Download PDF Manual

securely because long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.


they are not


Use the seat belt after passing it through the guide if the seat belt comes free from the guide.


■Rear seat belt


72


1-3. Adjustable components (seats, mirrors, steering wheel)


CAUTION


Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failure to do so may cause death or severe injury. ■Wearing a seat belt


●Ensure that all passengers wear a seat belt. ●Always wear a seat belt properly. ●Each seat belt should be used by one person only. Do not use a seat belt


for more than one person at once, including children.


●Toyota recommends that children be seated in the rear seat and always


use a seat belt and/or an appropriate child restraint system.


●To achieve a proper seating position, do not recline the seat more than necessary. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.


●Do not wear the shoulder belt under your arm. ●Always wear your seat belt low and snug across your hips.


■When children are in the vehicle


Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.


■Seat belt pretensioners


●Do not place anything, such as a cushion, on the front passenger's seat. Doing so will disperse the passenger's weight, which prevents the sensor from detecting the passenger's weight properly. As a result, the seat belt pretensioner for the front passenger's seat may not activate in the event of a collision.


●If the pretensioner has activated, the SRS warning light will come on. In that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.


73


1-3. Adjustable components (seats, mirrors, steering wheel)


CAUTION


■Adjustable shoulder anchor


Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in the event of a sudden stop, sudden swerve or accident. (→P. 70)


■Seat belt damage and wear


●Do not damage the seat belts by allowing the belt, plate, or buckle to be


jammed in the door.


●Inspect the seat belt system periodically. Check for cuts, fraying, and loose parts. Do not use a damaged seat belt until it is replaced. Damaged seat belts cannot protect an occupant from death or serious injury.


●Ensure that the belt and plate are locked and the belt is not twisted.


If the seat belt does not function correctly, immediately contact your Toyota dealer.


●Replace the seat assembly, including the belts, if your vehicle has been


involved in a serious accident, even if there is no obvious damage.


●Do not attempt to install, remove, modify, disassemble or dispose of the seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly, resulting in death or serious injury.


●Always make sure the shoulder belt passes through the guide when using the seat belt. Failure to properly position the belt may reduce the amount of protection in an accident and could lead to death or serious injury in a collision or sudden stop.


●Always make sure that the seat belt is not twisted, does not get caught in


the guide or the seatback and is arranged in the proper position.


74


1-3. Adjustable components (seats, mirrors, steering wheel)


CAUTION


■Using a seat belt extender


●Do not wear the seat belt extender if you can fasten the seat belt without


the extender.


●Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.


●The personalized extender may not be safe on another vehicle, when used by another person, or at a different seating position other than the one originally intended.


NOTICE


■When using a seat belt extender


When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.


75


1-3. Adjustable components (seats, mirrors, steering wheel) Steering wheel


The steering wheel can be adjusted to a comfortable position.


STEP 1


STEP 2


Hold the steering wheel and push the lever down.


Adjust to the ideal position by moving the steering wheel horizontally and vertically.


After adjustment, pull the lever up the steering wheel.


to secure


CAUTION


■Caution while driving


Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury.


■After adjusting the steering wheel


Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident, and resulting in death or serious injury.


76


1-3. Adjustable components (seats, mirrors, steering wheel) Anti-glare inside rear view mirror


Glare from the headlights of vehicles behind can be reduced by using the following functions: Manual anti-glare inside rear view mirror


Normal position Anti-glare position


Auto anti-glare inside rear view mirror In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.


Turns automatic mode on/off


The indicator comes on when automatic mode is turned on. Vehicles without a smart key system The mirror will revert to the automatic mode each time the engine switch is turned to the “ON” position. Vehicles with a smart key system The mirror will revert to the automatic mode each time the “ENGINE STOP” switch is turned to IGNITION ON mode.


START


77


1-3. Adjustable components (seats, mirrors, steering wheel)


Adjusting the height of rear view mirror


Adjust the height of the rear view mirror by moving it up and down.


■To prevent sensor error (vehicles with auto anti-glare inside rear view


mirror)


To ensure that the sensors operate prop- erly, do not touch or cover them.


CAUTION


■Caution while driving


Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.


78


1-3. Adjustable components (seats, mirrors, steering wheel) Outside rear view mirrors


Mirror angle can be adjusted using the switch.


STEP 1


STEP 2


To select a mirror to adjust, press the switch.


Left Right


To adjust the mirror, press the switch.


Up Right Down Left


Folding the mirrors


Push the mirror back in the direc- tion of the vehicle's rear.


79


1-3. Adjustable components (seats, mirrors, steering wheel)


■Mirror angle can be adjusted when


Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.


■When the mirrors are fogged up (vehicles with mirror defoggers)


Turn on the mirror defoggers to defog the mirrors. (→P. 240)


CAUTION


■When driving the vehicle


Observe the following precautions while driving. Failure to do so may result in loss of control of the vehicle and cause an accident, resulting in death or serious injury. ●Do not adjust the mirrors while driving. ●Do not drive with the mirrors folded. ●Both the driver and passenger side mirrors must be extended and properly


adjusted before driving. ■When a mirror is moving


To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.


■When the mirror defoggers are operating (vehicles with mirror defog-


gers) Do not touch the rear view mirror surfaces, as they can become very hot and burn you.


80


1


1-4. Opening and closing the windows and moon roof Power windows


The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows:


Closing One-touch closing (driver’s window only)* Opening One-touch opening (driver’s window only)*


*: Pressing


the switch


the opposite direction will stop win- dow travel partway.


in


Window lock switch


Press the switch down to lock the passenger window switches. Use this switch to prevent chil- dren from accidentally opening or closing a passenger window.


81


1-4. Opening and closing the windows and moon roof


■The power windows can be operated when


Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode. ■Operating the power windows after turning the engine off


Vehicles without a smart key system The power windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They can- not, however, be operated once either front door is opened. Vehicles with a smart key system The power windows can be operated for approximately 45 seconds even after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. They cannot, however, be operated once either front door is opened.


■Jam protection function (driver’s window only)


If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.


■When the power window does not close normally (driver’s window


only) If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the driver’s door. ●Vehicles without a smart key system: After stopping the vehicle, the win- dow can be closed by holding the power window switch in the one-touch closing position while the engine switch is turned to the “ON” position.


●Vehicles with a smart key system: After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch clos- ing position while the “ENGINE START STOP” switch is turned to IGNI- TION ON mode.


●If the window still cannot be closed even by carrying out the operation explained above, initialize the function by performing the following proce- dure.


82


1


1-4. Opening and closing the windows and moon roof


STEP 1


STEP 2


STEP 3


Hold the power window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the win- dow has closed. Hold the power window switch in the one-touch opening position. Continue holding the switch for a further 2 seconds after the win- dow has opened completely. Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.


If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after perform- ing the above procedure correctly, have the vehicle inspected by your Toyota dealer.


■Customization that can be configured at Toyota dealer


Settings (e.g. key linked operation) can be changed. (Customizable features: →P. 493)


CAUTION


■Closing the windows


Observe the following precautions. Failure to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their body


in a position where it could be caught when a window is being operated.


●Do not allow children to operate the power windows.


Closing a power window on someone can cause serious injury, and in some instances, even death.


■Jam protection function (driver’s window only)


●Never use any part of your body to intentionally activate the jam protection


function.


●The jam protection function may not work if something gets caught just


before the window fully closes.


83


1-4. Opening and closing the windows and moon roof Moon roof∗


Use the overhead switches to open and close the moon roof and tilt it up and down. ■ Opening and closing


Opens the moon roof* The moon roof stops slightly before the fully open position to reduce wind noise. Press the switch again to fully open the moon roof. Closes the moon roof*


*: Lightly press the switch in either direction to stop the moon roof partway.


Tilts the moon roof up* Tilts the moon roof down*


*: Lightly press either of the moon roof switches to stop the moon roof partway.


■ Tilt up and down


84


∗: If equipped


1


1-4. Opening and closing the windows and moon roof


■The moon roof can be operated when Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.


■Operating the moon roof after turning the engine off


Vehicles without a smart key system The moon roof can be operated for approximately 45 seconds after the engine switch is turned to the “ACC” or “LOCK” position. It cannot, however, be operated once either front door is opened. Vehicles with a smart key system The moon roof can be operated for approximately 45 seconds after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. It cannot, however, be operated once either front door is opened.


■Jam protection function


If an object is detected between the moon roof and the frame while the moon roof is closing or tilting down, travel is stopped and the moon roof opens slightly.


■Sunshade


The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.


85


1-4. Opening and closing the windows and moon roof


■When the moon roof does not close normally


Perform the following procedure: ●If the moon roof closes but then re-opens slightly STEP 1


STEP 2


STEP 3


STEP 2


STEP 3


STEP 4


Stop the vehicle. Press and hold the “CLOSE” switch.*1
The moon roof will close, reopen and pause for approximately 10
seconds.*2 Then it will close again, tilt up and pause for approxi- mately 1 second. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.


●If the moon roof tilts down but then tilts back up STEP 1


Stop the vehicle. Press and hold the “UP” switch*1 until the moon roof moves into the tilt up position and stops. Release the “UP” switch once and then press and hold the “UP” switch again.*1
The moon roof will pause for approximately 10 seconds in the tilt up position.*2 Then it will adjust slightly and pause for approximately 1
second. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.


*1: If the switch is released at the incorrect time, the procedure will have to


be performed again from the beginning.


*2: If the switch is released after the above mentioned 10 second pause, automatic operation will be disabled. In that case, press and hold the open/close switch in the close position or press and hold the “UP” switch. The moon roof will tilt up and pause for approximately 1 second. Then it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.


If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.


86


1


1-4. Opening and closing the windows and moon roof


■Moon roof open reminder function


Vehicles without a smart key system An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the engine switch off. Vehicles with a smart key system An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the “ENGINE START STOP” switch off.


■Customization that can be configured at Toyota dealer


Settings (e.g. key linked operation) can be changed. (Customizable features: →P. 493)


CAUTION


■Opening the moon roof


Observe the following precautions. Failure to do so may cause death or serious injury. ●Do not allow any passengers to put their hands or heads outside the vehi-


cle while it is moving.


●Do not sit on top of the moon roof.


■Closing the moon roof


Observe the following precautions. Failure to do so may result in death or serious injury. ●Check to make sure that all passengers do not have any part of their bod- ies in a position where they could be caught when the moon roof is being operated.


●Do not allow children to operate the moon roof.


Closing the moon roof on someone can cause death or serious injury.


■Jam protection function


●Never use any part of your body to intentionally activate the jam protection


function.


●The jam protection function may not work if something gets caught just


before the moon roof fully closes.


87


1-5. Refueling Opening the fuel tank cap


Perform the following steps to open the fuel tank cap: ■ Before refueling the vehicle


Vehicles without a smart key system Turn the engine switch off and ensure that all the doors and win- dows are closed. Vehicles with a smart key system Turn the “ENGINE START STOP” switch off and ensure that all the doors and windows are closed.


■ Opening the fuel tank cap STEP 1


Pull up the opener to open the fuel filler door.


STEP 2


Turn the fuel tank cap slowly to open.


88


1-5. Refueling


STEP 3


Hang the fuel tank cap on the back of the fuel filler door.


Closing the fuel tank cap


After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.


89


1-5. Refueling


CAUTION


■When refueling the vehicle


Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury. ●After exiting the vehicle and before opening the fuel door, touch an unpainted metal surface to discharge any static electricity. It is important to discharge static electricity before refueling because sparks resulting from static electricity can cause fuel vapors to ignite while refueling.


●Always hold the grips on the fuel tank cap and turn it slowly to remove it. A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out the filler neck and cause injury.


●Do not allow anyone that has not discharged static electricity from their


body to come close to an open fuel tank.


●Do not inhale vaporized fuel.


Fuel contains substances that are harmful if inhaled.


●Do not smoke while refueling the vehicle.


Doing so may cause the fuel to ignite and cause a fire.


●Do not return to the vehicle or touch any person or object that is statically


charged. This may cause static electricity to build up, resulting in a possible ignition hazard.


■When refueling


Securely insert the fuel nozzle into the fuel filler neck. If fuel is added with the nozzle slightly lifted away from the fuel filler neck, the automatic shut off function may not operate, resulting in fuel overflowing from the tank.


■When replacing the fuel cap


Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.


90


1-5. Refueling


NOTICE


■Refueling


Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface.


91


1-6. Theft deterrent system Engine immobilizer system


The vehicle's keys have built-in transponder chips that prevent the engine from starting if a key has not been previously registered in the vehicle's on-board computer. Never leave the keys inside the vehicle when you leave the vehicle.


Vehicles without a smart key system The indicator light flashes after the key has been removed from the engine switch to indi- cate that the system is operat- ing. The indicator light stops flash- ing after the registered key has been inserted into the engine switch to indicate that the system has been can- celed. Vehicles with a smart key system The indicator light flashes after the “ENGINE START STOP” switch has been turned off to indicate that the system is operating. The indicator light stops flash- ing after the “ENGINE START STOP” switch has been turned to ACCESSORY or IGNITION ON mode to indicate that the system has been canceled.


92


1


1-6. Theft deterrent system


■System maintenance


The vehicle has a maintenance-free type engine immobilizer system.


■Conditions that may cause the system to malfunction


●If the grip portion of the key is in contact with a metallic object ●If the key is in close proximity to or touching a key to the security system


(key with a built-in transponder chip) of another vehicle


■Certifications for the engine immobilizer system


U.S.A. Vehicles without a smart key system FCC ID: WRKRI-34BTY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. Vehicles with a smart key system FCC ID: NI4TMIMB-3
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. Canada Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device.


CAUTION


■Certifications for the immobilizer system


Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.


93


1-6. Theft deterrent system


NOTICE


■To ensure the system operates correctly


Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.


94


1


1-6. Theft deterrent system Alarm∗


The system sounds the alarm and flashes the lights when forced entry is detected. ■ Triggering of the alarm


The alarm is triggered in the following situations when the alarm is set: ● A locked door or trunk is unlocked or opened in any way other than using the entry function, wireless remote control or mechanical key.


● The hood is opened. ● Some models: The window is tapped or broken.


■ Setting the alarm system


Close the doors, trunk and hood, and lock all the doors. The system will be set auto- matically after 30 seconds.


indicator


The light changes from being on to flashing when the system is set.


∗: If equipped 95


1-6. Theft deterrent system


■ Deactivating or stopping the alarm


Do one of the following to deactivate or stop the alarm. ● Unlock the doors or trunk. ● Vehicles without a smart key system: Turn the engine switch to the “ACC” or “ON” position, or start the engine. (The alarm will be deactivated or stopped after a few seconds.)


● Vehicles with a smart key system: Turn the “ENGINE START STOP” switch to ACCESSORY or IGNITION ON mode, or start the engine. (The alarm will be deactivated or stopped after a few seconds.)


■System maintenance


The vehicle has a maintenance-free type alarm system.


■Items to check before locking the vehicle


To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following: ●Nobody is in the vehicle. ●The windows and moon roof are closed before the alarm is set. ●No valuables or other personal items are left in the vehicle.


96


1-6. Theft deterrent system


■Triggering of the alarm


The alarm may be triggered in the following situations. (Stopping the alarm deactivates the system.)


●A person inside the vehicle opens a


door, the trunk or hood.


●The battery is recharged or replaced


when the vehicle is locked.


■Alarm-operated door lock


●When the alarm is operating, the doors are locked automatically to pre-


vent intruders.


●Do not leave the key inside the vehicle when the alarm is operating, and make sure the key is not inside the vehicle when recharging or replacing the battery.


NOTICE


■To ensure the system operates correctly


Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.


97


1-7. Safety information Correct driving posture


Drive in a good posture as follows:


and to


Sit upright and well back in the seat. (→P. 62) Adjust the position of the seat forward or backward to ensure the pedals can be reached easily the extent depressed required. (→P. 62) Adjust the seatback so that the controls are easily oper- able. Adjust the tilt and telescopic positions of the steering wheel downward so the air- bag is facing your chest. (→P. 76) Lock the head restraint in place with the center of the head restraint closest to the top of your ears. (→P. 67) Wear the seat belt correctly. (→P. 69)


98


1-7. Safety information


CAUTION


■While driving


●Do not adjust the position of the driver’s seat.


Doing so could cause the driver to lose control of the vehicle.


●Do not place a cushion between the driver or passenger and the seatback. A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.


●Do not place anything under the front seats.


Objects placed under the front seats may become jammed in the seat tracks and stop the seat from locking in place. This may lead to an acci- dent, resulting in death or serious injury. The adjustment mechanism may also be damaged.


■Adjusting the seat position


●Take care when adjusting the seat position to ensure that other passen-


gers are not injured by the moving seat.


●Do not put your hands under the seat or near the moving parts to avoid


injury. Fingers or hands may become jammed in the seat mechanism.


99


1-7. Safety information SRS airbags


The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.


SRS front airbags


SRS driver airbag/front passenger airbag Can help protect the head and chest of the driver and front pas- senger from impact with interior components SRS knee airbags Can help provide driver and front passenger protection


SRS side and curtain shield airbags


SRS front side airbags Can help protect the torso of the front seat occupants SRS rear side airbags Can help protect the torso of occupants in the rear outer seats


100


1-7. Safety information


SRS curtain shield airbags Can help protect primarily the head of occupants in the outer seats


SRS airbag system components


Front impact sensors Front passenger occupant classification system (ECU and sensors) Knee airbags Side impact sensors (front door) Side impact sensors (front) Front passenger airbag Front side airbags Curtain shield airbags Rear side airbags


“AIR BAG ON” and “AIR BAG OFF” indicator lights SRS warning light Front passenger’s seat belt buckle switch Airbag sensor assembly Side impact sensors (rear) Driver airbag Driver’s seat belt buckle switch Seat belt pretensioners and force limiters


101


1-7. Safety information


Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on infor- mation obtained from the sensors etc. shown in the system compo- nents diagram above. This information includes crash severity and occupant information. As the airbags deploy, a chemical reaction in the inflators quickly fills the airbags with nontoxic gas to help restrain the motion of the occupants.


102


1


1-7. Safety information


■If the SRS airbags deploy (inflate)


●Bruising and slight abrasions may result from contact with a deploying


(inflating) SRS airbag.


●A loud noise and white powder will be emitted. ●Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the seats, parts of the front and rear pillars, and roof side rails, may be hot for several minutes. The airbag itself may also be hot.


●The windshield may crack. ●For Safety Connect subscribers, if the SRS airbags deploy or in the event of a severe rear-end collision, the system is designed to send an emer- gency call to the response center, notifying them of the vehicle’s location (without needing to push the “SOS” button) and an agent will attempt to speak with the occupants to ascertain the level of emergency and assis- tance required. If the occupants are unable to communicate, the agent automatically treats the call as an emergency and helps to dispatch the necessary emergency services. (→P. 326)


■SRS airbag deployment conditions (SRS front airbags)


●The SRS front airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corresponding to an approxi- mately 12 - 18 mph [20 - 30 km/h] frontal collision with a fixed wall that does not move or deform). However, this threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle and sign pole, which can move or deform on impact, or if the vehicle is involved in an underride collision (e.g. a collision in which the front of the vehicle “underrides”, or goes under, the bed of a truck etc.).


●Depending on the type of collision, it is possible that only the seat belt


pretensioners will activate.


●The SRS front airbags for the front passenger will not activate if there is no passenger sitting in the front passenger seat. However, the SRS front airbags for the front passenger may deploy if luggage is put in the seat, even if the seat is unoccupied. (→P. 113)


103


1-7. Safety information


■SRS airbag deployment conditions (SRS side and curtain shield air-


bags) ●The SRS side and curtain shield airbags will deploy in the event of an impact that exceeds the set threshold level (the level of force corre- sponding to the impact force produced by an approximately 3300 lb. [1500 kg] vehicle colliding with the vehicle cabin from a direction perpen- dicular to the vehicle orientation at an approximate speed of 12 - 18 mph [20 - 30 km/h]).


●The SRS curtain shield airbags may also deploy in the event of a severe


frontal collision.


■Conditions under which the SRS airbags may deploy (inflate), other


than a collision The SRS front airbags and SRS curtain shield airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.


●Hitting a curb, edge of pavement or


hard surface


●Falling into or jumping over a deep hole ●Landing hard or falling


104


1-7. Safety information


■Types of collisions that may not deploy the SRS airbags (SRS front air-


bags) The SRS front airbags do not generally inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low-speed frontal collision. But, whenever a collision of any type causes sufficient forward deceleration of the vehicle, deployment of the SRS front airbags may occur.


●Collision from the side ●Collision from the rear ●Vehicle rollover


105


1-7. Safety information


■Types of collisions that may not deploy the SRS airbags


(SRS side and curtain shield airbags) The SRS side and curtain shield airbags may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment.


●Collision from the side to the vehicle body other than the passenger com- partment


●Collision from the side at an angle


SRS side airbags: Do not generally inflate if the vehicle is involved in a fron- tal or rear collision, if it rolls over, or if it is involved in a low-speed side colli- sion. SRS curtain shield airbags: Do not generally inflate if the vehicle is involved in a rear collision, if it rolls over, or if it is involved in a low-speed side colli- sion.


●Collision from the front* ●Collision from the rear ●Vehicle rollover *: Depending on the conditions and type of accident, the curtain shield airbags may deploy frontal impact.


(inflate) upon


106


1


1-7. Safety information


■When to contact your Toyota dealer


In the following cases, contact your Toyota dealer as soon as possible. ●Any of the SRS airbags have been inflated.


●The front of the vehicle is damaged or deformed, or was involved in an acci- dent that was not severe enough to cause the SRS front airbags and SRS curtain shield airbags to inflate.


●A portion of a door is damaged or deformed, or the vehicle was involved in an accident that was not severe enough to cause the SRS side and cur- tain shield airbags to inflate.


●The pad section of the steering wheel, dashboard near the front passenger air- bag or lower portion of the instrument panel is scratched, cracked, or other- wise damaged.


●The surface of the seats with the side airbag is scratched, cracked, or other- wise damaged.


●The portion of the front pillars, rear pil- lars or roof side rail garnishes (padding) containing the curtain shield airbags inside is scratched, cracked, or other- wise damaged.


107


1-7. Safety information


CAUTION


■SRS airbag precautions


Observe the following precautions regarding the SRS airbags. Failure to do so may cause death or serious injury. ●The driver and all passengers in the vehicle must wear their seat belts


properly. The SRS airbags are supplemental devices to be used with the seat belts. ●The SRS driver airbag deploys with considerable force, and can cause


death or serious injury especially if the driver is very close to the airbag. The National Highway Traffic Safety Administration (NHTSA) advises: Since the risk zone for the driver’s airbag is the first 2 - 3 in. (50 - 75 mm) of inflation, placing yourself 10 in. (250 mm) from your driver airbag pro- vides you with a clear margin of safety. This distance is measured from the center of the steering wheel to your breastbone. If you sit less than 10 in. (250 mm) away now, you can change your driving position in several ways: • Move your seat to the rear as far as you can while still reaching the


pedals comfortably.


• Slightly recline the back of the seat.


Although vehicle designs vary, many drivers can achieve the 10 in. (250 mm) distance, even with the driver seat all the way forward, sim- ply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non-slippery cushion, or raise the seat if your vehicle has that feature. • If your steering wheel is adjustable, tilt it downward. This points the air-


bag toward your chest instead of your head and neck.


The seat should be adjusted as recommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.


108


1


CAUTION


■SRS airbag precautions


1-7. Safety information


●If the seat belt extender has been con- nected to the front seat belt buckles but the seat belt extender has not also been fastened to the latch plate of the seat belt, the SRS front airbags will judge that the driver and front passen- ger are wearing the seat belt even though the seat belt has not been con- nected. In this case, the SRS front air- bags may not activate correctly in a collision, resulting in death or serious injury in the event of a collision. Be sure to wear the seat belt with the seat belt extender.


●The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury especially if the front passenger is very close to the airbag. The front passenger seat should be as far from the air- bag as possible with the seatback adjusted, so the front passenger sits upright.


●Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are safer for infants and children than the front passenger seat. (→P. 118)


●Do not sit on the edge of the seat or


lean against the dashboard.


109


1-7. Safety information


CAUTION


■SRS airbag precautions


110


●Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.


●Do not allow the front seat occupants to


hold items on their knees.


●Do not lean against the door, the roof side rail or the front, side and rear pil- lars.


●Do not allow anyone to kneel on the passenger seats toward the door or put their head or hands outside the vehicle.


●Do not attach anything to or lean any- thing against areas such as the dash- board, steering wheel pad and lower portion of the instrument panel. These items can become projectiles when the SRS driver, front passenger and knee airbags deploy.


1-7. Safety information


CAUTION


■SRS airbag precautions


●Do not attach anything to areas such as a door, windshield glass, side door glass, front or rear pillar, roof side rail and assist grip.


●Vehicles without a smart key system: Do not attach any heavy, sharp or hard objects such as keys and accessories to the key. The objects may restrict the SRS knee airbag inflation or be thrust into the driver's seat area by the force of the deploying airbag, thus causing a danger.


●Do not hang coat hangers or other hard objects on the coat hooks. All of these items could become projectiles and may cause death or serious injury, should the SRS curtain shield airbags deploy.


●If a vinyl cover is put on the area where the SRS knee airbag will deploy,


be sure to remove it.


●Do not use seat accessories which cover the parts where the SRS side airbags inflate as they may interfere with inflation of the airbags. Such accessories may prevent the side airbags from activating correctly, disable the system or cause the side airbags to inflate accidentally, resulting in death or serious injury.


●Do not strike or apply significant levels of force to the area of the SRS air-


bag components. Doing so can cause the SRS airbags to malfunction.


●Do not touch any of the component parts immediately after the SRS air-


bags have deployed (inflated) as they may be hot.


111


1-7. Safety information


CAUTION


■SRS airbag precautions


●If breathing becomes difficult after the SRS airbags have deployed, open a door or window to allow fresh air in, or leave the vehicle if it is safe to do so. Wash off any residue as soon as possible to prevent skin irritation.


●If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer.


■Modification and disposal of SRS airbag system components


Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury. ●Installation, removal, disassembly and repair of the SRS airbags ●Repairs, modifications, removal or replacement of the steering wheel, instrument panel, dashboard, seats or seat upholstery, front, side and rear pillars or roof side rails


●Repairs or modifications of the front fender, front bumper, or side of the


occupant compartment


●Installation of snow plows, winches, etc. to the front grille (bull bars or kan-


garoo bar etc.)


●Modifications to the vehicle's suspension system ●Installation of electronic devices such as mobile two-way radios and CD


players


●Modifications to your vehicle for a person with a physical disability


112


1-7. Safety information Front passenger occupant classification system


Your vehicle is equipped with a front passenger occupant classifica- tion system. This system detects the conditions of the front passen- ger seat and activates or deactivates the devices for the front passenger.


SRS warning light Seat belt reminder light “AIR BAG OFF” indicator light “AIR BAG ON” indicator light


113


1-7. Safety information


Condition and operation in the front passenger occupant classification system ■ Adult*1


Indicator/


warning light


“AIR BAG ON” and “AIR BAG OFF”


indicator lights


SRS warning light


Seat belt reminder light Front passenger airbag Side airbag on the front


passenger seat


Devices


Curtain shield airbag in the front


passenger side


Front passenger knee airbag


Front passenger’s seat belt pretensioner


■ Child*3 or child restraint system*4


Indicator/


warning light


“AIR BAG ON” and “AIR BAG OFF”


indicator lights


SRS warning light


Seat belt reminder light Front passenger airbag Side airbag on the front


passenger seat


Devices


Curtain shield airbag in the front


passenger side


“AIR BAG


ON” Off


Flashing*2


Activated


“AIR BAG OFF”*5


Off


Flashing*2
Deactivated


Activated


Front passenger knee airbag


Front passenger’s seat belt pretensioner


Deactivated Activated


114


1


1-7. Safety information


■ Unoccupied


Indicator/


warning light


“AIR BAG ON” and “AIR BAG OFF”


indicator lights


SRS warning light


Seat belt reminder light Front passenger airbag Side airbag on the front


passenger seat


Devices


Curtain shield airbag in the front


passenger side


“AIR BAG


OFF”


Off


Deactivated


Activated


Front passenger knee airbag


Front passenger’s seat belt pretensioner


Deactivated Activated


■ There is a malfunction in the system


Indicator/


warning light


“AIR BAG ON” and “AIR BAG OFF”


indicator lights


SRS warning light


Seat belt reminder light Front passenger airbag Side airbag on the front


passenger seats


Devices


Curtain shield airbag in the front


passenger side


“AIR BAG


OFF”


On


Deactivated


Activated


Front passenger knee airbag


Front passenger’s seat belt pretensioner


Deactivated Activated


*1: The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may rec- ognize him/her as a child depending on his/her physique and pos- ture. In the event the front passenger does not wear a seat belt.


*2: *3: When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/ her as an adult depending on his/her physique or posture.


115


1-7. Safety information


*4: Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 118) In case the indicator light is not illuminated, consult this manual on how to install the child restraint system properly. (→P. 122)


*5:


CAUTION


■Front passenger occupant classification system precautions


Observe the following precautions regarding the front passenger occupant classification system. Failure to do so may cause death or serious injury. ●Wear the seat belt properly. ●Make sure the front passenger’s seat belt plate has not been left inserted


into the buckle before someone sits in the front passenger seat.


●Make sure the “AIR BAG OFF” indicator light is not illuminated when using the seat belt extender for the front passenger seat. If the “AIR BAG OFF” indicator light is illuminated, disconnect the extender tongue from the seat belt buckle, and reconnect the seat belt. Reconnect the seat belt extender after making sure the “AIR BAG ON” indicator light is illuminated. If you use the seat belt extender while the “AIR BAG OFF” indicator light is illumi- nated, the SRS airbags for the passenger may not activate correctly, which could cause death or serious injury in the event of a collision. ●Do not apply a heavy load to the front passenger seat or equipment. ●Do not put weight on the front passenger seat by putting your hands or


feet on the front passenger seat seatback from the rear passenger seat.


●Do not let a rear passenger lift the front passenger seat with their feet or


press on the seatback with their legs.


●Do not put objects under the front passenger seat.


116


1


1-7. Safety information


CAUTION


■Front passenger occupant classification system precautions


●Do not recline the front passenger seatback so far that it touches a rear seat. This may cause the “AIR BAG OFF” indicator light to be illuminated, which indicates that the passenger’s airbags will not deploy in the event of a severe accident. If the seatback touches the rear seat, return the seat- back to a position where it does not touch the rear seat. Keep the front passenger seatback as upright as possible when the vehicle is moving. Reclining the seatback excessively may lessen the effectiveness of the seat belt system.


●If an adult sits in the front passenger seat, the “AIR BAG ON” indicator light is illuminated. If the “AIR BAG OFF” indicator is illuminated, ask the passenger to sit up straight, well back in the seat, feet on the floor, and with the seat belt worn correctly. If the “AIR BAG OFF” indicator still remains illuminated, either ask the passenger to move to the rear seat, or if that is not possible, move the front passenger seat fully rearward.


●When it is unavoidable to install a forward-facing child restraint system on the front passenger seat, install the child restraint system on the front pas- senger seat in the proper order. (→P. 122)


●Do not modify or remove the front seats. ●Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately.


●Child restraint systems installed on the rear seat should not contact the


front seatbacks.


●Do not use a seat accessory, such as a cushion and seat cover, that cov-


ers the seat cushion surface.


●Do not modify or replace the upholstery of the front seat.


117


1-7. Safety information Child restraint systems


A child restraint system for a small child or baby must itself be prop- erly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.


Points to remember


Studies have shown that installing a child restraint system on a rear seat is much safer than installing one on the front passenger seat. ● Choose a child restraint system that suits your vehicle and is


appropriate to the age and size of the child.


● For installation details, follow the instructions provided with the


child restraint system. General installation instructions are provided in this manual. (→P. 122)


118


1-7. Safety information


Types of child restraints


Child restraint systems are classified into the following 3 types according to the age and size of the child: Rear facing ⎯ Infant seat/convertible seat


Forward facing ⎯ Convertible seat


Booster seat


119


1-7. Safety information


■Selecting an appropriate child restraint system


●Use a child restraint system appropriate for the child until the child


becomes large enough to properly wear the vehicle’s seat belt.


●If the child is too large for a child restraint system, sit the child on a rear


seat and use the vehicle's seat belt. (→P. 69)


CAUTION


■Child restraint precautions


●For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle's interior. ●Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.


●Never install a rear-facing child restraint system on the front passenger seat even if the “AIR BAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear-facing child restraint system is installed on the front passenger seat.


●A forward-facing child restraint system may be installed on the front pas- senger seat only when it is unavoidable. A child restraint system that requires a top tether strap should not be used in the front passenger seat since there is no top tether strap anchor for the front passenger seat. Adjust the seatback as upright as possible and always move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illumi- nated, because the front passenger airbag could inflate with considerable speed and force. Otherwise, the child may be killed or seriously injured.


120


1


1-7. Safety information


CAUTION


■Child restraint precautions


●Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of a sudden stop, sudden swerve or accident.


●Do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front and rear pillars or roof side rails from which the SRS side airbags or SRS curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the SRS side airbags and curtain shield airbags inflate, and the impact could cause death or serious injury to the child.


●Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly secured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sudden stop, sudden swerve or an accident.


■When children are in the vehicle


Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.


■When the child restraint system is not in use


●Keep the child restraint system properly secured on the seat even if it is


not in use. Do not store the child restraint system unsecured in the passenger com- partment.


●If it is necessary to detach the child restraint system, remove it from the vehicle or store it securely in the trunk. This will prevent it from injuring passengers in the event of a sudden stop, sudden swerve or accident.


121


1-7. Safety information Installing child restraints


Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.


Child restraint LATCH anchors LATCH anchors are provided for the outer rear seats. (But- tons displaying the location of the anchors are attached to the seats.)


Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) (→P. 69)


122


1-7. Safety information


Anchor brackets (for top tether strap) An anchor bracket is provided for each rear seat.


Installation with LATCH system


Type A STEP 1


Widen the gap between the seat cushion and seatback slightly.


STEP 2


Canada only


Latch the hooks of the lower straps onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.


123


1-7. Safety information


Type B STEP 1


Widen the gap between the seat cushion and seatback slightly.


If


the buckles onto


the Latch LATCH anchors. the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. For owners in Canada: The symbol on a child restraint system indicates the presence of a lower connector system.


STEP 2


Canada only


124


1-7. Safety information


Installing child restraints using a seat belt (child restraint lock function belt)


■ Rear facing ⎯ Infant seat/convertible seat STEP 1


Place the child restraint system on the rear seat facing the rear of the vehicle.


STEP 2


STEP 3


Run the seat belt through the

Loading...
x