...
.................................................................... 2-22
.................................................................... 2-27
Security systems ...
.................................................. 2-27
........................... 2-28
............................... 2-30
........................... 2-31
Checking bulbs ... Warning lights ... Indicator lights ... Audible reminders ...
Windshield wiper and washer switch ... Rear window wiper and washer switch ...
Operational indicators ... Maintenance indicators ... Trip computer
Vehicle security system ... NISSAN vehicle immobilizer system ...
Dot matrix liquid crystal display ...
...
...
...
Rear window and outside mirror defroster switch ... Headlight and turn signal switch ...
Xenon headlights (if so equipped) Headlight switch ... Turn signal switch ... Fog light switch (if so equipped)
Hazard warning flasher switch ... Horn ... Heated seats (if so equipped) Blind Spot Warning (BSW) switch (if so equipped) Vehicle Dynamic Control (VDC) OFF switch ... Power outlet Storage ...
....... 2-32
....................................... 2-32
...
............................ 2-32
............................................................ 2-33
.......................................................... 2-37
...
.............................. 2-37
........................................... 2-37
.......................................................................................... 2-38
........................................... 2-38
..... 2-40
................. 2-40
............................................................................ 2-41
.................................................................................... 2-43
..................................................................... 2-43
Cup holders ...
.......................... 2-45
Sunglasses holder (if so equipped)
......................................................................... 2-46
Glove box
...
..................... 2-46
Instrument lower box (if so equipped)
...
.................................................................... 2-46
Console box
............................................................... 2-47
Cargo floor box
................................................................................ 2-48
Hooks ...
Roof rack (if so equipped)
...
.......................................... 2-49
...................................................................... 2-50
Coat hooks ...
................................................. 2-50
................................................................................. 2-51
.............................................................. 2-51
Sunshade (if so equipped) Windows ...
Power windows ...
...
...
...
...
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (80,1)
...
Cargo lights ... HomeLink® Universal Transceiver (if so equipped)
............................................................................ 2-58
...... 2-59
............................................. 2-59
.................................................... 2-61
Programming HomeLink® ... Programming HomeLink® for Canadian Customers ... Operating the HomeLink® Universal Transceiver Programming trouble-diagnosis ... Clearing the programmed information ... Reprogramming a single HomeLink® button ... If your vehicle is stolen ...
.................................................... 2-61
...
................................. 2-61
...................... 2-61
.......... 2-61
................................................. 2-62
...
Automatic moonroof Front moonroof Rear moonroof If the front or rear moonroof does not operate ...
................................................... 2-53
Moonroof (if so equipped)
...
........................................................ 2-53
................................................................. 2-54
...
.................................................................. 2-54
...
........ 2-55
.......................................................................... 2-56
...
........................................................................... 2-56
Map lights ...
Rear personal lights ...
......................................................... 2-56
............................................ 2-57
Interior light control switch ...
.............................................................................. 2-58
................................................................. 2-58
Mood lights ... Vanity mirror lights ...
Interior lights
[ Edit: 2011/ 10/ 27 Model: E52-D ]
COCKPIT
GUID-DCC2794A-4B62-4A96-BA3A-A529DCB296EE
1. 2.
3. 4. 5. 6.
Vehicle Dynamic Control (VDC) OFF switch Blind Spot Warning (BSW) switch* — Blind Spot Warning (BSW)* Sliding door switch* (driver’s side) Sliding door switch* (passenger’s side) Instrument brightness control switch Power lift gate switch*
Black plate (81,1)
Fuse box cover Fuel-filler door opener handle
11. 12. 13. Hood release handle 14. Headlight aiming control* 15. Power door main switch* 16. Steering-wheel-mounted controls (left side)
— Audio control steering switch* — Hands-Free Phone System switch*
17. Horn 18. Steering-wheel-mounted controls (right side)
— Cruise control system if so equipped
*:
SSI0825
7.
Headlight, fog light and turn signal switch — Headlight — Turn signal — Fog light* Trip computer switch TRIP/RESET switch for twin trip odometer
8. 9. 10. Wiper and washer switch
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Instruments and controls 2-3
Black plate (82,1)
Tilting telescopic steering wheel lever Front passenger air bag status light
10. Heater/air conditioner control or audio system 11. Parking brake 12. 13. 14. Heated seat switch* 15. Cup holders 16. Power outlet 17. 18. Power outlet main switch* 19. Audio system 20. Glove box *: **:
if so equipped Refer to the separate Navigation System Own- er’s Manual (if so equipped).
Instrument lower box or CD/DVD slot
INSTRUMENT PANEL
GUID-0C8F786C-EE91-435E-980B-4A330DFE7B46
1. 2. 3. 4. 5. 6.
Side ventilator Meters and gauges Push-button ignition switch Hazard warning flasher switch Selector lever Center display — Center color display*
2-4 Instruments and controls
SSI0824
— Navigation system** Center multi-function control panel* — Navigation system** — Vehicle information and setting buttons* Rear window and outside mirror* defroster switch Center ventilator
7.
8.
9.
[ Edit: 2011/ 10/ 27 Model: E52-D ]
METERS AND GAUGES
GUID-37D11D36-26FF-4EBB-A6F1-92389D9391F7
Black plate (83,1)
OFF position. This is not a malfunction.
METER/RING ILLUMINATION AND
NEEDLE SWEEP
GUID-6FB96EED-2227-43A8-9F52-B32907E5E8C9
The ring illumination surrounding meters and
gauges illuminates when the driver’s door is
closed after getting into the vehicle with the
Intelligent Key carried in.
When the engine is started,
the indicator
needles will sweep in the speedometer and
tachometer and the ring illumination will be
brightened gradually. This function can be
turned off. (See “Trip computer” (P.2-22).)
JVC0210X
Instrument brightness control switch Tachometer Speedometer Fuel gauge
1. 2. 3. 4. 5. Warning/indicator lights 6. 7.
Trip computer switch Dot matrix liquid crystal display
8. 9.
— Trip computer Engine coolant temperature gauge Odometer/twin trip odometer/Continuously Vari- able Transmission (CVT) position indicator TRIP/RESET switch for twin trip odometer
10. The needle indicators may move slightly after the ignition switch is pushed to the
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Instruments and controls 2-5
Black plate (84,1)
Resetting the trip odometer:
Pushing the TRIP RESET switch *3
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
for more
than 1 second resets the trip odometer to zero.
Speedometer
Odometer/twin trip odometer
JVI0252X
SIC4632
SPEEDOMETER AND ODOMETER
GUID-77958C18-38E6-4515-81A8-602B476070B8
Speedometer
GUID-149DA615-AB5B-4172-8BCC-7CBFBA50FC98
The speedometer indicates vehicle speed in
miles per hour (MPH) and kilometers per hour
(km/h).
2-6 Instruments and controls
GUID-2708C880-F080-4F4D-98C7-A14C9193EC2E
Odometer/twin trip odometer
and twin trip odometer *2
The odometer *1
are displayed when the ignition switch is in the
ON position.
The odometer records the total distance the
vehicle has been driven.
The twin trip odometer records the distance of
individual trips.
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Changing the display: Pushing the TRIP RESET switch *3 on the right side of the combination meter panel changes the display as follows: TRIP A ? TRIP B ? TRIP A
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (85,1)
normal range, reduce vehicle speed to decrease temperature. If gauge is over the normal range, stop the vehicle as soon as safely possible and let the engine idle. If the engine is overheated, continued operation of the vehicle may seriously damage the engine. See “If your vehicle overheats” (P.6-11) for immediate action required.
JVI0253X
SIC4634
TACHOMETER
GUID-79F10C98-2BE5-4F74-A188-74BAA5909F72
The tachometer
indicates engine speed in
revolutions per minute (RPM). Do not rev the
engine into the red zone *1 .
CAUTION
When engine speed approaches the red zone, shift to a higher gear or reduce engine speed. Operating the engine in the red zone may cause serious engine damage.
ENGINE COOLANT TEMPERATURE
GAUGE
GUID-003147DA-54F3-4A22-B149-F2BA3D91601C
The gauge indicates the engine coolant tem-
perature.
The engine coolant temperature is within the
normal range when the gauge needle points
within the zone *1
The engine coolant temperature varies with the
outside air temperature and driving conditions.
shown in the illustration.
CAUTION
If the gauge indicates engine coolant temperature near the hot (H) end of the
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Instruments and controls 2-7
Black plate (86,1)
COMPASS (if so equipped)
GUID-0243F401-24D2-408A-8B8E-8C72A3383AB8
SIC3181
When the ignition switch is pushed to the ON position, the compass display *B will indicate the direction of the vehicle’s heading.
NOS1741
If the display reads “C”, calibrate the compass by driving the vehicle in 3 complete circles at less than 5 MPH (8 km/h). You can also calibrate the compass by driving your vehicle
“0”. There will be a small reserve of fuel in the tank when the fuel gauge needle reaches “0”. The located on the driver’s side of the vehicle.
indicates that the fuel-filler door is
CAUTION
If the vehicle runs out of fuel, the malfunction indicator light (MIL) may come on. Refuel as soon as possible. After a few driving trips, the light should turn off. If the light remains on after a few driving trips, have the vehicle inspected by a NISSAN dealer.
. For additional
information, see “Malfunction Indicator Light (MIL)” (P.2-17).
[ Edit: 2011/ 10/ 27 Model: E52-D ]
JVI0357X
FUEL GAUGE GUID-4FD368E8-40E3-43E2-835D-44E9D00DBB7A The gauge indicates the approximate fuel level in the tank. The gauge may move slightly during braking, turning, acceleration, or going up or down hills. The gauge needle returns to “0” (empty) after the ignition switch is pushed to the OFF position. Refill the fuel registers “0” (empty). The low fuel warning appears on the dot matrix liquid crystal display when the fuel level in the tank is getting low. Refuel as soon as it is convenient, preferably before the gauge reaches
tank before the gauge
2-8 Instruments and controls
Black plate (87,1)
on your everyday route. The compass will be calibrated once it has tracked 3 complete circles. To turn on and off the compass manually, push switch *A while the ignition switch is in the the ON position.
Zone map
SIC0611B
Instruments and controls 2-9
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (88,1)
ZONE VARIATION CHANGE PROCE-
DURE
GUID-C6F3B83E-5981-4619-BFBA-90E24463C307
The difference between magnetic north and
geographical north is known as variance.
In
some areas, this difference can sometimes be
great enough to cause false compass readings.
Follow these instructions to set the variance for
your particular location if this happens:
1. Push the
switch for more than 3
seconds. The current zone number will
appear in the display.
2. Find your current
location and variance
number on the zone map. NOTE: Use zone number 5 for Hawaii.
pass point when the vehicle moves to an area where the geomagnetism is stabilized.)
CAUTION
. Do not install a ski rack, antenna, etc., which are attached to the vehicle by means of a magnet. They affect the operation of the compass. . When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as it may cause the liquid cleaner to enter the mirror housing.
3. Push the
switch repeatedly until the new zone number appears in the display, then release the switch. After you release the switch, the display will show a compass direction within a few seconds.
If the compass deviates from the correct indication soon after repeated adjust- ment, have the compass checked at a NISSAN dealer.
. The compass may not
indicate the correct compass point in tunnels or while driving up or down a steep hill.
(The compass returns to the correct com-
2-10 Instruments and controls
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (89,1)
WARNING/INDICATOR LIGHTS AND AUDIBLE REMINDERS
GUID-E5FC8490-7919-41ED-A4B5-0EDA211CD359
Anti-lock Braking System (ABS) warning light
Brake warning light
Blind Spot Warning (BSW) system warning light*
Charge warning light
Engine oil pressure warning light
Hydraulic pump electric power steering warning light
Intelligent Key system warning light
Exterior light indicator
Low tire pressure warning light
Front passenger air bag status light
Master warning light
High beam indicator light
Seat belt warning light and chime
Malfunction Indicator Light (MIL)
Supplemental air bag warning light
Overdrive off indicator light
Vehicle Dynamic Control (VDC) warning light Continuously Variable Transmission (CVT) position indicator light
Cruise indicator light
Security indicator light
Turn signal/hazard indicator lights
Vehicle Dynamic Control (VDC) off indicator light
*: if so equipped
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Instruments and controls 2-11
Black plate (90,1)
and perform the following: 1. Check the brake fluid level. Add brake fluid as necessary. (See “Brake fluid” (P.8-12).) If the brake fluid level is correct, have the warning system checked by a NISSAN dealer.
2.
Anti-lock Braking System (ABS) warning
indicator:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the parking brake is released and the
brake fluid level
is sufficient, if both the brake
warning light and the Anti-lock Braking System
(ABS) warning light illuminate,
it may indicate
the ABS is not functioning properly. Have the
brake system checked, and if necessary re-
paired, by a NISSAN dealer promptly.
(See
“Anti-lock Braking System (ABS) warning light”
(P.2-12).)
WARNING
. Your brake system may not be working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive care- fully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be dangerous.
CHECKING BULBS GUID-417B879A-A92E-4249-868A-0A1EAE9645BC With all doors closed, apply the parking brake and push the ignition switch to the ON position without starting the engine. The following lights will come on (if so equipped):
or
The following lights come on briefly and then go off (if so equipped):
or
If any light does not come on, it may indicate a burned-out bulb or an open circuit in the electrical system. Have the system checked by a NISSAN dealer. Some indicators and warnings are also dis- played on the dot matrix crystal display on the speedometer. (See “Dot matrix liquid crystal display” (P.2-18).)
2-12 Instruments and controls
WARNING LIGHTS
GUID-0B8BE9BD-DD2D-42CD-9609-77C89F9DAADE
or
Anti-lock Braking System
(ABS) warning light GUID-655F063D-167E-412E-A492-9EB6E0A36B2B When the ignition switch is in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates the ABS is operational. If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is not functioning properly. Have the system checked by a NISSAN dealer. If an ABS malfunction occurs, the anti-lock function is turned off. The brake system then operates normally, but without anti-lock assis- tance. (See “Brake system” (P.5-28).)
or
Brake warning light
GUID-D41A90B4-BBBD-4A13-A28B-2B6354F7D9CF This light functions for both the parking brake and the foot brake systems.
Parking brake indicator:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the ignition switch is in the ON position,
the light comes on when the parking brake is
applied.
Low brake fluid warning light:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
When the ignition switch is in the ON position,
the light warns of a low brake fluid level. If the
light comes on while the engine is running with
the parking brake not applied, stop the vehicle
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (91,1)
. Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stop- ping distance and braking will re- quire greater pedal effort as well as pedal travel.
If the brake fluid level is below the minimum or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer.
Blind Spot Warning (BSW) system
warning light (if so equipped)
GUID-6C8CB008-F4A8-4527-8F23-28CFC71360B7
If the light comes on and remains on,
it may
indicate that the BSW system is not functioning
properly. Although the vehicle is still driveable,
have the system checked by a NISSAN dealer.
See “Blind Spot Warning (BSW) system” (P.5-
17).
Charge warning light
GUID-97A46BCC-A033-4C46-B36A-9BA71C57144E If the light comes on while the engine is running, it may indicate the charging system is not functioning properly. Turn the engine off and check the alternator belt. If the belt is loose, broken, missing or if the light remains on, see a NISSAN dealer immediately.
CAUTION
Do not continue driving if the alternator belt is loose, broken or missing.
Engine oil pressure warning light
GUID-C8F5B30A-8F1D-4F15-AA4E-850D2537AEBB This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop. The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. (See “Engine oil” (P.8-8).)
CAUTION
Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost immediately. Such damage is not cov- ered by warranty. Turn off the engine as soon as it is safe to do so.
Hydraulic pump electric power
steering warning light GUID-D4744030-133A-448B-B7CD-0978663FF53F When the ignition switch is in the ON position, the hydraulic pump electric power steering warning light illuminates. After starting the engine, the hydraulic pump electric power steering warning light turns off. This indicates that the electric power steering system is operational. If the hydraulic pump electric power steering warning light illuminates while the engine is running, it may indicate the hydraulic pump electric power steering system is not functioning properly and may need servicing. Have the hydraulic pump electric power steering system checked by a NISSAN dealer. (See “Hydraulic pump electric power steering system” (P.5-28).)
Intelligent Key system warning light GUID-CC2A9148-640E-4118-8267-844E6632CAFD After the ignition switch is pushed to the ON position, this light comes on for about 2 seconds and then turns off. This light warns of a malfunction with the Intelligent Key system. the light comes on while the engine is If stopped, the engine. If the light comes on while the engine is running, you can drive the vehicle. However in these cases, contact a NISSAN dealer for repair
it may be impossible to start
Instruments and controls 2-13
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (92,1)
as soon as possible.
Low tire pressure warning light
GUID-39F496BF-BD8A-42F3-83A3-8010173FD598
Your vehicle is equipped with a Tire Pressure
Monitoring System (TPMS) that monitors the tire
pressure of all tires except the spare.
The low tire pressure warning light warns of low
tire pressure or indicates that the TPMS is not
functioning properly.
After the ignition switch is pushed ON, this light
illuminates for about 1 second and turns off.
the warning light will
Low tire pressure warning:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
the vehicle is being driven with low tire
If
pressure,
illuminate. A
CHECK TIRE PRESSURE warning also appears
on the dot matrix liquid crystal display.
When the low tire pressure warning light
illuminates, you should stop and adjust the tire
pressure to the recommended COLD tire
pressure shown on the Tire and Loading
Information label. The low tire pressure warning
light does not automatically turn off when the tire
pressure is adjusted. After the tire is inflated to
the recommended pressure, the vehicle must be
driven at speeds above 16 MPH (25 km/h) to
activate the TPMS and turn off
the low tire
pressure warning light. Use a tire pressure
gauge to check the tire pressure.
The CHECK TIRE PRESSURE warning is active
2-14 Instruments and controls
as long as the low tire pressure warning light remains illuminated. For additional information, see “Dot matrix liquid crystal display” (P.2-18), “Tire Pressure Mon- itoring System (TPMS)” (P.5-3) and “Tire Pressure Monitoring System (TPMS)” (P.6-2).
TPMS malfunction:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
If the TPMS is not functioning properly, the low
tire pressure warning light will flash for approxi-
mately 1 minute when the ignition switch is
pushed ON. The light will remain on after 1
minute. Have the system checked by a NISSAN
dealer. The CHECK TIRE PRESSURE warning
does not appear if the low tire pressure warning
light illuminates to indicate a TPMS malfunction.
For additional
information, see “Tire Pressure
Monitoring System (TPMS)” (P.5-3). For the
CHECK TIRE PRESSURE warning, see “Dot
matrix liquid crystal display” (P.2-18).
abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with un- der-inflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If the light still illuminates while driv- ing after adjusting the tire pressure, a tire may be flat. If you have a flat tire, replace it with a spare tire as soon as possible.
WARNING
If the light does not illuminate with the ignition switch pushed ON, have the vehicle checked by a NISSAN dealer as soon as possible.
If the light illuminates while driving, avoid sudden steering maneuvers or
. When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approxi- mately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/ or system resetting.
[ Edit: 2011/ 10/ 27 Model: E52-D ]
. Replacing tires with those not ori- ginally specified by NISSAN could affect the proper operation of the TPMS.
CAUTION
The TPMS is not a substitute for the regular tire pressure check. Be sure to check the tire pressure regularly.
If the vehicle is being driven at
speeds of less than 16 MPH (25
km/h), the TPMS may not operate
correctly.
. Be sure to correctly install
the specified size of tires to the four wheels.
Master warning light
GUID-AE6F59CE-42B9-444F-B156-919C688575F5
When the ignition switch is in the ON position,
the master warning light illuminates if any of the
following are displayed on the dot matrix liquid
crystal display:
. No key warning
Low fuel warning
Black plate (93,1)
Low washer fluid warning
. Parking brake release warning . Door/lift gate open warning . Check tire pressure warning See “Dot matrix liquid crystal display” (P.2-18).
Loose fuel cap warning
Seat belt warning light and chime
GUID-A109F64D-D61F-4A96-AD87-98431E7D57E1
The light and chime remind you to fasten seat
belts. The light illuminates whenever the ignition
switch is pushed to the ON position, and will
remain illuminated until the driver’s seat belt is
fastened. At the same time, the chime will sound
for approximately 6 seconds unless the driver’s
seat belt is securely fastened.
the front
The seat belt warning light
illuminate if the seat belt is not
passenger will
fastened when the front passenger’s seat
is
occupied. For approximately 5 seconds after the
ignition switch is in the ON position, the system
does not activate the warning light for the front
passenger.
See “Seat belts” (P.1-16) for precautions on
seat belt usage.
for
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Supplemental air bag warning light
GUID-053868B0-D825-4DAD-80BD-8335FF04C712
After pushing the ignition switch to the ON
position, the supplemental air bag warning light
will illuminate. The supplemental air bag warning
light will turn off after about 7 seconds if the
supplemental
front air bag and supplemental
side air bag, curtain side-impact air bag systems
and/or pretensioner seat belt are operational.
If any of the following conditions occur, the front
air bag, side air bag, curtain air bag and
pretensioner systems needs servicing and your
vehicle must be taken to your nearest NISSAN
dealer.
The supplemental air bag warning light remains on after approximately 7 seconds. The supplemental air bag warning light flashes intermittently. The supplemental air bag warning light does not come on at all.
Unless checked and repaired, the Supplemental Restraint Systems (air bag systems) and/or the pretensioners may not function properly. For additional restraint system” (P.1-47).
information, see “Supplemental
Instruments and controls 2-15
Black plate (94,1)
Exterior light indicator
or
GUID-DF342439-0FE3-4496-9A16-C533B45E0A28
This indicator illuminates when the headlight
switch is turned to the AUTO (if so equipped),
position and the front side marker
lights, the front parking lights, instrument panel
lights, tail lights, rear side marker lights, license
plate lights or headlights are on. The indicator
turns off when these lights are turned off.
Front passenger air bag status light
GUID-367FC65F-F709-47F5-B2C8-55C6BB057E93
The front passenger air bag status light (
will be lit and the passenger front air bag will be
OFF depending on how the front passenger
seat is being used.
For front passenger air bag status light opera-
tion, see “NISSAN advanced air bag system
(front seats)” (P.1-53) of this manual.
High beam indicator light
GUID-615CDEB6-E7A5-47B7-A115-94D5A95A46BC This light comes on when the headlight high beam is on and goes out when the low beam is selected.
30). INDICATOR LIGHTS
GUID-74D81D00-89E2-45CA-8D90-62256806AA00
Continuously Variable Transmis-
sion (CVT) position indicator light
GUID-EA4324B0-97BD-4543-B6F9-6455691DD2E7
When the ignition switch is pushed to the ON
position,
the indicator shows the automatic
selector shift position. (See “Continuously Vari-
able Transmission (CVT)” (P.5-12).)
Cruise indicator light
GUID-DDE42649-20AF-4630-87BB-B2941A1E1FEE
Cruise main switch indicator:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
This light illuminates when the cruise control
main switch is pushed. The light turns off when
the main switch is pushed again. When the
cruise main switch indicator light illuminates, the
cruise control system is operational.
(See
“Cruise control” (P.5-24).)
the cruise indicator
Cruise malfunction:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
light blinks while the
If
engine is running,
it may indicate the cruise
control system is not functioning properly. Have
the system checked by a NISSAN dealer. (See
“Cruise control” (P.5-24).)
WARNING
If the supplemental air bag warning light is on, it could mean that the front air bag, side air bag, curtain air bag and/or pretensioner systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible.
Vehicle Dynamic Control (VDC)
warning light
GUID-AE9CC0E0-4545-43E8-B644-9AA218EEAC08
The light will blink when the Vehicle Dynamic
Control (VDC) system or the traction control
system is operating, thus alerting the driver that
the vehicle is nearing its traction limits. The road
surface may be slippery.
If the VDC warning light comes on and stays on
while the VDC system is on, this light alerts the
driver to the fact that the VDC system’s fail-safe
mode is operating, for example the VDC system
may not be functioning properly. Have the
If a
system checked by a NISSAN dealer.
malfunction occurs in the system,
the VDC
system function will be canceled but the vehicle
is still driveable. For additional information, see
“Vehicle Dynamic Control (VDC) system” (P.5-
2-16 Instruments and controls
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Malfunction Indicator Light (MIL)
the malfunction indicator
GUID-1C68E634-2F16-4A6B-85E1-536C36C54FC0
If
light comes on
steady or blinks while the engine is running, it
may indicate a potential emission control mal-
function.
The malfunction indicator light may also come on
steady if the fuel-filler cap is loose or missing, or
if the vehicle runs out of fuel. Check to make
sure the fuel-filler cap is installed and closed
tightly, and that the vehicle has at least 3 US
gallons (11.4 liters) of fuel in the fuel tank.
After a few driving trips, the
light should
turn off if no other potential emission control
system malfunction exists.
If this indicator light remains on for 20 seconds
and then blinks for 10 seconds when the engine
is not running, it indicates that the vehicle is not
ready for an emission control system inspection/
maintenance test. (See “Readiness for inspec-
tion/maintenance (I/M) test” (P.9-27).)
Operation:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The malfunction indicator light will come on in
one of two ways:
. Malfunction indicator light on steady — An
emission control system has been detected.
Check the fuel-filler cap if the LOOSE FUEL
CAP warning appears on the dot matrix
liquid crystal display. If the fuel-filler cap is
Black plate (95,1)
loose or missing, tighten or install the cap and continue to drive the vehicle. The light should turn off after a few driving trips. If the light does not turn off after a few driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.
. Malfunction indicator light blinking — An engine misfire has been detected which may damage the emission control system. To reduce or avoid emission control system damage:
a)
b) c) d)
Do not drive at speeds above 45 MPH (72
km/h).
Avoid hard acceleration or deceleration.
Avoid steep uphill grades.
If possible, reduce the amount of cargo being
hauled or towed.
light may stop
The malfunction indicator blinking and remain on. Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.
CAUTION
Continued vehicle operation without having the emission control system and repaired as necessary could lead
to poor driveability, reduced fuel econ- omy, and possible damage to the emis- sion control system.
Overdrive off indicator light
GUID-B248403A-7160-4641-9641-C1D42F7AEF5D The overdrive off indicator light illuminates when the overdrive off mode is selected. For additional information, see “Continuously Variable Transmission (CVT)” (P.5-12) of this manual.
Security indicator light
GUID-ECFD3652-2277-449D-95FC-FDE76A31BDDE The light blinks when the ignition switch is in the ACC, OFF or LOCK position. This function indicates the security system equipped on the vehicle is operational. If the security system is malfunctioning, this light will remain on while the ignition switch is in the ON position. For additional information, see “Security systems” (P.2-27).
Turn signal/hazard indicator lights GUID-DEC39268-26DF-4838-A9EA-6A903EF57EBB The light flashes when the turn signal switch lever or hazard switch is turned on.
Instruments and controls 2-17
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Parking brake reminder chime
GUID-B170CCAE-51B0-4C2A-93DA-57D00974E4A8
The chime will sound if the vehicle is driven at
more than 4 MPH (7 km/h) with the parking
brake applied. Stop the vehicle and release the
parking brake.
Brake pad wear warning
GUID-11093B54-7D84-4D73-B07E-6FB94DF62F91
The disc brake pads have audible wear warn-
ings. When a brake pad requires replacement, it
will make a high pitched scraping sound when
the vehicle is in motion. This scraping sound will
first occur only when the brake pedal
is
depressed. After more wear of the brake pad,
the sound will always be heard even if the brake
pedal
is not depressed. Have the brakes
checked as soon as possible if the warning
sound is heard.
Black plate (96,1)
DOT MATRIX LIQUID CRYSTAL DISPLAY
GUID-DF977CB1-DA21-4D82-92AC-EC347BF184E2
JVI0254X
The dot matrix liquid crystal display *1
is
located in the speedometer, and it displays,
the key operation information and other warn-
ings and information.
For the detail about the Intelligent Key system,
see “Intelligent Key system” (P.3-13).
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Vehicle Dynamic Control (VDC) off
indicator light
GUID-36C6A5CB-7D96-42B6-B569-12EA0CD78A19
The light comes on when the vehicle dynamic
control off switch is pushed to OFF. This
indicates that
the vehicle dynamic control
system and traction control system are not
operating.
AUDIBLE REMINDERS
GUID-5CBEA2B2-B021-4887-B30F-E3C585323EDD
Key reminder chime
GUID-2453E6AA-C9B7-4D05-8394-0F1BB506FF53
A chime will sound if the driver side door is
opened while the ignition switch is pushed to
the ACC position. Make sure the ignition switch
is pushed to the OFF position, and take the
Intelligent Key with you when leaving the vehicle.
Light reminder chime
GUID-BFB5E744-D2B8-408B-834A-688BCF472327
A chime will sound when the driver side door is
opened with the light switch in the
or
position and the ignition switch in the ACC
or OFF position. Turn the light switch off when you leave the vehicle. Models with Autolight system: The chime will also sound for 2 seconds when the ignition switch is turned to the OFF position with the fog lights on while the headlight switch is in the AUTO position.
2-18 Instruments and controls
Black plate (97,1)
SIC4716
Instruments and controls 2-19
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (98,1)
3. SHIFT “P” warning
GUID-39C72E43-25FF-4A4F-B9A5-6B99999E8518
This warning appears when the ignition switch is
pushed to stop the engine with the selector lever
in any position except the P (Park) position.
If this warning appears, move the selector lever
to the P (Park) position or push the ignition
switch to the ON position.
An inside warning chime will also sound. (See
“Intelligent Key system” (P.3-13).)
4. “PUSH” warning GUID-8B1B73E4-768D-4801-A346-AFE043207C1E This warning appears when the selector lever is moved to the P (Park) position with the ignition switch in the ACC position after the SHIFT “P” warning appears. To push the ignition switch to the OFF position, perform the following procedure: SHIFT “P” warning ? (Move the selector lever to “P”) ? PUSH warning ? (Push the ignition switch ? ignition switch position is turned to ON) ? PUSH warning ? (Push the ignition switch ? ignition switch position is turned to OFF)
5. Key battery discharge indicator GUID-967F63CE-1C05-4DC3-99FB-8F1F04EBE95F This indicator appears when the key battery is running out of power. If this indicator appears, replace the battery with a new one. (See “Intelligent Key battery replace- ment” (P.8-22).)
6. Engine start operation for Intelligent Key system indicator GUID-0A04A4BE-EA21-48A0-88E9-6C87C0E9DC4D This indicator appears when the Intelligent Key battery is running out of power and when the Intelligent Key System and vehicle are not communicating normally. If touch the ignition switch with the Intelligent Key while depressing the brake pedal. (See “Intelligent Key battery discharge” (P.5-11).)
this indicator appears,
7. Parking brake release warning
GUID-029C1509-C86D-41F0-AE2B-6B98338F1BE8
This warning appears when the vehicle speed is
above 4 MPH (7 km/h) and the parking brake is
applied. Stop the vehicle and release the
parking brake.
OPERATIONAL INDICATORS
GUID-AD5B0BAF-2C91-4EC9-A709-EB982E1C0773
1. Engine start operation indicator GUID-3A8E6F2E-0AEB-4F35-B6FE-0018789257BC This indicator appears when the selector lever is in the P (Park) position. This indicator means that the engine will start by pushing the ignition switch with the brake pedal depressed. You can start the engine directly in any position.
2. NO KEY warning GUID-75410B7B-4F58-4067-BDFB-93074F70EDAC This warning appears in either of the following conditions.
No key inside the vehicle:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The warning appears when the door is closed
with the Intelligent Key left outside the vehicle
and the ignition switch in the ACC or ON
position. Make sure that the Intelligent Key is
inside the vehicle.
Unregistered key:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The warning appears when the ignition switch is
pushed from the LOCK position and the key
cannot be recognized by the system. You cannot
start the engine with an unregistered key. Use
the registered key.
See “Intelligent Key system” (P.3-13) for more
details.
2-20 Instruments and controls
[ Edit: 2011/ 10/ 27 Model: E52-D ]
8. Low fuel warning GUID-3F6A4C14-3A53-4889-81A1-9712B64C7CFB This warning appears when the fuel level in the tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches the empty (0) position. There is a small reserve of fuel remaining in the tank when the fuel gauge reaches the empty (0) position.
9. Low washer fluid warning
GUID-56C625DC-ABE9-4A02-8BC9-E75B59CC1B40
This warning appears when the washer tank fluid
is at a low level. Add washer fluid as necessary.
(See “Window washer fluid” (P.8-13).)
10. Door/lift gate open warning (ignition switch is in the ON position) GUID-369BA1E4-345B-4EDC-949F-A60010E2FCAE This warning appears if any of the doors and/or the lift gate are open or not closed securely. The vehicle icon indicates which door is open on the display.
11. Loose fuel cap warning
GUID-AE37C079-2D1D-4EC5-BC3E-A6F3746AC355
This warning appears when the fuel-filler cap is
not
tightened correctly after the vehicle has
been refueled. (See “Fuel-filler cap” (P.3-30).)
12. Check tire pressure warning
GUID-DA5B077D-A7AE-4C80-ABBC-FC03EE16A559
This warning appears when the low tire pressure
warning light in the meter illuminates and low tire
pressure is detected.
If this warning appears,
stop the vehicle and adjust the tire pressure to
the recommended COLD tire pressure shown
on the Tire and Loading Information label. (See
“Low tire pressure warning light” (P.2-14) and
“Tire Pressure Monitoring System (TPMS)” (P.5-
3).)
13. “TIMER” indicator
GUID-1125717D-01A2-4EE0-BD94-FCEC2E95C1E9
This indicator appears when the set “timer”
indicator activates. You can set the time for up to
6 hours. (See “Trip computer” (P.2-22).)
14. Low outside temperature warning
GUID-05A3065E-96A4-4FAF-9E94-F0DF064F6767
This warning appears if the outside temperature
is below 378F (38C). The warning can be set not
to be displayed. (See “Trip computer” (P.2-22).)
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (99,1)
SIC4237
Instruments and controls 2-21
Black plate (100,1)
SIC3580
switch switch
TRIP COMPUTER
GUID-930DEE09-4374-4996-AC0B-1BBE0A7E2A37
Switches for the trip computer are located on
the right side of the combination meter panel. To
operate the trip computer, push the side of the
switches as shown above.
*A
*B
When the ignition switch is pushed to the ON
position, modes of the trip computer can be
selected by pushing the
switch *A
Each time the
display will change as follows:
Current and average fuel consumption ?
Average fuel consumption and speed ?
switch *A .
is pushed, the
replacement indicator for a certain driving distance does not mean your tires will last that long. Use the tire replacement indicator as a guide only and always perform regular tire checks. Failure to perform regular tire checks, including tire pressure checks could result in tire failure. Serious vehicle damage could occur and may lead to a collision, which could result in serious personal injury or death.
4. “OTHER” indicator
GUID-3F118BD8-4E3B-4C42-83AA-190A2A80C162
This indicator appears when the set time comes
for replacing items other than the engine oil, oil
filter and tires. You can set or reset the distance
for replacing the items. (See “Trip computer”
(P.2-22).)
Models with center multi-function control panel:
More maintenance reminders are also available
on the center display. (models with center multi-
function control panel) (See “How to use INFO
button” (P.4-10).)
MAINTENANCE INDICATORS
GUID-FA009BEE-2E37-4E85-BAC3-65B2871DE287
1. Engine oil replacement indicator
GUID-B49EC615-22D1-4111-845C-214CE38146A9
This indicator appears when the customer set
time comes for changing the engine oil. You can
set or reset the distance for changing the engine
oil. (See “Trip computer” (P.2-22).)
2. Oil filter replacement indicator GUID-8EC15863-1C70-4332-BAFA-4C2E8EE6FBFC This indicator appears when the customer set time comes for replacing the oil filter. You can set or reset the distance for replacing the oil filter. (See “Trip computer” (P.2-22).)
3. Tire replacement indicator GUID-83F3C488-F446-4361-92F6-CBED0996F98C This indicator appears when the customer set distance comes for replacing tires. You can set or reset the distance for replacing tires. (See “Trip computer” (P.2-22).)
WARNING
The tire replacement indicator is not a substitute for regular tire checks, in- cluding tire pressure checks. See “Changing wheels and tires” (P.8-35). Many factors including tire inflation, alignment, driving habits and road con- ditions affect tire wear and when tires should be replaced. Setting the tire
2-22 Instruments and controls
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (101,1)
Elapsed time and trip odometer ? Distance to empty (dte) ? Outside air temperature (ICY) ? Setting ? Warning check
SIC4700
SIC3674
Current and average fuel consumption
(MPG, l (liter)/100 km or km/l)
GUID-F605A791-7C05-4ACC-98CA-7D5109816B91
The current and average fuel consumption mode
shows the current and average fuel consump-
tion.
Average fuel consumption (MPG, l/100
km or km/l) and speed (MPH or km/h)
GUID-E1893F46-D3FE-4C74-B5F8-C57C75093BC1
Fuel consumption:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The average fuel consumption mode shows the
average fuel consumption since the last reset.
switch *B
Resetting is done by pushing the
for longer than 1 second. (The average speed is
also reset at the same time.)
The display is updated every 30 seconds. At
about the first 1/3 mile (500 m) after a reset, the
display shows “——”.
Speed:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The average speed mode shows the average
vehicle speed since the last reset. Resetting is
Instruments and controls 2-23
[ Edit: 2011/ 10/ 27 Model: E52-D ]
switch *B for longer done by pushing the than 1 second. (The average fuel consumption is also reset at the same time.) The display is updated every 30 seconds. The first 30 seconds after a reset, the display shows “——”.
Black plate (102,1)
SIC4701
SIC4702
Elapsed time and trip odometer (miles or km)
GUID-5904C9FC-EFD8-4B9B-97AD-8438716FCDA6
Elapsed time:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The elapsed time mode shows the time since
the last reset. The displayed time can be reset
switch *B for longer than 1
by pushing the
second. (The trip odometer is also reset at the
same time.)
Trip odometer:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The trip odometer mode shows the total
distance the vehicle has been driven since the
last reset. Resetting is done by pushing the
switch *B
than 1 second.
elapsed time is also reset at the same time.)
longer
(The
for
Distance to empty (dte — miles or km)
GUID-463716F9-529A-4489-8DA6-E69543606427
The distance to empty (dte) mode provides you
with an estimation of the distance that can be
driven before refueling. The dte is constantly
being calculated, based on the amount of fuel in
the fuel tank and the actual fuel consumption.
The display is updated every 30 seconds.
The dte mode includes a low range warning
feature.
level
is low, the warning is
displayed on the screen.
When the fuel
display will change to “——”.
If the amount of fuel added is small, the display just before the ignition switch is
level drops even lower, the dte
If the fuel
2-24 Instruments and controls
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (103,1)
pushed to the OFF position may continue to be displayed.
. When driving uphill or rounding curves, the fuel in the tank shifts, which may momenta- rily change the display.
SIC4703
SIC3678
Outside air temperature (ICY — 8F or 8C)
GUID-7BA169AD-2C22-4452-AB3D-9412E817F174
The outside air temperature is displayed in 8F or
8C in the range of −22 to 1408F (−30 to 608C).
The outside air temperature mode includes a low
temperature warning feature.
If the outside air
temperature is below 378F (38C), the warning is
displayed on the screen.
The outside temperature sensor is located in
front of the radiator. The sensor may be affected
by road or engine heat, wind directions and
other driving conditions. The display may differ
from the actual outside temperature or
the
temperature displayed on various signs or bill-
boards.
Setting
GUID-81BEB78D-5B29-43BA-9378-A6E18A1FD1E5
Setting cannot be made while driving. A
message “Setting can only be operated
when stopped” is also displayed on the dot
matrix crystal display.
switch *B are
switch *A and
The
used in the setting mode to select and decide a
menu.
SKIP: Push the check mode. Push the
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
switch *A to move to the warning
switch *B to select other menus.
Instruments and controls 2-25
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (104,1)
To return to the top page of the setting mode, select “BACK”.
ALERT:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
Alert menu can be set to notify the following
items.
TIMER Select this submenu to specify when the “TIMER” indicator activates. ICY Select outside temperature warning.
this submenu to display the low
To return to the top page of the setting mode, select “BACK”.
MAINTENANCE:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
The maintenance intervals of the following items
can be set or reset for the reminders.
. OIL
this submenu to set or reset
this submenu to set or reset
Select distance for changing the engine oil. FILTER Select distance for replacing the oil filter. TIRE Select distance for replacing tires.
this submenu to set or reset
the
the
the
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
to your
OPTIONS: The 3 option menus can be set preference.
LANGUAGE Select French or Spanish for display.
this submenu to choose English,
. UNIT
Select this submenu to choose the unit.
. EFFECTS
the effects de-
Select this menu to set scribed below to on or off. — The indicator needles sweep in the meters and the ring illumination will be brightened gradually when the engine is started.
To return to the top page of the setting mode, select “BACK”.
. OTHER
Select this submenu and set or reset the distance for replacing items other than the engine oil, oil filter and tires.
2-26 Instruments and controls
[ Edit: 2011/ 10/ 27 Model: E52-D ]
SIC3993
Warning check
GUID-5790185F-3109-4184-B244-017BA03FF1E8
To see if there are any of the following warnings
and corresponding details, select this menu.
. No key warning
. Parking brake release warning
. Door/lift gate open warning
. Check tire pressure warning
Low fuel warning Low washer fluid warning
Loose fuel cap warning
SKIP: Push the check mode.
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
switch *A to move to the warning
SECURITY SYSTEMS
GUID-1DA67D67-9764-4420-8B43-5CA25C056F36
Push the
switch *B to select other menus.
DETAIL:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
This item is available only when a warning is
displayed.
Select this menu to see the details of warnings.
SIC4717
Your vehicle has two types of security systems, as follows: . Vehicle security system . NISSAN Vehicle Immobilizer System The security condition will be shown by the security indicator light.
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Black plate (105,1)
VEHICLE SECURITY SYSTEM
GUID-A4B1DF8A-E0E9-47D0-B1DC-2F43B0CC0B71
The vehicle security system provides visual and
audio alarm signals if someone opens the doors
or lift gate when the system is armed. It is not,
however, a motion detection type system that
activates when a vehicle is moved or when a
vibration occurs.
The system helps deter vehicle theft but cannot
prevent it, nor can it prevent the theft of interior
or exterior vehicle components in all situations.
Always secure your vehicle even if parking for a
brief period. Never leave your Intelligent Key(s)
in the vehicle, and always lock it when un-
attended. Be aware of your surroundings, and
park in secure, well-lit areas whenever possible.
Many devices offering additional protection,
such as component locks, identification markers,
and tracking systems, are available at auto
supply stores and specialty shops. Your
NISSAN dealer may also offer such equipment.
Check with your insurance company to see if
you may be eligible for discounts for various
theft protection features.
Instruments and controls 2-27
Black plate (106,1)
by releasing the door inside lock knob, the alarm will activate.)
How to stop an activated alarm GUID-05DDA89B-F7D9-4C65-A192-A1CBC7D96A4F The alarm will stop by unlocking a door by pushing the unlock button on the Intelligent Key, the door handle request switch or using the mechanical key. The alarm will not stop if the ignition switch is pushed to the ACC or ON position. If the system does not operate as de- scribed above, have it checked by a NISSAN dealer. NISSAN VEHICLE IMMOBILIZER SYS- TEM GUID-3F81F329-63EA-4A18-A472-E8D6E2A9B23A The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered Intelligent Key. Never leave these keys in the vehicle.
For USA:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
about 30 seconds the vehicle security system automatically shifts into the armed phase. The security light begins to flash once every approximately 3 seconds. If, during this 30-second pre-arm time period, the door is unlocked, or the ignition switch is pushed to ACC or ON, the system will not arm.
Even when the driver and/or passengers are in the vehicle, the system will activate with all doors and lift gate locked with the ignition switch in the LOCK position. When pushing the ignition switch to the ACC or ON position, the system will be released.
Vehicle security system activation GUID-BB38DE0B-6ADD-44EA-821D-7DC2AE8F4E1E The vehicle security system will give the follow- ing alarm:
The headlights blink and the horn sounds intermittently. The alarm automatically turns off after approximately 1 minute. However, the alarm reactivates if the vehicle is tampered with again.
The alarm is activated by: . Unlocking the door or opening the lift gate without using the button on the Intelligent Key, the door handle request switch or the mechanical key. (Even if the door is opened
[ Edit: 2011/ 10/ 27 Model: E52-D ]
SIC2045
How to arm the vehicle security system 1. Close all windows.
GUID-8D123C36-E9F9-4871-811D-D6C0C142AF46
The system can be armed even if the windows are open.
2. Push the ignition switch to the OFF position. 3. Remove the Intelligent Key from the vehicle. 4. Close all doors and lift gate. Lock all doors. The doors can be locked with the Intelligent Key, door handle request switch, power door lock switch or mechanical key.
5. Confirm that
the security indicator
light comes on. The security indicator light stays on for about 30 seconds. The vehicle security system is now pre-armed. After
2-28 Instruments and controls
Black plate (107,1)
service as soon as possible. Please bring all Intelligent Keys that you have when visiting a NISSAN dealer for service.
Note: Changes or modifications not ex- pressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For Canada:
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device.
SIC2045
It
indicates the status of
Security indicator light GUID-25A364CB-C81A-4EA9-91A8-8EC3F1236ADD The security indicator light is located on the meter panel. the NISSAN Vehicle Immobilizer System. The light blinks after the ignition switch is in the LOCK, ACC or OFF position. This function indicates the security systems equipped on the vehicle are operational. If the NISSAN Vehicle Immobilizer System is malfunctioning, this light will remain on while the ignition switch is in the ON position. If the light still remains on and/or the engine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Instruments and controls 2-29
Black plate (108,1)
reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate and water.
WINDSHIELD WIPER AND WASHER SWITCH
GUID-FDCAE580-2A84-4682-B1FD-320CE21EDECE
WARNING
In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield.
CAUTION
. Do not operate the washer continu-
ously for more than 30 seconds.
. Do not operate the washer if the
reservoir tank is empty.
. Do not
fill
the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.
. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer
2-30 Instruments and controls
[ Edit: 2011/ 10/ 27 Model: E52-D ]
SIC3664
The windshield wiper and washer operates
when the ignition switch is in the ON position.
Push the lever down to operate the wiper at the
following speed:
*1
INT — intermittent operation can be adjusted by turning the knob toward *A (Slower) or *B (Faster). Models with center multi-function control panel: When the speed sensing wiper interval function is turned on, the intermittent operation speed varies in accordance with the vehicle speed. (For example, when the vehicle speed is high, the intermittent operation speed will be faster.) Note that the function is set to disabled as the factory default setting. To turn this function on and off, see “How to use SETTING button” (P.4-
14). LO — continuous low speed operation HI — continuous high speed operation
*2
*3
Push the lever up *4
operation of the wiper.
Pull the lever toward you *5
to operate the
washer. Then the wiper will also operate several
times.
(MIST) to have one sweep
Black plate (109,1)
window washer reservoir tank to mix the washer fluid concentrate and water.
If the rear window wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approxi- mately 1 minute, turn the switch on again to operate the wiper.
REAR WINDOW WIPER AND WASHER SWITCH
GUID-4EFE8824-F7D6-4B77-8C35-4B178AEF16FE
WARNING
In freezing temperatures the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window.
CAUTION
. Do not operate the washer continu-
ously for more than 30 seconds.
. Do not operate the washer if the
reservoir tank is empty.
. Do not
fill
the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.
. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the
[ Edit: 2011/ 10/ 27 Model: E52-D ]
Instruments and controls 2-31
Black plate (110,1)
REAR WINDOW AND OUTSIDE MIRROR DEFROSTER SWITCH
HEADLIGHT AND TURN SIGNAL SWITCH
GUID-68222C06-7E77-4CA2-9366-C9EF650F0773
SIC3666
SIC4718
The rear window wiper and washer operate
when the ignition switch is in the ON position.
Turn the switch clockwise from the OFF position
to operate the wiper.
*1
*2
Push the switch forward *3
to operate the
washer. Then the wiper will also operate several
times.
Intermittent (INT) — intermittent operation (not adjustable) Low (ON) — continuous low speed operation
To defog/defrost
the rear window glass and
outside mirrors (if so equipped), start the engine
and push the switch *1 on. The indicator light
*2 will come on. Push the switch again to turn
the defroster off.
It will automatically turn off in approximately 15
minutes.
CAUTION
When cleaning the inner side of the rear window, be careful not to scratch or damage the rear window defroster.
2-32 Instruments and controls
[ Edit: 2011/ 10/ 27 Model: E52-D ]
XENON HEADLIGHTS (if so equipped)
GUID-CC0390FD-A90C-4063-BD6B-CECF22FC578F
GUID-D9DAF618-DD19-4AB8-A7E7-0771E1807CBF
WARNING
HIGH VOLTAGE
. When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at a NISSAN dealer.
. Xenon headlights provide consider- ably more light than conventional headlights. If they are not correctly aimed, they might temporarily blind an oncoming driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your ve- hicle to a NISSAN dealer and have the headlights adjusted correctly.
When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize.
The life of xenon headlights will be shortened by frequent on-off opera- tion. It is generally desirable not to turn
.
off the headlights for short intervals (for example, when the vehicle stops at a traffic signal). This way the life of the xenon headlights is not reduced. If the xenon headlight bulb is close to burning out, the brightness will drasti- cally decrease, the light will start blinking, or the color of the light will become reddish. If one or more of the above signs appear, contact a NISSAN dealer.
Black plate (111,1)
SIC3668
SIC3669
HEADLIGHT SWITCH
GUID-A43F6381-338B-4EC9-A32F-C8BB85E70D22
Lighting
*1
*2
GUID-6168B903-3FE2-4D4D-A6B4-8FA2B2AB4E64
position: