2007 Toyota Camry HV Owners Manual

327

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. In consultation with them, have your vehicle towed using either (a) or (b). Proper equipment will help ensure that your vehicle is not damaged while being towed. Commercial operators are generally aware of local laws pertaining to towing. Your vehicle can be damaged is towed incorrectly. Although most operators know the correct procedure, it is possible to make a mistake. To avoid damage to your vehicle, make sure the following pre- cautions are observed. If necessary, show this page to the tow truck driver.

the state/provincial and

if

it

CAUTION

If your vehicle needs to be towed, do it with the front wheels raised. If the wheels with the motor generator are on the ground when towing, the mo- tor may continue to generate electrici- ty. This may cause the electricity lea- kage. Depending on the severity of the damage, electricity leakage may cause fire.

328

’07Camry hybrid_U (L/O 0610)

TOWING PRECAUTIONS: Use a safety chain system for all towing, and abide by the state/provincial and local laws. The wheels and axle on the ground must be in good condition. If they are damaged, use a towing dolly. (a) Towing with wheel lift type truck

NOTICE

When lifting wheels, take care to en- sure adequate ground clearance for towing at the opposite end of the raised vehicle. Otherwise, the bumper and/or underbody of the towed vehicle will be damaged during towing.

(c) Towing with sling

type truck

(c) Towing with sling type truck

NOTICE

From front—Release the parking brake. From rear— Use a towing dolly under the front wheels.

Do not tow with sling type truck, ei- ther from the front or rear. This may cause body damage.

NOTICE

Never tow a vehicle from the rear with the front wheels on the ground, as this may cause serious damage to the transmission.

(b) Using flat bed truck

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

If you cannot shift transmission selector lever

though

the brake pedal

If you cannot shift the selector lever out of “P” position to other positions even is de- pressed, use the shift lock override but- ton as follows: 1. Make sure

is turned off and the parking brake is on. Insert the flathead screwdriver or equivalent to the slot of the cover and pry it up.

the hybrid system

2. Press the “POWER” switch and start the hybrid system. For your safety, keep the brake pedal depressed.

3. With pushing down the shift

lock override button, shift out of the “P” position while depressing the brake pedal.

As the hybrid system starts only with the transmission in the “P” position, put the selector lever in “P” whenever starting the system. Be sure to have the system checked by your Toyota dealer as soon as possible.

329

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

the suggestion given in “Keys” on

If you lose your keys You can purchase a new electronic key at your Toyota dealer if you can give them the key number and master key. If you lose any of your keys, contact your Toyota dealer to have new keys made. Lost keys increase the danger of vehicle theft. Bring all of the remaining vehicle keys when you visit your Toyota dealer. See page 22 in Section 1−2. You can use the wireless remote control function and smart entry and start function by new key. Contact your Toyota dealer for detailed information. If your keys are locked in the vehicle and you cannot get a duplicate, many Toyota dealers can still open the door for you, If you must using break a window in, we suggest breaking the smallest side window be- cause it is the least expensive to replace. Be extremely cautious to avoid cuts from the glass.

their special

to get

tools.

330

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

331

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 5

CORROSION PREVENTION AND APPEARANCE CARE Corrosion prevention and appearance care Protecting your Toyota from corrosion Washing and waxing your Toyota Cleaning the interior

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

333
334
336

332

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Protecting your Toyota from corrosion Toyota, through the diligent research, de- sign and use of the most advanced technology available, helps prevent corro- sion and provides you with the finest qual- ity vehicle construction. Now, it is up to you. Proper care of your Toyota can help ensure long−term corrosion prevention. The most common causes of corrosion to your vehicle are: D The accumulation of road salt, dirt and moisture in hard−to−reach areas under the vehicle.

D Chipping of paint, or undercoating caused by minor accidents or by stones and gravel.

Care is especially important if you live in particular areas or operate your ve- hicle under certain environmental condi- tions: D Road salt or dust control chemicals will accelerate corrosion, as will the pres- ence of salt in the air near the sea− coast or in areas of industrial pollution. D High humidity accelerates corrosion es- pecially when temperatures range just above the freezing point.

D Wetness or dampness to certain parts of your vehicle for an extended period of time, may cause corrosion even though other parts of the vehicle may be dry.

D High ambient temperatures can cause corrosion to those components of the vehicle which do not dry quickly due to lack of proper ventilation.

The above signifies the necessity to keep your vehicle, particularly the underside, as clean as possible and to repair any dam- age to paint or protective coatings as soon as possible. To help prevent corrosion on your Toyota, follow these guidelines: Wash your vehicle frequently. It is, of course, necessary to keep your vehicle clean by regular washing, but to prevent corrosion, the following points should be observed: D If you drive on salted roads

the winter or if you live near the ocean, you should hose off the undercarriage at least once a month to minimize cor- rosion.

in

D High pressure water or steam is effec- tive for cleaning the vehicle’s underside and wheel housings. Pay particular attention to these areas as it is difficult to see all the mud and dirt. It will do more harm than good to simply wet the mud and debris without removing. The lower edge of doors, rocker panels and frame members have drain holes which should not be allowed to clog with dirt as trapped water in these areas can cause corrosion.

D Wash the underside of the vehicle thor-

oughly when winter is over.

See “Washing and waxing your Toyota” on page 334 for more tips. Check the condition of your vehicle’s paint and trim. If you find any chips or scratches in the paint, touch them up im- mediately to prevent corrosion from start- ing. If the chips or scratches have gone through the bare metal, have a qualified body shop make the repair.

333

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Check the interior of your vehicle. Wa- ter and dirt can accumulate under the floor mats and could cause corrosion. Oc- casionally check under the mats to make sure the area is dry. Be particularly care- ful when transporting chemicals, cleans- ers, fertilizers, salt, etc.; these should be transported in proper containers. If a spill or leak should occur, immediately clean and dry the area. Use mud shields on your wheels. If you drive on salted or gravel roads, mud shields help protect your vehicle. Full−size shields, which come as near to the ground as possible, are the best. We recommend that the fittings and the area where the shields are installed be treated to resist corrosion. Your Toyota dealer will be happy to assist in supplying and installing the shields if they are recommended for your area. Keep your vehicle in a well ventilated garage or a roofed place. Do not park your vehicle in a damp, poorly venti- lated garage. If you wash your vehicle in the garage, or if you drive it covered with water or snow, your garage may be so damp as to cause corrosion. Even if your garage is heated, a wet vehicle can cor- rode if the ventilation is poor.

334

’07Camry hybrid_U (L/O 0610)

Washing and waxing your Toyota Your Toyota is a hybrid vehicle. Pay particular attention when washing your Toyota.

NOTICE

Before washing your Toyota, be sure to observe the following in order to avoid the risk of damage to your ve- hicle. Do not splash water on the electric components in the engine compart- ment. This may cause malfunction of the electric components.

Washing your Toyota Keep your vehicle clean by regular washing. The following cases may cause weakness to the paint or corrosion to the body and parts. Wash your vehicle as soon as pos- sible. D When driving in a coastal area D When driving on a road sprinkled with

antifreeze

D When exposed to coal tar, tree sap, bird droppings and carcass of an insect

D When driving in areas where there is a lot of smoke, soot, dust, iron dust or chemical substances

D When the vehicle becomes remarkably

dirty with dust and mud Hand−washing your Toyota Work in the shade and wait until the vehicle body is not warm to the touch.

CAUTION

D When cleaning under floor or chas- sis, be careful not to injure your hands.

D Exhaust gases cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot ex- haust pipe can cause burns.

1. Rinse off loose dirt with a hose. Re- move any mud or road salt from the underside of the vehicle or the wheel wells.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

tar: Remove with

Road turpentine or cleaners that are marked safe for painted surfaces. 3. Rinse

can cause streaking. In hot weather you may need to rinse each section right after you wash it.

thoroughly—dried

soap

4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not rub or press hard—you might scratch the paint.

NOTICE

z Do not use organic substances (gasoline, kerosene, benzine or strong solvents), which may be tox- ic or cause damage.

z Do not scrub any part of the ve- hicle with a hard brush, which may cause damage.

2. Wash with a mild car−wash soap, mixed according to the manufacturer’s instructions. Use a soft cotton mitt and keep it wet by dipping it frequently into the wash water. Do not rub hard—let the soap and water remove the dirt.

Fuel filler door: Do not apply water (high− pressure car wash, for example) at or near the fuel tank inlet with the fuel filler door opened. If the water enters the air vent, you may experience trouble with re- fueling or rough engine idling. Plastic wheel ornaments: The plastic wheel ornaments are damaged easily by organic substances. If any organic sub- stances splash an ornament, be sure to wash them off with water and check if the ornament is damaged. Aluminum wheels: Use only a mild soap or neutral detergent. Plastic bumpers: Wash carefully. Do not scrub with abrasive cleaners. The bumper faces are soft. Exterior lights: Wash carefully. Do not use organic substances or scrub them with a hard brush. This may damage the sur- faces of the lights.

Automatic car wash Your vehicle may be washed in an auto- matic car wash, but remember that the paint can be scratched by some types of brushes, unfiltered washing water, or the washing process itself. Scratching reduces paint durability and gloss, especially on darker colors. The manager of the car wash should be able to advise you wheth- er the process is safe for the paint on your vehicle. Waxing your Toyota Polishing and waxing is recommended to maintain the original beauty of your Toyota’s finish. Apply wax once a month or if the vehicle surface does not repel water well. 1. Always wash and dry the vehicle be- fore you begin waxing, even if you are using a combined cleaner and wax.

2. Use a good quality polish and wax. If the finish has become extremely weath- ered, use a car−cleaning polish, fol- lowed by a separate wax. Carefully fol- low the manufacturer’s instructions and precautions. Be sure to polish and wax the chrome trim as well as the paint.

335

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Cleaning the interior

CAUTION

D Be careful not to splash water or spill liquid on the floor. This may prevent the side airbags from acti- vating correctly, resulting in serious injury.

D Do not wash the vehicle interior or trunk with water. The hybrid battery is located behind the rear seat and allowing water to come into contact with the battery can cause electric shock that may result in death or serious injury.

Windshield washer nozzles: Make sure that the nozzles do not become blocked If a nozzle becomes when waxing. blocked, contact your Toyota dealer to have the vehicle serviced.

NOTICE

If a nozzle becomes blocked, do not try to clear it with a pin or other object. The nozzle will be damaged.

Exterior lights: Do not apply wax on the surfaces of the lights. Wax may cause damage to the lenses. If you accidentally put wax on the light surfaces, wipe or wash it off. 3. Wax

the vehicle again when water does not bead but remains on the sur- face in large patches.

Vinyl interior The vinyl upholstery may be easily cleaned with a mild soap or detergent and water. First vacuum over the upholstery to re- move loose dirt. Then, using a sponge or soft cloth, apply the soap solution to the vinyl. After allowing it to soak in for a few minutes to loosen the dirt, remove the dirt and wipe off the soap with a clean damp cloth. If all the dirt do not come off, re- peat the procedure. Commercial foaming− type vinyl cleaners are also available which work well. Follow the manufacturer’s instructions.

NOTICE

Do not use solvent, thinner, gasoline or window cleaner on the interior.

336

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Windows The windows may be cleaned with any household window cleaner.

NOTICE

When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.

Air conditioning control panel, audio panel, instrument panel, console panel and switches. Use a soft damp cloth for cleaning. Soak a clean soft cloth in water or luke- warm water then lightly wipe off dirt.

NOTICE

z Do not use organic substances (sol- vents, kerosene, alcohol, gasoline, etc.) or alkaline or acidic solutions. These chemicals can cause discol- oring, staining or peeling of the surface.

z If you use cleaners or polishing agents, make sure their ingredients do not include the substances men- tioned above.

z If you use a liquid car freshener, do not spill the liquid onto the ve- hicle’s interior surfaces. It may con- ingredients mentioned a- tain the bove. Immediately clean any spill using the method mentioned above.

to

foam−type shampoo

Carpets Use a good clean the carpets. Begin by vacuuming thoroughly to remove as much dirt as possible. Several types of foam cleaners are available; some are in aerosol cans and others are powders or liquids which you mix with water to pro- duce a foam. To shampoo the carpets, use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water—the best results are obtained by keeping the carpet as dry as possible. Read the shampoo instructions and follow them closely. Seat belts The seat belts may be cleaned with mild soap and water or with lukewarm water. Use a cloth or sponge. As you are clean- ing, check the belts for excessive wear, fraying, or cuts.

NOTICE

z Do not use dye or bleach on the

belts—it may weaken them.

z Do not use the belts until they be-

come dry.

337

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Leather interior The leather upholstery may be cleaned with neutral detergent for wool. Remove dirt using a soft cloth dampened with 5% solution of neutral detergent for wool. Then thoroughly wipe off all traces of detergent with a clean damp cloth. After cleaning or whenever any part of the leather gets wet, dry with a soft clean cloth. Allow the leather to dry in a venti- lated shaded area.

NOTICE

z If a stain should fail to come out with a neutral detergent, apply a cleaner that does not contain an organic solvent.

z Never use organic substances such as benzine, alcohol or gasoline, or alkaline or acid solutions for clean- ing these could cause discoloring.

leather as

the

z Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather.

338

’07Camry hybrid_U (L/O 0610)

z Mildew may develop on soiled leath- er upholstery. Be especially careful to avoid oil spots. Try to keep your upholstery always clean.

to direct sunlight z Long exposure may cause the leather surface to harden and shrink. Keep your ve- hicle in a shaded area, especially in the summer.

z The interior of your vehicle is apt to heat up on hot summer days, so avoid placing on the upholstery items made of vinyl or plastic or containing wax as these tend to stick to leather when warm.

z Improper cleaning of the leather up- in discolor-

holstery could result ation or staining.

If you have any questions about the cleaning of your Toyota, your local Toyota dealer will be pleased to answer them.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

339

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 6

VEHICLE MAINTENANCE AND CARE Vehicle maintenance and care Maintenance requirements General maintenance Does your vehicle need repairing? Emissions Inspection and Maintenance (I/M) programs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

341
342
344
345

For scheduled maintenance “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

information, please refer

to

the

340

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Maintenance requirements Your Toyota vehicle has been designed for fewer maintenance requirements with long- er service intervals to save both your time and money. However, each regular mainte- nance, as well as day−to−day care, is more important than ever before to ensure smooth, trouble−free, safe, and economical drivings. It is the owner’s responsibility to make sure the specified maintenance, including general maintenance service, is performed. Note that both the new vehicle and emis- sion control system warranties specify that proper maintenance and care must be per- formed. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for complete warranty information. General maintenance General maintenance items are those day− to−day care practices that are important to your vehicle for proper operation. It is the owner’s responsibility to insure that the general maintenance items are performed regularly. These checks or inspections can be done either by yourself or a qualified technician, or if you prefer, your Toyota dealer will be pleased to do them at a nominal cost.

Scheduled maintenance The scheduled maintenance items listed in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement” are those required to be serviced at regular inter- vals. For details of your maintenance schedule, read the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any replacement parts used for maintenance or for the repair of the emission control system be Toyota supplied. The owner may elect to use non−Toyota supplied parts replacement pur- poses without invalidating the emission control system warranty. However, use of replacement parts which are not of equivalent quality may impair the effec- tiveness of the emission control sys- tems. You may also elect to have mainte- nance, replacement, or repair of the emission control devices and system performed by any automotive repair es- tablishment or individual without invali- dating this warranty. See “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement” for complete war- ranty information.

for

Where to go for service? Toyota technicians are well−trained spe- cialists and are kept up to date with the latest service information through technical bulletins, service tips, and in−dealership training programs. They learn to work on Toyotas before they work on your vehicle, rather than while they are working on it. You can be confident that your Toyota dealer’s service department performs the best job to meet the maintenance require- ments on your vehicle—reliably and eco- nomically. Your copy of the repair order is proof that all required maintenance has been per- formed for warranty coverage. If any prob- lems should arise with your vehicle while under warranty, your Toyota dealer will promptly take care of it. Again, be sure to keep a copy of the repair order for any service performed on your Toyota.

341

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

the

items

listed,

General maintenance Listed below are the general maintenance items that should be performed as fre- quently as specified. In addition to check- ing if you notice any unusual noise, smell or vibration, you should investigate the cause or take your vehicle to your Toyota dealer or a quali- fied service shop immediately. It is recom- mended that any problem you notice be brought to the attention of your dealer or the qualified service shop for their advice.

CAUTION

Make these checks only with ade- quate ventilation if the hybrid system is operating.

What about do−it−yourself maintenance? Many of the maintenance items are easy to do yourself if you have a little mechani- cal ability and a few basic automotive tools. Simple instructions for how to per- form them are presented on page 346 in Section 7. If you are a skilled do−it−yourself mechan- ic, the Toyota service manuals are recom- mended. Please be aware that do−it−your- self maintenance can affect your warranty coverage. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for the details.

342

IN THE ENGINE COMPARTMENT Items listed below should be checked from time to time, e.g. each time when refueling. Washer fluid Make sure there is sufficient fluid in the tank. See page 373 in Section 7−3 for additional information. Coolant level Make sure the coolant level is between the full and low lines on the see−through reservoir when the hybrid system is cold. See page 357 in Section 7−2 for addition- al information. Radiator, condenser and hoses Check that the front of the radiator and condenser are clean and not blocked with leaves, dirt or insects. See page 358 in Section 7−2 for additional information. Brake fluid level Make sure the brake fluid level is correct. See page 359 in Section 7−2 for addition- al information. Engine oil level Check the level on the dipstick with the engine turned off and the vehicle parked on a level spot. See page 355 in Section 7−2 for additional information.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Exhaust system If you notice any change in the sound of the exhaust or smell exhaust fumes, have the cause located and corrected immedi- ately. See “Engine exhaust cautions” on page 278 in Section 2. IN THE TRUNK 12 volt battery condition See page 369 in Section 7−3 for addition- al information. INSIDE THE VEHICLE Items listed below should be checked regularly, e.g. while performing periodic services, cleaning the vehicle, etc. Lights Make sure the headlights, stop lights, tail lights, turn signal lights, and other lights are all working. Check headlight aim. Service reminder indicators and warning buzzers Check that all service reminder indicators and warning buzzers function properly. Steering wheel Be alert for changes in steering condition, such as hard steering or strange noise.

the

that

Seats Check that all front seat controls such as seat adjusters, seatback recliner, etc. op- erate smoothly and that all latches lock securely in any position. Check that the head restraints move up and down smoothly and that the locks hold securely in any latched position. For folding−down rear seatbacks, check latches lock securely. Seat belts Check that the seat belt system such as buckles, retractors and anchors operate properly and smoothly. Make sure that the belt webbings not cut, frayed, worn or damaged. Accelerator pedal Check the pedal for smooth operation and uneven pedal effort or catching. Brake pedal Check the pedal for smooth operation and that the pedal has the proper clearance. Check the brake booster function. Brakes In a safe place, check that the brakes do not pull to one side when applied.

Parking brake Check that the pedal has the proper travel and that, on a safe incline, your vehicle is held securely with only the parking brake applied. Transmission “Park” mechanism Check the lock release button of the se- lector lever for proper and smooth opera- tion. On a safe incline, check that your vehicle is held securely with the selector lever in “P” position and all brakes re- leased. OUTSIDE THE VEHICLE Items listed below should be performed from time, unless otherwise specified. Fluid leaks Check underneath for leaking fuel, oil, wa- ter or other the vehicle has been parked for a while. If you smell fuel fumes or notice any leak, have the cause found and corrected immediately. Doors and engine hood Check that all doors including trunk lid operate smoothly and all latches lock se- curely. Make sure the engine hood sec- ondary latch secures the hood from open- ing when the primary latch is released.

fluid after

time

to

343

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Tire inflation pressure Check the pressure with a gauge ev- ery two weeks, or at least once a month. See page 359 in Section 7−2
for additional information. Tire surface and wheel nuts Check the tires carefully for cuts, damage or excessive wear. See page 362 in Section 7−2 for additional in- formation. When checking the tires, make sure no nuts are missing, and check the nuts for looseness. Tighten them if necessary. Tire rotation Rotate the tires according to the maintenance schedule. (For sched- uled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supple- ment”.) See page 364 in Section 7−2
for additional information.

344

tip−offs

for changes

Does your vehicle need repairing? Be on the alert in perfor- mance, sounds, and visual that indicate service is needed. Some impor- tant clues are as follows: D Engine missing, stumbling, or pinging D Appreciable loss of power D Strange engine noises D A leak under the vehicle (however, wa- ter dripping from the air conditioning after use is normal.)

D Change

in exhaust sound (This may indicate a dangerous carbon monoxide leak. Drive with the windows open and have the exhaust system checked im- mediately.)

D Flat−looking tire; excessive tire squeal

when cornering; uneven tire wear

D Vehicle pulls to one side when driving

straight on a level road

D Strange noises related to suspension

movement

D Loss of brake effectiveness; spongy feeling brake pedal; pedal almost touches floor; vehicle pulls to one side when braking

D Coolant temperature continuously high-

er than normal

If you notice any of these clues, take your vehicle to your Toyota dealer as soon as possible. It probably needs adjustment or repair.

CAUTION

Do not continue driving with the ve- hicle unchecked. It could result in se- rious vehicle damage and possibly personal injury.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

indicator

the malfunction

in- include OBD

Emissions Inspection and Maintenance (I/M) programs Some states have vehicle emission spection programs which (On−Board Diagnostics) checks. The OBD system monitors the operation of the emission control system. When the OBD system determines that a problem exists somewhere in the emission control system, lamp comes on. In this case, your vehicle may the I/M test and need to be not pass repaired. Contact your Toyota dealer to service the vehicle. Even lamp does not come on, your vehicle may not pass readiness codes have not been set in the OBD system. Readiness codes are automatically set during ordinary driving. However, when the 12 volt battery is disconnected or run down, the codes are erased. Also, de- pending on your driving habits, the codes may not be completely set.

the malfunction

indicator

test as

I/M

the

if

’07Camry hybrid_U (L/O 0610)

Also, if the malfunction indicator lamp had come on recently due to temporary mal- function such as a loose fuel tank cap, your vehicle may not pass the I/M test. The malfunction indicator lamp will go off after taking several driving trips, but the error code in the OBD system will not be cleared unless about 40 trips or more are taken. If your vehicle does not pass the I/M test even the malfunction indicator lamp does not come on, contact your Toyota dealer to prepare the vehicle for re−testing.

345

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 7− 1

DO−IT−YOURSELF MAINTENANCE Introduction Engine compartment overview Fuse locations Do−it−yourself service precautions Positioning the jack Parts and tools

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

347
348
348
350
351

346

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Engine compartment overview

1. Brake fluid reservoir 2. Engine oil filler cap 3. Engine oil level dipstick 4. Coolant reservoir (for inverter, traction

motor and motor generator)

5. Radiator (for engine) 6. Fuse block 7. Condenser 8. Electric cooling fans 9. Radiator (for inverter, traction motor

and motor generator)

10. Windshield washer fluid tank 11. Coolant reservoir (for engine)

347

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Fuse locations

Spare fuses

348

’07Camry hybrid_U (L/O 0610)

Do−it−yourself service precautions If you perform maintenance by yourself, be sure to follow the correct procedure given in this Section. You should be aware that improper or in- complete servicing may result in operating problems. Performing do−it−yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement for details and suggestions. This Section gives for those items that are relatively easy for an owner to perform. As explained in Section 6, there are still a number of items that must be done by a qualified technician with special tools. For information on tools and parts for do− it−yourself maintenance, see “Parts and tools” on page 351 in this Section. Utmost care should be taken when work- ing on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to ob- serve:

instructions only

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

CAUTION

D Never touch, remove or disassemble high voltage parts and cables. Touching, removing or disassem- bling those parts and cables can cause severe burns or electric shock that may result in death or serious injury. For the locations of high voltage parts and cables, see “—High voltage components” on page 7 in Section 1−1.

D When the hybrid system is on, keep tools away hands, clothing, and from (Removing rings, watches, and ties is advis- able.)

the moving

fan.

D Right after driving,

the engine compartment—the engine, radiator, exhaust manifold and spark plug boots, etc.—will be hot. So be care- ful not to touch them. Oil, fluids and spark plugs may also be hot.

D If the radiator is hot, do not remove the radiator cap or loosen the drain plugs to prevent burning yourself.

’07Camry hybrid_U (L/O 0610)

D Do not

leave anything

that may burn easily, such as paper or rags, in the engine compartment.

D When the hybrid system is operat- ing with the “READY” light on, the engine may suddenly start in some cases. When you inspect the engine compartment, be sure to turn off the hybrid system.

D Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.

D Be sure that the POWER” switch is off if you work near the electric cooling fans or radiator grille. With the “POWER” switch on, the elec- tric cooling fans will automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.

D Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc.

D Brake fluid can harm your hands or eyes and damage painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately. If you still feel uncomfortable with your hands or eyes, go to the doctor.

D Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your skin, wash thoroughly with soap and water.

D Do not

leave used oil within the

reach of children.

D Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your dealer or a service station information concerning recycling or disposal.

for

D Be extremely cautious when work- ing on the 12 volt battery. It con- tains corrosive sulfuric acid.

poisonous

and

349

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Positioning the jack

NOTICE

z Remember that the 12 volt battery and ignition cables carry high cur- rents or voltages. Be careful of ac- cidentally causing a short circuit.

z Add only “Toyota Super Long Life Coolant” or similar high quality eth- ylene glycol based non−silicate, non−amine, non−nitrite, and non−bo- rate coolant with long−life hybrid organic acid technology to fill the radiator. “Toyota Super Long Life Coolant” is a mixture of 50% cool- ant and 50% deionized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).

z If you spill some of the coolant, be sure to wash it off with water to prevent it from damaging the parts or paint.

z Do not allow dirt or anything else to fall through the spark plug holes. z Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.

350

z Do not reuse iridium−tipped spark

plugs by cleaning or regapping.

z Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.

z Be careful not to scratch the glass

surface with the wiper frame.

z When closing

the engine hood, check to see that you have not for- gotten any tools, rags, etc.

Front

Rear

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

When jacking up your vehicle with the jack, position jack correctly as shown in the illustrations.

the

CAUTION

When jacking, be sure to observe the following to reduce the possibility of death or serious injury: D Follow jacking instructions. D Do not put any part of your body under the vehicle supported by the jack. Personal injury may occur.

D Do not start

the hybrid system while your vehicle is supported by the jack.

D Stop the vehicle on a

level firm ground, firmly set the parking brake and put the transmission in “P”. Block the wheels on the opposite side of the jack up point if neces- sary.

D Make sure to set the jack properly in the jack point. Raising the ve- hicle with improperly posi- tioned will damage the vehicle or may allow the vehicle to fall off the jack and cause personal injury.

jack

’07Camry hybrid_U (L/O 0610)

D Never get under the vehicle when the vehicle is supported by the jack alone; use vehicle support stands. D Do not raise the vehicle with some-

one in the vehicle.

D When raising the vehicle, do not place any objects on top of or un- derneath the jack.

NOTICE

Make sure to place the jack correctly, or your vehicle may be damaged.

Parts and tools Here is a list of parts and tools you will need to perform do−it−yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. CHECKING THE ENGINE OIL LEVEL Parts (if level is low): D “Toyota Genuine Motor Oil” or equiva-

lent See page 356 in Section 7−2 for de- tails about engine oil selection.

Tools: D Rag or paper towel D Funnel (only for adding oil)

351

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

CHECKING AND REPLACING FUSES Parts (if replacement is necessary): D Genuine Toyota fuse or equivalent with

same amperage rating as original

ADDING WASHER FLUID Parts: D Water D Washer fluid containing antifreeze (for

winter use)

Tools: D Funnel REPLACING LIGHT BULBS Parts: D Bulb with same number and wattage rating as original (See charts in “Re- placing in Section 7−3.)

light bulbs” on page 373

CHECKING THE COOLANT LEVEL Parts (if level is low): D “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−ni- trite, and non−borate coolant with long− life hybrid organic acid technology. “Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion- ized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).

Tools: D Funnel (only for adding coolant) CHECKING 12 VOLT BATTERY CON- DITION Tools: D Warm water D Baking soda D Grease D Conventional wrench

terminal

(for

clamp bolts)

352

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

353

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

SECTION 7− 2

DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level Checking the coolant level Checking the radiator and condenser Checking brake fluid Checking tire inflation pressure Checking and replacing tires Rotating tires Installing snow tires and chains Replacing wheels Aluminum wheel precautions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

355
357
358
359
359
362
364
365
367
367

354

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

Checking the engine oil level

Low level

Full level

Add oil

O.K.

Too full

With the hybrid system at operating temperature and turned off, check the oil level on the dipstick. 1. To get a correct reading, the vehicle should be on level ground. After turning off the hybrid system, wait a few min- utes for the oil to drain back into the bottom of the engine.

2. Pull the dipstick out, hold a rag under

the end and wipe it clean.

3. Reinsert the dipstick—push it in as far as it will go, or the reading will not be correct.

4. Pull the dipstick out and look at the oil the

level while holding a rag under end.

’07Camry hybrid_U (L/O 0610)

CAUTION

NOTICE

z Be careful not to spill engine oil on

the vehicle components.

z Avoid overfilling, or

could be damaged.

the engine

z Check the oil level on the dipstick

once again after adding the oil.

Be careful not to touch the hot ex- haust manifold.

NOTICE

Be careful not to drop engine oil on the vehicle components.

If the oil level is below or only slightly above the low level line, add engine oil of the same type as already in the en- gine. Remove the oil filler cap and add engine oil in small quantities at a time, checking the dipstick. We recommend that you use a funnel when adding oil. The approximate quantity of oil needed to raise the level between low and full on the dipstick is indicated as follows: 1.1 L (1.2 qt., 1.0 Imp. qt.)

For the engine oil capacity, see “Service specifications” on page 382 in Section 8. When the level reaches within the correct range, install the filler cap hand−tight.

355

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

ENGINE OIL SELECTION “Toyota Genuine Motor Oil” in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to grade and viscosity. Oil grade:

following

is used

satisfy

the

ILSAC multigrade engine oil

Recommended viscosity: SAE 5W−20 or 0W−20

Outside temperature

SAE 5W−20 or 0W−20 engine oil may be used. However, SAE 0W−20 is the best choice for good fuel economy and good starting in cold weather.

356

Oil identification mark The ILSAC (International Lubricant Stan- dardization and Approval Committee) Certi- fication Mark is added to some oil con- tainers the oil you should use.

to help you select

To ensure excellent lubrication perfor- mance for your engine, “Toyota Genuine Motor Oil” is available, which has been specifically for all Toyota engines. Please contact your Toyota dealer for fur- ther details about “Toyota Genuine Motor Oil”.

tested and approved

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Checking the coolant level

in

the system. Visually check

If the coolant level drops within a short time after replenishing, there may be a leak the radiator, hoses, coolant filler cap, radiator cap and drain cock and water pump. If you can find no leak, have your Toyota dealer test the cap pressure and check for leaks in the cooling system.

Coolant reservoir for engine

Coolant reservoir for inverter, traction mo- tor and motor generator

CAUTION

To prevent burning yourself, do not remove the radiator cap when the hy- brid system is hot.

(For

the coolant

Look at the see−through coolant reser- voir when the hybrid system is cold. The coolant level is satisfactory if it is between the “F” and “L” lines on the reservoir. If the level is low, add the coolant. type, see “Coolant type selection” described be- low.) The coolant level in the reservoir will vary with the hybrid system temperature. How- ever, if the level is on or below the “L” line, add coolant. Bring the level up to the “F” line.

(For

the coolant

Look at the see−through coolant reser- voir when the hybrid system is cold. The coolant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir. If the level is low, add coolant. type, see “Coolant type selection” described be- low.) The coolant level in the reservoir will vary with the hybrid system temperature. How- ever, if the level is on or below the “LOW” line, add coolant. Bring the level up to the “FULL” line.

improper coolants may damage

Coolant type selection Use of your cooling system. Only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−nitrite, and non−borate coolant with long−life technology. (Coolant hybrid organic acid acid with technology low phosphates and organic acids.)

combination of

long−life

organic

hybrid

is a

357

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

For the U.S.A.—“Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deionized water. This coolant pro- vides protection down to about −35_C (−31_F). For Canada—“Toyota Super Long Life Coolant” is a mixture of 55% coolant and 45% deionized water. This coolant pro- vides protection down to about −42_C (−44_F).

NOTICE

Do not use plain water alone.

Toyota recommends “Toyota Super Long Life Coolant”, which has been tested to ensure that it will not cause corrosion nor result in malfunction of your coolant system with proper usage. “Toyota Super formulated with Long Life Coolant” technology long−life hybrid organic acid and has been specifically designed to system malfunction on cooling avoid Toyota vehicles. Please contact your Toyota dealer further details.

for

is

Checking the radiator and condenser If any of the above parts are extremely dirty or you are not sure of their condi- tion, take your vehicle to a Toyota dealer.

CAUTION

To prevent burning yourself, be care- ful not to touch the radiator or con- denser when they may be hot after driving.

NOTICE

To prevent damage to the radiator and condenser, do not perform the work by yourself.

358

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Checking brake fluid

Checking tire inflation pressure

reservoir. The

To check the fluid level, simply look at the see−through level should be between the “MAX” and “MIN” lines on the reservoir. It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high. If the level is low, take your vehicle to a Toyota dealer as soon as possible. Do not drive your vehicle if the red brake system warning is on. Call a Toyota dealer for assistance.

light

If the fluid level goes down soon after your vehicle is serviced, it may indicate a serious mechanical problem. Have your vehicle checked by a Toyota deal- er.

CAUTION

Brake fluid can harm your hands or eyes. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately. If you still feel uncomfortable with your hands or eyes, go to the doctor.

NOTICE

If brake fluid is spilled on the vehicle, be sure to wipe it off to prevent dam- age to parts or paint.

Type A

359

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Keep your tire inflation pressures at the proper level. The recommended cold tire inflation pressures, tire sizes and the com- bined weight of occupants and cargo (vehicle capacity weight) are de- scribed on page 385 and 380. They are also on the tire and loading infor- mation label. You should check the tire inflation pressure every two weeks, or at least once a month. And do not forget the spare!

Type B

360

should

pressure

following

instructions

The for checking tire inflation pressure should be observed: D The

be checked only when the tires are cold. If your vehicle has been parked for at least 3 hours and has not been driven for more than 1.5
km or 1 mile since, you will get an accurate cold tire inflation pres- sure reading.

D Always use a tire pressure gauge. The appearance of a tire can be misleading. Besides, tire inflation pressures that are even just a few pounds off can degrade ride and handling.

D Take special care when adding air to the compact spare tire. The smaller tire size can gain pressure very quickly. Add com- pressed air in small quantities and check the pressure often until it reaches the specified pressure.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

D Do not bleed or reduce tire inflation pressure after driving. It is normal for the tire inflation pressure to be higher after driving. D Never exceed the vehicle capac- ity weight. Passenger and lug- gage weight should be located so that the vehicle is balanced.

Tire pressure gauge

INSPECTION AND ADJUSTMENT PROCEDURE 1. Remove the tire valve cap. 2. Press the tip of the tire pressure

gauge to the tire valve.

3. Read the pressure using the grad-

uations of the gauge.

4. In case the tire inflation pressure is not within the prescribed range, insert the compressed air from the valve. In case of applying too much air, press the center of the valve and release the air to adjust.

5. After completing the tire inflation pressure measurement and ad- justment, apply soapy water to the valve and check for leakage.

6. Install the tire valve cap. If a gauge and air pump are not avail- able, have your vehicle checked by your Toyota dealer.

CAUTION

Be sure to reinstall the tire valve caps. Without the valve caps, dirt or moisture could get into the valve core and cause air leakage. If the caps have been lost, have new ones put on as soon as pos- sible.

Incorrect tire inflation pressure may waste fuel, reduce the comfort of driv- ing, reduce tire life and make your ve- hicle less safe to drive. If a tire frequently needs refilling, have it checked by your Toyota deal- er.

361

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

CAUTION

Keep your tires properly inflated. Otherwise, the following condi- tions may occur and cause an ac- cident resulting in death or seri- ous injuries. Low tire pressure (underinfla- tion)— D Excessive wear D Uneven wear D Poor handling D Possibility of blowouts from a

overheated tire

D Poor sealing of the tire bead D Wheel deformation and/or tire

separation

D A greater possibility of tire

damage from road hazards

362

’07Camry hybrid_U (L/O 0610)

Checking and replacing tires

Tread wear indicator

High tire pressure (overinfla- tion)— D Poor handling D Excessive wear D Uneven wear D A greater possibility of tire

damage from road hazards

CHECKING YOUR TIRES Check the tire’s tread for tread wear indicators. If the indicators show, replace the tires. The loca- tion of tread wear indicators is shown by the “TWI” or “Δ” marks, etc., molded on the sidewall of each tire.

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

If air loss occurs while driving, do not continue driving. Driving even a short distance can damage a tire beyond repair. Any tires which are over 6 years old must be checked by a qualified technician even if damage is not obvious. Tires deteriorate with age even if they have never or seldom been used. This applies also to the spare tire and tires stored for future use.

The tires on your Toyota have built−in tread wear indicators to help you know when the tires need replace- ment. When the tread depth wears to 1.6 mm (0.06 in.) or less, the indica- tors will appear. If you can see the indicators in two or more adjacent grooves, the tire should be replaced. The lower the tread, the higher the risk of skidding. The effectiveness of snow tires is lost if the tread wears down below 4 mm (0.16 in.). If you have tire damage such as cuts, splits, cracks deep enough to expose the fabric, or bulges indi- cating internal damage, the tire should be replaced. If a tire often goes flat or cannot be properly repaired due to the size or location of a cut or other damage, it should be replaced. If you are not sure, consult with your Toyota dealer.

REPLACING YOUR TIRES When replacing a tire, use a tire of the same size and construction, and the same or greater maximum load as the originally installed tires. Using any other size or type of tire may seriously affect handling, ride, speedometer/odometer calibration, ground clearance, and clearance be- tween the body and tires or snow chains. Check that the maximum load of the replaced tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater. As for the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire, and as for the Gross Axle Weight Ratings (GAWR), see the Cer- tification Label. For details about the side wall of the tire and the Certification Label, see pages 285 and 283.

363

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Rotating tires

CAUTION

Observe the following instruc- tions. Otherwise, an accident may occur resulting in death or serious injuries. D Do not mix radial, bias belted, or bias−ply tires on your ve- hicle, as this may cause dan- gerous handling characteris- tics resulting in loss of control. D Do not use tires other than the manufacturer’s recommended size, as this may cause danger- ous handling characteristics resulting in loss of control.

Toyota recommends all four tires, or at least both of the front or rear tires be replaced at a time as a set. See “If you have a flat tire” on page 318 in Section 4 for tire change proce- dure. When a tire is replaced, the wheel should always be balanced. An unbalanced wheel may affect ve- hicle handling and tire life. Wheels can get out of balance with regular use and should therefore be balanced occasionally. When replacing a tubeless tire, the air valve should also be replaced with a new one. Initial adjustment of the tire pres- sure warning system is necessary after you have replaced your tires. See “Tire pressure warning sys- tem” on page 168 in Section 1−7.

364

To equalize the wear and help ex- tend tire life, Toyota recommends that you rotate your tires accord- ing to the maintenance schedule. (For scheduled maintenance infor- mation, please refer to the “Sched- uled Maintenance Guide” or “Own- er’s Supplement”.) However, the most appropriate tim- ing for tire rotation may vary ac- cording to your driving habits and road surface conditions.

Manual

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

See “If you have a flat tire” on page 318 in Section 4 for tire change proce- dure. When rotating tires, check for uneven wear and damage. Abnormal wear is usually caused by incorrect tire pres- sure, improper wheel alignment, out− of−balance wheels, or severe braking. Initial adjustment of the tire pres- sure warning system is necessary after you have rotated your tires. See “Tire pressure warning sys- tem” on page 168 in Section 1−7.

CAUTION

Do not include a compact spare tire when rotating the tires. It is designed for temporary use only.

Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select tires of the same size, construction and load capacity as the originally installed tires. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions.

CAUTION

Do not use snow tires other than the manufacturer’s recommended size, as this may cause dangerous handling characteristics resulting loss of control. Otherwise, an accident may occur resulting in death or serious injuries.

in

SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the front wheels only can lead to an excessive difference in road grip capability between the front and rear tires which could cause loss of vehicle control. When storing removed tires you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replac- ing.

CAUTION

D Do not drive with the snow tires

incorrectly inflated.

D Never drive over 120 km/h (75 mph)

with any type of snow tires.

TIRE CHAIN SELECTION Use the tire chains of correct size.

365

2007 CAMRY HV from Oct. ’06 Prod. (OM33749U)

’07Camry hybrid_U (L/O 0610)

Side chain

Regulations regarding the use of tire chains vary according to location or type of road, so always check local reg- ulations before installing chains.

NOTICE

Cross chain

If the wrong combination of tire and chain is used, the chains could dam- age the vehicle body.

the

rear driving

CHAIN INSTALLATION Install the chains on the front tires as tightly as possible. Do not use tire tires. Retighten chains on chains after