(cid:2) The battery has been disconnected. If your vehicle is out of the set zone, refer to “CALIBRATING THE COMPASS” below to set the zone number. If the compass works to calibrate the direction automati- cally while the vehicle is in motion. For additional precision or calibrating, see COMPASS” below.
for complete THE
“CALIBRATING
is small,
Compass sensor
The compass sensor is in the inside rear view mirror.
NOTICE
Do not put magnets or a metal object on or near the inside rear view mirror of the vehicle. Doing this may cause malfunction of the compass sensor.
298
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
CY19140
the
from
CALIBRATING THE COMPASS (deviation calibration) the compass The direction display on true direction deter- deviates mined by the earth’s magnetic field. The angle of deviation varies according to the geographic position of the vehicle. To adjust this deviation, stop the vehicle, ” switch until then push and hold the “ the zone number appears on the display. Then push the “ ” switch, referring to the following map to select the number of the zone where the vehicle is.
2007 4Runner from Aug. ’06 Prod. (OM35866U)
299
06 06.07
Samoa: 5
Guam:
Saipan: 8
After calibration, leaving the system for several seconds returns it to the compass mode.
CAUTION
Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.
Z19004y
Zone numbers
300
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
Perform circling calibration just after you have purchased your Toyota. And then always perform circling calibration after the battery has been removed, re- placed or disconnected. (cid:2) Do not perform circling calibration of the compass the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).
in a place where
(cid:2) During calibration, do not operate elec- tric systems (moon roof, power win- dows, etc.) as they may interfere with the calibration.
CY19141
CY19033
the direction display on
CALIBRATING THE COMPASS (circling calibration) Sometimes the compass may not change after a turn. To rectify this, stop the vehicle and push and ” switch until “C” appears on hold the “ the display. If “C” appears on the display because of a drastic change in the magnetic field, perform circling calibration.
in a circle, drive around
Drive the vehicle in a circle at 8 km/h (5
mph) or less. If there is not enough space
to drive
the
block.
After driving 1 to 3 circles in the above
method, calibration is completed when the
direction is shown on the display.
If calibration cannot be performed because
of the magnetized vehicle etc., take your
vehicle to Toyota dealer.
2007 4Runner from Aug. ’06 Prod. (OM35866U)
301
06 06.07
CAUTION
(cid:2) When doing the circling calibration, be sure to secure a wide space, and watch out for people and ve- hicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.
(cid:2) Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.
Rear view monitor system The rear view monitor system assists the driver by displaying an image of the view behind the vehicle while back- ing up. The image is displayed in re- verse on the screen. This allows the image to appear in the same manner as that of the rear view mirror. To display the rear view image on the screen, place the selector lever in the “R” position when the ignition switch is in the “ON” position. If you move the selector lever out of the “R” position, the previous screen. Operating another func- tion of the navigation system will display another screen. The rear view monitor system is a supple- ment device intended to assist back up. When backing up, be sure to check be- hind and all around the vehicle visually.
the screen returns
to
CAUTION
the
(cid:2) Never depend on
rear view monitor system entirely when back- ing up. Always make sure your in- tended path is clear. Use caution, when backing up any vehicle.
just as you would
image on
(cid:2) Never back up while looking only at the screen. The the screen is different from actual con- ditions. Depicted distances between objects and flat surfaces will differ from actual distance. If you back up while looking only at the screen, you may hit a vehicle, a person or an object. When backing up, be sure to check behind and all around the vehicle visually and with mir- rors before proceeding.
302
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
(cid:2) Do not use the system when the back door is not completely closed. (cid:2) If the back of the vehicle is hit, the position and mounting angle of the camera may change. Be sure to have the camera’s position and mounting angle checked at your Toyota dealer.
(cid:2) If the temperature changes rapidly, such as when hot water is poured on the vehicle in cold weather, the system may not operate normally.
(cid:2) If the camera lens becomes dirty, it cannot transmit a clear If water droplets, snow, or mud ad- here to the lens, rinse with water and wipe with a soft cloth. If the lens is extremely dirty, wash it with a mild cleanser and rinse.
image.
(cid:2) Use your own eyes to confirm the vehicle’s surroundings, as the dis- played image may become faint or dark, and moving images will be distorted, or not entirely visible when is low. When backing up, be sure to check behind and all around the ve- hicle visually and with mirror before proceeding.
the outside
temperature
When replacing the tires, please consult your Toyota dealer. If you replace the tires, the area displayed on the screen may change.
NCY002
On screen
Corners of bumper
2007 4Runner from Aug. ’06 Prod. (OM35866U)
303
06 06.07
AREA DISPLAYED ON SCREEN Image is displayed approximately level on screen. (cid:2) The area detected by the camera is limited. The camera does not detect objects which are close to either corner of the bumper or under the bumper.
(cid:2) The area displayed on the screen may vary according to vehicle orien- tation or road conditions.
CY19136
(cid:2) When water droplets are adhering to the camera, or when humidity is high (for example, when it rains)
(cid:2) When
foreign matter
(for example, snow or mud) is adhering to the cam- era
(cid:2) When the sun or the beam of head- lights is shining directly into the cam- era lens
THE REAR VIEW MONITOR SYSTEM CAMERA The rear view monitor system camera is located on the back door as shown in the illustration. The camera uses a special lens. The distance of the image that ap- pears on the screen differs from the actu- al distance. In it may become difficult to see the images on the screen, even when the system is functioning. (cid:2) In the dark (for example, at night) (cid:2) When the temperature near the lens is
following cases,
the
high or low
304
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
Power outlet (12 VDC)
CY19118
CY19002
If a bright light (for example, sunlight re- flected off the vehicle body) is picked up by the camera, the smear effect* peculiar to the camera may occur. * : Smear effect—A phenomenon that oc- curs when a bright light (for example, sun- light reflected off is picked up by trans- mitted by light source appears to have a vertical streak above and below it.
the camera; when
the vehicle body)
the camera,
the
CY19035
Luggage compartment
for
The power outlets are designed power supply for car accessories. In the rear console box—To use the power outlet, push the lid of the auxil- iary box to open. The key must be in the “ACC” or “ON” position for the power outlet to be used.
Rear console box
2007 4Runner from Aug. ’06 Prod. (OM35866U)
305
06 06.07
NOTICE
(cid:1) To prevent the fuse from being
blown, do not use the electricity
over the total vehicle capacity of 12
VDC/120W.
(cid:1) To prevent the battery from being discharged, do not use the power outlets longer than necessary when the engine is not running.
(cid:1) Close the power outlet lids when the power outlets are not in use. Inserting anything other than an ap- propriate plug that fits the outlet, or allowing any liquid to get into the outlet may cause electrical fail- ure or short circuits.
Power outlet (115 VAC)
CY19137
CY19135
This power outlet is designed for use as a power supply for electric ap- pliances in the vehicle. The key must be in the “ON” position for the power outlet to be used. The maximum capacity for this power out- let is 115 VAC/100W. If you attempt to use an appliance that requires more than 115 VAC or 100W, the protection circuit will activate and cut the power supply. The power supply will restart automatically when you use an appliance that operates within the 115 VAC/100W limits.
To use the power outlet, push the main switch on the instrument panel. An indicator light will illuminate to indicate that the power outlet is ready for use. Push the main switch once again to turn the power outlet off. When the power out- let is not in use, make sure that the main switch is turned off.
306
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
NOTICE
(cid:1) To prevent the battery from being discharged, do not use the power outlet longer than necessary when the engine is not running.
(cid:1) Close the power outlet lid when the power outlet is not in use. Inserting anything other than an appropriate plug that fits the outlet may cause electrical failure or short circuits.
The power outlet is not designed for the following electric appliances even though their power consumption is un- der 115 VAC/100W. These appliances may not operate properly.
(cid:2) Appliances with high initial peak watt- age: cathode−ray tube type televisions, compressor−driven refrigerators, electric pumps, electric tools, etc.
(cid:2) Measuring devices which process pre- cise data: medical equipment, measur- ing instruments, etc.
(cid:2) Other appliances requiring an extremely stable power supply: microcomputer− controlled electric blankets, touch sen- sor lamps, etc.
Certain electrical appliances may cause radio noise.
Glove box
CY19127
To use the glove box: Open by pulling the lever. Lock by inserting the master key and turn- ing it clockwise. Unlock by inserting the master key and turning it counterclockwise. With the instrument panel lights on, the glove box light will come on.
CAUTION
To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.
injury
2007 4Runner from Aug. ’06 Prod. (OM35866U)
307
06 06.07
CY19070
On some models, an auxiliary box is located inside the glove box. To increase the capacity of the glove box, raise the lower panel of the auxiliary box.
Garage door opener
Indicator light
CY19130
Buttons
(cid:3)
The garage door opener ( Universal Transceiver) is manufactured under license from HomeLink(cid:3) and can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, and security systems, etc.
308
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
transmitter prior
(a) Programming the HomeLink(cid:3)
The HomeLink(cid:3) in your vehicle has 3
buttons and you can store one program
for each button.
To ensure correct programming into the
HomeLink(cid:3), install a new battery in the
hand−held
to program-
ming.
The battery side of the hand−held trans-
mitter must be pointed away
the
HomeLink(cid:3) during the programming pro-
cess.
For Canadian users, follow the procedure
“Programming an entrance gate/pro-
in
gramming all devices
the Canadian
market”.
1. Decide which of 3 HomeLink(cid:3) buttons
from
in
you want to program.
HomeLink(cid:5)
CY19131
25 to 75 mm (1 to 3 in.)
CY19132
Hand−held garage transmitter
2. Place your hand−held garage transmit- ter 25 to 75 mm (1 to 3 in.) away from the surface of the HomeLink(cid:3).
Keep the indicator light on the HomeLink(cid:3) in view while programming.
3. Simultaneously press and hold
the hand−held garage transmitter button along with the selected HomeLink(cid:3) but- ton.
Do not release the buttons until step 4
has been completed.
4. When
the HomeLink(cid:3) changes from a slow to a rapid flash after 20 seconds, you can release both buttons.
light on
indicator
the
2007 4Runner from Aug. ’06 Prod. (OM35866U)
309
06 06.07
CY19034
5. Test the operation of the HomeLink(cid:3) by
pressing the newly programmed button.
If programming a garage door opener,
check to see if the garage door opens
and closes.
If
the garage door does not operate,
identify if your garage transmitter is of the
“Rolling Code” type. Press and hold the
programmed HomeLink(cid:3)
The
garage door has the rolling code feature if
the HomeLink(cid:3))
the
flashes rapidly and then remains lit after 2
seconds. If your garage transmitter is the
“Rolling Code”
the
heading
rolling code
system”.
“Programming a
type, proceed
indicator
button.
light
(on
to
310
6. Repeat steps 2 through 5 for each re- maining HomeLink(cid:3) button to program another device.
it
is
to
is necessary
Programming a rolling code system “Rolling Code” If your device equipped, follow steps 1 through 4 under the heading “Programming the HomeLink(cid:3)” before proceeding with the steps listed below. 1. Locate the “training” button on the ceil- ing mounted garage door opener motor. The exact the button may vary by brand of garage door opener. Refer the owner’s guide supplied by the garage door opener manufacturer for the location of this “training” button.
location and color of
to
2. Press the “training” button on the ceil- ing mounted garage door opener motor. Following this step, you have 30 seconds in which to initiate step 3 below. 3. Press and release the vehicle’s pro- grammed HomeLink(cid:3) button twice. The garage door may open. the door does open, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door.
If
now
should
recognize
The ceiling mounted garage door opener motor the HomeLink(cid:3) unit and be able activate the garage door up/down. 4. Repeat steps 1 through 3 for each re- maining HomeLink(cid:3) button to program another rolling code system.
Programming an entrance gate/program- ming all devices in the Canadian market 1. Decide which of the 3 HomeLink(cid:3) but-
2. Place
your
tons you want to program. hand−held
gate/device transmitter 25 to 75 mm (1 to 3 in.) away the HomeLink(cid:3).
surface
from
the
of
Keep the indicator light on the HomeLink(cid:3) in view while programming. 3. Press
selected
hold
and
the
HomeLink(cid:3) button.
4. Continuously press and release (cycle)
transmitter
the hand−held gate/device
button every two seconds until step 5
is complete.
the
the HomeLink(cid:3) changes from a slow to a rapid flash after 20 seconds, you can release both buttons.
light on
5. When
indicator
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
6. Test the operation of the HomeLink(cid:3) by pressing the newly programmed button. Check to see if the gate/device oper- ates correctly.
7. Repeat steps 1 through 6 for each re- maining HomeLink(cid:3) button to program another device.
Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. Reprogramming a button Individual HomeLink(cid:3) buttons cannot be erased, however, to reprogram a single button, follow the procedure “Programming the HomeLink(cid:3)”. (b) Operating the HomeLink(cid:3) To operate the appropriate HomeLink(cid:3) button to activate the programmed device. The HomeLink(cid:3) indicator light should come on. The HomeLink(cid:3) continues to send the signal for up the button is pressed.
the HomeLink(cid:3), press
to 20 seconds as
long as
your
For additional programming assistance with Universal Transceiver call the: (cid:2) The
Toyota Customer Experience
HomeLink(cid:3)
CY19133
Center at 1−800−331−4331 (U.S.A.)
(cid:2) Toyota Canada Customer
Interaction
Centre at 1−888−869−6828 (Canada) Refer to HomeLink(cid:3) on the internet at: WWW.HOMELINK.COM
(c) Erasing
the
entire HomeLink(cid:3)
memory (all three programs)
To erase all previously programmed codes
at one time, press and hold down the 2
outside buttons for 20 seconds until the
indicator light flashes.
If you sell your vehicle, be sure to erase
the HomeLink(cid:3)
the programs stored
memory.
in
2007 4Runner from Aug. ’06 Prod. (OM35866U)
311
06 06.07
CAUTION
(cid:2) When programming the HomeLink(cid:3) Universal Transceiver, you may be operating a garage door or other device. Make sure people and ob- jects are out of the way of the ga- rage door or other device to pre- vent potential harm or damage.
(cid:2) Do not use this HomeLink(cid:3) Univer- sal Transceiver with any garage door opener that lacks the safety stop and reverse feature as re- quired by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982.) A garage door open- er which cannot detect an object (signaling the door to stop and re- verse), does not meet current feder- al safety standards. Using a garage door opener without these features increases risk of serious injury or death.
received,
This device complies with Part 15 of the FCC Rules and with RSS−210 of the IC Rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer- ence interference that may cause undesired operation. WARNING: This transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party re- sponsible for compliance could void the user’s authority to operate the device.
including
Auxiliary boxes— To use the auxiliary boxes, open the lids as shown in the following illustra- tions.
CAUTION
(cid:2) To reduce the chance of injury in case of an accident or a sudden stop, always keep the auxiliary box closed while driving.
(cid:2) Type A—As this holder is designed for holding a light object such as eyeglasses, do not place any heavy objects in them. Heavy objects may cause the holder to open and the contents to fly out resulting in inju- ries.
NOTICE
Type A—During hot weather, the inte- rior of the vehicle becomes very hot. Do not leave anything flammable or deformable such as a lighter, glasses, etc. inside.
312
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
CY19005
CY19036
CY19069
Type A (overhead console)
Type C (rear console box)
Type E (right side of luggage compart- ment)
CY19007
CY19112
Type B (instrument panel)
Type D (rear tire house)
2007 4Runner from Aug. ’06 Prod. (OM35866U)
313
06 06.07
—Using the holding belts
Rear console box
CY19074
The right side of luggage compartment auxiliary box is equipped with a belt to hold the objects. To use the belt, do the following. 1. To loosen: Pull the buckle forward. 2. To tighten: Pull on the belt. Make sure the objects are securely held.
CY19071
CONSOLE BOX TABLE To use the console box table, open it.
CAUTION
To reduce the chance of in case of an accident or a sudden stop, always keep the table closed while driving.
injury
NOTICE
To prevent damage to the table, do
not place any object heavier than 1
kg (2.20 lb.) on it, and do not leave
any object on the table for a long
time.
314
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
CY19104
CONSOLE BOX To access the rear console box, pull up the console box lid while pushing the lock release button.
CAUTION
To reduce the chance of in case of an accident or a sudden stop, always keep the console box closed while driving.
injury
Tissue box holder
CY19105
The rear console box is equipped with a tissue box holder on the inside of the rear console box lid. To use the tissue box holder: 1. Pull up the console box lid while push-
ing the lock release button.
2. Place a tissue box in the lid.
CAUTION
To reduce the chance of in case of an accident or a sudden stop while driving, keep the console box lid closed when it is not in use.
injury
2007 4Runner from Aug. ’06 Prod. (OM35866U)
315
06 06.07
Coin holder
Trash holder
The rear console box is equipped with a coin holder. To use the coin holder: 1. Pull up the console box lid while push-
ing the lock release button.
2. Push coins down into the holder. The coin holder is detachable.
CY19106
CY19038
316
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
The trash holder is designed to use the grocery bag as a trash bag. To use the trash holder: 1. Raise the trash holder. 2. Fit the grocery bag onto the holder by hanging its handles on the two hooks indicated at the left and right. trash holder can support
to 1 kg
The (2.20 lb.).
CAUTION
To reduce the chance of in case of an accident or a sudden stop while driving, keep the trash holder closed when it is not in use.
injury
Front cup holders
CY19111
CY19064
If the trash holder is pulled strongly or stepped on, it will detach from the rear console box to protect it from damag- ing. If the trash holder becomes detached, re- install it in a horizontal direction as indi- cated It cannot be installed in any other direction.
illustration.
the
in
NOTICE
Do not deliberately pull or step on the trash holder, as it may be dam- aged or broken.
2007 4Runner from Aug. ’06 Prod. (OM35866U)
317
06 06.07
The cup holders are designed for hold- ing cups or drink−cans securely. The cup holder can be adjustable to the size of the cups or drink−cans by changing the holder position and the arm position, as shown. With the instrument panel lights on, the front cup holder position indicator lights will come on.
CAUTION
Do not place anything else other than cups or drink−cans in the cup holder, as such items may be thrown about in the compartment and possibly in- jured people the vehicle during sudden braking or in an accident.
in
Rear cup holders and tray (vehicles without third seats)
CY19075
tray are
The rear cup holders and housed in the armrest. The cup holders are designed to hold cups or beverage cans securely. 1. To use the rear cup holders and tray,
pull the armrest out.
CY19100
318
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
2. To use the rear cup holder, push and
pull it out.
CY19101
3. To use the tray, pull it out.
CAUTION
(cid:2) Do not place anything else other than cups or drink−cans in the cup items may be holder, as such thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.
(cid:2) To reduce the chance of injury in case of an accident or sudden stop while driving, keep the cup holder closed when it is not in use.
(cid:2) To reduce the chance of injury in case of an accident or a sudden stop, always keep the tray closed while driving.
NOTICE
To prevent damage to the tray, do not place any object heavier than 2 kg (4.40 lb.) on it, and do not leave any object on the tray for a long time.
2007 4Runner from Aug. ’06 Prod. (OM35866U)
319
06 06.07
Rear cup holders (vehicles with third seats)
Bottle holders
CY19114
Type A (armrest)
CY19113
Type B (rear tire house)
320
The cup holders are designed for hold- ing cups or drink−cans securely. Type A—To use the holder, pull the arm- rest out and push the lid.
CAUTION
(cid:2) Do not place anything else other than cups or drink−cans in the cup items may be holder, as such thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.
(cid:2) Type A—To reduce the chance of injury in case of an accident or sudden stop while driving, keep the cup holder closed when it is not in use.
CY19015
Front doors
CY19016
Rear doors
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
The bottle holders are designed to hold bottles securely.
CAUTION
Do not attempt to use the holder for any other purpose for which it was intended. Inappropriately sized or shaped objects may be thrown about in the compartment and possibly in- jure people in the vehicle during a sudden braking or an accident.
Tie−down hooks
Grocery bag hooks
CY19044
CY19076
NOTICE
Do not put a cup or open bottle in the bottle holder because the con- tents may spill when the door opens or closes.
To secure your luggage, use the tie−
down hooks as shown above.
See “—Stowage precautions” on page 351
in Section 2 for precautions when loading
luggage.
CAUTION
To avoid personal injury, keep the tie− down hooks folded in place on the floor when not in use.
NOTICE
Do not use the seat anchors instead of the tie−down hooks.
These hooks are designed things like grocery bags.
to hang
NOTICE
To prevent damage to the hook, do not hang any object heavier than 1 kg (2.20 lb.) in it.
2007 4Runner from Aug. ’06 Prod. (OM35866U)
321
06 06.07
Cargo net hooks
Luggage cover
USING LUGGAGE COVER To use the luggage cover: 1. Attach the front hooks of the lug-
gage cover to the head restraint.
2. Pull out the rear luggage cover and
hook it on the anchors.
CAUTION
Do not place anything on the luggage cover. Such thrown about and possibly injure people in the vehicle during sudden braking or a collision.
items may be
CY19103
CY19045
These hooks are designed to hang the cargo net. To hang the cargo net, use the cargo net hooks and rear tie−down hooks. Although the cargo net itself is not in- cluded as an original equipment, these hooks can be used to hang the cargo net.
NOTICE
To prevent damage to the hook, avoid hanging things other than a cargo net on it.
322
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
Double deck
CY19067
CY19058
CY19068
To use the double deck: 1. Turn the left and right knobs from the
position
to
“LOCK”
the “UNLOCK” position.
2. Hold the handle and raise the double
deck on the rear tire houses.
REMOVING LUGGAGE COVER To remove the luggage cover, detach its hooks from the head restraint. Then, retract and release both ends, and re- move the luggage cover. After you remove the luggage cover, place it somewhere other the passenger compartment. This will prevent passengers from injury in the event of a sudden stop or accident.
than
2007 4Runner from Aug. ’06 Prod. (OM35866U)
323
06 06.07
Roof luggage carrier
NOTICE
When using the double deck at the raised position, do not place any ob- ject heavier than 30 kg (66 lb.).
CY19052
3. Turn the left and right knobs from the
“UNLOCK” position
to
the “LOCK” position.
CY19129
Make sure the double deck is securely locked.
CAUTION
injury
To reduce the chance of in case of an accident or sudden stop, make sure the double deck knobs are always in the “LOCK” posi- tion when the double deck is in the raised or lowered position.
that
324
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
The roof luggage carrier consists of roof rails (1) attached to the roof and sliding cross rails (2). To adjust the positions of cross rails, do this. 1. Turn
the knobs counterclockwise
to
loosen the cross rails. the cross rails
2. Slide
position various sizes.
for
loading
to the
the desired luggages of
installing
3. After adjusting, be sure to tighten the cross rails by turning knobs clockwise. Follow the manufacturer’s instructions and precautions when the attach- ments or their equivalent. there is no luggage on the roof When luggage carrier, Toyota recommends that the front and rear cross rails be secured in the positions indicated in the illustra- tion, according to the following procedure. This may diminish wind noise during driv- ing.
CAUTION
When you load cargo on the roof lug- gage carrier, observe the following: (cid:2) Place the cargo so that its weight is distributed evenly between the front and rear axles.
(cid:2) If driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then dur- ing the trip to make sure the cargo remains in its place.
(cid:2) Do not exceed 54 kg (120 lb.) cargo weight on the roof luggage carrier.
(cid:2) If loading long or wide cargo, never
exceed the vehicle overall length or
width.
and
weights” on page 446 in Section 8
for
information on your vehicle
overall length and width.)
“Dimensions
(See
NOTICE
When loading the luggages, be careful not to scratch the surface of the moon roof.
(cid:2) Before driving, make sure the cargo the roof
fastened on
is securely luggage carrier.
(cid:2) Loading cargo on the roof luggage carrier will make the center of the vehicle gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneu- vers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle cor- rectly.
2007 4Runner from Aug. ’06 Prod. (OM35866U)
325
06 06.07
Floor mat
CY19047
CY19048
Use a floor mat of the correct size. If the vehicle carpet and floor mat have 2 holes, then they are designed for use with locking clips. Attach the floor mat to the vehicle carpet using the clips. Look the clips the vehicle carpet.
the holes
into
in
CAUTION
Make sure the floor mat is properly placed on the vehicle carpet. If the floor mat slips and interferes with the movement of the pedals during driv- ing, it may cause an accident.
326
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.07
Foreword
Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and quality construction of each vehicle we build. This Owner’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. For important information about this manual and your Toyota, read the following pages carefully. When it comes to service, remember that your Toyota dealer knows your vehicle very well and is interested in your complete satisfaction. Your Toyota dealer will provide quality maintenance and any other assistance you may require. If there is not a Toyota dealer near you, please call the following number: U.S. OWNERS:
(cid:1) When traveling in the U.S. mainland or Canada:
Toyota Customer Experience Center
Toll−free:1−800−331−4331
(cid:1) Hawaii:
Servco Automotive Customer Services
Toll−free:1−888−272−5515
CANADIAN OWNERS:
(cid:1) When traveling in Canada or the U.S. mainland:
Toyota Canada Customer Interaction Centre
Toll−free:1−888−TOYOTA−8 or 1−888−869−6828
Please leave this Owner’s Manual in this vehicle at the time of resale. The next owner will need this information also.
All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy of
continual product improvement, we reserve the right to make changes at any time without notice.
Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may
find some explanations for equipment not installed on your vehicle.
Please access our websites for further information.
(cid:1) The U.S. mainland
(cid:1) Hawaii
(cid:1) Canada
www.toyota.com www.toyotahawaii.com www.toyota.ca
2006 TOYOTA MOTOR CORPORATION All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of Toyota Motor Corporation.
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
Quick index (cid:1) If a service reminder indicator or warning buzzer comes on (cid:1) If your vehicle will not start (cid:1) If your engine stalls while driving (cid:1) If your vehicle overheats (cid:1) If you have a flat tire (cid:1) If your vehicle needs to be towed (cid:1) Tips for driving during break−in period (cid:1) How to start the engine (cid:1) General maintenance (cid:1) Complete index Gas station information Fuel type:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
147
374
377
378
379
389
329
356
407
NO TAG
UNLEADED gasoline, Octane Rating 87 (Research Octane Number 91) or higher. See page 329 for detailed information.
Fuel tank capacity:
87 L (23.0 gal., 19.1 Imp. gal.)
Engine oil:
ILSAC multigrade engine oil is recommended. See page 421 for detailed information.
Tire information: See pages 425 through 432. Tire inflation pressure: See page 451.
2007 4Runner from Aug. ’06Prod. (OM35866U)
U -2
Publication No. OM35866U
Part No. 01999-35866
Printed in Japan 01−0607−00
( U)
06 06.07
Important information about this manual
Safety and vehicle damage warnings
Safety symbol
Throughout this manual, you will see safety and vehicle dam- age warnings. You must follow these warnings carefully to avoid possible injury or damage. The types of warnings, what they look like, and how they are used in this manual are explained as follows:
CAUTION
This is a warning against anything which may cause injury to people if the warning is ignored. You are informed about what you must or must not do in injury to yourself and order to reduce the risk of others.
NOTICE
This is a warning against anything which may cause damage to the vehicle or its equipment if the warning is ignored. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your vehicle and its equipment.
the safety symbol When you see shown above, it means: “Do not...”; “Do not do this”; or “Do not let this happen”.
ii
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
Important information about your Toyota
Occupant restraint systems
Toyota encourages you and your family to take the time to read Section 1−3 of this Owner’s Manual carefully. In terms of helping you understand how you can receive the maximum benefit of the occupant restraint systems this vehicle provides, Section 1−3 of this Owner’s Manual is the most important Section for you and your family to read. Section 1−3 describes the function and operation concern- ing seats, seat belts, SRS airbags and child restraint sys- tems of this vehicle and some potential hazards you should be aware of. These systems work together along with the overall structure of this vehicle in order to provide occupant restraint in the event of a crash. The effect of each system is enhanced when it is used properly and together with other systems. No single occupant restraint system can, by itself, provide you or your family with the equal level of restraint which these systems can provide when used together. That is why it is important for you and your family to understand the purpose and proper use of each of these systems and how they relate to each other.
The purpose of all occupant restraint systems is to help reduce the possibility of death or serious injury in the event of a collision. None of these systems, either individ- ually or together, can ensure that there is no injury in the event of collision. However, the more you know about these systems and how to use them properly, the greater your chances become of surviving an accident without death or serious injury.
Seat belts provide the primary restraint to all occupants of the vehicle, and every occupant of the vehicle should wear seat belts properly at all times. Children should always be secured in child restraint systems that are appropriate for their age and size. SRS (Supplemental Restraint System) airbags are, as their names imply, designed to work with, and be supplemental to, seat belts and are not substitutes for them. SRS airbags can be very effective in reducing the risk of head and chest injuries by preventing contact of the head and chest with interior portions of the vehicle.
iii
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
In order to be effective, the SRS airbags must deploy with tremendous speed. The rapid deployment of the SRS air- bags makes the SRS airbags themselves potential sources of death or serious injury if an occupant is too close to an airbag, or if an object or some part of his or her body has been placed between the occupant and the airbag at the time of deployment. This is just one example of how the instructions in Section 1−3 of this Owner’s Manual will help ensure proper use of the occupant restraint systems, and increase the safety they can provide to you and your fami- ly in the event of an accident.
Toyota recommends you to read the provisions in Section 1−3 carefully and refer to them as needed during your time of ownership of this vehicle.
Event data recorder
Your vehicle has computers that monitor and control cer- tain aspects of your vehicle. These computers assist in driving and maintaining optimal vehicle performance. Be- sides storing data useful for troubleshooting, there is a system to record data in a crash or a near car crash event. This is called an Event Data Recorder (EDR).
The SRS airbag sensor assembly contains the EDR. In a crash or a near car crash event, this device may record some or all of the following information:
(cid:1) Engine speed (cid:1) Whether the brake pedal was applied or not (cid:1) Vehicle speed (cid:1) To what extent the accelerator pedal was depressed (cid:1) Position of the transmission selector lever (cid:1) Whether the driver and front passenger wore the
seat belts or not
(cid:1) Driver’s seat position (cid:1) Front passenger’s occupant classification
iv
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
(cid:1) SRS airbag deployment data (cid:1) SRS airbag system diagnostic data
If your vehicle is equipped with a vehicle stability control (VSC) system, its Electronic Control Unit (ECU) may con- tain another EDR. There are a variety of driving situations which include activating the VSC under which the VSC EDR will record certain information. The VSC EDR may record some or all of the following information:
(cid:1) Behavior of the vehicle (cid:1) Steering wheel angle (cid:1) Vehicle speed (cid:1) To what extent the accelerator pedal was depressed (cid:1) To what extent the brake pedal was applied (cid:1) To what extent the ECU controlled the condition of
the 4 wheels
(cid:1) Vehicle stability control system diagnostic data
The information above is intended to be used for the purpose of improving vehicle safety performance. Unlike general data recorders, the EDR does not record sound data such as conversation between passengers.
Toyota will not disclose the data recorded in an EDR to a third party except when:
(cid:1) An agreement from the vehicle’s owner (or the leas-
ing company for a leased vehicle) is obtained
(cid:1) Officially requested by the police or other authorities (cid:1) Used as a defense for Toyota in a law suit (cid:1) Ordered by the court
However, if necessary Toyota will:
(cid:1) Use the data for research on Toyota vehicle safety
performance
(cid:1) Disclose the data to a third party for research pur- the vehicle
poses without disclosing details of
owner, and only when it is deemed necessary
(cid:1) Disclose summarized data cleared of vehicle identifi- cation information to a non−Toyota organization for
research purposes
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
New vehicle warranty
Your new vehicle is covered by the following Toyota limited warranties:
(cid:1) New vehicle warranty (cid:1) Emission control systems warranty (cid:1) Others further
information, please refer
Information Booklet” or
For Warranty Supplement”.
to the “Owner’s “Owner’s Manual
Your responsibility for
maintenance
It is the owner’s responsibility to make sure that the speci- fied maintenance is performed. Section 6 gives details of these maintenance requirements. Also included in Section 6 is general maintenance. For scheduled maintenance in- formation, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.
Important health and safety
information about your Toyota
CAUTION
(cid:1) WARNING: Engine exhaust, some of its constitu- ents, and a wide variety of automobile compo- nents contain or emit chemicals known to the State of California to cause cancer and birth de- fects and other reproductive harm. In addition, oils, fuels and fluids contained in vehicles as well as waste produced by component wear con- tain or emit chemicals known to the State of California to cause cancer and birth defects or
other reproductive harm.
(cid:1) Battery posts, terminals and related accessories contain lead and lead compounds. Wash your hands after handling. Used engine oil contains chemicals that have caused cancer in laboratory animals. Always protect your skin by washing
thoroughly with soap and water.
vi
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
Accessories, spare parts and modification of your Toyota
Spark ignition system of your
Toyota
The spark ignition system in your Toyota meets all require- ments of the Canadian Interference−Causing Equipment Standard.
A wide variety of non−genuine spare parts and accessories for Toyota vehicles are currently available in the market. You should know that Toyota does not warrant these prod- ucts and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
This vehicle should not be modified with non−genuine Toyota products. Modification with non−genuine Toyota products could affect its performance, safety or durability, and may even violate governmental regulations. In addi- tion, damage or performance problems resulting from the modification may not be covered under warranty.
vii
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
Installation of a mobile two−way radio system
As the installation of a mobile two−way radio system in your vehicle could affect electronic systems such as fol- lows, be sure to check with your Toyota dealer for precau- tionary measures or special instructions regarding installa- tion.
(cid:1) Multiport
fuel
injection system/sequential multiport
fuel injection system
(cid:1) SRS airbag system (cid:1) Seat belt pretensioner system (cid:1) Traction control system (two−wheel drive models) (cid:1) Active traction control system
(four−wheel drive models)
(cid:1) “AUTO LSD” system (two−wheel drive models) (cid:1) Vehicle stability control system (cid:1) Downhill assist control system
(four−wheel drive models)
(cid:1) Hill−start assist control system (cid:1) Rear height control air suspension
(cid:1) Tire pressure warning system (cid:1) Cruise control system (cid:1) Anti−lock brake system (cid:1) Electronic throttle control system
Tires and loading on your
Toyota
Underinflated or overinflated tire pressure and the excess load may result in the deterioration of steering ability and braking ability, leading to an accident. Check the tire inflation pressure periodi- cally and be sure to keep the load limits given in this Owner’s Manual. For details about tire inflation pressure and load limits, see pages 425 and 350.
viii
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
Scrapping of your Toyota
If
The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals. is scrapped with the airbags and pretensioners left as they are, it may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt preten- sioner removed and disposed of by a qualified service shop or by your Toyota dealer before you dispose of your vehicle.
the vehicle
On−pavement and off−road
driving tips
This vehicle belongs to the utility vehicle class. Utility ve- hicles have a significantly higher rollover rate than other types of vehicles. This vehicle will handle and maneuver differently from an ordinary passenger car because it is designed for off−road use also. In addition, this vehicle has a higher ground clearance and center of gravity than that of an ordinary passenger car. This vehicle design fea- ture causes this type of vehicle to be more likely to rol- lover. Failure to operate this vehicle correctly may result in loss of control, accidents or vehicle rollover causing death or serious injury. Be sure to read “Off−road vehicle precau- tions” on page 328 in Section 2 and “Off−road driving pre- cautions” on page 359 in Section 3.
ix
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
Leak detection pump
This pump performs fuel evaporation leakage check. This check is done approximately five hours after the engine is turned off. So you may hear sound coming from under- neath the luggage compartment for several minutes. It does not indicate a malfunction.
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
You should know as much about the quality and importance of proper maintenance of your new vehicle as the people who built it.
The Toyota authorized Repair Manual tells you how to maintain your vehicle and enables you to correctly perform your own maintenance.
The best way to keep your new vehicle in top running order is to maintain it properly from the moment you drive it off the showroom floor.
The Toyota authorized Repair Manual is packed with literally everything you need to know to perform your own maintenance in virtually every area of your new vehicle.
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
Maintenance procedures for the engine, chassis, body, electrical system, and more, are clearly explained and illustrated.
Periodic maintenance and tune-up
Periodic maintenance and tune-up helps to pre› vent small problems from growing into larger ones lat› er on. The repair manual outlines exactly what main› tenance is required and clearly explains how to do the work yourself step-by-step.
Areas covered include such things as spark plug re› placement, valve clearance adjustment and engine oil and filter replacement.
Where to obtain the
Repair Manual
The repair manual for 4RUNNER may be pur› chased from any Toyota dealer or the Material Distribution Center. To purchase the repair manual, please contact your Toyota dealer or call the Material Distribution Center toll-free at 1-800-622-2033.
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.07
WE REALLY CARE ABOUT YOU (cid:1) PLEASE BUCKLE UP
Toyota has made a special effort to encourage use of seat belts.
Toyota belts are:
(cid:1) Comfortable (cid:1) Easy to use (cid:1) Convenient
We encourage you to use your belts every time you drive.
2007 4Runner from Aug. ’06Prod. (OM35866U)
06 06.08
SECTION 2
INFORMATION BEFORE DRIVING YOUR TOYOTA Information before driving your Toyota Off−road vehicle precautions Break−in period Fuel Fuel pump shut off system Operation in foreign countries Three−way catalytic converters Engine exhaust cautions Facts about engine oil consumption Iridium−tipped spark plugs Brake system Brake pad wear limit indicators Limited−slip differential Your Toyota’s identification Theft prevention labels Suspension and chassis Tire information Vehicle load limits Cargo and luggage Types of tires
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
328
329
329
331
331
332
333
333
334
335
338
339
339
340
341
342
350
351
354
2007 4Runner from Aug. ’06 Prod. (OM35866U)
327
06 06.08
Off−road vehicle precautions
CY20035
This vehicle belongs to the utility ve- hicle class, which has higher ground clearance and narrower tread in relation to the height of its center of gravity to make it capable of performing in a wide variety of off−road applications. Specific design characteristics give it a higher center of gravity than ordinary passen- ger cars. This vehicle design feature causes this type of vehicle to be more likely to rollover. And, utility vehicles have a significantly higher rollover rate than other types of vehicles. An advan- tage of the higher ground clearance is a better view of the road allowing you is not de- to anticipate problems. signed the same speeds as ordinary passenger cars any more than low−slung sports cars de- signed to perform satisfactorily under off−road conditions. Therefore, sharp turns at excessive speeds may cause rollover.
It for cornering at
CAUTION
Always observe the following precau- tions to minimize the risk of serious personal injury or damage to your ve- hicle: (cid:1) In a rollover crash, an unbelted per- son is significantly more likely to die than a person wearing a seat belt. Therefore, the driver and all passengers should fasten their seat belts whenever the vehicle is mov- ing.
(cid:1) Avoid sharp turns or abrupt maneu- vers, if at all possible. Failure to operate this vehicle correctly may result in loss of control or vehicle rollover causing death or serious injury.
(cid:1) Loading cargo on the roof luggage carrier will make the center of the vehicle gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneu- vers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle cor- rectly.
328
2007 4Runner from Aug. ’06 Prod. (OM35866U)
06 06.08
(cid:1) Always slow down in gusty cross- winds. Because of its profile and higher center of gravity, your ve- hicle to side winds than an ordinary passenger car. Slowing down will allow you to have better control.
is more sensitive
jump, make sharp
(cid:1) When driving off−road or in rugged terrain, do not drive at excessive speeds, turns, strike objects, etc. This may cause loss of control or vehicle rollover causing death or serious injury. You are also risking expensive damage to your vehicle’s suspension and chassis.
(cid:1) Do not drive horizontally across steep slopes. Driving straight up or straight down is preferred. Your ve- hicle (or any similar off−road ve- hicle) can tip over sideways much more easily than forward or back- ward.
Break−in period Drive gently and avoid high speeds. Your vehicle does not need an elaborate break−in. But following a few simple tips for the first 1600 km (1000 miles) can add to the future economy and long life of your vehicle: (cid:1) Avoid full
throttle acceleration when
starting and driving.
(cid:1) Avoid racing the engine. (cid:1) Try to avoid hard stops during the first
300 km (200 miles).
(cid:1) Do not drive for a long time at any
single speed, either fast or slow.
(cid:1) Do not tow a trailer during the first 800
km (500 miles).
Fuel
FUEL TYPE
Your new vehicle must use only un-
leaded gasoline.
To help prevent gas station mix−ups, your
Toyota has a smaller fuel tank opening.
The special nozzle on pumps with un-
leaded fuel will fit it, but the larger stan-
dard nozzle on pumps with leaded gas will
not.
At a minimum,
the gasoline you use
should meet the specifications of ASTM
D4814 in the U.S.A. and CGSB 3.5−M93
in Canada.
NOTICE
Do not use leaded gasoline. Use of