)” side of the “SCAN” button until you hear a beep. The radio will tune in the next preset station up or down the band, stay there for 5
seconds, and then move to the next pre- set station. To stop scanning, push “(cid:1)” or “(cid:2)” side of this button again.

’07 Corolla_U (L/O 0608)

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “(cid:1)” or “(cid:2)” side of the “SCAN” button. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. To stop scanning, push “(cid:1)” or “(cid:2)” side of this button again. If the player scanned all it will stop scanning. With compact disc changer only— Scanning the first tracks of all the discs in the magazine: Push and hold “(cid:1)” or “(cid:2)” side of the “SCAN” button until you hear a beep. ·SCAN” will appear on the display and “ the player will scan the first track on the next disc. To stop scanning, push “(cid:1)” or “(cid:2)” side of this button again. If the player has scanned all it will stop scanning.

the tracks on the disc,

the discs,

the seek mode,

the radio finds and the next station up or down the

SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release “(cid:1)” or “(cid:2)” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “(cid:1)” or “(cid:2)” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.

137

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

to

to

title,

track

then back

TEXT This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.

138

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

(cid:1)Type 2

Details of specific buttons, controls and features are described in the alphabetical list that follows.

139

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

(See

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset button number will appear on the display. To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. This radio can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM” button.)

(Eject button)

This button is used to eject one or all compact discs. To eject the current compact disc, push and release the compact disc eject button. To eject a specific disc, push “(cid:2)” (preset button 3) or “(cid:1)” (preset button 4) until the number of the disc you want to eject is displayed. Push and release the eject but- ton.

140

To eject all discs at a time, press and hold the eject button until you hear a beep. The last compact disc played before pushing the button will be ejected first. If the ejected disc is not removed for a long time, the eject function will be cancelled.

(Reverse/Fast−forward button)

Push and hold “ ” (preset button 6) or “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONT (Tone and sound balance adjustment function) Each time you push the “AUDIO CONT” knob, the mode changes. To adjust the tone and balance, turn the knob. BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. MID (on some models): Adjusts mid− pitched tones. The display ranges from −5
to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5.

FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will display following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up−side down). Clean the disc and re−insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again.

incorrectly

inserted

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

“ERROR 4”: Over−current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer. (cid:2) DISC (cid:1) Use these buttons to select a disc you want to listen to. Push “(cid:2)” (preset button 3) or “(cid:1)” (preset button 4) until the number of the disc you want to listen appears on the display. FM Push the “FM” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each of the preset button. LOAD This button is used to load the compact discs the compact disc player. This player can store up to six discs. To load one compact disc only, quickly push and release the button, then insert a compact disc. After the disc is loaded, the shutter of the slot will close.

in

If no compact disc is inserted, the shutter will close after 15 seconds. To load multiple compact discs, push and hold the button (until you hear a beep when the audio system is on), then insert the first compact disc. After the disc is loaded, the shutter of the slot will close. After a few seconds, the shutter will auto- matically open again so the next disc can be inserted. The same process can be applied for loading the rest of the discs. If the player is full of discs, “DISC FULL” will appear on the display. If no compact disc is inserted, the shutter will close after 15 seconds. PWR/VOL (Power and Volume) Push “PWR/VOL” to turn the audio system on and off. Turn “PWR/VOL” to adjust the volume. RDS (Radio Data System) display The radio will automatically switch to the RDS mode to receive an RDS station while turned to FM broadcasts. “RDS” will appear on the display.

in random order, or

RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.

the player will perform

feature, push

random

141

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. Scanning the first tracks of all the discs in the magazine: Push the “SCAN” button until you hear a ·SCAN” will appear on the dis- beep. “ play and the first the player will scan track on the next disc. To stop scanning, push this button again. If the changer has scanned all the discs, it will stop scan- ning.

listening

the

track

RPT (Repeat) There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again. Repeating a disc: Push and hold “RPT” (preset button 2) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again.

142

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

the seek mode,

the radio finds and the next station up or down the

SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release “(cid:1)” or “(cid:2)” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “(cid:1)” or “(cid:2)” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.

in RDS

to change

transmits a

is operational only

TEXT Radio This button mode. When an RDS station text message, “MSG” will appear on the dis- played. To display the text message, first push the “TEXT” button the radio station display. Then push the “TEXT” but- ton once more to display, and the mes- sage will appear on the display. If the entire the message is not displayed, ” will appear on the display. To display “ the rest of the message, push and hold the “TEXT” button until you hear a beep. After the entire message has been dis- played, the message will disappear. The message display will be canceled if any button is pushed. If no messages are “NO MESSAGE” will appear on the display, and the display returns to the previous mode. The message display will be canceled if you activate any function that affects the display.

that affects

the display

received,

to

to

title,

track

then back

Compact disc player This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear. TRAF (Traffic) This button turns the traffic announcement (TA) feature on and off. This button is operational only in FM mode. By pushing “TRAF SEEK” will flash on the display and the radio will start seeking any traffic program station. When a traffic program station is found, “TRAF” will be displayed and you will hear a beep.

“TRAF” button,

the

143

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

After the traffic announcement program is over, the display returns to the previous mode. If no traffic program station is found, “NO TRAF INFO” appears on the display, and the display returns to the previous mode and a beep sound. To cancel the traffic announcement, push this button again. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency. TYPE (Program Types) When you push “(cid:1)” or “(cid:2)” of the “TYPE” button while receiving an RDS station, the current program type will appear on the display. If the system is receiving a sta- tion that is not RDS, “NO PTY” will ap- pear. Repeat this operation within 6 seconds to display the program types in the following order: (cid:2) ROCK (cid:2) EASY LIS (Easy listening) (cid:2) CLS/JAZZ (Classical music and Jazz) (cid:2) R&B (Rhythm and Blues)

144

’07 Corolla_U (L/O 0608)

(cid:2) INFORM (Information) (cid:2) RELIGION (cid:2) MISC (Miscellaneous) (cid:2) ALERT (Emergency message) To seek or scan for the same type of program, push “SEEK/TRACK” or “SCAN” button while the program type is displayed. If no program is found, “NOTHING” will appear on the display. The previous pro- gram information will resume. When the system is left untouched for 6
seconds, type display will change to the frequency display.

the program

the

Audio system operating hints

NOTICE

To ensure correct audio system op- erations: (cid:1) Be careful not to spill beverages

over the audio system.

(cid:1) Do not put anything other than

Compact Disc into the slot.

(cid:1) The use of a cellular phone inside or near the vehicle may cause a noise from the speakers of the au- dio system which you are listening to. However, this does not indicate a malfunction.

RADIO RECEPTION Usually, a problem with radio reception does not mean there is a problem with your radio—it is just the normal result of conditions outside the vehicle. For example, nearby buildings and terrain can interfere with FM reception. Power lines or telephone wires can interfere with AM signals. And of course, radio signals have a limited range. The farther you are from a station, the weaker its signal will be. conditions change constantly as your vehicle moves.

In addition,

reception

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

signals are

Here are some common reception prob- lems that probably do not indicate a prob- lem with your radio: FM Fading and drifting stations—Generally, the effective range of FM is about 40 km (25
miles). Once outside this range, you may notice fading and drifting, which increase with the distance from the radio transmit- ter. They are often accompanied by distor- tion. Multi−path—FM reflective, making it possible for two signals to reach your antenna at the same time. If this happens, the signals will cancel each oth- er out, causing a momentary flutter or loss of reception. Static and fluttering—These occur when signals are blocked by buildings, trees, or other large objects. Increasing the bass level may reduce static and fluttering. the FM signal you Station swapping—If are interrupted or weak- is ened, and there is another strong station nearby on the FM band, your radio may tune in the second station until the origi- nal signal can be picked up again.

listening to

’07 Corolla_U (L/O 0608)

AM Fading—AM broadcasts are reflected by the upper atmosphere—especially at night. These reflected signals can interfere with those received directly from the radio sta- tion, causing the radio station to sound alternately strong and weak. Station interference—When a reflected sig- nal and a signal received directly from a radio station are very nearly the same frequency, interfere with each other, making it difficult to hear the broad- cast. Static—AM is easily affected by external sources of electrical noise, such as high tension power lines, lightening, or electri- cal motors. This results in static.

they can

CARING FOR YOUR COMPACT DISC PLAYER AND DISCS (cid:2) Your compact disc player is intended for use with 12 cm (4.7 in.) discs only. (cid:2) Extremely high temperatures can keep your compact disc player from working. On hot days, use the air conditioning to cool the vehicle interior before you listen to a disc.

(cid:2) Bumpy roads or other vibrations may

make your compact disc player skip.

(cid:2) If moisture gets into your compact disc player, you may not hear any sound even though your compact disc player appears the disc from the player and wait until it dries.

to be working. Remove

CAUTION

Compact disc players use an invisible laser beam which could cause hazard- ous if directed outside the unit. Be sure to operate the player correctly.

radiation exposure

145

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Special shaped discs

Low quality discs

(cid:2) Use only compact discs marked as shown above. The following products may not be playable on your compact disc player. Copy−protected CD CD−R (CD−Recordable) CD−RW (CD−Re−writable) CD−ROM

146

Transparent/translucent discs

Labeled discs

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

NOTICE

Do not use special shaped, transpar- ent/translucent, low quality or labeled discs such as those shown in the il- lustrations. The use of such discs may damage the player or changer, or it may be impossible to eject the disc.

Correct

Wrong

inserting

(cid:2) Handle compact discs carefully, espe- them. cially when you are them on the edge and do not Hold them. Avoid getting fingerprints bend on them, particularly on the shiny side. (cid:2) Dirt, scratches, warping, pin holes, or other disc damage could cause the player to skip or to repeat a section of a track. (To see a pin hole, hold the disc up to the light.)

(cid:2) Remove discs from the compact disc player when you are not listening to them. Store them in their plastic cases away from moisture, heat, and direct sunlight.

To clean a compact disc: Wipe it with a soft, lint−free cloth that has been damp- ened with water. Wipe in a straight line from the center to the edge of the disc (not in circles). Dry it with another soft, lint−free cloth. Do not use a conventional record cleaner or anti−static device.

147

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

148

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

SECTION 1− 9

OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Controls Air flow selector settings Operating tips Side vents Air conditioning filter

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

150
153
153
156
156

149

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

Controls

150

’07 Corolla_U (L/O 0608)

1. “A/C” button (on some models) 2. Air intake selector 3. Temperature selector 4. Fan speed selector 5. Air flow selector

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Fan speed selector Turn the knob to adjust the fan speed—to the right to increase, to the left to de- crease. Temperature selector Turn the knob to adjust the temperature— to the right to warm, to the left to cool.

this position, air

In intake selector mode changes to FRESH automatically to clean up the front view quickly. It is not possible to return to RECIRCULATE in this position. Press the “A/C” button for dehumidified heating or cooling. This setting clears the front view more quickly.

5. Windshield—Air flows mainly from the

Air flow selector Turn the knob to select the vents used for air flow. 1. Panel—Air

flows mainly

from

the

instrument panel vents.

2. Bi−level—Air flows from both the floor vents and the instrument panel vents. 3. Floor—Air flows mainly from the floor

vents.

the

4. Floor/Windshield—Air

flows mainly floor vents and windshield

from vents. the Turning floor/windshield position the defogging function with the purpose of clearing the front view.

to turns on

flow selector

the air

to

flow selector

this position, air

windshield vents. Turning the the air windshield position turns on the defog- ging function with the purpose of clear- ing the front view. In intake selector mode changes to FRESH automatically to clean up the front view quickly. It is not possible to return to RECIRCULATE in this position. Press the “A/C” button for dehumidified heating or cooling. This setting clears the front view more quickly.

For details about air flow selector settings, see “Air flow selector settings” described below.

151

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

“A/C” button To turn on the air conditioning, press the “A/C” button. The “A/C” button indicator will come on. To turn the air conditioning off, press the button again. If the “A/C” button indicator flashes, there is a problem in the air conditioning system and the air conditioning automatically shuts off. If this happens, take your ve- hicle to a Toyota dealer for service.

Air intake selector Press the button to select the air source. 1. Recirculate (indicator light is on)—Re-

circulates the air inside the vehicle.

2. Fresh

(indicator

light

is off)—Draws

outside air into the system.

To prevent fogging up of the windshield, the air intake mode may change automati- cally to FRESH depending on the condi- tion of the air conditioning system.

152

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

Air flow selector settings

’07 Corolla_U (L/O 0608)

Operating tips (cid:1) To cool off your Toyota after

it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.

(cid:1) Make sure the air intake grilles in front of the windshield are not blocked (by leaves or snow, for example).

(cid:1) On humid days, do not blow cold air on the windshield. The windshield could fog up because of the difference in air temperature on the inside and outside of the windshield.

(cid:1) Keep the area under the front seats clear to allow air to circulate through- out the vehicle.

for a minute

(cid:1) On cold days, set the fan speed to high the intake ducts of snow or moisture. This can reduce the amount of fogging on the windows.

to help clear

: On some models

153

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

(cid:1) When driving on dusty roads, close all windows. If dust thrown up by the ve- hicle is still drawn into the vehicle after closing the windows, it is recommended that the air intake selector be set to FRESH and the fan speed selector to any setting except “OFF”.

(cid:1) If following another vehicle on a dusty road, or driving in windy and dusty conditions, it is recommended that the air intake selector be temporarily set to RECIRCULATE, which will close off the outside passage and prevent outside air and dust from entering the vehicle interior.

154

’07 Corolla_U (L/O 0608)

Heating For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards red zone Air intake—FRESH (outside air) Air flow—FLOOR Air conditioning—OFF

for a

few minutes. To keep

(cid:1) For quick heating, select recirculated air the windows from fogging, select fresh af- ter interior has been warmed.

the vehicle

(cid:1) Press the “A/C” button on for dehumidi-

fied heating.

(cid:1) Choose floor/windshield air flow to heat the vehicle interior while defrosting or defogging the windshield.

Air conditioning For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards blue zone Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—ON

(cid:1) For quick cooling, turn the temperature selector knob fully counterclockwise (into the blue zone) and change the air intake selector mode to RECIRCULATE.

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

Ventilation For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards blue zone Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—OFF

’07 Corolla_U (L/O 0608)

Defogging The inside of the windshield For best results, set controls to:

Defrosting The outside of the windshield For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards red zone to heat;

blue zone to cool Air intake—FRESH (outside air) Air flow—WINDSHIELD

Turning the air flow selector to the wind- shield or floor/windshield position turns on the defogging function with the purpose of clearing the front view. When turning the air flow selector to wind- shield or floor/windshield position, air in- take selector mode changes to FRESH automatically to clean up the front view quickly. to RECIRCULATE in this position. Press for dehumidified heating or cooling. This setting clears the front view more quickly. (cid:1) On humid days, do not blow cold air on the windshield—the difference be- tween the outside and inside tempera- tures could make the fogging worse.

the “A/C” button

is not possible

to return

It

Fan speed—Any setting except “OFF” Temperature—Towards red zone Air intake—FRESH (outside air) Air flow—WINDSHIELD

Turning the air flow selector to the wind- shield or floor/windshield position turns on the defrosting function with the purpose of clearing the front view. When turning the air flow selector to wind- shield or floor/windshield position, air in- take selector mode changes to FRESH automatically to clean up the front view quickly. to RECIRCULATE in this position. Press for dehumidified heating. This setting clears the front view more quickly. (cid:1) To heat the vehicle interior while de- choose

the “A/C” button

is not possible

windshield,

to return

frosting floor/windshield air flow.

the

It

155

2007MY COROLLA from Oct. ’06 Prod. (OM12B32U)

’07 Corolla_U (L/O 0608)

Side vents

Air conditioning filter (on some models)—

If air flow control is not satisfactory, check the side vents. The side vents may be opened or closed as shown.

The air conditioning filter information label is placed inside of the glove box as shown and indicates that a filter has been installed.