2012 Toyota Camry Owners Manual

■The seat heaters can be used when

Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.

■When not in use

Move the dial fully backward. The indicator light turns off.

∗: If equipped 307

3-5. Other interior features

CAUTION

■Burns

●Use caution when seating the following persons in a seat with the seat

heater on to avoid the possibility of burns: • Babies, small children, the elderly, the sick and the physically chal-

lenged

• Persons with sensitive skin • Persons who are fatigued • Persons who have taken alcohol or drugs that induce sleep (sleeping

drugs, cold remedies, etc.)

●Do not cover the seat with anything when using the seat heater.

Using the seat heater with a blanket or cushion increases the temperature of the seat and may lead to overheating.

●Do not use the seat heater more than necessary. Doing so may cause

minor burns or overheating.

NOTICE

■To prevent seat heater damage

Do not put heavy objects that have an uneven surface on the seat and do not stick sharp objects (needles, nails, etc.) into the seat.

■To prevent battery discharge

Turn the seat heaters off when the engine is not running.

308

3-5. Other interior features Armrest

Fold down the armrest for use.

NOTICE

■To prevent damage to the armrest

Do not apply too much load on the armrest.

309

3-5. Other interior features Coat hooks

CAUTION

■Items that cannot be hung on the coat hook

Do not hang coat hangers or other hard or sharp objects on the hook. If the SRS curtain shield airbags deploy, these items may become projectiles, causing death or serious injury.

310

3-5. Other interior features Floor mat

Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet.

STEP 1

STEP 2

the

Insert retaining hooks (clips) into the floor mat eye- lets.

Turn the upper knob of each retaining hook (clip) to secure the floor mats in place. *: Always align the ∆ marks.

The shape of the retaining hooks (clips) may differ from that shown in the illustration.

311

3-5. Other interior features

CAUTION

Observe the following precautions. Failure to do so may cause the driver's floor mat to slip, possibly interfering with the pedals while driving. An unexpectedly high speed may result or it may become difficult to stop the vehicle, leading to a serious accident. ■When installing the driver's floor mat

●Do not use floor mats designed for other models or different model year

vehicles, even if they are Toyota Genuine floor mats.

●Only use floor mats designed for the driver's seat. ●Always install the floor mat securely using the retaining hooks (clips) pro-

vided.

●Do not use two or more floor mats on top of each other. ●Do not place the floor mat bottom-side up or upside-down.

■Before driving

●Check that the floor mat is securely fixed in the correct place with all the provided retaining hooks (clips). Be especially careful to perform this check after cleaning the floor.

●With the engine stopped and the shift lever in P, fully depress each pedal to the floor to make sure it does not inter- fere with the floor mat.

312

3-5. Other interior features Trunk features

■ Grocery bag hooks

313

3-5. Other interior features

■ Cargo net (if equipped)

NOTICE

■To prevent damage to the hooks

Do not apply too much load to the hooks.

314

3-5. Other interior features Garage door opener∗

The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, secu- rity systems, and other devices.

The garage door opener (HomeLink® Universal Transceiver) is manufac- tured under license from HomeLink®.

Programming HomeLink® (for U.S. owners)

The HomeLink® compatible transceiver in your vehicle has 3 buttons which can be programmed to operate 3 different devices. Refer to the programming method below appropriate for the device.

Buttons Indicator

∗: If equipped 315

Point the remote control trans- mitter for the device 1 to 3 in. (25
to 75 mm) from the HomeLink® control buttons.

Keep the HomeLink® indicator light in view while programming.

the Press and hold one of HomeLink® buttons and the the transmitter button. When HomeLink® light changes from a slow to a rapid flash, you can release both but- tons.

indicator

If the HomeLink® indicator light comes on but does not flash, or flashes rapidly for 2 seconds and remains lit, the HomeLink® button is already programmed. Use the other buttons or the “Reprogramming a HomeLink® button” instructions. (→P. 319)

follow

3-5. Other interior features

■ Programming the HomeLink® STEP 1

STEP 2

316

STEP 3

3-5. Other interior features

Test the HomeLink® operation by pressing the newly pro- grammed button.

If a HomeLink® button has been programmed for a garage door, check to see if the garage door opens and closes. If the garage door does not operate, see if your remote control transmitter is of the rolling code type. Press and hold the programmed HomeLink® button. The remote control trans- mitter is of the rolling code type if the HomeLink® light flashes rapidly for 2 seconds and then remains lit. If your transmit- ter is of the rolling code type, pro- ceed heading “Programming a rolling code sys- tem”.

indicator

the

to

STEP 4

Repeat the steps above to program another device for any of the remaining HomeLink® buttons.

■ Programming a Rolling Code system (for U.S. owners)

If your device is Rolling Code equipped, follow the steps under the heading “Programming HomeLink®” before proceeding with the steps listed below.

STEP 1

STEP 2

Locate the learn button on the ceiling mounted garage door opener motor. The exact location and color of the button may vary by brand of garage door opener motor. Refer to the operation manual supplied with the garage door opener motor for the location of the learn button. Press the learn button. Following this step, you have 30 seconds in which to initiate step 3
below.

317

3-5. Other interior features

STEP 3

STEP 4

Press and hold the vehicle’s programmed HomeLink® button for 2 seconds and then release it. Repeat this step once again. The garage door may open. If the garage door opens, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door. The ceiling mounted garage door opener motor should now recog- nize the HomeLink® signal and operate the garage door. Repeat the steps above to program another rolling code sys- tem for any of the remaining HomeLink® buttons.

■ Programming an entry gate (for U.S. owners)/Programming a

device in the Canadian market

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

STEP 6

Place the remote control transmitter 1 to 3 in. (25 to 75 mm) away from the HomeLink® buttons. Keep the HomeLink® indicator light in view while programming. Press and hold the selected HomeLink® button. Repeatedly press and release (cycle) the remote control transmitter for 2 seconds each until step 4 is completed. When the HomeLink® indicator light starts to flash rapidly, release the buttons. Test the HomeLink® operation by pressing the newly pro- grammed button. Check to see if the gate/device operates correctly. Repeat the steps above to program another device for any of the remaining HomeLink® buttons.

■ Programming other devices

To program other devices such as home security systems, home door locks or lighting, contact your Toyota dealer for assistance.

■ Reprogramming a button

The individual HomeLink® buttons cannot be erased but can be reprogrammed. To reprogram a button, follow the “Reprogramming a HomeLink® button” instructions.

318

3-5. Other interior features

Operating HomeLink®

Press the appropriate HomeLink® button. The HomeLink® indicator light should come on.

The HomeLink® compatible transceiver in your vehicle continues to send a signal for up to 20 seconds as long as the button is pressed.

Reprogramming a HomeLink® button

Press and hold the desired HomeLink® button. After 20 seconds, the HomeLink® indicator light will start flashing slowly. Keep pressing the HomeLink® button and press and hold the transmitter button until the HomeLink® indicator light changes from a slow to a rapid flash. Release the buttons.

Erasing the entire HomeLink® memory (all three programs)

Press and hold the 2 outside but- tons for 10 seconds until the indi- cator light flashes.

If you sell your vehicle, be sure to erase the programs stored in the HomeLink® memory.

319

3-5. Other interior features

■Before programming

●Install a new battery in the remote control transmitter. ●The battery side of the remote control transmitter must be pointed away

from the HomeLink® button. ■To prevent battery discharge

Vehicles without a smart key system: HomeLink® will turn off if a door has not been opened and closed for 20 min- utes or the engine switch is left turned off. (After which programming cannot be completed.) Open and close a door or turn the engine switch to the “ACC” position to turn HomeLink® on. We recommend programming while the engine switch is in the “ACC” position. Vehicles with a smart key system: HomeLink® will turn off if a door has not been opened and closed for 20 min- utes or the “ENGINE START STOP” switch is left turned off. (After which pro- gramming cannot be completed.) Open and close a door or turn the “ENGINE START STOP” switch to ACCESSORY mode to turn HomeLink® on. We recommend programming while the “ENGINE START STOP” switch is in ACCESSORY mode.

■Certification for the garage door opener

U.S.A. FCC ID: CB2051AHL4/CB251AHL4NR NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

320

3-5. Other interior features

■When support is necessary

Visit on the web at www.homelink.com or call 1-800-355-3515.

CAUTION

■When programming a garage door or other remote control devices

The garage door or other devices may operate, so ensure people and objects are out of danger to prevent potential harm.

■Conforming to federal safety standards

Do not use the HomeLink® compatible transceiver with any garage door opener or device that lacks safety stop and reverse features as required by federal safety standards. This includes any garage door that cannot detect an interfering object. A door or device without these features increases the risk of death or serious injury.

321

3-5. Other interior features Compass∗

The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation

To turn the compass on or off, press “AUTO” for more than 3
seconds.

■ Displays and directions

Display

NE SE SW NW

Direction

North

Northeast

East

Southeast

South

Southwest

West

Northwest

322

∗: If equipped

3-5. Other interior features

Calibrating the compass

The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies depending on the geographic position of the vehicle.

If you cross over one of the map boundaries shown in illustration, the compass will deviate. To obtain higher precision or perfect calibration, refer to “Deviation calibra- tion”.

■ Deviation calibration Stop the vehicle. STEP 1

STEP 2

Press and hold “AUTO”. A number (1 to 15) appears on the compass display.

323

3-5. Other interior features

STEP 3

Referring to the map above, press “AUTO” to select the num- ber of the zone you are in. If the direction is displayed several seconds after adjustment, the calibration is complete.

■ Circling calibration

When “C” appears on the dis- play, drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed.

If there is not enough space to drive in a circle, drive around the block until a direction is dis- played.

■Conditions unfavorable to correct operation

The compass may not show the correct direction in the following conditions: ●The vehicle is stopped immediately after turning. ●The vehicle is on an inclined surface. ●The vehicle is in a place where the earth's magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.).

●The vehicle has become magnetized.

(There is a magnet or metal object near the inside rear view mirror.)

●The battery has been disconnected. ●A door is open.

324

3-5. Other interior features

CAUTION

■While driving the vehicle

Do not adjust the display. Adjust the display only when the vehicle is stopped.

■When doing the circling calibration

Secure a wide space, and watch out for people and vehicles in the vicinity. Do not violate any local traffic rules while performing circling calibration.

NOTICE

■To avoid compass malfunctions

Do not place magnets or any metal objects near the inside rear view mirror. Doing this may cause the compass sensor to malfunction.

■To ensure normal operation of the compass

●Do not perform a circling calibration of the compass in a place where the earth's magnetic field is subject to interference by artificial magnetic fields. ●During calibration, do not operate electric systems (moon roof, power win-

dows, etc.) as they may interfere with the calibration.

325

3-5. Other interior features Safety Connect∗

Safety Connect is a subscription-based telematics service that uses Global Positioning System (GPS) data and embedded cellular tech- nology to provide safety and security features to subscribers. Safety Connect is supported by Toyota’s designated response center, which operates 24 hours per day, 7 days per week. Safety Connect service is available by subscription on select, telematics hardware-equipped vehicles. By using the Safety Connect service, you are agreeing to be bound by the Telematics Subscription Service Agreement and its Terms and Conditions, as in effect and amended from time to time, a current copy of which is available at Toyota.com. All use of the Safety Con- nect service is subject to such then-applicable Terms and Condi- tions. ■ System components

Microphone LED light indicators “SOS” button

326

∗: if equipped

3-5. Other interior features

■ Services

Subscribers have the following Safety Connect services avail- able: ● Automatic Collision Notification*

Helps drivers receive necessary response from emergency service providers. (→P. 329) *: U.S. Patent No. 7,508,298 B2

● Stolen Vehicle Location

Helps drivers in the event of vehicle theft. (→P. 330)

● Emergency Assistance Button (SOS)

Connects drivers to response-center support. (→P. 330)

● Enhanced Roadside Assistance

Provides drivers various on-road assistance. (→P. 330)

■ Subscription

After you have signed the Telematics Subscription Service Agreement and are enrolled, you can begin receiving services. A variety of subscription terms is available for purchase. Contact your Toyota dealer, call 1-800-331-4331, or push the “SOS” but- ton in your vehicle for further subscription details.

327

3-5. Other interior features

■Safety Connect Services Information

●Phone calls using the vehicles Bluetooth® technology will not be possible

during Safety Connect.

●Safety Connect is available beginning Fall 2009 on select Toyota models. Contact with the Safety Connect response center is dependent upon the telematics device being in operative condition, cellular connection avail- ability, and GPS satellite signal reception, which can limit the ability to reach the response center or receive emergency service support. Enroll- ment and Telematics Subscription Service Agreement required. A variety of subscription terms is available; charges vary by subscription term selected.

●Automatic Collision Notification, Emergency Assistance, Stolen Vehicle Location, and Enhanced Roadside Assistance will function in the United States, including Hawaii and Alaska, and in Canada. No Safety Connect services will function outside of the United States in countries other than Canada.

●Safety Connect services are not subject to section 255 of the Telecom-

munications Act and the device is not TTY compatible.

■Languages

The Safety Connect response center will offer support in multiple languages. The Safety Connect system will offer voice prompts in English and Spanish. Please indicate your language of choice when enrolling.

■When contacting the response center

You may be unable to contact the response center if the network is busy.

328

3-5. Other interior features

Safety Connect LED light Indicators

When the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key system) or the engine switch is turned to the “ON” position (vehicles without a smart key system), the red indicator light comes on for 2 seconds then turns off. Afterward, the green indicator light comes on, indicating that the service is active. The following indicator light patterns indicate specific system usage conditions: ● Green indicator light on = Active service ● Green indicator light flashing = Safety Connect call in process ● Red indicator light (except at vehicle start-up) = System malfunc-

tion (contact your Toyota dealer)

● No indicator light (off) = Safety Connect service not active

Safety Connect services

■ Automatic Collision Notification

In case of either airbag deployment or severe rear-end collision, the system is designed to automatically call the response center. The responding agent receives the vehicle’s location and attempts to speak with the vehicle occupants to assess the level of emer- gency. If the occupants are unable to communicate, the agent automatically treats the call as an emergency, contacts the nearest emergency services provider to describe the situation, and requests that assistance be sent to the location.

329

3-5. Other interior features

■ Stolen Vehicle Location

If your vehicle is stolen, Safety Connect can work with local author- ities to assist them in locating and recovering the vehicle. After fil- ing a police report, call the Safety Connect response center at 1- 800-331-4331 and follow the prompts for Safety Connect to initiate this service. In addition to assisting law enforcement with recovery of a stolen vehicle, Safety-Connect-equipped vehicle location data may, under certain circumstances, be shared with third parties to locate your vehicle. Further information is available at Toyota.com.

■ Emergency Assistance Button (“SOS”)

In the event of an emergency on the road, push the “SOS” button to reach the Safety Connect response center. The answering agent will determine your vehicle’s location, assess the emer- gency, and dispatch the necessary assistance required. If you accidentally press the “SOS” button, tell the response-center agent that you are not experiencing an emergency.

■ Enhanced Roadside Assistance

Enhanced Roadside Assistance adds GPS data to the already included warranty-based Toyota roadside service. Subscribers can press the “SOS” button to reach a Safety Connect response-center agent, who can help with a wide range of needs, such as: towing, flat tire, fuel delivery, etc. For a description of the Enhanced Roadside Assistance services and their limitations, please see the Safety Connect Terms and Conditions, which are available at Toyota.com.

330

3-5. Other interior features

Safety information for Safety Connect

Important! Read this information before using Safety Connect. ■ Exposure to radio frequency signals

The Safety Connect system installed in your vehicle is a low-power radio transmitter and receiver. It receives and also sends out radio frequency (RF) signals. In August 1996, the Federal Communications Commission (FCC) adopted RF exposure guidelines with safety levels for mobile wire- less phones. Those guidelines are consistent with the safety stan- dards previously set by the following U.S. and international standards bodies. ● ANSI (American National Standards Institute) C95.1 [1992] ● NCRP (National Council on Radiation Protection and Measure-

ment) Report 86 [1986]

● ICNIRP (International Commission on Non-Ionizing Radiation

Protection) [1996]

Those standards were based on comprehensive and periodic eval- uations of the relevant scientific literature. Over 120 scientists, engineers, and physicians from universities, and government health agencies and industries reviewed the available body of research to develop the ANSI Standard (C95.1). The design of Safety Connect complies with the FCC guidelines in addition to those standards.

331

3-5. Other interior features

■Certification for Safety Connect

FCC ID: O9EGTM1
FCC ID: O6Y-CDMRF101
NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

332

4-1. Maintenance and care Cleaning and protecting the vehicle exterior

Perform the following to protect the vehicle and maintain it in prime condition:

● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.

● Wash the vehicle body using a sponge or soft cloth, such as a

chamois.

● For hard-to-remove marks, use car wash soap and rinse thor-

oughly with water.

● Wipe away any water. ● Wax the vehicle when the waterproof coating deteriorates. If water does not bead on a clean surface, apply wax when the vehicle body is cool.

■Automatic car washes

●Fold the mirrors before washing the vehicle. Start washing from the front

of the vehicle. Make sure to extend the mirrors before driving.

●Brushes used in automatic car washes may scratch the vehicle surface

and harm your vehicle’s paint.

●Vehicles with rear spoiler: In certain automatic car washes, the rear spoiler may interfere with machine operation. This may prevent the vehi- cle from being cleaned properly or result in damage to the rear spoiler.

■High pressure car washes

●Do not allow the nozzles of the car wash to come within close proximity

of the windows.

●Before using the car wash, check that the fuel filler door on your vehicle

is closed properly.

334

4-1. Maintenance and care

■When using a car wash (vehicles with a smart key system)

If the door handle becomes wet while the electronic key is within the effec- tive range, the door may lock and unlock repeatedly. In that case, follow the following correction procedures to wash the vehicle: ●Place the electronic key in a location 6 ft. (2 m) or more away from the

vehicle. (Take care to ensure that the key is not stolen.)

●Set the electronic key to battery-saving mode to disable the smart key

system. (→P. 39)

■Aluminum wheels (if equipped)

●Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint.

●Do not use detergent on the wheels when they are hot, for example after

driving for long distance in the hot weather.

●Wash detergent from the wheels immediately after use.

■Bumpers

Do not scrub with abrasive cleaners.

CAUTION

■When washing the vehicle

Do not apply water to the inside of the engine compartment. Doing so may cause the electrical components etc. to catch fire.

■Precautions regarding the exhaust pipe

Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.

■ Precaution regarding the Blind Spot Monitor

If the paint of the rear bumper is chipped or scratched, the system may mal- function. If this occurs, consult your Toyota dealer.

335

4-1. Maintenance and care

NOTICE

■To prevent paint deterioration and corrosion on the body and compo-

nents (aluminum wheels etc.) ●Wash the vehicle immediately in the following cases:

• After driving near the sea coast • After driving on salted roads • If coal tar or tree sap is present on the paint surface • If dead insects, insect droppings or bird droppings are present on the

paint surface

• After driving in an area contaminated with soot, oily smoke, mine dust,

iron powder or chemical substances

• If the vehicle becomes heavily soiled with dust or mud • If liquids such as benzene and gasoline are spilled on the paint surface

●If the paint is chipped or scratched, have it repaired immediately. ●To prevent the wheels from corroding, remove any dirt and store in a place

with low humidity when storing the wheels.

■Cleaning the exterior lights

●Wash carefully. Do not use organic substances or scrub with a hard brush.

This may damage the surfaces of the lights.

●Do not apply wax to the surfaces of the lights.

Wax may cause damage to the lenses.

336

4-1. Maintenance and care Cleaning and protecting the vehicle interior

The following procedures will help protect your vehicle's interior and keep it in top condition: ■ Protecting the vehicle interior

Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.

■ Cleaning the leather areas

● Remove dirt and dust using a vacuum cleaner. ● Wipe off any excess dirt and dust with a soft cloth dampened

with diluted detergent. Use a diluted water solution of approximately 5% neutral wool deter- gent.

● Wring out any excess water from the cloth and thoroughly

wipe off all remaining traces of detergent.

● Wipe the surface with a dry, soft cloth to remove any remain- ing moisture. Allow the leather to dry in a shaded and venti- lated area.

■ Cleaning the synthetic leather areas

● Remove loose dirt using a vacuum cleaner. ● Apply a mild soap solution to the synthetic leather using a

sponge or soft cloth.

● Allow the solution to soak in for a few minutes. Remove the

dirt and wipe off the solution with a clean, damp cloth.

337

4-1. Maintenance and care

■Caring for leather areas

Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle's interior.

■Shampooing the carpets

There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not use water. Wipe dirty surfaces and let them dry. Excellent results are obtained by keeping the carpet as dry as possible.

■Seat belts

Clean with mild soap and lukewarm water using a cloth or sponge. Also check the belts periodically for excessive wear, fraying or cuts.

CAUTION

■Water in the vehicle

●Do not splash or spill liquid in the vehicle.

Doing so may cause electrical components etc. to malfunction or catch fire.

●Do not get any of the SRS components or wiring in the vehicle interior wet.

(→P. 101) An electrical malfunction may cause the airbags to deploy or not function properly, resulting in death or serious injury.

■Cleaning the interior (especially instrument panel)

Do not use polish wax or polish cleaner. The instrument panel may reflect off the windshield, obstructing the driver's view and leading to an accident, resulting in death or serious injury.

338

4-1. Maintenance and care

NOTICE

■Cleaning detergents

●Do not use the following types of detergent, as they may discolor the vehi-

cle interior or cause streaks or damage to painted surfaces: • Non-seat portions: Organic substances such as benzene or gasoline,

alkaline or acidic solutions, dye, and bleach

• Seats: Alkaline or acidic solutions, such as thinner, benzene, and alco-

hol

●Do not use polish wax or polish cleaner. The instrument panel's or other

interior part’s painted surface may be damaged.

■Preventing damage to leather surfaces

Observe the following precautions to avoid damage to and deterioration of leather surfaces: ●Remove any dust or dirt from leather surfaces immediately. ●Do not expose the vehicle to direct sunlight for extended periods of time.

Park the vehicle in the shade, especially during summer.

●Do not place items made of vinyl, plastic, or containing wax on the uphol- stery, as they may stick to the leather surface if the vehicle interior heats up significantly.

■Water on the floor

Do not wash the vehicle floor with water. Vehicle systems such as the audio system may be damaged if water comes into contact with electrical components such as the audio system above or under the floor of the vehicle. Water may also cause the body to rust.

■Cleaning the inside of the rear window

●Do not use glass cleaner to clean the rear window, as this may cause damage to the rear window defogger heater wires or antenna. Use a cloth dampened with lukewarm water to gently wipe the window clean. Wipe the window in strokes running parallel to the heater wires or antenna. ●Be careful not to scratch or damage the heater wires or antenna.

339

4-2. Maintenance Maintenance requirements

To ensure safe and economical driving, day-to-day care and regular maintenance are essential. It is the owner’s responsibility to perform regular checks. Toyota recommends performing the following main- tenance: ■ General maintenance

General maintenance should be performed on a daily basis. This can be done by yourself or by a Toyota dealer.

■ Scheduled maintenance

Scheduled maintenance should be performed at specified inter- vals according to the maintenance schedule. For details about maintenance items and schedules, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

■ Do-it-yourself maintenance

You can perform some maintenance procedures by yourself. Please be aware that do-it-yourself maintenance may affect war- ranty coverage. The use of Toyota Repair Manuals is recommended. For details about warranty coverage, see the separate “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement”.

■Repair and replacement

It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.

■Reset the maintenance data (U.S.A. only)

After the required maintenance is performed according to the maintenance schedule, please reset the maintenance data. To reset the data, follow the procedures described below:

340

4-2. Maintenance

STEP 1

STEP 2

STEP 3

Turn the engine switch (vehicles without a smart key system) or the “ENGINE START STOP” switch (vehicles with a smart key system) off with the trip meter A reading shown. (→P. 172) While pressing the display change button (→P. 169), turn the engine switch to the “ON” position (vehicles without a smart key system) or “ENGINE START STOP” switch to IGNITION ON mode (vehicles with a smart key system) Continue to press and hold the knob until the trip meter displays “000000”.

■Allow inspection and repairs to be performed by a Toyota dealer

●Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.

●Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.

CAUTION

■If your vehicle is not properly maintained

Improper maintenance could result in serious damage to the vehicle and possible serious injury or death.

■Handling of the battery

●Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.

●Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.

●Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (→P. 363)

341

4-2. Maintenance General maintenance

Listed below are the general maintenance items that should be per- formed at the intervals specified in the “Owner's Warranty Informa- tion Booklet” or “Owner’s Manual Supplement/Scheduled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice.

Check points Check the connections.

(→P. 360)

(→P. 363) Is the brake fluid at the correct level? (→P. 361) Is the engine coolant at the correct level? Is the engine oil at the correct level? There should not be any fumes or strange sounds. The radiator and condenser should be free from foreign objects. (→P. 361) Is there sufficient washer fluid? (→P. 366)

(→P. 355)

Engine compartment

Items

Battery

Brake fluid

Engine coolant

Engine oil

Exhaust system

Radiator/condenser

Washer fluid

342

4-2. Maintenance

Vehicle interior

Items

Check points

Accelerator pedal

Automatic transmission “Park” mechanism

Brake pedal

Brakes

Head restraints (front seat)

Indicators/buzzers

Lights

Parking brake

• The accelerator pedal should move smoothly (without uneven pedal effort or catching). • When parked on a slope and the shift lever is in P, is the vehicle securely stopped? • Does the brake pedal move smoothly? • Does the brake pedal have appro- priate clearance from the floor? (→P. 473) • Does the brake pedal have the correct amount of free play? (→P. 473) • The vehicle should not pull to one side when the brakes are applied. • The brakes should work effec- tively. • The brake pedal should not feel spongy. • The brake pedal should not get too close to the floor when the brakes are applied. • Do the head restraints move smoothly and lock securely? • Do the indicators and buzzers function properly? • Do all the lights come on? • Does the parking brake pedal move smoothly? • When parked on a slope and the parking brake is on, is the vehicle securely stopped?

343

4-2. Maintenance

Items

Check points

Seat belts

Seats

Steering wheel

• Do the seat belts operate smoothly? • The seat belts should not be dam- aged. • Do the seat controls operate properly? • Does the steering wheel rotate smoothly? • Does the steering wheel have the correct amount of free play? • There should not be any strange sounds coming from the steering wheel.

344

4-2. Maintenance

Vehicle exterior

Items

Check points

Doors/trunk

Engine hood

Fluid leaks

Tires

• Do the doors and trunk operate smoothly? • Does the engine hood lock sys- tem work properly? • There should not be any signs of fluid leakage after the vehicle has been parked. • Is the tire inflation pressure cor- rect? • The tires should not be dam- aged or excessively worn. • Have the tires been rotated according to the maintenance schedule? • The wheel nuts should not be loose.

CAUTION

■If the engine is running

Turn the engine off and ensure that there is adequate ventilation before per- forming maintenance checks.

345

4-2. Maintenance Emission inspection and maintenance (I/M) programs

Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system moni- tors the operation of the emission control system. ■ If the malfunction indicator lamp comes on

The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle.

■ Your vehicle may not pass the I/M test in the following situa-

tions: ● When the battery is disconnected or discharged

Readiness codes that are set during ordinary driving are erased. Also, depending on your driving habits, the readiness codes may not be completely set.

● When the fuel tank cap is loose

The malfunction indicator lamp comes on indicating a tempo- rary malfunction and your vehicle may not pass the I/M test.

■ When the malfunction indicator lamp still remains on after

several driving trips The error code in the OBD system will not be cleared unless the vehicle is driven 40 or more times.

■ If your vehicle does not pass the I/M test

Contact your Toyota dealer to prepare the vehicle for re-testing.

346

4-3. Do-it-yourself maintenance Do-it-yourself service precautions

If you perform maintenance by yourself, be sure to follow the correct procedures as given in these sections.

Items

Parts and tools

Battery condition

(→P. 363)

Brake fluid level

(→P. 361)

Engine coolant level

(→P. 360)

• Warm water • Baking soda • Grease • Conventional wrench (for terminal clamp bolts) • FMVSS No.116 DOT 3 or SAE J1703 brake fluid • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol-based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology U.S.A.: “Toyota Super Long Life Coolant” is pre-mixed with 50% coolant and 50% deionized water. Canada: “Toyota Super Long Life Coolant” is pre-mixed with 55% coolant and 45% deionized water. • Funnel (used only for adding engine coolant)

347

4-3. Do-it-yourself maintenance

Items

Parts and tools

Engine oil level

(→P. 355)

Fuses

(→P. 389)

Light bulbs

(→P. 401)

Radiator and condenser

(→P. 361)

Tire inflation pressure (→P. 375)

Washer fluid

(→P. 366)

• “Toyota Genuine Motor Oil” or equivalent • Rag or paper towel • Funnel (used only for adding engine oil) • Fuse with same amperage rating as original • Bulb with same number and watt- age rating as original • Phillips-head screwdriver • Flathead screwdriver • Wrench

⎯

• Tire pressure gauge • Compressed air source • Water or washer fluid containing antifreeze (for winter use) • Funnel (used only for adding water or washer fluid)

348

4-3. Do-it-yourself maintenance

CAUTION

The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions: ■When working on the engine compartment:

●Keep hands, clothing and tools away from the moving fan and engine

drive belt.

●Be careful not to touch the engine, radiator, exhaust manifold, etc. right

after driving as they may be hot. Oil and other fluids may also be hot.

●Do not leave anything that may burn easily, such as paper or rags, in the

engine compartment.

●Do not smoke, cause sparks or expose an open flame to fuel or the bat-

tery. Fuel and battery fumes are flammable.

●Be extremely cautious when working on the battery. It contains poisonous

and corrosive sulfuric acid.

■When working near the electric cooling fans or radiator grille

Vehicles without a smart key system: Be sure the engine switch is off. With the engine switch in the “ON” position, the electric cooling fans may auto- matically start to run if the air conditioning is on and/or the coolant tempera- ture is high. (→P. 361) Vehicles with a smart key system: Be sure the “ENGINE START STOP” switch is off. With the “ENGINE START STOP” switch in IGNITION ON mode, the electric cooling fans may automatically start to run if the air condi- tioning is on and/or the coolant temperature is high. (→P. 361)

■Safety glasses

Wear safety glasses to prevent flying or falling material, fluid spray, etc. from getting in your eyes.

NOTICE

■If you remove the air cleaner filter

Driving with the air cleaner filter removed may cause excessive engine wear due to dirt in the air. Also, a backfire could cause a fire in the engine com- partment.

349

4-3. Do-it-yourself maintenance Hood

Release the lock from the inside of the vehicle to open the hood.

STEP 1

STEP 2

Pull the hood release lever. The hood will pop up slightly.

Pull up the auxiliary catch lever and lift the hood.

CAUTION

■Pre-driving check

Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.

350

4-3. Do-it-yourself maintenance Positioning a floor jack

When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury. ■ Front

■ Rear 2.5 L 4-cylinder (2AR-FE) engine

CTY43AV171

3.5 L V6 (2GR-FE) engine

351

4-3. Do-it-yourself maintenance

CAUTION

■When raising your vehicle

Make sure to observe the following precautions to reduce the possibility of death or serious injury:

●Lift up the vehicle using a floor jack such as the one shown in the illustra- tion.

●When using a floor jack, follow the instructions of the manual provided with

the jack.

●Do not use the jack that was supplied with your vehicle. ●Do not put any part of your body underneath the vehicle when it is sup-

ported only by the floor jack.

●Always use floor jack and/or automotive jack stands on a solid, flat, level

surface.

●Do not start the engine while the vehicle is supported by the floor jack. ●Stop the vehicle on level, firm ground, firmly set the parking brake and shift

the shift lever to P.

●Make sure to set the floor jack properly at the jack point.

Raising the vehicle with an improperly positioned floor jack will damage the vehicle and may cause the vehicle to fall off the floor jack.

●Do not raise the vehicle while someone is in the vehicle. ●When raising the vehicle, do not place any objects on top of or underneath

the floor jack.

352

4-3. Do-it-yourself maintenance Engine compartment

2.5 L 4-cylinder (2AR-FE) engine

Engine oil filler cap

(→P. 357)

Engine oil level dipstick

(→P. 355)

Brake fluid reservoir

Fuse box

(→P. 361) (→P. 389)

(→P. 363) (→P. 361)

Battery Radiator Electric cooling fans Condenser Engine coolant reservoir

(→P. 361)

(→P. 360) Washer fluid tank (→P. 366)

353

4-3. Do-it-yourself maintenance

3.5 L V6 (2GR-FE) engine

Engine oil filler cap

(→P. 357)

Engine oil level dipstick

(→P. 355)

Brake fluid reservoir

Fuse box

(→P. 361) (→P. 389)

354

(→P. 363) (→P. 361)

Battery Radiator Electric cooling fans Condenser Engine coolant reservoir

(→P. 361)

(→P. 360) Washer fluid tank (→P. 366)

4-3. Do-it-yourself maintenance

Engine oil

With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil STEP 1

Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine. Hold a rag under the end, pull the dipstick out.

STEP 2

2.5 L 4-cylinder (2AR-FE) engine

3.5 L V6 (2GR-FE) engine

STEP 3

STEP 4

STEP 5

STEP 6

Wipe the dipstick clean. Reinsert the dipstick fully. Holding a rag under the end, pull the dipstick out and check the oil level. Wipe the dipstick and reinsert it fully.

355

4-3. Do-it-yourself maintenance

2.5 L 4-cylinder (2AR-FE) engine

3.5 L V6 (2GR-FE) engine

Low Full

Low Full

356

■ Adding engine oil

4-3. Do-it-yourself maintenance

If the oil level is below or near the low level mark, add engine oil of the same type as that already in the engine.

Make sure to check the oil type and prepare the items needed before adding oil.

Engine oil selection →P. 469
Oil quantity (Low → Full) Items

Clean funnel

1.6 qt. (1.5 L, 1.3 lmp. qt.)

STEP 1

STEP 2

STEP 3

Remove the oil filler cap by turning it counterclockwise. Add engine oil slowly, checking the dipstick. Install the oil filler cap by turning it clockwise.

357

4-3. Do-it-yourself maintenance

■Engine oil consumption

●The amount of engine oil consumed depends on the oil viscosity, the

quality of the oil and the way the vehicle is driven.

●More oil is consumed under driving conditions such as high speeds and

frequent acceleration and deceleration.

●A new engine consumes more oil. ●When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accu- rately.

●Oil consumption: Max. 1.1 qt./600 miles (0.9 Imp. qt./600 miles, 1.0 L/

1000 km)

●If your vehicle consumes more than 1.1 qt. (1.0 L, 0.9 Imp. qt.) every 600

miles (1000 km), contact your Toyota dealer.

CAUTION

■Used engine oil

●Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation or skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.

●Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.

●Do not leave used engine oil within the reach of children.

358

4-3. Do-it-yourself maintenance

NOTICE

■To prevent serious engine damage Check the oil level on a regular basis.

■When replacing the engine oil

●Be careful not to spill engine oil on the vehicle components. ●Avoid overfilling, as the engine could be damaged. ●Check the oil level on the dipstick every time you refill the vehicle. ●Be sure the engine oil filler cap is properly tightened.

359

4-3. Do-it-yourself maintenance

Engine coolant

The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir when the engine is cold.

Reservoir cap “F” line “L” line If the level is on or below the “L” line, add coolant up to the “F” line. (→P. 459)

■Coolant selection

Only use “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology.

U.S.A.:

“Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deionized water. (Minimum temperature: -31°F [-35°C]) Canada: “Toyota Super Long Life Coolant” is a mixture of 55% coolant and 45% deionized water. (Minimum temperature: -44°F [-42°C])

For more details about engine coolant, contact your Toyota dealer.

■If the coolant level drops within a short time of replenishing