2007 Toyota Camry HV Owners Manual

D Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.

D Since the mirror surfaces can get hot, do not touch them when the defogger switch is on.

NOTICE

The outside rear view mirrors are fixed in place. Do not try to fold the mirrors. It may damage the mirrors.

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Push (right).

the switch to “L” (left) or “R”

2. Control switch—To move

the mirror Push the switch in the desired direc- tion. Mirrors can be adjusted when “POWER” switch is set at ACC or ON.

the

115

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Anti−glare inside rear view mirror

Auto anti−glare inside rear view mirror

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

116

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. This mirror is equipped with auto anti− glare function. The function is designed to reduce glare from the headlights of the vehicle behind you during night driving. When the “POWER” switch is set at ON, the inside rear view mirror always turns on in the automatic function mode. The indicator illuminates to show you that the function is on.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Vanity mirrors

to reduce

In automatic function mode, if the mirror detects light from the headlights of the the mirror surface vehicle behind you, darkens slightly the reflected light. To turn off and on the automatic function, push the “AUTO” switch. Adjust it before driving so that the rear view is in the best condition. When the inside air temperature is low, it may take a little longer for the mirror to darken the detection of headlights.

in response

to

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

To ensure correct functioning of anti− glare mirror sensors located on both sides of the mirror, do not touch or cover the sensors with your finger or a piece of cloth, etc.

To use the vanity mirror, swing down the sun visor and slide the cover. On some models—The when you slide the cover.

lights come on

117

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

118

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 1− 5

OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Emergency flashers Instrument panel light control Interior light Personal lights Illuminated entry system Windshield wipers and washer Rear window and outside rear view mirror defoggers

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

120
125
126
126
127
127
128
129

119

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Headlights and turn signals (for the U.S.A.)

tail

the

When the tail lights/headlights are turned on, the brightness of the instrument clus- ter will be reduced slightly unless the in- strument panel light control knob is turned fully clockwise. However, the brightness of the instrument cluster will not be reduced in daytime lights/headlights are even when turned on. Automatic operation— To turn on or off the lights automatical- ly, twist the headlight/turn signal lever knob to the “AUTO” position when the “POWER” switch is set at ON. The headlights and/or all of the lights in position 1 automatically turn on or off de- pending on the darkness of the surround- ings. Manually twist the knob to the position 2
to turn on the headlights if they are need- ed immediately when entering a dark tun- nel, parking structure, etc.

HEADLIGHTS Manual operation— To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above The headlight instrument cluster.

lights up in the

license plate,

indicator

tail,

the

120

The automatic light control sensor is on the top of the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor. If you feel that the automatic light control comes into operation too early or too late, have the sensor adjusted by your Toyota dealer.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

is opened and closed after

Automatic light cut off system Position 1 or “AUTO” position with the tail lights on— The lights automatically turn off when the driver’s door is opened after the “POWER” switch is turned off. Position 2 or “AUTO” position with the headlights on— The lights automatically turn off after 30
seconds when any of the doors or trunk lid the “POWER” switch is turned off. The lights can be turned off immediately by pushing the lock switch on the elec- tronic key with all the doors locked and the trunk lid closed. The time period before the lights turn off can be changed. For details, ask your Toyota dealer. If any of the doors or trunk lid is left open, the lights automatically turn off after 20 minutes. To the “POWER” switch at ON or actuate the headlight switch. If you are going to park for over one week, make sure the knob is in the “DRL OFF” position.

lights again, set

turn on

the

’07Camry hybrid_U (L/O 0610)

NOTICE

To prevent the 12 volt battery from being discharged, do not leave the lights on for a long period when the hybrid system is turned off.

Daytime Running Light (DRL) system The Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many differ- ent driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. The DRL system will make your headlights come on at a reduced brightness when: D The “POWER” switch is set at ON with

the hybrid system turned on.

D The light switch is in the “AUTO” posi- tion with the headlights off or position 1.

D The parking brake is released. To turn on the other exterior lights and instrument panel lights, twist the knob to position 1. Twist the knob to position 2 to turn the headlights to full intensity for night driving. To turn off the DRL system, twist the knob to the position 3 (“DRL OFF”) or turn the “POWER” switch off. The daytime running light system can be disabled. For details, contact your Toyota dealer.

121

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Headlights and turn signals (for Canada)

High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights even when the headlights are off.

the lever all

122

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The “POWER” switch must be set at ON. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs” on page 373 in Section 7−3.

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights The tail light indicator (green light) on the instrument panel will tell you that the tail lights are on. Position 2—Headlights and all of above Position 3 (“AUTO”)—Headlights and all of the lights in the position 1
They automatically turn on or off depend- ing on the darkness of the surroundings.

the

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Manually twist the knob to the position 2
to turn on the headlights if they are need- ed immediately when entering a dark tun- nel, parking structure, etc. When the tail lights/headlights are turned on, the brightness of the instrument clus- ter will be reduced slightly unless the in- strument panel light control knob is turned fully clockwise. However, the brightness of the instrument cluster will not be reduced in daytime even when lights/headlights are turned on.

the

tail

’07Camry hybrid_U (L/O 0610)

The automatic light control sensor is on the top of the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor. If you feel that the automatic light control comes into operation too early or too late, have the sensor adjusted by your Toyota dealer.

is opened and closed after

Automatic light cut off system Position 1 or position 3 with the tail lights on— The lights automatically turn off when the driver’s door is opened after the “POWER” switch is turned off. Position 2 or position 3 with the head- lights on— The lights automatically turn off after 30
seconds when any of the doors or trunk lid the “POWER” switch is turned off. The lights can be turned off immediately by pushing the lock switch on the elec- tronic key with all the doors locked and the trunk lid closed. The time period before the lights turn off can be changed. For details, ask your Toyota dealer. If any of the doors or trunk lid is left open, the lights automatically turn off after 20 minutes. To the “POWER” switch at ON or actuate the headlight switch. If you are going to park for over one week, make sure the knob is in the “OFF” position.

lights again, set

turn on

the

123

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

NOTICE

To prevent the 12 volt battery from being discharged, do not leave the lights on for a long period when the hybrid system is turned off.

Daytime Running Light (DRL) system The Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many differ- ent driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. The DRL system will make your headlights come on at a reduced brightness when: D The “POWER” switch is set at ON with

the hybrid system turned on.

is

D The knob

“OFF” position, position 1 or position 3 with the head- lights off.

the

in

D The parking brake is released. To turn on the other exterior lights and instrument panel lights, twist the knob to position 1. Twist the knob to position 2 to turn the headlights to full intensity for night driving.

124

High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Emergency flashers

NOTICE

To prevent the 12 volt battery from being discharged, do not leave the switch on longer than necessary when the hybrid system is turned off.

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The “POWER” switch must be set at ON. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs” on page 373 in Section 7−3.

flashers,

turn on

the emergency

To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.

125

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Instrument panel light control

Interior light

Without moon roof

To adjust the brightness of the instru- ment panel lights, turn the knob. With the knob turned fully clockwise, the intensity of the instrument cluster lights will not be reduced even when the tail lights/headlights are turned on.

126

With moon roof

’07Camry hybrid_U (L/O 0610)

To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when the illu- minated entry system acts. For details, see “Illuminated entry system” on page 127 in this Section.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Personal lights

FRONT PERSONAL LIGHTS To turn on light, push the lens. To turn it off, push the lens once again.

the front personal

REAR PERSONAL LIGHTS (vehicles with moon roof) To turn on the rear personal light, push the switch. To turn it off, push the switch once again. By gently adjusting the shade of the rear personal light, you can change the direc- tion of the light to suit your preference. When either of is opened, the light on that side turns on automatically. Closing the rear side doors will turn the lights off.

the rear side doors

interior

light and

the doors are closed and

Illuminated entry system The the “POWER” switch light come on and remain on for about 15 seconds when you carry the registered key into the entry function actuation area. For further information of entry function actuation area, see “Smart key system” on page 32 in Sec- tion 1−2. If all the “POWER” switch is set at ACC or ON, the lights will fade out. If all the doors are locked, the lights will fade out. To prevent the 12 volt battery being dis- charged, all of the lights will automatically turn off when is turned off, and the door is left opened for about 20 minutes. When any of the doors are unlocked with wireless remote control function or me- chanical key, the lights will come on and remain on for about 15 seconds before fading out. When any of the doors are opened, the lights will come on and remain on for about 15 seconds before fading out.

“POWER” switch

the

127

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Windshield wipers and washer

the doors are closed, when

If all the “POWER” switch is turned off, the lights will come on and remain on for about 15
seconds. This feature can be disabled and the dura- tion of the lighting can be changed. For details, ask your Toyota dealer.

To turn on the windshield wipers, move the lever to the desired setting. The “POWER” switch must be set at ON.

Lever position

Operation

Position 1

Position 2

Position 3

Position 4

Position 5

Intermittent operation

Low speed operation

High speed operation

Single sweep operation

Washer on

the band upward

Rotating the band on the lever lets you adjust the wiper time interval when the wiper lever is in the intermittent position (position 1). Twist to increase the time between sweeps, and downward to decrease it. To spray washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer sprays. For instructions on adding washer fluid, see “Adding washer fluid” on page 373 in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield the glass.

It may scratch

is dry.

128

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

When waxing your vehicle, make sure that the washer nozzles do not become blocked. If a nozzle becomes blocked, contact your Toyota dealer to have the vehicle serviced.

NOTICE

If a nozzle becomes blocked, do not try to clear it with a pin or other object. The nozzle will be damaged.

’07Camry hybrid_U (L/O 0610)

Rear window and outside rear view mirror defoggers

To defog or defrost the rear window, push the switch. The “POWER” switch must be set at ON. The thin heater wires on the inside of the rear window will quickly clear the sur- faces. An indicator light will illuminate to indicate the defogger is operating. Heater panels mirrors will also quickly clear faces. Push the switch once again to turn the defogger off.

the outside rear view the sur-

in

The system will automatically shut off when the operation time has been com- pleted. The operation time is between 15
minutes and 1 hour depending on the am- bient temperature and vehicle speed.

CAUTION

Since the mirror surfaces can get hot do not touch them when the defogger switch is on.

turn

the defoggers off Make sure you when the surfaces are clear. Leaving the defoggers on for a long time could cause the 12 volt battery to discharge, especially during stop−and−go driving. The defoggers are not designed for drying rain water or for melting snow. If the outside rear view mirrors are heavi- ly coated with ice, use a spray de−icer before operating the switch.

NOTICE

When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.

129

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

130

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 1− 6

OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel gauge Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel economy meter Multi−information display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzers

132
132
133
134
150

131

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Fuel gauge

Engine coolant temperature gauge

If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.

indicates

The gauge the approximate quantity of fuel remaining in the tank when the “POWER” switch is set at ON. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual.

132

The gauge indicates the engine coolant temperature when the “POWER” switch is set at ON. The engine operating tem- perature will vary with changes in weather and engine load. 1. Red zone 2. Blue zone If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Fuel economy meter

When the needle is in the blue zone, the coolant temperature is cold. Heat may not be available while the coolant temperature is the blue zone. Your vehicle may overheat during severe operating conditions, such as: D Driving up a long hill on a hot day. D Reducing speed or stopping after high

speed driving.

D Idling for a long period with the air conditioning on in stop−and−go traffic.

NOTICE

z Do not remove the thermostat

in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.

z Do not continue driving with an overheated engine. See “If your ve- hicle overheats” on page 317 in Section 4.

fuel consumption

The fuel economy meter indicates the current in analog form when the engine is running. When only the traction motor powers the ve- hicle, the needle indicates “E MODE”. D The needle may indicate the best rate on the meter when the engine is run- ning but the fuel is not consumed.

D The needle may indicate the best rate on the meter when fuel consumption is less than the indicated value.

D The needle may indicate the worst rate on the meter when fuel consumption is more than the indicated value.

133

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

CAUTION

Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

Multi−information display— The following information is displayed on the multi−information display when the “POWER” switch is set at ON. D Outside temperature and cruise in-

formation

D Odometer and two trip meters D Messages During ordinary driving, the information is displayed. However, in case the vehicle has a system malfunction or if there is some information that the driver should be informed of, a message appears on the display. See “—Messages” on page 140
for details. If the electrical power source has been disconnected from the cruise information display, the display will automatically be set to the initial mode. When lights are turned on, the brightness of the display will be reduced.

instrument panel

the

At extremely low temperatures, the mul- ti−information display may respond slow- ly.

134

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

—Outside temperature and cruise information

Each time you push the “DISP” button, the display toggles through the follow- ing information. 1. Outside temperature 2. Cruising range 3. Average fuel consumption after refuel-

ing

4. Driving distance 5. Average vehicle speed 6. Cruise information off 7. Zoom display of odometer and trip me-

ter

8. Energy monitor 9. Eco drive level The display will return to the outside tem- perature display with pushing and holding the “DISP” button for 1 second. The displayed values in the cruise infor- mation display indicate general driving conditions. Accuracy varies with driving habits and road conditions. When the “POWER” switch is set at ON, the last previously used mode displayed just before the “POWER” switch is turned off will appear.

135

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

1. Outside temperature

(“OUTSIDE TEMP”)

2. Driving range

(“CRUISING RANGE”)

It

the

fuel

indicates

fuel gauge reaches “E”.

The distance the vehicle can travel with the remaining is calculated and displayed based on the quantity of re- maining fuel and past fuel consumption. The driving range display the approximate distance that you can drive until is different from the actual distance traveled. If the fuel gauge malfunctions, the mileage figure will not appear. When the vehicle is refueled, the driving range is recalculated. The actual driving range varies with driv- ing habits and road conditions. If fuel con- sumption is good, the driving range will be longer than indicated. If fuel consumption is poor, the driving range will be shorter than indicated. If the low fuel level warning light comes on, refuel the vehicle even if the display indicates that the vehicle can be driven further.

from

indi-

temperature

The outside temperature display cates the outside air temperature. The displayed ranges −40_C (−40_F) up to 50_C (122_F). If an abnormality exists in the connection of the outside air temperature sensor, “−−” or “E” will appear on the display. If “−−” or “E” appears on the display, contact your Toyota dealer. There may be a case that “−−” appears momentarily when the “POWER” switch is quickly set to ON. It is normal if it goes out soon.

136

3. Average fuel consumption after re-

fueling (“TANK AVG”)

Average fuel consumption after refuel- ing is calculated and displayed based on total driving distance and total fuel consumption. Every time you refuel the vehicle, the dis- played value is reset. 4. Driving distance (“SINCE START”)

The driving distance after the hybrid system started is displayed. Every time you turn on the hybrid system, the driving distance display is reset. 5. Average vehicle speed

(“AVG SPEED”)

Average vehicle speed is calculated and displayed based on total driving dis- tance and total driving time.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

6. Cruise information off The display indicates only odometer and two trip meters. 7. Zoom display of odometer and trip

meter

displayed

simultaneously. two

The odometer and one of the trip meters are See trip meters” de- “—Odometer and scribed below. 8. Energy monitor The operating condition of the hybrid system appears on the display. See “Energy monitor” on page 3 for de- tails.

9. Eco drive level The eco drive level is visually displayed on the multi−information display, and it indicates the average fuel consumption after the hybrid system is turned on. In accordance with the average fuel con- sumption, the levels are displayed as follows: Level 0—25 MPG or less or

9.0 L/100 km or more

Level 1—26 to 30 MPG or

8.8 to 8.0 L/100 km

Level 2—31 to 35 MPG or

7.8 to 7.0 L/100 km

Level 3—36 MPG or more or

6.8 L/100 km or less

The brightness of the arcs around the fuel economy meter and speedometer change according to the eco drive level. The high- er the fuel economy, the brighter the light becomes. Level 0—Does not illuminate Level 1—Illuminates weakly Level 2—Illuminates brightly Level 3—Illuminates most brightly This function works even if a display other than the eco drive level is shown on the multi−information display.

137

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

—Odometer and two trip meters

Normal display

the zoom display of trip meter when

This meter displays the odometer and two trip meters. the Selecting odometer and the cruise information is displayed causes the odometer and one of the trip me- ters to be displayed simultaneously. 1. Odometer—Shows

total distance

the

the vehicle has been driven.

2. Two

trip meters—Show

two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.

fuel economy and

the other

level

for a

is displayed

When the hybrid system is turned off, the eco drive few seconds to show the average fuel con- sumption for the most recent trip. If the average fuel consumption is in level 3, “EXCELLENT!” is simultaneously dis- played under the eco drive level.

138

Zoom display

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter then back B, the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.

to

139

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Status

Action

Parking brake is not released.

Release parking brake.

Engine oil pressure is low.

Stop and check.

Hybrid system malfunction is detected.

Stop your vehicle and call a Toyota dealer.

Coolant temperature is high.

Stop your vehicle immediately.

The temperature for the inverter, traction motor or motor generator is high.

Stop your vehicle immediately.

—Messages

Message

140

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Message

Status

Action

Any of doors are opened.

Close doors completely.

Trunk is opened.

Close trunk completely.

Malfunction of VSC function is detected.

Take vehicle to your Toyota dealer.

Transmission is out of the “P” position when starting the hybrid system.

Shift the transmission to the “P” position when starting the hybrid system.

141

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Message

Status

Action

Hybrid battery is discharged or its voltage is low.

Stop and check.

Transmission selector lever is not set “P” position.

Shift the transmission selector lever to “P” position.

Brake pedal is not depressed when starting the hybrid system.

Depress brake pedal firmly.

Transmission selector lever is not set “P” position.

Shift the transmission selector lever to “P” position.

D “POWER” switch is not turned off when getting out

D Turn hybrid system off.

vehicle carrying the electronic key.

D Electronic key is not detected in the vehicle when

D Confirm that the key is in the vehicle.

“POWER” switch is set at ON.

Electronic key battery is low.

Replace key battery.

Steering lock system malfunction is detected.

Contact your Toyota dealer.

142

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Message

Status

Action

Steering lock is stuck.

Turn steering wheel slightly.

Oil change is nearly due.

Check engine oil.

Oil change is due.

Change engine oil.

Washer fluid level is low.

Add washer fluid.

Moon roof is opened with “POWER” switch turned off. Close moon roof.

Fuel door is left open.

Close the fuel door.

143

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(a)

(c)

(e)

This message is to warn the driver that the temperature for the inverter, trac- tion motor or motor generator is too high. Stop the vehicle and allow the the in- verter, traction motor and motor gener- ator to cool. See “If your vehicle over- heats” on page 317 in Section 4. the master The message appears with warning light and a warning tone sounds.

NOTICE

Do not continue driving with the mes- sage displayed.

This message is to warn the driver that the parking brake is not completely re- leased at the vehicle speed of 5 km/h (3 mph) or more. Stop the vehicle and release the park- ing brake fully. The message appears with the master warning light and a warning tone sounds.

This message is to warn the driver that the hybrid system is malfunctioning. If a malfunction of the hybrid system is detected, the message appears with the master warning tone when the “POWER” switch is on. If the message appears, stop the ve- hicle as soon as possible and contact a Toyota dealer.

light and warning

(b)

(d)

This message is to warn the driver that the engine oil pressure is too low. Turn the engine off as soon as possible and contact your Toyota dealer. The message appears with the master warning light and a warning tone sounds.

This message is to warn the driver that the engine coolant temperature is too high. Stop the vehicle and allow the engine to cool. See “If your vehicle overheats” on page 317 in Section 4. The message appears with the master warning light and a warning tone sounds.

NOTICE

Do not continue driving with an over- heated engine.

144

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(h)

(i)

(f)

This message is to remind the driver that any of the doors are opened. Close the door securely. The message appears with the master warning light and a warning tone sounds when the vehicle speed rises above 5
km/h (3 mph).

(g)

This message is to remind the driver that the trunk is opened. Close the trunk securely. the master The message appears with warning light a warning tone sounds when the vehicle speed rises above 5 km/h (3
mph).

This message is to warn the driver that the vehicle stability control (VSC) func- tion of the vehicle dynamics integrated management (VDIM) is malfunctioning. If the message appears, the functions of VDIM listed below may not work pro- perly. Have the vehicle checked by a Toyota dealer as soon as possible. However, as conventional braking oper- ates when applied, there is no problem to continue your driving. D Traction control function D Vehicle stability control function The message appears with the master warning light and a warning tone sounds. If the message appears together with the red brake system warning light, stop the vehicle immediately. For details, see “Ser- vice reminder indicators and warning buzz- ers” on page 150.

This message is to remind the driver that the transmission is not in the “P” position when starting the vehicle. If the message appears, put the trans- mission in the “P” position and push the “POWER” switch again. For the hy- brid system starting procedure, see “How to start the hybrid system” on page 301 in Section 3. The message appears with the master warning light and a warning tone sounds.

145

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(j)

(k)

(m)

in

the

following

This message is to warn of the hybrid battery condition. The message appears conditions.: D The hybrid battery voltage drops be- cause the transmission is left in the “N” position. If you put the transmission in the “P” position and the message disappears, the system is working properly.

This message is to warn the driver that the transmission is not in the “P” posi- tion when the driver’s door is opened. Put the transmission in the “P” posi- tion. The message appears with the master warning light and a warning tone sounds.

This message is to warn the driver that the transmission is not in the “P” posi- tion when leaving the vehicle. Put the transmission in the “P” posi- tion. The message appears with the master warning light and a warning tone sounds.

(l)

(n)

D The hybrid battery is discharged.

If the hybrid battery is discharged and the message appears along with the “READY” light turned on, stop your ve- hicle in a safe place and contact your Toyota dealer.

The message appears with the master warning light and a warning tone sounds.

This message is to remind the driver that the brake pedal is not depressed when starting the hybrid system. Depress the brake pedal firmly and press the “POWER” switch. For the starting pro- cedure, see “How to start the hybrid sys- tem” on page 301 in Section 3. If the brake pedal is not depressed, the message appears and a warning tone sounds when the hybrid system is started.

146

When this message appears in the fol- lowing cases, a warning tone sounds. D The key is not detected in the vehicle because someone has taken the key outside of the vehicle without turning the hybrid system off. At this time, a warning tone sounds. The above mes- sage turns off if the “POWER” switch is turned off or the key is in the ve- hicle.

D The key is not detected in the vehicle when the “POWER” switch is pushed. In this case, the above message ap- pears for 8 seconds.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(o)

(q)

(r)

This message is to warn the driver that the electronic key battery is low. Change the key battery as soon as pos- sible to ensure that the smart key sys- tem operates properly. The message appears with the master warning light and a warning tone sounds.

(p)

This message appears when the steer- ing lock is stuck. The message appears for 15 seconds. At this time, the green indicator light on the “POWER” switch flashes. To free the steering lock, rotate the steer- ing wheel slightly left or right while press- ing the “POWER” switch. the master The message appears with warning light and a warning tone sounds.

This message warns the driver that the steering lock function malfunctions. At this time, the amber indicator light on the “POWER” switch flashes. The hybrid system will not be turned on in this case. Contact your Toyota dealer as soon as possible. The message appears with the master warning light and a warning tone sounds.

This message is to remind the driver to change the engine oil. The message is a prior notice. Toyota recommends that the engine oil be changed as soon as possible. If the driving range after the previous oil change reaches 7200 km (4500 miles), the message appears for about 15 seconds with the master warning light and a warn- ing tone sounds. The engine oil maintenance data must be reset after the engine oil change. See following “Resetting the engine oil mainte- nance data”.

147

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(s)

This message is to remind the driver to change the engine oil. Change the engine oil as soon as pos- sible. If the driving range after the previous oil change reaches 8000 km (5000 miles), the message appears with the master warning tone sounds. The light and a warning message stays on with “POWER” switch set at ON. The engine oil maintenance data must be the engine oil change. See reset after “Resetting the engine oil maintenance data” below for the procedure to reset the system.

the

Resetting the engine oil maintenance data The engine oil maintenance data must be reset after replacement of the engine oil. Reset the data by the following procedure: 1. Turn off the hybrid system with the trip

meter A reading shown.

For details, see “—Odometer and two trip meters” on page 138 in this Section. 2. The “POWER” switch must be set at ON while holding down the trip meter reset knob. A message “OIL MILEAGE RESET MODE” will appear on the dis- play.

3. Hold down the knob at least 5 sec- onds. A message “COMPLETE” will ap- pear and the message “OIL MILEAGE RESET MODE” goes off.

(t)

This message appears when the washer fluid level becomes very low. Fill the tank as soon as possible. The message appears with warning light a warning tone sounds.

the master

(u)

is opened with

This message appears when the driver’s door the “POWER” switch turned off and the moon roof opened. When you leave your vehicle, be sure to close the moon roof. The message appears with the master warning light and a warning tone sounds.

148

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

(v)

This message is to remind the driver that the fuel filler door is open. The message appears cases. 1. When you start

the vehicle with the

following

the

in

fuel door left open after refueling.

2. When you leave the fuel door open for more than 30 minutes during refueling. In case 1, stop the vehicle and close the fuel lid. In case 2, the internal valve in the fuel tank is closed. You must remove the fuel nozzle, tighten the fuel tank cap and close the fuel door. If is not completed you must refueling start refueling from the beginning.

CAUTION

Do not continue to refuel in case 2. Fuel may spray out of the fuel open- ing if you refuel the vehicle.

the master The message appears with warning light and a warning tone sounds.

149

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Service reminder indicators and warning buzzers

If the indicator or buzzer comes on...

Do this.

or

(red indicator and buzzer)

(yellow indicator)

If parking brake is off, stop immediately and contact Toyota dealer.

Take vehicle to Toyota dealer. If red brake system warning light is also on, stop immediately and contact Toyota dealer.

(indicator and buzzer)

Fasten driver’s seat belt.

(indicator and buzzer)

Fasten front passenger’s seat belt.

Stop immediately and contact Toyota dealer.

or

Take vehicle to Toyota dealer.

Fill up tank.

(a)

(b)

(c)

(d)

(e)

(f)

150

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

If the indicator or buzzer comes on...

Do this.

(g)

(h)

(i)

(j)

(k)

(l)

or

Take vehicle to Toyota dealer. If red brake system warning light is also on, stop immediately and contact Toyota deal- er.

Take vehicle to Toyota dealer.

(indicator and buzzer)

Close all doors and trunk lid.

Take vehicle to Toyota dealer immediately.

Adjust tire inflation pressure (including spare tire). If the light comes on after blinking for 1 minute, contact Toyota dealer.

Read a message on multi−information display.

(m)

Parking brake reminder buzzer

Release parking brake.

151

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

in

the

lights come on

(a) Brake System Warning Lights These following cases when the hybrid system is turned on. RED WARNING LIGHT D When the parking brake is applied... When the vehicle speed exceeds 5 km/h (3 mph), a message “PARK BRAKE” ap- pears on the multi−information display, the master warning light flashes and a warn- ing tone sounds. D When the brake fluid level is low...

CAUTION

It is dangerous to continue driving normally when the brake fluid level is low.

YELLOW WARNING LIGHT D When the regenerative brake system or electronically controlled brake system fails...

When the yellow warning light comes on, the regenerative brake system and/or elec- tronically controlled brake system is mal- functioning. Take your vehicle to your Toyota dealer. RED AND YELLOW WARNING LIGHT D When fails...

the hydraulic brake system

If the red and yellow warning lights come on, it indicates a serious problem and you can continue driving no longer. Have your vehicle checked at your Toyota dealer in the following cases: D The red warning light does not come on even if the parking brake is applied when the hybrid system is on.

D The lights do not come on when the turned on with the

hybrid system parking brake released.

is

A red or yellow warning light turning on briefly during operation does not indicate a problem.

152

CAUTION

If any of the following conditions oc- curs, immediately stop your vehicle at a safe place and contact your Toyota dealer. D The red warning light does not turn off even after the parking brake is released with the hybrid system turned on.

D The red warning light stays on with

the hybrid system turned on.

In either case, this can indicate that the brakes may not work properly and your stopping distance will become longer. Depress the brake pedal firmly and bring the vehicle to an immediate stop. D The red brake system warning light remains on together with the “ABS” warning light and “CHECK VSC SYSTEM” warning message.

In this case, not only the anti−lock brake system and vehicle stability control system will fail but also the vehicle will become extremely unsta- ble during braking.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

In the following case, drive directly to the nearest Toyota dealer. D The yellow warning light comes on

while driving.

Any of the following conditions may oc- cur, but do not indicate the malfunc- tion: D The red and yellow warning lights may stay on for about 60 seconds after the hybrid system is started. It is normal if it turns off after a while.

D Depressing the brake pedal repeatedly may turn on the red and yellow warn- ing lights. It is normal if the light turns off after a few seconds.

D The brake pedal stroke may be short is depressed

the brake pedal

when with the hybrid system off.

’07Camry hybrid_U (L/O 0610)

(b) Driver’s Seat Belt Reminder Light

and Buzzer

(c) Front Passenger’s Seat Belt Re-

minder Light and Buzzer

The light and buzzer act as a reminder to buckle up the driver’s seat belt. Once the “POWER” switch is set at ON or engine start, the reminder light flashes and buzzer sounds if the driver’s seat belt is not fastened. Unless the driver fastens the belt, the light continues flashing and the buzzer sounds for about 6 seconds. If the vehicle speed rises above 20 km/h (12 mph) with the seat belt unfastened, the buzzer will sound for about 10 sec- onds. Then, if the seat belt is still unfas- tened, the buzzer will sound in a different tone for 20 seconds. Even if the vehicle speed drops below 20 km/h (12 mph), the buzzer will continue to sound. To stop the buzzer, fasten the seat belt. If the buzzer still sounds, make sure the front passen- ger’s seat belt is fastened. The vehicle speed linked seat belt remind- er buzzer can be disabled. For details, contact your Toyota dealer. However, Toyota the seat belt reminder buzzer be operational to alert the driver and front passenger that the seat belts are not fastened.

recommends

that

The light and buzzer act as a reminder to have the front passenger buckle up the seat belt. Once the “POWER” switch is set at ON, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. Unless the front passenger fastens the belt, the light con- tinue flashing. If the vehicle speed rises above 20 km/h (12 mph) with the seat belt unfastened, the buzzer will sound for about 10 sec- onds. Then, if the seat belt is still unfas- tened, the buzzer will sound in a different tone for 20 seconds. Even if the vehicle speed drops below 20 km/h (12 mph), the buzzer will continue to sound. To stop the buzzer, fasten the seat belt. If the buzzer still sounds, make sure the driver’s seat belt is fastened. If luggage or other load is placed on the its front passenger seat, depending on weight, flash and buzzer to sound. The vehicle speed linked seat belt remind- er buzzer can be disabled. For details, contact your Toyota dealer.

the reminder

light

to

153

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

If the lamp remains on, or the lamp comes on while driving, first check the followings. D Empty fuel tank

If the fuel tank is empty, refuel immedi- ately.

D Loose fuel tank cap

If the fuel tank cap is loose, securely tighten it.

These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips. If the lamp does not go off even after several trips, contact your Toyota dealer as soon as possible. If the fuel tank is not empty or the fuel tank cap is not loose... There is a problem somewhere in the hy- brid system, emission control system, electronic trans- mission electrical system or warning light system itself. Contact your Toyota dealer as soon as possible to service the vehicle.

throttle control system,

if

control

system

inspection

Emissions Inspection and Maintenance (I/M) programs Your vehicle may not pass a state emission the malfunction indicator lamp remains on. Contact your to check your vehicle’s Toyota dealer emission and OBD (On−Board Diagnostics) system before taking your vehicle for the inspection. For details, see “Emissions Inspection and Maintenance (I/M) programs” on page 345
in Section 6. (f) Low Fuel Level Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the low fuel level warning light may come on earlier than usual.

that

recommends

However, Toyota the seat belt reminder buzzer be operational to alert the driver and front passenger that the seat belts are not fastened. (d) Charging System Warning Light When there are problems in the charging system while the hybrid system is running, the warning light comes on.

NOTICE

is

When the charging system warning light comes on while the hybrid sys- running, malfunctions may tem have occurred. light comes on, immediately stop the ve- hicle in a safe place and contact your Toyota dealer.

If the warning

lamp

comes

(e) Malfunction Indicator Lamp This the “POWER” switch is set at ON and goes off when the “READY” light comes on. This means light system is operating properly.

the warning

on when

that

154

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

the

light goes off when

(g) “ABS” Warning Light This light comes on when the “POWER” switch is set at ON. If the anti−lock brake system function of the VDIM (vehicle dy- namics integrated management) is working properly, the “READY” light comes on. Thereafter, if the function malfunctions, the light comes on again. When the “ABS” warning light is on and the yellow brake system warning light is on, the anti−lock brake system function and the brake assist function of the VDIM may not operate so that the wheel could lock up during a sudden braking or brak- ing on slippery road surfaces However, the brake system still operates conven- tionally.

the

this

following conditions If any of occurs, indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the

“POWER” switch is set at ON.

D The

light

remains on when

the

“READY” light is on.

D The light comes on while you are driv-

ing.

A warning light turning on briefly during operation does not indicate a problem. If the light comes on together with the red brake system warning light, stop the ve- hicle immediately. For details, see “(a) Brake system warning light”.

Either of the following conditions may occur, but does not indicate the mal- function: D The light may stay on for about 60
seconds after is started. It is normal if the light goes off after a while.

the hybrid system

D Depressing the brake pedal repeatedly may turn on the light. It is normal if the light goes off after a few seconds.

CAUTION

If the “ABS” warning light remains on together with the red brake system warning light, stop your vehicle im- mediately in a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system function and brake as- sist function will fail but also the ve- hicle will become extremely unstable during braking.