2012 Toyota Camry Owners Manual

TABLE OF CONTENTS

1 Before driving

Adjusting and operating features such as door locks, mirrors, and steering column.

2 When driving

Driving, stopping and safe-driving information.

3 Interior fea-

tures

Air conditioning and audio systems, as well as other in- terior features for a comfortable driving experience.

4 Maintenance

and care

Cleaning and protecting your vehicle, performing do-it- yourself maintenance, and maintenance information.

5 When trouble

arises

What to do if the vehicle needs to be towed, gets a flat tire, or is involved in an accident.

6 Vehicle

specifications

Detailed vehicle information.

7 For owners

Reporting safety defects for U.S. owners, and seat belt and SRS airbag instructions for Canadian owners

Index

Alphabetical listing of information contained in this manual.

For your information

Main Owner’s Manual

Please note that this manual covers all models and all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle. All specifications provided in this manual are current at the time of printing. However, because of the Toyota policy of continual product improvement, we reserve the right to make changes at any time without notice. Depending on specifications, the vehicle shown in the illustrations may differ from your vehicle in terms of equipment.

Noise from under vehicle after turning off the engine

Approximately five hours after the engine is turned off, you may hear sound coming from under the vehicle for several minutes. This is the sound of a fuel evaporation leakage check and, it does not indicate a malfunction.

Accessories, spare parts and modification of your Toyota

is not responsible

these products and

A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available on the market. You should know that Toyota does not warrant their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle. This vehicle should not be modified with non-genuine Toyota products. Modification with non-genuine Toyota products could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from the modification may not be covered under warranty.

for

19

Installation of a mobile two-way radio system

The installation of a mobile two-way radio system in your vehicle could affect electronic systems such as: ●Multiport fuel injection system /sequential multiport fuel injection system ●Cruise control system ●Anti-lock brake system ●SRS airbag system ●Seat belt pretensioner system Be sure to check with your Toyota dealer for precautionary measures or spe- cial instructions regarding installation of a mobile two-way radio system.

20

Vehicle data recordings

Your Toyota is equipped with several sophisticated computers that will record certain data, such as: • Engine speed • Accelerator status • Brake status • Vehicle speed • Shift position The recorded data varies according to the vehicle grade level and options with which it is equipped. Furthermore, these computers do not record con- versations, sounds or pictures. ● Data usage Toyota may use the data recorded in these computers to diagnose malfunc- tions, conduct research and development, and improve quality. Toyota will not disclose the recorded data to a third party except: • With the consent of the vehicle owner or with the consent of the lessee if

•

the vehicle is leased In response to an official request by the police, a court of law or a govern- ment agency

• For use by Toyota in a law suit • For research purposes where the data is not tied to a specific vehicle or

vehicle owner

● Usage of data collected through Safety Connect (U.S.mainland only) If your Toyota has Safety Connect and if you have subscribed to those ser- vices, please refer to the Safety Connect Telematics Subscription Service Agreement for information on data collected and its usage.

21

Event data recorder

This vehicle is equipped with an event data recorder (EDR). The main pur- pose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less. The EDR in this vehicle is designed to record such data as: • How various systems in your vehicle were operating; • Whether or not the driver and passenger safety belts were buckled/fas-

tened;

pedal; and,

• How far (if at all) the driver was depressing the accelerator and/or brake

• How fast the vehicle was traveling. These data can help provide a better understanding of the circumstances in which crashes and injuries occur. NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situ- ation occurs; no data are recorded by the EDR under normal driving condi- tions and no personal data (e.g., name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation. To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.

22

● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehicle)

•

is obtained In response to an official request by the police, a court of law or a govern- ment agency

• For use by Toyota in a law suit However, if necessary, Toyota may: • Use the data for research on vehicle safety performance • Disclose the data to a third party for research purposes without disclosing

information about the specific vehicle or vehicle owner

Scrapping of your Toyota

The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and seat belt pretensioners left as they are, this may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.

Perchlorate Material

Special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate. Your vehicle has components that may contain perchlorate. These compo- nents may include airbag, seat belt pretensioners, and wireless remote con- trol batteries.

23

CAUTION

■General precautions while driving

Driving under the influence: Never drive your vehicle when under the influ- ence of alcohol or drugs that have impaired your ability to operate your vehi- cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury. Defensive driving: Always drive defensively. Anticipate mistakes that other drivers or pedestrians might make and be ready to avoid accidents. Driver distraction: Always give your full attention to driving. Anything that dis- tracts the driver, such as adjusting controls, talking on a cellular phone or reading can result in a collision with resulting death or serious injury to you, your occupants or others.

■General precaution regarding children’s safety

Never leave children unattended in the vehicle, and never allow children to have or use the key. Children may be able to start the vehicle or shift the vehicle into neutral. There is also a danger that children may injure themselves by playing with the windows, the moon roof, or other features of the vehicle. In addition, heat build-up or extremely cold temperatures inside the vehicle can be fatal to children.

24

Symbols used throughout this manual

Cautions & Notices

CAUTION

This is a warning against something which, if ignored, may cause death or serious injury to people. You are informed about what you must or must not do in order to reduce the risk of death or serious injury to yourself and others.

NOTICE

This is a warning against something which, if ignored, may cause damage to the vehicle or its equipment. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toyota and its equipment.

Symbols used in illustrations

Safety symbol The symbol of a circle with a slash through it means “Do not”, “Do not do this”, or “Do not let this happen”.

Arrows indicating operations

Indicates the action (pushing, turning, etc.) used to operate switches and other devices. Indicates the outcome of an operation (e.g. a lid opens).

25

26

Abbreviation list Abbreviation/Acronym list

ABBREVIATIONS

MEANING

A/C ABS ACC

AI-SHIFT

ALR BSM CRS ECO ECU EDR ELR EPS GAWR GVWR

Air Conditioning Anti-lock Brake System Accessory Artificial Intelligence Shift control Automatic Locking Retractor Blind Spot Monitor Child Restraint System Economy/Ecology Electronic Control Unit Event data recorder Emergency Locking Retractor Electric Power Steering Gross Axle Weight Ratings Gross Vehicle Weight Rating

516

Abbreviation list

ABBREVIATIONS

MEANING

I/M

LATCH LED M + S MMT MTBE OBD SRS TIN TPMS TRAC VIN VSC

Emission inspection and maintenance Lower Anchors and Tethers for Children Light Emitting Diode Mud and Snow Methylcyclopentadienyl Manganese Tricarbonyl Methyl Tertiary Butyl Ether On Board Diagnostics Supplemental Restraint System Tire Identification Number Tire Pressure Warning System Traction Control Vehicle Identification Number Vehicle Stability Control

517

1-1. Key information Keys

The following keys are provided with the vehicle. Vehicles without a smart key system (type A)

Master keys Valet key Key number plate

Vehicles without a smart key system (type B)

Master keys Operating the wireless remote control function (→P. 46) Valet key Key number plate

Vehicles without a smart key system (type C)

Master keys Operating the wireless remote control function (→P. 46) Valet key Key number plate

28

1

Vehicles with a smart key system

1-1. Key information

Electronic keys • Operating the smart key

system (→P. 32)

• Operating

the wireless

remote control function (→P. 46)

Mechanical keys Key number plate

Using the mechanical key (vehicles with a smart key system)

To take out the mechanical key, push the release button and take the key out.

The mechanical key can only be inserted in one direction, as the key only has grooves on one side. If the key cannot be inserted in a lock cylinder, turn it over and re-attempt to insert it. After using the mechanical key, store it in the electronic key. Carry the mechanical key together with the electronic key. If the electronic key battery is depleted or the entry function does not operate properly, you will need the mechanical key. (→P. 451)

29

1-1. Key information

■When required to leave the vehicle’s key with a parking attendant

Lock the glove box as circumstances demand. (→P. 290) Vehicles without a smart key system: Carry the master key for your own use and provide the attendant with the valet key. Vehicles with a smart key system: Remove the mechanical key for your own use and provide the attendant with the electronic key only.

■Key number plate

Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key (without a smart key system) or mechanical key (with a smart key system) is lost, a new key can be made by your Toyota dealer using the key number plate. (→P. 450)

■When riding in an aircraft (vehicles with a wireless remote control)

When bringing a key with wireless remote control function onto an aircraft, make sure you do not press any buttons on the key while inside the aircraft cabin. If you are carrying the key in your bag etc., ensure that the buttons are not likely to be pressed accidentally. Pressing a button may cause the key to emit radio waves that could interfere with the operation of the aircraft.

30

1

1-1. Key information

NOTICE

■To prevent key damage

Observe the following: ●Do not drop the keys, subject them to strong shocks or bend them. ●Do not expose the keys to high temperatures for long periods of time. ●Do not get the keys wet or wash them in an ultrasonic washer etc. ●Do not attach metallic or magnetic materials to the keys or place the keys

close to such materials.

●Do not disassemble the keys. ●Do not attach a sticker or anything else to the surface of the key. ●Do not place the keys near objects that produce magnetic fields, such as TVs, audio systems and glass top ranges, or medical electrical equipment, such as low-frequency therapy equipment.

■Carrying the electronic key on your person (vehicles with a smart key

system) Carry the electronic key 3.9 in. (10 cm) or more away from electric appli- ances that are turned on. Radio waves emitted from electric appliances within 3.9 in. (10 cm) of the electronic key may interfere with the key, causing the key to not function properly.

■In case of a smart key system malfunction or other key-related prob-

lems (vehicles with a smart key system) Take your vehicle with all the electronic keys provided with your vehicle to your Toyota dealer.

■When a vehicle key is lost (vehicles with a smart key system)

If the key remains lost, the risk of vehicle theft increases significantly. Visit your Toyota dealer immediately with all remaining electronic keys that was provided with your vehicle.

31

1-2. Opening, closing and locking the doors and trunk Smart key system∗

The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.)

Electronic key

Electronic key

Electronic key

Unlocks and locks the doors (→P. 33) Unlocks the trunk (→P. 33) Starts the engine (→P. 148)

32

∗: If equipped

1-2. Opening, closing and locking the doors and trunk

Unlocking and locking the doors (front door handles only)

Grip the driver’s door handle to unlock the door. Grip the passen- ger’s door handle to unlock all the doors.*

Make sure to touch the sensor on the back of the handle. The doors cannot be unlocked for 3 seconds after the doors are locked. *: The door unlock settings can be

changed. (→P. 38)

the

lock sensor

Touch (the indentation on the side of the door handle) to lock the doors.

Unlocking the trunk

Press the button to unlock the trunk.

33

1-2. Opening, closing and locking the doors and trunk

Antenna location and effective range

■ Antenna location

Antennas outside the cabin Antenna outside the trunk Antenna inside the trunk Antennas inside the cabin

34

1

1-2. Opening, closing and locking the doors and trunk

■ Effective range (areas within which the electronic key is

detected)

(Only

When locking or unlocking the doors The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of either of the front outside door handles. the doors detecting the key can be operated.) When unlocking the trunk The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of the trunk release button. When starting the engine “ENGINE or changing START STOP” switch modes The system can be operated when the electronic key is inside the vehicle.

■Operation signals

Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice) Trunk: A buzzer sounds to indicate that the trunk has been unlocked.

35

1-2. Opening, closing and locking the doors and trunk

■When the door cannot be locked by the lock sensor

Use your palm to touch the lock sensor.

■Alarms and warning indicators

A combination of exterior and interior alarms as well as warning lights are used to prevent theft of the vehicle and unforeseeable accidents resulting from erroneous operation. Take appropriate measures for the warning light that comes on. (→P. 427) The following table describes circumstances and correction procedures when only alarms are sounded.

Alarm

Situation

Exterior alarm sounds once for 5 seconds

An attempt was made to lock the doors using the smart key system while the electronic key was still inside the vehicle. The trunk was closed while the electronic key was still inside the trunk and all the doors were locked. An attempt was made to lock the vehicle while a door was open.

Correction procedure Retrieve the elec- tronic key from the passenger compart- ment and lock the doors again. Retrieve the elec- tronic key from the trunk and close the trunk lid. Close all of the doors and lock the doors again.

36

1

1-2. Opening, closing and locking the doors and trunk

Alarm

Situation

Correction procedure

Interior alarm pings once and exterior alarm sounds once for 5 seconds

Interior alarm sounds continu- ously

An attempt was made to lock either front door by opening a door and putting the inside lock button into the lock position, then closing the door with the electronic key still inside the vehicle. The “ENGINE START STOP” switch was turned to ACCESSORY mode while the driver's door was open (The driver's door was opened when the “ENGINE START STOP” switch was in ACCES- SORY mode.) The driver’s door was opened while any shift position other than P was selected without turning off the “ENGINE START STOP” switch.

Retrieve the elec- tronic key from the vehicle and lock the doors again.

Turn the “ENGINE START STOP” switch off and close the driver’s door.

Shift the shift lever to P.

■Security feature

If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again. (How- ever, depending on the location of the electronic key, the key may be detected as being in the vehicle. In this case, vehicle may be unlocked.)

37

1-2. Opening, closing and locking the doors and trunk

■Switching the door unlock function

It is possible to set which doors the entry function unlocks using the wireless remote control. STEP 1

Turn the “ENGINE START STOP” switch off.

STEP 2

When the indicator light on the key surface is not on, press and hold for about 5 seconds while pressing and holding

, or

The setting changes each time an operation is performed, as shown below. (When changing the setting continuously, release the buttons, wait for at least 5 seconds, and repeat step 2.)

Unlocking doors

Beep

Holding the driver's door handle unlocks only the driver's door. Holding the front passenger’s door handle unlocks all the doors. Holding either front door handle unlocks all the doors.

Exterior: Beeps 3 times Interior: Beeps once

Exterior: Beeps twice Interior: Beeps once

Vehicles with an alarm system: To prevent unintended triggering of the alarm, unlock the doors using the wireless remote control and open and close a door once after the settings have been changed. (If a door is not opened within 60 seconds after is pressed, the doors will be locked again and the alarm will automatically be set.) In case that the alarm is triggered, immediately stop the alarm. (→P. 95)

38

1

1-2. Opening, closing and locking the doors and trunk

■Battery-saving function

The battery-saving function will be activated in order to prevent the elec- tronic key battery and the vehicle battery from being discharged while the vehicle is not in operation for a long time. ●In the following situations, the smart key system may take some time to

unlock the doors. • The electronic key has been left in an area of approximately 6 ft. (2 m)

of the outside of the vehicle for 10 minutes or longer.

• The smart key system has not been used for 5 days or longer.

●If the smart key system has not been used for 14 days or longer, the doors cannot be unlocked at any doors except the driver’s door. In this case, take hold of the driver’s door handle, or use the wireless remote control or the mechanical key, to unlock the doors.

■Electronic key battery-saving function

When battery-saving mode is set, battery depletion is minimized by stopping the electronic key from receiving radio waves.

twice while pressing and . Confirm that the electronic

Press holding key indicator flashes 4 times. While the battery-saving mode is set, the smart key system cannot be used. To cancel the function, press any of the elec- tronic key buttons.

39

1-2. Opening, closing and locking the doors and trunk

■Conditions affecting operation

The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system, wireless remote control and engine immobilizer system from operating properly. (Ways of coping: →P. 451) ●When the electronic key battery is depleted ●Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electri- cal noise

●When the electronic key is in contact with, or is covered by the following

metallic objects • Cards to which aluminum foil is attached • Cigarette boxes that have aluminum foil inside • Metallic wallets or bags • Coins • Hand warmers made of metal • Media such as CDs and DVDs

●When other wireless key (that emit radio waves) is being used nearby ●When carrying the electronic key together with the following devices that

emit radio waves • A portable radio, cellular phone, cordless phone or other wireless com-

munication device

waves

• Another vehicle’s electronic key or a wireless key that emits radio

• Personal computers or personal digital assistants (PDAs) • Digital audio players • Portable game systems

●If window tint with a metallic content or metallic objects are attached to

the rear window

●When the electronic key is placed near a battery charger or electronic

devices

40

1

1-2. Opening, closing and locking the doors and trunk

■Notes for the entry function

●Even when the electronic key is within the effective range (detection

areas), the system may not operate properly in the following cases: • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.

• The electronic key is near the ground or in a high place, or too close to

the rear bumper center when the trunk is unlocked.

• The electronic key is on the instrument panel, rear package tray or floor, in the door pockets or glove box, or near a vent when the engine is started or “ENGINE START STOP” switch modes are changed.

●Do not leave the electronic key on top of the instrument panel or near the door pockets or a vent when exiting the vehicle. Depending on the radio wave reception conditions, it may be detected by the antenna outside the cabin and the door will become lockable from the outside, possibly trap- ping the electronic key inside the vehicle.

●As long as the electronic key is within the effective range, the doors may

be locked or unlocked by anyone.

●Even if the electronic key is not inside the vehicle, it may be possible to

start the engine if the electronic key is near the window.

●The doors may unlock if a large amount of water splashes on the door handle, such as in the rain or in a car wash when the electronic key is within the effective range. (The door will automatically be locked after approximately 60 seconds if the doors are not opened and closed.)

●Gripping the door handle when wearing a glove may not unlock the door. ●If the wireless remote control is used to lock the doors when the elec- tronic key is near the vehicle, there is a possibility that the door may not be unlocked by the entry function. (Use the wireless remote control to unlock the doors.)

●A sudden approach to the effective range or door handle may prevent the doors from being unlocked. In this case, return the door handle to the original position and check that the doors unlock before pulling the door handle again.

41

1-2. Opening, closing and locking the doors and trunk

■Notes for locking the doors

●Touching the door lock sensor while wearing gloves may delay or prevent

lock operation. Remove the gloves and touch the lock sensor again.

●When the lock operation is performed using the lock sensor, recognition signals will be shown up to two consecutive times. After this, no recogni- tion signals will be given.

●If the door handle becomes wet while the electronic key is within the effective range, the door may lock and unlock repeatedly. In that case, follow the following correction procedures to wash the vehicle: • Place the electronic key in a location 6 ft. (2 m) or more away from the

vehicle. (Take care to ensure that the key is not stolen.)

• Set the electronic key to battery-saving mode to disable the smart key

system. (→P. 39)

●If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a buzzer will sound outside the vehicle. To turn off the alarm, lock all the doors.

●The lock sensor may not work properly if it comes into contact with ice,

snow, mud, etc. Clean the lock sensor and attempt to operate it again.

■Notes for the unlocking function

●A sudden approach to the effective range or door handle may prevent the doors from being unlocked. In this case, return the door handle to the original position and check that the doors unlock before pulling the door handle again.

●Gripping the door handle when wearing a glove may not unlock the door. Remove the gloves and touch the sensor on the back of the handle again.

●If the door handle becomes wet while the electronic key is within the effective range, the door may lock and unlock repeatedly. In that case, follow the following correction procedures to wash the vehicle: • Place the electronic key in a location 6 ft. (2 m) or more away from the

vehicle. (Take care to ensure that the key is not stolen.)

• Set the electronic key to battery-saving mode to disable the smart key

system. (→P. 39)

●If there is another electronic key in the detection area, it may take slightly

longer to unlock the doors after the door handle is gripped.

42

1

1-2. Opening, closing and locking the doors and trunk

■When the vehicle is not driven for extended periods

●To prevent theft of the vehicle, do not leave the electronic key within 6 ft.

(2 m) of the vehicle.

●The smart key system can be deactivated in advance. (→P. 493)

■Alarm (if equipped)

Using the smart key system to lock the doors will set the alarm system. (→P. 95)

■To operate the system properly

Make sure to carry the electronic key when operating the system. Do not get the electronic key too close to the vehicle when operating the system from the outside of the vehicle. Depending on the position and holding condition of the electronic key, the key may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door lock prevention function may not operate.)

■If the smart key system does not operate properly

●Locking and unlocking the doors: Use the mechanical key. (→P. 451) ●Starting the engine: →P. 451

43

1-2. Opening, closing and locking the doors and trunk

■Electronic key battery depletion

●The standard battery life is 1 to 2 years. ●If the battery becomes low, an alarm will sound in the cabin when the

engine stops. (→P. 427)

●As the electronic key always receives radio waves, the battery will become depleted even if the electronic key is not used. The following symptoms indicate that the electronic key battery may be depleted. Replace the battery when necessary. (→P. 386) • The smart key system or the wireless remote control does not operate. • The detection area becomes smaller. • The LED indicator on the key surface does not turn on.

●To avoid serious deterioration, do not leave the electronic key within 3 ft. (1 m) of the following electrical appliances that produce a magnetic field: • TVs • Personal computers • Cellular phones, cordless phones and battery chargers • Recharging cellular phones or cordless phones • Glass top ranges • Table lamps

■When the electronic key battery is fully depleted

→P. 386

■If the smart key system has been deactivated in a customized setting ●Locking and unlocking the doors: Use the wireless remote control or

mechanical key. (→P. 46, 451)

●Starting the engine and changing “ENGINE START STOP” switch

modes: →P. 452

●Stopping the engine: →P. 149

■Customization that can be configured at Toyota dealer

Settings (e. g. smart key system) can be changed. (Customizable features: →P. 493)

44

1

1-2. Opening, closing and locking the doors and trunk

■Certification for the smart key system

U.S.A. FCC ID: NI4TMLF10-4
FCC ID: NI4TMLF10-5
FCC ID: HYQ23AAB FCC ID: HYQ14FBA NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

CAUTION

■Caution regarding interference with electronic devices

●People with implanted pacemakers or cardiac defibrillators should keep

away from the smart key system antennas. (→P. 34) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves. Then, consult your doctor to see if you should disable the entry function.

●Users of any electrical medical device other than implanted pacemakers and implanted cardiac defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.

Ask your Toyota dealer for details for disabling the entry function.

45

1-2. Opening, closing and locking the doors and trunk Wireless remote control∗

The wireless remote control can be used to lock and unlock the vehi- cle. Vehicles without a smart key system (type A)

Locks all the doors Sounds the alarm (press and hold) Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Opens the driver’s window and moon roof (press and hold)* Unlocks the trunk (press and hold)

*: This setting must be custom-

ized at your Toyota dealer.

46

∗: If equipped

1

1-2. Opening, closing and locking the doors and trunk

Vehicles without a smart key system (type B)

Vehicles with a smart key system

Locks all the doors Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Opens the driver’s window and moon roof (press and hold)* Sounds the alarm (press and hold) Unlocks the trunk (press and hold)

*: This setting must be custom-

ized at your Toyota dealer.

Locks all the doors Unlocks all the doors Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors. Opens the driver’s window and moon roof (press and hold)* Unlocks the trunk (press and hold) Sounds the alarm (press and hold)

*: This setting must be custom-

ized at your Toyota dealer.

47

1-2. Opening, closing and locking the doors and trunk

■Operation signals

Doors: A buzzer sounds and the emergency flashers flash to indicate that

the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)

Trunk: A buzzer sounds to indicate that the trunk has been unlocked. Driver’s window and moon roof: A buzzer sounds to indicate that the driver’s

window and moon roof are opening.

■Door lock buzzer

If an attempt to lock the doors is made when a door is not fully closed, a buzzer sounds continuously. Fully close the door to stop the buzzer, and lock the vehicle once more.

■Panic mode

Vehicles without a smart key system

When is pressed for longer than about one second, an alarm will sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the wireless remote control.

48

1

1-2. Opening, closing and locking the doors and trunk

Vehicles with a smart key system

When is pressed for longer than about one second, an alarm will sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle. To stop the alarm, press any button on the electronic key.

■Security feature

If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.

■Alarm (if equipped)

Using the wireless remote control to lock the doors will set the alarm system. (→P. 95)

49

1-2. Opening, closing and locking the doors and trunk

■Conditions affecting operation

Vehicles without a smart key system The wireless remote control function may not operate normally in the follow- ing situations: ●When the wireless key battery is depleted ●Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electri- cal noise

●When carrying a portable radio, cellular phone or other wireless commu-

nication devices

●When the wireless key is in contact with, or is covered by a metallic

object

●When other wireless key (that emit radio waves) is being used nearby ●If window tint with a metallic content or metallic objects are attached to

the rear window

Vehicles with a smart key system →P. 40

■If the wireless remote control does not operate properly (vehicles with

a smart key system) Locking and unlocking the doors: Use the mechanical key. (→P. 451)

■Key battery depletion

Vehicles without a smart key system If the wireless remote control function does not operate, the battery may be depleted. Replace the battery when necessary. (→P. 384) Vehicles with a smart key system →P. 44

■When the key battery is fully depleted

→P. 384

■Confirmation of the registered key number (vehicles with a smart key

system) The number of keys already registered to the vehicle can be confirmed. Ask your Toyota dealer for details.

50

1

1-2. Opening, closing and locking the doors and trunk

■Customization that can be configured at Toyota dealer

Settings (e.g. wireless remote control system) can be changed. (Customizable features: →P. 493)

■Certification for wireless remote control

U.S.A. (vehicles without a smart key system) FCC ID: HYQ23AAC FCC ID: HYQ12BDM NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. U.S.A. (vehicles with a smart key system) FCC ID: NI4TMLF10-4
FCC ID: NI4TMLF10-5
FCC ID: HYQ23AAB FCC ID: HYQ14FBA NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Canada NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.

51

1-2. Opening, closing and locking the doors and trunk Doors

The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch. ■ Entry function (vehicles with a smart key system)

→P. 32

■ Wireless remote control (if equipped)

→P. 46

■ Key Turning the key operates the doors as follows: Vehicles without a smart key system

Locks all the doors Unlocks all the doors Driver’s side only: Turning the key unlocks the driver's door. Turning the key again unlocks the other doors.

Vehicles with a smart key system The doors can also be locked and unlocked with the mechanical key. (→P. 451) ■ Door lock switch

Locks all the doors Unlocks all the doors

52

1

1-2. Opening, closing and locking the doors and trunk

■ Inside lock button

Unlocks the door Locks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.

Locking the doors from the outside without a key

STEP 1

STEP 2

Move the inside lock button to the lock position. Close the door.

Vehicles without a smart key system

The door cannot be locked if either of the front doors is open and the key is in the engine switch.

Vehicles with a smart key system

The door cannot be locked if the “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode, or the electronic key is left inside the vehicle. The key may not be detected correctly and the door may be locked.

53

1-2. Opening, closing and locking the doors and trunk

Rear door child-protector lock

The door cannot be opened from inside the vehicle when the lock is set.

Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.

54

1-2. Opening, closing and locking the doors and trunk

Automatic door locking and unlocking systems

The following functions can be set or cancelled:

Function

Shift position linked door locking function Shift position linked door unlocking function

Speed linked door lock- ing function

Operation

Shifting the shift lever out of P locks all the doors. Shifting the shift lever to P unlocks all the doors. All the doors are locked when the vehicle speed is approximately 12 mph (20 km/h) or higher.

All the doors are unlocked when the driver's door is opened within 10 seconds after turn- ing the engine switch to “ACC” or “LOCK”.

Driver's door linked door unlocking function (vehicles without a smart key system) Driver's door linked door unlocking function (vehicles with a smart key system) ■ Setting and canceling the functions (vehicles without naviga-

All the doors are unlocked when the driver's door is opened within 10 seconds after turn- ing the “ENGINE START STOP” switch off.

tion system and Display Audio system) To switch between setting and canceling, follow the procedure below.

STEP 1

Vehicles without a smart key system Close all the doors and turn the engine switch to the “ON” position. (Perform step 2 within 10 seconds.) Vehicles with a smart key system Close all the doors and turn the “ENGINE START STOP” switch to IGNITION ON mode. (Perform step 2 within 10 sec- onds.)

55

1-2. Opening, closing and locking the doors and trunk

STEP 2

Shift the shift lever to P or N, and press and hold the driver's door lock for approximately 5 seconds and then release.

switch

or

to

corresponding

The shift lever and switch posi- tions the desired function to be set are shown in the following table. Use the same procedure to can- cel the function.

Function

Shift lever position

Driver’s door lock switch position

Shift position linked door lock- ing function Shift position linked door unlocking function Speed linked door locking func- tion Driver's door linked door unlock- ing function

When the setting or canceling operation is complete, all doors are locked and then unlocked.

56

1-2. Opening, closing and locking the doors and trunk

■If a wrong key is used (vehicles with a smart key system)

The key cylinder rotates freely to isolate inside mechanism.

■If the smart key system has been deactivated in a customized setting

(vehicles with a smart key system) Use the wireless remote control or mechanical key. (→P. 46, 451)

■Customization that can be configured at Toyota dealer

Settings (e.g. unlocking function using a key) can be changed. (Customizable features →P. 493)

CAUTION

■To prevent an accident

Observe the following precautions while driving the vehicle. Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●Always use a seat belt. ●Always lock all the doors. ●Ensure that all doors are properly closed. ●Do not pull the inside handle of the doors while driving.

The doors may be opened and the passengers are thrown out of the vehi- cle and it may result in serious injury or death. Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in locked position.

●Set the rear door child-protector locks when children are seated in the rear

seats.

57

1-2. Opening, closing and locking the doors and trunk Trunk

The trunk can be opened using the key, trunk opener, entry function or wireless remote control. ■ Opening the trunk from inside the vehicle

Pull up the lever to release the trunk lid.

■ Opening the trunk from outside the vehicle Key (vehicles without a wireless remote control)

Turn the master key clockwise to release the trunk lid.

Entry function (vehicles with a smart key system) →P. 32
Wireless remote control (if equipped) →P. 46

58

1

1-2. Opening, closing and locking the doors and trunk

■Trunk light

The trunk light turns on when the trunk is opened.

■Function to prevent the trunk being locked with the electronic key

inside (vehicles with a smart key system) ●When all doors are being locked, closing the trunk lid with the electronic

key left inside the trunk will sound an alarm. In this case, the trunk lid can be opened using the entry function.

●Even when the spare electronic key is put in the trunk with all the doors locked, the key confinement prevention function can be activated so the trunk can be opened. In order to prevent theft, take all electronic keys with you when leaving the vehicle.

●Even when the electronic key is put in the trunk with all the doors are locked, the key may not be detected depending on the places and the surrounding radio wave conditions. In this case, the key confinement pre- vention function cannot be activated, causing the doors to lock when the trunk is closed. Make sure to check where the key is before closing the trunk.

●The key confinement prevention function cannot be activated if any one of the doors is unlocked. In this case, open the trunk using the trunk opener.

■Internal trunk release lever

The trunk lid can be opened by pulling up the glow-in-the-dark lever located on the inside of the trunk lid. The lever will continue to glow for some time after the trunk lid is closed.

59

1-2. Opening, closing and locking the doors and trunk

CAUTION

■Caution while driving

●Keep the trunk lid closed while driving.

If the trunk lid is left open, it may hit near-by objects while driving or lug- gage in the trunk may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard. Make sure to close the trunk lid before driving.

●Before driving the vehicle, make sure that the trunk lid is fully closed. If the trunk lid is not fully closed, it may open unexpectedly while driving, caus- ing an accident.

●Never let anyone sit in the trunk. In the event of sudden braking or a colli-

sion, they are susceptible to death or serious injury.

■When children are in the vehicle Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not allow children to enter the trunk.

If a child is accidentally locked in the trunk, they could overheat or suffo- cate.

●Do not allow a child to open or close the trunk lid.

Doing so may cause the trunk lid to operate unexpectedly, or cause the child’s hands, head, or neck to be caught by the closing trunk lid.

60

1

1-2. Opening, closing and locking the doors and trunk

CAUTION

■Using the trunk

Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in seri- ous injury. ●Remove any heavy loads, such as snow and ice, from the trunk lid before opening it. Failure to do so may cause the trunk lid to fall closed again after it is opened.

●When opening or closing the trunk lid, thoroughly check to make sure the

surrounding area is safe.

●If anyone is in the vicinity, make sure they are safe and let them know that

the trunk is about to open or close.

●Use caution when opening or closing the trunk lid in windy weather as it

may move abruptly in strong wind.

●The trunk lid may fall if it is not opened fully. It is more difficult to open or close the trunk lid on an incline than on a level surface, so beware of the trunk lid unexpectedly opening or closing by itself. Make sure that the trunk lid is fully open and secure before using the trunk.

●When closing the trunk lid, take extra care to prevent your fingers etc. from being caught.

●When closing the trunk lid, make sure

to press it lightly on its outer surface.

●Do not attach any accessories other than genuine Toyota parts to the trunk lid. Such additional weight on the trunk lid may cause the lid to fall closed again after it is opened.

61

1-2. Opening, closing and locking the doors and trunk

62

1-2. Opening, closing and locking the doors and trunk

63

1-3. Adjustable components (seats, mirrors, steering wheel) Front seats

Manual seat

Seat position adjustment lever Seatback angle adjustment lever Vertical height adjustment lever (driver’s side only)

62

1-3. Adjustable components (seats, mirrors, steering wheel)

Power seat

Seat position adjustment switch Seatback angle adjustment switch Seat cushion (front) angle adjustment switch (driver’s side only) Vertical height adjustment switch (driver’s side only) Lumbar support adjustment switch (driver’s side only)

63

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■Seat adjustment

●To reduce the risk of sliding under the lap belt during a collision, do not

recline the seat more than necessary. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen, or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident. Adjustments should not be made while driving as the seat may unexpect- edly move and cause the driver to lose control of the vehicle.

●Manual seat only: After adjusting the seat, make sure that the seat is

locked in position.

64

1-3. Adjustable components (seats, mirrors, steering wheel) Rear seats

The seatbacks of the rear seats can be folded down.

Folding down the rear seatbacks

Pull the seatback lever in the trunk for the seatback you wish to fold down.

CAUTION

■When folding the rear seatbacks down

Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not fold the seatbacks down while driving. ●Stop the vehicle on level ground, set the parking brake and shift the shift

lever to P.

●Do not allow anyone to sit on a folded seatback or in the trunk while driv-

ing.

●Do not allow children to enter the trunk.

65

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■When returning the seat to its original position

●Ensure that the seat belt does not get caught between or behind the seats. ●If the seat belt has been released from its guide, pass the seat belt through

its guide. (→P. 72)

■Seat adjustment

Be careful not to get hands or feet pinched between the rear console box and the rear seat when folding down the rear seatback. ■After returning the seatback to the upright position

Observe the following precautions. Failure to do so may result in death or serious injury. ●Make sure the seatback is securely locked by pressing it forward and rear-

ward on the top.

●Check that the seat belts are not twisted or caught in the seatback. ●Make sure that the seat belt is passing through its guide.

NOTICE

■When left seatback is folded down

Make sure the luggage loaded in the enlarged trunk will not damage the webbing of the rear center seat belt.

66

1

1-3. Adjustable components (seats, mirrors, steering wheel) Head restraints

Head restraints are provided for all seats.

(front

adjustment

Vertical seats) Up Pull the head restraints up. Down Push the head restraint down while pushing the lock release button.

Lock release button

■Removing the head restraints (front seats)

Pull the head restraint up while pressing the lock release button.

■Installing the head restraints (front seats)

Align the head restraint with the installa- tion holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.

67

1-3. Adjustable components (seats, mirrors, steering wheel)

■Adjusting the height of the head restraints (front seats)

Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.

CAUTION

■Head restraint precautions (front seats)

Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ●Use the head restraints designed for each respective seat. ●Adjust the head restraints to the correct position at all times. ●After adjusting the head restraints, push down on them and make sure

they are locked in position.

●Do not drive with the head restraints removed.

68

1-3. Adjustable components (seats, mirrors, steering wheel) Seat belts

Make sure that all occupants are wearing their seat belts before driv- ing the vehicle. ■ Correct use of the seat belts

● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoul- der.

● Position the lap belt as low

as possible over the hips.

● Adjust the position of the seatback. Sit up straight and well back in the seat. ● Do not twist the seat belt.

■ Fastening and releasing the seat belt

To fasten the seat belt, push the plate into the buckle until a click sound is heard. To release the seat belt, press the release button.

Release button

69

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Adjusting the seat belt shoulder anchor height (front seats) Push the seat belt shoulder anchor down while pressing the release button. Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed until you hear a click.

Seat belt pretensioners (front seats)

The pretensioner helps the seat belt to quickly restrain the occu- pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal or side collision.

The pretensioner may not acti- vate in the event of a minor frontal impact, a minor side impact, a rear impact or a vehicle rollover.

70

1-3. Adjustable components (seats, mirrors, steering wheel)

■Emergency locking retractor (ELR)

The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.

■Automatic locking retractor (ALR)

When a passenger's shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly. To free the belt again, fully retract the belt and then pull the belt out once more. (→P. 122)

■Pregnant women

Obtain medical advice and wear the seat belt in the proper way. (→P. 69) Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu- pants. Extend the shoulder belt com- pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area. If the seat belt is not worn properly, not only a pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking or a collision.

■People suffering illness

Obtain medical advice and wear the seat belt in the proper way. (→P. 69)

■Child seat belt usage

The seat belts of your vehicle were principally designed for persons of adult size. ●Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle's seat belt. (→P. 118) ●When the child becomes large enough to properly wear the vehicle's seat

belt, follow the instructions on P. 69 regarding seat belt usage.

71

1-3. Adjustable components (seats, mirrors, steering wheel)

■Replacing the belt after the pretensioner has been activated

If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli- sions.

■Seat belt extender

If your seat belts cannot be fastened