2010 Toyota Camry HV Owners Manual

SRS warning light

“AIR BAG

ON” Off

Front passenger’s seat belt reminder light

Flashing*2

Devices

Front passenger airbag Side airbag on the front

passenger seats

Curtain shield airbag in the front

passenger side

Front passenger’s seat belt pretensioner

Activated

■ Child*3 or child restraint system*4

Indicator/

warning light

“AIR BAG ON” and “AIR BAG OFF” indi-

cator lights

SRS warning light

Front passenger’s seat belt reminder light

Devices

Front passenger airbag Side airbag on the front

passenger seats

Curtain shield airbag in the front

passenger side

Front passenger’s seat belt pretensioner

“AIR BAG OFF”*5

Off

Flashing*2

Deactivated

Activated

105

1-8. Safety information

■ Unoccupied

Indicator/

warning light

Devices

“AIR BAG ON” and “AIR BAG OFF” indi-

cator lights

SRS warning light

Front passenger’s seat belt reminder light

Front passenger airbag Side airbag on the front

passenger seats

Curtain shield airbag in the front

passenger side

Not illuminated

Off

Deactivated

Activated

Front passenger’s seat belt pretensioner

Deactivated

■ There is a malfunction in the system

Indicator/

warning light

“AIR BAG ON” and “AIR BAG OFF” indi-

cator lights

SRS warning light

Front passenger’s seat belt reminder light

Devices

Front passenger airbag Side airbag on the front

passenger seats

Curtain shield airbag in the front

passenger side

Front passenger’s seat belt pretensioner

“AIR BAG

OFF” On Off

Deactivated

Activated

*1: The system judges a person of adult size as an adult. When a smaller adult sits in the front passenger seat, the system may rec- ognize him/her as a child depending on his/her physique and pos- ture.

*2: In the event the front passenger does not wear a seat belt. *3: When a larger child who has outgrown a child restraint system sits in the front passenger seat, the system may recognize him/ her as an adult depending on his/her physique or posture.

106

1-8. Safety information

*4: Never install a rear-facing child restraint system on the front pas- senger seat. A forward-facing child restraint system should only be installed on the front passenger seat when it is unavoidable. (→P. 109)

*5: In case the indicator is not illuminated, consult this manual as for

installing the child restraint system properly. (→P. 113)

CAUTION

■Front passenger occupant classification system precautions

Observe the following precautions regarding the front passenger occupant classification system. Failure to do so may cause death or serious injury. ●Wear the seat belt properly. ●Make sure the front passenger’s seat belt tab has not been left inserted

into the buckle before someone sits in the front passenger seat.

●Make sure the “AIR BAG OFF” indicator light is not illuminated when using the seat belt extender for the front passenger seat. If the “AIR BAG OFF” indicator light is illuminated, disconnect the extender tongue from the seat belt buckle, then reconnect the seat belt. Reconnect the seat belt extender after making sure the “AIR BAG ON” indicator light is illuminated. If you use the seat belt extender while the “AIR BAG OFF” indicator light is illumi- nated, the front passenger airbag and side airbag on the front passenger side may not activate correctly, which could cause death or serious injury in the event of collision.

●Do not apply a heavy load to the front passenger seat or equipment. ●Do not put weight on the front passenger seat by putting your hands or

feet on the front passenger seat seatback from the rear passenger seat.

●Do not let a rear passenger lift the front passenger seat with their feet or

press on the seatback with their legs.

●Do not put objects under the front passenger seat.

107

1-8. Safety information

CAUTION

■Front passenger occupant classification system precautions

●Do not recline the front passenger seatback so far that it touches a rear seat. This may cause the “AIR BAG OFF” indicator light to be illuminated, which indicates that the passenger’s airbags will not deploy in the event of a severe accident. If the seatback touches the rear seat, return the seat- back to a position where it does not touch the rear seat. Keep the front passenger seatback as upright as possible when the vehicle is moving. Reclining the seatback excessively may lessen the effectiveness of the seat belt system.

●If an adult sits in the front passenger seat, the “AIR BAG ON” indicator light is illuminated. If the “AIR BAG OFF” indicator is illuminated, ask the passenger to sit up straight, well back in the seat, feet on the floor, and with the seat belt worn correctly. If the “AIR BAG OFF” indicator still remains illuminated, either ask the passenger to move to the rear seat, or if that is not possible, move the front passenger seat fully rearward.

●When it is unavoidable to install the forward-facing child restraint system on the front passenger seat, install the child restraint system on the front passenger seat in the proper order. (→P. 113)

●Do not modify or remove the front seats. ●Do not kick the front passenger seat or subject it to severe impact. Other- wise, the SRS warning light may come on to indicate a malfunction of the detection system. In this case, contact your Toyota dealer immediately.

●Child restraint systems installed on the rear seat should not contact the

front seatbacks.

●Do not use a seat accessory, such as a cushion or seat cover, that covers

the seat cushion surface.

●Do not modify or replace the upholstery of the front seat.

108

1-8. Safety information Child restraint systems

A child restraint system for a small child or baby must be properly restrained on the seat with the lap portion of the lap/shoulder belt. The laws of all 50 states of U.S.A. and Canada now require the use of child restraint systems.

Points to remember

Studies have shown that installing a child restraint system on a rear seat is much safer than installing one to the front passenger seat. ● Choose a child restraint system that suits your vehicle and is

appropriate to the age and size of the child.

● For installation details, follow the instructions provided with the

child restraint system. General installation instructions are provided in this manual. (→P. 113)

109

1-8. Safety information

Types of child restraints

Child restraint systems are classified into the following 3 types according to the age and size of the child.

Rear facing ⎯ Infant seat/convertible seat

Forward facing ⎯ Convertible seat

Booster seat

110

1-8. Safety information

■Selecting an appropriate child restraint system

●Use a child restraint system appropriate for the child until the child

becomes large enough to properly wear the vehicle’s seat belt.

●If a child is too large for a child restraint system, sit the child on a rear

seat and use the vehicle's seat belt. (→P. 63)

CAUTION

■Child restraint precautions

●For effective protection in automobile accidents and sudden stops, a child must be properly restrained, using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a substitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle's interior. ●Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.

●Never install a rear-facing child restraint system on the front passenger seat even if the “AIR BAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear-facing child restraint system is installed on the front passenger seat.

●A forward-facing child restraint system may be installed on the front pas- senger seat only when it is unavoidable. A child restraint system that requires a top tether strap should not be used in the front passenger seat since there is no top tether strap anchor for the front passenger seat. Adjust the seatback as upright as possible and always move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illumi- nated, because the front passenger airbag could inflate with considerable speed and force. Otherwise, the child may be killed or seriously injured.

111

1-8. Safety information

CAUTION

■Child restraint precautions

●Do not use the seat belt extender when installing a child restraint system on the front or rear passenger seat. If installing a child restraint system with the seat belt extender connected to the seat belt, the seat belt will not securely hold the child restraint system, which could cause death or seri- ous injury to the child or other passengers in the event of a sudden stop, sudden swerve or collision.

●Do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front and rear pillars or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side air- bags and curtain shield airbags inflate, and the impact could cause death or serious injury to the child.

●Make sure you have complied with all installation instructions provided by the child restraint manufacturer and that the system is properly secured. If it is not secured properly, it may cause death or serious injury to the child in the event of a sudden stop, sudden swerve or an accident.

■Child restraint lock function belt precaution

Do not allow children to play with the child restraint lock function belt. If the belt becomes twisted around a child’s neck, it will not be possible to pull the belt out leading to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.

■When the child restraint system is not in use

●Keep the child restraint system properly secured on the seat even if it is not in use. Do not store the restraint unsecured in the passenger compart- ment.

●If it is necessary to detach the child restraint system, remove it from the vehicle or store it securely in the trunk. This will prevent it from injuring passengers in the event of a sudden stop, sudden swerve or accident.

112

1-8. Safety information Installing child restraints

Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the outside rear seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Chil- dren) system.

Child restraint LATCH anchors LATCH anchors are provided for the outside rear seats. (But- tons displaying the location of the anchors are attached to the seats.)

Seat belts equipped with a child restraint locking mecha- nism (ALR/ELR belts except driver’s seat belt) (→P. 63)

113

1-8. Safety information

Installation with LATCH system

Type A

Canada only

114

Anchor bracket (for top tether strap)

Anchor brackets are provided for all rear seats.

STEP 1

STEP 2

STEP 3

Widen the gap between the seat cushion and seatback slightly. Latch the hooks of the lower straps onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto top the tether strap anchor.

For owners in Canada: A symbol on a restraint system indicates the presence of a lower connector system.

1

Type B

Canada only

1-8. Safety information

STEP 1

STEP 2

STEP 3

Widen the gap between the seat cushion and seatback slightly. Latch the buckles onto the LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto top the tether strap anchor.

For owners in Canada: A symbol on a restraint system indicates the presence of a lower connector system.

115

1-8. Safety information

Installing child restraints using a seat belt (child restraint lock function belt)

■ Rear facing ⎯ Infant seat/convertible seat STEP 1

Place the child seat on the rear seat facing the rear of the vehi- cle.

Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted.

then allow

Fully extend the shoulder belt and to retract slightly in order to activate the ALR lock mode.

it

Lock mode allows the seat belt to retract only.

STEP 2

STEP 3

116

1

STEP 4

1-8. Safety information

While pushing the child seat down into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that in cannot be extended.

■ Forward facing ⎯ Convertible seat STEP 1

Place the child seat on the seat facing the front of the vehicle.

STEP 2

STEP 3

Run the seat belt through the child seat and insert the plate into the buckle. Make sure that the belt is not twisted.

it

then allow

Fully extend the shoulder strap and to retract slightly into the ALR lock mode. Lock mode allows the seat belt to retract only.

117

1-8. Safety information

STEP 4

While pushing the child seat into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. (→P. 119)

STEP 5

■ Booster seat STEP 1

Place the booster seat on the seat facing the front of the vehi- cle.

Sit the child in the booster seat. Fit the seat belt to the booster seat according to the manufac- turer's instructions and insert the plate into the buckle. Make sure that the belt is not twisted.

Check that the shoulder belt is correctly positioned over the child's shoulder, and that the lap belt is as low as possible. (→P. 63)

STEP 2

118

1-8. Safety information

Removing a child restraint installed with a seat belt

Push the buckle release button and fully retract the seat belt.

Child restraint systems with a top tether strap

STEP 1

STEP 2

Secure the child restraint using the seat belt or LATCH anchors. Remove the head restraint.

Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top tether strap.

Make sure the top tether strap is securely latched.

119

1-8. Safety information

■Laws and regulations pertaining to anchorages

The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to the SAE J1819.

CAUTION

■When installing a booster seat

Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode: (→P. 66) ALR mode causes the belt to tighten only which could cause injury or dis- comfort to the child.

120

1

1-8. Safety information

CAUTION

■When installing a child restraint system

Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of sudden braking, sudden swerving or an accident.

●If the driver's seat interferes with the child restraint system and prevents it from being attached correctly, attach the child restraint system to the right- hand rear seat.

●Adjust the front passenger seat so that it does not interfere with the child restraint system.

●Only put a forward-facing or booster child seat on the front seat when unavoidable. When installing a forward- facing or booster child seat on the front passenger seat, move the seat as far back as possible even if the “AIR BAG OFF” indicator light is illuminated. Fail- ing to do so may result in death or seri- ous injury if the airbags deploy (inflate).

121

1-8. Safety information

CAUTION

■When installing a child restraint system

●When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child's shoulder. The belt should be kept away from the child's neck, but not so that it could fall off the child's shoulder. Failing to do so may result in death or serious injury in the event of sudden braking, sudden swerving or an accident.

●Ensure that the belt and tab are securely locked and the seat belt is not

twisted.

●Push and pull the child seat from side to side and forward to be sure it is

secure.

●Follow all installation instructions provided by the child restraint system

manufacturer.

●When a child restraint system with a top tether strap is installed, do not install the head restraint. The head restraint may interfere with the top tether strap preventing secure installation of the child restraint system.

●Make sure to properly store the removed head restraint in a secure place

when you use the child restraint system on the rear seat.

■Do not use a seat belt extender

If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of sud- den braking, sudden swerving or a collision.

■To correctly attach a child restraint system to the anchors

When using the LATCH anchors, be sure that there are no foreign objects around the anchors and that the seat belt is not caught behind the child restraint system. Make sure the child restraint system is securely attached, or it may cause death or serious injury to the child or other passengers in the event of a sudden stop, sudden swerve or an accident.

122

2-2. Instrument cluster Gauges and meters

The following gauges, meters and displays illuminate when the “POWER” switch is in ON mode.

Engine coolant temperature gauge Displays the engine coolant temperature. Fuel economy meter Displays the current fuel consumption in analog form when the hybrid system is operating. When only the electric motor (traction motor) powers the vehicle, the needle indicates “E-MODE”. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Odometer/trip meter/instrument panel light control and trip meter reset button Switches between odometer and trip meter. Pushing and holding the button when the trip meter is being displayed will reset the trip meter. Instrument panel light control: →P. 145
Multi-information display →P. 150

144

2

2-2. Instrument cluster

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Brighter Darker When the headlight switch is turned on, the brightness will be reduced slightly unless the control dial fully clockwise.

turned

is

■Eco drive level

and

The brightness of the arcs around the fuel economy meter speedometer change according to the eco drive level. The higher the fuel economy, the brighter the light becomes. The eco drive level is also displayed on the multi-information display. (→P. 151)

Average fuel consumption

The brightness of the arcs

25 MPG or less (9.0 L/100km or more) 26 to 30 MPG (8.8 to 8.0 L/100km) 31 to 35 MPG (7.8 to 7.0 L/100km) 36 MPG or more (6.8 L/100km or less)

Does not illuminate Illuminates weakly Illuminates brightly Illuminates most brightly

145

2-2. Instrument cluster

NOTICE

■To prevent damage to the engine and its components

The gasoline engine may be overheating if the engine coolant temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place. Check the gasoline engine after it has cooled completely. (→P. 438)

146

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.

Instrument cluster

Center panel

147

2-2. Instrument cluster

■ Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

Turn signal indicator (→P. 141)

Headlight high beam indicator (→P. 155)

(if equipped) *1

*1

Slip indicator (→P. 166)

Front fog light indicator (→P. 158)

SRS airbag on-off indi- cator (→P. 104)

Cruise control indicator (→P. 161)

Cruise control set indi- cator (→P. 161)

Shift position indicators (→P. 139)

Immobilizer indicator (→P. 87)

Driving ready indicator (→P. 135)

Headlight indicator (→P. 154)

Tail light indicator (→P. 154)

(if equipped)

(U.S.A.)

(CANADA)

148

2-2. Instrument cluster

■ Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 397)

*1, 3

*1, 2

*1

*1, 3

*1, 2

*1

*1

*1, 3

*1, 2

*1, 2

(red indicator) *1

(yellow indicator)

*1: These lights turn on when the “POWER” switch is turned to ON mode to indicate that a system check is being performed. They will turn off after the hybrid system is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.

*2: For vehicles sold in U.S.A. *3: For vehicles sold in Canada

CAUTION

■If a safety system warning light does not come on

Should a safety system light such as the ABS or the SRS warning light not come on when you start the hybrid system, this could mean that these sys- tems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

149

2-2. Instrument cluster Multi-information display

The multi-information display presents the driver with a variety of driving-related data, including the outside temperature.

● Outside

temperature dis- (→P. 151) play Indicates the outside tempera- ture.

● Trip information

(→P. 151) Displays driving range, fuel consumption and other cruis- ing-related information.

● Warning messages

(→P. 406) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.

● Odometer and trip meter

display Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the dis- tance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances indepen- dently.

150

Switch the display

2-2. Instrument cluster

Display items can be switched by pressing the “DISP” button.

The display will return to the out- side temperature display when the “DISP” button is pressed and held.

● Outside temperature

● Cruising range

Displays the outside air temperature.

The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C).

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining.

• This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed. • When only a small amount of fuel is added to the

tank, the display may not be updated.

● Average fuel consumption

Displays the average fuel consumption since the function was reset.

The function can be reset by pressing the “DISP” but- ton for longer than one second when the average fuel consumption is displayed.

151

2-2. Instrument cluster

● Driving distance

Displays the driving distance since the hybrid sys- tem was started.

● Average vehicle speed

Displays the average vehicle speed since the hybrid system was started.

● Cruise information off

Displays the odometer and trip meters only.

● Zoom display of odometer and trip meter

Displays the odometer and one of the trip meters simultaneously.

● Energy monitor

● Eco drive level

152

Displays the operating condition of the hybrid sys- tem. (→P. 27)

Displays the eco drive level and the average fuel consumption since the hybrid system was started. When the eco drive level increases, the eco drive level display may appear on the display, even if other information is currently being shown. This does not indicate a malfunction.

2-2. Instrument cluster

■Outside temperature display

In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change. ●When stopped, or driving at low speeds (less than 12 mph [20 km/h]) ●When the outside temperature has changed suddenly (at the entrance/

exit of a garage, tunnel, etc.)

NOTICE

■The multi-information display at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.

153

2-3. Operating the lights and wipers Headlight switch

The headlights can be operated manually or automatically.

For U.S.A.

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. The headlights and parking lights turn on and off automatically. (When the “POWER” switch is turned to ON mode) Daytime running light system is off.

154

2

For Canada

2-3. Operating the lights and wipers

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. The headlights and parking lights turn on and off automatically. (When the “POWER” switch is turned to ON mode)

Turning on the high beam headlights

With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release the lever to turn them off. You can flash the high beams with the headlights on or off.

155

2-3. Operating the lights and wipers

■Daytime running light system

To make your vehicle more visible to other drivers, the headlights turn on automatically (at a reduced intensity) whenever the hybrid system is started and the parking brake is released. Daytime running lights are not designed for use at night. For U.S.A.: Daytime running lights can be turned off by operating the switch.

■Headlight control sensor

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. the sensor Doing so detecting the level of ambient light and may cause the automatic headlight sys- tem to malfunction.

interferes with

■Automatic light off system

●When the headlights are on: The headlights and tail lights turn off 30 sec- onds after all doors are closed with the “POWER” switch OFF. (The lights turn off immediately if on the key is pressed after all doors are locked.)

●When only the tail lights are on: The tail lights turn off automatically if the “POWER” switch is turned to ACCESSORY mode or turned OFF and the driver’s door is opened.

●If any of the doors or trunk lid is left open, the lights automatically turn off

after 20 minutes.

To turn the lights on again, turn the “POWER” switch to ON mode, or turn the headlight switch off and then back to

position.

or

■Customization that can be configured at Toyota dealer

Settings of light sensor sensitivity can be changed. (Customizable features →P. 470)

156

2-3. Operating the lights and wipers

NOTICE

■To prevent the 12-volt battery from being discharged

Do not leave the lights on longer than necessary when the hybrid system is off.

157

2-3. Operating the lights and wipers Fog light switch∗

The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam.

Off Front fog lights on

158

∗: If equipped

2-3. Operating the lights and wipers Windshield wipers and washer

Wiper intervals can be adjusted for intermittent operation.

windshield

Intermittent wiper operation Low speed windshield wiper operation High wiper operation Temporary operation

speed windshield

the

Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency

159

2-3. Operating the lights and wipers

Wash/wipe operation

Wipers operate automatically.

■The windshield wipers and washer can be operated when

The “POWER” switch is in ON mode.

■If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

■When the windshield is dry

Do not use the wipers, as they may damage the windshield.

■When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.

■When a nozzle becomes blocked

Do not try to clear it with a pin or other object. The nozzle will be damaged.

160

2-4. Using other driving systems Cruise control

Use the cruise control to maintain a set speed without using the accelerator.

Indicators Cruise control switch

■ Setting the vehicle speed STEP 1

STEP 2

Turn the “ON-OFF” button on. At this time, the cruise control indicator will come on. Press the button once more to deactivate the cruise control.

Accelerate or decelerate to the desired speed and push the lever down to set the cruise control speed.

At this time, the cruise control set indicator will come on.

161

2-4. Using other driving systems

■ Adjusting the speed setting

Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pushing the lever up or down and releasing it.

■ Canceling and resuming regular acceleration

Cancel Pull the lever towards you to cancel cruise control. The speed setting is also can- celed when the brakes are applied. Resume To resume cruise control and return to the set speed, push the lever up.

162

2-4. Using other driving systems

■Cruise control can be set when

●The shift lever is in D. ●Vehicle speed is between approximately 25 mph and 125 mph (40 km/h

and 200 km/h).

■Accelerating

The vehicle can be accelerated normally. After acceleration, the set speed resumes.

■Automatic cruise control cancellation

The set speed is automatically canceled in any of the following situations. ●Actual vehicle speed falls more than 10 mph (16 km/h) below the preset

vehicle speed. At this time, the memorized set speed is not retained.

●Actual vehicle speed is below 25 mph (40 km/h). ●VSC is activated.

■If the cruise control indicator light flashes

Press the “ON-OFF” button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Contact your Toyota dealer and have your Toyota inspected.

163

2-4. Using other driving systems

CAUTION

■To avoid operating the cruise control by mistake

Keep the “ON-OFF” button off when not in use.

■Situations unsuitable for cruise control

Do not use cruise control in any of the following situations. Doing so may result in control of the vehicle being lost and could cause an accident resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills

164

2

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■ ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

■ Brake assist

Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation.

■ VSC (Vehicle Stability Control)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

■ TRAC (Traction Control)

Maintains drive power and prevents the front wheels from spinning when starting the vehicle or accelerating on slippery roads.

■ EPS (Electric Power Steering)

Employs an electric motor to reduce the amount of effort needed to turn the steering wheel.

■ VDIM (Vehicle Dynamics Integrated Management)

Provides integrated control of the ABS, VSC, TRAC and EPS systems. Maintains vehicle stability when swerving on slippery road surfaces by controlling the brakes, hybrid system output, and steering assist.

165

2-4. Using other driving systems

When VSC and TRAC are operating

If the vehicle is in danger of slip- ping or the front wheels spin, the indicator flashes to indicate that VSC/TRAC have been engaged. A buzzer (intermittent) sounds to indicate that VSC is operating.

■Sounds and vibrations caused by ABS, brake assist, VSC and TRAC ●A sound may be heard from the engine compartment when the hybrid system is started or just after the vehicle begins to move. This sound does not indicate that a malfunction has occurred in any of these sys- tems.

●Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop.

■Reduced effectiveness of EPS

The effectiveness of EPS is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the hybrid system off. The system should return to normal within 10 minutes.

■If the slip indicator comes on...

It may indicate a malfunction in the VSC and TRAC. Contact your Toyota dealer.

166

2

2-4. Using other driving systems

CAUTION

■ABS does not operate effectively when

●Tires with inadequate gripping ability are used (such as excessively worn

tires on a snow covered road).

●The vehicle hydroplanes while driving at high speed on the wet or slick

road.

■Stopping distance when ABS is operating on the wet or slick roads

ABS is not designed to shorten the vehicle's stopping distance. Always maintain a safe distance from the vehicle in front of you in the following situ- ations. ●When driving on dirt, gravel or snow-covered roads ●When driving with tire chains ●When driving over bumps in the road ●When driving over roads with potholes or uneven roads

■TRAC may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the TRAC system is operating. Do not drive the vehicle in conditions where stability and power may be lost.

167

2-4. Using other driving systems

CAUTION

■When VSC is activated

The slip indicator light flashes and a warning buzzer sounds. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes and a buzzer sounds.

■Replacing tires

Make sure that all tires are of the same size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the recom- mended tire pressure level. The ABS and VSC system will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.

■Handling of tires and suspension

Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.

168

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the trunk whenever possible. ● Be sure all items are secured in place. ● Be careful to keep the vehicle level. Placing the weight as far for-

ward as possible helps maintain vehicle balance.

● For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) Steps for Determining Correct Load Limit ⎯ (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehi- cle’s placard.

(2) Determine the combined weight of the driver and passengers

that will be riding in your vehicle.

(3) Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4) The resulting figure equals the available amount of cargo and

luggage load capacity. For example, if the XXX amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of avail- able cargo and luggage load capacity is 650 lbs. (1400 - 750
(150 × 5) = 650 lbs.)

(5) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

169

2-5. Driving information

(6)

If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing.

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 900 lb. (410
kg), the available amount of cargo and luggage load capacity will be as follows: 900 lb. - 366 lb. = 534 lb. (410 kg -166 kg = 244 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

534 lb. - 388 lb. = 146 lb. (244 kg - 176 kg = 68 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

170

2

2-5. Driving information

CAUTION

■Storage precautions

Observe the following precautions. Failing to do so may result in death or serious injury. ●To prevent cargo and luggage from sliding forward during braking, do not stack anything in the enlarged trunk. Keep cargo and luggage low, as close to the floor as possible.

●Never allow anyone to ride in the enlarged trunk. It is not designed for passengers. They should ride in their seats with their seat belts prop- erly fastened. Otherwise, they are much more likely to suffer death or serious bodily injury, in the event of sudden braking, sudden swerving or a collision.

●Do not place cargo or luggage in or on the following locations as the item may get under the brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident. • Driver’s feet • Front passenger or rear seats (when stacking items) • Package tray • Instrument panel • Dashboard

●Secure all items in the occupant compartment, as they may shift and injure someone during sudden braking, sudden swerving or an acci- dent.

■Capacity and distribution

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant's weight and the cargo load is less

than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking con- trol which may cause death or serious injury.

171

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. ■ Total load capacity: 900 lb. (410 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

■ Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person.

■ Towing capacity

Toyota does not recommend towing a trailer with your vehicle.

■ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 361)

CAUTION

■Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

172

2

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations

● Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine/power control unit coolant • Washer fluid

● Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. ■ Before driving the vehicle

Perform the following according to the driving conditions. ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. ● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

● Remove any ice that has accumulated on the vehicle chassis. ● Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

173

2-5. Driving information

■ When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

■ When parking the vehicle

Park the vehicle and move the shift lever to P without setting the parking brake. The parking brake may freeze up, preventing it from being released.

Selecting tire chains

Use the correct tire chain size when mounting the snow chains. Chain size is regulated for each tire size.

Side chain:

0.12 in. (3 mm) in diameter 0.39 in. (10 mm) in width 1.18 in. (30 mm) in length

Cross chain:

0.16 in. (4 mm) in diameter 0.55 in. (14 mm) in width 0.98 in. (25 mm) in length

Regulations on the use of snow chains

● Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains.

● Install the chains on the front tires. ● Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

174

2-5. Driving information

■Tire chains

Observe the following precautions when installing and removing chains. ●Install and remove tire chains in a safe location. ●Install tire chains on the front tires only. Do not install tire chains on rear

tires.

●Install tire chains following the instructions provided in the accompanying

manual.

CAUTION

■Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the size specified for your vehicle. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

●Use snow tires on all, not just some wheels.

■Driving with tire chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden turns and braking, as use of chains may adversely affect

vehicle handling.

●Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

175

2-5. Driving information

NOTICE

■Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

■Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

176

2-5. Driving information Trailer towing

Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your Toyota is not designed for trailer towing or for the use of tow hitch mounted carriers.

177

2-5. Driving information Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

178

2-5. Driving information

179

3-1. Using the air conditioning system and defogger Automatic air conditioning system

Air outlets are automatically selected and fan speed is automatically adjusted according to the temperature setting.

Air outlet display

Fan speed display

Driver’s side temperature setting display Driver’s side temper- ature control

“DUAL” button

Front passenger’s side temperature setting display

Change the air outlets used (air flow selector button)

Front passenger’s side temperature control

Automatic mode

Off

Windshield defogger

Air conditioning on/off switch

Fan speed (fan speed selector)

Outside air or recirculated air mode

■ “ECO HEAT/COOL” switch “ECO HEAT/COOL” mode enables the air conditioning to be oper- ated at a reduced capacity in order to limit use of the hybrid battery (traction battery). The effectiveness of the air conditioning will be lower than normal.

On/off

“ECO HEAT/COOL” When mode is turned on, the switch indicator will come on and the “ECO” indicator will appear on the air conditioning display.

182

3-1. Using the air conditioning system and defogger

Using the automatic mode

STEP 1

Press The air conditioning system will begin to operate. Air outlets and fan speed are automatically adjusted according to the temperature setting.

STEP 2

Turning

to the right increases the temperature and

to the left decreases the temperature on the

turning driver’s side. The temperature for the driver and passenger seats can be set sep- arately.

Adjusting the settings

■ Adjusting the temperature setting

Turning

to the right increases the temperature and turning

to the left decreases the temperature on the driver’s side.

Turning to the left (decrease) on the passenger’s side to separately adjust the temperature for the pas-

to the right (increase) or

senger’s and driver’s side (dual mode). Press to return the driver's and passenger side temperatures to the same setting (simulta- neous mode). The air conditioning system switches between dual and simultaneous

mode each time

is pressed.

183