Download PDF Manual


c When the


position is selected, the air conditioner automatically turns on (however, the indicator light will not illu- minate). This dehumidifies the air which helps defog the windshield. The air recir- culation mode automatically turns off, allowing outside air to be drawn into the passenger compartment which helps de- fog the windshield.


Bi-level heating/cooling This mode directs air from the side, center and foot outlets. 1. Push the 2. Push the 3. Move the fan control dial to the desired


button to the off position. button in.


position.


4. Move the temperature control lever to the


desired position.


Heating and defogging This mode heats the interior and defogs the windshield. 1. Push the 2. Move the fan control dial to the desired


button in.


position.


3. Move the temperature control lever to the desired position between the middle and the HOT position.


Operating tips c Clear snow and ice from the wiper blades and air inlet in front of the windshield. This improves heater op- eration.


c When the


or


switch is selected, the air recirculation mode automatically turns off. Outside air is drawn into the passenger compartment to improve the defogging performance.


AIR CONDITIONER OPERATION (if so equipped) Start the engine, move the fan control dial to the desired (1 to 4) position and push in the A/C button to activate the air conditioner.


When the air conditioner is on, cooling and dehumidifying functions are added to the heater operation. The air conditioner cooling function op- erates only when the engine is running. Cooling This mode is used to cool and dehumidify the air. 1. Push the 2. Push the 3. Move the fan control dial to the desired


button to the off position. button in.


position.


4. Push on the air conditioner button. The


indicator light comes on.


5. Move the temperature control lever to the


desired position.


c For quick cooling when the outside tem- perature is high, push the button to the on position (Indicator light on). Be sure to return the button to the off position for normal cooling.


Dehumidified heating This mode is used to heat and dehumidify. 1. Push the button to the off position. Heater, air conditioner and audio systems 4-5


Z X


and QUICK heating, cooling, or defrosting.


2. Push the 3. Move the fan control dial to the desired


button in.


position.


4. Push on the air conditioner button. The


indicator light comes on.


5. Move the temperature control lever to the


desired position.


button in.


Dehumidified defogging This mode defogs the windows and dehu- midifies the air. 1. Push the When the position is selected, the air conditioner automatically turns on (however, the indicator light will not illu- minate). This dehumidifies the air which helps defog the windshield. The air recir- culation mode automatically turns off, allowing outside air to be drawn into the passenger compartment which helps de- fog the windshield.


2. Move the fan control dial to the desired


position.


3. Move the temperature control lever to the


desired position.


Outside air is drawn into the passenger compartment to improve the defogging per- formance. Operating tips c Keep the windows and sun roof closed while the air conditioner is in operation. c After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This allows the air conditioner to cool the interior more quickly.


c The air conditioner system should be operated for approximately ten min- utes at least once a month. This helps prevent damage to the system due to lack of lubrication.


c If the engine coolant temperature gauge exceeds the H (hot) position, turn the air conditioner off. See ‘‘If your vehicle over- heats’’ in the ‘‘In case of emergency’’ section of this owner’s manual for addi- tional information.


AIR FLOW CHARTS The charts on the following pages show the switch and lever positions for MAXIMUM


4-6 Heater, air conditioner and audio systems


Z X


WHA0017


WHA0018


Heater, air conditioner and audio systems 4-7


Z X


4-8 Heater, air conditioner and audio systems


WHA0021


WHA0019


Z X


SERVICING AIR CONDITIONER


The air conditioner system in your NISSAN vehicle is charged with a refrigerant de- signed with the environment in mind. This refrigerant does not harm the earth’s ozone layer. Special charging equipment and lubricant is required when servicing your NISSAN air conditioner. Using improper refrigerants or lubricants will cause severe damage to your air conditioner system. See ‘‘Air conditioner system refrigerant and lubricant recommen- dations’’ in the ‘‘Technical and consumer information’’ section of this manual. Your NISSAN dealer is able to service your environmentally ‘‘friendly’’ air conditioning system.


WARNING


The air conditioner system contains refrigerant under high pressure. To avoid personal injury, any air condi- tioner service should be done only by an experienced technician with proper equipment.


WHA0020


Heater, air conditioner and audio systems 4-9


Z X


AUDIO SYSTEM


LHA0002


influences.


FM-AM RADIO WITH COMPACT DISC (CD) PLAYER Audio main operation To turn the radio on, turn the ignition key to ACC or ON. If you listen to the radio with the engine not running, turn the key to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the vehicle may influence radio reception quality. Power/Volume control Turn the ignition key to ACC or ON, then push the power/volume control knob. The mode (radio or CD) which was playing im- mediately before the system was turned off resumes playing. When no CD is loaded, the the power/volume control knob again turns the system off.


on. Pushing


comes


radio


4-10 Heater, air conditioner and audio systems


Z X


will reappear. Once the sound quality is set knob to the desired level, press the repeatedly until the radio or CD display reappears.


Turn the power/volume control knob to the right to increase volume or to the left to decrease volume. Adjusting tone quality and speaker bal- ance To adjust Bass, Treble, Fader or Balance, press the knob for less than 1.5 sec- onds. A beep signals entry into the audio adjustment mode and BASS will appear in knob to adjust the display. Rotate the Bass (BASS) to the desired level. Press the knob a second time and TREB appears in the display. Rotate the knob to adjust Treble (TREB) to the


desired level. knob a third time and FAD Press the appears in the display. Fader (FAD) adjusts the sound between the front and rear speaker. Rotate the knob to adjust Fader (FAD) to the desired level. Press the knob a fourth time and BAL appears in the display. Balance (BAL) ad- justs the sound between the right and left speakers. Rotate the knob to adjust Balance (BAL) to the desired level. After 10 seconds, the radio or CD display


Heater, air conditioner and audio systems 4-11


Z X


Clock operation The clock is on in the display regardless of what mode, media, or function the radio is in as long as the ignition is in ACC or ON. Clock set To adjust the clock, press the knob for longer than 1.5 seconds. A beep signals entry into the clock adjustment mode and CL appears in the display. The hours will be knob to adjust blinking. Rotate the the hours to the desired level. Press the knob a second time and the minutes will start to blink. Rotate the the minutes to the


knob to adjust


desired level. After 10 seconds, the radio or CD display will reappear. Once the clock is set to the knob repeat- desired level, press the edly until the radio or CD display reappears.


Z X


4-12 Heater, air conditioner and audio systems


LHA0025


Knob


WARNING


The radio should not be tuned while driving so full attention may be given to vehicle operation.


Rotate the left for manual tuning.


knob to the right or to the


SEEK/SCAN tuning


SEEK tuning Push the SEEK/SCAN tuning button


or for less than 1.5 seconds. SEEK tuning begins from high to low frequencies or low to high frequencies, depending on which but- ton is pressed, and stops at the next broad- casting station. Once the highest broadcast- ing station is reached, the radio continues in the SEEK mode at the lowest broadcasting station. If using the button, once the lowest broadcasting station is reached, the radio continues in the SEEK mode at the highest broadcasting station.


FM/AM radio operation FM/AM band select Push the band select button (FM/AM) to change from AM to FM1 to FM2 reception. The FM stereo indicator, ST, illuminates


LHA0026


during FM stereo reception. When the ste- reo broadcast signal the radio automatically changes from stereo to mon- aural reception.


is weak,


Heater, air conditioner and audio systems 4-13


Z X


SCAN tuning Push the SEEK/SCAN tuning button


or for more than 1.5 seconds. SCAN ap- pears in the display window. SCAN tuning begins from high to low frequencies or low to high frequencies, depending on which button is pressed. SCAN tuning stops at each broadcasting station for five seconds. Pushing the button again during this five second period stops SCAN tuning and the radio remains tuned to that station. Station memory operations Six stations can be set for the AM band. 12
stations can be set for the FM band (six for FM1, six for FM2). 1. Push band select button (FM/AM) to se- lect AM, FM1, or FM2. The selected band illuminates in the display.


2. Tune to the desired station. 3. Push the desired station select button for more than 1.5 seconds. The radio mutes when the select button is pushed.


4. When the indicator illuminates in the display and the sound resumes, memo- rizing is complete.


5. Other station select buttons can be set in


the same manner.


If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired stations. COMPACT DISC (CD) player op- eration Turn the ignition key to the ACC or ON position, and carefully insert the compact disc into the slot with the label side up. The compact disc is automatically pulled into the slot and starts to play. If the radio is already operating, it automati- cally turns off and the compact disc begins to play.


CAUTION


Do not force the compact disc into the slot. This could damage the player.


CD button When this button is pushed with the compact disc loaded and the radio playing, the radio turns off and the compact disc starts to play. When power/volume control knob is pushed


4-14 Heater, air conditioner and audio systems


while the compact disc is playing, the com- pact disc stops playing.


FF (Fast forward), REW (Rewind) or


When the button is pushed while the compact disc is playing, the com- pact disc plays at an increased speed while fast forwarding or rewinding. When the but- ton is released, the compact disc returns to normal play speed.


APS (Automatic Program Search) FF, APS REW


When the button is pushed while the compact disc is playing, the selection fol- lowing the present one starts to play from but- the beginning. Push or hold the ton several times to skip several selections. Each time the button is pushed, the CD advances one selection. (When the last selection on the compact disc is skipped, the first selection is played.) When the button is pushed, the selec- tion being played returns to the beginning. Push or hold the button several times to skip back several selections. Each


Z X


time the button is pushed, the CD moves back one selection.


RPT (Repeat)


When the repeat button is pushed while the compact disc is playing, the play pattern changes as follows. 1: The current selection is repeated. MIX: Selections are played at random, not following the sequence on the compact disc. The same program may be repeated twice. Normal (no symbol): All selections are played in sequence, and the compact disc stops when the last selection is finished. When a new compact disc is inserted, the play pattern automatically changes to the ‘‘Normal’’ play pattern.


CD EJECT


When the button is pushed with a com- pact disc loaded, the compact disc ejects. When the button is pushed while the compact disc is playing, the compact disc ejects and the system turns off. If the compact disc ejects and is not


removed within 10 seconds, it is pulled back into the slot. DISC indicator light CD IN appears on the display when a CD is loaded with the system ON.


LHA0049


CD care and cleaning c Handle a CD by its edges. Never touch the surface of the disc. Do not bend the disc.


c Always place the discs in the storage


case when they are not being used.


c To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion. Do not use a conventional record cleaner or alcohol intended for industrial use.


Heater, air conditioner and audio systems 4-15


Z X


c Recordable compact discs (CD-R) may not function properly in the CD player.


c A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer edges with the side of a pen or pencil as illustrated.


CAUTION


c During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely.


c The player may skip while driving on


rough roads.


c The CD player sometimes cannot function when the passenger com- partment temperature is extremely high. Decrease the temperature be- fore use.


c Do no expose the CD to direct sun-


light.


c Do not touch the playing surface of


the disc.


c Do not use 8cm discs. They may cause player damage even if using with the optional adapter.


4-16 Heater, air conditioner and audio systems


Z X


influences.


FM-AM RADIO WITH CASSETTE PLAYER AND COMPACT DISC (CD) PLAYER Audio main operation To turn the radio on, turn the ignition key to ACC or ON. If you listen to the radio with the engine not running, turn the key to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, buildings, bridges, mountains and other ex- ternal Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the vehicle may influence radio reception quality. ONzOFF/VOL control knob Turn the ignition key to ACC or ON, then push the ONzOFF/VOL control knob button. The mode (radio, tape or CD) which was playing immediately before the system was turned off resumes playing. When no CD or tape is loaded, the radio comes on. Pushing the ONzOFF/VOL control knob button again turns the system off.


WHA0001


Heater, air conditioner and audio systems 4-17


Z X


Turn the ONzOFF/VOL control knob to the right to increase volume or to the left to decrease volume. Adjusting tone quality and speaker bal- ance To adjust the audio levels for bass, treble, balance, and fader, push the audio button and adjust the level with the TUNE/DISC buttons. Press the audio button once for BAS (bass), twice for TRE (treble), three times for FAD (fader), and four times for BAL (balance). Once the audio level is set the display will return back to radio, cassette or CD display mode after 7 seconds or the audio button can be pressed again within 7 seconds to set the next audio level. Pressing the audio button a fifth time will also return the display back to radio, cassette or CD display mode. Fader adjusts the sound level between the front and rear speakers, balance adjusts the sound level between the right and left speakers.


4-18 Heater, air conditioner and audio systems


AHA1088


Z X


Clock operation Pressing the clock button alternates the clock and the radio/cassette/CD player op- tions in the display. Clock set buttons to- Depressing the clock and gether sets hours. Depressing the clock and


buttons together sets minutes.


Clock priority mode In this mode the clock is shown in the display. If any radio, cassette or CD func- tions are activated, the radio, cassette or CD display illuminates for 10 seconds then returns to the clock mode. NOTE: After clock adjustment, the radio is in the clock priority mode. FM/AM Radio operation FM/AM band select


button to change from AM to


Push the FM reception. The FM stereo indicator, ST, illuminates during FM stereo reception. When the ste- reo broadcast signal the radio


is weak,


SCAN tuning Push the SEEK/SCAN tuning button


or for more than 0.5 seconds. SCAN illu- minates in the display, and the radio station blinks. SCAN tuning begins from low to high frequencies or high to low frequencies, de- pending on which button is pressed. SCAN tuning stops at each broadcasting station for five seconds. During the SCAN function, SCAN comes on and the radio station blinks in the display window. Pushing the button again during this five second period stops SCAN tuning and the radio remains tuned to that station.


automatically changes from stereo to mon- aural reception.


TUNE/DISC


WARNING


The radio should not be tuned while driving so full attention may be given to vehicle operation.


and


Use the buttons for manual tuning. To move quickly through the chan- nels, hold either of the tuning buttons down.


SEEK/SCAN buttons


SEEK tuning Push the SEEK/SCAN tuning button


or for less than 0.5 seconds. SEEK tuning begins from high to low frequencies or low to high frequencies, depending on which but- ton is pressed, and stops at the next broad- casting station. Once the highest broadcast- ing station is reached, the radio continues in the SEEK mode at the lowest broadcasting station. If using the button, once the lowest broadcasting station is reached, the radio continues in the SEEK mode at the highest broadcasting station.


Heater, air conditioner and audio systems 4-19


Z X


The selected band illuminates in the dis- play.


2. Tune to the desired station. 3. Push the desired station select button for more than 1.5 seconds. For example, in the illustrations ch2 is to be memorized. The radio mutes when the select button is pushed.


4. The indicator, ch2, then illuminates in the display and the sound resumes. Memo- rizing is now complete.


5. Other station select buttons can be set in


the same manner.


If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired stations.


Cassette tape player operation Precautions on cassette tape player op- eration c To maintain good quality sound, NISSAN recommends using cassette tapes of 60 minutes or shorter in length.


c Cassette tapes should be removed


from the player when not in use. Store cassettes in their protective cases and away from direct sunlight, heat, dust moisture or magnetic sources.


c Direct sunlight can cause the cassette to become deformed. The use of de- formed cassettes may cause the cas- sette to jam in the player.


c Do not use cassettes that have peel- ing or loose labels. If used, the label could jam in the player.


c If a cassette has loose tape, insert a pencil through one of the cassette hubs and rewind the tape firmly. Loose tape may cause jamming and wavering sound quality.


c Over a period of time, the playback head, capstan and pinch roller may collect a tape coating residue as the tape is played. This residue accumu- lation can cause a weak or wavering sound and should be removed peri- odically with a head cleaning tape. If the residue is not removed periodi- cally, the player may need to be dis- assembled for cleaning.


AHA1087


Station memory operations Six stations can be set for the AM band. 12
stations can be set for the FM band (six for FM1, six for FM2). 1. Push


to select AM, FM1, or FM2.


4-20 Heater, air conditioner and audio systems


Z X


PLAY/STOP


When the button is pushed with the system turned off and a tape loaded, the system comes on and the tape plays. The word TAPE illuminates in the display. button is pushed with either When the the radio or compact disc turned on and a tape loaded, the compact disc or the radio turns off and the tape plays.


FF (Fast Forward), REW (Rewind)


button to fast


Push the forward the tape. Push the button to rewind the tape. Either REW or FF illuminates in the display. To stop the FF or REW function, press the


buttons.


, or


APS (Automatic Program Search) FF, APS REW


When the button is pushed while the tape is being played, the tape runs quickly, stops, then plays the next selection from the beginning. Push the button several times to skip several selections. Each time the button is pushed, the tape fast forwards one additional selection. This number ap- pears in the display window. The tape can


button is pushed,


be fast forwarded through up to nine selec- tions. (for example: 7 in the display indi- button has been pushed cates that the seven times to skip forward through seven selections). When the button is pushed, the selec- tion being played starts again from the beginning. Push the button several times to rewind several selections. Each time the the tape rewinds back one additional selection. The number of selections skipped appears in the display window as a negative number (for example: 27 in the display indicates that the button has been pushed seven times to rewind back through seven selec- tions). Either the FF or REW blinks in the display when the The system searches for the blank intervals between selections. If there is a blank inter- val within one selection or there is no inter- val between selections, the system may not stop in the desired or expected location.


button is pushed.


or


The cassette tape automatically changes directions to play the other side when the first side is complete.


Dolby NR (Noise Reduction)


Push the button for Dolby NR encoded tapes to reduce high frequency tape noise. The indicator illuminates in the display. Dolby NR is manufactured under license from Dolby Laboratories Licensing Corpora- tion. DOLBY NR and the double-D symbol are trademarks of Dolby Laboratories Li- censing Corporation. Metal or chrome tape usage The cassette player is automatically set to high performance play when playing a metal or chrome cassette tape.


TAPE EJECT


Push the tape.


button to eject the cassette


PROG (Program)


Push the side while the tape is being played.


button to change the tape


Heater, air conditioner and audio systems 4-21


Z X


COMPACT DISC (CD) player operation Turn the ignition key to the ACC or ON position, and carefully insert the compact disc into the slot with the label side up. The compact disc is automatically pulled into the slot and starts to play. If the radio or cassette tape is already operating, it automatically turns off and the compact disc begins to play.


CAUTION


Do not force the compact disc into the slot. This could damage the player.


CD/CHG button


When the CD/CHG button is pushed with the compact disc loaded and the tape or the radio playing, the tape or radio turns off and compact disc starts to play.


FF (Fast Forward), REW (Rewind)


fast forwarding or rewinding. When the but- ton is released, the compact disc returns to normal play speed.


APS (Automatic Program Search) FF, APS REW


When the button is pushed while the compact disc is playing, the selection fol- lowing the present one starts to play from the beginning. Push the button several times to skip several selections. Each time the button is pushed, the CD advances one additional selection. The number appears in the display window. (When the last selec- tion on the compact disc is skipped, the first selection is played.) button is pushed, the selec- When the tion being played returns to the beginning. Push the button several times to skip back several selections. Each time the but- ton is pushed, the CD moves back one selection.


PROG (Program)


When the button is pushed while the compact disc is playing, the play pattern changes as follows.


or


When the button is pushed while the compact disc is playing, the com- pact disc plays at an increased speed while 4-22 Heater, air conditioner and audio systems


RPT (Repeat) 1. The current selection is repeated. RANDOM: Selections are played at ran- dom, not following the sequence on the compact disc. The same program may be repeated twice. Normal played repeatedly in sequence. When a new compact disc is inserted, the play pattern automatically changes to the ‘‘Normal’’ play pattern.


(no symbol): All selections are


CD EJECT


When the button is pushed with a com- pact disc loaded, the compact disc ejects. button is pushed while the When the compact disc is playing, the compact disc ejects and the system turns off. If the compact disc ejects and is not removed within 10 seconds, it is pulled back into the slot. DISC indicator light CD IN appears in the display when a com- pact disc is loaded with the system on.


Z X


edges with the side of a pen or pencil as illustrated.


CAUTION


c During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely.


c The player may skip while driving on


rough roads.


c The CD player sometimes cannot function when the passenger com- partment temperature is extremely high. Decrease the temperature be- fore use.


c Do not expose the CD to direct sun-


light.


c Do not touch the playing surface of


the disc.


c Do not use 8cm discs. They may cause player damage even if using with optional adapter.


c Recordable compact discs (CD-R) may not function properly in the CD player.


LHA0049


CD care and cleaning c Handle a CD by its edges. Never touch


the surface of the disc.


c To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion. Do not use a conventional record cleaner or alcohol intended for industrial use.


c A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer


Heater, air conditioner and audio systems 4-23


Z X


FM-AM RADIO WITH COMPACT DISC (CD) CHANGER (if so equipped) ONzOFF/VOL control Turn the ignition key to the ACC or ON position, then push the PWR control knob. If you listen to the radio with the engine not running, turn the key to the ACC position. The mode (radio or CD) that was playing immediately before the system was turned off resumes playing. When no CD is loaded, the radio comes on. Pushing the PWR control knob again turns the system off. Turn the PWR control knob to the right to increase volume or to the left to decrease volume.


4-24 Heater, air conditioner and audio systems


WHA0097


Z X


or


or ) to adjust


Adjusting tone quality and speaker bal- ance Press the AUDIO button to enter the audio adjust mode: Bass!Mid!Treb!Fade!Bal Press the TUNE/FF-REV ( ) or SEEK/TRACK ( to the desired levels. The display will return to the regular radio display after 7 seconds, or you may press the AUDIO button again to return to the regular radio display. Clock operation Pressing the CLOCK button displays the clock with the radio on or off. Press the CLOCK button again to turn off the clock display. Clock set 1. Press and hold the CLOCK button until it


beeps (>2 seconds).


2. The hours will start or


TUNE/FF-REV SEEK/TRACK ( hours.


flashing. Press or the


) to adjust


or


WHA0065


3. Press the CLOCK button to switch to the


minute adjustment.


Heater, air conditioner and audio systems 4-25


Z X


4. Press TUNE/FF-REV (


or


or


) to adjust


) or the


SEEK/TRACK ( minutes.


5. Press the CLOCK button again to exit the


clock set mode.


The display will return to the regular clock display after 7 seconds, or you may press the CLOCK button again to return to the regular clock display. FM-AM radio operation FM-AM band select Push the AM or the FM button to change from AM to FM reception. The FM stereo indicator, ST, illuminates during FM stereo reception. When the ste- reo broadcast signal the radio automatically changes from stereo to mon- aural reception. Station signal strength, distance from radio transmitter, buildings, bridges, mountains, and other external influences affect radio reception. Intermittent changes in reception quality normally are caused by these exter- nal influences.


is weak,


SEEK mode at the highest broadcasting sta- tion. SCAN tuning Push the SCAN button. SCAN illuminates in the display window. Scan tuning begins from low to high frequencies or from high to low frequencies. Scan tuning stops at each broadcasting station that has sufficient sig- nal strength for 5 seconds. When scanning, SCAN blinks in the display. Pushing the SCAN button again during this 5 second period stops Scan tuning and the radio remains tuned to that station.


Using a cellular phone in or near the vehicle may influence radio reception quality.


TUNE/FF-REV


WARNING


The radio should not be tuned while driving so full attention may be given to vehicle operation.


or


Use the buttons for manual tun- ing. To move quickly through the channels, hold the tuning buttons down.


SEEK tuning


or


Push SEEK/TRACK ( ). SEEK tuning begins from low to high frequencies or high to low frequencies, depending on which but- ton is pressed, and stops at the next broad- casting station. If using the up button, once the highest broadcasting station is reached, the radio continues in the SEEK mode at the lowest broadcasting station. If using the down button, once the lowest broadcasting station is reached, the radio continues in the


4-26 Heater, air conditioner and audio systems


Z X


3. When the indicator illuminates in the station selection button, a beep will sound indicating memorization is com- plete. For FM stations, the indicator will turn green. For AM stations, the indicator will turn amber.


4. Other station select buttons can be set in


the same manner.


If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired sta- tions.


LHA0081


Station memory operation − Travel Pre- set is OFF Each preset mode (A, B or C) has 6 presets, capable of storing any combination of AM, FM and FM RDS stations. Press the PRESET ABC button to change between the presets: A!B!C The radio displays icon A, B or C to indicate which set of presets is active.


WHA0064


To store a radio station in a preset: 1. Tune to the desired station. 2. Press the desired station select button (>2 seconds.) For example, in the illus- trations ch3 is to be memorized.


Heater, air conditioner and audio systems 4-27


Z X


4. If the radio cannot find any stations, the radio displays “NO STATION” and mutes the audio.


5. If the radio cannot fill all the presets, the remaining presets are stored with 87.9
for FM, and 600 for AM.


The TUNE, SCAN, SEEK and preset memory functions are available while Travel Preset mode is on. Canceling Travel Preset Press the TRAVEL PRESET button (<1.5
seconds) the Travel Preset memory. This turns off the green indicator. The radio returns to the last used preset of A, B or C in the permanent preset memory.


to clear


LHA0082


Turning ON Travel Preset 1. Press the TRAVEL PRESET button (<1.5 seconds). The green TRAVEL PRESET button indicator turns on.


2. The radio selects the strongest stations in the area and stores them in Travel Presets A, B and C. 12 FM stations and 6 AM stations are the default settings. To change the default settings, see “Editing Travel Preset” later in this section.


3. When finished storing radio stations, the radio tunes to the first stored preset of Travel Preset A.


4-28 Heater, air conditioner and audio systems


LHA0084


Z X


Editing Travel Preset 1. Press and hold the TRAVEL PRESET button (>3 seconds) until the radio beeps to start the editing mode. The green Travel Preset indicator will flash while in TRAVEL PRESET EDIT mode.


2. The radio displays “TRAVEL EDIT” for 2
seconds and then changes to “SET A-*”. ) to se-


3. Press TUNE/FF-REV (


or


lect a mode.


4. Press the TRAVEL PRESET button to


save the mode.


5. Display is changed to “SET B-*”, repeat


steps 3 and 4.


6. Display is changed to “SET C-*”, repeat


step 3.


7. Press the TRAVEL PRESET button to exit the edit mode and return to normal mode.


*: AM, FM, FM RDS, Rock, Classic Rock, Soft Rock, Top 40, Country, Jazz, Classical, Oldies, News, Sports, Talk.


Storing Travel Preset stations in perma- nent memory 1. While in Travel Preset mode, press and hold the TRAVEL PRESET button until it beeps (>3 seconds).


2. The presets are transferred from Travel Preset memory to the permanent preset memory for A, B, and C. “PRESETS LOADED” is displayed.


3. The TRAVEL PRESET indicator turns


off.


LHA0085


Preset Scan Pressing the Preset Scan button (<1.5 sec- onds) scans the permanent preset memory that is selected (A, B or C) from 1-6 for 5
seconds. If the Travel Preset is ON, the travel preset that is selected (A, B, or C) from 1-6 is scanned for 5 seconds.


Heater, air conditioner and audio systems 4-29


Z X


RDS (Radio Data System) RDS stands for Radio Data System, and is a data information service transmitted by some radio stations on the FM band (not AM band) encoded within a regular radio broadcast. Currently, most RDS stations are in large cities, but many stations are now considering broadcasting RDS data. RDS can display: c Station call sign, such as “WHFR 98.3”. c Station name, such as “The Groove”. c Music or programming type such as


“Classical”, “Country”, or “Rock”.


c Traffic reports about delays or construc-


tion.


If the station broadcasts RDS information, the RDS icon is displayed. The RDS infor- mation will be displayed according to the option chosen in the RDS setup mode. (FM & RDS is the default.) Press the RDS button again to display the frequency for 3 sec- onds. The radio will then return to the nor- mal display. If the station does not broad- cast RDS information, the RDS icon will not be displayed.


LHA0086


All Preset Scan Pressing the Preset Scan button (>1.5 sec- onds) scans all the permanent preset memory banks (A, B or C) from 1-6 for 5
seconds. If the Travel Preset is ON, all the travel preset memory banks (A, B, or C) from 1-6 are scanned for 5 seconds. Canceling preset scan mode Pressing any button except CLOCK, EJECT and PTY cancels the Preset Scan mode.


4-30 Heater, air conditioner and audio systems


or


Setting RDS Mode Press the RDS button (>3 seconds) until the display shows “RDS SET MODE”. This display will last 2 seconds and then change to “TRAFFIC-OFF”. Press TUNE/FF-REV ) to toggle the RDS traffic mode from “OFF” to “ON”. Press the RDS button again to set your traffic mode selection. The display changes to “SHOW” for the second part of the RDS mode selection. Press TUNE/FF-REV ( ) to switch between the following RDS display modes: c “FM & RDS”: the radio display will show the station’s broadcast frequency and the station’s name.


or


c “RDS ONLY”: the radio display will show


the station’s name only.


c “RDS TEMP”: the radio display will show the station’s name for 5 seconds and then display only the radio station’s broadcast frequency.


PTY (Program Type) PTY can be used to search for a certain program type. Certain areas have a limited number of stations that transmit RDS. Many stations transmit call letters and frequencies


Z X


only. Searching or scanning by program type may yield a limited number of selec- tions. 1. Press the PTY button. The display changes from “RDS PTY SEARCH” to “SELECT BY TUNE”.


or


2. Press


TUNE/FF-REV


up/down button to choose a specific pro- gram type: ROCK, CLASSIC ROCK, SOFT ROCK, TOP 40, COUNTRY, JAZZ, CLASSICAL, OLDIES, NEWS, SPORTS, TALK, ANY 3. Press the SEEK or SCAN button to search for the next station with the se- lected PTY. The SCAN icon flashes when the SCAN button is pressed. The radio continues to seek or scan until a radio station is found matching the se- lected PTY.


4. Press the PTY button again to cancel the


PTY SEEK mode.


Compact disc (CD) operation Turn the ignition key to the ACC or ON position.


CAUTION


c Do not force a compact disc (CD) into the CD insert slot. This could damage the CD and/or CD changer. c Trying to load a CD with the CD door closed could damage the CD and/or CD changer.


CD button


When the CD button is pressed with a compact disc loaded and the radio playing, the radio turns off and the last used com- pact disc starts to play.


LHA0075


CD Loading


Press the LOAD button to start CD loading mode. The following sequence will occur: 1. The green indicator on the lowest avail- able disc select button will start blinking. (Same as preset memory button). The display shows “Please Wait”.


2. The display changes to “Insert Disc” for


a maximum of 15 seconds.


Heater, air conditioner and audio systems 4-31


Z X


Disc Play Press the CD button. If a CD is loaded and the radio is playing, the radio turns off and the last loaded disc starts to play.


3. During the 15 second interval, insert the disc. The display changes to “Loading Disc”.


4. The CD will play after the disc is set to a


play position.


5. The indicator changes from blinking green to solid green and the display changes to show the Disc number icon, Disc number, Track number and Elapsed time.


All disc loading 1. Press and hold the LOAD button until the


radio beeps (>1.5 seconds).


2. The green indicator on the lowest avail- able disc select button will start blinking. (Same as preset memory button). The display shows “Please Wait”.


3. The display changes to “Insert Disc” for


a maximum of 15 seconds.


4. During the 15 second interval, insert the disc. The display changes to “Loading Disc”.


5. The indicator changes from blinking


green to solid green.


then the last


7. Steps 2-5 are repeated until all discs are loaded, loaded disc will begin to play. The display shows the Disc number, Track number and Elapsed Time.


Selected disc loading 1. Press a disc select button whose indica- tor is off. The display shows “Please Wait”.


2. The green indicator starts blinking and the display shows “Insert Disc” for 15
seconds.


3. Insert the CD. The display shows “Load-


ing Disc”.


4. The CD will play after the disc is set to a


play position.


5. The indicator color changes from blink- ing green to solid green and the display shows the Disc icon, Disc number, Track number and Elapsed Time.


If a disc is not inserted within 15 seconds or if the load button is pressed during load sequence, the entire disc load sequence will be canceled.


6. The disc number icon is turned on. 4-32 Heater, air conditioner and audio systems


Z X


forward) REW


FF (fast (rewind) buttons or


) but- When the TUNE/FF-REV ( ton is pressed while the compact disc is playing, the compact disc plays at an in- creased speed while fast forwarding or re- winding. When the button is released, the CD returns to normal play speed.


LHA0076


Selected disc play 1. Press the disc select button whose disc


icon is displayed.


2. The indicator blinks green during the change and the display shows “Chang- ing Disc”.


3. The CD plays after the disc is set to a


play position.


4. The indicator changes from blinking green to solid green and the display shows the Disc number, Track number and Elapsed Time.


SEEK/TRACK buttons


When is pressed while the compact disc is playing, the selection following the present one starts to play from the begin- several times to skip sev- ning. Press eral selections. Each time the button is pressed, the CD advances one additional selection. The track number appears in the display window. (When the last selection on the compact disc is skipped, the first selec- tion is played.) When the selection being played returns to the beginning. Press several times to skip back several selec- tions. Each time the button is pressed, the CD moves back one selection. If the play pattern is in MIX mode when the button is pressed, the next random selection will be played.


is pressed,


LHA0077


Repeat/Mix


Press the RPT MIX button to change CD play patterns: Repeat!Mix!All Mix!Normal Play Repeat Press the RPT MIX button (<1.5 seconds) once to repeat the current track. The “1” icon is turned on, and the display shows “Repeat Track” for 2 seconds. The display then shows the Track number and Elapsed time as normal.


Heater, air conditioner and audio systems 4-33


Z X


All Discs, 1 Track Press and hold the SCAN button (>1.5
seconds) to scan the first track of all the loaded discs for 7 seconds per track. The display shows “All Disc Scan” for 2 sec- onds, and then shows the track number and elapsed time as normal. The SCAN icon is flashed during Scan mode. The Scan mode is cancelled once it scans through all the loaded discs, or if the SCAN button is pressed during Scan mode.


Mix Press the RPT MIX button (<1.5 seconds) again to start shuffle play of the current disc. The “MIX” icon is turned on and the display shows “Mix Tracks” for 2 seconds. The display then shows the Track number and Elapsed time as normal. All Mix Press the RPT MIX button (<1.5 seconds) again to start shuffle play of all discs. The “MIX” icon is turned on, and the display shows “Mix All Tracks” for 2 seconds. The display then shows the Track number and Elapsed time as normal. Also, the indicators of the loaded discs are turned on with amber color. (Green for current disc.) Normal Play Press the RPT MIX button (<1.5 seconds) again to change to normal play mode. The “MIX” icon and the amber LED’s are turned off. The display shows “Normal Play” for 2
seconds. The display then shows the Track number and Elapsed time as normal.


LHA0078


tracks of


CD Scan 1 Disc All Tracks Press the SCAN button (<1.5 seconds) to scan all the current disc for 7
seconds per track. The display shows “Disc Scan” for 2 seconds, and then shows the track number and elapsed time as normal. The SCAN icon is flashed during Scan mode. The Scan mode is cancelled once it scans through all tracks on the disc, or if the SCAN button is pressed during Scan mode.


4-34 Heater, air conditioner and audio systems


Z X


4. The indicator and symbol for the disc are


turned off. Select a disc 1. Press the desired disc, then press the


EJECT button.


LHA0079


Eject CD


Current disc 1. Press the EJECT button. 2. The green indicator starts to blink and the display shows “Disc Eject” for 2
seconds. The display then changes to “Ejecting Disc”.


3. The disc ejects. Remove the disc. (If the disc is not removed within 15 seconds, the disc will reload.)


2. The green indicator starts blinking and the display shows “Disc Eject” for 2
seconds. The display then changes to “Ejecting Disc”.


3. The disc ejects. Remove the disc. (If disc is not removed within 15 seconds, disc will reload.)


4. The indicator and symbol for the disc are


turned off.


LHA0080


All discs 1. Press and hold the EJECT button until it


beeps (>1.5 seconds).


2. Lowest used disc number indicator blinks green and display shows “All Disc


Heater, air conditioner and audio systems 4-35


Z X


Eject” for 2 seconds. The display then changes to “Ejecting Disc”.


3. When a disc is removed, the indicator and disc icon will be turned off, and then the next disc will emerge, and so on.


4. The display will be turned off after all


discs are ejected and removed.


If a disc is not removed within 15 seconds, or if the EJECT button is pressed again during the Eject sequence, the entire disc Eject sequence will be canceled.


LHA0049


CD care and cleaning: c Handle a CD by its edges. Never touch


the surface of the disc.


c To clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion. Do not use a conventional record cleaner or alcohol intended for industrial use.


c A new disc may be rough on the inner and outer edges. Remove the rough edges by rubbing the inner and outer


4-36 Heater, air conditioner and audio systems


edges with the side of a pen or pencil as illustrated.


CAUTION


c During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely.


c The player may skip while driving on


rough roads.


c The CD player sometimes cannot function when the passenger com- partment temperature is extremely high. Decrease the temperature be- fore use.


c Do not expose the CD to direct sun-


light.


c Do not touch the playing surface of


the disc.


c Do not use 8 cm discs. They may cause player damage even if using with the optional adapter.


c Recordable compact discs (CD-R) may not function properly in the CD player.


Z X


CAR PHONE OR CB RADIO


ANTENNA Window antenna The antenna pattern is printed inside the rear window.


When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the following cautions, otherwise the new equipment may adversely affect the MFI (Multiport Fuel Injection) system and other electronic parts.


CAUTION


c Do not place metalized film near the rear window glass or attach any metal parts to it. This may cause poor reception or noise.


c When cleaning the inside of the rear window, be careful not to scratch or damage the rear window antenna. Lightly wipe along the antenna with a dampened soft cloth.


WARNING


c A cellular telephone should not be used while driving so full attention may be given to vehicle operation. Some jurisdictions prohibit the use of cellular telephones while driving. c If you must make a call while your vehicle is in motion, the hands free cellular phone operational mode (if so equipped) is highly recom- mended. Exercise extreme caution at all times so full attention may be given to vehicle operation.


c If a conversation in a moving vehicle requires you to take notes, pull off the road to a safe location and stop your vehicle before doing so.


CAUTION


c Keep the antenna as far as possible away from the Engine Control Mod- ule (ECM).


c Keep the antenna wire more than 8
in. (20 cm) away from the Multiport Fuel Injection harness. Do not route the antenna wire next to any har- ness.


c Adjust the antenna standing-wave ratio as recommended by the manu- facturer.


c Connect the ground wire from the


CB radio chassis to the body.


c For details, consult an authorized


NISSAN dealer.


Heater, air conditioner and audio systems 4-37


Z X


MEMO


4-38 Heater, air conditioner and audio systems


Z X


5 Starting and driving


Precautions when starting and driving...................5-2
Exhaust gas (carbon monoxide) .......................5-2
Three-way catalyst ............................................5-2
Avoiding collision and rollover...........................5-3
Drinking alcohol/drugs and driving....................5-3
Ignition switch.........................................................5-4
Automatic transmission .....................................5-4
Manual transmission..........................................5-5
Key positions .....................................................5-5
Nissan vehicle immobilizer system (NVIS)................................................................5-6
Before starting the engine......................................5-6
Starting the engine.................................................5-7
Driving the vehicle..................................................5-7
Automatic transmission .....................................5-7
Manual transmission........................................5-11
Parking brake .......................................................5-12
Cruise control (if so equipped).............................5-13
Precautions on cruise control..........................5-13


Cruise control operations ................................5-14
Break-in schedule ................................................5-15
Increasing fuel economy ......................................5-15
Parking/parking on hills........................................5-16
Power steering .....................................................5-17
Brake system........................................................5-17
Braking precautions.........................................5-17
Anti-lock brake system (ABS) (if so equipped)................................................5-18
Cold weather driving ............................................5-19
Freeing a frozen door lock ..............................5-19
Anti-freeze .......................................................5-19
Battery .............................................................5-19
Draining of coolant water ................................5-19
Tire equipment.................................................5-20
Special winter equipment ................................5-20
Driving on snow or ice.....................................5-20
Engine block heater (if so equipped) ..............5-21


Z X


PRECAUTIONS WHEN STARTING AND DRIVING


WARNING


c Do not


leave children,


impaired adults, or pets alone in your vehicle. They could accidentally injure them- selves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or pos- sibly fatal injuries to people or ani- mals.


c Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured. Keep the car locked, with the trunk closed, when not in use, and prevent children’s access to car keys.


EXHAUST GAS (Carbon Monoxide)


WARNING


Do not breathe exhaust gases; they contain colorless and odorless carbon


5-2 Starting and driving


monoxide. Carbon monoxide is dan- gerous. It can cause unconsciousness or death. c If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.


c Do not run the engine in closed


spaces such as a garage.


c Do not park the vehicle with the engine running for any extended length of time.


c Keep the trunk lid closed while driv- ing, otherwise exhaust gases could be drawn into the passenger com- partment. If you must drive with the trunk lid open, follow these precau- tions: 1. Open all the windows. 2. Set the


air recirculation but- ton (if so equipped) to the off position and turn the fan control dial to 4 (high) to circulate the air.


c If electrical wiring or other cable connections must pass to a trailer through the seal on the trunk lid or the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle.


c The exhaust system and body should be inspected by a qualified mechanic whenever: a. The vehicle is raised for service. b. You suspect that exhaust fumes are entering into the passenger compartment.


c. You notice a change in the sound


of the exhaust system.


d. You have had an accident involv- ing damage to the exhaust system, underbody, or rear of the vehicle.


THREE-WAY CATALYST The three-way catalyst is an emission con- trol device installed in the exhaust system. Exhaust gases in the three-way catalyst are burned at high temperatures to help reduce pollutants.


Z X


WARNING


c The exhaust gas and the exhaust- system are very hot. Keep people, animals or flammable materials away from the exhaust system com- ponents.


c Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire.


CAUTION


c Do not use leaded gasoline. Deposits from leaded gasoline seriously re- duce the three way catalyst’s ability to help reduce exhaust pollutants.


c Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause over- rich fuel flow into the three-way cata- lyst, causing it to overheat. Do not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating condi- tions are detected. Have the vehicle inspected promptly by an authorized NISSAN dealer.


c Avoid driving with an extremely low fuel level. Running out of fuel could- cause the engine to misfire, damag- ing the three way catalyst.


c Do not race the engine while warm-


ing it up.


c Do not push or tow your vehicle to


start the engine.


AVOIDING COLLISION AND ROLLOVER


WARNING


Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accident.


Be alert and drive defensively at all times. Obey all traffic regulations. Avoid excessive speed, high speed cornering, or sudden steering maneuvers, because these driving practices could cause you to lose control of your vehicle. As with any vehicle, loss of control could result in a collision with other vehicles or objects, or cause the vehicle to roll over, particularly if the loss of control causes the vehicle to slide


sideways. Be attentive at all times, and avoid driving when tired. Never drive when under the influence of alcohol or drugs (in- cluding prescription or over-the-counter drugs which may cause drowsiness). Al- ways wear your seat belt as outlined in the ‘‘Seats, restraints and supplemental air bag systems’’ section of this manual, and also instruct your passengers to do so. DRINKING ALCOHOL/DRUGS AND DRIVING


WARNING


Never drive under the influence of alco- hol or drugs. Alcohol in the bloodstream reduces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an accident, alcohol can increase the severity of the injury.


NISSAN is committed to safe driving. How- ever, you must choose not to drive under the influence of alcohol. Every year thou- sands of people are injured or killed in alcohol related accidents. Although the local Starting and driving 5-3


Z X


IGNITION SWITCH


is considered to be laws vary on what legally intoxicated, the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol. Remember, drinking and driving don’t mix! And that’s true for drugs, too (over the counter, prescription, and illegal drugs). Don’t drive if your ability to operate your vehicle is impaired by alcohol, drugs, or some other physical condition.


ASD1014


AUTOMATIC TRANSMISSION On automatic transmission models the igni- tion lock is designed so the key cannot be turned to LOCK and removed until the shift selector lever is moved to the P (Park) position. When removing the key from the ignition, make sure the shift selector lever is in the P (Park) position. If the key cannot be turned to the LOCK position, proceed as follows to remove the key.


5-4 Starting and driving


1) Move the shift selector lever into the P


(Park) position.


2) Turn the ignition key slightly toward the


ON position.


3) Turn the key to the LOCK position. 4) Remove the key. The shift lever is designed so it cannot be moved out of P (Park) and into any of the other gear positions if the ignition key is turned to OFF or if the key is removed from the switch. The shift selector lever can be moved if the ignition switch is in the ACC posi- tion. This allows the vehicle to be moved if the battery is discharged. The shift selector lever can also be moved if the ignition switch is in the ON position and the foot brake pedal is depressed. There is an OFF position between the LOCK and ACC positions. The OFF posi- tion is indicated by a ‘‘1’’ on the key cylinder. When the ignition is in OFF, the steering wheel is not locked. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clock- wise from the straight up position.


Z X


To lock the steering wheel, turn the key to the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left.


WARNING


Never remove or turn the key to the LOCK position while driving. The steer- ing wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.


ASD1015


MANUAL TRANSMISSION The ignition switch includes an anti-theft steering lock device. The key can only be removed when the ignition switch is in the LOCK position. On manual transmission models, to turn the ignition key to LOCK from ACC or ON, turn the key to OFF, push the key in, then turn the key to LOCK. In order for the steering wheel to be locked, it must be turned about 1/8 of a turn clock- wise from the straight up position.


To lock the steering wheel, turn the key to the LOCK position. Remove the key. To unlock the steering wheel, insert the key and turn it gently while rotating the steering wheel slightly right and left.


WARNING


Never remove or turn the key to the LOCK position while driving. The steer- ing wheel will lock. This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury.


KEY POSITIONS LOCK Normal parking position (0) OFF (1) The engine can be turned off without locking the steering wheel. ACC (Accessories) (2) This position activates electrical accesso- ries such as the radio when the engine is not running. ON Normal operating position (3) This position turns on the ignition system and the electrical accessories.


Starting and driving 5-5


Z X


If this procedure allows the engine to run, NISSAN recommends placing the regis- tered NVIS key on a separate key ring to avoid interference from other devices.


BEFORE STARTING THE ENGINE


c Make sure the area around the vehicle is


clear.


c Maintenance items listed here should be checked periodically, for example, each time you check engine oil.


c Check that all windows and lights are


clean.


c Visually inspect tires for their appearance and condition. Also check tires for proper inflation.


c Lock all doors. c Position seat and adjust head restraints. c Adjust inside and outside mirrors. c Fasten seat belts and ask all passengers


to do likewise.


c Check the operation of warning lights when key is turned to the ON (3) position. See and chimes’’ in the ‘‘Instruments and con- trols’’ section.


‘‘Warning/Indicator


lights


START (4) This position activates the starter motor, which starts the engine. NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) The Nissan Vehicle Immobilizer System (NVIS) will not allow the engine to run without the use of the registered NVIS key. If the engine fails to run using the registered NVIS key, it may be due to interference caused by another NVIS key, an automated toll road device or automated payment de- vice on the key ring. Restart the engine using the following procedures: 1. Leave the ignition switch in the ON posi-


tion for approximately 5 seconds.


2. Turn the ignition switch to the OFF or LOCK position and wait approximately 5
seconds.


3. Repeat step 1 and 2 again. 4. Restart the engine while holding the de- vice (which may have caused the inter- ference) separate from the registered NVIS key.


5-6 Starting and driving


Loading...
x