2015 Toyota 4runner Owners Manual

3-3. Adjusting the seats

■ Returning the third row seats

As the seat cushions cannot be pulled forward from outside, this operation can only be performed from inside.

Raise the seatbacks to their original positions. Make sure securely.

they are

locked

Pull the seat cushions for- ward.

Raise the head restraints.

4RUNNER (U)_(OM35B18U)

3

3-3. Adjusting the seats

131

CAUTION

■When folding the rear seatbacks down

Observe the following precautions. Failure to do so may result in death or serious injury. ●Do not fold the seatbacks down while driving. ●Stop the vehicle on level ground, set the parking brake and shift the shift

lever to P.

●Do not allow anyone to sit on a folded seatback or in the luggage compart-

ment while driving.

●Do not allow children to enter the luggage compartment.

■Seat adjustment

●To reduce the risk of sliding under the lap belt during a collision, do not

recline the seat more than necessary. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen, or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident. Adjustments should not be made while driving as the seat may unexpect- edly move and cause the driver to lose control of the vehicle.

●Take care when adjusting the seat position to ensure that other passen-

gers are not injured by the moving seat.

●Do not put your hands under the seat or near the moving parts to avoid

injury. Fingers or hands may become jammed in the seat mechanism.

■After returning the rear seatback to the upright position

Observe the following precautions. Failure to do so may result in death or serious injury. ●Make sure the seatback is securely locked by pushing it forward and rear-

ward on the top.

●Check that the seat belts are not twisted or caught in the seatback.

NOTICE

■Stowing the seat belts

The seat belts and the buckles must be stowed before you fold down the rear seatbacks.

4RUNNER (U)_(OM35B18U)

3-3. Adjusting the seats

132
Driving position memory

This feature automatically adjusts the driver’s seat to suit your preferences.

Driving position memory Your preferred driving position (the position of the driver’s seat) can be recorded and recalled by pressing a button. Two different driving positions can be recorded into memory. ■ Recording procedure

Check that the shift lever is in P. Turn the engine switch to IGNITION ON mode. Adjust the driver’s seat to the desired positions. While pressing the “SET” but- ton, or within 3 seconds after the “SET” button is pressed, press button “1” or “2” until the buzzer sounds. If the selected button has already been previously recorded position will be overwrit- ten.

preset,

the

Recall procedure

Check that the shift lever is in P. Turn the engine switch to IGNITION ON mode. Press one of the buttons for the driving position you want to recall until the buzzer sounds.

: If equipped

4RUNNER (U)_(OM35B18U)

3

3-3. Adjusting the seats

133

■To stop the position recall operation part-way through

Perform any of the following: ●Press the “SET” button. ●Press button “1” or “2”. ●Operate any of the seat adjustment switches (only cancels seat position

recall).

■Seat positions that can be memorized (P. 119)

All adjusted positions can be recorded.

■Operating the driving position memory after turning the engine switch

off Recorded seat positions can be activated up to 180 seconds after the driver’s door is opened and another 60 seconds after it is closed again.

■In order to correctly use the driving position memory function

If a seat position is already in the furthest possible position and the seat is operated in the same direction, the recorded position may be slightly different when it is recalled.

Memory recall function Each electronic key can be registered to recall your preferred driving position. ■ Registering procedure

Record your driving position to button “1” or “2” before performing the following: Carry only the key you want to register, and then close the driver’s door. If 2 or more keys are in the vehicle, the driving position cannot be recorded properly.

Check that the shift lever is in P. Turn the engine switch to IGNITION ON mode. Recall the driving position that you want to record.

4RUNNER (U)_(OM35B18U)

134

3-3. Adjusting the seats

While pressing the recalled button, press and hold the door lock switch (either lock or unlock) until the buzzer sounds. If the button could not be regis- tered, the buzzer sounds contin- uously for approximately 3
seconds.

■ Recall procedure

Carry the electronic key that has been registered to the driving position, and then unlock and open the driver’s door using the smart system or wireless remote control.

The driving position will move to the recorded position. If the driving position is in a position that has already been recorded, the seat will not move.

■ Cancelation procedure

Carry only the key you want to cancel and then close the driver’s door. If 2 or more keys are in the vehicle, the driving position cannot be canceled properly.

Turn the engine switch to IGNITION ON mode. While pressing the “SET” button, press and hold the door lock switch (either lock or unlock) until the buzzer sounds twice. If the button could not be canceled, the buzzer sounds continuously for approximately 3 seconds.

■Recalling the driving position using the memory recall function

●Different driving positions can be registered for each electronic key. There- fore, the driving position that is recalled may be different depending on the key being carried.

●If a door other than the driver’s door is unlocked with the smart system, the driving position cannot be recalled. In this case, press the driving position button which has been set.

■Customization

The unlock door settings of the memory recall function can be customized. (Customizable features: P. 481)

4RUNNER (U)_(OM35B18U)

3-3. Adjusting the seats

135

CAUTION

■Seat adjustment caution

Take care during seat adjustment so that the seat does not strike the rear passenger or squeeze your body against the steering wheel.

4RUNNER (U)_(OM35B18U)

136

3-3. Adjusting the seats

Head restraints

Head restraints are provided for all seats.

Front seats Vertical adjustment

Up Pull the head restraints up. Down Push the head restraint down while pressing the lock release button.

Second seats Vertical adjustment

Up Pull the head restraints up. Down Push the head restraint down while pressing the lock release button.

Folding the head restraints (vehi- cle without third row seats)

To use Lift up the head restraint until it locks. To fold Pull the head restraint lock release lever to fold the head restraint.

Lock release button

Lock release button

4RUNNER (U)_(OM35B18U)

3-3. Adjusting the seats

137

Third seats (vehicle with third row seats)

To use Lift up the head restraint until it locks. To fold Pull the strap to fold the head restraint.

■Removing the head restraints (except third row seats)

Pull the head restraint up while pressing the lock release button.

Lock release button

■Installing the head restraints (except third row seats)

Align the head restraint with the installa- tion holes and push it down to the lock position. Press and hold the lock release button when lowering the head restraint.

Lock release button

■Adjusting the height of the head restraints (except third row seats)

Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.

■Adjusting the second center seat head restraint

Always raise the head restraint one level from the stowed position when using.

4RUNNER (U)_(OM35B18U)

138

3-3. Adjusting the seats

CAUTION

■Head restraint precautions

Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury. ●Use the head restraints designed for each respective seat. ●Adjust the head restraints to the correct position at all times. ●After adjusting the head restraints, push down on them and make sure

they are locked in position.

●Do not drive with the head restraints removed.

4RUNNER (U)_(OM35B18U)

3-4. Adjusting the steering wheel and mirrors

139

Steering wheel

The steering wheel can be adjusted to a comfortable position.

Adjustment procedure

Hold the steering wheel and push the lever down.

Adjust to the ideal position by moving the steering wheel hori- zontally and vertically. After adjustment, pull the lever up to secure the steering wheel.

Horn To sound the horn, press on or close to the

mark.

4RUNNER (U)_(OM35B18U)

140

3-4. Adjusting the steering wheel and mirrors

CAUTION

■Caution while driving

Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury.

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident, and resulting in death or serious injury. Also, the horn may not sound if the steering wheel is not securely locked.

4RUNNER (U)_(OM35B18U)

3-4. Adjusting the steering wheel and mirrors

141

Inside rear view mirror

The rear view mirror’s position can be adjusted to enable suffi- cient confirmation of the rear view.

Adjusting the height of rear view mirror The height of the rear view mirror can be adjusted to suit your driving posture. Adjust the height of the rear view mirror by moving it up and down.

Anti-glare function  Manual anti-glare inside rear view mirror

Normal position Anti-glare position

4RUNNER (U)_(OM35B18U)

142

3-4. Adjusting the steering wheel and mirrors

 Auto anti-glare inside rear view mirror Responding to the level of brightness of the headlights of vehicles behind, the reflected light is automatically reduced. Changing automatic anti-glare function mode ON/OFF When the automatic anti-glare function is in on mode, the indica- tor illuminates. Vehicles without a smart key sys- tem: The function will set to on mode each time the engine switch is turned to the “ON” position. Pressing the button turns the func- tion to off mode. (The indicator also turns off.) Vehicles with a smart key system: The function will set to on mode each time the engine switch is turned to IGNITION ON mode. Pressing the button turns the func- tion to off mode. (The indicator also turns off.)

Indicator

■To prevent sensor error (auto anti-glare type)

To ensure that the sensors operate prop- erly, do not touch or cover them.

CAUTION

Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and cause an accident, resulting in death or serious injury.

4RUNNER (U)_(OM35B18U)

3

3-4. Adjusting the steering wheel and mirrors

143

Outside rear view mirrors

Adjustment procedure

To select a mirror to adjust, press the switch.

Left Right

To adjust the mirror, press the switch.

Up Right Down Left

Folding the mirrors Push the mirror back in the direc- tion of the vehicle’s rear.

4RUNNER (U)_(OM35B18U)

144

3-4. Adjusting the steering wheel and mirrors

■Mirror angle can be adjusted when  Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position.  Vehicles with a smart key system The engine switch is in ACCESSORY or IGNITION ON mode.

■When the mirrors are fogged up

The outside rear view mirrors can be cleared using the mirror defoggers. Turn on the rear window defogger to turn on the outside rear view mirror defog- gers. (P. 280, 286)

CAUTION

■Important points while driving

Observe the following precautions while driving. Failure to do so may result in loss of control of the vehicle and cause an accident, resulting in death or serious injury. ●Do not adjust the mirrors while driving. ●Do not drive with the mirrors folded. ●Both the driver and passenger side mirrors must be extended and properly

adjusted before driving. ■When a mirror is moving

To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.

■When the mirror defoggers are operating

Do not touch the rear view mirror surfaces, as they can become very hot and burn you.

4RUNNER (U)_(OM35B18U)

3

3-5. Opening, closing the windows and moon roof

145

Power windows

Opening and closing procedures The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows:

Closing One-touch closing* Opening One-touch opening*

*:To stop the window partway, oper- ate the switch in the opposite direc- tion.

Window lock switch Press the switch to lock the pas- senger window switches and back window switch.

Use this switch to prevent children from accidentally opening or clos- ing a passenger window.

4RUNNER (U)_(OM35B18U)

146

3-5. Opening, closing the windows and moon roof

■The power windows can be operated when

 Vehicles without a smart key system The engine switch is in the “ACC” or “ON” position.  Vehicles with a smart key system The engine switch is in IGNITION ON mode.

■Operating the power windows after turning the engine off

 Vehicles without a smart key system The power windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They can- not, however, be operated once either front door is opened.  Vehicles with a smart key system The power windows can be operated for approximately 45 seconds even after the engine switch is turned to ACCESSORY mode or turned off. They cannot, however, be operated once either front door is opened.

■Jam protection function

If an object becomes caught between the window and the window frame, win- dow travel is stopped and the window is opened slightly.

■When the power window does not close normally

If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the relevant door. ●Vehicles without a smart key system: After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch closing position while the engine switch is turned to the “ON” position.

●Vehicles with a smart key system: After stopping the vehicle, the window can be closed by holding the power window switch in the one-touch closing position while the engine switch is turned to IGNITION ON mode.

●If the window still cannot be closed even by carrying out the operation as explained above, initialize the function by performing the following proce- dure.

Hold the power window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the window has closed. Hold the power window switch in the one-touch opening position. Con- tinue holding the switch for a further 2 seconds after the window has opened completely. Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the win- dow has closed.

If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after perform- ing the above procedure correctly, have the vehicle inspected by your Toyota dealer.

4RUNNER (U)_(OM35B18U)

3

3-5. Opening, closing the windows and moon roof

147

■Door lock linked window operation

●The power windows can be opened and closed using the key or mechanical key.* (P. 97, 445) ●The power windows can be opened using the wireless remote control.* (P. 96) *: These settings must be customized at your Toyota dealer.

■Customization

Settings (e.g. key linked operation) can be changed. (Customizable features P. 481)

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■Closing the windows

●The driver is responsible for all the power window operations, including the operation for the passengers. In order to prevent accidental operation, especially by a child, do not let a child operate the power windows. It is possible for children and other passengers to have body parts caught in the power window. Also, when riding with a child, it is recommended to use the window lock switch. (P. 145)

●Check to make sure that all passengers do not have any part of their body

in a position where it could be caught when a window is being operated.

●When using the key or mechanical key and operating the power windows, operate the power window after checking to make sure that there is no possibility of any passenger having any of their body parts caught in the window. Also do not let a child operate window by the key or mechanical key. It is possible for children and other passengers to get caught in the power window.

●When exiting the vehicle, turn the engine switch off, carry the key and exit the vehicle along with the child. There may be accidental operation, due to mischief, etc., that may possibly lead to an accident.

■Jam protection function

●Never use any part of your body to intentionally activate the jam protection

function.

●The jam protection function may not work if something gets caught just

before the window fully closes.

4RUNNER (U)_(OM35B18U)

148

3-5. Opening, closing the windows and moon roof

Power back window

The power back window can be opened and closed using the switch or key.

Opening and closing procedures  From inside the vehicle

Closing One-touch closing* Opening One-touch opening*

*: To stop the window partway, operate the switch in the oppo- site direction.

 From outside the vehicle (vehicles without a smart key system)

Opening Closing Turn the key fully and hold it.

4RUNNER (U)_(OM35B18U)

3

3-5. Opening, closing the windows and moon roof

149

 From outside the vehicle (vehicles with a smart key system)

Opening (push and hold) Closing (push and hold) This operation can only be per- formed when the electronic key is within the detection range.

■The power back window can be operated from inside the vehicle when

 Vehicles without a smart key system The engine switch is in the “ON” position.  Vehicles with a smart key system The engine switch is in IGNITION ON mode. ●The power back window can be opened when the rear window wiper is

working, but the wiper stops working until the window is closed again. If the power back window is not fully closed, the rear window wiper, washer, and defogger will not work.

●If the back door is not fully closed, the power back window cannot be opened using the switch located in the cabin. (It is still possible to close the window.)

●If the back door is opened while the power back window is opening or clos-

ing, window operation will stop.

■The power back window can be operated from outside the vehicle when

(vehicles with a smart key system) ●The engine switch is off. ●The back door is closed.

4RUNNER (U)_(OM35B18U)

150

3-5. Opening, closing the windows and moon roof

■Operating the power back window from inside the vehicle after turning

the engine off  Vehicles without a smart key system The power back window can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. It cannot, however, be operated once either front door is opened.  Vehicles with a smart key system The power back window can be operated for approximately 45 seconds even after the engine switch is turned to ACCESSORY mode or turned off. It can- not, however, be operated once either front door is opened.

■Jam protection function

If an object becomes caught between the window and the window frame, win- dow travel is stopped and the window is opened slightly.

■When the power back window does not close normally

If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power back window switch. ●Vehicles without a smart key system: After stopping the vehicle, the window can be closed by holding the power back window switch in the one-touch closing position while the engine switch is turned to the “ON” position.

●Vehicles with a smart key system: After stopping the vehicle, the window can be closed by holding the power back window switch in the one-touch closing position while the engine switch is turned to IGNITION ON mode.

●If the window still cannot be closed even by carrying out the operation explained above, initialize the function by performing the following proce- dure.

Hold the power back window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the window has closed. Hold the power back window switch in the one-touch opening position. Continue holding the switch for a further 2 seconds after the window has opened completely. Hold the power back window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.

If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after perform- ing the above procedure correctly, have the vehicle inspected by your Toyota dealer.

■Customization

Settings (e.g. linked operation) can be changed. (Customizable features P. 481)

4RUNNER (U)_(OM35B18U)

3

3-5. Opening, closing the windows and moon roof

151

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■Caution while driving

Keep the back door and back window closed while driving. If the back door or the back window is left open, the back door may hit nearby objects while driving or luggage may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri- ous health hazard. Make sure to close the back door and back window before driving.

■Closing the power back window

●The driver is responsible for power back window opening and closing

operations. In order to prevent accidental operation, especially by a child, do not let a child operate the power back window. It is possible for children and other passengers to have body parts caught in the power back window.

●Check to make sure that all passengers do not have any part of their body

in a position where it could be caught when a window is being operated.

●When using the wireless remote control or key and operating the power back window, operate the power back window after checking to make sure that there is no possibility of any passenger having any of their body parts caught in the power back window. Also, do not let a child operate power back window by the wireless remote control or key. It is possible for chil- dren and other passengers to get caught in the power back window.

●When exiting the vehicle, turn the engine switch off, carry the key and exit the vehicle along with the child. There may be accidental operation, due to mischief, etc., that may possibly lead to an accident.

■Jam protection function

●Never use any part of your body to intentionally activate the jam protection

function.

●The jam protection function may not work if something gets caught just

before the window fully closes.

4RUNNER (U)_(OM35B18U)

3-5. Opening, closing the windows and moon roof

152
Moon roof

Use the overhead switches to open and close the moon roof and tilt it up and down.

Opening and closing

Opens the moon roof* The moon roof stops slightly before the fully open position to reduce wind noise. Press the switch again to fully open the moon roof. Closes the moon roof*

*: Lightly press either way of the moon roof switch to stop the moon roof partway.

Tilting up and down

Tilts the moon roof up* Tilts the moon roof down*

*: Lightly press either way of the moon roof switch to stop the moon roof partway.

: If equipped

4RUNNER (U)_(OM35B18U)

3-5. Opening, closing the windows and moon roof

153

■The moon roof can be operated when

 Vehicles without a smart key system The engine switch is in the “ON” position.  Vehicles with a smart key system The engine switch is in IGNITION ON mode.

■Operating the moon roof after turning the engine off

 Vehicles without a smart key system The moon roof can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They cannot, how- ever, be operated once either front door is opened.  Vehicles with a smart key system The moon roof can be operated for approximately 45 seconds after the engine switch is turned to ACCESSORY mode or turned off. It cannot, how- ever, be operated once either front door is opened.

■Jam protection function

If an object is detected between the moon roof and the frame while the moon roof is closing or tilting down, travel is stopped and the moon roof opens slightly.

■To reduce moon roof wind noise

When the moon roof is opened automatically, it will stop slightly before the fully open position. Driving with the moon roof in this position can help reduce wind noise. ■Sunshade

The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.

4RUNNER (U)_(OM35B18U)

154

3-5. Opening, closing the windows and moon roof

■When the moon roof does not close normally

Perform the following procedure: ●If the moon roof closes but then re-opens slightly

Stop the vehicle. Press and hold the “SLIDE (open/close)” switch in the close position.*1
The moon roof will close, reopen and pause for approximately 10 sec- onds.*2 Then it will close again, tilt up and pause for approximately 1 sec- ond. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.

●If the moon roof tilts down but then tilts back up

Stop the vehicle. Press and hold the “UP” switch*1 until the moon roof moves into the tilt up position and stops. Release the “UP” switch once and then press and hold the “UP” switch again.*1
The moon roof will pause for approximately 10 seconds in the tilt up posi- tion.*2 Then it will adjust slightly and pause for approximately 1 second. Finally, it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.

*1: If the switch is released at the incorrect time, the procedure will have to

be performed again from the beginning.

*2: If the switch is released after the above mentioned 10 second pause, automatic operation will be disabled. In that case, press and hold the “UP” or “DOWN” switch, and the moon roof will tilt up and pause for approximately 1 second. Then it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.

If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer.

■Moon roof open reminder function

An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the engine switch off.

■Door lock linked moon roof operation ●The moon roof can be opened and closed using the key or mechanical key.* (P. 97, 445) ●The moon roof can be opened using the wireless remote control.* (P. 96) *: These settings must be customized at your Toyota dealer.

4RUNNER (U)_(OM35B18U)

3

3-5. Opening, closing the windows and moon roof

155

■Customization that can be configured at Toyota dealer

Settings (e.g. key linked operation) can be changed. (Customizable features P. 481)

CAUTION

Observe the following precautions. Failure to do so may cause death or serious injury. ■Opening the moon roof

●Do not allow any passengers to put their hands or heads outside the vehi-

cle while it is moving.

●Do not sit on top of the moon roof.

■Closing the moon roof

●The driver is responsible for moon roof opening and closing operations.

In order to prevent accidental operation, especially by a child, do not let a child operate the moon roof. It is possible for children and other passen- gers to have body parts caught in the moon roof.

●Check to make sure that all passengers do not have any part of their body in a position where it could be caught when the moon roof is being oper- ated.

●When using the key or mechanical key and operating the moon roof, oper- ate the moon roof after checking to make sure that there is no possibility of any passenger having any of their body parts caught in the moon roof. Also, do not let a child operate moon roof by the key or mechanical key. It is possible for children and other passengers to get caught in the moon roof.

●When exiting the vehicle, turn the engine switch off, carry the key and exit the vehicle along with the child. There may be accidental operation, due to mischief, etc., that may possibly lead to an accident.

■Jam protection function

●Never use any part of your body to intentionally activate the jam protection

function.

●The jam protection function may not work if something gets caught just

before the moon roof fully closes.

4RUNNER (U)_(OM35B18U)

156

3-5. Opening, closing the windows and moon roof

4RUNNER (U)_(OM35B18U)

Driving

157

4-1. Before driving

Driving the vehicle............. 158
Cargo and luggage ........... 168
Vehicle load limits ............. 173
Trailer towing..................... 174
Dinghy towing ................... 190

4-2. Driving procedures

Engine (ignition) switch (vehicles without a smart key system)........... 191
Engine (ignition) switch (vehicles with a smart key system)........... 194
Automatic transmission..... 199
Turn signal lever................ 202
Parking brake.................... 203

4-3. Operating the lights and

wipers Headlight switch................ 204
Fog light switch ................. 210
Windshield wipers and washer ............................ 212
Rear window wiper and washer ............................ 215

4-4. Refueling

Opening the fuel tank cap .................................. 218

4-5. Using the driving support systems Cruise control.................... 221
Intuitive parking assist....... 225
Four-wheel drive system (part-time 4WD models) ........................... 231
Four-wheel drive system (full-time 4WD models) ........................... 235
Active traction control system ............................ 239
AUTO LSD system............ 241
Rear differential lock system ............................ 243
Downhill assist control system ............................ 246
Crawl Control .................... 249
Multi-terrain Select ............ 252
Driving assist systems ...... 259

4-6. Driving tips

Winter driving tips ............. 268
Off-road precautions ......... 272

4RUNNER (U)_(OM35B18U)

158

4-1. Before driving

Driving the vehicle

The following procedures should be observed to ensure safe driving:

Starting the engine P. 194
Driving

With the brake pedal depressed, shift the shift lever to D. (P. 199) Release the parking brake. (P. 203) Gradually release the brake pedal and gently depress the accelera- tor pedal to accelerate the vehicle.

Stopping

With the shift lever in D, depress the brake pedal until the vehicle comes to a stop. If necessary, set the parking brake. If the vehicle is to be stopped for an extended period of time, shift the shift lever to P or N. (P. 199)

Parking the vehicle

With the shift lever in D, depress the brake pedal. Set the parking brake. (P. 203) Shift the shift lever to P. (P. 199) If parking on a hill, block the wheels as needed. Vehicles without a smart key system: Turn the engine switch to the “LOCK” position to stop the engine. Vehicles with a smart key system: Press the engine switch to stop the engine. Lock the door, making sure that you have the key on your person.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

159

Starting off on a steep uphill

Make sure that the parking brake is set and shift the shift lever to D. Gently depress the accelerator pedal. Release the parking brake.

■Driving in the rain

●Drive carefully when it is raining, because visibility will be reduced, the win-

dows may become fogged-up, and the road will be slippery.

●Drive carefully when it starts to rain, because the road surface will be espe-

cially slippery.

●Refrain from driving at high speeds in the rain, as there may be a layer of water between the tires and the road surface, preventing the steering and brakes from operating properly.

■Engine speed while driving

In the following conditions, the engine speed may become high while driving. This is due to automatic up-shifting control or down-shifting implementation to meet driving conditions. It does not indicate sudden acceleration. ●The vehicle is judged to be driving uphill or downhill ●When the accelerator pedal is released

■Breaking in your new Toyota

To extend the life of the vehicle, observing the following precautions is recom- mended: ●For the first 200 miles (300 km):

Avoid sudden stops.

●For the first 500 miles (800 km):

Do not tow a trailer.

●For the first 1000 miles (1600 km):

• Do not drive at extremely high speeds. • Avoid sudden acceleration. • Do not drive continuously in low gears. • Do not drive at a constant speed for extended periods.

4RUNNER (U)_(OM35B18U)

160

4-1. Before driving

■Drum-in-disc type parking brake system

Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or whenever the parking brake shoes and/or drum are replaced. Have your Toyota dealer per- form the bedding down operation.

■Operating your vehicle in a foreign country

Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (P. 466) ■When turning off the engine

The emission system operating sounds may continue for a short time after the engine is turned off. This is not a malfunction, and helps to ensure optimal performance of the emission system.

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■When starting the vehicle

Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.

■When driving the vehicle

●Do not drive if you are unfamiliar with the location of the brake and accel-

erator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake

pedal will result in sudden acceleration that may lead to an accident.

• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly. This allows you to depress the brake and accelera- tor pedals properly.

• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.

●Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. These hot parts may cause a fire if there is any flammable material nearby.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

161

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■When driving the vehicle

●During normal driving, do not turn off the engine. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so. However, in the event of an emergency, such as if it becomes impossible to stop the vehicle in the normal way: P. 401

●Use engine braking (downshift) to maintain a safe speed when driving

down a steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (P. 199)

●Do not adjust the positions of the steering wheel, the seat, or the inside or

outside rear view mirrors while driving. Doing so may result in a loss of vehicle control.

●Always check that all passengers’ arms, heads or other parts of their body

are not outside the vehicle.

●Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires. Driving over 85 mph (140 km/h) may result in tire failure, loss of control and possible injury. Be sure to consult a tire dealer to determine whether the tires on your vehicle are high-speed capability tires or not before driving at such speeds.

4RUNNER (U)_(OM35B18U)

162

4-1. Before driving

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■When driving on slippery road surfaces

●Sudden braking, acceleration and steering may cause tire slippage and

reduce your ability to control the vehicle, resulting in an accident.

●Sudden acceleration, engine braking due to shifting, or changes in engine

speed could cause the vehicle to skid, resulting in an accident.

●After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.

■When shifting the shift lever

●Do not let the vehicle roll backward while the shift lever is in a driving posi-

tion, or roll forward while the shift lever is in R. Doing so may cause the engine to stall or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle.

●Do not shift the shift lever to P while the vehicle is moving.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Do not shift the shift lever to R while the vehicle is moving forward.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Do not shift the shift lever to D while the vehicle is moving backward.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Moving the shift lever to N while the vehicle is moving will disengage the engine from the transmission. Engine braking is not available when N is selected.

●Be careful not to shift the shift lever with the accelerator pedal depressed. Shifting the shift lever to a gear other than P or N may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

163

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■If you hear a squealing or scraping noise (brake pad wear limit indica-

tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage may result if the pads are not replaced when needed. It is dangerous to drive the vehicle when the wear limits of the brake pads and/or those of the brake discs are exceeded.

■When the vehicle is stopped

●Do not race the engine.

If the vehicle is in any gear other than P or N, the vehicle may accelerate suddenly and unexpectedly, causing an accident.

●In order to prevent accidents due to the vehicle rolling away, always keep depressing the brake pedal while the engine is running, and apply the parking brake as necessary.

●If the vehicle is stopped on an incline, in order to prevent accidents caused by the vehicle rolling forward or backward, always depress the brake pedal and securely apply the parking brake as needed.

●Avoid revving or racing the engine.

Running the engine at high speed while the vehicle is stopped may cause the exhaust system to overheat, which could result in a fire if combustible material is nearby.

4RUNNER (U)_(OM35B18U)

164

4-1. Before driving

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■When the vehicle is parked

fire.

●Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in

the vehicle when it is in the sun. Doing so may result in the following: • Gas may leak from a cigarette lighter or spray can, and may lead to a

• The temperature inside the vehicle may cause the plastic lenses and

plastic material of glasses to deform or crack.

• Soft drink cans may fracture, causing the contents to spray over the interior of the vehicle, and may also cause a short circuit in the vehicle’s electrical components.

●Do not leave cigarette lighters in the vehicle. If a cigarette lighter is in a place such as the glove box or on the floor, it may be lit accidentally when luggage is loaded or the seat is adjusted, causing a fire.

●Do not attach adhesive discs to the windshield or windows. Do not place containers such as air fresheners on the instrument panel or dashboard. Adhesive discs or containers may act as lenses, causing a fire in the vehi- cle.

●Do not leave a door or window open if the curved glass is coated with a metallized film such as a silver-colored one. Reflected sunlight may cause the glass to act as a lens, causing a fire.

●Always apply the parking brake, shift the shift lever to P, stop the engine

and lock the vehicle. Do not leave the vehicle unattended while the engine is running.

●Do not touch the exhaust pipes while the engine is running or immediately

after turning the engine off. Doing so may cause burns.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

165

CAUTION

Observe the following precautions. Failure to do so may result in death or serious injury. ■When taking a nap in the vehicle

Always turn the engine off. Otherwise, if you accidentally move the shift lever or depress the accelerator pedal, this could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.

■When braking

●When the brakes are wet, drive more cautiously.

Braking distance increases when the brakes are wet, and this may cause one side of the vehicle to brake differently than the other side. Also, the parking brake may not securely hold the vehicle.

●If the power brake assist function does not operate, do not follow other

vehicles closely and avoid hills or sharp turns that require braking. In this case, braking is still possible, but the brake pedal should be depressed more firmly than usual. Also, the braking distance will increase.

●Do not pump the brake pedal if the engine stalls.

Each push on the brake pedal uses up the reserve for the power-assisted brakes.

●The brake system consists of 2 individual hydraulic systems; if one of the systems fails, the other will still operate. In this case, the brake pedal should be depressed more firmly than usual and the braking distance will increase. If this happens, do not continue to drive the vehicle. Have your brakes fixed immediately.

4RUNNER (U)_(OM35B18U)

166

4-1. Before driving

NOTICE

■When driving the vehicle

●Do not depress the accelerator and brake pedals at the same time during

driving, as this may restrain driving torque.

●Do not use the accelerator pedal or depress the accelerator and brake

pedals at the same time to hold the vehicle on a hill.

■When parking the vehicle

Always shift the shift lever to P. Failure to do so may cause the vehicle to move or the vehicle may accelerate suddenly if the accelerator pedal is accidentally depressed.

■Avoiding damage to vehicle parts

●Do not turn the steering wheel fully in either direction and hold it there for

an extended period of time. Doing so may damage the power steering pump.

●When driving over bumps in the road, drive as slowly as possible to avoid

damaging the wheels, underside of the vehicle, etc.

■If you get a flat tire while driving

A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually depress the brake pedal to slow down the vehi- cle. ●It may be difficult to control your vehicle. ●The vehicle will make abnormal sounds or vibrations. ●The vehicle will behave abnormally. Information on what to do in case of a flat tire (P. 428)

4RUNNER (U)_(OM35B18U)

4-1. Before driving

167

NOTICE

■When encountering flooded roads

Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle: ●Engine stalling ●Short in electrical components ●Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following: ●Brake function ●Changes in quantity and quality of oil and fluid used for the engine, trans-

mission, transfer (4WD models), differentials, etc.

●Lubricant condition for the propeller shaft, bearings and suspension joints

(where possible), and the function of all joints, bearings, etc.

4RUNNER (U)_(OM35B18U)

168

4-1. Before driving

Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load: ● Stow cargo and luggage in the luggage compartment whenever

possible.

● Be sure all items are secured in place. ● To maintain vehicle balance while driving, position luggage evenly

within the luggage compartment.

● For better fuel economy, do not carry unnecessary weight.

4RUNNER (U)_(OM35B18U)

4

4-1. Before driving

169

Capacity and distribution Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) — (Total weight of occupants) Steps for Determining Correct Load Limit — (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard.

(2) Determine the combined weight of the driver and passengers that

will be riding in your vehicle.

(3) Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4) The resulting figure equals the available amount of cargo and lug-

gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400  750 (5150) = 650 lbs.)

(5) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

(6) If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (P. 456)

4RUNNER (U)_(OM35B18U)

170

4-1. Before driving

Calculation formula for your vehicle

Cargo capacity Total capacity weight) (P. 456)

load capacity

(vehicle

When 2 people with the combined weight of A lb. (kg) are riding in your vehicle, which has a total load capacity (vehicle capacity weight) of B lb. (kg), the available amount of cargo and luggage load capacity will be C lb. (kg) as follows: B*2 lb. (kg) - A*1 lb. (kg) = C*3 lb. (kg) *1: A =Weight of people *2: B =Total load capacity *3: C =Available cargo and luggage load

In this condition, if 3 more passengers with the combined weight of D lb. (kg) get on, the available cargo and luggage load will be reduced E lb. (kg) as follows:

C lb. (kg) - D*4 lb. (kg) = E*5 lb. (kg) *4: D =Additional weight of people *5: E =Available cargo and luggage load As shown in the example above, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

4RUNNER (U)_(OM35B18U)

4-1. Before driving

171

Roof rails

Cross rails

■When using the roof rails (if equipped) ●To use the roof rails as a roof luggage carrier, you must fit the roof rails with two or more genuine Toyota cross rails or their equivalent.

●When there is no luggage on the roof luggage carrier Toyota recommends that the front and rear cross rails be secured in the positions indicated in the illustration. This may reduce wind noise while driving.

CAUTION

■Things that must not be carried in the luggage compartment

The following things may cause a fire if loaded in the luggage compart- ment: ●Receptacles containing gasoline ●Aerosol cans

■Storage precautions

Observe the following precautions. Failure to do so may prevent the pedals from being depressed properly, may block the driver’s vision, or may result in items hitting the driver or passengers, possibly causing an accident. ●Stow cargo and luggage in the luggage compartment whenever possi-

ble.

●Do not stack cargo and luggage in the luggage compartment higher

than the seatbacks.

●Do not place cargo or luggage in or on the following locations.

• At the feet of the driver • On the front passenger or rear seats (when stacking items) • On the instrument panel • On the dashboard

●Secure all items in the occupant compartment. ●When you fold down the rear seats, long items should not be placed

directly behind the front seats.

●Never allow anyone to ride in the luggage compartment. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or serious bodily injury, in the event of sudden braking, sudden swerving or an accident.

4RUNNER (U)_(OM35B18U)

172

4-1. Before driving

CAUTION

■Capacity and distribution

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.

■When loading cargo on the roof luggage carrier

Observe the following precautions: ●Place the cargo so that its weight is distributed evenly between the

front and rear axles.

●If loading long or wide cargo, never exceed the vehicle overall length

or width. (P. 456)

●Before driving, make sure the cargo is securely fastened on the roof

luggage carrier.

●Loading cargo on the roof luggage carrier will make the center of grav- ity of the vehicle higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle correctly and result in death or serious injury.

●If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then during the trip to make sure the cross rails