2012 Toyota 4runner Owners Manual

2-5. Driving information

CAUTION

■Roof luggage carrier precautions

When you load cargo on the roof luggage carrier, observe the following: ●Place the cargo so that its weight is distributed evenly between the

front and rear axles.

●If loading long or wide cargo, never exceed the vehicle overall length

or width. (→P. 634)

●Before driving, make sure the cargo is securely fastened on the roof

luggage carrier.

●Loading cargo on the roof luggage carrier will make the center of grav- ity of the vehicle higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle correctly and result in death or serious injury.

●If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then during the trip to make sure the cross rails are fixed securely and that the cargo remains in its place.

●Do not exceed 120 lb. (54 kg) cargo weight on the roof luggage carrier.

NOTICE

■When loading cargo

Be careful not to scratch the surface of the moon roof.

285

4RUNNER_U

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, trailer weight rating and cargo capacity. ■ Total load capacity

Without rear differential lock system: 1165 lb. (525 kg) With rear differential lock system (TRAIL): 835 lb. (375 kg) Total load capacity means the combined weight of occupants, cargo and luggage. ■ Seating capacity

Vehicle without third seats: 5 occupants (Front 2, Rear 3) Vehicle with third seats: 7 occupants (Front 2, Rear 5) Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. Even if the number of occupants are within the seating capacity, do not exceed the total load capacity.

■ Trailer weight rating: 5000 lb. (2270 kg)

Trailer weight rating means the maximum gross trailer weight (trailer weight plus its cargo weight) that you vehicle is able to tow.

■ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 543)

286

4RUNNER_U

2-5. Driving information

CAUTION

■Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

287

4RUNNER_U

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations

● Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

● Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

● Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the rear tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires.

288

4RUNNER_U

2

2-5. Driving information

■ Before driving the vehicle

Perform the following according to the driving conditions. ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. ● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

● Remove any ice that has accumulated on the vehicle chassis. ● Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

■ When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to the road conditions. ■ When parking the vehicle

Park the vehicle and move the shift lever to P without setting the parking brake. The parking brake may freeze up, preventing it from being released. If necessary, block the wheels to prevent inadvertent sliding or creeping.

289

4RUNNER_U

2-5. Driving information

Selection tire chains

Use the correct tire chain size when mounting the tire chains. Chain size is regulated for each tire size.

Side chain (0.20 in. [5 mm] in diameter) Cross chain (0.20 in. [5 mm] in diameter)

CTH25AS009

Regulations on the use of tire chains

Regulations regarding the use of tire chains vary depending on loca- tion and type of road. Always check local regulations before installing chains.

■Tire chain installation

Observe the following precautions when installing and removing chains: ●Install and remove tire chains in a safe location. ●Install tire chains on the rear tires only. Do not install tire chains on the

front tires.

●Install tire chains on rear tires as tightly as possible. Retighten chains

after driving 1/4 ⎯ 1/2 mile (0.5 ⎯ 1.0 km).

●Install tire chains following the instructions provided with the tire chains.

290

4RUNNER_U

2-5. Driving information

CAUTION

■Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failure to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the size specified. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

●Use snow tires on all, not just some wheels.

■Driving with tire chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being

used, or 30 mph (50 km/h), whichever is lower.

●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden turns and braking, as use of chains may adversely affect

vehicle handling.

●Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

291

4RUNNER_U

2-5. Driving information

NOTICE

■Repairing or replacing snow tires

Request repairs or replacement of snow tires from Toyota dealers or legiti- mate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

■Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

292

4RUNNER_U

2

2-5. Driving information Trailer towing

Your vehicle is designed primarily as a passenger-and-load-carrying vehicle. Towing a trailer can have an adverse impact on handling, performance, braking, durability, and fuel consumption. For your safety and the safety of others, you must not overload your vehicle or trailer. You must also ensure that you are using appropriate tow- ing equipment, that the towing equipment has been installed cor- rectly and used properly, and that you employ the requisite driving habits. Vehicle-trailer stability and braking performance are affected by trailer stability, brake performance and setting, trailer brakes, the hitch and hitch systems (if equipped). To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating condi- tions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional requirements such as a towing kit, etc.

293

4RUNNER_U

2-5. Driving information

Towing related terms

■ GCWR (Gross Combination Weight Rating)

The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the cargo in the trailer).

CTH25AS029

■ GVWR (Gross Vehicle Weight Rating)

The maximum allowable gross vehicle weight. The gross vehicle weight is the total weight of the vehicle. When towing a trailer, it is the sum of the vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the tongue weight.

CTH25AS030

294

4RUNNER_U

2-5. Driving information

■ GAWR (Gross Axle Weight Rating)

Front GAWR

Rear GAWR

The maximum allowable gross axle weight. The gross axle weight is the load placed on each axle (front and rear).

■ TWR (Trailer Weight Rating)

CTH25AS031

(With brakes)

CTH25AS019

The maximum allowable gross trailer weight. The gross trailer weight is the sum of the trailer weight and the weight of the cargo in the trailer. is calculated assuming TWR base vehicle with one driver, one front passenger, towing package (if available), hitch and hitch sys- tems (if required).

Additional optional equipment, passengers and cargo in the vehi- cle will reduce the trailer weight rating so as not to exceed GCWR, GVWR and GAWR. If the gross trailer weight exceeds 3000 lb. (1360 kg), it is recom- mended to use a trailer with 2 or more axles.

295

4RUNNER_U

2-5. Driving information

■ Unbraked TWR (Unbraked Trailer Weight Rating) (Without brakes)

The trailer weight rating for tow- ing a trailer without a trailer ser- vice brake system.

■ Tongue Weight

CTH25AS020

The load placed on the trailer hitch ball. (→P. 299)

CTH25AS021

296

4RUNNER_U

2

2-5. Driving information

Weight limits

● The gross trailer weight must never exceed the TWR described in

the table. (→P. 298)

● The gross combination weight must never exceed the GCWR

described in the table. (→P. 298)

● The gross vehicle weight must never exceed the GVWR indi- cated on the Certification Label.

● The gross axle weight on each axle must never exceed the GAWR indicated on the Certi- fication Label.

CTH61AS002

● If the gross trailer weight is over the unbraked TWR, trailer service

brakes are required.

● If the gross trailer weight is over 2000 lb. (907 kg), a sway control

device with sufficient capacity is required.

297

4RUNNER_U

2-5. Driving information

GCWR, TWR and Unbraked TWR

Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. ■ GCWR* and TWR*

Driving system

2WD 4WD

Trailer Weight

Rating

5000 lb. (2270 kg)

GCWR

11100 lb. (5035 kg) 11300 lb. (5125 kg)

■ Unbraked TWR* 1655 lb. (750 kg)

*: These models meet the tow-vehicle trailering requirement of SAE Interna-

tional per SAE J2807.

298

4RUNNER_U

2

2-5. Driving information

Trailer Tongue Weight

● A recommended tongue weight varies in accordance with the types

of trailers or towing as described below.

● To ensure the recommended values shown below, the trailer must

be loaded by referring to the following instructions. • Tongue Weight

The gross trailer weight should be distributed so that the tongue weight is 9% to 11%. (Tongue weight /Gross trailer weight x 100
= 9% to 11%)

Gross trailer weight Tongue weight

CTH25AS022

If using a weight distributing hitch when towing, return the front axle to the same weight as before the trailer connection. If front axle weight cannot be measured directly, measure the front fender height above the front axle before connection. Adjust weight distributing hitch torque until front fender is returned to the same height as before connection. The gross trailer weight, gross axle weight and tongue weight can be measured with platform scales found at a highway weighing station, building supply company, trucking company, junk yard, etc.

299

4RUNNER_U

2-5. Driving information

Hitch

Trailer hitch assemblies have different weight capacities. Toyota rec- ommends the use of Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight require-

ment of your vehicle.

● Follow the directions supplied by the hitch manufacturer. ● Lubricate the hitch ball with a light coating of grease. ● Remove the trailer hitch whenever you are not towing a trailer. After removing the hitch, seal any mounting hole in the vehicle body to prevent entry of any substances into the vehicle.

300

4RUNNER_U

2

2-5. Driving information

Selecting trailer ball

Use the correct trailer ball for your application.

Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers are stamped with the required trailer ball size.

Trailer class

IV

Typical trailer ball size

2 5/16 in.

II and III

2 in.

1 7/8 in.

Shank length Protrudes beyond the bottom of the lock washer and nut by at least 2 threads. Shank diameter Matches diameter size.

the ball mount hole

301

4RUNNER_U

2-5. Driving information

Positions for towing hitch receiver and hitch ball

Weight carrying ball position: 50.1 in. (1272 mm) Hitch receiver pin hole posi- tion: 43.7 in. (1109 mm)

CTH25AS026

Connecting trailer lights

Use the wire harness stored in the rear end under body.

CTH25AS011

■Service connector for towing brake controller

Your vehicle is equipped with a service connector for the trailer brake controller as shown.

CTH25AS008

302

4RUNNER_U

2

2-5. Driving information

Trailer towing tips

Your vehicle will handle differently when towing a trailer. Help to avoid an accident, death or serious injury, keep the following in mind when towing: ● Speed limits for towing a trailer vary by state or province. Do not

exceed the posted towing speed limit.

● Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest. Instability of the towing vehicle-trailer combination (trailer sway) increases as speed increases. Exceeding speed limits may cause loss of con- trol.

● Before starting out, check the trailer lights, tires and the vehicle-

trailer connections. Recheck after driving a short distance.

● Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle-trailer combination.

● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

● As stopping distance is increased when towing a trailer, vehicle-to vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

● Avoid sudden braking as you may skid, resulting in the trailer jack- knifing and a loss of vehicle control. This is especially true on wet or slippery surfaces.

303

4RUNNER_U

2-5. Driving information

● Avoid jerky starts or sudden acceleration. ● Avoid jerky steering and sharp turns, and slow down before mak-

ing turn.

● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a wider than normal turning radius.

● Slow down before making a turn, in cross winds, on wet or slippery

surfaces, etc. Increasing vehicle speed can destabilize the trailer.

● Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

● To maintain engine braking efficiency and charging system perfor- mance when using engine braking, do not put the transmission in D.

● Instability happens more frequently when descending steep or long downhill grades. Before descending, slow down and downshift. Do not make sudden downshifts while descending steep or long down- hill grades.

● Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

● Due to the added load of the trailer, your vehicle’s engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the engine coolant temperature gauge indicates overheating, immediately turn off the air condition- ing (if in use), pull your vehicle off the road and stop in a safe spot. (→P. 627)

304

4RUNNER_U

2

2-5. Driving information

STEP 2

STEP 1

● Always place wheel blocks under both the vehicle’s and the trailer’s wheels when parking. Apply the parking brake firmly, and put the transmission in P. Avoid parking on a slope, but if unavoid- able, do so only after performing the following: Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle’s and trailer’s wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into P and turn off the engine. ● When restarting after parking on a slope:

STEP 4

STEP 5

STEP 3

STEP 1

STEP 2

STEP 3

STEP 4

With the transmission in P, start the engine. Be sure to keep the brake pedal pressed. Shift into a forward gear. If reversing, shift into R. Release the parking brake and brake pedal, and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

305

4RUNNER_U

2-5. Driving information

■Matching trailer ball height to trailer coupler height

No matter which class of tow hitch applies, for a more safe trailer hookup, the trailer ball setup must be the proper height for the coupler on the trailer.

CTH25AS027

Coupler Trailer ball

CTH25AS028

■Before towing

Check that the following conditions are met: ●Ensure that your vehicle’s tires are properly inflated. (→P. 643) ●Trailer tires are inflated according to the trailer manufacturer’s recom-

mendation.

●All trailer lights work as required by law. ●All lights work each time you connect them. ●The trailer ball is set at the proper height for the coupler on the trailer. ●The vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue weight, overloading, worn suspension, or other possible causes.

●The trailer cargo is securely loaded. ●The rear view mirrors conform to all applicable federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes.

306

4RUNNER_U

2-5. Driving information

■Break-in schedule

If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km). After the vehicle has been driven for over 500 miles (800 km), you can start towing. However, for the next 500 miles (800 km), drive the vehicle at a speed of less than 45 mph (72 km/h) when towing a trailer, and avoid full throttle acceleration.

■Maintenance

●If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

●Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km) of trailer towing.

■If trailer sway occurs

One or more factors (crosswinds, passing vehicles, rough roads, etc.) can adversely affect handling of your vehicle and trailer, causing instability. ●If trailer swaying occurs:

• Firmly grip the steering wheel. Steer straight ahead.

Do not try to control trailer swaying by turning the steering wheel.

• Begin releasing the accelerator pedal immediately but very gradually to

reduce speed. Do not increase speed. Do not apply vehicle brakes.

If you make no extreme correction with the steering or brakes, your vehicle and trailer should stabilize.

307

4RUNNER_U

2-5. Driving information

●After the trailer swaying has stopped:

• Stop in a safe place. Get all occupants out of the vehicle. • Check the tires of the vehicle and the trailer. • Check the load in the trailer.

Make sure the load has not shifted. Make sure the tongue weight is appropriate, if possible.

• Check the load in the vehicle.

Make sure the vehicle is not overloaded after occupants get in.

If you cannot find any problems, the speed at which trailer swaying occurred is beyond the limit of your particular vehicle-trailer combination. Drive at a lower speed to prevent instability. Remember that swaying of the towing vehicle-trailer increases as speed increases.

CAUTION

■Trailer towing precautions

To tow a trailer safely, use extreme care and drive the vehicle in accordance with the trailer’s characteristics and operating conditions. Failure to do so could cause an accident resulting in death or serious injury. Vehicle stability and braking performance are affected by trailer stability, brake setting and performance, and the hitch. Your vehicle will handle differently when towing a trailer.

■To avoid accident or injury

●Do not exceed the TWR, unbraked TWR, GCWR, GVWR or GAWR. ●If the gross trailer weight is over 2000 lb. (907 kg), a sway control device

with sufficient capacity is required.

●Adjust the tongue weight within the appropriate range. Place heavier loads

as close to the trailer axle as possible.

●Do not exceed 65 mph (104 km/h), the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest. Slow down sufficiently before making a turn, in cross winds, on wet or slippery surface, etc. to help avoid an accident. If you experience a vehicle-trailer instability from reducing a certain speed, slow down and make sure you keep your vehicle speed under the speed of which you experience the instability.

●Do not make jerky, abrupt or sharp turns.

308

4RUNNER_U

2

2-5. Driving information

CAUTION

●Do not apply the brakes suddenly as you may skid, resulting in jackknifing and loss of vehicle control. This is especially true on wet or slippery sur- faces.

●Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue weight capacities.

●Do not use cruise control when towing. ●Slow down and downshift before descending steep or long downhill grades. Do not make sudden downshifts while descending steep or long downhill grades.

●Vehicle-trailer instability is more likely on steep long downhills. Before descending steep or long downhill grades, slow down and downshift. Do not make sudden downshifts when descending steep or long downhill grades. Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

■Hitch

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be physically capable of towing a higher weight, the operator must determine the maximum weight rating of the particular hitch assembly and never exceed the maximum weight rating specified for the trailer-hitch. Exceeding the maximum weight rating set by the trailer-hitch manufacturer can cause an accident resulting in death or serious personal injuries.

309

4RUNNER_U

2-5. Driving information

CAUTION

■When towing a trailer

Toyota recommends trailers with brakes that conform to any applicable fed- eral and state/provincial regulations. ●If the gross trailer weight exceeds unbraked TWR, trailer brakes are required. Toyota recommends trailers with brakes that conform to all appli- cable federal and state/provincial regulations.

●Never tap into your vehicle’s hydraulic system, as this will lower the vehi-

cle’s braking effectiveness.

●Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

NOTICE

■When installing a trailer hitch

Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage.

■Do not directly splice trailer lights

Do not directly splice trailer lights. Directly splicing trailer lights may damage your vehicle’s electrical system and cause a malfunction.

310

4RUNNER_U

2-5. Driving information Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

311

4RUNNER_U

3-1. Using the air conditioning system and defogger Manual air conditioning system∗

Outside/recirculated air mode button

Air outlet selector knob

Cooling and dehumidification function on/off button

Fan speed control knob

Temperature control knob

Adjusting the settings

■ Basic setting

STEP 1

To turn on the air conditioning system and adjust the fan speed, turn the fan speed control knob clockwise (increase) or counterclockwise (decrease). Turning the knob to “OFF” turns off the fan.

∗: If equipped

314

4RUNNER_U

3-1. Using the air conditioning system and defogger

STEP 2

To adjust the temperature setting, turn the temperature control knob clockwise (warm) or counterclockwise (cool).

is not pressed, the system will blow ambient temperature

If air or heated air. For quick cooling, turn the temperature control knob to “MAX A/C”. The air conditioning will automatically turn on and, if an air outlet position other than is selected, the system will be set to recirculated air mode. While “MAX A/C” is selected, it is not possible to turn off the air conditioning. To select the air outlets, set the air outlet selector knob to the desired position. The positions between the air outlet selections shown below can also be selected for more delicate adjustment.

or

Air flows to the upper body.

Air flows to the upper body and feet.

CTH31AS004

CTH31AS005

315

STEP 3

4RUNNER_U

3-1. Using the air conditioning system and defogger

Air flows to the feet.

CTH31AS006

CTH31AS007

CTH31AS008

Air flows to the feet and the windshield defogger operates.

The air intake is automatically switched to outside air mode.

Pressing to turn the cool- ing and dehumidification function on clears the windshield and side windows faster.

Air flows to the windshield and side windows.

The air intake is automatically switched to outside air mode. It is not possible to return to recircu- lated air mode when the switch is on.

Pressing to turn the cool- ing and dehumidification function on clears the windshield and side windows faster.

316

4RUNNER_U

3-1. Using the air conditioning system and defogger

■ Switching between outside air and recirculated air modes

Press

The mode switches between outside air mode (introduces air from out- side the vehicle) (indicator off) and recirculated air mode (recycles air inside the vehicle) (indicator on) each time the button is pressed.

Adjusting the position of and opening and closing the air outlets

Front center outlets

Front side outlets

CTH31AS022

CTH31AS015

Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.

Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.

317

4RUNNER_U

3-1. Using the air conditioning system and defogger

Rear outlets

Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.

CTH31AS016

■Using the system in recirculated air mode

The windows will fog up more easily if recirculated air mode is used for an extended period of time.

■Switching between outside air and recirculated air modes

Recirculated air mode or outside air mode may be automatically switched to in accordance with the outside temperature, etc.

■When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the temperature setting.

■When the indicator light on

flashes

Press to turn off the cooling and dehumidification function and turn it on again. There may be a problem in the air conditioning system if the indi- cator light continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer.

■When outside air temperature is below 32°F (0°C)

The cooling and dehumidification function may not operate even when

is pressed.

318

4RUNNER_U

3-1. Using the air conditioning system and defogger

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off.

CAUTION

■To prevent the windshield from fogging up

Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the wind- shield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is stopped.

319

4RUNNER_U

3-1. Using the air conditioning system and defogger Automatic air conditioning system∗

Air outlets and fan speed are automatically adjusted according to the temperature setting.

Driver's side temperature control dial

Cooling and dehumidification function on/off button

Fan speed display

Air outlet display Driver’s side temperature display

Passenger’s side temperature display

Passenger’s side temperature control dial

Automatic mode button

Air outlet selector buttons

Dual mode button

“Off” button Windshield defogger button Outside/recirculated air mode button

Fan speed control button

∗: If equipped

320

4RUNNER_U

3-1. Using the air conditioning system and defogger

Using the automatic air conditioning system

STEP 1

Press

The air conditioning system begins to operate. Air outlets and fan speed are automatically adjusted according to the temperature set- ting.

STEP 2

Turn

clockwise to increases the temperature and turn

counterclockwise to decreases the temperature on the

driver’s side.

is pressed (the indicator on

When is on) or the pas- senger’s side temperature control dial is turned, the temperature for the driver and passenger seats can be adjusted separately.

321

4RUNNER_U

3-1. Using the air conditioning system and defogger

Adjusting the settings manually

■ Basic setting

STEP 1

To turn on the air conditioning system and adjust the fan speed, press “>” on to increase the fan speed and “<” to decrease the fan speed. to turn the fan off. Press

STEP 2

To adjust the temperature setting, turn

clockwise to

increases the temperature and turn to decreases the temperature.

counterclockwise

is pressed (the indicator on

When is on) or the pas- senger’s side temperature control dial is turned, the temperature for the driver and passenger seats can be adjusted separately. To change the air outlets, press

or

STEP 3

The air flow shown on the display indicates the following:

Air flows to the upper body.

CTH31AS009

: May occur in automatic mode

322

4RUNNER_U

3-1. Using the air conditioning system and defogger

Air flows to the upper body and feet.

CTH31AS010

Air flows to the feet.

Air flows to the feet and the windshield defogger operates.

The air intake is automatically switched to outside air mode.

CTH31AS011

CTH31AS012

323

4RUNNER_U

3-1. Using the air conditioning system and defogger

■ Switching between outside air and recirculated air modes

Press

The mode switches between outside air mode (the indicator is off) and recirculated air mode (the indicator is on) each time the button is pressed.

Defogging the windshield

Defogging

The air conditioning system oper- ates automatically. The air intake is automatically switched to outside air mode. It is not possible to return to recircu- lated air mode when the switch is on.

CTH31AS013

324

4RUNNER_U

3-1. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Front center outlets

Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.

Front side outlets

CTH31AS014

Rear outlets

CTH31AS015

Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.

Direct air flow to the left or right, up or down. Turn the knob to open or close the vent.

CTH31AS016

325

4RUNNER_U

3-1. Using the air conditioning system and defogger

■Using automatic mode

Fan speed is adjusted automatically according to the temperature setting and ambient conditions. As a result, the following may occur: ●The system may switch automatically to recirculated air mode when the coolest temperature setting is selected when the ambient temperature is high.

●Immediately after the switch is pressed, the fan may stop for a while until

warm or cool air is ready to flow.

●Cool air may flow to the area around the upper body when the heater is

on.

■Switching between outside air and recirculated air modes

Recirculated air mode or outside air mode may be automatically switched to in accordance with the temperature setting, the outside temperature, etc.

■Using the system in recirculated air mode

The windows will fog up more easily if recirculated air mode is used.

■Window defogger feature

Recirculated air mode may automatically switch to outside air mode in situa- tions where the windows need to be defogged.

■When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the temperature setting.

■When driving on dusty roads

Close all windows. If dust thrown up by the vehicle is still drawn into the vehi- cle after closing the windows, it is recommended that the air intake mode be set to outside air mode and the fan speed to any setting except off.

326

4RUNNER_U

3-1. Using the air conditioning system and defogger

■When outside air temperature is below 32°F (0°C)

The cooling and dehumidification function may not operate even when

is pressed.

■When the indicator light on

flashes

to turn off the cooling and dehumidification function and turn it Press on again. There may be a problem in the air conditioning system if the indi- cator light continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer.

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

• It is recommended that the air conditioning system be set to outside air

mode prior to turning the vehicle off.

• The start timing of the blower may be delayed for a short period of time immediately after the air conditioning system is started in automatic mode.

CAUTION

■To prevent the windshield from fogging up

during cool air operation in extremely humid weather. The Do not use difference between the temperature of the outside air and that of the wind- shield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is stopped.

327

4RUNNER_U

3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers

Defoggers are used to defog the rear window, and to remove rain- drops, dew and frost from the outside rear view mirrors. Before operating the defoggers, make sure the back window is completely closed. (→P. 101) Vehicles with a manual air conditioning system

Turns the defoggers on/off

The defoggers will automati- cally turn off after their opera- tion time. The operation time varies depending on the ambi- ent temperature and vehicle speed.

Vehicles with an automatic air conditioning system

Turns the defoggers on/off

The defoggers will automati- cally turn off after their opera- tion time. The operation time varies depending on the ambi- ent temperature and vehicle speed.

328

4RUNNER_U

3-1. Using the air conditioning system and defogger

■The defoggers can be operated when

●Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode.

●The back window is completely closed. ■The outside rear view mirror defoggers

Turning the rear window defogger on will turn the outside rear view mirror defoggers on.

CAUTION

■When the outside rear view mirror defoggers are on

Do not touch outside surface of the rear view mirrors, as they can become very hot and burn you.

329

4RUNNER_U

3-1. Using the air conditioning system and defogger Windshield wiper de-icer∗

This feature is used to prevent ice from building up on the wind- shield and wiper blades.

Turns the windshield wiper de- icer on/off

The windshield wiper de-icer will automatically turn off after approximately 15 minutes.

CTH31AS020

■The windshield wiper de-icer can be operated when

Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is in IGNITION ON mode.

CAUTION

■When the windshield wiper de-icer is on

Do not touch the lower part of the windshield or the side of the front pillars, as the surfaces can become very hot and burn you.

∗: If equipped

330

4RUNNER_U

3-2. Using the audio system Audio system types

Without navigation system and Display Audio system Type A: CD player with changer controller and AM/FM radio

Type B: CD player with changer controller and AM/FM radio

331

4RUNNER_U

3-2. Using the audio system

Type C: CD player with changer and AM/FM radio

Title

Using the radio Using the CD player Playing MP3 and WMA discs Operating an iPod Operating a USB memory Optimal use of the audio system Using the AUX port Using the steering wheel audio switches

Page P. 338
P. 345
P. 354
P. 362
P. 369
P. 376
P. 381
P. 382

332

4RUNNER_U

3-2. Using the audio system

With Display Audio system Owners of models equipped with a Display Audio system should refer to the “Display Audio System Owner's Manual”.

With navigation system Owners of models equipped with a navigation system should refer to the “Navigation System Owner's Manual”.

333

4RUNNER_U

3-2. Using the audio system

Language settings (type B and C)

The language used for all voice guidance, voice recognition and mes- sages may be changed.

STEP 1

STEP 2

STEP 3

STEP 4

(MORE). (LANG). or

Press Press Press Press guage. For vehicles sold in the U.S.A.

as corresponds to the desired lan-

“ENG” (English) or “ESP” (Spanish)

For vehicles sold in Canada

“ENG” (English) or “FRAN” (French)

■Using cellular phones

Interference may be heard through the audio system's speakers if a cellular phone is being used inside or close to the vehicle while the audio system is operating.

■About Bluetooth®

The Bluetooth wordmark and logo are owned by Bluetooth SIG. and permis- sion has been granted to use the trademark of the licensee Panasonic Cor- poration. Other trademarks and trade names are owned by various different owners.

334

4RUNNER_U

3-2. Using the audio system

■Certification

For the Display Audio system FCC ID: AJDK032
IC ID: 775E-K032
For the Display Audio system and the audio system NOTE: This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undes- ired operation of this device. Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. The antenna for Bluetooth cannot be removed (or replaced) by user. L'antenne de Bluetooth ne peut pas être supprimé (ou remplacé) par l'utili- sateur. This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. Cet appareil est conforme au CNR-310 d'Industrie Canada. Son exploitation est autorisée sous réserve que l'appareil ne cause pas de brouillage préjudi- ciable. FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

335

4RUNNER_U

3-2. Using the audio system

CAUTION: This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Expo- sure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio fre- quency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles). Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d’exposition dans le Sup- plément C à OET65 et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une dis- tance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités: mains, poignets, pieds et chevilles). NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ●Reorient or relocate the receiving antenna. ●Increase the separation between the equipment and receiver. ●Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

336

4RUNNER_U

3-2. Using the audio system

Co-location: This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

CAUTION

■For vehicles sold in the U.S.A. and Canada

●Part 15 of the FCC Rules and RSS-Gen of the IC Rules

FCC Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

●Laser products

• Do not take this unit apart or attempt to make any changes yourself.

This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disas- semble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.

• This product utilizes a laser.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation expo- sure.

• The use of optical instruments with this product will increase eye haz-

ard.

NOTICE

■To prevent battery discharge

Do not leave the audio system on longer than necessary with the engine off.

■To avoid damaging the audio system

Take care not to spill drinks or other fluids over the audio system.

337

4RUNNER_U

3-2. Using the audio system Using the radio

Type A

Power

Volume

Seeking a frequency

Station selector

Adjusting the frequency (AM, FM mode) or channel (SAT mode)

Scanning for receivable stations

AM⋅SAT/FM mode buttons

Displaying radio text messages

Changing the channel category

Type B and C

Power

Volume

Seeking a frequency

Adjusting the frequency (AM, FM mode) or channel (SAT mode)

Station selector

Scanning for receivable stations

AM/FM/SAT mode button

Displaying radio text messages

Setting preset buttons

Mute

Changing the channel category

338

4RUNNER_U

3-2. Using the audio system

Setting station presets (excluding XM® Satellite Radio)

STEP 1

Search for desired stations by turning

or

or

pressing “∧” or “∨” on

STEP 2

Press and hold a button (from a beep. Type B and C: Each time changed. There are a total of 6 pages.

to

) until you hear

is pressed, station pages are

Scanning radio stations (excluding XM® Satellite Radio)

■ Scanning the preset radio stations

STEP 1

STEP 2

Press and hold Preset stations will be played for 5 seconds each. When the desired station is reached, press

until you hear a beep.

■ Scanning all radio stations within range