2008 Mercedes-benz CL Class Owners Manual

COMAND telephone*

Displaying details of an entry COMAND can also show a shortened entry in its entirety. For entries featuring suben- tries, the detailed view is only available for the subentries and not for the main entry. 왘 Select entry (컄 page 157). 왘 Select “Options” 씮 “Details”.

The detailed view appears.

왘 Closing detailed view: Slide qmr or omp or press n or back button L in the center console (컄 page 84).

Starting to dial the number of an entry 왘 Select entry (컄 page 157). 왘 Press n. or 왘 Press s on the telephone keypad. A list appears if the entry contains sub- entries. 왘 Select desired subentry. 왘 Press n again. or 왘 Press s on the telephone key-

pad.

Assigning a New Entry in the Address Book

i This function is used to create a new entry in the address book and to enter the data (first name, last name and telephone number) manu- ally. 왘 Select “Options” 씮 “New Entry” in the

COMAND phone book list.

왘 Selecting a number category: Select a category, e.g. “Home”.

왘 Selecting a telephone category: Select a category, e.g. “Land Line”.

왘 Confirming selection: Select “Save”. The input menu appears with the data fields.

158

왘 Toggling upper and lower case for the input characters: Select & or (.

왘 Changing language for the input

characters: Select !. 왘 Select desired language. 왘 Changing character set for the input

characters: Select #. Depending on the previous setting, you will change to letters with special char- acters or to numbers with special char- acters.

왘 Displaying special characters as in- put characters: Select ! 씮 “Sym- bols”.

왘 Returning input characters to nor- mal characters: Select ! 씮 the desired language.

왘 Moving cursor in the data field:

Select Y or Z.

Control systems COMAND telephone*

왘 Deleting individual characters:

Select ) and briefly press n. The character to the left of the cursor is deleted.

왘 Deleting an entire entry: Select ) and press and hold n until the entry is deleted.

왘 Saving an entry: Select ?. 왘 Canceling an entry: Select “Back”.

If one of the data fields contains data, a prompt will appear asking whether you want to save the entry. 왘 Select “Yes” or “No”.

The entry will either be saved or not, depending on your selection.

159

1 Data field 2 Input mark (cursor) 3 Input characters 왘 Changing data field: Slide qmr re-

peatedly until desired data field is high- lighted.

or 왘 Select [ or ] repeatedly until de-

sired data field is highlighted.

왘 Entering data into a field: Select all characters one by one from the input characters line 3.

Control systems COMAND telephone*

Deleting an entry

i It is not possible to delete a phone book en- try from the mobile phone using the COMAND phone book.

The deletion rules may vary, depending on the entry selected: 앫 Upper entry selected from the address

book: the entry is deleted from the COMAND phone book and also from the address book, if the address book entry only contains telephone numbers.

앫 Subentry of an address book entry se-

lected: the subentry is deleted from the COMAND phone book and from the ad- dress book.

160

왘 Deleting: Select entry (컄 page 157). 왘 Select “Options” 씮 “Delete”.

A prompt appears asking whether the entry should be deleted.

왘 Select “Yes” or “No”.

Once “Yes” has been selected, the en- try will be deleted according to the rules mentioned above.

Saving a phone book entry from the mobile phone in the address book

i This function is used to save an existing phone book entry from the mobile phone in the address book. The following options are avail- able: 앫 Saving as a new address book entry 앫 Adding a telephone number to an existing

address book entry

Saving as a new address book entry 왘 Select phone book entry from mobile

phone (컄 page 157).

i All entries with the following category sym- bols are phone book entries in the mobile phone. 앫 앫 앫 앫 앫 앫

= symbol for “Mobile” category = symbol for “Home” category = symbol for “Work” category = symbol for “Fax” category = symbol for “Pager” category = symbol for “Main” category

왘 Select “Options” 씮 “Save” 씮 “New En-

try”.

왘 Selecting a number category: Select a category, e.g. “Home”.

왘 Selecting a telephone category: Select a category, e.g. “Land Line”.

왘 Confirming selection: Select “Save”. The input menu appears with the data fields. The data field for the telephone number is filled in automatically. The data field for the last name is also filled when the entry to be saved contains a name.

1 Data field 2 Input mark (cursor) 3 Input characters 왘 Proceed as described in the “Changing data field” paragraph in the “Assigning a New Entry in the Address Book” sec- tion (컄 page 158).

Adding a telephone number to an exist- ing address book entry 왘 Select phone book entry from mobile

phone (컄 page 157).

i All entries with the following category sym- bols are phone book entries in the mobile phone. 앫 앫 앫 앫 앫 앫

= symbol for “Mobile” category = symbol for “Home” category = symbol for “Work” category = symbol for “Fax” category = symbol for “Pager” category = symbol for “Main” category

왘 Select “Options” 씮 “Save” 씮 “Add”. 왘 Selecting a number category: Select a category, e.g. “Home”.

왘 Selecting a telephone category: Select a category, e.g. “Land Line”.

왘 Confirming selection: Select “Save”. The search menu for address book en- tries appears.

Control systems COMAND telephone*

왘 Search for desired entry using smart

speller function.

i There is a detailed description of how to search for an address book entry in the “Search- ing for an address book entry” section (컄 page 166). 왘 After selecting an entry, press n.

If there are fewer than four numbers assigned to the selected entry in the selected number category, COMAND will save the data. If four numbers are saved for the se- lected entry, a prompt will appear ask- ing whether you want to overwrite one of the existing numbers.

왘 Select “Yes” or “No”.

If you select “Yes”, a selection list will appear containing the four existing numbers.

컄컄

161

Control systems COMAND telephone*

컄컄

왘 Select number to be overwritten.

COMAND overwrites the selected num- ber with the new data.

Adding a telephone number to an address book entry

i This function is used to add a telephone number to an existing address book entry. The telephone number can be entered manually. 왘 Select address book entry

(컄 page 157).

i All entries with the symbol are address book entries. 왘 Select “Options” 씮 “Add Number”.

symbol or without a

i “Add Number” does not function if you have selected the main entry for an address book en- try with subentries.

왘 Selecting a number category: Select a category, e.g. “Home”.

왘 Selecting a telephone category: Select a category, e.g. “Land Line”.

왘 Confirming selection: Select “Save”. If four numbers are saved for the entry in the selected number category, a prompt will appear asking whether one of the existing numbers should be over- written. 왘 Select “Yes” or “No”.

If you select “Yes”, a selection list will appear containing the four ex- isting numbers.

왘 Select number to be overwritten. The input menu appears with the data field for entering the new tele- phone number.

왘 Entering digits: Select all digits one

by one from the input characters. 왘 Moving cursor in the data field:

Select Y or Z.

왘 Deleting individual digits: Select )

and briefly press n. The digit to the left of the cursor is de- leted.

왘 Deleting an entire number:

Select ) and press and hold n until the number is deleted.

왘 Saving entry: Select ?. 왘 Canceling an entry: Select “Back”. If you have already entered data, a prompt will appear asking whether the entry should be saved. 왘 Select “Yes” or “No”.

The entry will either be saved or not, depending on your selection.

162

COMAND address book

Warning!

Please devote your attention first and fore- most to the traffic situation you are in.

Before your journey, please familiarize your- self with the address book functions.

Only use the COMAND when road and traffic conditions permit you to do so. Otherwise you could be involved in an accident in which you or others could be injured.

General notes The address book contains the entries that are saved in the COMAND address book memory. The entries are permanently available even if the phone is not inserted in the cradle*. When you insert the mobile phone into the cradle*, COMAND reads-in the phone book entries saved in the mobile phone and stores the entries as a separate list from the COMAND address book. This list is a copy of the phone’s phone book. This can take several minutes, depending on how many entries the phone book and the address book contain. After the read-in process, the COMAND compares the phone book entries with the address book entries. If all of the telephone numbers of a phone book entry in the mobile phone are present in an address book entry, the ad- dress book shows only the address book entry. If not, the address book also shows the phone book entry in the mobile phone.

Control systems COMAND telephone*

Address book menu overview

i The components and operating principles of COMAND can be found on (컄 page 83).

Search Search for an ad- dress book entry

New Entry Create new address book entry

163

Control systems COMAND telephone*

Calling up the address book 왘 Select “Telephone” 씮 “Data/Connec-

tions” 씮 “Address Book”. The main address book display ap- pears.

Selecting an entry in the main address book display 왘 Slide qm to select the main area. 왘 Slide qmr or rotate ymz to select an

entry.

or 왘 Searching for an entry with the smart

speller (컄 page 166).

Illustration: address book entries i For phone book entries in the mobile phone that contain a name and a telephone number, you will see the name and the number. If a phone book entry in the mobile phone contains several telephone numbers, you will see the message “Multiple Numbers” instead of a telephone num- ber.

164

Creating a new address book entry

i Please observe the following when creating a new address book entry: You can define your own address in the destina- tion memory in navigation mode. When defining the address, you can transfer data already en- tered as an address book entry. In the address book entry, the city and street must be spelled in the same way as the destina- tion entry so that the data matches the digital map data. In order for the state (province) to match the map data, its complete name or abbreviation may be entered. Examples: 앫 Florida or FL 앫 Colorado or CO 앫 Alberta or AB 앫 Ontario or ON 왘 Select “Telephone” 씮 “Data/Connec-

tions” 씮 “Address Book” 씮 “Options”씮“New Entry”. The input menu appears with the data fields and the input characters.

왘 Switching between private and business data: Select symbol 1. The display switches to private or busi- ness data, depending on the previous status.

왘 Changing data field: Slide rmq re-

peatedly until desired entry is highlight- ed.

or 왘 Select [ or ] repeatedly until de-

sired entry is highlighted.

왘 Entering data into a field:

Select desired characters one by one from the input characters.

왘 Toggling upper and lower case for the input characters: Select & or (.

왘 Changing language for the input

characters: Select !. 왘 Select desired language.

Control systems COMAND telephone*

왘 Changing character set for the input

characters: Select #. Depending on the previous setting, you will change to letters with special char- acters or to numbers with special char- acters.

왘 Moving cursor in the data field:

Select Y or Z.

왘 Deleting individual characters:

Select ) and briefly press n. The character to the left of the cursor is deleted.

왘 Deleting an entire entry: Select ) and press and hold n until the entry is deleted.

왘 Saving an entry: Select ?.

컄컄

165

Illustration: input menu for private data 1 To switch between work and home

data (

or

symbol)

2 Selected data field with input mark

(cursor)

3 Display of set data type – in example symbol

display, home data is set ( and “Home” display)

4 Input characters

Control systems COMAND telephone*

컄컄

왘 Canceling an entry: Select “Back”.

If one of the data fields contains new data, a prompt will appear asking whether you want to save the entry. 왘 Select “Yes” or “No”.

The entry will either be saved or not, depending on your selection.

Searching for an address book entry 왘 Select “Telephone” 씮 “Data/Connec-

tions” 씮 “Address Book”. The search menu appears with the smart speller.

1 Symbol

for complete address data

from the navigation system

2 Symbol

for summarized entries

from the mobile phone with the same name but different telephone numbers

3 Category symbol 4 Smart speller 5 Symbol 6 Back to the main address book display

for voice entry

166

Entries with category symbol 3 come from the mobile phone. The following cate- gory symbols are possible: 앫

= symbol for “Mobile” category = symbol for “Home” category = symbol for “Work” category = symbol for “Fax” category = symbol for “Pager” category = symbol for “Main” category or for unknown category or for phone entries that are saved on the SIM card of a GSM mobile phone

앫

앫

앫

앫

앫

or

symbols come from the

Entries without a category symbol or with the COMAND address book. All other entries come from the mobile phone and are only visible when the mobile phone is in the cra- dle*. It is possible to add voice entries. Entries with the symbol contain a voice entry (컄 page 173).

Entries with the symbol contain com- plete, navigable address data from the nav- igation system that correspond to digital map data. It is possible to quickly start route guidance to these types of entry (컄 page 172).

Switching from the smart speller to the list 왘 Slide mq repeatedly or press n until

the smart speller is hidden.

or 왘 Select ?.

Switching from the list to the smart speller 왘 Select “Back” from the list.

Searching via the smart speller 왘 Switch from the list to the smart speller

if necessary.

왘 Changing smart speller language:

Select !.

왘 Select desired language. 왘 Changing smart speller character

set: Select #. Depending on the previous setting, you will change to letters with special char- acters or to numbers with special char- acters.

왘 Entering characters: Select the char- acters one by one of the entry you are searching for.

왘 Deleting individual characters:

Select ) and briefly press n. Each time you enter or delete a charac- ter, the closest match will be displayed at the top of the list.

Control systems COMAND telephone*

왘 Deleting an entire entry: Select ) and press and hold n until the entry is deleted.

왘 Canceling search: Switch from the smart speller to the list (컄 page 167). The entry at the top of the list is auto- matically highlighted.

왘 Going back to main address book

display: If necessary, switch from the list to the smart speller (컄 page 167) and select “Back” in the smart speller.

Searching via the list 왘 If necessary, switch from the smart

speller to the list (컄 page 167).

왘 Rotate ymz or slide qmr until desired

entry is highlighted on the list.

167

Control systems COMAND telephone*

Displaying a complete address book entry

Searching for the desired entry 왘 Search for an address book entry

(컄 page 166).

or 왘 Select an address book entry in the

main address book menu (컄 page 164).

왘 Press n.

The detailed view appears.

168

i The options available under “Options” menu item 5 depend on which data field 3 is select- ed. The following options may be available: 앫 Displaying abbreviated content in full

(컄 page 169)

앫 Changing an address book entry

(컄 page 170)

앫 Changing the description of a telephone

number data field (컄 page 170)

앫 Adding a telephone number data field

(컄 page 171)

앫 Calling a number saved in an entry

(컄 page 172)

앫 Starting route guidance to an entry

(컄 page 172)

앫 Options for voice entries (컄 page 173)

Illustration: detailed view for private data 1 To go back to the previous menu 2 To switch between work and home

data (

symbol or

3 Selected data field 4 Display of set data type – in example symbol

display, home data is set ( and “Home” display)

5 To call up options

Displaying of a complete phone book entry in the mobile phone

i The mobile phone must be inserted in the cradle*.

Searching for the desired entry 왘 Search for a phone book entry in the

mobile phone (컄 page 166).

왘 Press n.

The detailed view appears.

Switching between private or business data 왘 Select symbol 2.

The display switches to private or busi- ness data, depending on the previous status.

Selecting a different data field 왘 Rotate ymz or slide qmr.

Displaying abbreviated content in full 왘 Select “Options” 씮 “Details”.

The display is shown in full.

왘 Closing entire display: Slide omp or

press n.

Closing the detailed view 왘 Select “Back”.

Control systems COMAND telephone*

1 To go back to the previous menu 2 Category symbol 3 Display for phone book entry in mobile

phone

4 To call up options

i If a phone book entry in the mobile phone has more than one telephone number, you will see all telephone numbers with the respective category symbol 2 in the detailed view.

169

Control systems COMAND telephone*

i The options available under “Options” menu item 4 depend on which data field 3 is select- ed. The following options may be available: 앫 Calling a number saved in an entry

((컄 page 172)

앫 Saving a phone book entry from mobile phone in the address book (컄 page 175)

Closing the detailed view 왘 Select “Back”.

170

Changing an entry

Changing an address book entry 왘 Search for an address book entry

(컄 page 166).

or 왘 Display the details of an address book

entry (컄 page 168). The input menu appears with the data fields.

왘 Select “Options” 씮 “Change”. 왘 Proceed as described in the “Switching

between private and business data” paragraph in the “Creating a new ad- dress book entry” section (컄 page 164).

Changing the description of a telephone number data field

i This function is not possible for phone book entries in the mobile phone. 왘 Display the details of an entry and high- light the telephone number data field (컄 page 168).

왘 Select “Options” 씮 “Change Catego-

ry”.

왘 Select a number category, e.g. “Home”. 왘 Select a telephone category, e.g. “Land

Line”.

왘 Select “Save”.

COMAND saves the data if there are fewer than four numbers assigned to the entry you are searching for in the selected number category. Otherwise, you will see a prompt ask- ing whether one of the existing num- bers should be overwritten.

왘 Select “Yes” or “No”.

If you select “Yes”, a selection list will appear containing the four existing numbers.

왘 Select number to be overwritten.

COMAND overwrites the selected num- ber with the new data.

Adding to a telephone number data field

i One address book entry may contain up to four data fields for private telephone numbers and four data fields for business telephone num- bers. This function is not possible for phone book en- tries in the mobile phone. 왘 Display the details of an entry and high- light the telephone number data field (컄 page 168).

왘 Select “Options” 씮 “Add Number”. 왘 Select a number category, e.g. “Home”. 왘 Select a telephone category, e.g. “Land

Line”.

왘 Select “Save”.

COMAND adds the data field to the entry if there are fewer than four numbers as- signed to the entry in the selected number category. You can now enter a number into the data field. 왘 Proceed as described from the “Enter- ing data into a field” operating step in the “Creating a new address book en- try” section (컄 page 164).

If four numbers are already saved for the entry in the selected number category, a prompt will appear asking whether one of the data fields should be overwritten. 왘 Select “Yes” or “No”.

If you select “Yes”, a selection list will appear containing the four data fields.

왘 Select field to be overwritten.

COMAND deletes the number of the se- lected field. You can now enter a new number into the data field.

Control systems COMAND telephone*

왘 Proceed as described from the “Enter- ing data into a field” operating step in the “Creating a new address book en- try” section (컄 page 164).

Deleting an entry

i You cannot delete phone book entries from the mobile phone. 왘 Search for desired entry (컄 page 166). 왘 Select “Options” 씮 “Delete”.

A deletion prompt appears.

왘 Select “Yes” or “No”.

The entry will either be deleted or not, depending on your selection.

171

Control systems COMAND telephone*

Calling a number saved in an entry

i To do this, COMAND must be equipped with a telephone*. The mobile phone must be insert- ed in the cradle*. 왘 Display the details of an entry and high- light the telephone number data field (컄 page 168).

왘 Press n and select “Call”. or 왘 Select “Options” 씮 “Call”.

In both cases, the telephone* connects the call. The COMAND display is show- ing the telephone mode screen.

172

Starting route guidance to an entry 왘 Search for an address book entry

(컄 page 166).

왘 Display the details of an entry and high-

Address data is complete and matches digital map If “Navigate” is selected, the navigation system starts the route calculation.

light the address data field (컄 page 168).

왘 Select “Options” 씮 “Navigate”. or 왘 Press n.

i Pressing n only functions if one of the ad- dress data fields contains data.

Further operation depends on whether the address data is complete and matches the digital map data of the navigation system. It does not match, for example, if it is not spelled in the same way as the destination entry.

Address data is incomplete or does not match digital map

i For the route calculation, the navigation sys- tem requires the correct spellings of the state (province), the city or zip code, the street and un- der some circumstances, the house number. The city and street must be spelled in the same man- ner as the destination entry. The state (province) can be spelled as an entire name or as an abbreviation. Examples: 앫 Florida or FL 앫 Colorado or CO 앫 Alberta or AB 앫 Ontario or ON

Control systems COMAND telephone*

왘 Entering a street: Proceed as de-

scribed for destination entry in the “En- tering a street” section (컄 page 207). 왘 Entering a house number: Proceed as described for destination entry in the “Entering a house number” section (컄 page 212).

i If you have added data, COMAND saves your additions. This means that you do not need to re-enter this additional data later on. The COMAND memory saves the additional data in a special field, which cannot be displayed. The data, which you have entered in the address book initially in the display, remains unchanged.

If all data is available and matches the dig- ital map data, the navigation system starts the route calculation.

Voice entries

i For voice entries, your vehicle must be equipped with Voice Control. You can not add voice entries to address book entries that have been read-in from the phone book of the mobile phone.

Adding or changing a voice entry

i You can add one voice entry per address book entry. 왘 Search for the address book entry with or without a voice entry (컄 page 166). 왘 Select “Options” 씮 “Voice Name” 씮

“Add” or “Change”. Subsequent operation is controlled by voice. Voice Control guides you through the dialogs.

If “Navigate” is selected, a message ap- pears indicating that the address is incom- plete. 왘 Closing message: Select “OK”. Depending on which data is missing or cannot be found on the digital map, you must now either: 앫 select a state (province) 앫 select a county 앫 or enter a city 앫 or enter a street 앫 or enter a house number 왘 Selecting a state (province):

Select desired state (province) from the list.

왘 Selecting a county: Select desired

county from the list.

왘 Entering a city: Proceed as described for destination entry in the “Entering a city” section (컄 page 204).

173

Control systems COMAND telephone*

Deleting a voice entry 왘 Search for the address book entry with

a voice entry (컄 page 166).

왘 Select “Options” 씮 “Voice Name” 씮

“Delete”. A deletion prompt appears.

왘 Select “Yes” or “No”.

COMAND deletes the voice entry de- pending on your selection.

Listening to a voice entry 왘 Search for the address book entry with

a voice entry (컄 page 166).

왘 Select “Options” 씮 “Voice Name” 씮

“Read Aloud”. You will hear the voice entry.

174

Saving a phone book entry from mobile phone in the COMAND address book

Saving a phone book entry from mobile phone as new address book entry

i The mobile phone must be inserted in the cradle* and the COMAND have read out the mo- bile phone book data. This can take several min- utes, depending on how many entries each phone book contains. 왘 Search for phone book entry in mobile

phone (컄 page 166).

or 왘 Display details of a phone book entry in

the mobile phone (컄 page 158).

왘 Select “Options” 씮 “Save” 씮 “New En-

try”.

왘 Select a number category, e.g. “Work”. 왘 Select a telephone category,

e.g. “Mobile”.

왘 Select “Save”.

The input menu appears with the data fields. The name and the telephone number are entered automatically.

1 Data field 2 Input mark (cursor) 3 Input characters 왘 Proceed as described in the “Changing a data field” paragraph in the “Creating a new address book entry” section (컄 page 164).

Saving a phone book entry from the mo- bile phone in an existing address book entry

i The mobile phone must be inserted in the cradle*. 왘 Search for a phone book entry in the

mobile phone (컄 page 166).

or 왘 Display details of a phone book entry in

the mobile phone (컄 page 168).

왘 Select “Options” 씮 “Save” 씮 “Add”. 왘 Select a number category, e.g. “Home”. 왘 Select a telephone category, e.g. “Land

Line”.

왘 Select “Save”.

The search menu for address book en- tries appears.

왘 Search for desired entry.

i There is a detailed description of how to search for an address book entry in the “Search- ing for an address book entry” section (컄 page 166). 왘 After selecting an entry, press n.

COMAND saves the data if there are fewer than four numbers assigned to the selected entry in the selected num- ber category. Otherwise, you will see a prompt asking whether one of the ex- isting numbers should be overwritten.

왘 Select “Yes” or “No”.

If you select “Yes”, a selection list will appear containing the four existing numbers.

왘 Select the number to be overwritten.

COMAND overwrites the selected num- ber with the new data.

Control systems COMAND telephone*

Importing data from external Bluetooth® devices You can import vCards from external Bluetooth® devices into the address book. Please keep the following in mind: 앫 Bluetooth® is activated in COMAND (컄 page 176) and in the device con- cerned.

앫 The external device must be able to

send vCards by Bluetooth®.

앫 The external device is inside the vehi-

cle, switched on and authorized (컄 page 176).

175

Control systems COMAND telephone*

왘 Importing: Start data transfer on the external device (see operating instruc- tions of the device concerned). If there is no address book entry with the same first name and last name, COMAND imports the data. If there is already an address book en- try with the same first name and last name, a prompt will appear asking whether the existing data should be overwritten.

왘 Select “Yes” or “No”.

The existing address book entry will be overwritten or not, depending on your selection.

176

Bluetooth® settings

Connecting Bluetooth® devices

General information about Bluetooth® Bluetooth® technology is the standard for short-range wireless technologies, suitable for transmitting voice and data. It is possi- ble to connect Bluetooth® devices wire- lessly. Bluetooth® can be used to exchange vCards or make calls using a headset. Bluetooth® technology uses the freely available ISM (Industrial Scientific Medi- cal) wireless network that works at 2.45 GHz. Ranges of up to ten meters are possible with Bluetooth®.

Activate or deactivate Bluetooth® 왘 Select “Telephone” 씮 “Data/Connec- tions” 씮 “Bluetooth” 씮 “Deactivate Bluetooth”. You have activated or deactivated Bluetooth®. A checkmark appears when Bluetooth® is deactivated.

i To connect a Bluetooth® device, the Bluetooth® function must be activated in COMAND and in the device concerned. The Bluetooth® device must also be set to “visible” or “findable” in order for COMAND to find and display it. For the setting procedures, please see the operating instructions for the Bluetooth® device.

It is possible to establish a Bluetooth® con- nection between COMAND and the follow- ing types of device: 앫 Mobile phone (only for transferring

business cards)

앫 Headset 앫 Laptop/PDA You can connect up to twelve devices to COMAND but only one device can be ac- tive at a time. The connection process includes search- ing for the device and its subsequent au- thorization.

Calling up the Bluetooth® device list and searching for devices 왘 Calling up the list: Select “Telephone” 씮 “Data/Connections” 씮 “Bluetooth” “Search for Bluetooth devices”. When you call up the list for the first time after switching on COMAND, the search for devices in the reception range starts automatically. You will see a display to this effect. The device list appears after a short while. 왘 Canceling search:

Select “Cancel”.

The second time you call up the list, and each time thereafter, the device list ap- pears immediately if COMAND has not been switched off and on again in the meantime. 왘 Starting search manually:

select “Update”.

The device list can contain the following devices: 앫 All detected devices, whether autho-

rized or not.

앫 All authorized devices, whether detect-

ed or not.

1 Authorized and detected device – de-

vice and padlock symbol are the same color

2 Device which was not detected, but

which has been authorized in the past – device and padlock symbol are differ- ent colors (the device may be switched off or not in the vehicle, for example)

3 Newly detected device - not yet autho-

rized (no symbol)

Control systems COMAND telephone*

i If the device list already contains twelve au- thorized devices, you must revoke authorization for one of the authorized devices. Then you must switch this device off and then restart the search. Any new devices for which you would like to search will otherwise not appear in the list.

Displaying details of a Bluetooth® device 왘 Call up the Bluetooth® device list

(컄 page 177).

왘 Select desired device. 왘 Select “Details”.

The detailed display for this device ap- pears.

왘 Closing detailed display: Slide qmr

or ymz.

177

Control systems COMAND telephone*

Authorizing a Bluetooth® device 왘 Call up Bluetooth® device list

(컄 page 177).

왘 Select unauthorized device. 왘 Select “Authorize”.

The input menu for the passkey ap- pears.

i The passkey is any one to sixteen-digit num- ber which you can set yourself. You must enter the same number in COMAND and also in the de- vice to be authorized.

i On devices which do not have an input key- pad (e.g. headsets), the passkey is predeter- mined. In this case, it is not necessary to enter the number on the device itself. You will usually find the passkey in the operating instructions for the device. 왘 Entering passkey into COMAND:

Select the digits one by one.

왘 Deleting digits: Select ) and briefly

press n.

왘 Canceling entry into COMAND:

Select “Back”.

왘 Confirming entry into COMAND:

Select ?.

왘 If necessary, enter the same passkey into the Bluetooth® device (see the op- erating instructions for the device). The device is authorized.

De-authorizing a Bluetooth® device 왘 Call up Bluetooth® device list

(컄 page 177).

왘 Select authorized device. 왘 Select “De-authorize”.

A prompt appears asking whether you really want to de-authorize this device.

왘 Select “Yes” or “No”.

If you select “Yes”, the device will be de-authorized.

i If you de-authorize a device which has been authorized in the past and which is not detected in the search, this device will no longer be dis- played in the device list. Devices which have been authorized in the past but which are not detected in the search are ei- ther not switched on or not in the vehicle.

SMS messages (Short Message Service)

SMS functions The following functions are available: 앫 Receive 앫 Read The following conditions must be fulfilled in order to use the functions: 앫 The mobile phone is inserted in the cra-

dle and switched on.

앫 The PIN has been entered (only GSM

mobile phones).

앫 The mobile phone is logged into a mo-

bile network.

178

앫 Mobile phone book must be download-

ed and available in COMAND.

왘 Select “Text Message”. The SMS inbox appears.

Inbox

Calling up the SMS inbox 왘 Select “Telephone”.

The main telephone menu appears.

i “Text Message” does not function if the SMS inbox contains no SMS messages. The SMS inbox only shows the messages which are re- ceived while the mobile phone is inserted in the cradle.

1 Symbol

for unread messages in the

SMS inbox

i The symbol only appears for those mes- sages which are received while the mobile phone is inserted in the cradle.

1 Date and time the highlighted SMS

message was received

2 To call up options 3 Highlighted SMS message 4 Symbol 5 Back to main telephone menu

for unread SMS message

Control systems COMAND telephone*

i The SMS messages are sorted by the date and time they were received. The most recent message is at the top of the list. If the name and telephone number of the sender is saved in the address book or phone book of the mobile phone, you will see the name of the sender in the SMS inbox. Otherwise, you will see the telephone number of the sender.

Selecting an SMS message 왘 Rotate ymz or slide qmr and then

press n.

Showing abbreviated sender display in full 왘 Select SMS message 씮 “Options” 씮

“Details”. The detailed view appears.

왘 Closing detailed view: Slide qmr or

press n.

179

Control systems COMAND telephone*

Calling an SMS sender 왘 Select SMS message 씮 “Options” 씮

“Call”. The telephone connects the call.

Saving SMS sender as new COMAND address book entry 왘 Selecting an SMS message: In the SMS inbox, select a message 씮 “Op- tions” 씮 “Save Number” 씮 “New En- try”.

왘 Selecting a number category: Select a category, e.g. “Home”.

왘 Selecting a telephone category: Select a category, e.g. “Land Line”.

왘 Saving: Select “Save”.

The input menu appears with the data fields. The data field for the telephone number is filled in automatically.

180

Adding an SMS sender’s telephone num- ber to an existing address book entry 왘 Selecting an SMS message: In the SMS inbox, select a message 씮 “Op- tions” 씮 “Save Number” 씮 “Add”.

왘 Proceed as described in the “Selecting a number category” paragraph in the “Adding a telephone number to an ex- isting address book entry” section (컄 page 161).

Exiting the SMS inbox 왘 Select “Back”.

The main telephone menu appears.

Reading an SMS message 왘 In the SMS inbox, select an SMS mes-

sage and press n. The SMS message appears.

1 Data field 2 Input mark (cursor) 3 Input characters 왘 Proceed as described in the “Changing data field” paragraph in the “Assigning a New Entry in the Address Book” sec- tion (컄 page 158).

Control systems COMAND telephone*

Adding an SMS sender’s telephone num- ber to an existing address book entry 왘 Press n 씮 “Save Number” 씮 “Add”. 왘 Proceed as described in the “Selecting a number category” paragraph in the “Adding a telephone number to an ex- isting address book entry” section (컄 page 161).

Closing an SMS message and returning to SMS inbox 왘 Press n 씮 “Back”.

Calling an SMS sender 왘 Press n 씮 “Call”.

The telephone connects the call.

i This function is not possible with all SMS senders.

Saving SMS sender as new address book entry

i This function is not possible with all SMS senders. 왘 Press n 씮 “Save Number” 씮 “New

Entry”.

왘 Proceed as described in the “Selecting a number category” paragraph in the “Saving SMS sender as new address book entry” section (컄 page 180).

181

Using data in a text message

i If the SMS message contains telephone numbers or navigable address data, you can se- lect this data and place a telephone call or trans- fer the address data to the navigation system. 왘 Selecting data from the text:

Rotate ymz or slide qmr.

왘 Using data: Press n 씮 “Use”.

If you have selected a telephone num- ber, the telephone connects the call. If you have selected a navigable ad- dress, it is transferred to the navigation system.

COMAND may give incorrect navigation commands if the data in the digital map does not correspond with the actual road/traffic situation. DVD maps do not cover all areas nor all routes within an area. For example, if the traffic routing has been changed or the direction of a one-way road has been reversed.

For this reason, you must always observe applicable road and traffic rules and regula- tions during your journey. Road and traffic rules and regulations always have priority over the navigation commands generated by the system.

Warning!

Navigation announcements are intended to direct you while driving without diverting your attention from the road and driving.

Please always use this feature instead of consulting the map display for directions. Consulting the symbols or map display for directions may cause you to divert your at- tention from driving and increase your risk of an accident.

Control systems COMAND navigation

Safety precautions

Warning!

For safety reasons, only enter a destination when the vehicle is stationary. When the ve- hicle is in motion, a passenger should enter the destination. Study manual and select route before driving.

Bear in mind that at a speed of just 30 mph (approximately 50 km/h), your vehicle is covering a distance of 44 feet (approximate- ly 14 m) every second.

COMAND calculates the route to the desti- nation without taking account of the follow- ing, for example: 앫 Traffic lights 앫 Stop and right-of-way signs 앫 Parking or stopping prohibited areas 앫 Lane merging 앫 Other road and traffic rules and regula-

tions

앫 Narrow bridges

182

Control systems COMAND navigation (introduction)

왔 COMAND navigation (introduction) Map software

Updating the map software

The digital maps generated by the map software become outdated in the same way as conventional road maps. Optimum route guidance can only be provided by the navigation system in conjunction with the most up-to-date map software. Information about new map software ver- sions can be obtained from an authorized Mercedes-Benz Center.

You can update the map software yourself using a DVD.

Notes about handling DVDs 앫 Only hold discs by the edge. 앫 Handle discs carefully to prevent read

problems.

앫 Avoid getting scratches, fingerprints

and dust on discs.

앫 Use a commercially-available cleaning cloth to clean discs. Do not wipe them with a circular motion, but only in straight lines from the center out- wards.

앫 Place discs back in their boxes after

use.

앫 Protect discs from heat and direct sun-

light.

Updating process

The updating process has the following phases: 앫 Loading a DVD into the DVD changer

(컄 page 184)

앫 Updating process (컄 page 185)

i The updating process can take between 10 and 60 minutes, depending on the size of the map software. If the radio was switched on be- fore you started the updating process, you can still adjust the volume. You can also use COMAND to operate the automatic air condition- ing and to cancel the process. Other functions are not operational. If possible, carry out the update when the vehicle is stationary.

183

Control systems COMAND navigation (introduction)

i If you carry out the update with the engine switched off and the vehicle battery has insuffi- cient power, COMAND may automatically switch off during the process in order to protect the bat- tery. If this occurs, restart the update with the engine running period. Similarly, if the SmartKey position is unintentionally switched to 0, restart the update.

Warning!

Never leave the engine running in an en- closed space. The exhaust gases contain carbon monoxide. Inhaling exhaust gases constitutes a health hazard and could lead to loss of consciousness or even death.

184

왘 Switch on COMAND (컄 page 83). 왘 Press one of the magazine tray

buttons 2. If a disc is loaded, it will be ejected.

왘 Take disc out of slot 1. 왘 Wait until LED for magazine button 2

which you pressed flashes quickly.

왘 Slide DVD into slot 1 with printed side

facing upwards. COMAND loads the DVD.

Loading a DVD into the DVD changer

1 Disc slot 2 Magazine tray buttons 1 – 6

i Each magazine tray button 2 indicates the status of the corresponding magazine tray by means of an LED. 앫 LED off = magazine tray is empty 앫 LED constantly lit = magazine tray is loaded 앫 LED flashes = CD/DVD changer requesting

disc to be loaded

Control systems COMAND navigation (introduction)

Updating

왘 Select “Yes” or “No”.

After you have loaded the DVD, you will see a message to the effect that the disc does not contain a recognizable audio for- mat. 왘 Confirming message: Press n.

COMAND checks whether the map software on the DVD is compatible with the vehicle’s navigation system and whether it is compatible with the cur- rent system software.

Map software is compatible with the navigation system and the current sys- tem software COMAND now checks whether the map data on the DVD is already installed.

Map data is not yet installed You will see a comparison of the version statuses in the display and a prompt will appear asking whether you want to contin- ue with the update.

If you select “No”, COMAND automati- cally ejects the DVD and the map data is not updated. 왘 Take DVD out of the slot. If you select “Yes”, the map data is up- dated.

Map data is already installed You will see a message that the map data is already installed and a prompt will ap- pear asking you whether you want to con- tinue with the update. 왘 Select “Yes” or “No”.

If you select “No”, COMAND automati- cally ejects the DVD and the map data is not updated. 왘 Take DVD out of slot. If you select “Yes”, the existing map data is saved again.

Updating the map data While the update is running, you will see a message to this effect and a progress bar. The progress bars fills up from left to right during the update.

1 Progress bar You can either cancel the update or allow it to run to the end without canceling. 왘 Canceling an update on the DVD

changer: Press corresponding maga- zine tray button 2 (컄 page 184). The DVD will be ejected in both cases.

왘 Take DVD out of slot.

185

Control systems COMAND navigation (introduction)

i If the update is canceled, the navigation sys- tem remains fully operational with the previous map data. You can restart the update at a later date. It will then continue from the point where it was canceled. 왘 To allow the update to run to the end without canceling: Take no fur- ther action. If the update is successfully complet- ed, you will see a message to this ef- fect.

왘 Confirming message: Press n.

COMAND ejects the DVD.

왘 Take DVD out of slot.

The update is complete.

i The navigation system remains fully opera- tional with the previous map data.

The update may not be successfully com- pleted for the following reasons: 앫 DVD dirty or scratched

왘 Clean DVD.

See the “Notes about handling DVDs” section (컄 page 183).

왘 Restart update.

앫 Overheating due to excessive tempera-

tures in the vehicle interior 왘 Wait until vehicle interior has

cooled down.

왘 Restart update.

If the update is not successfully complet- ed, you will see a message that the map update is not possible. 왘 Confirming message: Press n.

앫 The storage medium (hard disk) inte-

grated in COMAND is defective. 왘 Consult an authorized Mercedes-Benz Center.

COMAND ejects the DVD.

왘 Take DVD out of slot.

186

Map software is not compatible with the navigation system You will see a message that the update is not possible. 왘 Confirming message: Press n.

COMAND ejects the DVD.

왘 Take DVD out of slot. 왘 Load a DVD which is compatible with

the vehicle’s navigation system.

Map software is not compatible with the current system software You will see a message that the system software and the map software are not compatible. 왘 Confirming message: Press n.

COMAND ejects the DVD.

왘 Take DVD out of slot. 왘 Have the system software updated at an authorized Mercedes-Benz Center.

i The map software cannot be updated until the system software has been updated.

Control systems COMAND navigation (introduction)

General notes

Operational readiness of the navigation system following a system software update by an authorized Mercedes-Benz Center After a system software update by an au- thorized Mercedes-Benz Center, the in- stalled map software may no longer be compatible. If this is the case, the naviga- tion system will not be operational. You will know if this is the case, when the following message will appear when you switch to navigation mode: “The system software has been updated. The map soft- ware must be updated now. Please insert the DVD with the map software.” 왘 Updating map software: Proceed as

described in the “Updating the map software” section (컄 page 183). Use map software which is compatible with the system software.

i Please note that the update must be allowed to run to the end in this case. If you interrupt it, the navigation system will continue to be non-op- erational.

Initial use or use following a system software update In both these cases, the navigation system must determine the position of the vehicle. You may have to drive for a while before precise route guidance is possible.

GPS reception Correct functioning of the navigation sys- tem depends on GPS reception, among other things. In certain situations, GPS re- ception may be impaired, there may be in- terference or no reception at all, e.g. in tunnels, in multistory parking garages or there is snow covering the trunk lid where the GPS antenna is located. If there is snow on the trunk lid it should be removed.

Route guidance after vehicle transpor- tation COMAND has to redetermine the position of the vehicle if the vehicle has been trans- ported (e.g. by ferry, by train or after tow- ing). Positioning takes place automatically even when COMAND is switched off. The dura- tion varies from one case to another. Route guidance may be restricted as fol- lows during vehicle positioning: 앫 Navigation announcements, route

guidance displays and displayed street names are not consistent with the ac- tual location of the vehicle.

앫 COMAND does not generate navigation

announcements.

앫 Instead of the route guidance displays, you see the “Off Road” display and a di- rection arrow. The direction arrow shows the compass heading to the des- tination.

187

Input restrictions

The input restrictions are imposed starting at a particular vehicle speed. The restric- tions are canceled as soon as the speed drops below a certain value. When the restriction is active, certain oper- ations or entries are not possible. You will notice this by the fact that some menu items cannot be selected or certain operations will not be possible.

Control systems COMAND navigation (introduction)

When positioning is complete, route guid- ance is once again possible using naviga- tion announcements and route guidance displays.

Interrupting the journey during route guidance The following applies if you interrupt the journey during route guidance and contin- ue the journey later: 앫 COMAND resumes route guidance au- tomatically if you continue the journey within 2 hours.

앫 Route guidance is canceled if you con-

tinue the journey after more than 2 hours. It will be necessary to resume the canceled route guidance manually (컄 page 240).

i The journey is interrupted if you park the ve- hicle and switch off COMAND. The journey is continued when you switch COMAND back on and start driving on.

Hard disk errors COMAND has an integrated hard disk on which the map software is saved. If an area of the hard disk has an error, COMAND can no longer access the map data in this area, for example, when calcu- lating a route. The message “Navigation Unavailable. Please refer to the operating instructions.” appears. 왘 Deleting message: Switch COMAND

off and back on.

i If you switch the navigation system off/on, it will be operational again until it has to access the faulty area of the hard disk again. The mes- sage will then appear again. Consult an autho- rized Mercedes-Benz Center.

Units of measurement The units of measurement in navigation mode are identical to those set in the in- strument cluster.

188

Navigation system menu overview

i The components and operating principles of COMAND can be found on (컄 page 83).

Info (only with route guidance active) Information about the active route guid- ance

Traffic (TMC)

Call up real-time traf- fic messages

Control systems COMAND navigation (introduction)

Route (only with route guidance active) 앫 Call up route info 앫 Call up route

browser

앫 Call up the de-

tour function

Position

앫 Call up the save position memory function

앫 Center the map on the vehicle’s position

앫 Center the map on the destina- tion position

RPT (only with route guidance active) Repeat the current navigation an- nouncement

Destination

Select: 앫 a destination 앫 stopover 앫 save destination 앫 cancel route

guidance

189

Control systems COMAND navigation (introduction)

Calling up the map display and switching to navigation mode

왘 Press the N shortcut button once or

twice.

i The number of times you have to press the N shortcut button depends on the operating mode currently selected.

or 왘 In the main function line, select “Navi”. Both of these will call up the map display. You will see the map with the menu system either shown or hidden.

190

Illustration: map with route guidance inac- tive and with the menu system shown 1 Current vehicle position

Illustration: map with route guidance inac- tive and with the menu system hidden (full screen mode) 1 Current vehicle position 2 Set map orientation (컄 page 193) 3 Map scale selected (컄 page 191)

Control systems COMAND navigation (introduction)

Adjusting the map scale

i It is only possible to adjust the map scale with the menu system hidden (full-screen map display). 왘 Rotate ymz until the desired map

scale is set.

Hiding or showing the menu system 왘 Hiding: Slide qm.

The “Full Screen” menu item appears in the main area of the display; it is auto- matically selected.

왘 Press n.

The menu system is hidden. The map can be seen in the full screen.

왘 Showing: Press n in the full-screen

map display.

1 Currently set map scale as number 2 Scale 3 Currently set map scale as a needle on

the scale

4 Previously set value before calling up

the scale As soon as you rotate ymz, scale 2 appears. Rotating clockwise zooms in, rotating counterclockwise zooms out.

Saving current vehicle position as des- tination in last destinations list 왘 Showing menu system, if neces-

sary: Press n.

왘 Saving: Select “Position” 씮 “Save Po-

sition”. COMAND saves the current vehicle po- sition as a destination in the last desti- nations (컄 page 254).

Moving the map

i It is only possible to move the map with the menu system hidden. 왘 Slide qmr, omp or wmx.

A crosshair appears on the map.

191

Control systems COMAND navigation (introduction)

1 Crosshair 2 Details of the crosshair position 3 Map scale

i Display 2 may be the name of a road, for example, provided the digital map contains the necessary data. If no data is available, display 2 shows: 앫 the coordinates of the crosshair if the geo-coordinate display is switched on (컄 page 195) and the GPS signal is strong enough

앫 no display if the geo-coordinate display is

switched off (컄 page 195)

192

Adjusting the map scale 왘 Rotate ymz.

Rotating clockwise zooms in, rotating counterclockwise zooms out.

Saving crosshair position as destination in last destinations list 왘 Showing menu system, if neces-

sary: Press n.

왘 Saving: Select “Position” 씮 “Save Po-

sition”. COMAND saves the crosshair position as a destination in the last destinations list (컄 page 254).

Hiding the crosshair 왘 Press back button L in the center

console (컄 page 84). The crosshair disappears and the map is centered on the vehicle position.

or

왘 Set the map to the vehicle or destina- tion position, see the explanation be- low.

Centering the map on the vehicle or destination position

i If you have moved the map, you can use this function to rapidly return the map to the position of the vehicle or destination. It is only possible to center the map on the destination position when route guidance is active. 왘 Centering on the vehicle’s position: Select “Navi” 씮 “Position” 씮 “Vehicle Position Map”.

or 왘 Press back button L when the

crosshair is displayed.

왘 Centering on the destination:

Select “Navi” 씮 “Position” 씮 “Destina- tion Position Map”.

Control systems COMAND navigation (introduction)

왘 Setting map orientation:

Select “Navi” 씮 “Navi” 씮 “Map Dis- play”. The map display list appears. A dot R indicates the current setting.

왘 Select “North Up” or “Heading Up”. 왘 Exiting menu: Slide omp.

The map orientation changes accord- ingly.

Basic settings

Map orientation

i You can make the following settings regard- less of whether route guidance is active or inac- tive.

Map perspective COMAND can display the map from a bird's eye view or in the normal map view. 왘 Select map perspective:

Select “Navi” 씮 “Navi” 씮 “Map Dis-