2012 Toyota 4runner Owners Manual

To prevent the steering lock motor from overheating, the motor may be sus- pended if the engine is turned on and off repeatedly in a short period of time. In this case, refrain from operating the engine. After about 10 seconds, the steering lock motor will resume functioning.

■When the “ENGINE START STOP” switch indicator flashes in amber

The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately.

■If the electronic key battery is depleted

→P. 552

176

4RUNNER_U

2

2-1. Driving procedures

CAUTION

■When starting the engine

Always start the engine while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

■Caution while driving

If the vehicle begins to slide due to engine failure or other circumstances, do not lock or open the doors until the vehicle reaches a safe and complete stop. Activation of the steering lock in this circumstance may lead to an acci- dent, resulting in death or serious injury. ■Stopping the engine in an emergency

If you want to stop the engine in an emergency while driving the vehicle, press and hold the “ENGINE START STOP” switch for more than 3 seconds. However, do not touch the “ENGINE START STOP” switch while driving except in an emergency. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so.

177

4RUNNER_U

2-1. Driving procedures

NOTICE

■To prevent battery discharge

●Do not leave the “ENGINE START STOP” switch in ACCESSORY or IGNI-

TION ON mode for long periods of time without the engine running.

●If the indicator on the “ENGINE START STOP” switch is illuminated, the “ENGINE START STOP” switch is not off. When exiting the vehicle, always check that the “ENGINE START STOP” switch is off.

●Do not stop the engine when the shift lever is in a position other than P. If the engine is stopped in another shift lever position, the “ENGINE START STOP” switch will not be turned off but instead be turned to ACCESSORY mode. If the vehicle is left in ACCESSORY mode, battery discharge may occur.

■When starting the engine ●Do not race a cold engine. ●If the engine becomes difficult to start or stalls frequently, have the engine

checked immediately.

■Symptoms indicating a malfunction with the “ENGINE START STOP”

switch If the “ENGINE START STOP” seems to be operating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction. Contact your Toyota dealer immediately.

178

4RUNNER_U

2-1. Driving procedures Automatic transmission

Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever

CTH21AS014

Vehicles without a smart key system: While the engine switch is in the “ON” position, move the shift lever with the brake pedal depressed. Vehicles with a smart key system: While the “ENGINE START STOP” switch is in IGNITION ON mode, move the shift lever with the brake pedal depressed. When shifting the shift lever between P and D, make sure that the vehicle is completely stopped.

179

4RUNNER_U

2-1. Driving procedures

■ Shift position purpose

Shift position

Function

Parking the vehicle/starting the engine

Reversing Neutral

Normal driving*1

S mode driving*2 (→P. 181)

*1: To improve fuel efficiency and reduce noises, set the shift lever in the D

position for normal driving.

*2: Selecting shift ranges using S mode restricts the upper limit of the pos- sible gear ranges, controls engine braking forces, and prevents unnec- essary upshifting.

180

4RUNNER_U

2-1. Driving procedures

Changing shift ranges in S mode

When the shift lever is in the S position, the shift lever can be oper- ated as follows: Non-Optitron type meter

For upshifting For downshifting

Optitron type meter

CTH21AS025

For upshifting For downshifting

CTH21AS015

The initial shift range in S mode is set automatically to “4” according to vehicle speed. However, the initial shift range may be set to “3” if AI-SHIFT has operated while the shift lever was in the D position. (→P. 182) ■ Shift ranges and their functions

● You can choose from 5 levels of engine braking force. ● A lower shift range will provide greater engine braking force than

a higher shift range, and the engine speed will also increase.

181

4RUNNER_U

2-1. Driving procedures

■S mode

When the shift range is “3” or lower, holding the shift lever toward “+” sets the shift range to “5”.

■AI-SHIFT

AI-SHIFT automatically selects the optimal gear according to driver perfor- mance and driving conditions. AI-SHIFT automatically operates when the shift lever is in the D position. (Shifting the shift lever to the S position cancels the function.) The engine speed may remain high after releasing the accelerator pedal. This does not indicate a malfunction.

■When driving with the cruise control system

Engine braking will not occur in S mode, even when downshifting to “4”. (→P. 217)

■If the shift lever cannot be shifted from P

→P. 618

■If the “S” indicator does not come on even after shifting the shift lever

to S This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the transmission will operate in the same manner as when the shift lever is in D.)

■Downshift restriction warning buzzer (S mode)

To help ensure safety and driving performance, downshifting operation may sometimes be restricted. In some circumstances, downshifting may not be possible even when the shift lever is operated. (A buzzer will sound twice.)

CAUTION

■When driving on slippery road surfaces Do not accelerate or shift gears suddenly. Sudden changes in engine braking may cause the vehicle to spin or skid, resulting in an accident.

182

4RUNNER_U

2

2-1. Driving procedures Turn signal lever

The turn signal lever can be used to show the following intentions of the driver:

Right turn Left turn Lane change to the right (push and hold the lever partway) The right hand signals will flash until you release the lever. Lane change left (push and hold the lever partway) The left hand signals will flash until you release the lever.

the

to

CTH21AS028

■Turn signals can be operated when

Vehicles without a smart key system: The engine switch is in the “ON” posi- tion. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode.

■If the indicator flashes faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

183

4RUNNER_U

2-1. Driving procedures Parking brake

U.S.A. Canada

To set the parking brake, fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot. (Depressing the pedal again releases the parking brake.)

CTH21AS031

■Usage in winter time

See “Winter driving tips” for parking brake usage in winter time. (→P. 288)

NOTICE

■Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

184

4RUNNER_U

2-1. Driving procedures Horn

To sound the horn, press on or close to the

mark.

CTH21AS022

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P. 93)

185

4RUNNER_U

2-2. Instrument cluster Gauges and meters

Non-Optitron type meters

Optitron type meters

186

4RUNNER_U

2

2-2. Instrument cluster

Tachometer Displays the engine speed in revolutions per minute Speedometer Displays the vehicle speed Display change button →P. 188
Engine coolant temperature gauge Displays the engine coolant temperature Fuel gauge Displays the quantity of fuel remaining in the tank Eco Driving Indicator Zone Display →P. 189
Odometer, trip meter and average fuel consumption display →P. 188
Shift position and shift range indicators →P. 179
Voltmeter Displays the charge state

187

4RUNNER_U

2-2. Instrument cluster

Switching the display

Items displayed can be switched by pressing the display change button.

■ Odometer

Displays the total distance the vehicle has been driven.

■ Trip meter

Displays the distance the vehicle has been driven since the meter was last reset. Trip meters “A” and “B” can be used to record and display different distances independently. Pressing and holding the display change button will reset the trip meter that is currently displayed.

188

4RUNNER_U

2

2-2. Instrument cluster

■ Eco Driving Indicator and average fuel consumption Non-Optitron type meter

CTH22AS054

Indicator Zone

Eco Driving Indicator Light During Eco-friendly acceleration (Eco driving), Eco Driving Indica- tor Light will turn on. Eco Driving Display Suggests Zone of Eco driving with current Eco driving ratio based on acceleration. Zone of Eco driving Eco driving ratio based on acceleration In case over-use of the accelera- tor causes the vehicle to exceed Zone of Eco driving, the right of Eco Driving Indicator Zone Dis- play will blink and Eco Driving Indicator Light will turn off. Average fuel consumption Displays the average fuel con- sumption since the function was reset. Pressing and holding the display change button will reset the aver- age fuel consumption. Use the displayed average fuel consumption as a reference.

189

4RUNNER_U

2-2. Instrument cluster

Optitron type meter

Indicator Zone

Eco Driving Indicator Light During Eco-friendly acceleration (Eco driving), Eco Driving Indica- tor Light will turn on. Eco Driving Display Suggests Zone of Eco driving with current Eco driving ratio based on acceleration. Zone of Eco driving Eco driving ratio based on acceleration In case over-use of the accelera- tor causes the vehicle to exceed Zone of Eco driving, the right of Eco Driving Indicator Zone Dis- play will blink and Eco Driving Indicator Light will turn off. Average fuel consumption Displays the average fuel con- sumption since the function was reset. Pressing and holding the display change button will reset the aver- age fuel consumption. Use the displayed average fuel consumption as a reference.

CTH22AS055

190

4RUNNER_U

2-2. Instrument cluster

■ Eco Driving Indicator Light customization Non-Optitron type meter

Eco Driving Indicator Light can be activated or deactivated by pressing and holding the display change button.

Optitron type meter

Eco Driving Indicator Light can be activated or deactivated by pressing and holding the display change button.

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Brighter Darker

CTH22AS010

191

4RUNNER_U

2-2. Instrument cluster

■The meters and display illuminate when (Optitron type meter)

Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode.

■Eco Driving Indicator Light will not operate in the following conditions

●The shift lever is anything other than D. ●The vehicle speed is approximately 80 mph (130 km/h) or higher.

■When the average fuel consumption is reset

The average fuel consumption displayed on the accessory meter and “Past Record” screen of the Display Audio system (if equipped) or the navigation system (if equipped) will be reset at the same time.

■The brightness of the instrument panel lights (Optitron type meter)

When the headlight switch is turned to on, the brightness will be reduced slightly unless the control dial is turned fully upward.

NOTICE

■To prevent damage to the engine and its components

●Do not let the indicator needle of the tachometer enter the red zone, which

indicates the maximum engine speed.

●The engine may be overheating if the engine coolant temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 627)

■While driving (Optitron type meter)

When the voltmeter indicates more than 19 V or less than 9 V, the battery may be malfunctioning. Have your vehicle checked at your Toyota dealer.

192

4RUNNER_U

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster (non-Optitron type meters)

Instrument cluster (Optitron type meters)

CTH22AS068

CTH22AS069

193

4RUNNER_U

2-2. Instrument cluster

Center panel

CTH22AS015

194

4RUNNER_U

2-2. Instrument cluster

■ Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

*1

Roll sensing of curtain shield airbags off indica- tor (→P. 134)

(if equipped) *1

(if equipped)

(if equipped)

(if equipped)

(if equipped)

(if equipped) *1

(if equipped)

(if equipped)

Four-wheel drive indica- tor (→P. 236)

Downhill assist control system indicator (→P. 251)

Low speed four-wheel drive indicator (→P. 236, 239)

Rear differential lock indicator (→P. 248)

Center differential lock indicator (→P. 239)

“A-TRAC” indicator (→P. 243)

“AUTO LSD” indicator (→P. 245)

Multi-terrain Select indi- cator (→P. 258)

195

Turn signal indicator (→P. 183)

Headlight high beam indicator (→P. 207)

Headlight indicator (→P. 203)

Tail light indicator (→P. 203)

(U.S.A.)

(Canada)

Front fog light indicator (→P. 209)

Cruise control indicator (→P. 217)

Cruise control set indi- cator (→P. 217)

*1, 2

*1

*1

Slip indicator (→P. 267)

VSC off indicator (→P. 268)

“TRAC OFF” indicator (→P. 268)

4RUNNER_U

2-2. Instrument cluster

*1

(if equipped) *1

Crawl Control indicator (→P. 254)

Security indicator (→P. 113, 116)

Eco Driving Indicator Light (→P. 189)

*1

SRS airbag on-off indi- cator (→P. 136)

Intuitive parking assist indicator (→P. 221)

Automatic running boards indicator (→P. 59)

(if equipped) *1, 2

(if equipped)

*1: These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key system) or the engine switch is turned to the “ON” position (vehicles without a smart key system) to indicate that a system check is being per- formed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.

*2: The light flashes to indicate that the system is operating.

196

4RUNNER_U

2-2. Instrument cluster

■ Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 587)

*1

*3

*1

*1

(U.S.A.) *3

(Canada) *3

*1

*3

*1

(U.S.A.) *4

(if equipped) (if equipped) (if equipped) (if equipped) (if equipped)

*1

*1

*1

*1

*1

(U.S.A.) *1

(Canada) *2

(Canada) *1

(U.S.A.)

*1

*1

(Canada) *1

(if equipped) *1

*1, 2

(if equipped) (if equipped)

(if equipped) *1: These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key system) or the engine switch is turned to the “ON” position (vehicles without a smart key system) to indicate that a system check is being per- formed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.

*2: The light flashes to indicate a malfunction. *3: The light flashes rapidly to indicate a malfunction. *4: The light flashes continuously to indicate a malfunction.

197

4RUNNER_U

2-2. Instrument cluster

CAUTION

■If a safety system warning light does not come on

Should a safety system light such as the ABS or SRS warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

198

4RUNNER_U

2-2. Instrument cluster Accessory meter

The accessory meter presents the driver with a variety of driving- related data including the current outside air temperature.

” button

” button

“MODE/ “SET/ Trip information (→P. 200) Displays driving range and average fuel consumption Outside temperature display (→P. 457) Compass (→P. 474) Clock (→P. 455) H (Hour) button (→P. 455) M (Minute) button (→P. 455) Multi-terrain Select display (→P. 258) Automatically displayed when using Multi-terrain Select

199

4RUNNER_U

2-2. Instrument cluster

Trip information

Items displayed can be switched by pressing the “MODE/ ■ Driving range

” button.

(vehicles without Multi-terrain Select)

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining

• This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed. • When only a small amount of fuel is added to the

tank, the display may not be updated.

(vehicles with Multi-terrain Select)

■ Average fuel consumption

Displays the average fuel consumption since the function was reset

• Pressing and holding the “SET/

reset the average fuel consumption.

” button will

• Use the displayed average fuel consumption as a

reference.

(vehicles without Multi-terrain Select)

(vehicles with Multi-terrain Select)

200

4RUNNER_U

2-2. Instrument cluster

Accessory meter light control

The daytime brightness of the accessory meter can be adjusted.

STEP 1

STEP 2

Turn the headlight switch off. Press and hold the “MODE/ Press the “MODE/

” or “SET/ Vehicles without Multi-terrain Select

STEP 3

” button.

” button.

Vehicles with Multi-terrain Select

STEP 4

Press and hold the “SET/

” button.

201

4RUNNER_U

2-2. Instrument cluster

■When the average fuel consumption is reset

The average fuel consumption displayed on the instrument cluster and “Past Record” screen of the Display Audio system (if equipped) or the navigation system (if equipped) will be reset at the same time. ■Adjusting the brightness of the accessory meter

●If left idle for approximately 6 seconds or more while adjusting, the dis-

play will revert to the trip information display.

●When the parking lights are on, the brightness of the accessory meter

can be adjusted only with the instrument panel light control.

●If the “MODE/

” button is pressed and held when the accessory meter light control is displayed, the display will switch to compass calibration. (→P. 474)

■Liquid crystal display

Small spots or light spots may appear on the display. This phenomenon is characteristic of liquid crystal displays, and there is no problem with continu- ing to use the display.

NOTICE

■The accessory meter at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal dis- play. At extremely low temperatures, the display monitor may respond slowly, and display changes may be delayed.

202

4RUNNER_U

2

2-3. Operating the lights and wipers Headlight switch

The headlights can be operated manually or automatically. Turning the end of the lever turns on the lights as follows: Type A

run-

lights

The daytime ning lights turn on. The side marker, parking, tail, license plate, daytime run- ning and instrument panel lights turn on. The headlights and all the lights listed above turn on. The daytime ning lights turn off.

run-

CTH23AS046

203

4RUNNER_U

is

in

headlights, The parking lights, day- time running lights and so on turn on and off automatically (when the “ENGINE STOP” START switch IGNI- TION ON mode). The side marker, parking, tail, license plate, daytime run- and ning instrument panel lights turn on. The headlights and all the lights listed above turn on. The daytime ning lights turn off.

lights

run-

2-3. Operating the lights and wipers

Type B

CTH23AS047

204

4RUNNER_U

2

Type C

2-3. Operating the lights and wipers

run-

The daytime ning lights turn on. The side marker, parking, tail, license plate and instru- ment panel lights turn on. The headlights and all the lights listed above turn on.

CTH23AS048

205

4RUNNER_U

is

The daytime running lights turn on. The headlights, park- ing lights, daytime running lights and so on turn on and off automatically (when the “ENGINE STOP” START switch IGNI- TION ON mode). The side marker, parking, tail, license plate, daytime run- ning and instrument panel lights turn on. The headlights and all the lights listed above turn on.

lights

in

2-3. Operating the lights and wipers

Type D

CTH23AS049

206

4RUNNER_U

2

2-3. Operating the lights and wipers

Turning on the high beam headlights

With the headlights on, push the lever away from you to turn on the high beams. Pull the lever toward you to the center position to turn the high beams off. Pull the lever toward you and release it to flash the high beams once. You can flash the high beams with the headlights on or off.

CTH23AS040

■Daytime running light system

●To make your vehicle more visible to other drivers, the daytime running lights turn on automatically whenever the engine is started and the park- ing brake is released. Daytime running lights are not designed for use at night. Type A and B: Daytime running lights can be turned off by operating the switch.

●Compared to turning on the headlights, the daytime running light system offers greater durability and consumes less electricity, so it can help improve fuel economy.

■Headlight control sensor (if equipped)

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the automatic headlight sys- tem to malfunction.

interferes with

CTH23AS012

207

4RUNNER_U

2-3. Operating the lights and wipers

■Automatic light off system

Vehicles without a smart key system ●When the headlights come on: The headlights and tail lights turn off 30
seconds after a door is opened and closed if the engine switch is turned to the “ACC” or “LOCK” position. (The lights turn off immediately if

on the key is pressed after all the doors are locked.)

●When only the tail lights come on: The tail lights turn off automatically if the engine switch is turned to the “ACC” or “LOCK” position and the driver’s door is opened.

or

To turn the lights on again, turn the engine switch to the “ON” position, or turn the lights off and then back to Vehicles with a smart key system ●When the headlights come on: The headlights and tail lights turn off 30
seconds after a door is opened and closed if the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. (The lights turn off immediately if on the key is pressed after all the doors are locked.)

●When only the tail lights come on: The tail lights turn off automatically if the “ENGINE START STOP” switch is turned off and the driver’s door is opened.

To turn the lights on again, turn the “ENGINE START STOP” switch to IGNI- or TION ON mode, or turn the light switch off and then back to

■Customization that can be configured at Toyota dealer

Settings (e.g. light sensor sensitivity) can be changed. (Customizable features →P. 660)

NOTICE

■To prevent battery discharge

Do not leave the lights on longer than necessary when the engine is not run- ning.

208

4RUNNER_U

2-3. Operating the lights and wipers Fog light switch

The fog lights secure excellent visibility in difficult driving condi- tions, such as in rain and fog. Type A

Turns the front fog lights off Turns the front fog lights on

CTH23AS041

209

4RUNNER_U

2-3. Operating the lights and wipers

Type B

Turns the front fog lights off Turns the front fog lights on

CTH23AS010

■Fog lights can be used when

The headlights are on in low beam.

210

4RUNNER_U

2

2-3. Operating the lights and wipers Windshield wipers and washer

When intermittent windshield wiper operation is selected, the wiper interval can be adjusted. The wiper operation is selected by moving the lever as follows. Type A

wind- Intermittent shield wiper opera- tion Low speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation

the

Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency

CTH23AS042

CTH23AS043

211

4RUNNER_U

2-3. Operating the lights and wipers

Type B

CTH23AS044

Washer/wiper dual opera- tion The wipers will automatically operate a couple of times after the washer squirts.

Intermittent wind- shield wiper opera- tion Low speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation

the

Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency

CTH23AS027

CTH23AS028

212

4RUNNER_U

2-3. Operating the lights and wipers

Washer/wiper dual opera- tion The wipers will automatically operate a couple of times after the washer squirts.

CTH23AS029

■The windshield wipers and washer can be operated when

Vehicles without a smart key system: The engine switch is in the “ON” posi- tion. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode.

■If no windshield washer fluid sprays

Check that the washer nozzles are not blocked if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

■When the windshield is dry

Do not use the wipers, as they may damage the windshield.

■When the washer fluid tank is empty

Do not operate the switch continually as the washer fluid pump may over- heat.

■When a nozzle becomes blocked

Do not try to clear it with a pin or other object. The nozzle will be damaged.

213

4RUNNER_U

2-3. Operating the lights and wipers Rear window wiper and washer

Before operating the rear window wiper and washer switch, make sure the back window is completely closed. (→P. 101) The wiper operation is selected by moving the lever as follows: Type A

Intermittent window wiper operation Normal window wiper oper- ation Washer/wiper dual opera- tion Washer/wiper dual opera- tion The wiper will automatically operate a couple of times after the washer squirts. (After operating several times, the wiper operates one more time after a short delay to pre- vent dripping.)

CTH23AS045

214

4RUNNER_U

2

Type B

2-3. Operating the lights and wipers

Intermittent window wiper operation Normal window wiper oper- ation Washer/wiper dual opera- tion Washer/wiper dual opera- tion The wiper will automatically operate a couple of times after the washer squirts. (After operating several times, the wiper operates one more time after a short delay to pre- vent dripping.)

CTH23AS035

■The rear window wiper and washer can be operated when

●Vehicles without a smart key system: The engine switch is in the “ON”

position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode.

●The back window is completely closed.

■Intermittent window wiper operation

●When intermittent window wiper operation mode is selected, the wiper

will operate a couple of times and then switch to intermittent operation.

●During intermittent operation, the wiper stops temporarily at the reversing

position.

215

4RUNNER_U

2-3. Operating the lights and wipers

■When the rear window wiper and washer switch is turned off

The rear wiper will stop operation, and return to the retracted position after approximately 3 seconds. However, if the engine switch is turned to the “ACC” or “LOCK” position (vehicles without a smart key system) or the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off (vehicles with a smart key sys- tem) while the rear wiper is operating, the rear wiper will stop at that position and will not return to the retracted position.

■If no washer fluid sprays

Check that the washer nozzle is not blocked if there is washer fluid in the washer fluid reservoir.

■Customization that can be configured at Toyota dealer

Settings (e.g. drip prevention function) can be changed. (Customizable features →P. 660)

NOTICE

■When the rear window is dry

Do not use the wiper, as it may damage the rear window.

■When the washer fluid tank is empty

Do not operate the switch continually as the washer fluid pump may over- heat.

■When a nozzle becomes blocked

Do not try to clear it with a pin or other object. The nozzle will be damaged.

216

4RUNNER_U

2-4. Using other driving systems Cruise control

Use the cruise control to maintain a set speed without depressing the accelerator pedal.

Indicators Cruise control switch

■ Setting the vehicle speed

CTH24AS001

STEP 1

Press the “ON-OFF” button to activate the cruise control.

indicator will

Cruise control come on. Press deactivate the cruise control.

the button again

to

STEP 2

CTH24AS002

CTH24AS057

Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set the speed.

“SET” indicator will come on. The vehicle speed at the moment the lever is released becomes the set speed.

217

4RUNNER_U

2-4. Using other driving systems

■ Adjusting the set speed

To change the set speed, operate the lever until the desired set speed is obtained.

Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold lever in the desired direction.

the

CTH24AS004

The set speed will be increased or decreased as follows: Fine adjustment: By approximately 1 mph (1.6 km/h) each time the lever is operated. Large adjustment: The set speed can be increased or decreased con- tinually until the lever is released.

■ Canceling and resuming the constant speed control

Pulling the lever toward you cancels the constant speed control. The speed setting is also can- celed when the brakes are applied. Pushing resumes speed control. Resuming is available when the vehicle speed is more than approximately 25 mph (40 km/h).

lever up constant

the the

CTH24AS005

218

4RUNNER_U

2-4. Using other driving systems

■Cruise control can be set when

●The shift lever is in the D or range 4 or higher of S has been selected. ●Vehicle speed is above approximately 25 mph (40 km/h).

■Accelerating after setting the vehicle speed

●The vehicle can be accelerated normally. After acceleration, the set

speed resumes.

●Even without cancelling the cruise control, the set speed can be increased by first accelerating the vehicle to the desired speed and then pushing the lever down to set the new speed.

■Automatic cruise control cancelation

Cruise control will stop maintaining the vehicle speed in any of the following situations. ●Actual vehicle speed falls more than approximately 10 mph (16 km/h)

below the preset vehicle speed. At this time, the memorized set speed is not retained.

●Actual vehicle speed is below approximately 25 mph (40 km/h). ●VSC is activated.

■If the cruise control indicator light flashes

Press the “ON-OFF” button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.

219

4RUNNER_U

2-4. Using other driving systems

CAUTION

■To avoid operating the cruise control by mistake

Switch the cruise control off using the “ON-OFF” button when not in use.

■Situations unsuitable for cruise control

Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills

Vehicle speed may exceed the set speed when driving down a steep hill.

●When your vehicle is towing a trailer

220

4RUNNER_U

2-4. Using other driving systems Intuitive parking assist∗

The distance from your vehicle to nearby obstacles when parallel parking or maneuvering into a garage is measured by the sensors and communicated via an indicator and a buzzer. Always check the surrounding area when using this system. ■ Types of sensors

Rear corner sensors Rear center sensors

■ Intuitive parking assist switch

intuitive parking

Turns the assist on/off When on, the indicator light comes on and the buzzer sounds to inform the driver that the system is operational.

CTH24AS008

∗: If equipped 221

4RUNNER_U

2-4. Using other driving systems

The indicator and buzzer

When a sensor detects an obstacle, the direction of the obstacle is indicated and the buzzer sounds. ■ Sensor operation and distance to an obstacle

The system operates when the vehicle approaches an obstacle, as shown by the following table.

Rear corner sensors

Distance to an obstacle ft. (cm) Approximately 1.6 - 1.2 (50 - 37.5) Approximately 1.2 - 0.8 (37.5 - 25) Approximately 0.8 or less (25 or less)

Rear center sensors

Indicator and buzzer

Intermittent

Fast intermittent

Continuously

Distance to an obstacle ft. (cm)

Indicator and buzzer

Approximately 4.9 - 2.0 (150 - 60) Approximately 2.0 - 1.5 (60 - 45) Approximately 1.5 - 1.2 (45 - 35) Approximately 1.2 or less (35 or less)

Intermittent

Fast intermittent

Very fast intermittent

Continuously

222

4RUNNER_U

2

Detection range of the sensors

2-4. Using other driving systems

Approximately 1.6 ft. (50 cm) Approximately 4.9 ft. (150 cm) The diagram shows the detection range of the sensors. Note that the sensors cannot detect obsta- cles that are extremely close to the vehicle. The range of the sensors may change depending on the shape of the object etc.

CTH24AS081

■Intuitive parking assist can be operated when

Vehicles without a smart key system: The engine switch is in the “ON” posi- tion and the shift lever is in R. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode and the shift lever is in R.

223

4RUNNER_U

2-4. Using other driving systems

■Sensor detection information

●Certain vehicle conditions and the surrounding environment may affect the ability of a sensor to correctly detect an obstacle. Particular instances where this may occur are listed below. • There is dirt, snow or ice on a sensor. • A sensor is frozen. • A sensor is covered in any way. • The vehicle is leaning considerably to one side. • On an extremely bumpy road, on an incline, on gravel, or on grass • The vicinity of the vehicle is noisy due to vehicle horns, motorcycle engines, air brakes of large vehicles, or other loud noises producing ultrasonic waves.

• There is another vehicle equipped with parking assist sensors in the

• A sensor is coated with a sheet of spray or heavy rain. • A bumper or sensor receives a strong impact. • The vehicle is approaching a tall or right-angled curb. • In harsh sunlight or intense cold weather • A non-genuine Toyota suspension (lowered suspension etc.) is

vicinity.

installed.

In addition to the examples above, there are instances in which, because of their shape, signs and other objects may be judged by a sensor to be closer than they are. ●The shape of the obstacle may prevent a sensor from detecting it. Pay

particular attention to the following obstacles: • Wires, fences, ropes, etc. • Cotton, snow and other materials that absorb sound waves • Sharply-angled objects • Low obstacles • Tall obstacles with upper sections projecting outwards in the direction

of your vehicle

224

4RUNNER_U

2

2-4. Using other driving systems

■When the system malfunctions

If a malfunction occurs and no obstacles have been detected, the indicator flashes and the buzzer sounds for approximately 7 seconds. If the indicator comes on and stays on after that, have the vehicle inspected by your Toyota dealer.

■Customization that can be configured at Toyota dealer

Settings (e.g. buzzer volume) can be changed. (Customizable features →P. 660)

■Certification

For vehicles sold in the U.S.A. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) This device may not cause harmful interfer- ence, and (2) This device must accept any interference received, including interference that may cause undesired operation. For vehicles sold in Canada This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme a la norme NMB-001 du Canada.

CAUTION

■Caution when using the intuitive parking assist-sensor

Do not attach any accessories within the sensor range. Doing so may result in the vehicle being unable to be driven safely and pos- sibly cause an accident.

NOTICE

■Notes when washing the vehicle

Do not apply intensive bursts of water or steam to the sensor area. Doing so may result in the sensor malfunctioning.

225

4RUNNER_U

2-4. Using other driving systems Rear view monitor system (rear view mirror-attached type)∗

The rear view monitor assists the driver by displaying an image of the area behind the vehicle while reversing. The image is displayed in reverse on the screen. This reversed image is a similar image to the one on the inside rear view mirror.

The rear view image is dis- played when the shift lever is in R. •

If the shift lever is shifted out of R, the screen is turned off.

• The screen remains on for

approximately 5 minutes.

CTH24AS076

∗: If equipped

226

4RUNNER_U

2

2-4. Using other driving systems

■ Rear view monitor guide lines

Guide lines are displayed on the screen.

CTH24AS077

The guide lines may look different depending on vehicle orientation or road conditions. Vehicle width extension guide lines (blue) These lines indicate the estimated vehicle width extension. Distance guide line (blue) This line indicates a position on the ground about 3 ft. (1 m) behind on the ground of the rear bumper of your vehicle. Distance guide line (red) This line indicates a position on the ground about 1.5 ft. (0.5 m) behind on the ground of the rear bumper of your vehicle. Vehicle center guide lines (blue) These lines indicate the estimated vehicle center on the ground.

227

4RUNNER_U

2-4. Using other driving systems

■The rear view monitor system can be operated when

Vehicles without a smart key system The shift lever is in R, the engine switch is in the “ON” position. Vehicles with a smart key system The shift lever is in R, the “ENGINE START STOP” switch is in IGNITION ON mode.

■Changing display modes

The rear view monitor display mode can be changed while the screen is on. ●To temporarily disable the rear view monitor system

Push the “AUTO” button. The indicator will turn amber. Vehicles without a smart key system The system will be re-enabled once the engine switch is turned OFF and then turned to the “ON” position. Vehicles with a smart key system The system will be re-enabled once the “ENGINE START STOP” switch is turned OFF and then turned to IGNI- TION ON mode.

CTH24AS080

●To constantly disable the rear view monitor system

Push and hold the “AUTO” button for 12 to 15 seconds. The screen will turn off and on after 6 seconds. Continue to push and hold the button until the screen turns back off. The indicator will flash amber. Vehicles without a smart key system The system will not automatically turn on again after the engine switch is turned OFF and then turned to the “ON” position. Vehicles with a smart key system The system will not automatically turn on again after the “ENGINE START STOP” switch is turned OFF and then turned to IGNITION ON mode.

●To re-enable the rear view monitor system

Push the “AUTO” button. The indicator will turn green.

228

4RUNNER_U

2

2-4. Using other driving systems

■Selecting a language (English, French or Spanish)

CTH24AS080

STEP 1

STEP 2

Push and hold the “AUTO” button for 6 to 12 seconds. The screen will turn on and the indicator will turn green. Push the “AUTO” button. Each time the “AUTO” switch is pushed, language changes. Stop pushing the button when the message is displayed in the desired lan- guage. After approximately 5
seconds, the warning mes- sage will flash once and the language will be set.

the

229

4RUNNER_U

2-4. Using other driving systems

■Displayed area

The area covered by the camera is lim- ited. Objects that are close to either cor- ner of the bumper or under the bumper cannot be seen on the screen. The area displayed on the screen may vary depending on vehicle orientation or road conditions.

CTH24AS082

Corners of bumper

CTH24AS078

CTH24AS083

230

4RUNNER_U

2-4. Using other driving systems

■Driving precautions

the grade behind

When the vehicle slopes up sharply, objects appear to be farther away than they actually are.