2009 Toyota 4runner Owners Manual

it

Lock mode allows the seat belt to retract only.

While pushing the child seat into the rear seat, allow the shoulder belt to retract until the child seat is securely in place.

After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor. (→P. 126)

124

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 125 Wednesday, July 30, 2008 3:00 PM

n Booster seat

1-7. Safety information

Place the booster seat on the seat facing the front of the vehi- cle.

Sit the child in the booster seat. Fit the seat belt to the booster seat according to the manufac- turer’s instructions and insert the plate into the buckle. Make sure that the belt is not twisted.

Check that the shoulder belt is correctly positioned over the child’s shoulder, and that the lap belt is as low as possible. (→P. 63)

Removing a child restraint installed with a seat belt

Push the buckle release button and fully retract the seat belt.

125

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 126 Wednesday, July 30, 2008 3:00 PM

1-7. Safety information

Child restraint systems with a top tether strap

Secure the child restraint using the LATCH anchors or seat belt, and remove the head restraint.

Vehicles without third seats

Raise the anchor bracket, latch the hook onto the anchor bracket and tighten the top tether strap.

Make sure the top tether strap is securely latched. Hook Top tether strap Anchor bracket

126

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 127 Wednesday, July 30, 2008 3:00 PM

Vehicles with third seats

1-7. Safety information

Open the anchor bracket cover, latch the hook onto the anchor bracket and tighten the top tether strap.

Make sure the top tether strap is securely latched. Hook Top tether strap Anchor bracket

Reinstall the head restraint.

127

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 128 Wednesday, July 30, 2008 3:00 PM

1-7. Safety information

n Laws and regulations pertaining to anchorages

The LATCH system conforms to FMVSS225 or CMVSS210.2. Child restraint systems conforming to FMVSS213 or CMVSS213 specifica- tions can be used. This vehicle is designed to conform to the SAE J1819.

n When the anchor bracket is not in use (vehicles without third seats)

Lower the anchor bracket.

The anchor bracket is only designed to secure the top tether strap. Do not use the anchor bracket for any other purpose.

128

4RUNNER_U_(L/O_0808)

1

4RUNNER_U.book Page 129 Wednesday, July 30, 2008 3:00 PM

1-7. Safety information

CAUTION

n When installing a booster seat

Do not fully extend the shoulder belt to prevent the belt from going to ALR lock mode. (→P. 65) ALR mode causes the belt to tighten only which could cause injury or dis- comfort to the child.

n When installing a child restraint system

Follow the directions given in the child restraint system installation manual and fix the child restraint system securely in place. If the child restraint system is not correctly fixed in place, the child or other passengers may be seriously injured or even killed in the event of sudden braking or an accident.

If the driver’s seat interferes with the child restraint system and prevents it from being attached correctly, attach the child restraint system to the right- hand rear seat.

l Adjust the front passenger seat so that it does not interfere with the child restraint system.

l Only put a forward-facing or booster child seat on the front seat when unavoidable. When installing a forward- facing or booster child seat on the front passenger seat, move the seat as far back as possible even if the AIR BAG OFF indicator light is illuminated. Fail- ing to do so may result in death or seri- ous injury if the airbags deploy (inflate).

l Vehicles with third seats: When installing a child restraint system in the second center position, adjust both seatbacks at the same angle. Other- wise, the child restraint system cannot be securely restrained and this may cause death or serious injuries in an accident.

129

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 130 Wednesday, July 30, 2008 3:00 PM

1-7. Safety information

CAUTION

n When installing a child restraint system

l When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder. Failing to do so may result in death or serious injury in the event of an accident or sudden braking.

l Ensure that the belt and tab are securely locked and the seat belt is not

twisted.

l Push and pull the child restraint system from side to side and forward to be

sure it is secure.

l After securing a child restraint system, never adjust the seat. l Follow all installation instructions provided by the child restraint system

manufacturer.

n Do not use a seat belt extender

If a seat belt extender is used when installing a child restraint system, the seat belt will not securely hold the child restraint system, which could cause death or serious injury to the child or other passengers in the event of an accident.

n To correctly attach a child restraint system to the anchors

l When using the LATCH anchors, be sure that there are no foreign objects around the anchors and that the seat belt is not caught behind the child restraint. Make sure the child restraint system is securely attached, or it may cause death or serious injury to the child or other passengers in the event of a sudden stop or accident.

l Vehicles with third seats: When using the left side LATCH anchors for the child restraint system, do not sit in the center seat. Seat belt function may be impaired, such as being positioned overly high or loose-fitting, which may result in death or serious injury in the event of sudden braking or an accident.

130

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 132 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures Driving the vehicle

The following procedures should be observed to ensure safe driv- ing. n Starting the engine (→P. 140) n Driving

With the brake pedal depressed, shift the shift lever to D.

Release the parking brake.

(→P. 143) (→P. 146) Gradually release the brake pedal and gently depress the accelerator pedal to accelerate the vehicle.

n Stopping

With the shift lever in D, depress the brake pedal. If necessary, set the parking brake. When the vehicle is stopped for an extended period of time, shift (→P. 143) the shift lever to P or N.

n Parking the vehicle

With the shift lever in D, depress the brake pedal. Set the parking brake. Shift the shift lever to P. When parking on a hill, if necessary, block the wheels. Turn the engine switch off to stop the engine. Lock the door, making sure that you have the key on your person.

(→P. 146) (→P. 143)

Starting on a steep uphill

With the brake pedal depressed, firmly set the parking brake and shift the shift lever to D. Gently depress the accelerator pedal. Release the parking brake.

132

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 133 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures

n Driving in the rain

l Drive carefully when it is raining, because visibility will be reduced, the

windows may become fogged-up, and the road will be slippery.

l Drive carefully when it starts to rain, because the road surface will be

especially slippery.

l Refrain from high speeds when driving on an expressway in the rain, because there may be a layer of water between the tires and the road surface, preventing the steering and brakes from operating properly.

n Breaking in your new Toyota

To extend the life of the vehicle, the following precautions are recommended to observe: l For the first 200 miles (300 km):

Avoid sudden stops.

l For the first 500 miles (800 km):

Do not tow a trailer.

l For the first 1000 miles (1600 km):

• Do not drive at extremely high speeds. • Avoid sudden acceleration. • Do not drive continuously in the low gears. • Do not drive at a constant speed for extended periods.

n Drum-in disc type parking brake system

Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down.

n Operating your vehicle in a foreign country

Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (→P. 473)

n Normal characteristics after turning off the engine

Approximately five hours after the engine is turned off, you may hear sound coming from under the vehicle for several minutes. This is the sound of a fuel evaporation leakage check and, it does not indicate a malfunction.

133

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 134 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures

CAUTION

n When starting the vehicle

Always keep your foot on the brake pedal while stopped with the engine run- ning. This prevents the vehicle from creeping.

n When driving the vehicle

l Do not drive if you are unfamiliar with the location of the brake and accel-

erator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake pedal will result in sudden acceleration that may lead to an accident that could result in death or serious injury.

• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly, allowing you to depress the brake and accelerator pedals properly.

• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.

l Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. This may cause a fire if there is any flammable material nearby.

l Do not let the vehicle roll backwards while the shift lever is in a driving

position, or roll forward while the shift lever is in R. Doing so may cause the engine to stall or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle. If the smell of exhaust is noticed inside the vehicle, open the windows and check that the back door and back window are closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immediately.

l Do not under any circumstances shift the shift lever to P, R or N while the

vehicle is moving. Doing so can cause significant damage to the transmission system and may result in a loss of vehicle control.

134

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 135 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures

CAUTION

n When driving the vehicle

l Do not shift the shift lever to N while the vehicle is moving.

Doing so may cause the engine brake to not operate properly and lead to an accident.

l Do not turn the engine off while driving.

The power steering and brake booster systems will not operate properly if the engine is not running.

l Use engine braking (downshift) to maintain a safe speed when driving

down a steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (→P. 144)

l When stopped on an inclined surface, use the brake pedal and parking brake to prevent the vehicle from rolling backward or forward and causing an accident.

l Do not adjust the position of the steering wheel, the seat, or the inside or

outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents that may result in death or serious injury.

l Always check that all passengers’ arms, heads or other parts of their bod- ies are not outside the vehicle, as this may result in death or serious injury. l Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires. Driving over 85 mph (140 km/h) may result in tire failure, loss of control and possible injury. Be sure to consult a tire dealer to determine whether the tires on your vehicle are high-speed capability tires or not before driving at such speeds. n When driving on slippery road surfaces

l Sudden braking, acceleration and steering may cause tire slippage and

reduce your ability to control the vehicle, resulting in an accident.

l Sudden changes in engine speed, such as engine braking caused by up- shifting or down-shifting, may cause the vehicle to skid, resulting in an accident.

135

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 136 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures

CAUTION

n When driving on slippery road surfaces

l After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.

n When shifting the shift lever

Be careful not to shift the shift lever with the accelerator pedal depressed. This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

n When the vehicle is stopped

l Do not race the engine.

If the vehicle is in any gear other than P or N, the vehicle may accelerate suddenly and unexpectedly, and may cause an accident.

l Do not leave the vehicle with the engine running for a long time.

If such a situation cannot be avoided, park the vehicle in an open space and check that exhaust fumes do not enter the vehicle interior.

l Always keep a foot on the brake pedal while the engine is running to pre-

vent an accident caused by the vehicle moving.

n When the vehicle is parked

l Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in

the vehicle when it is in the sun. Doing so may result in the following. • Gas may leak from a cigarette lighter or spray can, and may lead to a

fire.

• The temperature inside the vehicle may cause the plastic lenses and

plastic material of eye glasses to deform or crack.

• Soft drink cans may fracture, causing the contents to spray over the interior of the vehicle, and may also cause a short circuit in the vehi- cle’s electrical components.

l Always apply the parking brake, shift the shift lever to P, stop the engine

and lock the vehicle. Do not leave the vehicle unattended while the engine is running.

136

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 137 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures

CAUTION

n When the vehicle is parked

l Do not touch the exhaust pipe while the engine is running or immediately

after turning the engine off. Doing so may cause burns.

l Do not leave the engine running in an area with snow build-up, or where it is snowing. If snowbanks build up around the vehicle while the engine is running, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

n Exhaust gases

Exhaust gases include harmful carbon monoxide (CO) that is colorless and odorless. Inhaling exhaust gases may lead to death or a serious health haz- ard.

If the vehicle is in a poorly ventilated area, stop the engine. In a closed area, such as a garage, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

l The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard. n When taking a nap in the vehicle

Always turn the engine off. Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.

n When braking the vehicle

l When the brakes are wet, drive more cautiously.

Braking distance increases when the brakes are wet, and may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle.

137

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 138 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures

CAUTION

n When braking the vehicle

If the power brake assist function does not operate, do not follow other vehicles closely and avoid downhills or sharp turns that require braking. In this case, braking is still possible, but it will require more force on the pedal than usual. Braking distance may also increase.

l Do not pump the brake pedal if the engine stalls.

Each push on the brake pedal uses up the reserve for the power-assisted brakes.

l The brake system consists of 2 individual hydraulic systems: If one of the systems fails, the other will still operate. In this case, the brake pedal should be depressed more firmly than usual and braking distance becomes longer. Do not drive your vehicle with only a single brake system. Have your brakes fixed immediately.

NOTICE

n When driving the vehicle

Do not use the accelerator pedal or depress accelerator and brake pedals together to hold the vehicle on a hill.

n When parking the vehicle

Always put the shift lever in P. Failure to do so may cause the vehicle to move or the vehicle may acceler- ate suddenly if the accelerator pedal is accidentally depressed.

n Avoiding damage to vehicle parts

l Do not turn the steering wheel fully in either direction and hold it there for a

long time. Doing so may damage the power steering pump.

l When driving over bumps in the road, drive as slowly as possible to avoid

damaging the wheels, underside of the vehicle, etc.

138

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 139 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures

NOTICE

n If you hear a squealing or scraping noise while driving (brake pad wear

limit indicators) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. The rotor damage can result if the pads are not replaced when needed. It is dangerous to drive the vehicle when the wear limits of the brake pads and/or that of the brake discs are exceeded.

n If you get a flat tire while driving

A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually press the brake pedal to slow down the vehicle. It may be difficult to control your vehicle. l The vehicle will make abnormal sounds. l The vehicle will behave abnormally. Replace a flat tire with a new one. (→P. 448)

n When encountering flooded roads

Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle. l Engine stalling l Short in electrical components l Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. l Brake function l Changes in quantity and quality of oil and fluid used for the engine, trans-

mission, transfer (4WD models), differentials, etc.

l Lubricant condition for the propeller shaft, bearings and suspension joints

(where possible) and the function of all joints, bearings, etc.

139

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 140 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures Engine (ignition) switch

n Engine switch

LOCK The steering wheel is locked and the key can be removed. (The key can be removed only when the shift lever is in P.) ACC Some electrical components such as the audio system can be used. ON All electrical components can be used. START For starting the engine.

n Starting the engine

Check that the parking brake is set. Check that the shift lever is set in P. Sit in the driver’s seat and firmly depress the brake pedal. Turn the engine switch to the START position and start the engine. The engine will crank until it starts or for up to 25 seconds, which- ever is less. If you turn the engine switch, the engine will keep cranking for about 30 seconds maximum. Continue depressing the brake pedal until the engine is com- pletely started.

140

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 141 Wednesday, July 30, 2008 3:00 PM

n Turning the key from ACC to LOCK

2-1. Driving procedures

Shift the shift lever to P. (→P. 143) Push in the key and turn to the LOCK position.

n Steering lock release

When starting the engine, the engine switch may seem stuck in the LOCK posi- tion. To free it, turn the key while turning the steering wheel slightly in either direc- tion.

n If the engine does not start

The engine immobilizer system may not have been deactivated. (→P. 88)

n Key reminder function

A buzzer sounds if the driver’s door is opened, while the engine switch is in the ACC or LOCK position to remind you to remove the key.

CAUTION

n When starting the engine

Always start the engine while sitting in the driver’s seat. Do not depress the accelerator while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

141

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 142 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures

CAUTION

n Caution while driving

Do not turn the engine switch to the LOCK position. If in an emergency, you must turn the engine off while the vehicle is moving, turn the engine switch only to the ACC position.

NOTICE

n To prevent battery discharge

Do not leave the engine switch in the ACC or ON position for long periods if the engine is not running. n When starting the engine

l Do not crank for more than 30 seconds at a time. This may overheat the

starter and wiring systems. l Do not race a cold engine.

If the engine becomes difficult to start or stalls frequently, have the engine checked immediately.

142

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 143 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures Automatic Transmission

Select a shift position appropriate for the driving conditions. n Shifting the shift lever

While the engine switch is on, depress the brake pedal and

move the shift lever. n Shift position uses

Shift position

Function

3, 2

Parking the vehicle or starting the engine

Reversing Neutral

Normal driving*

Position for engine braking

Position for more powerful engine braking

Position for maximum engine braking

*: To improve fuel consumption and reduce noises, set the shift lever in

D for normal driving.

143

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 144 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures

n Downshifting restrictions

The shift lever cannot be downshifted if the following speeds are exceeded.

2WD models

Downshifting

4 → 3
3 → 2
2 → L

4WD models

Maximum speed

4.0 L V6 (1GR-FE) engine

4.7 L V8 (2UZ-FE) engine

mph (km/h)

82 (133) 55 (90) 24 (39)

86 (139) 58 (94) 25 (40)

Downshifting Transfer position

4 → 3

3 → 2

2 → L

H2 and H4

L4

H2 and H4

L4

H2 and H4

L4

mph (km/h)

Maximum speed

4.0 L V6 (1GR-FE)

engine 82 (133) 31 (51) 55 (90) 21 (35) 24 (39) 9 (15)

4.7 L V8 (2UZ-FE)

engine 86 (139) 34 (54) 58 (94) 22 (36) 25 (40) 9 (15)

n When driving with the cruise control system

The engine brake will not operate when downshifting from D to 4.(→P. 166)

n If the shift lever cannot be shifted from P (→P. 457)

144

4RUNNER_U_(L/O_0808)

2

4RUNNER_U.book Page 145 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures Turn signal lever

Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change. The left hand signal will flash until you release the lever.

n Turn signals can be operated when

The engine switch is in the ON position.

n If the indicators flash faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

145

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 146 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures Parking brake

Set the parking brake*. (Depressing the pedal again releases the parking brake.)

At this time, the indicator will come on. *: Fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot.

n Parking brake engaged warning buzzer

The buzzer sounds to indicate that parking brake is still engaged (with the vehicle having reached a speed of 3 mph [5 km/h]).

NOTICE

n Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

146

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 147 Wednesday, July 30, 2008 3:00 PM

2-1. Driving procedures Horn

To sound the horn, press on or close to the

mark.

n After adjusting the steering wheel

Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P. 69)

147

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 148 Wednesday, July 30, 2008 3:00 PM

2-2. Instrument cluster Gauges and meters

The following gauges, meters and displays illuminate when the engine switch is in the ON position.

Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Engine coolant temperature gauge Displays the engine coolant temperature. Odometer/trip meter switching and trip meter resetting button Switches between odometer and trip meter displays. Pushing and hold- ing the button will reset the trip meter when the trip meter is being dis- played.

148

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 149 Wednesday, July 30, 2008 3:00 PM

2-2. Instrument cluster

Odometer/trip meter Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display differ- ent distances independently.

Odometer and trip meter display button

Pressing this button switches between odometer and trip meter dis- plays.

Odometer Trip meter A* Trip meter B* *:Pushing and holding the button will reset the trip meter.

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Brighter Darker

149

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 150 Wednesday, July 30, 2008 3:00 PM

2-2. Instrument cluster

NOTICE

n To prevent damage to the engine and its components

l Do not let the indicator needle of the tachometer enter the red zone, which

indicates the maximum engine speed.

l The engine may be overheating if the temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 463)

150

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 151 Wednesday, July 30, 2008 3:00 PM

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.

Instrument cluster (type A)

Instrument cluster (type B)

151

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 152 Wednesday, July 30, 2008 3:00 PM

2-2. Instrument cluster

Instrument cluster (type C)

Center panel

152

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 153 Wednesday, July 30, 2008 3:00 PM

2-2. Instrument cluster

n Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

Slip indicator (→P. 175, 183, 189)

VSC OFF indicator (→P. 179, 191)

Active traction control indicator (→P. 182)

AUTO LSD indicator (→P. 175, 190)

Four-wheel drive indicator(→P. 177)

Center differential lock indicator (→P. 179)

4LO indicator (→P. 177)

Rear differential lock indicator (→P. 184)

Downhill assist control indicator (→P. 186)

(if equipped)

(if equipped)

(4WD models)

(4WD models)

(if equipped)

(if equipped)

153

(U.S.A.)

(Canada)

(if equipped)

Turn signal indicator (→P. 145)

Headlight high beam indicator (→P. 159)

Headlight indicator (→P. 158)

Tail light indicator (→P. 158)

Front fog light indicator (→P. 162)

Security indicator (→P. 88)

Shift position and shift range indicators (→P. 143)

Cruise control indicator

(→P. 166)

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 154 Wednesday, July 30, 2008 3:00 PM

2-2. Instrument cluster

Height control indicators (→P. 169)

RSCA OFF indicator (→P. 107)

AIR BAG ON indicator (→P. 108)

AIR BAG OFF indicator (→P. 108)

n Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 436)

(U.S.A.)

(Canada)

(U.S.A.)

(Canada)

*: These lights turn on when the engine switch is turned to the ON position to indicate that a system check is being performed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.

CAUTION

n If a safety system warning light does not come on

Should a safety system light such as ABS and the SRS airbag warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

154

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 155 Wednesday, July 30, 2008 3:00 PM

2-2. Instrument cluster Accessory meter

RESET button MODE button Trip information display (air conditioning system without DUAL button) Displays the trip information. (→P. 156) Outside temperature and trip information display (air condition- ing system with DUAL button) Displays the outside temperature and trip information. (→P. 156, 326) Clock (→P. 325) Outside temperature display (air conditioning system without DUAL button) Displays the outside air temperature. (→P. 326) :00 button (→P. 325) M (Minute) button (→P. 325) H (Hour) button (→P. 325)

155

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 156 Wednesday, July 30, 2008 3:00 PM

2-2. Instrument cluster

Outside temperature and trip information display (if equipped)

Every time the MODE button is pushed, the display toggles through these information. l OUTSIDE (outside temperature display)

Displays the outside air temperature.

The temperature range that can be displayed is from -22°F (-30°C) to 122 °F (50°C).

l RANGE (driving range)

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining.

• The distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may dif- fer from that displayed.

• When only a small amount of fuel is added to the tank, the display may not be updated.

l AVG. (average fuel consumption)

Displays the average fuel consumption since the engine was started or since the function was reset. The function can be reset by pressing the RESET button for longer than 1 second when the average fuel consumption is displayed.

l AVG. (average vehicle speed)

Displays the average vehicle speed since the engine was started or since the function was reset. The function can be reset by pressing the RESET button for longer than 1 second when the average vehicle speed is displayed.

156

4RUNNER_U_(L/O_0808)

2

4RUNNER_U.book Page 157 Wednesday, July 30, 2008 3:00 PM

2-2. Instrument cluster

l Display off

CAUTION

n Caution while driving

Do not adjust the display. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury.

157

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 158 Wednesday, July 30, 2008 3:00 PM

2-3. Operating the lights and wipers Headlight switch

The headlights can be operated manually or automatically.

Vehicles without automatic light control system

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on.

U.S.A. Canada

158

4RUNNER_U_(L/O_0808)

2

4RUNNER_U.book Page 159 Wednesday, July 30, 2008 3:00 PM

2-3. Operating the lights and wipers

Vehicles with automatic light control system

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. The headlights and all lights listed above turn on and off automati- cally. the engine switch is in the ON position)

(When

U.S.A.

Canada

Turning on the high beam headlights

With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release the lever to turn them off. You can flash the high beams with the headlights on or off.

159

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 160 Wednesday, July 30, 2008 3:00 PM

2-3. Operating the lights and wipers

n Daytime running light system (if equipped)

To make your vehicle more visible to other drivers, the headlights turn on automatically (at a reduced intensity) whenever the engine is started and the parking brake is released. Daytime running lights are not designed for use at night.

n Headlight control sensor

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the automatic headlight sys- tem to malfunction.

interferes with

n Automatic light off system

l When the headlights come on: The headlights and tail lights turn off 30
seconds after all doors are closed with the engine switch turned to the ACC or LOCK position. (The lights turn off immediately if the LOCK but- ton on the wireless remote control is pressed twice after all doors are locked.)

l When only the tail lights come on: The tail lights turn off automatically with the engine switch turned to the ACC or LOCK position and the driver’s door is opened.

If the driver’s door is kept open, the lights automatically turn off after 30 min- utes. To turn the lights on again, turn the engine switch to the ON position, or turn the headlight switch off once and then back to the

or n Customization that can be configured at Toyota dealer

position.

Settings (e.g. light sensor sensitivity) can be changed. (Customizable features →P. 495)

160

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 161 Wednesday, July 30, 2008 3:00 PM

2-3. Operating the lights and wipers

NOTICE

n To prevent battery discharge

Do not leave the lights on longer than necessary when the engine is not run- ning.

161

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 162 Wednesday, July 30, 2008 3:00 PM

2-3. Operating the lights and wipers Fog light switch (if equipped)

The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam.

OFF Front fog lights ON

162

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 163 Wednesday, July 30, 2008 3:00 PM

2-3. Operating the lights and wipers Windshield wipers and washer

Wiper intervals can be adjusted for intermittent operation (when INT is selected.)

windshield

Intermittent wiper operation Low speed windshield wiper operation High wiper operation

speed windshield

Decreases the intermittent windshield wiper frequency Increases intermittent windshield wiper frequency

the

163

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 164 Wednesday, July 30, 2008 3:00 PM

2-3. Operating the lights and wipers

Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts.

n The windshield wiper and washer can be operated when

The engine switch must be in the ON position.

n If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

n When the windshield is dry

Do not use the wipers, as they may damage the windshield.

n When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually. n When a nozzle becomes block

Do not try to clear it with a pin or other object. The nozzle will be damaged.

164

4RUNNER_U_(L/O_0808)

2

4RUNNER_U.book Page 165 Wednesday, July 30, 2008 3:00 PM

2-3. Operating the lights and wipers Rear window wiper and washer

Intermittent window wiper operation. Normal window wiper oper- ation Washer/wiper dual opera- tion Washer/wiper dual opera- tion The rear window wiper oper- ates while the washer squirts.

n The rear window wiper and washer can be operated when

l The engine switch must be in the ON position. l The back window is fully closed.

NOTICE

n When the rear window is dry

Do not use the wipers, as they may damage the rear window.

n When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the knob is continuously twisted upward or downward as far as it will go.

165

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 166 Wednesday, July 30, 2008 3:00 PM

2-4. Using other driving systems Cruise control

Use cruise control to maintain a set speed without using the acceler- ator.

Indicator Cruise control switch

n Set the vehicle speed

Press the ON-OFF button to turn the cruise control on.

At this time, the cruise control indicator will come on. Press the button once more to deactivate the cruise control.

Accelerate or decelerate to the desired speed and push the lever down to set the cruise control speed.

166

4RUNNER_U_(L/O_0808)

2

4RUNNER_U.book Page 167 Wednesday, July 30, 2008 3:00 PM

n Adjusting the speed setting

2-4. Using other driving systems

Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pushing the lever up or down and releasing it.

n Canceling and resuming regular acceleration

Cancel Pull the lever towards you to cancel cruise control. The speed setting is also can- celed when the brakes are applied. Resume To resume cruise control and return to the set speed, push the lever up.

n Cruise control can be set when

l The shift lever is in D or 4. l Vehicle speed is more than approximately 25 mph (40 km/h).

n Accelerating

The vehicle can be accelerated normally.

167

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 168 Wednesday, July 30, 2008 3:00 PM

2-4. Using other driving systems

n Automatic cruise control cancellation

The set speed is automatically canceled in any of the following situations. l Actual vehicle speed falls more than 10 mph (16 km/h) below the preset

vehicle speed. At this time, the memorized set speed is not retained.

l Actual vehicle speed is below 25 mph (40 km/h). l VSC is activated.

n If the cruise control indicator flashes

Press the ON-OFF button to turn the cruise control off, and then reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.

CAUTION

n To avoid operating the cruise control by mistake

Keep the ON-OFF button off when not in use.

n Situations unsuitable for cruise control

In heavy traffic

Do not use cruise control in any of the following situations. Doing so may result in control of the vehicle being lost and could cause an accident resulting in death or serious injury. l On roads with sharp bends l On winding roads l On slippery roads, such as those covered with rain, ice or snow l On steep hills l When towing a trailer

168

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 169 Wednesday, July 30, 2008 3:00 PM

2-4. Using other driving systems Electronically modulated air suspension (if equipped)

The electronically modulated air suspension allows the driver to control the vehicle’s height in order to adjust for driving conditions. Select the desired height with the height control switch.

Height control switch HEIGHT CONTROL OFF switch

169

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 170 Wednesday, July 30, 2008 3:00 PM

2-4. Using other driving systems

Selecting vehicle height

Higher Lower

Vehicle height can be adjusted only when the engine is running. The height control indicator stops blinking, and comes on continuously to indicate that the mode shift is completed.

n Height modes

l N mode (normal mode): For ordinary driving

Normal height

l HI mode (high mode): For driving on bumpy roads and through

water 1.6 in. (40 mm) higher than the normal height The HI mode is unavailable when the vehicle’s speed exceeds 18 mph (30 km/h). When the vehicle’s speed exceeds 18 mph (30 km/h), the height will be adjusted to the normal height automatically.

170

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 171 Wednesday, July 30, 2008 3:00 PM

2-4. Using other driving systems

l LO mode (low mode): For the ease of egress/ingress and load-

ing luggage 0.8 in. (20 mm) lower than the normal height The LO mode is unavailable when the vehicle’s speed exceeds 8 mph (12 km/h). When the vehicles speed exceeds 8 mph (12 km/h), the height will be adjusted to the normal height automatically.

Disabling the height control

When the HEIGHT CONTROL OFF switch is pressed, the vehi- cle height is fixed at the current height. The height can be adjusted by pressing the HEIGHT CON- TROL OFF switch again. vehicle’s

When speed exceeds 18 mph (30 km/h), the height will be adjusted to the nor- mal height automatically.

the

171

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 172 Wednesday, July 30, 2008 3:00 PM

2-4. Using other driving systems

n Automatic leveling function

Regardless of the number of occupants or the luggage load, vehicle height in any mode is always adjusted to a fixed height by the automatic leveling function.

n When HI mode is selected

The vehicle height will change to N mode when driving at the speeds of 18
mph (30 km/h).

n When LO mode is selected

l The vehicle height will change to N mode when vehicle speed exceeds 7

mph (12 km/h).

l This mode allows for easy access to the vehicle (getting in and out) and

easy loading and unloading.

n The electronically modulated air suspension will not operate in the fol-

lowing cases: l The underbody of the vehicle is touching the surface of the road. l The area around the suspension is covered with ice. The height control indicators will blink, turn off and then turn on continuously to indicate that the electronically modulated air suspension is not opera- tional. To re-enable operation, turn off the engine and then restart it.

n Even if you hear an operating noise

This does not indicate a problem in the electronically modulated air suspen- sion.

n If there is a problem somewhere in the electronically modulated air

suspension The height control OFF indicator will behave as follows: l The indicator will not come on when the engine switch is turned on. l The indicator will blink. Although the vehicle may be driven, have the vehicle inspected by your Toy- ota dealer.

172

4RUNNER_U_(L/O_0808)

2

4RUNNER_U.book Page 173 Wednesday, July 30, 2008 3:00 PM

2-4. Using other driving systems

CAUTION

n The electronically modulated air suspension must be turned off in the

following circumstances: Otherwise, the automatic leveling function may cause the vehicle’s height to change, resulting in an unexpected accident. l When driving through water such as shallow streams (Put the vehicle height in HI mode and turn off the electronically modulated air suspension. Drive at 18 mph [30 km/h] or slower.)

l When jacking up the vehicle, installing tire chains or tying the vehicle with chains/wires for transportation via flat bed truck (Turn the system off and stop the engine.)

l When the vehicle must be towed (Put the vehicle height in N mode and

turn the system off.)

l When the vehicle gets stuck (Turn the system off.) l When disconnecting a trailer (Put the vehicle height in LO mode and turn

the system off.)

n Selecting the correct height mode

Observe the following precautions to prevent accidents. Failure to do so may cause damage to parts of the vehicle, as well as dan- gerous handling characteristics, which may lead to fatal or injury accidents. l Before you lower the vehicle’s height, check under the vehicle to make

sure that no one is there.

l The HI mode should be used for off-road driving conditions.

As the vehicle’s center of gravity is higher in this setting, the vehicle may become unstable when turning abruptly.

l Do not select HI mode when you load cargo on the roof luggage carrier.

This may result in a loss of control or vehicle rollover.

173

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 174 Wednesday, July 30, 2008 3:00 PM

2-4. Using other driving systems

NOTICE

n Be careful in any place where overhead space is limited.

When changing to a higher mode or after unloading, the vehicle height will rise. This may cause damage to the vehicle.

n Do not select LO mode when driving on bumpy roads.

If the underbody of the vehicle touches a rugged road surface, the vehicle may be damaged.

n Do not change the vehicle height frequently.

The compressor might overheat and cause the operation to stop.

n When on the extremely uneven roads with rocks

Sometimes the vehicle height is not adjusted because it is judged as uneven road driving.

174

4RUNNER_U_(L/O_0808)

2

4RUNNER_U.book Page 175 Wednesday, July 30, 2008 3:00 PM

2-4. Using other driving systems AUTO LSD system (2WD models and Multi-mode 4WD models)

The AUTO LSD system aids traction by using the traction control system to control engine performance and braking when one of the rear wheels begins to spin. The system should be used only when one of the rear wheels spin- ning occurs in a ditch or rough surface. n System operation

The system can be used on 2WD models and in 2WD mode on 4WD models. The system is activated when driving at a speed under 62 mph (100 km/h).

Press the VSC OFF switch to turn on the system.

At this time, the AUTO LSD and slip indicators will come on. To turn off the system, push the switch again. If the engine is turned off while the AUTO LSD and slip indica- tors are on and then restarted, the indicator will turn off auto- matically.

175

4RUNNER_U_(L/O_0808)

4RUNNER_U.book Page 176 Wednesday, July 30, 2008 3:00 PM

2-4. Using other driving systems

When the AUTO LSD system is operating

If the rear wheels spin, the slip indicator flashes to indicate that the AUTO LSD system have been controlled the spinning of the rear wheels.

n If the brake system overheats

The system will cease operation and a buzzer will sound to alert the driver. Stop the vehicle in a safe place. (There is no problem with continuing normal driving.)

CAUTION

n To avoid an accident

l Do not use the AUTO LSD system in conditions other than the above.

A much greater steering effort and more careful cornering control will be required.

l Do not drive with the AUTO LSD system continuously turned on.

176

4RUNNER_U_(L/O_0808)

2