2007 Toyota Camry HV Owners Manual

the

it

When inserting the filter in the filter outlet, keep the arrow pointing up.

NOTICE

To prevent damage to the air condi- tioning system, do the following. z When using

the air conditioning system, make sure that a filter is always installed. z When cleaning

filter, do not

the

clean the filter with water.

253

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 1− 10

OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Trip information Clock Compass Power outlets Garage door opener Portable ashtray Glove box Auxiliary boxes Rear console box Front cup holder Rear cup holder Grocery bag hooks Cargo net Floor mat

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

255
257
258
262
263
266
267
268
270
270
271
271
272
272

254

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Trip information (with navigation system)

’07Camry hybrid_U (L/O 0610)

CAUTION

Do not operate the screen while the vehicle is moving. Be sure to operate the screen only when the vehicle is stopped.

1. Push the “INFO” button to display

the “Information” screen.

2. Touch the “Trip information” on the

screen.

the

instrument panel

Trip information appears on the screen. When lights are turned on, the brightness of the screen will be reduced. You can adjust the screen. To adjust the brightness, see the “Navigation System Owner’s Manual” for the procedure.

the brightness of

255

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

information

listed above

The is dis- played when you touch the “Consump- tion” switch on the “Energy Monitor” screen. The displayed values on the screen indi- cate general driving conditions. Accuracy varies with driving habits and road condi- tions. When the “POWER” switch is set at ON, the last previously used mode displayed just before the “POWER” switch is turned off will appear. If “Reset All” is touched, all of the graph- ics and values except the cruising range will be reset. If the electrical power source is discon- nected from the navigation system screen, the screen will automatically be set to the initial mode. 1. Fuel consumption

the past 30

in

minutes (“Consumption”)

The transition of fuel consumption in the past 30 minutes is displayed in the graph.

Consumption screen

1. Transition of fuel consumption in the

past 30 minutes

2. Regenerated energy

in

the past 30

minutes

3. Best fuel economy among average 4. Cruising range 5. Average fuel consumption

256

2. Regenerated energy in the past 30

minutes

The regenerated energy in the past 30
minutes is indicated with symbols. One symbol indicates 50 Wh. Up to 4
symbols will be shown. The energy of 50
Wh illuminates a 50 W bulb for an hour. 3. Best fuel economy (lowest fuel con-

sumption) among average (“Best”)

Best fuel economy among average is displayed. If the average fuel consumption is reset by touching the “Reset” and the average fuel consumption is the lowest, the value is overwritten. 4. Cruising range

(“Cruising Range”)

fuel

The distance the vehicle can travel with the remaining is calculated and displayed based on the quantity of re- maining fuel and past fuel consumption. The cruising range display indicates the approximate distance that you can drive until is different from the actual distance traveled. If the fuel gauge malfunctions, the mileage figure will not appear.

fuel gauge reaches “E”.

the

It

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Clock

When the vehicle is refueled, the driving range is recalculated. The actual driving range varies with driv- ing habits and road conditions. If fuel con- sumption is good, the driving range will be longer than indicated. If fuel consumption is poor, the driving range will be shorter than indicated. If the low fuel level warning light comes on, refuel the vehicle even if the display indicates that the vehicle can be driven further. 5. Average fuel consumption

(“Average”)

Average fuel consumption is displayed based on total driving distance and to- tal fuel consumption. The calculation is reset by touching the “Reset”. If the average fuel consumption is the lowest, the value of the best fuel economy among average is overwritten.

Energy Monitor screen

the screen the energy. See

Touching the “Energy” switch turns on the “Energy Monitor” that displays the hybrid system operating condition. the The arrow on indicates movement of “Energy monitor” on page 3 for the representative screen. The segments of the screen indicate the status of the hybrid battery. See “—Hybrid battery status” on page 5 for details.

the battery on

To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. The “POWER” switch must be set at ACC or ON. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00 (one o’clock). When lights are turned on, the brightness of the time indi- cator will be reduced.

instrument panel

the

257

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Compass

D The vehicle is magnetized. (There is a magnet or a metal object on or near the inside rear view mirror.)

D The 12 volt battery has been discon-

nected.

the deviation

If your vehicle is out of the set zone, refer to “CALIBRATING THE COMPASS” below to set the zone number. If the compass works to calibrate the direction automati- cally while the vehicle is in motion. For additional precision or calibrating, see COMPASS” below.

for complete THE

“CALIBRATING

is small,

Displays

NE SE SW NW

Directions

North

Northeast

East

Southeast

South

Southwest

West

Northwest

The compass may not show the correct direction in the following conditions: D The vehicle is stopped immediately af-

ter turning.

D The compass does not adjust while the

vehicle is stopped.

D The “POWER” switch is turned off im-

mediately after turning.

D The vehicle is on an inclined surface. D The vehicle is in a place where the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

turn back on when

The direction is indicated on the inside rear view mirror. If the “POWER” switch was turned off with the system on, the system will automati- cally the “POWER” switch is turned on. Push the “AUTO” switch for longer than 3
seconds to turn the compass system on and off. the direction The compass that the above case, it shows that the vehicle is heading north.

is heading.

the vehicle

indicates

In

258

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

The compass sensor is in the inside rear view mirror.

NOTICE

Do not put magnets or a metal object on or near the inside rear view mirror of the vehicle. Doing this may cause malfunction of the compass sensor.

the

from

CALIBRATING THE COMPASS (deviation calibration) the compass The direction display on true direction deter- deviates mined by the earth’s magnetic field. The angle of deviation varies according to the geographic position of the vehicle. To adjust this deviation, stop the vehicle, then push and hold the switch until the zone number appears on the display. Then push the switch, referring to the fol- lowing map to select the number of the zone where the vehicle is.

259

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Samoa: 5

Guam:

Saipan: 8

After calibration, leaving the system for several seconds returns it to the compass mode.

CAUTION

Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

Zone numbers

260

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

the direction display on

CALIBRATING THE COMPASS (circling calibration) Sometimes the compass may not change after a turn. To rectify this, stop the vehicle and push and hold the switch until “C” appears on the display. If “C” appears on the display because of a drastic change in the magnetic field, perform circling calibration.

in a circle, drive around

Drive the vehicle in a circle at 8 km/h (5
mph) or less. If there is not enough space to drive the block. After driving 1 to 3 circles in the above method, calibration is completed when the direction is shown on the display. If calibration cannot be performed because of the magnetized vehicle etc., take your vehicle to Toyota dealer.

Perform circling calibration just after you have purchased your Toyota. And then always perform circling calibration after the 12 volt battery has been re- moved, replaced or disconnected. D Do not perform circling calibration of the compass the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

in a place where

D During calibration, do not operate elec- tric systems (moon roof, power win- dows, etc.) as they may interfere with the calibration.

261

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

CAUTION

D When doing the circling calibration, be sure to secure a wide space, and watch out for people and ve- hicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.

D Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

Power outlets

Front console

262

Center console

’07Camry hybrid_U (L/O 0610)

for

The power outlets are designed power supply for car accessories. The “POWER” switch must be set at ACC or ON for the power outlet to be used. Front console power outlet—Connected cables can be passed through the hole to the front passenger side of the auxiliary box. For details, see “Auxiliary boxes” on page 268 in this Section.

NOTICE

the

fuse

z To prevent

from being blown, do not use the electricity over the total vehicle capacity of 12V/120W.

z To prevent the 12 volt battery from being discharged, do not use the power outlets longer than necessary when the hybrid system is turned off.

z Close the power outlet

lids when the power outlets are not in use. Inserting anything other than an ap- propriate plug that fits the outlet, or allowing any liquid to get into the outlet may cause electrical fail- ure or short circuits.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Garage door opener

Buttons

Indicator light

The garage door opener ( Universal Transceiver) is manufactured under license from HomeLinkR and can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, and security systems, etc.

transmitter prior

(a) Programming the HomeLinkR The HomeLinkR in your vehicle has 3
buttons and you can store one program for each button. To ensure correct programming into the HomeLinkR, install a new battery in the hand−held to program- ming. The battery side of the hand−held trans- mitter must be pointed away the HomeLinkR during the programming pro- cess. For Canadian users, follow the procedure “Programming an entrance gate/pro- in gramming all devices the Canadian market”. 1. Decide which of 3 HomeLinkR buttons

from

in

you want to program.

HomeLinkr

25 to 75 mm (1 to 3 in.)

Hand−held garage transmitter

2. Place your hand−held garage transmit- ter 25 to 75 mm (1 to 3 in.) away from the surface of the HomeLinkR.

Keep the indicator light on the HomeLinkR in view while programming.

263

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

6. Repeat steps 2 through 5 for each re- maining HomeLinkR button to program another device.

3. Simultaneously press and hold

the hand−held garage transmitter button along with the selected HomeLinkR but- ton.

Do not release the buttons until step 4
has been completed. 4. When

the HomeLinkR changes from a slow to a rapid flash after 20 seconds, you can release both buttons.

light on

indicator

the

264

5. Test the operation of the HomeLinkR by pressing the newly programmed button. If programming a garage door opener, check to see if the garage door opens and closes.

If the garage door does not operate, iden- tify if your garage transmitter is of the “Rolling Code” type. Press and hold the programmed HomeLinkR button. The ga- rage door has the rolling code feature if the HomeLinkR) the flashes rapidly and then remains lit after 2 seconds. If your garage transmitter is the “Rolling Code” type, proceed to the heading “Programming a rolling code sys- tem”.

indicator

light

(on

it

is

to

is necessary

Programming a rolling code system “Rolling Code” If your device equipped, follow steps 1 through 4 under the heading “Programming the HomeLinkR” before proceeding with the steps listed below. 1. Locate the “training” button on the ceil- ing mounted garage door opener motor. The exact the button may vary by brand of garage door opener. Refer the owner’s guide supplied by the garage door opener manufacturer for the location of this “training” button.

location and color of

to

2. Press the “training” button on the ceil- ing mounted garage door opener motor. Following this step, you have 30 seconds in which to initiate step 3 below. 3. Press and release the vehicle’s pro- grammed HomeLinkR button twice. The garage door may open. the door does open, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door.

If

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

now

should

recognize

The ceiling mounted garage door opener motor the HomeLinkR unit and be able activate the garage door up/down. 4. Repeat steps 1 through 3 for each re- maining HomeLinkR button to program another rolling code system.

Programming an entrance gate/program- ming all devices in the Canadian market 1. Decide which of the 3 HomeLinkR but-

2. Place

your

tons you want to program. hand−held

gate/device transmitter 25 to 75 mm (1 to 3 in.) away the HomeLinkR.

surface

from

the

of

Keep the indicator light on the HomeLinkR in view while programming. 3. Press

selected

hold

and

the

HomeLinkR button.

4. Continuously press and release (cycle) transmitter the hand−held gate/device button every two seconds until step 5
is complete. the

the HomeLinkR changes from a slow to a rapid flash after 20 seconds, you can release both buttons.

light on

5. When

indicator

’07Camry hybrid_U (L/O 0610)

6. Test the operation of the HomeLinkR by pressing the newly programmed button. Check to see if the gate/device oper- ates correctly.

7. Repeat steps 1 through 6 for each re- maining HomeLinkR button to program another device.

Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. Reprogramming a button Individual HomeLinkR buttons cannot be erased, however, to reprogram a single button, follow the procedure “Programming the HomeLinkR”. (b) Operating the HomeLinkR To operate the appropriate HomeLinkR button to activate the programmed device. The HomeLinkR indicator light should come on. The HomeLinkR continues to send the signal for up the button is pressed.

the HomeLinkR, press

to 20 seconds as

long as

(c) Erasing

the

entire HomeLinkR

memory (all three programs)

To erase all previously programmed codes at one time, press and hold down the 2
outside buttons for 20 seconds until the indicator light flashes. If you sell your vehicle, be sure to erase the HomeLinkR the programs stored memory. For additional programming assistance Universal with Transceiver call the: D Toyota Customer Experience Center at

HomeLinkR

your

in

1−800−331−4331 (U.S.A.)

D Toyota Canada Customer

Interaction

Centre at 1−888−869−6828 (Canada)

265

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Portable ashtray

received,

This device complies with Part 15 of the FCC Rules and with RSS−210 of the IC Rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer- ence interference that may cause undesired operation. WARNING: This transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party re- sponsible for compliance could void the user’s authority to operate the device.

including

Refer to HomeLinkR on the internet at: WWW.HOMELINK.COM

CAUTION

D When programming the HomeLinkR Universal Transceiver, you may be operating a garage door or other device. Make sure people and ob- jects are out of the way of the ga- rage door or other device to pre- vent potential harm or damage.

D Do not use this HomeLinkR Univer- sal Transceiver with any garage door opener that lacks the safety stop and reverse feature as re- quired by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982.) A garage door open- er which cannot detect an object (signaling the door to stop and re- verse), does not meet current feder- al safety standards. Using a garage door opener without these features increases risk of serious injury or death.

266

The ashtray can be removed and used outside the vehicle. To use the ashtray, raise the lid. finished with your cigarette, thor- When oughly extinguish it in the ashtray to pre- vent other cigarette butts from catching fire. After using the ashtray, close the lid completely. The cup holder lid cannot be closed while the ashtray is installed. To detach the ashtray, pull it out.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Glove box

CAUTION

To reduce the chance of in case of an accident or sudden stop while driving, always completely close the ashtray after use.

injury

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.

injury

To use the glove box: Open by pulling the lever. Lock by inserting the mechanical key and turning it clockwise. Unlock by and turning it counterclockwise. With the instrument panel lights on, the glove box light will come on when the glove box is open.

inserting the mechanical key

267

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Auxiliary boxes

268

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

To use the boxes, open it as shown the illustration. 1. Driver’s side instrument panel 2. Overhead console 3. Front console

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the auxiliary box closed while driving.

injury

NOTICE

Overhead console box—During hot weather, the interior of the vehicle becomes very hot. Do not leave any- thing flammable or deformable such as a lighter, glasses, etc. inside.

’07Camry hybrid_U (L/O 0610)

CABLE PASS−THROUGH The auxiliary box of the front console is provided with a hole that allows cables to be passed into the cabin from the inside power outlet and AUX adapter. To open the hole, perform the following procedure: 1. Remove the lid on the inside of the

auxiliary box.

2. From the inside of the auxiliary box,

push out and remove the outer lid.

Be careful not to lose the removed lids.

269

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Rear console box

Front cup holder

To open the console box, push the lock release button and raise the console box lid. The upper tray slides forward/backward and can be removed.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the console box closed while driving.

injury

The cup holder is designed for holding cups or drink−cans securely. To use them, open it as shown in the illustra- tion. The adapter for front cup holder is detach- able. Replace its original position when using the front cup holder. Other- wise the drinks will not be held securely.

in

it

270

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

CAUTION

D Do not place anything else other than cups or drink−cans in the cup items may be holder, as such thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.

D To reduce the chance of injury in case of an accident or sudden stop while driving, keep the cup holder closed when it is not in use.

’07Camry hybrid_U (L/O 0610)

Rear cup holder

Grocery bag hooks

This hook is designed to hang things like grocery bags.

NOTICE

To prevent damage to the hook, avoid hanging heavy loads on it.

The cup holder is designed for holding cups or drink−cans securely. To use it, pull down the armrest.

CAUTION

D Do not place anything else other than cups or drink−cans in the cup holder, as such items may be thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.

D Do not lift the armrest upright when

the cup holder is in use.

271

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Cargo net

Floor mat

Use a floor mat of the correct size. If the vehicle carpet and floor mat have two holes, then they are designed for use with locking clips. Attach the floor mat to the vehicle carpet using the clips. Lock the clips the vehicle carpet.

the holes

into

in

To secure belongings, hang the cargo net on the hooks.

NOTICE

z Do not use the net to secure sharp or heavy objects. The net will tear off.

z Be sure not to twist the net when

hooking.

272

CAUTION

Make sure the floor mat is properly placed on the vehicle carpet. If the floor mat slips and interferes with the movement of the pedals during driv- ing, it may cause an accident.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

273

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 2

INFORMATION BEFORE DRIVING YOUR TOYOTA Information before driving your Toyota Break−in period Fuel Operation in foreign countries Three−way catalytic converters Engine exhaust cautions Facts about engine oil consumption Iridium−tipped spark plugs Brake system Electric power steering system Brake pad wear limit indicators Your Toyota’s identification Theft prevention labels Suspension and chassis Tire information Vehicle load limits Cargo and luggage Types of tires

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

275
275
277
277
278
279
280
281
282
282
283
284
284
285
295
295
298

274

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Break−in period Drive gently and avoid high speeds. Your vehicle does not need an elaborate break−in. But following a few simple tips for the first 1600 km (1000 miles) can add to the future economy and long life of your vehicle: D Avoid full

throttle acceleration when

starting and driving.

D Avoid racing the hybrid system. D Try to avoid hard stops during the first

300 km (200 miles).

D Do not drive for a long time at any

single speed, either fast or slow.

D Do not tow a trailer during the first 800

km (500 miles).

Fuel FUEL TYPE Your new vehicle must use only un- leaded gasoline. To help prevent gas station mix−ups, your Toyota has a smaller fuel tank opening. The special nozzle on pumps with un- leaded fuel will fit it, but the larger stan- dard nozzle on pumps with leaded gas will not. At a minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB 3.5−M93
in Canada.

NOTICE

Do not use leaded gasoline. Use of leaded gasoline will cause the three− way catalytic converter to lose its ef- fectiveness and the emission control system to function improperly. Also, this can increase maintenance costs.

OCTANE RATING Select Octane Rating 87 (Research Oc- tane Number 91) or higher. Use of unleaded gasoline with an octane rating lower than 87 may result in engine knocking. Persistent knocking can lead to engine damage. If your engine knocks... If you detect heavy knocking even when using if you hear steady knocking while holding a steady speed on level roads, consult your Toyota dealer. However, occasionally, you may notice light knocking for a short time while accel- erating or driving up hills. This is normal and there is no need for concern.

the recommended

fuel, or

275

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

CLEANER BURNING GASOLINE Cleaner burning gasoline, including re- formulated gasoline that contains oxy- genates such as ethanol or MTBE is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gas- oline provide excellent vehicle perfor- mance, reduce vehicle emissions, and im- prove air quality. OXYGENATES IN GASOLINE Toyota allows the use of oxygenate blended gasoline where the oxygenate content is up to 10% ethanol or 15% MTBE. in your Toyota, be sure that it has an octane rating no lower than 87. Toyota does not recommend the use of gasoline containing methanol.

If you use gasohol

GASOLINE CONTAINING MMT Some gasoline contain an octane en- hancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel con- taining MMT is used, your emission con- trol system may be adversely affected. The Malfunction Indicator Lamp on the in- strument cluster may come on. If this hap- pens, contact your Toyota dealer for ser- vice. GASOLINE QUALITY In a very few cases, you may experience driveability problems caused by the partic- ular gasoline that you are using. If you continue to have unacceptable driveability, try changing gasoline brands. If this does not rectify your problem, then consult your Toyota dealer.

in

GASOLINE CONTAINING DETERGENT ADDITIVES Toyota recommends the use of gasoline that contains detergent additives to avoid build−up of engine deposits. However, all gasoline sold the U.S. contains detergent additives to keep clean and/or clean intake systems. QUALITY GASOLINE Automotive manufacturers in the U.S., Europe and Japan have developed a specification fuel named World−Wide Fuel Charter (WWFC) that is expected to be applied world wide. The WWFC consists of four categories that depend on required emisvels. In the U.S., category 4 has been adopted. The WWFC improves air quality by pro- viding for better emissions in vehicle fleets, satisfaction through better vehicle performance.

for quality

customer

and

276

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

NOTICE

z Do not use gasohol other

than stated above. It will cause fuel sys- tem damage or vehicle performance problems.

z If driveability problems are encoun- tered (poor hot starting, vaporizing, engine knock, etc.), discontinue the use.

z Take care not to spill gasohol dur- ing refueling. Gasohol may cause paint damage.

FUEL TANK CAPACITY

65 L (17.2 gal., 14.3 Imp. gal.)

’07Camry hybrid_U (L/O 0610)

Three−way catalytic converters

Operation in foreign countries If you plan to drive your Toyota another country... First, comply with the vehicle registration laws. Second, confirm the availability of the cor- rect fuel (unleaded and minimum octane number).

in

The three−way catalytic converter is an emission control device installed in the exhaust system. The purpose is to reduce pollutants in the exhaust gas.

CAUTION

D Keep people and combustible mate- rials away from the exhaust pipe while the engine is running. The exhaust gas is very hot.

D Do not drive, idle or park your ve- hicle over anything that may burn easily such as grass, leaves, paper or rags.

277

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

NOTICE

large amount of unburned gases into the three−way catalytic flowing converter may cause it to overheat and create a fire hazard. To prevent this and other damage, observe the following precautions: z Use only unleaded gasoline. z Do not drive with an extremely low fuel level; running out of fuel could cause the engine to misfire, creat- ing an excessive load on the three− way catalytic converter.

z Do not turn the “POWER” switch

off while the vehicle is moving.

in

z Keep your engine in good running order. Malfunctions the engine electrical system, electronic ignition system/distributor ignition system or fuel system could cause an ex- tremely high three−way catalytic converter temperature.

z If the engine becomes difficult to start or stalls frequently, take your vehicle in for a check−up as soon as possible. Remember, your Toyota dealer knows your vehicle and its three−way catalytic converter sys- tem best.

z To ensure that the three−way cata- lytic converter and the entire emis- sion control system operate proper- ly, your vehicle must receive the periodic inspections required by the Toyota Maintenance Schedule. For scheduled maintenance information, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supple- ment”.

z Do not apply a coating agent such as an anti−rust under−coating to the exhaust pipe.

278

Engine exhaust cautions

CAUTION

D Avoid inhaling the engine exhaust. It contains carbon monoxide, which is a colorless and odorless gas. It can cause unconsciousness or even death.

D Make sure the exhaust system has no holes or loose connections. The system should be checked from time to time. If you hit something, or notice a change in the sound of the the system exhaust, have checked immediately.

D Do not run the hybrid system in a garage or enclosed area except for the time needed to drive the vehicle in or out. The exhaust gases cannot escape, making this a particularly dangerous situation.

D Do not remain for a long time in a parked vehicle with the hybrid sys- tem operating. If it is unavoidable, however, do so only in an uncon- fined area and adjust the heating or cooling system to force outside air into the vehicle.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

D Keep

the

trunk

lid closed while driving. An open or unsealed trunk lid may cause exhaust gases to be drawn into the vehicle.

D To allow proper operation of your vehicle’s ventilation system, keep the inlet grilles in front of the wind- shield clear of snow, leaves, or oth- er obstructions.

D If you smell exhaust fumes in the vehicle, open the windows and close the trunk lid to ensure plenty of fresh air enters the vehicle. If you can smell exhaust fumes even though there are no other vehicles in the surrounding area, have your vehicle checked by your Toyota dealer. Continued inhalation of ex- haust fumes can lead to death by gas poisoning.

’07Camry hybrid_U (L/O 0610)

Facts about engine oil consumption FUNCTIONS OF ENGINE OIL Engine oil has the primary functions of lubricating and cooling the inside of the engine, and plays a major role in main- taining the engine in proper working order. ENGINE OIL CONSUMPTION It is normal that an engine should con- sume some engine oil during normal engine operation. The causes of oil consumption in a normal engine are as follows. D Oil is used to lubricate pistons, piston rings and cylinders. A thin film of oil is left on the cylinder wall when a pis- ton moves downwards in the cylinder. High negative pressure generated when the vehicle is decelerating sucks some of this oil into the combustion chamber. This oil as well as some part of the oil film left on the cylinder wall is burned by temperature combustion gases during the combustion process.

the high

D Oil is also used to lubricate the stems of the intake valves. Some of this oil is sucked into the combustion chamber together with is burned along with the fuel. High tem- perature exhaust gases also burn the oil used to lubricate the exhaust valve stems.

intake air and

the

The amount of engine oil consumed de- pends on the viscosity of the oil, the quality of the oil and the conditions the vehicle is driven under. More oil is consumed by high−speed driv- ing and frequent acceleration and decel- eration. A new engine consumes more oil, since its pistons, piston rings and cylinder walls have not become conditioned. Oil consumption: Max. 1.0 L per 1000
km (1.1 qt./600 miles, 0.9 lmp. qt./600
miles)

279

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Iridium−tipped spark plugs

When judging the amount of oil con- sumption, note that the oil may become diluted and make it difficult to judge the true level accurately. As an example, if a vehicle is used for repeated short trips, and consumes a nor- mal amount of oil, the dipstick may not show any drop in the oil level at all, even after 1000 km (600 miles) or more. This is because the oil is gradually becoming diluted with fuel or moisture, making it appear that the oil level has not changed. The diluting ingredients evaporate out when the vehicle is then driven at high speeds, as on an express way, making it appear that oil is excessively consumed after driving at high speeds.

IMPORTANCE OF ENGINE OIL LEVEL CHECK One of the most important points in prop- er vehicle maintenance is to keep the en- gine oil at the optimum level so that oil function will not be impaired. Therefore, it is essential that the oil level be checked regularly. Toyota recommends that the oil level be checked every time you refuel the vehicle.

NOTICE

Failure to check the oil level regularly could lead to serious engine trouble due to insufficient oil.

For detailed information on oil level check, see “Checking level” on page 355 in Section 7−2.

the engine oil

280

Your engine is fitted with iridium−tipped spark plugs.

NOTICE

Use only iridium−tipped spark plugs. Do not adjust gaps for engine perfor- mance or smooth driveability.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Brake system REGENERATIVE BRAKE When the brake is applied, the motor gen- erator converts kinetic energy into electric energy. When applying brakes, you may hear a sound coming from the motor generator. However, indicate any trouble. The regenerative brake works in the fol- lowing operations. 1. When the accelerator pedal is released, to engine the braking in a gasoline−fueled vehicle is obtained in accordance with the running mode position of the selector lever.

reduced speed equal

this does not

2. When

the brake pedal

is depressed with the selector lever in “D” or “B”, the regenerative brake works.

HYDRAULIC BRAKE This brake system has 3 independent hy- draulic circuits. If any circuit should fail, the other will still work. However, the ped- al will be harder to press, and your stop- ping distance will the brake system warning light may come on.

increase. Also,

CAUTION

Do not drive your vehicle if any hy- draulic circuit has failed. Have your brakes fixed immediately.

the brake pedal

the brake system warning

BRAKE ACTUATOR The brake actuator uses brake fluid pres- surized by the pump to power−assist the brakes. If the brake actuator fails during driving, light comes on and the buzzer sounds continu- ously. In this case, the brakes may not work properly. If they do not work well, depress the brake system warning light comes on, im- mediately stop your vehicle and contact your Toyota dealer. The red and yellow brake system warning lights may stay on for about 60 seconds after the hybrid system is turned on. It is normal if the light turns off after a while. Depressing repeatedly may turn on the red warning light and buzzer. It is normal if the light turns off after a few seconds.

the brake pedal

firmly.

If

In the following conditions, you may hear a sound in the engine compartment. This is not a malfunction. D The driver’s door is opened with the

hybrid system turned off.

D The brake pedal is depressed with the

hybrid system turned off.

D After the hybrid system is turned on. D The brake pedal is depressed repeated-

ly with the hybrid system turned on. D After the hybrid system is turned off. The brake pedal may be hard to depress or the brake pedal stroke may be short before turning the hybrid system on. This is not a malfunction.

281

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

CAUTION

D Even if the power assist

D Do not pump the brake pedal if the hybrid system is not operating. Each push on the pedal uses up your reserved brake fluid pressure. is com- pletely the brakes will still work. But you will have to push the pedal hard, much harder than nor- mal. And your braking distance will increase.

lost,

DRUM−IN−DISC TYPE PARKING BRAKE SYSTEM Your vehicle has a drum−in−disc type parking brake system. This type of brake system needs bedding−down of the brake shoes periodically or whenever the parking brake shoes and/or drums are replaced. Have your Toyota dealer perform the bed- ding−down.

282

Brake pad wear limit indicators

turned

Electric power steering system Driving conditions where the steering wheel must be frequently may cause an overload to the electric power steering system. The system will reduce assistance the power steering from overheating. In this case, you may feel some resistance when turning the steering wheel though it is not a malfunction.

for sometime

to prevent

CAUTION

If the “P/S” warning light comes on, take your vehicle to the Toyota dealer as soon as possible. In this case, you may feel the heavy steering wheel maneuvering. Drive your vehicle while gripping the steering wheel firmly.

The brake pad wear limit indicators on your disc brakes give a warning noise when the brake pads are worn to where replacement is required. If you hear a squealing or scraping noise while driving, have the brake pads checked and replaced by your Toyota dealer as soon as possible. Expensive ro- tor damage can result if the pads are not replaced when necessary.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Your Toyota’s identification— —Vehicle identification number

—Engine and traction motor numbers

The vehicle identification number (VIN) is the legal identifier for your vehicle. This number is on the left top of the instrument panel, and can be seen through the windshield from outside. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle.

The vehicle identification number (VIN) is also on the Certification Label.

1. Engine number 2. Traction motor number

The engine and traction motor numbers are stamped as shown.

283

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Suspension and chassis

CAUTION

Do not modify the suspension/chassis with lift kits, spacers, springs, etc. It can cause dangerous vehicle handling characteristics, resulting loss of control.

in

Theft prevention labels Your new vehicle carries theft preven- tion labels which are approximately 47
mm (1.85 in.) by 12 mm (0.47 in.). The purpose of these labels is to reduce the incidence of vehicle thefts by facilitat- ing the tracing and recovery of parts from stolen vehicles. The label is designed so that once it is applied to a surface, any attempt to remove it will result in destroy- ing the integrity of the label. Transferring these labels intact from one part to anoth- er, will be impossible.

NOTICE

You should not attempt to remove the theft prevention labels as it may vio- late certain state or federal laws.

284

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Tire information— —Tire symbols (standard tire)

’07Camry hybrid_U (L/O 0610)

This illustration indicates typical tire symbols. 1. Tire size—For details, see “—Tire

size” on page 289.

2. DOT and Tire

Identification Number (TIN)—For details, see “—DOT and Tire Identification Number (TIN)” on page 288.

tire

quality

3. Uniform

gra- ding—For details, see “Uniform Tire Quality Grading” that follows. 4. The location of the tread wear indicators—For see “Checking and replacing tires” on page 362.

details,

5. Tire ply composition and mate- rials—Plies mean a layer of rub- ber−coated parallel cords. Cords mean the strands forming the plies in the tire.

6. Radial tires or bias−ply tires—A radial tire has “RADIAL” on the sidewall. A tire not marked with “RADIAL” is a bias−ply tire.

285

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

7. “TUBELESS”

or

“TUBE TYPE”—A tubeless tire does not have a tube inside the tire and air is directly filled in the tire. A tube type tire has a tube inside the tire and the tube maintains the air pressure.

8. Load limit at maximum cold tire inflation pressure—For details, see “Checking and replacing tires” on page 362.

9. Maximum cold

tire

tire

cold

inflation pressure—This means the pres- sure to which a tire may be in- flated. For details about recom- mended inflation pressure, see “Tires” on page 385. tire or all season tire—An all season tire has “M+S” on tire not marked with “M+S” is a summer tire. For details, see “Types of tires” on page 298.

the sidewall. The

10.Summer

286

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

—Tire symbols (compact spare tire)

This illustration indicates typical tire symbols. 1. “TEMPORARY USE ONLY”—A compact spare tire is identified by the phrase “TEMPORARY USE ONLY” molded into its sidewall. This tire is designed for temporary emergency use only. For details, see “Compact spare tire” on page 319.

2. Tire size—For details, see “—Tire

size” on page 289.

3. DOT and Tire

Identification Number (TIN)—For details, see “—DOT and Tire Identification Number (TIN)” on page 288.

4. The location of the tread wear indicators—For see “Checking and replacing tires” on page 362.

details,

5. Load limit at maximum cold tire inflation pressure—For details, see “Checking and replacing tires” on page 362.

287

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

tire

cold

6. Maximum cold

inflation pressure—This means the pres- sure to which a tire may be in- flated. For details about recom- mended inflation pressure, see “Tires” on page 385. 7. Tire ply composition and mate- rials—Plies mean a layer of rub- ber−coated parallel cords. Cords mean the strands forming the plies in the tire.

tire

8. “TUBELESS”

or

“TUBE TYPE”—A tubeless tire does not have a tube inside the tire and air is directly filled in the tire. A tube type tire has a tube inside the tire and the tube maintains the air pressure.

9. Radial tires or bias−ply tires—A radial tire has “RADIAL” on the sidewall. A tire not marked with “RADIAL” is a bias−ply tire.

288

’07Camry hybrid_U (L/O 0610)

—DOT and Tire Identification Number (TIN)

The “DOT” symbol certifies that the tire conforms to applicable Federal Motor Vehicle Safety Standards.

This illustration indicates typical DOT and Tire Identification Number (TIN). 1. “DOT” symbol 2. Tire Identification Number (TIN) 3. Tire manufacturer’s identification

mark

4. Tire size code 5. Manufacturer’s optional tire type

code (3 or 4 letters) 6. Manufacturing week 7. Manufacturing year

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

—Tire size

—Name of each section of tire

This illustration indicates typical tire size. 1. Tire use

(P=Passenger car,

T=Temporary use)

2. Section width (in millimeters) 3. Aspect ratio (tire height to section

width)

4. Tire construction code (R=Radial,

D=Diagonal)

5. Wheel diameter (in inches) 6. Load index (2 digits or 3 digits) 7. Speed symbol (alphabet with one

letter)

1. Section width 2. Tire height 3. Wheel diameter

1. Bead 2. Sidewall 3. Shoulder 4. Tread 5. Belt 6. Inner liner 7. Reinforcing rubber 8. Carcass 9. Rim lines 10.Bead wires 11. Chafer

289

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

—Uniform Tire Quality Grading This information has been prepared in accordance with regulations issued by the National Highway Traffic Safe- ty Administration of the U.S. Depart- ment of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with in- formation on uniform tire quality grad- ing. Your Toyota dealer will help answer any questions you may have as you read this information. DOT quality grades—All passenger vehicle tires must conform to Fed- eral Safety Requirements in addi- tion these grades. Quality grades can be found where appli- cable on the tire sidewall between tread shoulder and maximum sec- tion width. For example: Treadwear 200 Traction AA Temperature A

to

290

’07Camry hybrid_U (L/O 0610)

Treadwear—The treadwear grade is a comparative rating based on the wear rate of the tire when tested un- der controlled conditions on a speci- fied government test course. For ex- ample, a tire graded 150 would wear one and a half (1−1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving hab- its, service practices and differences in road characteristics and climate.

Traction AA, A, B, C—The traction grades, from highest to lowest, are AA, A, B, and C, and they represent the tire’s ability to stop on wet pave- ment as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor trac- tion performance. Warning: The traction grade assigned to tire is based on braking (straight ahead) traction tests and does not include cornering (turning) traction.

this

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Temperature A, B, C—The tempera- ture grades are A (the highest), B, and C, representing the tire’s resis- tance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C cor- responds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No.109. Grades B and A represent higher levels of per- formance on the laboratory test wheel than the minimum required by law. Warning: The temperature grades for this tire are established for a tire that is properly inflated and not over- loaded. Excessive speed, underinfla- tion, or excessive loading, either sep- arately or in combination, can cause heat buildup and possible tire failure.

’07Camry hybrid_U (L/O 0610)

291

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

—Glossary of tire terminology

Tire related term

Accessory weight

Cold tire inflation pressure

Curb weight

Intended outboard sidewall

Maximum inflation pressure

Meaning

the combined weight (in excess of those standard items which may be replaced) of transaxle, power steering, power brakes, power windows, power seats, radio, and heater, to the extent that these items are available as factory−installed equipment (whether installed or not) tire inflation pressure when the vehicle has been parked for at least 3
hours or more, or it has not been driven more than 1.5 km or 1 mile under that condition the weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil, and coolant, and, if so equipped, air conditioning and additional weight optional engine (A) the sidewall that contains a whitewall, bears white lettering or bears

manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or

(B) the outward facing sidewall of an asymmetrical tire that has a particular

side that must always face outward when mounted on a vehicle

the maximum cold inflation pressure to which a tire may be inflated and it is shown on the sidewall of the tire

Maximum loaded vehicle weight

the sum of— (a) curb weight; (b) accessory weight; (c) vehicle capacity weight; and (d) production options weight

292

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Tire related term

Normal occupant weight

Occupant distribution

Production options weight

Recommended inflation pressure

Rim

Rim diameter (Wheel diameter) Rim size designation Rim type designation Rim width Vehicle capacity weight (Total load capacity)

Vehicle maximum load on the tire