1999 Nissan Altima Owners Manual

As the vehicle owner, you are the only one who can ensure that your vehicle receives proper maintenance. You are a vital link in the maintenance chain. General maintenance General maintenance includes those items which should be checked during normal day-to-day operation of the vehicle. They are essential if your vehicle is to continue to operate properly. It is your responsibility to perform these maintenance procedures regularly as prescribed. These checks or inspections can be done by yourself, a qualified technician or, if you prefer, an authorized NISSAN dealer. 9-2 Maintenance

Periodic maintenance The maintenance items listed under peri- odic maintenance are required to be ser- viced at regular intervals. However, under severe driving conditions, additional or more frequent maintenance is required. Where to go for service If maintenance service is required or your vehicle appears to malfunction, have the systems checked and tuned by an autho- rized NISSAN dealer. NISSAN technicians are well-trained spe- cialists who are kept up to date with the latest service information through technical bulletins, service tips, and in-dealership training programs. They are completely qualified to work on NISSAN vehicles be- fore they work on your vehicle, rather than after they have worked on it. You can be confident that an authorized NISSAN dealer’s service department per- forms the best job to meet the maintenance requirements on your vehicle — in a reliable and economic way.

GENERAL MAINTENANCE

During the normal day-to-day operation of the vehicle, general maintenance should be per- formed regularly as prescribed in this section. If you detect any unusual sounds, vibrations or smells, be sure to check for the cause or have an authorized NISSAN dealer do it promptly. In addition, you should notify an authorized NISSAN dealer if you think repairs are required. When performing any checks or mainte- nance work, closely observe the precautions in the ‘‘Do-it-yourself’’ section of this manual. OUTSIDE THE VEHICLE The maintenance items listed here should be performed from time to time, unless otherwise specified. Additional information on the items marked with an ‘‘*’’ can be found in the ‘‘Do-it-yourself’’ section of this manual. Tires* — Check the pressure with a gauge periodically when at a service station, in- cluding the spare, and adjust to the speci- fied pressure if necessary. Check carefully for damage, cuts or excessive wear. Wheel nuts* — When checking the tires, make sure no wheel nuts are missing, and check for any loose wheel nuts. Tighten if necessary.

Z X

Tire rotation* — Tires should be rotated every 7,500 miles (12,000 km). Wheel alignment and balance — If the vehicle should pull to either side while driv- ing on a straight and level road, or if you detect uneven or abnormal tire wear, there may be a need for a wheel alignment. If the steering wheel or seat vibrates at normal highway speeds, wheel balancing may be needed. Windshield wiper blades* — Check for cracks or wear if they do not wipe properly. Doors and hood — Check that all doors and the hood operate properly. Also ensure all latches lock securely. Lubricate hinges, latches, rollers and links if necessary. Make sure the secondary latch keeps the hood from opening when the primary latch is released. When driving in areas using road salt or other corrosive materials, check lubrication frequently. Lights* — Make sure the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely. Also check headlight aim.

INSIDE THE VEHICLE The maintenance items listed here should be checked on a regular basis, such as when performing periodic maintenance, cleaning the vehicle, etc. Additional information on the following items with an ‘‘*’’ is found in the ‘‘Do-it- yourself’’ section of this manual. Warning lights and chimes — Make sure all warning lights and buzzers/chimes are operating properly. Windshield wiper and washer* — Check that the wipers and washer operate properly and that the wipers do not streak. Windshield defroster — Check that the air comes out of the defroster outlets properly and in sufficient quantity when operating the heater or air conditioner. Steering wheel — Check for changes in the steering conditions, such as excessive freeplay, hard steering or strange noises. Seats — Check seat position controls such as seat adjusters, seatback recliner, etc. to ensure they operate smoothly and all latches lock securely in every position. Check that the head restraints move up and down

smoothly and the locks (if so equipped) hold securely in all latched positions. Seat belts — Check that all parts of the seat belt system (for example, buckles, anchors, adjusters and retractors) operate properly and smoothly, and are installed securely. Check the belt webbing for cuts, fraying, wear or damage. Accelerator pedal — Check the pedal for smooth operation and make sure the pedal does not catch or require uneven effort. Keep the floor mat away from the pedal. Clutch pedal* — Make sure the pedal operates smoothly and check that it has the proper free travel. Brakes — Check that the brakes do not pull the vehicle to one side when applied. Brake pedal and booster* — Check the pedal for smooth operation and make sure it has the proper distance under it when de- pressed fully. Check the brake booster func- tion. Be certain to keep the floor mat away from the pedal. Parking brake* — Check that the lever has the proper travel and confirm that your vehicle is held securely on a fairly steep hill with only the parking brake applied.

Maintenance 9-3

Z X

Automatic transmission ‘‘Park’’ mecha- nism — On a fairly steep hill check that your vehicle is held securely with the shift selec- tor lever in the P (Park) position without applying any brakes. UNDER THE HOOD AND VEHICLE The maintenance items listed here should be checked periodically, such as each time you check the engine oil or refuel. Additional information on the items marked with an “*” can be found in the “Do-it-yourself’’ section of this manual. Windshield washer fluid* — Check that there is adequate fluid in the tank. Engine coolant level* — Check the cool- ant level when the engine is cold. Radiator and hoses — Check the front of the radiator and clean off any dirt, insects, leaves, etc., that may have accumulated. Make sure the hoses have no cracks, de- formation, rot or loose connections. Brake and (if so equipped) clutch fluid levels* — Make sure that the brake and clutch fluid level are between the MIN and MAX lines on each reservoir. 9-4 Maintenance

Battery* — Check the fluid level in each cell. It should be between the MAX and MIN lines. Engine drive belts* — Make sure the drive belts are not frayed, worn, cracked or oily. Engine oil level* — Check the level after parking the vehicle on a level surface, with the engine off. Wait a few minutes for the oil to drain back into the oil pan. Power steering fluid level* and lines — Check the level when the fluid is cold and with the engine off. Check the lines for proper attachment, leaks, cracks, etc. Automatic transmission fluid level* — Check the level after putting the shift selec- tor lever in P (Park) with the engine idling at operating temperature. Exhaust system — Make sure there are no cracks, holes, loose joints or supports. If the sound of the exhaust seems unusual or there is a smell of exhaust fumes, immedi- ately have the exhaust system inspected by a qualified individual. (See the carbon mon- oxide warning in the ‘‘Starting and driving’’ section of this manual.) Underbody — The underbody is frequently

exposed to corrosive substances such as those used on icy roads or to control dust. It is very important to remove these sub- stances from the underbody, otherwise rust may form on the floor pan, frame, fuel lines and exhaust system. At the end of winter, the underbody should be thoroughly flushed with plain water, especially those areas where mud and dirt may accumulate. See the ‘‘Appearance and care’’ section for ad- ditional information. Fluid leaks — Check under the vehicle for fuel, oil, water or other fluid leaks after the vehicle has been parked for a while. Water dripping from the air conditioner after use is normal. If you should notice any leaks or if gasoline fumes are evident, check for the cause and have it corrected immediately by an authorized NISSAN dealer.

Z X

PERIODIC MAINTENANCE SCHEDULES

To ensure smooth, trouble-free, safe and economical driving, NISSAN provides two periodic maintenance schedules that may be used, depending upon the conditions in which you usually drive. These schedules contain both distance and time intervals, up to 60,000 miles (96,000 km)/48 months. For most people, the odometer reading indi- cates when service is needed. However, if you drive very little, your vehicle should be serviced at the regular time intervals shown in the schedules. After 60,000 miles (96,000 km)/48 months, continue peri- odic maintenance same mileage/time intervals. SCHEDULE ONE Follow Periodic Maintenance Schedule 1 if your driving habits frequently include one or more of the following driving conditions: c Repeated short trips of less than 5

the

at

miles (8 km).

c Extensive idling and/or low speed driving for long distances, such as police, taxi or door-to-door delivery use.

c Driving in dusty conditions. c Driving on rough, muddy, or salt

spread roads.

c Towing a trailer, using a camper or a

car-top carrier.

SCHEDULE TWO Follow Periodic Maintenance Schedule 2 if none of the driving conditions shown in Schedule 1 apply to your driving habits.

c Repeated short trips of less than 10
miles (16 km) with outside tempera- tures below freezing.

c Operating the vehicle in hot weather during in stop-and-go ‘‘rush hour’’ traffic.

Maintenance 9-5

Z X

Schedule One Abbreviations: R = Replace I = Inspect. Correct or replace if necessary.

MAINTENANCE OPERATION

Perform at number of miles, kilometers or months, whichever comes first.

Miles x 1,000
(km x 1,000) Months

3.75
(6)

7.5 11.25
(12) (18)

MAINTENANCE INTERVAL

[ ]: At the mileage intervals only

15 18.75 22.5 26.25
(24) (42) 21
12

(30) 15

(36) 18

30 33.75 37.5 41.25
(48) (66) 33
24

(54) 27

(60) 30

45 48.75 52.5 56.25
(72) (90) 45
36

(78) 39

(84) 42

Emission control system maintenance Drive belts Air cleaner filter EVAP vapor lines Fuel lines Fuel filter Engine coolant Engine oil Engine oil filter Spark plugs (Use PLATINUM-TIPPED type) Intake & exhaust valve clearance

See NOTE (1) See NOTE (2)

See NOTE (3)* See NOTE (4)

See NOTE (5)*

[R] I* I*

60
(96) 48

I* [R] I* I*

R* [R]

NOTE: (1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months.

(2) If operating mainly in dusty conditions, more frequent maintenance may be required. (3) If vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are either

extremely low or extremely high, the filters might become clogged. In such an event, replace them immediately.

(4) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months. (5) If valve noise increases, inspect valve clearance. * Maintenance items and intervals marked with an ‘‘*’’ are recommended by NISSAN for reliable vehicle operation. The owner need not perform such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are required.

9-6 Maintenance

Z X

Abbreviations: I = Inspect. Correct or replace if necessary.

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Perform at number of miles, kilometers or months, whichever comes first.

Miles x 1,000

(km x 1,000)

Months

7.5

(12)

15

(24)

12

22.5

(36)

18

30

(48)

24

37.5

(60)

30

45

(72)

36

52.5

(84)

42

60

(96)

48

Chassis and body maintenance

Brake lines & cables

Brake pads, rotors, drums & linings

Manual transmission oil & automatic transmission fluid

See NOTE (2)

Steering gear & linkage, axle & suspension parts

Exhaust system

Drive shaft boots

Supplemental air bag system

See NOTE (1)

NOTE: (1) Inspect the supplemental air bag system 10 years after the date of manufacture noted on the FMVSS certification label. (2) If towing a trailer, using a camper or a car-top carrier, or driving on rough or muddy roads, change (not just inspect)

oil at every 30,000 miles (48,000 km) or 24 months.

Maintenance 9-7

Z X

Schedule Two Abbreviations: R = Replace I = Inspect. Correct or replace if necessary.

[ ]: At the mileage intervals only

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Perform at number of miles, kilometers or months, whichever comes first.

Emission control system maintenance Drive belts Air cleaner filter EVAP vapor lines Fuel lines Fuel filter Engine coolant Engine oil Engine oil filter Spark plugs (Use PLATINUM-TIPPED type) Intake & exhaust valve clearance

Miles x 1,000
(km x 1,000) Months

See NOTE (1)

See NOTE (2)* See NOTE (3)

See NOTE (4)*

7.5
(12)

15
(24) 12

22.5
(36) 18

30
(48) 24

[R] I* I*

37.5
(60) 30

45
(72) 36

52.5
(84) 42

60
(96) 48

I* [R] I* I*

R* [R]

NOTE: (1) After 60,000 miles (96,000 km) or 48 months, inspect every 15,000 miles (24,000 km) or 12 months.

(2) If vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are either

extremely low or extremely high, the filters might become clogged. In such an event, replace them immediately.

(3) After 60,000 miles (96,000 km) or 48 months, replace every 30,000 miles (48,000 km) or 24 months. (4) If valve noise increases, inspect valve clearance. * Maintenance items and intervals marked with an ‘‘*’’ are recommended by NISSAN for reliable vehicle operation. The owner need not perform such maintenance in order to maintain the emission warranty or manufacturer recall liability. Other maintenance items and intervals are required.

9-8 Maintenance

Z X

Abbreviations: I = Inspect. Correct or replace if necessary.

MAINTENANCE OPERATION

MAINTENANCE INTERVAL

Perform at number of miles, kilometers or months, whichever comes first.

Miles x 1,000
(km x 1,000) Months

7.5
(12)

15
(24) 12

22.5
(36) 18

30
(48) 24

37.5
(60) 30

45
(72) 36

52.5
(84) 42

60
(96) 48

Chassis and body maintenance Brake lines & cables Brake pads, rotors, drums & linings Manual transmission oil & automatic transmission fluid Steering gear & linkage, axle & suspension parts Exhaust system Drive shaft boots Supplemental air bag system

See NOTE (1)

NOTE: (1) Inspect the supplemental air bag system 10 years after the date of manufacture noted on the FMVSS certification label.

Maintenance 9-9

Z X

EXPLANATION OF MAINTENANCE ITEMS

Additional information on the following items marked with an ‘‘*’’ is found in the ‘‘Do-it- yourself’’ section of this manual. Emission control system maintenance Drive belts* — Check drive belts for wear, fraying or cracking and also for proper ten- sion. Replace any damaged drive belts. Air cleaner filter — Under normal driving conditions, the air cleaner filter should be replaced in accordance with the mainte- nance schedule. However, driving the ve- hicle in dusty areas may cause rapid clog- ging of the element may have to be replaced more frequently. Evap vapor lines — Check vapor lines and connections for leaks, looseness or deterio- ration. If leaks are found, replace them. Fuel lines — Check the fuel hoses, piping and connections for leaks, looseness or deterioration. Replace any damaged parts. Fuel filter — If the vehicle is operated under extremely adverse weather conditions or in areas where ambient temperatures are ei- ther extremely low or extremely high, the 9-10 Maintenance

the element. Consequently,

In such an

filter might become clogged. event, replace the filter immediately. Engine coolant* — Drain and flush the cooling system. Engine oil & oil filter* — Under normal driving conditions, the engine oil and oil filter should be replaced in accordance with the maintenance schedule. However, under se- vere driving conditions, they may have to be replaced more frequently. Spark plugs* — Replace with new plugs having the correct heat range. Intake & exhaust valve clearance — Check the valve clearance if valve noise increases. Chassis and body maintenance Brake lines & cables — Check the brake lines and hoses (including brake booster vacuum hoses, connections & check valve) and parking brake cables for proper attach- ment, leaks, cracks, chafing, abrasion, de- terioration, etc. Brake pads, rotors, drums & linings — Check these and the other neighboring brake components for wear, deterioration and leaks. Under severe driving conditions, they may have to be inspected more frequently.

Manual & automatic transmission fluid* — Check the fluid level and visually inspect for signs of leakage. Under severe driving conditions, the fluid should be replaced at the specified interval. Steering gear & linkage, axle & suspen- sion parts, and drive shaft boots — Check for damage, looseness and leakage of oil or grease. Under severe driving con- ditions, inspection should be performed more frequently. Exhaust system — Visually check the ex- haust pipes, muffler, and hangers for proper attachment, leaks, cracks, chafing, abra- sion, deterioration, etc. Under severe driv- ing conditions, inspection should be per- formed more frequently. Supplemental air bag system — Check the supplemental air bag system compo- nents for proper attachment, damage, de- formities, cracks, rust, etc. Work around and on the supplemental air bag system should be done by an authorized NISSAN dealer.

Z X

10 Technical and consumer information

Capacities and recommended fuel/lubricants......10-2
Fuel recommendation...........................................10-3
Engine oil and oil filter recommendation..............10-5
Recommended SAE viscosity number.................10-6
Air conditioner system refrigerant and lubricant recommendations ..................................10-7
Engine ..................................................................10-8
Wheel/tire size......................................................10-9
Dimensions and weights ......................................10-9
Registering your vehicle in another country ......10-10
Vehicle identification ..........................................10-10
Vehicle identification number plate ....................10-10
Vehicle identification number (chassis number)................................................10-10

Engine serial number .........................................10-11
F.M.V.S.S. certification label..............................10-11
Emission control information label .....................10-12
Tire placard ........................................................10-12
Air conditioner specification label.......................10-12
Installing front license plate................................10-13
Vehicle loading information................................10-13
Trailer towing......................................................10-14
Uniform tire quality grading................................10-18
Emission control system warranty .....................10-19
Reporting safety defects (USA) .........................10-19
Readiness for inspection/maintenance (I/M) test (US only) .....................................................10-20

Z X

CAPACITIES AND RECOMMENDED FUEL/ LUBRICANTS The following are approximate capacities. The actual refill capacities may be a little different. When refilling, follow the procedure described in the ‘‘Do-it-yourself’’ section to determine the proper refill capacity.

Fuel

Engine oil *7

Drain and refill

With oil filter change Without oil filter change

Cooling system

With reservoir Reservoir

Manual transaxle gear oil

Automatic transaxle fluid

Power steering fluid

Brake and clutch fluid

Capacity (Approximate)

US

measure

15-7/8 gal

3-5/8 qt 3-3/8 qt

7-3/4 qt 3/4 qt

Imp

measure

13-1/4 gal

3 qt

2-7/8 qt

6-3/8 qt 5/8 qt

Liter

60

3.4
3.2

7.3
0.7

9-1/2 to 10-1/8 pt

7-7/8 to 8-1/2 pt

4.5 to 4.8

10 qt

1 qt

8-1/4 qt

3/4 qt

9.4

0.9

Refill to the proper level according to the instructions in the ‘‘Do-it-yourself’’ section.

Recommended Fluids and Lubricants

Unleaded gasoline with an octane rating of at least 87
AKI (RON 91)*1
c API Certification Mark *2 *3
c API grade SG/SH, Energy Conserving II or API grade

SJ, Energy Conserving *2 *3

c ILSAC grade GF-II *2 *3

50% Genuine NISSAN Anti-freeze coolant or equivalent 50% Demineralized water or Distilled water API GL-4, Viscosity SAE 80W-90 only Nissan Matic ‘D’ (Continental U.S. and Alaska) or Genuine Nissan Automatic Transmission Fluid (Canada). *4
Type DEXRONTM III or equivalent Genuine Nissan Brake Fluid*5 or equivalent DOT 3 (US FMVSS No. 116) NLGI No. 2 (Lithium soap base) HFC-134a (R-134a)*6
Nissan A/C System Oil Type R or exact equivalent*6

Multi-purpose grease Air conditioning system refrigerant Air conditioning system lubricant *1: For further details, see ‘‘Fuel recommendation.’’ *2: For further details, see ‘‘Engine oil and oil filter recomendations.’’ *3: For further details, see ‘‘Recommended SAE engine oil viscosity.’’ *4: DexronTM III/MerconTM or equivalent may also be used. Outside the Continental United States and Alaska contact a NISSAN dealership for more information

— — —

— — —

— — —

regarding suitable fluids, including recommended brand(s) of DexronTM III/MerconTM Automatic Transmission Fluid.

*5: Available in mainland USA through your NISSAN dealer. *6: For further details, see ‘‘Air conditioner specification label.’’ *7: For further details, see ‘‘Changing engine oil.’’

10-2 Technical and consumer information

Z X

FUEL RECOMMENDATION Your vehicle is designed to operate on unleaded gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) (Re- search octane number 91).

CAUTION

c Using a fuel other than that specified could adversely affect the emission control devices and systems, and could also affect warranty coverage. c Under no circumstances should a leaded gasoline be used, since this will damage the three way catalyst.

Reformulated Gasoline Some fuel suppliers are now producing re- formulated gasolines. These gasolines are specially designed to reduce vehicle emis- sions. NISSAN supports efforts towards cleaner air and suggests that you use refor- mulated gasoline when available. Gasoline containing oxygenates Some fuel suppliers sell gasoline containing oxygenates such as ethanol, MTBE and methanol with or without advertising their

presence. Nissan does not recommend the use of fuels of which the oxygenate content and the fuel compatibility for your NISSAN cannot be readily determined. If in doubt, ask your service station manager. If you use oxygenate-blend gasoline, please take the following precautions as the usage of such fuels may cause vehicle perfor- mance problems and/or fuel system dam- age. c The fuel should be unleaded and have an octane rating no lower than that recommended for unleaded gasoline. c If an oxygenate-blend other than a methanol blend is used, it should con- tain no more than 10% oxygenate. (MTBE may, however, be added up to 15%.)

c If a methanol blend is used, it should contain no more than 5% methanol (methyl alcohol, wood alcohol). It should also contain a suitable amount of appropriate cosolvents and corro- sion inhibitors. If not properly formu- lated with appropriate cosolvents and corrosion inhibitors, such methanol blends may cause fuel system dam-

age and/or vehicle performance prob- lems. At this time, sufficient data is not available to ensure that all metha- nol blends are suitable for use in NIS- SAN vehicles.

If any driveability problems such as engine stalling and difficult hot-starting are experi- enced after using oxygenate-blend fuels, immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. Take care not to spill gasoline during refueling. Gasoline containing oxygen- ates can cause paint damage. Aftermarket Fuel Additives NISSAN does not recommend the use of any fuel additives (i.e.: fuel injector cleaner, octane booster, intake valve deposit remov- ers, etc.) which are sold commercially. Many of these additives intended for gum, varnish or deposit removal may contain active solvents or similar ingredients that can be harmful to the fuel system and engine. Octane rating tips In most parts of North America, you should use unleaded gasoline with an octane rating Technical and consumer information 10-3

Z X

your

have

encountered,

vehicle are checked at an authorized NISSAN dealer or other competent service facility. However, now and then you may notice light spark knock for a short time while accelerating or driving up hills. This is no cause for concern, because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load.

heavy

‘‘spark

of at least 87 AKI (Anti-Knock Index) num- ber. However, you may use unleaded gaso- line with an octane rating as low as 85 AKI (Anti-Knock Index) number in high altitude areas [over 4,000 ft (1,219 m)] such as: Colorado, Montana, New Mexico, Utah, Wyoming, northeastern Nevada, southern Idaho, western South Dakota, western Ne- braska, and the part of Texas which is directly south of New Mexico. Using unleaded gasoline with an octane rating lower than stated above can cause persistent, knock.’’ (‘‘Spark knock’’ is a metallic rapping noise.) If severe, this can lead to engine damage. If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating, or if you hear steady spark knock while holding a steady speed on level roads, have an authorized dealer correct the condition. Failure to correct the condition is misuse of the vehicle, for which NISSAN is not responsible. Incorrect ignition timing may result in spark knock, after-run or overheating, which may cause excessive fuel consumption or en- gine damage. If any of the above symptoms 10-4 Technical and consumer information

Z X

be found. An ILSAC grade GF-II oil can also be used. Mineral based or synthetic type oils may be used in your NISSAN vehicle. These oils must however, meet the API quality and SAE viscosity ratings specified for your ve- hicle. Do not mix mineral based and syn- thetic type oils in the engine. Oil additives NISSAN does not recommend the use of oil additives. The use of an oil additive is not necessary when the proper oil type is used and maintenance intervals are followed. Oil which may contain foreign matter or has been previously used should not be used. Oil viscosity The engine oil viscosity or thickness changes with temperature. Because of this, it is important that the engine oil viscosity be selected based on the temperatures at which the vehicle will be operated before the next oil change. The chart ‘‘Recom- mended SAE viscosity number’’ shows the recommended oil viscosities for the ex- pected ambient temperatures. Choosing an oil viscosity other than that recommended could cause serious engine damage.

ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil

It is essential to choose engine oil with the correct quality and viscosity oil to ensure satisfactory engine life and performance. NISSAN recommends the use of a low friction oil (energy conserving oil) in order to improve fuel economy and conserve en- ergy. Oils which do not have the specified quality label should not be used as they could cause engine damage.

ATI0645

Only those engine oils with the American Petroleum Institute (API) CERTIFICATION MARK on the front of the container should be used. This type of oil supersedes the existing API SG, SH, or SJ and Energy Conserving II categories. If you cannot find engine oil with the API CERTIFICATION MARK, use an API grade SG/SH, Energy Conserving II or API grade SJ, Energy Conserving oil. An oil with a single designation SG or SH, or in combina- tion with other categories (for example, SG/CC or SG/CD) may also be used if one with the API CERTIFICATION MARK cannot

Technical and consumer information 10-5

Z X

— driving in dusty conditions, — extensive idling, — towing a trailer.

RECOMMENDED SAE VISCOSITY NUMBER

Selecting the correct oil filter Your new NISSAN vehicle is equipped with a high- quality genuine NISSAN oil filter. When replacing, use a genuine NISSAN oil filter or its equivalent for the reason de- scribed in ‘‘Change intervals’’. Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters. Oil and filter other than the specified quality, or oil and filter change intervals longer than recommended could reduce engine life. Damage to the engine caused by improper maintenance or use of incorrect oil and filter quality and/or viscosity is not covered by the new NISSAN vehicle warranties. Your engine was filled with a high quality engine oil when it was built. You do not have to change the oil before the first recom- mended change interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes: — repeated short distance driving at cold

outside temperatures,

10-6 Technical and consumer information

ATI0646

c SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 vis- cosity oil may be used if the ambient temperature is above 0°F (-18°C).

Z X

AIR CONDITIONER SYSTEM REFRIGERANT AND LUBRICANT RECOMMENDATIONS The air conditioner system in this NIS- SAN vehicle must be charged with the refrigerant HFC-134a (R-134a) and the lubricant, NISSAN A/C system oil Type R or the exact equivalents.

CAUTION

Use of any other refrigerant or lubricant will cause severe damage and you will need to replace your vehicle’s entire air conditioner system.

The refrigerant HFC-134a (R-134a) in your NISSAN vehicle does not harm the earth’s ozone layer. Although this refrigerant does not affect the earth’s atmosphere, certain government regulations require the recov- ery and recycling of any refrigerant during automotive air conditioner system service. An authorized NISSAN dealer has the trained technicians and equipment needed to recover and recycle your air conditioner system refrigerant. Contact an authorized NISSAN dealer when servicing your air conditioner system.

Technical and consumer information 10-7

Z X

ENGINE

Model

Type

KA24DE

Gasoline, 4-cycle, DOHC

Cylinder arrangement

4-cylinder, in-line

The spark ignition system of this ve- hicle meets all requirements of the Canadian Interference - Causing Equipment Regulations.

Bore x Stroke

Displacement

Firing order

Idle speed

M/T

A/T (in ‘‘N’’ position)

Ignition timing (degree B.T.D.C. at idle speed)

CO % at idle

Spark plug

Camshaft operation

Generator belt size

in (mm) 3.504 x 3.780 (89.0 x 96.0)

cu in (cm3) 145.7 (2,389)

1-3-4-2

rpm

700 6 50

700 6 50

20° 6 2°

Idle mixture screw is preset and sealed at factory

FR5AP-10 (Standard) FR6AP-10 (Cold) FR7AP-10 (Cold)

Timing Chain

Width x Length

in (mm) 0.8409 x 52.56 (21.36 x 1,335)

10-8 Technical and consumer information

Z X

WHEEL/TIRE SIZE

DIMENSIONS AND WEIGHTS

Conventional

T type (Spare)

Road wheel

Steel

XE, GXE

15 x 6JJ

Aluminum

SE, GLE

15 x 6JJ

Offset

in (mm)

Tire size

XE, GXE, GLE

SE

1.77 (45)

P195/65R15
P205/60R15

15 x 4T

15 x 4T

1.57 (40)

T125/70D15

Overall length

Overall width

Overall height

Front tread

Rear tread

Wheelbase

Gross vehicle weight rating

Gross axle weight rating

Front

Rear

Sedan

183.5 (4,660)

69.1 (1,754)

55.9 (1,420)

59.3 (1,505)

58.9 (1,495)

103.1 (2,620)

See the ‘‘F.M.V.S.S. certification label’’ on the driver side, center door pillar.

in (mm)

in (mm)

in (mm)

in (mm)

in (mm)

in (mm)

lb (kg)

lb (kg)

lb (kg)

Technical and consumer information 10-9

Z X

REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY

VEHICLE IDENTIFICATION

if

find out

When planning to travel in another coun- try, you should first the fuel available is suitable for your vehicle’s en- gine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. Therefore, avoid taking your ve- hicle to areas where appropriate fuel is not available. When transferring the registration of your vehicle to another country, state, province or district, it may be necessary to modify the vehicle to meet local laws and regulations. The laws and regulations for motor vehicle emission control and safety standards vary according to the country, state, province or district; therefore, vehicle specifications may differ. When any vehicle is to be taken into another country, state, province or dis- trict and registered, its modifications, transportation, and registration are the responsibility of the user. NISSAN is not responsible for any inconvenience that may result.

ATI1003

ADI1016

VEHICLE IDENTIFICATION NUMBER PLATE The vehicle identification number plate is attached as shown. This number is the identification for your vehicle and is used in the vehicle registration.

VEHICLE IDENTIFICATION NUMBER (Chassis number) The number is stamped as shown.

10-10 Technical and consumer information

Z X

TI1068

ATI1002

ENGINE SERIAL NUMBER The number is stamped on the engine as shown.

F.M.V.S.S. CERTIFICATION LABEL The Federal Motor Vehicle Safety Stan- dards (F.M.V.S.S.) certification label is af- fixed as shown. This label contains valuable vehicle information, such as: Gross Vehicle Weight Ratings (GVWR), Gross Axle Weight Rating (GAWR), month and year of manufacture, Vehicle Identification Number, (VIN), etc. Review it carefully.

Technical and consumer information 10-11

Z X

ADI1015

ADI1013

ADI1014

EMISSION CONTROL INFORMATION LABEL The emission control attached as shown.

information label

TIRE PLACARD The cold tire pressure is shown on the tire placard, affixed to the driver’s door, center pillar.

is

AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label affixed as shown.

is

10-12 Technical and consumer information

Z X

INSTALLING FRONT LICENSE PLATE

Use the following steps to mount the license plate: 1. Make a hole in each plastic finisher at the location mark (small dimple) using a 0.31
in (8 mm) drill. To avoid damaging the threads behind the finisher, apply only light pressure to the drill.

VEHICLE LOADING INFORMATION

WARNING

c It is extremely dangerous to ride in a cargo area inside of a vehicle. In a collision, people riding in these ar- eas are more likely to be seriously injured or killed.

c Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts. c Be sure everyone in your vehicle is in a seat and using a seat belt properly.

Terms It is important to familiarize yourself with the following terms before loading your vehicle:

c Curb Weight (actual weight of your ve- hicle) - vehicle weight including: standard and optional equipment, fluids, emergency tools, and spare tire assembly. This weight does not include passengers and cargo.

c GVW (Gross Vehicle Weight)

- curb weight plus the combined weight of pas- sengers and cargo.

c GVWR (Gross Vehicle Weight Rating) - Technical and consumer information 10-13

ATI1004

2. Mount the license plate bracket using two of the four 8 mm slotted hex head screws. 3. Use the remaining two 8 mm slotted hex head screws to mount the license plate to the license plate bracket.

Z X

maximum total weight (load) limit speci- fied for the vehicle.

c GAWR (Gross Axle Weight Rating) - maximum weight (load) limit specified for the front or rear axle.

Determining Vehicle Load Capacity The load capacity of this vehicle is determined by weight, not by available cargo space. For example, a luggage rack, bike carrier, cartop carrier or similar equipment does not increase load carrying capacity of your vehicle. To determine vehicle load capacity: Vehicle weight can be determined by using a commercial-grade scale, found at places such as a truck stop, gravel quarry, grain elevator, or a scrap metal recycling facility. 1) Determine the curb weight of your vehicle. 2) Compare the curb weight amount to the GVWR specified for your vehicle to de- termine how much more weight your vehicle can carry.

3) After loading (cargo and passengers), re-weigh your vehicle to determine if either GVWR or GAWR for your vehicle is exceeded. If GVWR is exceeded, re- move cargo as necessary. If either the

front or rear GAWR is exceeded, shift the load or remove cargo as necessary.

Loading Tips c The GVW must not exceed GVWR or GAWR as specified on the FMVSS Cer- tification Label.

c Do not load the front and rear axle to the GAWR. Doing so will exceed the GVWR.

WARNING

c Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.

c Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWRs. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could result in loss of control and cause personal injury.

c Overloading can shorten the life of your vehicle. Failures caused by overloading are not covered by your warranty.

10-14 Technical and consumer information

TRAILER TOWING

TI1011M

Your new vehicle was designed to be used primarily to carry passengers and cargo. Remember that towing a trailer will place additional loads on your vehicle’s engine, drive train, steering, braking and other sys- tems. A Nissan Trailer Towing Guide (U.S. only) containing information on trailer towing abil- ity and the special equipment required may be obtained from an authorized NISSAN dealer.

Z X

Maximum load limits Maximum trailer loads: Never allow the total trailer load to exceed 1,000 lb (454 kg). The total trailer load equals trailer weight plus its cargo weight. Towing loads greater than 1,000 lb (454 kg) or using improper towing equipment could adversely affect vehicle handling, braking and performance.

WARNING

Vehicle damage and/or personal injury resulting from improper towing proce- dures is not covered by NISSAN warran- ties. Information on trailer towing and required towing equipment should be ob- tained from dealers who specialize in pro- viding trailers or other towing equipment.

optional equipment. In addition, front or rear gross axle weight must not exceed the gross axle weight rating (GAWR) shown on the F.M.V.S.S. certification label.

TOWING LOAD/SPECIFICATION CHART

MAXIMUM TOWING LOAD

MAXIMUM TONGUE LOAD

UNIT: lb (kg)

1,000 (454)

110 (49)

Trailer hitch Choose a proper hitch for your vehicle and trailer. A genuine NISSAN trailer hitch is available from your NISSAN dealer (Canada only). Make sure the trailer hitch is securely attached to the vehicle, to help avoid personal injury or property damage due to sway caused by crosswinds, rough road surfaces or passing trucks.

CAUTION

c Do not use axle-mounted hitches. c The hitch should not be attached to or affect the operation of the impact- absorbing bumper.

TI1012M

Tongue load: Keep the tongue load between 9 and 11% of the total trailer load. If the tongue load becomes excessive, rearrange cargo to al- low for proper tongue load. Maximum gross vehicle weight/maximum gross axle weight: The gross vehicle weight of the towing vehicle must not exceed the gross vehicle weight rating (GVWR) shown on the F.M.V.S.S. certification label. The gross ve- hicle weight equals the combined weight of the unloaded vehicle, passengers, luggage, hitch, trailer tongue load and any other

Technical and consumer information 10-15

Z X

c Do not modify the vehicle exhaust system, brake system, etc. when the hitch is installed.

c To reduce the possibility of addi- tional damage if your vehicle is struck from the rear, where practical remove the hitch when not in use. Remove receiver when not in use.

c After the hitch is removed, seal the bolt holes to prevent exhaust fumes, water or dust from entering the pas- senger compartment.

c Regularly check that all hitch mount-

ing bolts are securely mounted.

Tire pressures c When towing a trailer, inflate the vehicle tires to the recommended cold tire pres- sure indicated on the tire placard (affixed to the driver’s door, center pillar).

c Trailer tire condition, size, load rating and proper inflation pressure should be in accordance with the trailer and tire manufacturer’s specifications.

Safety chains Always use suitable chains between your vehicle and the trailer. Safety chains should be crossed and should be attached to the hitch, not to the vehicle bumper or axle. Be sure to leave enough slack in the chains to permit turning corners. Trailer lights Trailer lights should comply with federal and/ or local regulations. When wiring the vehicle for towing, connect the stop and tail light pickup into the vehicle electrical circuit. Trailer brakes If your trailer is equipped with a braking system, make sure it conforms to Federal and/or local regulations and that it is prop- erly installed.

WARNING

Never connect a trailer brake system directly to the vehicle brake system.

Pre-towing tips c Be certain your vehicle maintains a level position when a loaded and/or unloaded trailer is hitched. Do not drive the vehicle if

it has an abnormal nose-up or nose- down condition; check for improper tongue load, overload, worn suspension or other pos- sible causes of either condition.

c Always secure items in the trailer to

prevent load shift while driving.

c Be certain your rear view mirrors conform to all federal, state or local regulations. If not, install any mirrors required for towing before driving the vehicle.

Trailer towing tips In order to gain skill and an understanding of the vehicle’s behavior, you should prac- tice turning, stopping and backing up in an area which is free from traffic. Steering stability and braking performance will be somewhat different than under normal driv- ing conditions. c Always secure items in the trailer to

prevent load shift while driving.

c Avoid abrupt starts, acceleration or

stops.

c Avoid sharp turns or lane changes. c Always drive your vehicle at a moderate

speed.

10-16 Technical and consumer information

Z X

c To maintain engine braking efficiency and electrical charging performance, do not use fifth gear (manual transmission) or overdrive (automatic transmission).

c Avoid holding the brake pedal down too long or too frequently. This could cause the brakes to overheat, resulting in re- duced braking efficiency.

When towing a trailer, change the trans- mission fluid more frequently. For addi- tional information see the ‘‘Mainte- nance’’ section earlier in this manual.

c Always block the wheels on both vehicle and trailer when parking. Parking on a slope is not recommended; however, if you must do so, and if your vehicle is equipped with an automatic transmis- sion, first block the wheels and apply the parking brake, and then move the shift lever into the P position. If you move the shift lever to the P position before block- ing the wheels and applying the parking brake, transmission damage could occur. c When going down a hill, shift into a lower gear and use the engine braking effect. When ascending a long grade, downshift the transmission to a lower gear and reduce speed to reduce chances of en- gine overloading and/or overheating.

c If

the engine coolant rises to an ex- tremely high temperature when the air conditioner system is on, turn off the air conditioner. Coolant heat can be addi- tionally vented by opening the windows, to high and switching the fan control setting the temperature control to the HOT position.

c Trailer towing requires more fuel

than

normal circumstances.

c Avoid towing a trailer for the first 500

miles (800 km).

c Have your vehicle serviced more often than at intervals specified in the recom- mended Maintenance Schedule.

c When making a turn, your trailer wheels will be closer to the inside of the turn than your vehicle wheels. To compensate for this, make a larger than normal turning radius during the turn.

c Crosswinds and rough roads will ad- versely affect vehicle/trailer handling, possibly causing vehicle sway. When being passed by larger vehicles, be pre- pared for possible changes in crosswinds that could affect vehicle handling. If swaying does occur, firmly grip the steer- ing wheel, steer straight ahead, and im- mediately (but gradually) reduce vehicle speed. This combination will help stabi- lize the vehicle. Never increase speed.

c Be careful when passing other vehicles. Passing while towing a trailer requires considerably more distance than normal passing. Remember the length of the trailer must also pass the other vehicle before you can safely change lanes.

Technical and consumer information 10-17

Z X

UNIFORM TIRE QUALITY GRADING

DOT (Department of Transportation) Qual- ity Grades: All passenger car tires must conform to federal safety requirements in addition to these grades. Treadwear Treadwear grade is a comparative rating based on tire wear rate when tested under controlled conditions on specified govern- ment test courses. For example, a tire graded 150 would wear one and a half (1-1/2) times as well on the government course as a tire graded 100. However, relative tire performance depends on actual driving conditions, and may vary signifi- cantly due to variations in driving habits, service practices and differences in road characteristics and climate. Traction AA, A, B and C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades repre- sent the tire’s ability to stop on wet pave- ment as measured under controlled condi- tions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

WARNING

The traction grade assigned to your ve- hicle’s tires is based on straight-ahead braking traction tests and does not in- clude acceleration, cornering, hydro- planing, or peak traction characteristics.

Temperature A, B and C Temperature grades are A (the highest), B, and C. They represent a tire’s resistance to heat build-up, and its ability to dissipate heat when tested under controlled condi- tions on a specified indoor laboratory test wheel. Sustained high temperature can cause tire material to degenerate, reducing tire life. Excessive temperatures can lead to sudden tire failure. Grade C corresponds to a performance level which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades A and B represent higher levels of perfor- mance on laboratory test wheels than the minimum required by law.

WARNING

The temperature grade for this tire is established for a tire that is properly

10-18 Technical and consumer information

inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combi- nation, can cause heat buildup and possible tire failure.

Z X

EMISSION CONTROL SYSTEM WARRANTY

REPORTING SAFETY DEFECTS (USA)

Your NISSAN vehicle is covered by the following emission warranties: For USA 1) Emission Defects Warranty 2) Emissions Performance Warranty For Canada Emission Control System Warranty Details of these warranties may be found with other vehicle warranties in your war- ranty information booklet that comes with your NISSAN vehicle. If you did not receive a warranty booklet, or it is lost, you may obtain a replacement by writing to: c Nissan North America, Inc.

Consumer Affairs Department P.O. Box 191
Gardena, CA 90248-0191

c Nissan Canada Inc. 5290 Orbitor Drive Mississauga, Ontario, L4W 4Z5

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to no- tifying NISSAN. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot be- come involved in individual problems be- tween you, your dealer, or NISSAN. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424- 9393 (or 366-0123 in Washington, D.C. area) or write to: NHTSA, U.S. Depart- ment of Transportation, Washington, D.C. 20590. You can also obtain other informa- tion about motor vehicle safety from the Hotline. You may notify NISSAN by contacting our Consumer Affairs Department, toll-free, at 1-800-NISSAN-1. In Hawaii call (808) 836-0888.

Technical and consumer information 10-19

Z X

READINESS FOR INSPECTION/MAINTENANCE (I/M) TEST (US only) Due to legal requirements in some states and Canadian Provinces, your vehicle may be required to be in what is called the ‘‘ready condition’’ for an Inspection/Maintenance (I/M) test of the emission control system. The vehicle is set to the ‘‘ready condition’’ when it is driven through certain driving patterns. Usually, the ready condition can be obtained by ordinary usage of the vehicle. If a powertrain system component is repaired or the battery is disconnected, the vehicle may be reset to a ‘‘not ready’’ condition. Before taking the I/M test, drive the vehicle through the following pattern to set the ve- hicle to the ready condition. If you cannot or do not want to perform the driving pattern, a NISSAN dealer can conduct it for you.

WARNING

Always drive the vehicle in a safe man- ner according to traffic conditions and obey all traffic laws.

2. Accelerate the vehicle to 55 mph (88
km/h), then quickly release the accelera- tor pedal completely and keep it released for at least 6 seconds.

3. Quickly depress the accelerator pedal for a moment, then drive the vehicle at a speed of 53 to 60 mph (86 to 96 km/h) for at least 5 minutes.

4. Stop the vehicle. 5. Accelerate the vehicle to 35 mph (55
km/h) and maintain the speed for 20
seconds.

6. Repeat steps four through five at least

three times.

7. Accelerate the vehicle to 55 mph (88
km/h) and maintain the speed for at least 3 minutes.

8. Stop the vehicle and turn the engine off. 9. Repeat steps one through eight at least

one more time.

1. Start the engine when the engine coolant temperature gauge needle points to C. Allow the engine to idle until the gauge needle points between the C and H (nor- mal operating temperature).

If step one through seven is interrupted, repeat the preceding step. Any safe driving mode is acceptable between steps. Do not stop the engine until step seven is com- pleted.

10-20 Technical and consumer information

Z X

A Genuine Nissan Service Manual is the best source of service and repair information for your vehicle. Filled with wiring diagrams, illus- trations and step-by-step diagnostic and ad- justment procedures, this manual is the same one used by the factory trained technicians working at an authorized Nissan dealership. Also available are Genuine NISSAN Owner’s Manuals. For current pricing and availability of a Genu- ine NISSAN Service Manual or a Genuine NISSAN Owner’s Manual, contact: In the USA: See an authorized NISSAN dealer or contact:

Dyment Distribution Services 20770 Westwood Dr. Strongsville OH 44136

In a hurry? Call 1-800-247-5321 and charge your purchase to Visa/Master Card. In Canada: To purchase a copy of a Genuine NISSAN Service Manual or Owner’s Manual please contact your nearest NISSAN Dealer. For the phone number and location of a NISSAN Dealer in your area call the Nissan Satisfaction Center at 1-800-387-0122 and a bilingual NIS- SAN representative will assist you. Also available are Genuine NISSAN Service and Owner’s Manuals for older Nissan models. Technical and consumer information 10-21

Z X

MEMO

10-22 Technical and consumer information

Z X

11 Index

Air bag (See supplemental restraint system) ........................................................ 1-9
Air bag warning light ................. 1-12, 1-14, 2-6
Air cleaner housing filter............................ 8-15
Air conditioner

Air conditioner operation ........................ 4-5
Air conditioner specification label....... 10-12
Air conditioner system refrigerant and lubrication recommendations................ 10-7
Heater and air conditioner controls ........ 4-3
Heater and air conditioner (manual)....... 4-3
Servicing air conditioner ......................... 4-9
Air flow charts .............................................. 4-6
Alarm system (See theft warning) ............... 2-9
Anchor point locations ............................... 1-34
Antenna

Manual .................................................. 4-27
Power.................................................... 4-26
Anti-lock brake system (ABS).................... 5-18
Anti-lock brake warning light ....................... 2-7
Ashtray (See cigarette lighter and ashtray) ...................................................... 2-15
Audio system

AM-FM radio with cassette player........ 4-10
AM-FM radio with cassette player and compact disc player.............................. 4-20

AM-FM radio with compact disc (CD) player .................................................... 4-15

Automatic

Automatic power window switch .......... 2-17
Automatic transmission fluid (ATF) ........ 8-9
Driving with automatic transmission...... 5-5, 5-6
Transmission selector lever lock release .................................................... 5-9

Battery........................................................ 8-13
Battery

Charge warning light .............................. 2-5

Battery Replacement (See multi-remote control system) ............................................ 3-7
Before starting the engine ........................... 5-6
Belts (See drive belts)...................... 10-8, 8-14
Brake

Anti-lock brake system (ABS) .............. 5-18
Brake booster ....................................... 8-19
Brake fluid............................................. 8-11
Brake light (See stop light)................... 8-27
Brake pedal .......................................... 8-18
Brake system........................................ 5-17
Brake warning light................................. 2-6

Brake wear indicators ................... 2-7, 8-19
Parking brake check............................. 8-18
Parking brake operation ....................... 5-12
Break-in schedule ...................................... 5-15
Bulb check/instrument panel ....................... 2-5
Bulb replacement....................................... 8-24

Capacities and recommended fuel/ lubricants.................................................... 10-2
Cargo (See vehicle loading information) .............................................. 10-13
Cassette player (See audio system) ......... 4-10
CB radio or car phone ............................... 4-27
Check engine indicator light (See malfunction indicator light) .................. 2-8
Child restraint with top tether strap ........... 1-33
Child restraints ................................. 1-18, 1-24
Child safety rear door lock .......................... 3-4
Cigarette lighter (accessory) and ashtray ....................................................... 2-15
Cleaning exterior and interior ...................... 7-2
Clutch

Clutch fluid............................................ 8-12
Clutch pedal.......................................... 8-20
Cold weather driving.................................. 5-19

Z X

Controls

Heater and air conditioner controls ........ 4-3

Coolant

Capacities and recommended fuel/ lubricants .............................................. 10-2
Changing engine coolant........................ 8-5
Checking engine coolant level ............... 8-4
Engine coolant temperature gauge ........ 2-4
Corrosion protection .................................... 7-5
Cruise control............................................. 5-13
Cup holder ................................................. 2-16

Daytime running light system (Canada only) ............................................ 2-13
Defogger switch

Rear window defogger switch .............. 2-11
Dimensions and weights............................ 10-9
Door ajar warning light ................................ 2-6
Door locks.................................................... 3-2
Drive belts.................................................. 8-14
Driving

Cold weather driving............................. 5-19
Driving with automatic transmission...... 5-5, 5-6
Driving with manual transmission .................................. 5-10, 5-4
Precautions when starting and driving ... 5-2