2015 Toyota 4runner Owners Manual

Stop the vehicle. Press and hold the “SLIDE (open/close)” switch in the close position.*1
The moon roof will close, reopen and pause for approximately 10 sec- onds.*2 Then it will close again, tilt up and pause for approximately 1 sec- ond. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.

●If the moon roof tilts down but then tilts back up

Stop the vehicle. Press and hold the “UP” switch*1 until the moon roof moves into the tilt up position and stops. Release the “UP” switch once and then press and hold the “UP” switch again.*1
The moon roof will pause for approximately 10 seconds in the tilt up posi- tion.*2 Then it will adjust slightly and pause for approximately 1 second. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.

*1: If the switch is released at the incorrect time, the procedure will have to

be performed again from the beginning.

*2: If the switch is released after the above mentioned 10 second pause, automatic operation will be disabled. In that case, press and hold the “UP” or “DOWN” switch, and the moon roof will tilt up and pause for approximately 1 second. Then it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.

If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.

■Moon roof open reminder function

An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the engine switch off.

■Door lock linked moon roof operation ●The moon roof can be opened and closed using the key or mechanical key.* (P. 97, 445) ●The moon roof can be opened using the wireless remote control.* (P. 96) *: These settings must be customized at your Toyota dealer.

4RUNNER (U)_(OM35B18U)

3

3-5. Opening, closing the windows and moon roof

155

■Customization that can be configured at Toyota dealer

Settings (e.g. key linked operation) can be changed. (Customizable features P. 481)

CAUTION

Observe the following precautions. Failure to do so may cause death or serious injury. ■Opening the moon roof

●Do not allow any passengers to put their hands or heads outside the vehi-

cle while it is moving.

●Do not sit on top of the moon roof.

■Closing the moon roof

●The driver is responsible for moon roof opening and closing operations.

In order to prevent accidental operation, especially by a child, do not let a child operate the moon roof. It is possible for children and other passen- gers to have body parts caught in the moon roof.

●Check to make sure that all passengers do not have any part of their body in a position where it could be caught when the moon roof is being oper- ated.

●When using the key or mechanical key and operating the moon roof, oper- ate the moon roof after checking to make sure that there is no possibility of any passenger having any of their body parts caught in the moon roof. Also, do not let a child operate moon roof by the key or mechanical key. It is possible for children and other passengers to get caught in the moon roof.

●When exiting the vehicle, turn the engine switch off, carry the key and exit the vehicle along with the child. There may be accidental operation, due to mischief, etc., that may possibly lead to an accident.

■Jam protection function

●Never use any part of your body to intentionally activate the jam protection

function.

●The jam protection function may not work if something gets caught just

before the moon roof fully closes.

4RUNNER (U)_(OM35B18U)

156

3-5. Opening, closing the windows and moon roof

4RUNNER (U)_(OM35B18U)

Driving

157

4-1. Before driving

Driving the vehicle............. 158
Cargo and luggage ........... 168
Vehicle load limits ............. 173
Trailer towing..................... 174
Dinghy towing ................... 190

4-2. Driving procedures

Engine (ignition) switch (vehicles without a smart key system)........... 191
Engine (ignition) switch (vehicles with a smart key system)........... 194
Automatic transmission..... 199
Turn signal lever................ 202
Parking brake.................... 203

4-3. Operating the lights and

wipers Headlight switch................ 204
Fog light switch ................. 210
Windshield wipers and washer ............................ 212
Rear window wiper and washer ............................ 215

4-4. Refueling

Opening the fuel tank cap .................................. 218

4-5. Using the driving support systems Cruise control.................... 221
Intuitive parking assist....... 225
Four-wheel drive system (part-time 4WD models) ........................... 231
Four-wheel drive system (full-time 4WD models) ........................... 235
Active traction control system ............................ 239
AUTO LSD system............ 241
Rear differential lock system ............................ 243
Downhill assist control system ............................ 246
Crawl Control .................... 249
Multi-terrain Select ............ 252
Driving assist systems ...... 259

4-6. Driving tips

Winter driving tips ............. 268
Off-road precautions ......... 272

4RUNNER (U)_(OM35B18U)

158

4-1. Before driving

Driving the vehicle

The following procedures should be observed to ensure safe driving:

Starting the engine P. 194
Driving

With the brake pedal depressed, shift the shift lever to D. (P. 199) Release the parking brake. (P. 203) Gradually release the brake pedal and gently depress the accelera- tor pedal to accelerate the vehicle.

Stopping

With the shift lever in D, depress the brake pedal until the vehicle comes to a stop. If necessary, set the parking brake. If the vehicle is to be stopped for an extended period of time, shift the shift lever to P or N. (P. 199)

Parking the vehicle

With the shift lever in D, depress the brake pedal. Set the parking brake. (P. 203) Shift the shift lever to P. (P. 199) If parking on a hill, block the wheels as needed. Vehicles without a smart key system: Turn the engine switch to the “LOCK” position to stop the engine. Vehicles with a smart key system: Press the engine switch to stop the engine. Lock the door, making sure that you have the key on your person.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

159

Starting off on a steep uphill

Make sure that the parking brake is set and shift the shift lever to D. Gently depress the accelerator pedal. Release the parking brake.

■Driving in the rain

●Drive carefully when it is raining, because visibility will be reduced, the win-

dows may become fogged-up, and the road will be slippery.

●Drive carefully when it starts to rain, because the road surface will be espe-

cially slippery.

●Refrain from driving at high speeds in the rain, as there may be a layer of water between the tires and the road surface, preventing the steering and brakes from operating properly.

■Engine speed while driving

In the following conditions, the engine speed may become high while driving. This is due to automatic up-shifting control or down-shifting implementation to meet driving conditions. It does not indicate sudden acceleration. ●The vehicle is judged to be driving uphill or downhill ●When the accelerator pedal is released

■Breaking in your new Toyota

To extend the life of the vehicle, observing the following precautions is recom- mended: ●For the first 200 miles (300 km):

Avoid sudden stops.

●For the first 500 miles (800 km):

Do not tow a trailer.

●For the first 1000 miles (1600 km):

• Do not drive at extremely high speeds. • Avoid sudden acceleration. • Do not drive continuously in low gears. • Do not drive at a constant speed for extended periods.

4RUNNER (U)_(OM35B18U)

160

4-1. Before driving

■Drum-in-disc type parking brake system

Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or whenever the parking brake shoes and/or drum are replaced. Have your Toyota dealer per- form the bedding down operation.

■Operating your vehicle in a foreign country

Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (P. 466) ■When turning off the engine

The emission system operating sounds may continue for a short time after the engine is turned off. This is not a malfunction, and helps to ensure optimal performance of the emission system.

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■When starting the vehicle

Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.

■When driving the vehicle

●Do not drive if you are unfamiliar with the location of the brake and accel-

erator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake

pedal will result in sudden acceleration that may lead to an accident.

• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly. This allows you to depress the brake and accelera- tor pedals properly.

• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.

●Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. These hot parts may cause a fire if there is any flammable material nearby.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

161

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■When driving the vehicle

●During normal driving, do not turn off the engine. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so. However, in the event of an emergency, such as if it becomes impossible to stop the vehicle in the normal way: P. 401

●Use engine braking (downshift) to maintain a safe speed when driving

down a steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (P. 199)

●Do not adjust the positions of the steering wheel, the seat, or the inside or

outside rear view mirrors while driving. Doing so may result in a loss of vehicle control.

●Always check that all passengers’ arms, heads or other parts of their body

are not outside the vehicle.

●Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires. Driving over 85 mph (140 km/h) may result in tire failure, loss of control and possible injury. Be sure to consult a tire dealer to determine whether the tires on your vehicle are high-speed capability tires or not before driving at such speeds.

4RUNNER (U)_(OM35B18U)

162

4-1. Before driving

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■When driving on slippery road surfaces

●Sudden braking, acceleration and steering may cause tire slippage and

reduce your ability to control the vehicle, resulting in an accident.

●Sudden acceleration, engine braking due to shifting, or changes in engine

speed could cause the vehicle to skid, resulting in an accident.

●After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.

■When shifting the shift lever

●Do not let the vehicle roll backward while the shift lever is in a driving posi-

tion, or roll forward while the shift lever is in R. Doing so may cause the engine to stall or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle.

●Do not shift the shift lever to P while the vehicle is moving.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Do not shift the shift lever to R while the vehicle is moving forward.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Do not shift the shift lever to D while the vehicle is moving backward.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Moving the shift lever to N while the vehicle is moving will disengage the engine from the transmission. Engine braking is not available when N is selected.

●Be careful not to shift the shift lever with the accelerator pedal depressed. Shifting the shift lever to a gear other than P or N may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

163

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■If you hear a squealing or scraping noise (brake pad wear limit indica-

tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage may result if the pads are not replaced when needed. It is dangerous to drive the vehicle when the wear limits of the brake pads and/or those of the brake discs are exceeded.

■When the vehicle is stopped

●Do not race the engine.

If the vehicle is in any gear other than P or N, the vehicle may accelerate suddenly and unexpectedly, causing an accident.

●In order to prevent accidents due to the vehicle rolling away, always keep depressing the brake pedal while the engine is running, and apply the parking brake as necessary.

●If the vehicle is stopped on an incline, in order to prevent accidents caused by the vehicle rolling forward or backward, always depress the brake pedal and securely apply the parking brake as needed.

●Avoid revving or racing the engine.

Running the engine at high speed while the vehicle is stopped may cause the exhaust system to overheat, which could result in a fire if combustible material is nearby.

4RUNNER (U)_(OM35B18U)

164

4-1. Before driving

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■When the vehicle is parked

fire.

●Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in

the vehicle when it is in the sun. Doing so may result in the following: • Gas may leak from a cigarette lighter or spray can, and may lead to a

• The temperature inside the vehicle may cause the plastic lenses and

plastic material of glasses to deform or crack.

• Soft drink cans may fracture, causing the contents to spray over the interior of the vehicle, and may also cause a short circuit in the vehicle’s electrical components.

●Do not leave cigarette lighters in the vehicle. If a cigarette lighter is in a place such as the glove box or on the floor, it may be lit accidentally when luggage is loaded or the seat is adjusted, causing a fire.

●Do not attach adhesive discs to the windshield or windows. Do not place containers such as air fresheners on the instrument panel or dashboard. Adhesive discs or containers may act as lenses, causing a fire in the vehi- cle.

●Do not leave a door or window open if the curved glass is coated with a metallized film such as a silver-colored one. Reflected sunlight may cause the glass to act as a lens, causing a fire.

●Always apply the parking brake, shift the shift lever to P, stop the engine

and lock the vehicle. Do not leave the vehicle unattended while the engine is running.

●Do not touch the exhaust pipes while the engine is running or immediately

after turning the engine off. Doing so may cause burns.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

165

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■When taking a nap in the vehicle

Always turn the engine off. Otherwise, if you accidentally move the shift lever or depress the accelerator pedal, this could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.

■When braking

●When the brakes are wet, drive more cautiously.

Braking distance increases when the brakes are wet, and this may cause one side of the vehicle to brake differently than the other side. Also, the parking brake may not securely hold the vehicle.

●If the power brake assist function does not operate, do not follow other

vehicles closely and avoid hills or sharp turns that require braking. In this case, braking is still possible, but the brake pedal should be depressed more firmly than usual. Also, the braking distance will increase.

●Do not pump the brake pedal if the engine stalls.

Each push on the brake pedal uses up the reserve for the power-assisted brakes.

●The brake system consists of 2 individual hydraulic systems; if one of the systems fails, the other will still operate. In this case, the brake pedal should be depressed more firmly than usual and the braking distance will increase. If this happens, do not continue to drive the vehicle. Have your brakes fixed immediately.

4RUNNER (U)_(OM35B18U)

166

4-1. Before driving

NOTICE

■When driving the vehicle

●Do not depress the accelerator and brake pedals at the same time during

driving, as this may restrain driving torque.

●Do not use the accelerator pedal or depress the accelerator and brake

pedals at the same time to hold the vehicle on a hill.

■When parking the vehicle

Always shift the shift lever to P. Failure to do so may cause the vehicle to move or the vehicle may accelerate suddenly if the accelerator pedal is accidentally depressed.

■Avoiding damage to vehicle parts

●Do not turn the steering wheel fully in either direction and hold it there for

an extended period of time. Doing so may damage the power steering pump.

●When driving over bumps in the road, drive as slowly as possible to avoid

damaging the wheels, underside of the vehicle, etc.

■If you get a flat tire while driving

A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually depress the brake pedal to slow down the vehi- cle. ●It may be difficult to control your vehicle. ●The vehicle will make abnormal sounds or vibrations. ●The vehicle will behave abnormally. Information on what to do in case of a flat tire (P. 428)

4RUNNER (U)_(OM35B18U)

4-1. Before driving

167

NOTICE

■When encountering flooded roads

Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle: ●Engine stalling ●Short in electrical components ●Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following: ●Brake function ●Changes in quantity and quality of oil and fluid used for the engine, trans-

mission, transfer (4WD models), differentials, etc.

●Lubricant condition for the propeller shaft, bearings and suspension joints

(where possible), and the function of all joints, bearings, etc.

4RUNNER (U)_(OM35B18U)

168

4-1. Before driving

Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load: ● Stow cargo and luggage in the luggage compartment whenever

possible.

● Be sure all items are secured in place. ● To maintain vehicle balance while driving, position luggage evenly

within the luggage compartment.

● For better fuel economy, do not carry unnecessary weight.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

169

Capacity and distribution Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) — (Total weight of occupants) Steps for Determining Correct Load Limit — (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard.

(2) Determine the combined weight of the driver and passengers that

will be riding in your vehicle.

(3) Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4) The resulting figure equals the available amount of cargo and lug-

gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400  750 (5150) = 650 lbs.)

(5) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

(6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (P. 456)

4RUNNER (U)_(OM35B18U)

170

4-1. Before driving

Calculation formula for your vehicle

Cargo capacity Total capacity weight) (P. 456)

load capacity

(vehicle

When 2 people with the combined weight of A lb. (kg) are riding in your vehicle, which has a total load capacity (vehicle capacity weight) of B lb. (kg), the available amount of cargo and luggage load capacity will be C lb. (kg) as follows: B*2 lb. (kg) - A*1 lb. (kg) = C*3 lb. (kg) *1: A =Weight of people *2: B =Total load capacity *3: C =Available cargo and luggage load

In this condition, if 3 more passengers with the combined weight of D lb. (kg) get on, the available cargo and luggage load will be reduced E lb. (kg) as follows:

C lb. (kg) - D*4 lb. (kg) = E*5 lb. (kg) *4: D =Additional weight of people *5: E =Available cargo and luggage load As shown in the example above, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

4RUNNER (U)_(OM35B18U)

4-1. Before driving

171

Roof rails

Cross rails

■When using the roof rails (if equipped) ●To use the roof rails as a roof luggage carrier, you must fit the roof rails with two or more genuine Toyota cross rails or their equivalent.

●When there is no luggage on the roof luggage carrier Toyota recommends that the front and rear cross rails be secured in the positions indicated in the illustration. This may reduce wind noise while driving.

CAUTION

■Things that must not be carried in the luggage compartment

The following things may cause a fire if loaded in the luggage compart- ment: ●Receptacles containing gasoline ●Aerosol cans

■Storage precautions

Observe the following precautions. Failure to do so may prevent the pedals from being depressed properly, may block the driver’s vision, or may result in items hitting the driver or passengers, possibly causing an accident. ●Stow cargo and luggage in the luggage compartment whenever possi-

ble.

●Do not stack cargo and luggage in the luggage compartment higher

than the seatbacks.

●Do not place cargo or luggage in or on the following locations.

• At the feet of the driver • On the front passenger or rear seats (when stacking items) • On the instrument panel • On the dashboard

●Secure all items in the occupant compartment. ●When you fold down the rear seats, long items should not be placed

directly behind the front seats.

●Never allow anyone to ride in the luggage compartment. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or serious bodily injury, in the event of sudden braking, sudden swerving or an accident.

4RUNNER (U)_(OM35B18U)

172

4-1. Before driving

CAUTION

■Capacity and distribution

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.

■When loading cargo on the roof luggage carrier

Observe the following precautions: ●Place the cargo so that its weight is distributed evenly between the

front and rear axles.

●If loading long or wide cargo, never exceed the vehicle overall length

or width. (P. 456)

●Before driving, make sure the cargo is securely fastened on the roof

luggage carrier.

●Loading cargo on the roof luggage carrier will make the center of grav- ity of the vehicle higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle correctly and result in death or serious injury.

●If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then during the trip to make sure the cross rails are fixed securely and that the cargo remains in its place.

●Do not exceed 120 lb. (54 kg) cargo weight on the roof luggage carrier.

NOTICE

■When loading cargo on the roof luggage carrier

Be careful not to scratch the surface of the moon roof (if equipped).

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

173

Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, TWR (Trailer Weight Rating) and cargo capacity.

◆ Total load capacity (vehicle capacity weight): (P. 456)

Total load capacity means the combined weight of occupants, cargo and luggage.

◆ Seating capacity

Vehicle without third seats: 5 occupants (Front 2, Rear 3) Vehicle with third seats: 7 occupants (Front 2, Rear 5) Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person.

◆ TWR (Trailer Weight Rating): (P. 179, 456)

TWR means the maximum gross trailer weight (trailer weight plus its cargo weight) that you vehicle is able to tow.

◆ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label. (P. 369)

CAUTION

■Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

4RUNNER (U)_(OM35B18U)

174

4-1. Before driving

Trailer towing

Your vehicle is designed primarily as a passenger-and-load-car- rying vehicle. Towing a trailer can have an adverse impact on handling, performance, braking, durability, and fuel consump- tion. For your safety and the safety of others, you must not over- load your vehicle or trailer. You must also ensure that you are using appropriate towing equipment, that the towing equipment has been installed correctly and used properly, and that you employ the requisite driving habits. Vehicle-trailer stability and braking performance are affected by trailer stability, brake performance and setting, trailer brakes, the hitch and hitch systems (if equipped). To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating conditions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about addi- tional requirements such as a towing kit, etc.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

175

Towing related terms ■ GCWR (Gross Combination Weight Rating)

the

The maximum allowable gross combination weight. The gross combination weight is the sum of total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the trailer).

the cargo

in

■ GVWR (Gross Vehicle Weight Rating)

The maximum allowable gross vehicle weight. The gross vehi- cle weight is the total weight of the vehicle. When towing a trailer, it is the sum of the vehi- cle weight (including the occu- pants, cargo and any optional equipment installed on the vehi- cle) and the tongue weight.

4RUNNER (U)_(OM35B18U)

176

4-1. Before driving

■ GAWR (Gross Axle Weight Rating)

The maximum allowable gross axle weight. The gross axle weight is the load placed on each axle (front and rear).

Front GAWR

Rear GAWR

(With brakes)

■ TWR (Trailer Weight Rating)

The maximum allowable gross trailer weight. The gross trailer weight is the sum of the trailer weight and the weight of the cargo in the trailer. TWR is calculated assuming base vehicle with one driver, one towing package (if available), hitch and hitch systems (if required).

front passenger,

Additional optional equipment, passengers and cargo in the vehicle will reduce the trailer weight rating so as not to exceed GCWR, GVWR and GAWR. If the gross trailer weight exceeds 3000 lb. (1360 kg), it is recommended to use a trailer with 2 or more axles.

4RUNNER (U)_(OM35B18U)

4-1. Before driving

177

■ Unbraked TWR (Unbraked Trailer Weight Rating)

The trailer weight rating for tow- ing a trailer without a trailer ser- vice brake system.

(Without brakes)

■ Tongue Weight

The load placed on the trailer hitch ball. (P. 179)

4RUNNER (U)_(OM35B18U)

178

4-1. Before driving

Weight limits ● The gross trailer weight must never exceed the TWR described in

the table. (P. 179)

● The gross combination weight must never exceed the GCWR

described in the table. (P. 179) ● The gross vehicle weight must never exceed the GVWR indi- cated on the Certification Label. ● The gross axle weight on each axle must never exceed the GAWR indicated on the Certifi- cation Label.

● If the gross trailer weight is over the unbraked TWR, trailer service

brakes are required.

● If the gross trailer weight is over 2000 lb. (907 kg), a sway control

device with sufficient capacity is required.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

179

GCWR, TWR and Unbraked TWR Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. ■ GCWR* and TWR*

Driving system

2WD 4WD

Trailer Weight

Rating

5000 lb. (2270 kg)

GCWR

11100 lb. (5035 kg) 11300 lb. (5125 kg)

■ Unbraked TWR* 1655 lb. (750 kg)

*: These models meet the tow-vehicle trailering requirement of SAE Interna-

tional per SAE J2807. Trailer Tongue Weight ● A recommended tongue weight varies in accordance with the types

of trailers or towing as described below.

● To ensure the recommended values shown below, the trailer must

be loaded by referring to the following instructions. • Tongue Weight

The gross trailer weight should be distributed so that the tongue weight is 9% to 11%. (Tongue weight /Gross trailer weight x 100
= 9% to 11%)

Gross trailer weight Tongue weight

The gross trailer weight, gross axle weight and tongue weight can be measured with platform scales found at a highway weigh- ing station, building supply company, trucking company, junk yard, etc.

4RUNNER (U)_(OM35B18U)

180

4-1. Before driving

Hitch Trailer hitch assemblies have different weight capacities. Toyota rec- ommends the use of Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight require-

ment of your vehicle.

● Follow the directions supplied by the hitch manufacturer. ● Lubricate the hitch ball with a light coating of grease. ● Remove the trailer hitch whenever you are not towing a trailer. After removing the hitch, seal any mounting hole in the vehicle body to prevent entry of any substances into the vehicle.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

181

Selecting trailer ball Use the correct trailer ball for your application.

Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer cou- pler. Most couplers are stamped with the required trailer ball size.

Trailer class

Typical trailer ball size

IV

II and III

2 5/16 in.

2 in.

1 7/8 in.

Shank length Protrudes beyond the bottom of the lock washer and nut by at least 2
threads. Shank diameter Matches the ball mount hole diameter size.

4RUNNER (U)_(OM35B18U)

182

4-1. Before driving

Positions for towing hitch receiver and hitch ball

Weight carrying ball position: 50.1 in. (1272 mm) Hitch receiver pin hole position: 43.7 in. (1109 mm)

Connecting trailer lights Use the wire harness stored in the rear end under body.

Please consult your dealer when installing trailer lights, as incorrect installation may cause damage to the vehicle’s lights. Please take care to comply with your state’s laws when installing trailer lights.

■Service connector for towing brake controller

Your vehicle is equipped with a service connector for the trailer brake controller as shown.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

183

Trailer towing tips Your vehicle will handle differently when towing a trailer. Help to avoid an accident, death or serious injury, keep the following in mind when towing: ● Speed limits for towing a trailer vary by state or province. Do not

exceed the posted towing speed limit.

● Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest. Instability of the towing vehicle-trailer combination (trailer sway) increases as speed increases. Exceeding speed limits may cause loss of control. ● Before starting out, check the trailer lights, tires and the vehicle-

trailer connections. Recheck after driving a short distance.

● Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle-trailer combination.

● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

● As stopping distance is increased when towing a trailer, vehicle-to vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

● Avoid sudden braking as you may skid, resulting in the trailer jack- knifing and a loss of vehicle control. This is especially true on wet or slippery surfaces.

4RUNNER (U)_(OM35B18U)

184

4-1. Before driving

● Avoid jerky starts or sudden acceleration. ● Avoid jerky steering and sharp turns, and slow down before making

turn.

● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a wider than normal turning radius.

● Slow down before making a turn, in cross winds, on wet or slippery

surfaces, etc. Increasing vehicle speed can destabilize the trailer.

● Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

● To maintain engine braking efficiency and charging system perfor- mance when using engine braking, do not put the transmission in D.

● Instability happens more frequently when descending steep or long downhill grades. Before descending, slow down and downshift. Do not make sudden downshifts while descending steep or long down- hill grades.

● Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

● Due to the added load of the trailer, your vehicle’s engine may over- heat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the engine coolant temperature gauge indicates overheating, immediately turn off the air conditioning (if in use), pull your vehicle off the road and stop in a safe spot. (P. 450)

4RUNNER (U)_(OM35B18U)

4-1. Before driving

185

● Always place wheel blocks under both the vehicle’s and the trailer’s wheels when parking. Apply the parking brake firmly, and put the transmission in P. Avoid parking on a slope, but if unavoidable, do so only after performing the following: Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle’s and trailer’s wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into P and turn off the engine.

● When restarting after parking on a slope:

With the transmission in P, start the engine. Be sure to keep the brake pedal pressed. Shift into a forward gear. If reversing, shift into R. Release the parking brake and brake pedal, and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

■Matching trailer ball height to trailer coupler height

No matter which class of tow hitch applies, for a more safe trailer hookup, the trailer ball setup must be the proper height for the coupler on the trailer.

Coupler Trailer ball

4RUNNER (U)_(OM35B18U)

186

4-1. Before driving

■Before towing

Check that the following conditions are met: ●Ensure that your vehicle’s tires are properly inflated. (P. 464) ●Trailer tires are inflated according to the trailer manufacturer’s recommen-

dation.

●All trailer lights work as required by law. ●All lights work each time you connect them. ●The trailer ball is set at the proper height for the coupler on the trailer. ●The trailer is level when it is hitched.

Do not drive if the trailer is not level, and check for improper tongue weight, overloading, worn suspension, or other possible causes.

●The trailer cargo is securely loaded. ●The rear view mirrors conform to all applicable federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for tow- ing purposes.

■Break-in schedule

If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km). After the vehicle has been driven for over 500 miles (800 km), you can start towing. However, for the next 500 miles (800 km), drive the vehicle at a speed of less than 45 mph (72 km/h) when towing a trailer, and avoid full throttle acceleration. ■Maintenance

●If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

●Retighten the fixing bolts of the towing ball and bracket after approximately

600 miles (1000 km) of trailer towing.

■If trailer sway occurs

One or more factors (crosswinds, passing vehicles, rough roads, etc.) can adversely affect handling of your vehicle and trailer, causing instability. ●If trailer swaying occurs:

• Firmly grip the steering wheel. Steer straight ahead.

Do not try to control trailer swaying by turning the steering wheel.

• Begin releasing the accelerator pedal immediately but very gradually to

reduce speed. Do not increase speed. Do not apply vehicle brakes.

If you make no extreme correction with the steering or brakes, your vehicle and trailer should stabilize. (if enabled, Trailer Sway Control can also help to stabilize the vehicle and trailer.)

4RUNNER (U)_(OM35B18U)

●After the trailer swaying has stopped:

4-1. Before driving

187

• Stop in a safe place. Get all occupants out of the vehicle. • Check the tires of the vehicle and the trailer. • Check the load in the trailer.

Make sure the load has not shifted. Make sure the tongue weight is appropriate, if possible.

• Check the load in the vehicle.

Make sure the vehicle is not overloaded after occupants get in.

If you cannot find any problems, the speed at which trailer swaying occurred is beyond the limit of your particular vehicle-trailer combination. Drive at a lower speed to prevent instability. Remember that swaying of the towing vehicle-trailer increases as speed increases.

CAUTION

■Trailer towing precautions

To tow a trailer safely, use extreme care and drive the vehicle in accordance with the trailer’s characteristics and operating conditions. Failure to do so could cause an accident resulting in death or serious injury. Vehicle stability and braking performance are affected by trailer stability, brake setting and performance, and the hitch. Your vehicle will handle differently when towing a trailer.

■To avoid accident or injury

●Do not exceed the TWR, unbraked TWR, GCWR, GVWR or GAWR. ●If the gross trailer weight is over 2000 lb. (907 kg), a sway control device

with sufficient capacity is required.

●Adjust the tongue weight within the appropriate range. Place heavier loads

as close to the trailer axle as possible.

●Do not exceed 65 mph (104 km/h), the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest. Slow down sufficiently before making a turn, in cross winds, on wet or slippery surface, etc. to help avoid an accident. If you experience a vehicle-trailer instability from reducing a certain speed, slow down and make sure you keep your vehicle speed under the speed of which you experience the instability.

●Do not make jerky, abrupt or sharp turns.

4RUNNER (U)_(OM35B18U)

188

4-1. Before driving

CAUTION

●Do not apply the brakes suddenly as you may skid, resulting in jackknifing and loss of vehicle control. This is especially true on wet or slippery sur- faces.

●Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue weight capacities.

●Do not use cruise control when towing. ●Slow down and downshift before descending steep or long downhill grades. Do not make sudden downshifts while descending steep or long downhill grades.

●Vehicle-trailer instability is more likely on steep long downhills. Before descending steep or long downhill grades, slow down and downshift. Do not make sudden downshifts when descending steep or long downhill grades. Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

■Hitch

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be physically capable of towing a higher weight, the operator must determine the maximum weight rating of the particular hitch assembly and never exceed the maximum weight rating specified for the trailer-hitch. Exceeding the maximum weight rating set by the trailer-hitch manufacturer can cause an accident resulting in death or serious personal injuries.

■When towing a trailer

Toyota recommends trailers with brakes that conform to any applicable fed- eral and state/provincial regulations. ●If the gross trailer weight exceeds unbraked TWR, trailer brakes are required. Toyota recommends trailers with brakes that conform to all appli- cable federal and state/provincial regulations.

●Never tap into your vehicle’s hydraulic system, as this will lower the vehi-

cle’s braking effectiveness.

●Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

4RUNNER (U)_(OM35B18U)

4-1. Before driving

189

NOTICE

■When installing a trailer hitch

Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage.

■Do not directly splice trailer lights

Do not directly splice trailer lights. Directly splicing trailer lights may damage your vehicle’s electrical system and cause a malfunction.

4RUNNER (U)_(OM35B18U)

190

4-1. Before driving

Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with the four wheels on the ground.

4RUNNER (U)_(OM35B18U)

4

4-2. Driving procedures

191

Engine (ignition) switch (vehicles without a smart key system)

Starting the engine

Check that the parking brake is set. Check that the shift lever is set in P. Firmly depress the brake pedal. Turn the engine switch to the “START” position to start the engine.

Changing the engine switch positions

“LOCK” The steering wheel is locked and the key can be removed. (The key can be removed only when the shift lever is in P.) “ACC” Some electrical components such as the audio system can be used.

“ON” All electrical components can be used. “START” For starting the engine.

4RUNNER (U)_(OM35B18U)

192

4-2. Driving procedures

■Turning the key from “ACC” to “LOCK”

Shift the shift lever to P. Push in the key and turn to the “LOCK” position.

■If the engine does not start

The engine immobilizer system may not have been deactivated. (P. 70) Contact your Toyota dealer.

■When the steering lock cannot be released

When starting the engine, the engine switch may seem stuck in the “LOCK” position. To free it, turn the key while turn- ing the steering wheel slightly left and right.

■Key reminder function

A buzzer sounds if the driver’s door is opened, while the engine switch is in the “LOCK” or “ACC” position to remind you to remove the key.

4RUNNER (U)_(OM35B18U)

4-2. Driving procedures

193

CAUTION

■When starting the engine

Always start the engine while sitting in the driver's seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

■Caution when driving

Do not turn the engine switch to the “LOCK” position while driving. If, in an emergency, you must turn the engine off while the vehicle is moving, turn the engine switch only to the “ACC” position to stop the engine. An accident may result if the engine is stopped while driving.

NOTICE

■To prevent battery discharge

Do not leave the engine switch in the “ACC” or “ON” position for long peri- ods of time without the engine running.

■When starting the engine

●Do not crank the engine for more than 30 seconds at a time. This may

overheat the starter and wiring systems.

●Do not race a cold engine. ●If the engine becomes difficult to start or stalls frequently, have the engine

checked immediately.

4RUNNER (U)_(OM35B18U)

194

4-2. Driving procedures

Engine (ignition) switch (vehicles with a smart key system)

Performing the following operations when carrying the elec- tronic key on your person starts the engine or changes engine switch modes.

Starting the engine

Check that the parking brake is set. Check that the shift lever is set in P. Firmly depress the brake pedal. The engine switch indicator will turn green. If the indicator does not turn green, the engine cannot be started. Press the engine switch. The engine will crank until it starts or for up to 30 seconds, whichever is less. Continue depressing the brake pedal until the engine is completely started. The engine can be started from any engine switch mode.

4RUNNER (U)_(OM35B18U)

4-2. Driving procedures

195

Stopping the engine

Stop the vehicle. Shift the shift lever to P. Set the parking brake. (P. 203) Press the engine switch. Release the brake pedal and check that the indicator on the engine switch is off.

Changing engine switch modes Modes can be changed by pressing the engine switch with brake pedal released. (The mode changes each time the switch is pressed.)

Off* The emergency flashers can be used. The engine switch indicator turns amber. ACCESSORY mode Some electrical components such as the audio system can be used. The engine switch indicator turns amber. IGNITION ON mode All electrical components can be used. *: If the shift lever is in a position other than P when turning off the engine, the engine switch will be turned to ACCESSORY mode, not to off.

4RUNNER (U)_(OM35B18U)

196

4-2. Driving procedures

When stopping the engine with the shift lever in a position other than P If the engine is stopped with the shift lever in a position other than P, the engine switch will not be turned off but instead be turned to ACCESSORY mode. Perform the following procedure to turn the switch off:

Check that the parking brake is set. Shift the shift lever to P. Check that the indicator on the engine switch is illuminated in amber and then press the engine switch once. Check that the indicator on the engine switch is off.

■Auto power off function

If the vehicle is left in ACCESSORY mode for more than 20 minutes or IGNI- TION ON mode (the engine is not running) for more than an hour with the shift lever in P, the engine switch will automatically turn off. However, this function cannot entirely prevent battery discharge. Do not leave the vehicle with the engine switch in ACCESSORY or IGNITION ON mode for long peri- ods of time when the engine is not running.

■Electronic key battery depletion

P. 93

■Conditions affecting operation

P. 106

■Notes for the entry function

P. 107

■If the engine does not start

The engine immobilizer system may not have been deactivated. (P. 70) Contact your Toyota dealer.

■Steering lock

After turning the engine switch off and opening and closing the doors, the steering wheel will be locked due to the steering lock function. Operating the engine switch again automatically cancels the steering lock.

4RUNNER (U)_(OM35B18U)

4

4-2. Driving procedures

197

■When the steering lock cannot be released

The green indicator light on the engine switch will flash. Press the engine switch again while turning the steering wheel left and right.

■Steering lock motor overheating prevention

To prevent the steering lock motor from overheating, the motor may be sus- pended if the engine is turned on and off repeatedly in a short period of time. In this case, refrain from operating the engine. After about 10 seconds, the steering lock motor will resume functioning.

■When the engine switch indicator flashes in amber

The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately.

■If the electronic key battery is depleted

P. 377

■Operation of the engine switch

When operating the engine switch, one short, firm press is enough. If the switch is pressed improperly, the engine may not start or the engine switch mode may not change. It is not necessary to press and hold the switch.

4RUNNER (U)_(OM35B18U)

198

4-2. Driving procedures

CAUTION

■When starting the engine

Always start the engine while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

■Caution while driving

If engine failure occurs while the vehicle is moving, do not lock or open the doors until the vehicle reaches a safe and complete stop. Activation of the steering lock in this circumstance may lead to an accident, resulting in death or serious injury.

■Stopping the engine in an emergency

If you want to stop the engine in an emergency while driving the vehicle, press and hold the engine switch for more than 2 seconds, or press it briefly 3 times or more in succession. (P. 401) However, do not touch the engine switch while driving except in an emer- gency. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so.

NOTICE

■To prevent battery discharge

Do not leave the engine switch in ACCESSORY or IGNITION ON mode for long periods of time without the engine running.

■When starting the engine ●Do not race a cold engine. ●If the engine becomes difficult to start or stalls frequently, have your vehi-

cle checked by your Toyota dealer immediately.

4RUNNER (U)_(OM35B18U)

4-2. Driving procedures

199

Automatic transmission

Shifting the shift lever

 Vehicles without a smart key system

While the engine switch is in the “ON” position, move the shift lever with the brake pedal depressed. When shifting the shift lever between P and D, make sure that the vehicle is completely stopped.  Vehicles with a smart key system

While the engine switch is in IGNITION ON mode, move the shift lever with the brake pedal depressed. When shifting the shift lever between P and D, make sure that the vehicle is completely stopped.

4RUNNER (U)_(OM35B18U)

200

4-2. Driving procedures

Shift position purpose

Shift position

Objective or function

Parking the vehicle/starting the engine

Reversing Neutral

Normal driving*1

S mode driving*2 (P. 200)

*1: To improve fuel efficiency and reduce noises, set the shift lever in the D

position for normal driving.

*2: Selecting shift ranges using S mode restricts the upper limit of the possible gear ranges, controls engine braking forces, and prevents unnecessary upshifting

Changing shift ranges in S mode When the shift lever is in the S position, the shift lever can be oper- ated as follows:

Upshifting Downshifting

The initial shift range in S mode is set automatically to “4” according to vehicle speed. However, the initial shift range may be set to “3” if AI- SHIFT has operated while the shift lever was in the D position. (P. 201) ■ Shift ranges and their functions

You can choose from 5 levels of engine braking force. A lower shift range will provide greater engine braking force than a higher shift range, and the engine speed will also increase.

4RUNNER (U)_(OM35B18U)

4

4-2. Driving procedures

201

■S mode

When the shift range is “3” or lower, holding the shift lever toward “+” sets the shift range to “5”.

■AI-SHIFT

AI-SHIFT automatically selects the optimal gear according to driver perfor- mance and driving conditions. AI-SHIFT automatically operates when the shift lever is in the D position. (Shifting the shift lever to the S position or paddle shifting cancels the func- tion.) The engine speed may remain high after releasing the accelerator pedal. This does not indicate a malfunction.

■When driving with cruise control system

Engine braking will not occur in S mode, even when downshifting to “4”. (P. 221)

■If the shift lever cannot be shifted from P

P. 443

■If the “S” indicator does not come on even after shifting the shift lever to

This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the transmission will operate in the same manner as when the shift lever is in D.)

■Downshift restriction warning buzzer (S mode)

To help ensure safety and driving performance, downshifting operation may sometimes be restricted. In some circumstances, downshifting may not be possible even when the shift lever is operated. (A buzzer will sound twice.)

CAUTION

■When driving on slippery road surfaces

Be careful of downshifting and sudden acceleration, as this could result in the vehicle skidding to the side or spinning.

4RUNNER (U)_(OM35B18U)

202

4-2. Driving procedures

Turn signal lever

Operating instructions The lever will return to its original position after operation.

Right turn Lane change to the right (push and hold the lever partway) The right hand signals will flash until you release the lever. Lane change to the left (push and hold the lever partway) The left hand signals will flash until you release the lever. Left turn

■Turn signals can be operated when  Vehicles without a smart key system The engine switch is in the “ON” position.  Vehicles with a smart key system The engine switch is in IGNITION ON mode.

■If the indicator flashes faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

4RUNNER (U)_(OM35B18U)

Parking brake

To set the parking brake, fully depress the parking brake pedal with your left foot while depress- ing the brake pedal with your right foot. (Depressing releases the parking brake.)

the pedal again

■Usage in winter time

P. 269

NOTICE

■Before driving

4-2. Driving procedures

203

U.S.A. Canada

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

4RUNNER (U)_(OM35B18U)

204

4-3. Operating the lights and wipers

Headlight switch

The headlights can be operated manually or automatically.

Operating instructions Turning the end of the lever turns on the lights as follows:  Type A