STEP 2
When the indicator light on the key surface is not on, press and hold for about 5 seconds while pressing and holding
, or
The setting changes each time an operation is performed, as shown below. (When changing the setting continuously, release the buttons, wait for at least 5 seconds, and repeat step 2.)
Unlocking doors
Beep
Holding the driver's door handle unlocks only the driver's door. Holding the front passenger’s door handle unlocks all the doors. Holding either front door handle unlocks all the doors.
Exterior: Beeps 3 times Interior: Beeps once
Exterior: Beeps twice Interior: Beeps once
Vehicles with an alarm system: To prevent unintended triggering of the alarm, unlock the doors using the wireless remote control and open and close a door once after the settings have been changed. (If a door is not opened within 60 seconds after is pressed, the doors will be locked again and the alarm will automatically be set.) In case that the alarm is triggered, immediately stop the alarm. (→P. 95)
38
1
1-2. Opening, closing and locking the doors and trunk
■Battery-saving function
The battery-saving function will be activated in order to prevent the elec- tronic key battery and the vehicle battery from being discharged while the vehicle is not in operation for a long time. ●In the following situations, the smart key system may take some time to
unlock the doors. • The electronic key has been left in an area of approximately 6 ft. (2 m)
of the outside of the vehicle for 10 minutes or longer.
• The smart key system has not been used for 5 days or longer.
●If the smart key system has not been used for 14 days or longer, the doors cannot be unlocked at any doors except the driver’s door. In this case, take hold of the driver’s door handle, or use the wireless remote control or the mechanical key, to unlock the doors.
■Electronic key battery-saving function
When battery-saving mode is set, battery depletion is minimized by stopping the electronic key from receiving radio waves.
twice while pressing and . Confirm that the electronic
Press holding key indicator flashes 4 times. While the battery-saving mode is set, the smart key system cannot be used. To cancel the function, press any of the elec- tronic key buttons.
39
1-2. Opening, closing and locking the doors and trunk
■Conditions affecting operation
The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system, wireless remote control and engine immobilizer system from operating properly. (Ways of coping: →P. 451) ●When the electronic key battery is depleted ●Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electri- cal noise
●When the electronic key is in contact with, or is covered by the following
metallic objects • Cards to which aluminum foil is attached • Cigarette boxes that have aluminum foil inside • Metallic wallets or bags • Coins • Hand warmers made of metal • Media such as CDs and DVDs
●When other wireless key (that emit radio waves) is being used nearby ●When carrying the electronic key together with the following devices that
emit radio waves • A portable radio, cellular phone, cordless phone or other wireless com-
munication device
waves
• Another vehicle’s electronic key or a wireless key that emits radio
• Personal computers or personal digital assistants (PDAs) • Digital audio players • Portable game systems
●If window tint with a metallic content or metallic objects are attached to
the rear window
●When the electronic key is placed near a battery charger or electronic
devices
40
1
1-2. Opening, closing and locking the doors and trunk
■Notes for the entry function
●Even when the electronic key is within the effective range (detection
areas), the system may not operate properly in the following cases: • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.
• The electronic key is near the ground or in a high place, or too close to
the rear bumper center when the trunk is unlocked.
• The electronic key is on the instrument panel, rear package tray or floor, in the door pockets or glove box, or near a vent when the engine is started or “ENGINE START STOP” switch modes are changed.
●Do not leave the electronic key on top of the instrument panel or near the door pockets or a vent when exiting the vehicle. Depending on the radio wave reception conditions, it may be detected by the antenna outside the cabin and the door will become lockable from the outside, possibly trap- ping the electronic key inside the vehicle.
●As long as the electronic key is within the effective range, the doors may
be locked or unlocked by anyone.
●Even if the electronic key is not inside the vehicle, it may be possible to
start the engine if the electronic key is near the window.
●The doors may unlock if a large amount of water splashes on the door handle, such as in the rain or in a car wash when the electronic key is within the effective range. (The door will automatically be locked after approximately 60 seconds if the doors are not opened and closed.)
●Gripping the door handle when wearing a glove may not unlock the door. ●If the wireless remote control is used to lock the doors when the elec- tronic key is near the vehicle, there is a possibility that the door may not be unlocked by the entry function. (Use the wireless remote control to unlock the doors.)
●A sudden approach to the effective range or door handle may prevent the doors from being unlocked. In this case, return the door handle to the original position and check that the doors unlock before pulling the door handle again.
41
1-2. Opening, closing and locking the doors and trunk
■Notes for locking the doors
●Touching the door lock sensor while wearing gloves may delay or prevent
lock operation. Remove the gloves and touch the lock sensor again.
●When the lock operation is performed using the lock sensor, recognition signals will be shown up to two consecutive times. After this, no recogni- tion signals will be given.
●If the door handle becomes wet while the electronic key is within the effective range, the door may lock and unlock repeatedly. In that case, follow the following correction procedures to wash the vehicle: • Place the electronic key in a location 6 ft. (2 m) or more away from the
vehicle. (Take care to ensure that the key is not stolen.)
• Set the electronic key to battery-saving mode to disable the smart key
system. (→P. 39)
●If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a buzzer will sound outside the vehicle. To turn off the alarm, lock all the doors.
●The lock sensor may not work properly if it comes into contact with ice,
snow, mud, etc. Clean the lock sensor and attempt to operate it again.
■Notes for the unlocking function
●A sudden approach to the effective range or door handle may prevent the doors from being unlocked. In this case, return the door handle to the original position and check that the doors unlock before pulling the door handle again.
●Gripping the door handle when wearing a glove may not unlock the door. Remove the gloves and touch the sensor on the back of the handle again.
●If the door handle becomes wet while the electronic key is within the effective range, the door may lock and unlock repeatedly. In that case, follow the following correction procedures to wash the vehicle: • Place the electronic key in a location 6 ft. (2 m) or more away from the
vehicle. (Take care to ensure that the key is not stolen.)
• Set the electronic key to battery-saving mode to disable the smart key
system. (→P. 39)
●If there is another electronic key in the detection area, it may take slightly
longer to unlock the doors after the door handle is gripped.
42
1
1-2. Opening, closing and locking the doors and trunk
■When the vehicle is not driven for extended periods
●To prevent theft of the vehicle, do not leave the electronic key within 6 ft.
(2 m) of the vehicle.
●The smart key system can be deactivated in advance. (→P. 493)
■Alarm (if equipped)
Using the smart key system to lock the doors will set the alarm system. (→P. 95)
■To operate the system properly
Make sure to carry the electronic key when operating the system. Do not get the electronic key too close to the vehicle when operating the system from the outside of the vehicle. Depending on the position and holding condition of the electronic key, the key may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door lock prevention function may not operate.)
■If the smart key system does not operate properly
●Locking and unlocking the doors: Use the mechanical key. (→P. 451)
●Starting the engine: →P. 451
43
1-2. Opening, closing and locking the doors and trunk
■Electronic key battery depletion
●The standard battery life is 1 to 2 years. ●If the battery becomes low, an alarm will sound in the cabin when the
engine stops. (→P. 427)
●As the electronic key always receives radio waves, the battery will become depleted even if the electronic key is not used. The following symptoms indicate that the electronic key battery may be depleted. Replace the battery when necessary. (→P. 386) • The smart key system or the wireless remote control does not operate. • The detection area becomes smaller. • The LED indicator on the key surface does not turn on.
●To avoid serious deterioration, do not leave the electronic key within 3 ft. (1 m) of the following electrical appliances that produce a magnetic field: • TVs • Personal computers • Cellular phones, cordless phones and battery chargers • Recharging cellular phones or cordless phones • Glass top ranges • Table lamps
■When the electronic key battery is fully depleted
→P. 386
■If the smart key system has been deactivated in a customized setting ●Locking and unlocking the doors: Use the wireless remote control or
mechanical key. (→P. 46, 451)
●Starting the engine and changing “ENGINE START STOP” switch
modes: →P. 452
●Stopping the engine: →P. 149
■Customization that can be configured at Toyota dealer
Settings (e. g. smart key system) can be changed. (Customizable features: →P. 493)
44
1
1-2. Opening, closing and locking the doors and trunk
■Certification for the smart key system
U.S.A.
FCC ID: NI4TMLF10-4
FCC ID: NI4TMLF10-5
FCC ID: HYQ23AAB
FCC ID: HYQ14FBA
NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Canada
NOTE:
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, includ-
ing interference that may cause undesired operation of the device.
CAUTION
■Caution regarding interference with electronic devices
●People with implanted pacemakers or cardiac defibrillators should keep
away from the smart key system antennas. (→P. 34) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves. Then, consult your doctor to see if you should disable the entry function.
●Users of any electrical medical device other than implanted pacemakers and implanted cardiac defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.
Ask your Toyota dealer for details for disabling the entry function.
45
1-2. Opening, closing and locking the doors and trunk Wireless remote control∗
The wireless remote control can be used to lock and unlock the vehi- cle. Vehicles without a smart key system (type A)
Locks all the doors Sounds the alarm (press and hold) Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Opens the driver’s window and moon roof (press and hold)* Unlocks the trunk (press and hold)
*: This setting must be custom-
ized at your Toyota dealer.
46
∗: If equipped
1
1-2. Opening, closing and locking the doors and trunk
Vehicles without a smart key system (type B)
Vehicles with a smart key system
Locks all the doors Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Opens the driver’s window and moon roof (press and hold)* Sounds the alarm (press and hold) Unlocks the trunk (press and hold)
*: This setting must be custom-
ized at your Toyota dealer.
Locks all the doors Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Opens the driver’s window and moon roof (press and hold)* Unlocks the trunk (press and hold) Sounds the alarm (press and hold)
*: This setting must be custom-
ized at your Toyota dealer.
47
1-2. Opening, closing and locking the doors and trunk
■Operation signals
Doors: A buzzer sounds and the emergency flashers flash to indicate that
the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)
Trunk: A buzzer sounds to indicate that the trunk has been unlocked. Driver’s window and moon roof: A buzzer sounds to indicate that the driver’s
window and moon roof are opening.
■Door lock buzzer
If an attempt to lock the doors is made when a door is not fully closed, a buzzer sounds continuously. Fully close the door to stop the buzzer, and lock the vehicle once more.
■Panic mode
Vehicles without a smart key system
When is pressed for longer than about one second, an alarm will sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the wireless remote control.
48
1
1-2. Opening, closing and locking the doors and trunk
Vehicles with a smart key system
When is pressed for longer than about one second, an alarm will sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the electronic key.
■Security feature
If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.
■Alarm (if equipped)
Using the wireless remote control to lock the doors will set the alarm system. (→P. 95)
49
1-2. Opening, closing and locking the doors and trunk
■Conditions affecting operation
Vehicles without a smart key system The wireless remote control function may not operate normally in the follow- ing situations: ●When the wireless key battery is depleted ●Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electri- cal noise
●When carrying a portable radio, cellular phone or other wireless commu-
nication devices
●When the wireless key is in contact with, or is covered by a metallic
object
●When other wireless key (that emit radio waves) is being used nearby ●If window tint with a metallic content or metallic objects are attached to
the rear window
Vehicles with a smart key system
→P. 40
■If the wireless remote control does not operate properly (vehicles with
a smart key system) Locking and unlocking the doors: Use the mechanical key. (→P. 451)
■Key battery depletion
Vehicles without a smart key system
If the wireless remote control function does not operate, the battery may be
depleted. Replace the battery when necessary. (→P. 384)
Vehicles with a smart key system
→P. 44
■When the key battery is fully depleted
→P. 384
■Confirmation of the registered key number (vehicles with a smart key
system) The number of keys already registered to the vehicle can be confirmed. Ask your Toyota dealer for details.
50
1
1-2. Opening, closing and locking the doors and trunk
■Customization that can be configured at Toyota dealer
Settings (e.g. wireless remote control system) can be changed. (Customizable features: →P. 493)
■Certification for wireless remote control
U.S.A. (vehicles without a smart key system)
FCC ID: HYQ23AAC
FCC ID: HYQ12BDM
NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
U.S.A. (vehicles with a smart key system)
FCC ID: NI4TMLF10-4
FCC ID: NI4TMLF10-5
FCC ID: HYQ23AAB
FCC ID: HYQ14FBA
NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Canada
NOTE:
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, includ-
ing interference that may cause undesired operation of the device.
51
1-2. Opening, closing and locking the doors and trunk Doors
The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch. ■ Entry function (vehicles with a smart key system)
→P. 32
■ Wireless remote control (if equipped)
→P. 46
■ Key Turning the key operates the doors as follows: Vehicles without a smart key system
Locks all the doors Unlocks all the doors Driver’s side only: Turning the key unlocks the driver's door. Turning the key again unlocks the other doors.
Vehicles with a smart key system The doors can also be locked and unlocked with the mechanical key. (→P. 451) ■ Door lock switch
Locks all the doors Unlocks all the doors
52
1
1-2. Opening, closing and locking the doors and trunk
■ Inside lock button
Unlocks the door Locks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.
Locking the doors from the outside without a key
STEP 1
STEP 2
Move the inside lock button to the lock position. Close the door.
Vehicles without a smart key system
The door cannot be locked if either of the front doors is open and the key is in the engine switch.
Vehicles with a smart key system
The door cannot be locked if the “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode, or the electronic key is left inside the vehicle. The key may not be detected correctly and the door may be locked.
53
1-2. Opening, closing and locking the doors and trunk
Rear door child-protector lock
The door cannot be opened from inside the vehicle when the lock is set.
Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.
54
1-2. Opening, closing and locking the doors and trunk
Automatic door locking and unlocking systems
The following functions can be set or cancelled:
Function
Shift position linked door locking function Shift position linked door unlocking function
Speed linked door lock- ing function
Operation
Shifting the shift lever out of P locks all the doors. Shifting the shift lever to P unlocks all the doors. All the doors are locked when the vehicle speed is approximately 12 mph (20 km/h) or higher.
All the doors are unlocked when the driver's door is opened within 10 seconds after turn- ing the engine switch to “ACC” or “LOCK”.
Driver's door linked door unlocking function (vehicles without a smart key system) Driver's door linked door unlocking function (vehicles with a smart key system) ■ Setting and canceling the functions (vehicles without naviga-
All the doors are unlocked when the driver's door is opened within 10 seconds after turn- ing the “ENGINE START STOP” switch off.
tion system and Display Audio system) To switch between setting and canceling, follow the procedure below.
STEP 1
Vehicles without a smart key system Close all the doors and turn the engine switch to the “ON” position. (Perform step 2 within 10 seconds.) Vehicles with a smart key system Close all the doors and turn the “ENGINE START STOP” switch to IGNITION ON mode. (Perform step 2 within 10 sec- onds.)
55
1-2. Opening, closing and locking the doors and trunk
STEP 2
Shift the shift lever to P or N, and press and hold the driver's door lock for approximately 5 seconds and then release.
switch
or
to
corresponding
The shift lever and switch posi- tions the desired function to be set are shown in the following table. Use the same procedure to can- cel the function.
Function
Shift lever position
Driver’s door lock switch position
Shift position linked door lock- ing function Shift position linked door unlocking function Speed linked door locking func- tion Driver's door linked door unlock- ing function
When the setting or canceling operation is complete, all doors are locked and then unlocked.
56
1-2. Opening, closing and locking the doors and trunk
■If a wrong key is used (vehicles with a smart key system)
The key cylinder rotates freely to isolate inside mechanism.
■If the smart key system has been deactivated in a customized setting
(vehicles with a smart key system) Use the wireless remote control or mechanical key. (→P. 46, 451)
■Customization that can be configured at Toyota dealer
Settings (e.g. unlocking function using a key) can be changed. (Customizable features →P. 493)
CAUTION
■To prevent an accident
Observe the following precautions while driving the vehicle. Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●Always use a seat belt. ●Always lock all the doors. ●Ensure that all doors are properly closed. ●Do not pull the inside handle of the doors while driving.
The doors may be opened and the passengers are thrown out of the vehi- cle and it may result in serious injury or death. Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in locked position.
●Set the rear door child-protector locks when children are seated in the rear
seats.
57
1-2. Opening, closing and locking the doors and trunk Trunk
The trunk can be opened using the key, trunk opener, entry function or wireless remote control. ■ Opening the trunk from inside the vehicle
Pull up the lever to release the trunk lid.
■ Opening the trunk from outside the vehicle Key (vehicles without a wireless remote control)
Turn the master key clockwise to release the trunk lid.
Entry function (vehicles with a smart key system)
→P. 32
Wireless remote control (if equipped)
→P. 46
58
1
1-2. Opening, closing and locking the doors and trunk
■Trunk light
The trunk light turns on when the trunk is opened.
■Function to prevent the trunk being locked with the electronic key
inside (vehicles with a smart key system) ●When all doors are being locked, closing the trunk lid with the electronic
key left inside the trunk will sound an alarm. In this case, the trunk lid can be opened using the entry function.
●Even when the spare electronic key is put in the trunk with all the doors locked, the key confinement prevention function can be activated so the trunk can be opened. In order to prevent theft, take all electronic keys with you when leaving the vehicle.
●Even when the electronic key is put in the trunk with all the doors are locked, the key may not be detected depending on the places and the surrounding radio wave conditions. In this case, the key confinement pre- vention function cannot be activated, causing the doors to lock when the trunk is closed. Make sure to check where the key is before closing the trunk.
●The key confinement prevention function cannot be activated if any one of the doors is unlocked. In this case, open the trunk using the trunk opener.
■Internal trunk release lever
The trunk lid can be opened by pulling up the glow-in-the-dark lever located on the inside of the trunk lid. The lever will continue to glow for some time after the trunk lid is closed.
59
1-2. Opening, closing and locking the doors and trunk
CAUTION
■Caution while driving
●Keep the trunk lid closed while driving.
If the trunk lid is left open, it may hit near-by objects while driving or lug- gage in the trunk may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard. Make sure to close the trunk lid before driving.
●Before driving the vehicle, make sure that the trunk lid is fully closed. If the trunk lid is not fully closed, it may open unexpectedly while driving, caus- ing an accident.
●Never let anyone sit in the trunk. In the event of sudden braking or a colli-
sion, they are susceptible to death or serious injury.
■When children are in the vehicle Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not allow children to enter the trunk.
If a child is accidentally locked in the trunk, they could overheat or suffo- cate.
●Do not allow a child to open or close the trunk lid.
Doing so may cause the trunk lid to operate unexpectedly, or cause the child’s hands, head, or neck to be caught by the closing trunk lid.
60
1
1-2. Opening, closing and locking the doors and trunk
CAUTION
■Using the trunk
Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in seri- ous injury. ●Remove any heavy loads, such as snow and ice, from the trunk lid before opening it. Failure to do so may cause the trunk lid to fall closed again after it is opened.
●When opening or closing the trunk lid, thoroughly check to make sure the
surrounding area is safe.
●If anyone is in the vicinity, make sure they are safe and let them know that
the trunk is about to open or close.
●Use caution when opening or closing the trunk lid in windy weather as it
may move abruptly in strong wind.
●The trunk lid may fall if it is not opened fully. It is more difficult to open or close the trunk lid on an incline than on a level surface, so beware of the trunk lid unexpectedly opening or closing by itself. Make sure that the trunk lid is fully open and secure before using the trunk.
●When closing the trunk lid, take extra care to prevent your fingers etc. from being caught.
●When closing the trunk lid, make sure
to press it lightly on its outer surface.
●Do not attach any accessories other than genuine Toyota parts to the trunk lid. Such additional weight on the trunk lid may cause the lid to fall closed again after it is opened.
61
1-2. Opening, closing and locking the doors and trunk
62
1-2. Opening, closing and locking the doors and trunk
63
1-3. Adjustable components (seats, mirrors, steering wheel) Front seats
Manual seat
Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever (driver’s side only)
62
1-3. Adjustable components (seats, mirrors, steering wheel)
Power seat
Seat position adjustment switch Seatback angle adjustment switch Seat cushion (front) angle adjustment switch (driver’s side only) Vertical height adjustment switch (driver’s side only) Lumbar support adjustment switch (driver’s side only)
63
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Seat adjustment
●To reduce the risk of sliding under the lap belt during a collision, do not
recline the seat more than necessary. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen, or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident. Adjustments should not be made while driving as the seat may unexpect- edly move and cause the driver to lose control of the vehicle.
●Manual seat only: After adjusting the seat, make sure that the seat is
locked in position.
64
1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats
The seatbacks of the rear seats can be folded down.
Folding down the rear seatbacks
Pull the seatback lever in the trunk for the seatback you wish to fold down.
CAUTION
■When folding the rear seatbacks down
Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not fold the seatbacks down while driving. ●Stop the vehicle on level ground, set the parking brake and shift the shift
lever to P.
●Do not allow anyone to sit on a folded seatback or in the trunk while driv-
ing.
●Do not allow children to enter the trunk.
65
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■When returning the seat to its original position
●Ensure that the seat belt does not get caught between or behind the seats. ●If the seat belt has been released from its guide, pass the seat belt through
its guide. (→P. 72)
■Seat adjustment
Be careful not to get hands or feet pinched between the rear console box and the rear seat when folding down the rear seatback. ■After returning the seatback to the upright position
Observe the following precautions. Failure to do so may result in death or serious injury. ●Make sure the seatback is securely locked by pressing it forward and rear-
ward on the top.
●Check that the seat belts are not twisted or caught in the seatback. ●Make sure that the seat belt is passing through its guide.
NOTICE
■When left seatback is folded down
Make sure the luggage loaded in the enlarged trunk will not damage the webbing of the rear center seat belt.
66
1
1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints
Head restraints are provided for all seats.
(front
adjustment
Vertical seats) Up Pull the head restraints up. Down Push the head restraint down while pushing the lock release button.
Lock release button
■Removing the head restraints (front seats)
Pull the head restraint up while pressing the lock release button.
■Installing the head restraints (front seats)
Align the head restraint with the installa- tion holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.
67
1-3. Adjustable components (seats, mirrors, steering wheel)
■Adjusting the height of the head restraints (front seats)
Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.
CAUTION
■Head restraint precautions (front seats)
Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ●Use the head restraints designed for each respective seat. ●Adjust the head restraints to the correct position at all times. ●After adjusting the head restraints, push down on them and make sure
they are locked in position.
●Do not drive with the head restraints removed.
68
1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts
Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts
● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoul- der.
● Position the lap belt as low
as possible over the hips.
● Adjust the position of the seatback. Sit up straight and well back in the seat. ● Do not twist the seat belt.
■ Fastening and releasing the seat belt
To fasten the seat belt, push the plate into the buckle until a click sound is heard. To release the seat belt, press the release button.
Release button
69
1-3. Adjustable components (seats, mirrors, steering wheel)
■ Adjusting the seat belt shoulder anchor height (front seats) Push the seat belt shoulder anchor down while pressing the release button. Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed until you hear a click.
Seat belt pretensioners (front seats)
The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal or side collision.
The pretensioner may not acti- vate in the event of a minor frontal impact, a minor side impact, a rear impact or a vehicle rollover.
70
1-3. Adjustable components (seats, mirrors, steering wheel)
■Emergency locking retractor (ELR)
The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
■Automatic locking retractor (ALR)
When a passenger's shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly. To free the belt again, fully retract the belt and then pull the belt out once more. (→P. 122)
■Pregnant women
Obtain medical advice and wear the seat belt in the proper way. (→P. 69) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants. Extend the shoulder belt com- pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area. If the seat belt is not worn properly, not only a pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking or a collision.
■People suffering illness
Obtain medical advice and wear the seat belt in the proper way. (→P. 69)
■Child seat belt usage
The seat belts of your vehicle were principally designed for persons of adult size. ●Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle's seat belt. (→P. 118) ●When the child becomes large enough to properly wear the vehicle's seat
belt, follow the instructions on P. 69 regarding seat belt usage.
71
1-3. Adjustable components (seats, mirrors, steering wheel)
■Replacing the belt after the pretensioner has been activated
If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli- sions.
■Seat belt extender
If your seat belts cannot be fastened securely because long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.
they are not
Use the seat belt after passing it through the guide if the seat belt comes free from the guide.
■Rear seat belt
72
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failure to do so may cause death or severe injury. ■Wearing a seat belt
●Ensure that all passengers wear a seat belt. ●Always wear a seat belt properly. ●Each seat belt should be used by one person only. Do not use a seat belt
for more than one person at once, including children.
●Toyota recommends that children be seated in the rear seat and always
use a seat belt and/or an appropriate child restraint system.
●To achieve a proper seating position, do not recline the seat more than necessary. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.
●Do not wear the shoulder belt under your arm. ●Always wear your seat belt low and snug across your hips.
■When children are in the vehicle
Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.
■Seat belt pretensioners
●Do not place anything, such as a cushion, on the front passenger's seat. Doing so will disperse the passenger's weight, which prevents the sensor from detecting the passenger's weight properly. As a result, the seat belt pretensioner for the front passenger's seat may not activate in the event of a collision.
●If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.
73
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Adjustable shoulder anchor
Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in the event of a sudden stop, sudden swerve or accident. (→P. 70)
■Seat belt damage and wear
●Do not damage the seat belts by allowing the belt, plate, or buckle to be
jammed in the door.
●Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belts cannot protect an occupant from death or serious injury.
●Ensure that the belt and plate are locked and the belt is not twisted.
If the seat belt does not function correctly, immediately contact your Toyota dealer.
●Replace the seat assembly, including the belts, if your vehicle has been
involved in a serious accident, even if there is no obvious damage.
●Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly, resulting in death or serious injury.
●Always make sure the shoulder belt passes through the guide when using the seat belt. Failure to properly position the belt may reduce the amount of protection in an accident and could lead to death or serious injury in a collision or sudden stop.
●Always make sure that the seat belt is not twisted, does not get caught in
the guide or the seatback and is arranged in the proper position.
74
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
■Using a seat belt extender
●Do not wear the seat belt extender if you can fasten the seat belt without
the extender.
●Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.
●The personalized extender may not be safe on another vehicle, when used by another person, or at a different seating position other than the one originally intended.
NOTICE
■When using a seat belt extender
When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.
75
1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel
The steering wheel can be adjusted to a comfortable position.
STEP 1
STEP 2
Hold the steering wheel and push the lever down.
Adjust to the ideal position by moving the steering wheel horizontally and vertically.
After adjustment, pull the lever up the steering wheel.
to secure
CAUTION
■Caution while driving
Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury.
■After adjusting the steering wheel
Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident, and resulting in death or serious injury.
76
1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror
Glare from the headlights of vehicles behind can be reduced by using the following functions: Manual anti-glare inside rear view mirror
Normal position Anti-glare position
Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.
Turns automatic mode on/off
The indicator comes on when automatic mode is turned on. Vehicles without a smart key system The mirror will revert to the automatic mode each time the engine switch is turned to the “ON” position. Vehicles with a smart key system The mirror will revert to the automatic mode each time the “ENGINE STOP” switch is turned to IGNITION ON mode.
START
77
1-3. Adjustable components (seats, mirrors, steering wheel)
Adjusting the height of rear view mirror
Adjust the height of the rear view mirror by moving it up and down.
■To prevent sensor error (vehicles with auto anti-glare inside rear view
mirror)
To ensure that the sensors operate prop- erly, do not touch or cover them.
CAUTION
■Caution while driving
Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.
78
1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors
Mirror angle can be adjusted using the switch.
STEP 1
STEP 2
To select a mirror to adjust, press the switch.
Left Right
To adjust the mirror, press the switch.
Up Right Down Left
Folding the mirrors
Push the mirror back in the direc- tion of the vehicle's rear.
79
1-3. Adjustable components (seats, mirrors, steering wheel)
■Mirror angle can be adjusted when
Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.
■When the mirrors are fogged up (vehicles with mirror defoggers)
Turn on the mirror defoggers to defog the mirrors. (→P. 240)
CAUTION
■When driving the vehicle
Observe the following precautions while driving. Failure to do so may result in loss of control of the vehicle and cause an accident, resulting in death or serious injury. ●Do not adjust the mirrors while driving. ●Do not drive with the mirrors folded. ●Both the driver and passenger side mirrors must be extended and properly
adjusted before driving. ■When a mirror is moving
To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.
■When the mirror defoggers are operating (vehicles with mirror defog-
gers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.
80
1
1-4. Opening and closing the windows and moon roof Power windows
The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows:
Closing One-touch closing (driver’s window only)* Opening One-touch opening (driver’s window only)*
*: Pressing
the switch
the opposite direction will stop win- dow travel partway.
in
Window lock switch
Press the switch down to lock the passenger window switches. Use this switch to prevent chil- dren from accidentally opening or closing a passenger window.
81
1-4. Opening and closing the windows and moon roof
■The power windows can be operated when
Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. ■Operating the power windows after turning the engine off
Vehicles without a smart key system The power windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They can- not, however, be operated once either front door is opened. Vehicles with a smart key system The power windows can be operated for approximately 45 seconds even after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. They cannot, however, be operated once either front door is opened.
■Jam protection function (driver’s window only)
If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.
■When the power window does not close normally (driver’s window
only) If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the driver’s door. ●Vehicles without a smart key system: After stopping the vehicle, the win- dow can be closed by holding the power window switch in the one-touch closing position while the engine switch is turned to the “ON” position.
●Vehicles with a smart key system: After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch clos- ing position while the “ENGINE START STOP” switch is turned to IGNI- TION ON mode.
●If the window still cannot be closed even by carrying out the operation explained above, initialize the function by performing the following proce- dure.
82
1
1-4. Opening and closing the windows and moon roof
STEP 1
STEP 2
STEP 3
Hold the power window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the win- dow has closed. Hold the power window switch in the one-touch opening position. Continue holding the switch for a further 2 seconds after the win- dow has opened completely. Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.
If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after perform- ing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
■Customization that can be configured at Toyota dealer
Settings (e.g. key linked operation) can be changed. (Customizable features: →P. 493)
CAUTION
■Closing the windows
Observe the following precautions. Failure to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body
in a position where it could be caught when a window is being operated.
●Do not allow children to operate the power windows.
Closing a power window on someone can cause serious injury, and in some instances, even death.
■Jam protection function (driver’s window only)
●Never use any part of your body to intentionally activate the jam protection
function.
●The jam protection function may not work if something gets caught just
before the window fully closes.
83
1-4. Opening and closing the windows and moon roof Moon roof∗
Use the overhead switches to open and close the moon roof and tilt it up and down. ■ Opening and closing
Opens the moon roof* The moon roof stops slightly before the fully open position to reduce wind noise. Press the switch again to fully open the moon roof. Closes the moon roof*
*: Lightly press the switch in either direction to stop the moon roof partway.
Tilts the moon roof up* Tilts the moon roof down*
*: Lightly press either of the moon roof switches to stop the moon roof partway.
■ Tilt up and down
84
∗: If equipped
1
1-4. Opening and closing the windows and moon roof
■The moon roof can be operated when Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.
■Operating the moon roof after turning the engine off
Vehicles without a smart key system The moon roof can be operated for approximately 45 seconds after the engine switch is turned to the “ACC” or “LOCK” position. It cannot, however, be operated once either front door is opened. Vehicles with a smart key system The moon roof can be operated for approximately 45 seconds after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. It cannot, however, be operated once either front door is opened.
■Jam protection function
If an object is detected between the moon roof and the frame while the moon roof is closing or tilting down, travel is stopped and the moon roof opens slightly.
■Sunshade
The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.
85
1-4. Opening and closing the windows and moon roof
■When the moon roof does not close normally
Perform the following procedure:
●If the moon roof closes but then re-opens slightly
STEP 1
STEP 2
STEP 3
STEP 2
STEP 3
STEP 4
Stop the vehicle.
Press and hold the “CLOSE” switch.*1
The moon roof will close, reopen and pause for approximately 10
seconds.*2 Then it will close again, tilt up and pause for approxi-
mately 1 second. Finally, it will tilt down, open and close.
Check to make sure that the moon roof is completely closed and
then release the switch.
●If the moon roof tilts down but then tilts back up
STEP 1
Stop the vehicle.
Press and hold the “UP” switch*1 until the moon roof moves into the
tilt up position and stops.
Release the “UP” switch once and then press and hold the “UP”
switch again.*1
The moon roof will pause for approximately 10 seconds in the tilt up
position.*2 Then it will adjust slightly and pause for approximately 1
second. Finally, it will tilt down, open and close.
Check to make sure that the moon roof is completely closed and
then release the switch.
*1: If the switch is released at the incorrect time, the procedure will have to
be performed again from the beginning.
*2: If the switch is released after the above mentioned 10 second pause, automatic operation will be disabled. In that case, press and hold the open/close switch in the close position or press and hold the “UP” switch. The moon roof will tilt up and pause for approximately 1 second. Then it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.
If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.
86
1
1-4. Opening and closing the windows and moon roof
■Moon roof open reminder function
Vehicles without a smart key system An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the engine switch off. Vehicles with a smart key system An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the “ENGINE START STOP” switch off.
■Customization that can be configured at Toyota dealer
Settings (e.g. key linked operation) can be changed. (Customizable features: →P. 493)
CAUTION
■Opening the moon roof
Observe the following precautions. Failure to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-
cle while it is moving.
●Do not sit on top of the moon roof.
■Closing the moon roof
Observe the following precautions. Failure to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their bod- ies in a position where they could be caught when the moon roof is being operated.
●Do not allow children to operate the moon roof.
Closing the moon roof on someone can cause death or serious injury.
■Jam protection function
●Never use any part of your body to intentionally activate the jam protection
function.
●The jam protection function may not work if something gets caught just
before the moon roof fully closes.
87
1-5. Refueling Opening the fuel tank cap
Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicle
Vehicles without a smart key system Turn the engine switch off and ensure that all the doors and win- dows are closed. Vehicles with a smart key system Turn the “ENGINE START STOP” switch off and ensure that all the doors and windows are closed.
■ Opening the fuel tank cap
STEP 1
Pull up the opener to open the fuel filler door.
STEP 2
Turn the fuel tank cap slowly to open.
88
1-5. Refueling
STEP 3
Hang the fuel tank cap on the back of the fuel filler door.
Closing the fuel tank cap