2007 Toyota 4runner Owners Manual

battery. Their fumes are flammable. (cid:2) Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.

(cid:2) Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc. (cid:2) Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your thoroughly with soap skin, wash and water.

(cid:2) Do not

leave used oil within the

reach of children.

(cid:2) Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your dealer or a service station information concerning recycling or disposal.

for

(cid:2) Be extremely cautious when work- ing on the battery. It contains poi- sonous and corrosive sulfuric acid.

NOTICE

(cid:1) Remember that battery and ignition cables carry high currents or volt- ages. Be careful of accidentally causing a short circuit.

(cid:1) Add only “Toyota Super Long Life Coolant” or similar high quality eth- ylene glycol based non−silicate, non−amine, non−nitrite, and non−bo- rate coolant with long−life hybrid organic acid technology to fill the radiator. “Toyota Super Long Life Coolant” is a mixture of 50% cool- ant and 50% deionized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).

(cid:1) If you spill some of the coolant, be sure to wash it off with water to prevent it from damaging the parts or paint.

(cid:1) Do not allow dirt or anything else to fall through the spark plug holes. (cid:1) Do not pry the outer electrode of a spark plug against the center elec- trode.

2007 4Runner from Aug. ’06 Prod. (OM35866U)

415

06 06.07

(cid:1) Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.

(cid:1) Do not reuse iridium−tipped spark

plugs by cleaning or regapping.

(cid:1) Do not overfill automatic transmis- sion fluid, or the transmission could be damaged.

(cid:1) Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.

(cid:1) Be careful not to scratch the glass

surface with the wiper frame.

(cid:1) When closing the engine hood, check to see that you have not for- gotten any tools, rags, etc.

Parts and tools Here is a list of parts and tools you will need to perform do−it−yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. CHECKING THE ENGINE OIL LEVEL Parts (if level is low): (cid:2) “Toyota Genuine Motor Oil” or equiva-

lent See page 421 in Section 7−2 for de- tails about engine oil selection.

Tools: (cid:2) Rag or paper towel (cid:2) Funnel (only for adding oil) CHECKING THE ENGINE COOLANT LEVEL Parts (if level is low): (cid:2) “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−ni- trite, and non−borate coolant with long− life hybrid organic acid technology. “Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion- ized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).

Tools: (cid:2) Funnel (only for adding coolant) CHECKING BRAKE FLUID Parts (if level is low): (cid:2) SAE J1703 or FMVSS No.116 DOT 3

brake fluid

Tools: (cid:2) Rag or paper towel (cid:2) Funnel (only for adding fluid) CHECKING POWER STEERING FLUID Parts (if level is low): (cid:2) Automatic

transmission

fluid

DEXRON(cid:3)II or III

Tools: (cid:2) Rag or paper towel (cid:2) Funnel (only for adding fluid) CHECKING BATTERY CONDITION Tools: (cid:2) Warm water (cid:2) Baking soda (cid:2) Grease (cid:2) Conventional wrench

(for

terminal

clamp bolts)

416

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

CHECKING AND REPLACING FUSES Parts (if replacement is necessary): (cid:2) Fuse with same amperage rating as

original

ADDING WASHER FLUID Parts: (cid:2) Water (cid:2) Washer fluid containing antifreeze (for

winter use)

Tools: (cid:2) Funnel REPLACING LIGHT BULBS Parts: (cid:2) Bulb with same number and wattage rating as original in “Replacing light bulbs” on page 438 in Section 7−3.)

charts

(See

Tools: (cid:2) Screwdriver

2007 4Runner from Aug. ’06 Prod. (OM35866U)

417

06 06.07

418

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

SECTION 7− 2

DO−IT−YOURSELF MAINTENANCE Engine and Chassis Checking the engine oil level Checking the engine coolant level Checking the radiator and condenser Checking brake fluid Checking power steering fluid Checking tire inflation pressure Checking and replacing tires Rotating tires Installing snow tires and chains Replacing wheels Aluminum wheel precautions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

420
422
423
423
424
425
427
429
430
431
432

2007 4Runner from Aug. ’06 Prod. (OM35866U)

419

06 06.07

Checking the engine oil level

Low level

Full level

Z72112

Add oil

O.K.

Too full

4.0 L V6 (1GR−FE) engine

Low level

Full level

Z72111

With the engine at operating tempera- ture and turned off, check the oil level on the dipstick. 1. To get a correct reading, the vehicle should be on level ground. After turning off the engine, wait a few minutes for the oil to drain back into the bottom of the engine.

2. Pull the dipstick out, hold a rag under

the end and wipe it clean.

3. Reinsert the dipstick—push it in as far as it will go, or the reading will not be correct.

4. Pull the dipstick out and look at the oil the

level while holding a rag under end.

CAUTION

Be careful not to touch the hot ex- haust manifold.

NOTICE

If the oil level is below or only slightly above the low level, add engine oil of the same type as already in the engine. Remove the oil filler cap and add engine oil in small quantities at a time, checking the dipstick. We recommend that you use a funnel when adding oil. The approximate quantity of oil needed to raise the level between low and full on the dipstick is indicated as follows:

1.5 L (1.6 qt., 1.3 Imp. qt.)

For the engine oil capacity, see “Service specifications” on page 447 in Section 8. When the level reaches within the correct range, install the filler cap hand−tight.

NOTICE

(cid:1) Be careful not to spill engine oil on

the vehicle components.

(cid:1) Avoid overfilling, or the engine

could be damaged.

(cid:1) Check the oil level on the dipstick

once again after adding the oil.

Add oil

O.K.

Too full

Be careful not to drop engine oil on the vehicle components.

4.7 L V8 (2UZ−FE) engine

420

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

ENGINE OIL SELECTION “Toyota Genuine Motor Oil” in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to grade and viscosity. Oil grade:

following

is used

satisfy

the

is not available, SAE If SAE 5W−30 10W−30 may be used. However, it should be replaced with SAE 5W−30 at the next oil change.

ILSAC multigrade engine oil

Recommended viscosity:

SAE 5W−30

OIL008

Outside temperature

SAE 5W−30 is the best choice for good fuel economy and good starting in cold weather.

Oil identification mark The ILSAC (International Lubricant Stan- dardization and Approval Committee) Certi- fication Mark is added to some oil con- tainers the oil you should use.

to help you select

2007 4Runner from Aug. ’06 Prod. (OM35866U)

421

06 06.07

To ensure excellent lubrication perfor- mance for your engine, “Toyota Genuine Motor Oil” is available, which has been specifically for all Toyota engines. Please contact your Toyota dealer for fur- ther details about “Toyota Genuine Motor Oil”.

tested and approved

type, see “Coolant

Checking the engine coolant level Look at the see−through coolant reser- voir when the engine is cold. The cool- ant level is satisfactory if it is between the “F” and “L” lines on the reservoir. If the level is low, add the coolant. (For the coolant type selection” described below.) The coolant level in the reservoir will vary with engine temperature. However, if the level line, add coolant. Bring the level up to the “F” line. If the coolant level drops within a short time after replenishing, there may be a leak the radiator, hoses, radiator cap and drain cock and water pump. If you can find no leak, have your Toyota dealer test the cap pressure and check for leaks in the cooling system.

the system. Visually check

is on or below

the “L”

in

CAUTION

is a

hybrid

organic

long−life

improper coolants may damage

Coolant type selection Use of your engine cooling system. Only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−nitrite, and non−borate coolant with long−life technology. (Coolant hybrid organic acid acid with technology low phosphates and organic acids.) For the U.S.A.—“Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deionized water. This coolant pro- vides protection down to about −35(cid:2)C (−31(cid:2)F). For Canada—“Toyota Super Long Life Coolant” is a mixture of 55% coolant and 45% deionized water. This coolant pro- vides protection down to about −42(cid:2)C (−44(cid:2)F).

combination of

To prevent burning yourself, do not remove the radiator cap when the en- gine is hot.

NOTICE

Do not use plain water alone.

422

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

Toyota recommends “Toyota Super Long Life Coolant”, which has been tested to ensure that it will not cause corrosion nor result in malfunction of your engine coolant system with proper usage. “Toyota formulated Super Long Life Coolant” with acid technology and has been specifically designed to avoid engine cooling system malfunction on Toyota vehicles. Please contact your Toyota dealer further details.

is organic

long−life

hybrid

for

Checking the radiator and condenser If any of the above parts are extremely dirty or you are not sure of their condi- tion, take your vehicle to a Toyota dealer.

CAUTION

To prevent burning yourself, be care- ful not to touch the radiator or con- denser when the engine is hot.

NOTICE

To prevent damage to the radiator and condenser, do not perform the work by yourself.

Checking brake fluid

CY72025

reservoir. The

To check the fluid level, simply look at the see−through level should be between the “MAX” and “MIN” lines on the reservoir. It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, it may indicate a serious mechanical prob- lem. If the level is low, add SAE J1703 or FMVSS No.116 DOT 3 brake fluid to the brake reservoir.

2007 4Runner from Aug. ’06 Prod. (OM35866U)

423

06 06.07

Refilling brake fluid: 1. Turn the ignition switch off. 2. Depress the brake pedal more than 20
times (until the brake pedal resistance decreases and pedal travel increases). 3. Remove the reservoir cover by hand. Add brake fluid up to the “MAX” line. If you do not follow the procedure above, the reservoir may overflow. Use only newly opened brake fluid. Once opened, brake fluid absorbs moisture from the air, and excess moisture can cause a dangerous loss of braking.

CAUTION

Take care when filling the reservoir because brake fluid can harm your hands or eyes. If fluid gets on your hands or in your eyes, flush the af- fected area with clean water immedi- ately. If you still feel uncomfortable with your hands or eyes, go to the doctor.

NOTICE

If you spill some of the fluid, be sure to wipe it off to prevent it from dam- aging the parts or paintwork.

Checking power steering fluid

If cold O.K.

Close

If hot O.K.

Open

CY72002

If cold add

If hot add

Check the fluid level through the reser- voir. If necessary, add automatic trans- mission fluid DEXRON(cid:3)II or III. If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little more in frigid temperatures), the fluid is hot (60(cid:2)C—80(cid:2)C or 140(cid:2)F—175(cid:2)F). You may also check the level when the fluid is temperature, 10(cid:2)C—30(cid:2)C or 50(cid:2)F—85(cid:2)F) if the engine has not been run for about five hours.

(about

room

cold

424

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

Clean all dirt from the outside of the res- ervoir tank and look at the fluid level. If the fluid is cold, the level should be in the “COLD” range. Similarly, if it is hot, the fluid level should be in the “HOT” range. If the level is at the low side of either range, add automatic fluid DEXRON(cid:3)II or III to bring the level within the range. To remove the reservoir cap, turn it coun- terclockwise and it, turn it clockwise. After replacing the reser- voir cap, visually check the steering box case, vane pump and hose connections for leaks or damage.

lift up. To reinstall

transmission

CAUTION

The reservoir tank may be hot so be careful not to burn yourself.

NOTICE

Avoid overfilling, or the power steer- ing could be damaged.

Checking tire inflation pressure

CY72026

Keep your tire inflation pressures at the proper level. The recommended cold tire inflation pressures, tire sizes and the com- bined weight of occupants and cargo (vehicle capacity weight) are de- scribed on pages 446 and 451. They are also on the tire and loading infor- mation label. You should check the tire inflation pressure every two weeks, or at least once a month. And do not forget the spare! The for checking tire inflation pressure should be observed: (cid:1) The

instructions

be checked only when the tires are cold. If your vehicle has been parked for at least 3 hours and has not been driven for more than 1.5
km or 1 mile since, you will get an accurate cold tire inflation pres- sure reading.

following

pressure

should

2007 4Runner from Aug. ’06 Prod. (OM35866U)

425

06 06.07

(cid:1) If you cannot adjust the tire pressure when the tires are cold, add 20 to 30 kPa more to the front tires and rear tires than the cold tire pressure, but never exceed the maximum cold tire pressure molded on the tire side- wall.

(cid:1) Always use a tire pressure gauge. The appearance of a tire can be misleading. Besides, tire inflation pressures that are even just a few pounds off can degrade ride and handling.

(cid:1) Do not bleed or reduce tire inflation pressure after driving. It is normal for the tire inflation pressure to be higher after driving. (cid:1) Never exceed the vehicle capac- ity weight. Passenger and lug- gage weight should be located so that the vehicle is balanced.

Tire pressure gauge

CY72019

INSPECTION AND ADJUSTMENT PROCEDURE 1. Remove the tire valve cap. 2. Press the tip of the tire pressure

gauge to the tire valve.

3. Read the pressure using the grad-

uations of the gauge.

4. In case the tire inflation pressure is not within the prescribed range, insert the compressed air from the valve. In case of applying too much air, press the center of the valve and release the air to adjust.

5. After completing the tire inflation pressure measurement and ad- justment, apply soapy water to the valve and check for leakage.

6. Install the tire valve cap. If a gauge and air pump are not avail- able, have your vehicle checked by your Toyota dealer.

CAUTION

Be sure to reinstall the tire valve caps. Without the valve caps, dirt or moisture could get into the valve core and cause air leakage. If the caps have been lost, have new ones put on as soon as pos- sible.

NOTICE

Use only the original valve cap. If any other valve cap is used, it may corrode or melt and be- come difficult or impossible to remove.

426

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

Incorrect tire inflation pressure may waste fuel, reduce the comfort of driv- ing, reduce tire life and make your ve- hicle less safe to drive. If a tire frequently needs refilling, have it checked by your Toyota deal- er.

CAUTION

Keep your tires properly inflated. Otherwise, the following condi- tions may occur and cause an ac- cident resulting in death or seri- ous injuries. Low tire pressure (underinfla- tion)— (cid:1) Excessive wear (cid:1) Uneven wear (cid:1) Poor handling (cid:1) Possibility of blowouts from an

overheated tire

(cid:1) Poor sealing of the tire bead

(cid:1) Wheel deformation and/or tire

separation

(cid:1) A greater possibility of tire

damage from road hazards

High tire pressure (overinfla- tion)— (cid:1) Poor handling (cid:1) Excessive wear (cid:1) Uneven wear (cid:1) A greater possibility of tire

damage from road hazards

Checking and replacing tires

Tread wear indicator

CY72126

CHECKING YOUR TIRES Check the tire’s tread for tread wear indicators. If the indicators show, replace the tires. The loca- tion of tread wear indicators is shown by the “TWI” or “D ” marks, etc., molded on the sidewall of each tire.

2007 4Runner from Aug. ’06 Prod. (OM35866U)

427

06 06.07

The tires on your Toyota have built−in tread wear indicators to help you know when the tires need replace- ment. When the tread depth wears to 1.6 mm (0.06 in.) or less, the indica- tors will appear. If you can see the indicators in two or more adjacent grooves, the tire should be replaced. The lower the tread, the higher the risk of skidding. The effectiveness of snow tires is lost if the tread wears down below 4 mm (0.16 in.). If you have tire damage such as cuts, splits, cracks deep enough to expose the fabric, or bulges indi- cating internal damage, the tire should be replaced. If a tire often goes flat or cannot be properly repaired due to the size or location of a cut or other damage, it should be replaced. If you are not sure, consult with your Toyota dealer.

If air loss occurs while driving, do not continue driving. Driving even a short distance can damage a tire beyond repair. Any tires which are over 6 years old must be checked by a qualified technician even if damage is not obvious. Tires deteriorate with age even if they have never or seldom been used. This applies also to the spare tire and tires stored for future use.

REPLACING YOUR TIRES When replacing a tire, use a tire of the same size and construction, and the same or greater maximum load as the originally installed tires. Also, on four−wheel drive models, all the tires must be the same brand and have the same tread patterns. Using any other size or type of tire may seriously affect handling, ride, speedometer/odometer calibration, ground clearance, and clearance be- tween the body and tires or snow chains. Check that the maximum load of the replaced tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater. As for the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire, and as for the Gross Axle Weight Ratings (GAWR), see the Cer- tification Label.

428

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

For details about the side wall of the tire and the Certification Label, see pages 339 and 342.

CAUTION

Observe the following instruc- tions. Otherwise, an accident may occur resulting in death or serious injuries. (cid:1) Do not mix radial, bias belted, or bias−ply tires on your ve- hicle, as this may cause dan- gerous handling characteris- tics resulting in loss of control. (cid:1) Do not use tires other than the manufacturer’s recommended size, as this may cause danger- ous handling characteristics resulting in loss of control.

(cid:1) Four−wheel drive models:

Do not use tires of different brands, sizes, construction or tread patterns, as this may cause dangerous handling characteristics in loss of control.

resulting

Toyota recommends all four tires, or at least both of the front or rear tires be replaced at a time as a set. See “If you have a flat tire” on page 379 for tire change procedure. When a tire is replaced, the wheel should always be balanced. An unbalanced wheel may affect ve- hicle handling and tire life. Wheels can get out of balance with regular use and should therefore be balanced occasionally. When replacing a tubeless tire, the air valve should also be replaced with a new one.

Rotating tires

CY72009

tire

life,

(For

To equalize the wear and help extend Toyota recommends that you rotate your tires according to the maintenance schedule. scheduled maintenance information, please refer “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.) However, the most appropriate timing for tire rotation may vary according to your driving habits and road surface conditions.

the

to

2007 4Runner from Aug. ’06 Prod. (OM35866U)

429

06 06.07

See “If you have a flat tire” on page 379 in Section 4 for tire change proce- dure. When rotating tires, check for uneven wear and damage. Abnormal wear is usually caused by incorrect tire pres- sure, improper wheel alignment, out− of−balance wheels, or severe braking.

Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select tires of the same size, construction and load capacity as the originally installed tires. Also, on four−wheel drive models, all the tires must be the same brand and have the same tread patterns. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions.

CAUTION

the

following

Observe instructions. Otherwise, an accident may occur re- sulting in death or serious injuries. (cid:1) Do not use snow tires other than the manufacturer’s recommended si- ze, as this may cause dangerous handling characteristics resulting in loss of control.

(cid:1) Four−wheel drive models:

Do not use snow tires of different brands, sizes, construction or tread patterns, as this may cause danger- ous handling characteristics result- ing in loss of control.

SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the front wheels only can lead to an excessive difference in road grip capability between the front and rear tires which could cause loss of vehicle control. When storing removed tires, you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replacing.

CAUTION

(cid:1) Do not drive with the snow tires

incorrectly inflated.

(cid:1) Never drive over 120 km/h (75 mph)

with any type of snow tires.

430

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

TIRE CHAIN SELECTION Use the tire chains of correct size. Regulations regarding the use of tire chains vary according to location or type of road, so always check local reg- ulations before installing chains. CHAIN INSTALLATION Install the chains on the rear tires as tightly as possible. Do not use tire tires. Retighten chains on chains after km (1/4—1/2 mile). When installing chains on your tires, care- fully follow the instructions of the chain manufacturer. If wheel covers are used, they will be scratched by the chain band, so remove the covers before putting on the chains.

front driving

0.5—1.0

the

CAUTION

(cid:1) Do not exceed 50 km/h (30 mph) or recom- is

the chain manufacturer’s mended speed lower.

limit, whichever

(cid:1) Avoid sharp turns or locked−wheel braking, as use of chains may ad- versely affect vehicle handling.

(cid:1) When driving with chains installed, to drive carefully. Slow be sure down before entering curves to avoid losing control of the vehicle. Otherwise an accident may occur.

Replacing wheels WHEN TO REPLACE YOUR WHEELS If you have wheel damage such as bending, cracks or heavy corrosion, the wheel should be replaced. If you fail to replace a damaged wheel, the tire may slip off the wheel or cause loss of handling control. WHEEL SELECTION When replacing wheels, care should be taken to ensure that the wheels are re- placed by ones with the same load ca- pacity, diameter, rim width, and offset. Correct replacement wheels are available at your Toyota dealer. A wheel of a different size or type may adversely affect handling, wheel and bear- ing life, brake cooling, speedometer/odom- eter calibration, stopping ability, headlight aim, bumper height, vehicle ground clear- ance, and tire or snow chain clearance to the body and chassis.

(cid:1) Drive carefully avoiding bumps, holes, and sharp turns, which may cause the vehicle to bounce.

2007 4Runner from Aug. ’06 Prod. (OM35866U)

431

06 06.07

Replacement with used wheels is not rec- ommended as they may have been sub- jected to rough treatment or high mileage and could fail without warning. Also, bent wheels which have been straightened may have structural damage and therefore should not be used. Never use an inner tube in a leaking wheel which is designed for a tubeless tire.

CAUTION

the

following

instructions. Observe Otherwise, an accident may occur re- sulting in death or serious injuries. (cid:1) Do not use wheels other than the manufacturer’s recommended size, as this may cause dangerous han- dling characteristics in loss of control.

resulting

Aluminum wheel precautions (cid:1) When aluminum wheels, check tight after driving your vehicle the first 1600
km (1000 miles).

the wheel nuts are

installing that

(cid:1) If

repaired or you have changed your the wheel nuts are still tight after driving 1600 km (1000 miles).

rotated, tires, check

that

(cid:1) When using tire chains, be careful not

to damage the aluminum wheels.

(cid:1) Use only Toyota wheel nuts and for your aluminum

wrench designed wheels.

(cid:1) When balancing your wheels, use only Toyota balance weights or equivalent and a plastic or rubber hammer.

(cid:1) As with any wheel, periodically check your aluminum wheels for damage. If damaged, replace immediately.

(cid:1) Four−wheel drive models:

Do not use wheels of different brands, sizes and types, as this may cause dangerous handling characteristics resulting in loss of control.

432

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

SECTION 7− 3

DO−IT−YOURSELF MAINTENANCE Electrical components Checking battery condition Battery recharging precautions Checking and replacing fuses Adding washer fluid Replacing light bulbs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

434
435
436
437
438

2007 4Runner from Aug. ’06 Prod. (OM35866U)

433

06 06.07

Checking battery condition— —Precautions

CAUTION

BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas. (cid:1) Do not cause a spark from the bat-

tery with tools.

(cid:1) Do not smoke or light a match near

the battery.

The electrolyte contains poisonous and corrosive sulfuric acid. (cid:1) Avoid contact with eyes, skin or

clothes.

(cid:1) Never ingest electrolyte. (cid:1) Wear protective safety glasses when

working near the battery.

(cid:1) Keep children away from the bat-

tery.

EMERGENCY MEASURES (cid:1) If electrolyte gets

in your eyes, flush your eyes with clean water immediately immediate medical attention. If possible, con- tinue to apply water with a sponge or cloth while en route to the medi- cal office.

and get

(cid:1) If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medi- cal attention immediately.

(cid:1) If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.

(cid:1) If you accidentally swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.

—Checking battery exterior

Terminals

CY73024

Ground cable

Hold−down clamp

Check the battery for corroded or loose terminal connections, cracks, or loose hold−down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.

b. If the terminal connections are loose, their clamp nuts—but do not

tighten overtighten.

c. Tighten

the hold−down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.

434

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

NOTICE

(cid:1) Be sure the engine and all accesso- ries are off before performing main- tenance.

(cid:1) When checking the battery, remove the ground cable from the negative terminal (“−” mark) first and rein- stall it last.

(cid:1) Be careful not to cause a short cir-

cuit with tools.

(cid:1) Take care no solution gets into the

battery when washing it.

If the battery is disconnected or run down, the power window, power back win- dow and moon roof may not operate auto- matically, the jam protection function will not function correctly, and the back door will not open after you reconnect, replace or recharge the battery. In any of these cases, you should normalize the power window, power back window, back door and moon roof. To normalize them, see “Power windows” on page 27, “Power back window” on page 30, “Back door” on page 32 and “Electric moon roof” on page 39
in Section 1−2.

—Checking battery condition

Type A

Green

Dark

Clear or light yellow

CY73015

Type B

Blue

White

Red

CHECKING BY INDICATOR Check the battery condition by the indi- cator color.

Indicator color

Type A

Type B

Green

Blue

Dark

White

Condition Condition

Good

Charging necessary. Have battery checked by your Toyota dealer.

Battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.

2. Be sure the power switch on the re- charger the charger cables to the battery and when disconnecting them.

is off when connecting

CAUTION

(cid:1) Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.

(cid:1) Only do a slow charge (5 A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.

NOTICE

Clear or

light yellow

Red

Have battery checked by your Toyota dealer.

Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.

2007 4Runner from Aug. ’06 Prod. (OM35866U)

435

06 06.07

Checking and replacing fuses

Type A

Good

Blown

Type B

CY73023

Good

Blown

Type C

Good

Blown

CY73033

If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations” on page 414 in Sec- tion 7−1 for locations of the fuses. Turn the ignition switch and inoperative component off. Pull the suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See page 452 in Section 8 for the functions controlled by each circuit.

Type A fuses can be pulled out by using the pull−out tool. The location of the pull− out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency you can pull out the “PWR OUTLET” or “HEATER NO.2” fuse, which may be dispensable for normal driving, and use it if its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower, but as close to the rating as possible. If the amperage is fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies.

that specified,

lower

than

the

436

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

the new

If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your Toyota dealer correct it as soon as possible.

CAUTION

Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.

Adding washer fluid

CY73025

You may use plain water as washer fluid. However, in cold areas where tempera- tures range below the freezing point, use washer fluid containing antifreeze. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

If any washer does not work, the wash- er tank may be empty. Check the wash- er fluid level on the level gauge. If the washer fluid level is below “LOW” or only slightly above the “LOW” level, add washer fluid. For vehicles sold in Canada— If any washer does not work or low windshield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid.

2007 4Runner from Aug. ’06 Prod. (OM35866U)

437

06 06.07

following

illustrations show how

Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table. The stop/tail and rear side marker lights consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light re- placed.

CAUTION

(cid:1) To prevent burning yourself, do not replace the light bulbs while they are hot.

(cid:1) Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.

NOTICE

Only use a bulb of the listed type.

the

The inside of the lens of exterior lights such as headlights may temporarily fog up when the lens becomes wet in the rain or in a car wash. This is not a problem because the is caused by fogging temperature difference between the outside and the windshield fogs up in the rain. However, if there large drop of water on the inside of the lens, or if there is water pooled light, contact your Toyota dealer.

inside of

inside

lens,

is a

just

like

the

the

438

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

A: HB3 halogen bulbs B: H11 halogen bulbs C: HB4 halogen bulbs D: Wedge base bulbs (amber) E: Single end bulbs F: Wedge base bulbs (clear) G: Double end bulbs

Light bulbs

Headlights (high beam) Headlights (low beam) Front fog lights Parking and front side marker lights Front turn signal lights Rear turn signal lights Back−up lights License plate lights High mounted stoplight Interior light Personal lights Vanity lights Door courtesy lights Glove box light Luggage compartment light Running board lights

Bulb No.

9005

—

9006
168

1156NA

— 921
168
921
— — — — — — —

60
55
51
27
21
18
18
3.8
1.2
3.8

Type

2007 4Runner from Aug. ’06 Prod. (OM35866U)

439

06 06.07

—Headlights

Low beam (outside)

CY73039

CY73004

CY73040

High beam (inside)

1. Turn the bulb base counterclockwise to the front of the vehicle as shown.

2. Unplug the connector while depress-

ing the lock release.

If the connector is tight, wiggle it.

3. Install a new bulb and connector into turn them clockwise to the front of the vehicle.

the mounting hole and

Aiming is not necessary after replacing the bulb. When aiming adjustment is nec- essary, contact your Toyota dealer.

440

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

—Front fog lights

CY73041

CY73009

CY73042

1. Turn the bulb base counterclockwise to the front of the vehicle as shown.

2. Unplug the connector while depress-

ing the lock release.

If the connector is tight, wiggle it.

3. Install a new bulb and connector into turn them clockwise to the front of the vehicle.

the mounting hole and

2007 4Runner from Aug. ’06 Prod. (OM35866U)

441

06 06.07

—Parking and front side marker lights

—Front turn signal lights

—Rear turn signal and back−up lights

CY73043

CY73045

CY73047

Use a wrapped with a cloth.

flathead screwdriver which

is

CY73044

CY73046

CY73048

442

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

—License plate lights

—High mounted stoplight

Clips

CY73049

CY73028

CY73030

a: Rear turn signal light b: Back−up light

Use a Phillips−head screwdriver.

Disconnect the clips by using a flathead screwdriver which is wrapped with a cloth.

CY73029

2007 4Runner from Aug. ’06 Prod. (OM35866U)

443

06 06.07

CY73031

CY73032

444

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

SECTION 1− 10

OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Multi−information display Compass Rear view monitor system Power outlet Glove box Garage door opener Auxiliary boxes Rear console box Tissue box holder Coin holder Trash holder Front cup holders Rear cup holders and tray Rear cup holders Bottle holders Tie−down hooks Grocery bag hooks Cargo net hooks Luggage cover Double deck Roof luggage carrier Floor mat

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

294
297
302
305
307
308
312
314
315
316
316
317
318
320
320
321
321
322
322
323
324
326

2007 4Runner from Aug. ’06 Prod. (OM35866U)

293

06 06.07

Multi−information display—

1. “RESET” button 2. “MODE” button 3. Air conditioning system without “DUAL”

button—Cruise information display Air conditioning system with “DUAL” button—Outside temperature and cruise information display

4. Clock 5. Air conditioning system without “DUAL”

button only—Outside temperature display

6. “:00” button 7. “M” button 8. “H” button

CY19124y

294

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

the

ignition switch

the multi−information display

—Before using the multi−information display Operate with the ignition switch on. to When “ON”, the last previously used mode dis- played just before the ignition switch is turned off will appear. If the electrical power source has been disconnected the multi−information display, the display will automatically be set to the initial mode.

turned

from

is

CAUTION

Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

—Clock

—Outside temperature display (air conditioning system without “DUAL” button)

CY19001

CY19082

the

time

To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. If quick adjustment to a full hour is de- sired, push the “:00” button. if the “:00” button is de- For example, pressed when is between 1:01—1:29, the time will change to 1:00. If the time will change to 2:00. The key must be in the “ACC” or “ON” position. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00 (one o’clock).

is between 1:30—1:59,

time

the

from

temperature

the outside air

The displayed ranges −30(cid:4)C (−22(cid:4)F) up to 50(cid:4)C (122(cid:4)F). The key must be in the “ON” position. If an abnormality exists in the connection of temperature sensor, “−−(cid:4)C” (“−−(cid:4)F”) will appear on the display. If “−−(cid:4)C” (“−−(cid:4)F”) appears on the display, contact your Toyota dealer. There may be a case that “−−(cid:4)C” (“−−(cid:4)F”) appears momentarily when the ignition is quickly turned to “ON”. It is normal if it goes out soon.

2007 4Runner from Aug. ’06 Prod. (OM35866U)

295

06 06.07

—Cruise information display

Air conditioning system with “DUAL” button only—

CY19121

temperature display

The outside (air conditioning system with “DUAL” but- ton) and cruise information display indi- cates the following information. Every time you push the “MODE” but- ton, the display toggles through this information. 1. Outside temperature 2. Driving range 3. Average fuel consumption 4. Average vehicle speed 5. Display off The displayed values in the cruise infor- mation display indicate general driving conditions. Accuracy varies with driving habits and road conditions.

1. Outside temperature (“OUTSIDE (cid:4)F”

or “OUTSIDE (cid:4)C”)

from

temperature

the outside air

The displayed value is updated every 1
second. The displayed ranges −30(cid:4)C (−22(cid:4)F) up to 50(cid:4)C (122(cid:4)F). If an abnormality exists in the connection of temperature sensor, “−−(cid:4)C” (“−−(cid:4)F”) will appear on the display. If “−−(cid:4)C” (“−−(cid:4)F”) appears on the display, contact your Toyota dealer. There may be a case that “−−(cid:4)C” (“−−(cid:4)F”) appears momentarily when the ignition is quickly turned to “ON”. It is normal if it goes out soon.

296

2007 4Runner from Aug. ’06 Prod. (OM35866U)

06 06.07

2. Driving range

(“RANGE MI” or “RANGE km”)

3. Average fuel consumption

(“AVG. MPG” or “AVG. L/100 km”)

Compass

It

the

fuel

indicates

fuel gauge reaches “E”.

The distance the vehicle can travel with the remaining is calculated and displayed based on the quantity of re- maining fuel and past fuel consumption. The driving range display the approximate distance that you can drive until is different from the actual distance traveled. The displayed value is updated about ev- ery 10 seconds. Every time you refuel the vehicle, the cal- culation is reset. The actual driving range varies with driv- ing habits and road conditions. If fuel con- sumption is good, the driving range will be longer than indicated. If fuel consumption is poor, the driving range will be shorter than indicated. If the low fuel level warning light comes on, refuel the vehicle even if the display indicates that the vehicle can be driven further.

total

Average fuel consumption is calculated and displayed based on total driving distance and fuel consumption with the engine running. The displayed value is updated about ev- ery 10 seconds. To the “RESET” button about 1 second. 4. Average vehicle speed

calculation,

reset

push

the

(“AVG. MPH” or “AVG. km/h”)

Average vehicle speed is calculated and displayed based on total driving dis- tance and total driving time with the engine running. The displayed value is updated about ev- ery 10 seconds. To the “RESET” button about 1 second.

calculation,

reset

push

the

CY19138

The direction is indicated on the inside rear view mirror. If the ignition switch was turned off with the system on, the system will automati- cally turn back on when the ignition switch is turned on.

” switch for longer than 3
Push the “ seconds turn the compass system on and off.

2007 4Runner from Aug. ’06 Prod. (OM35866U)

297

06 06.07

indicates

the vehicle

the direction The compass that the above case, it shows that the vehicle is heading north.

is heading.

In

Displays

NE SE SW NW

Directions

North

Northeast

East

Southeast

South

Southwest

West

Northwest

The compass may not show the correct direction in the following conditions: (cid:2) The vehicle is stopped immediately af-

ter turning.

(cid:2) The compass does not adjust while the

vehicle is stopped.

(cid:2) The ignition switch is turned off imme-

diately after turning.

(cid:2) The vehicle is on an inclined surface.

(cid:2) The vehicle is in a place where the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

(cid:2) The vehicle is magnetized. (There is a magnet or a metal object on or near the inside rear view mirror.)

CY19139

the deviation