2002 Mercedes-benz CL Class Owners Manual

data

Index

J_OM_215.book Seite 134 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

134

Navigation system

1 The navigation system is switched off. 2 The navigation system is switched on but no

destination has been specified.

3 The navigation system is switched on and

destination guidance is active.

Press the è or ÿ button repeatedly until the required system is displayed. See the separate COMAND (Cockpit Management and Data System) instruction manual for notes on the navigation system. Pressing the è or ÿ button displays the next or previous system.

P54.30-2985-27

J_OM_215.book Seite 135 Mittwoch, 30. Mai 2001 2:01 14

Distronic (DTR)

1 Distronic (DTR) is deactivated. The actual

distance (4) and the should-be distance (5) to the vehicle in front (3) are displayed.

2 Distronic (DTR) is activated. The display shows the

selected speed for approximately 5 seconds.

3 Distronic (DTR) is activated. The message

“DTR OFF” appears for five seconds when Distronic is being deactivated.

4 Vehicle ahead.

Only appears if a vehicle is detected ahead.

5 Actual distance to vehicle ahead. 6 Should-be distance to vehicle ahead. 7 Own vehicle. 8 Distance warning function is activated, see

page 270.

Press the è or ÿ button repeatedly until the required system is displayed. Distronic (DTR), see page 259. Pressing the è or ÿ button displays the next or previous system.

Multifunction steering wheel, multifunction display

135

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 136 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

136

Trip computer

1 “AFTER START” — short distance memory 2 “AFTER RESET” — long distance memory 3 “RANGE” — estimated range remaining 4 Distance covered “AFTER START” or

“AFTER RESET”

5 Elapsed time “AFTER START” or “AFTER RESET” 6 Average speed “AFTER START” or “AFTER RESET” 7 Average fuel consumption “AFTER START” or

“AFTER RESET”

Press the button è or ÿ repeatedly until the display (1, 2 or 3) appears. Press the j or k button until the “AFTER START” short distance memory (1), the “AFTER RESET” long distance memory (2) or the “RANGE” – estimated range remaining indicator (3) appears. Pressing the è or ÿ button displays the next or previous system.

Note: The most recently selected display (1, 2 or 3) always appears the next time the trip computer is called up.

J_OM_215.book Seite 137 Mittwoch, 30. Mai 2001 2:01 14

Transferring values from the previous journey to the “AFTER START” short distance memory (1): The “AFTER START” display will flash until a distance of approximately 1 mile (1.6 km) has been covered or two minutes have elapsed since the engine was restarted. During this period you can incorporate the values for the previous journey by pressing button J in the instrument cluster. If button J is not pressed, the short distance memory is reset to “0”.

To reset the short “AFTER START” (1) or long “AFTER RESET” distance memory (2): Call up the relevant display (1 or 2) using the j or k button and press the J button in the instrument cluster until the values are reset to “0”.

Multifunction steering wheel, multifunction display

137

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 138 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

138

Malfunction/warning message memory

Press the è or ÿ button repeatedly until the message memory (1 or 2) is displayed. Press the j or k button if display (2) appears. The stored messages will now be displayed in order. See page 303 for malfunction and warning messages. Display (2) will reappear after you have scanned all the malfunction and warning messages. Should any malfunction or warning messages be stored while driving, they will reappear in the display (2) when the electronic key in starter switch is turned to position 0 or removed from the starter switch. The malfunction or warning messages will now be displayed for approximately 5 seconds each. Pressing the J button in the instrument cluster displays the next malfunction and warning message immediately.

1 There are no messages stored in the system. 2 Number of messages stored in the system.

J_OM_215.book Seite 139 Mittwoch, 30. Mai 2001 2:01 14

The message memory will be cleared when the electronic key is turned in the starter switch to position 1 or 2. Should any subsequent faults occur, they will be displayed in the message memory. Pressing the è or ÿ button displays the next or previous system.

Important! Malfunction and warning messages are only indicated for certain systems and displayed to a low level of detail. The malfunction and warning messages are simply a reminder with respect to the operation of certain systems and do not replace the driver’s responsibility to maintain the vehicle’s operating safety by having all required maintenance and safety checks performed on the vehicle and by bringing the vehicle to an authorized Mercedes-Benz Center to address the malfunction and warning messages. See page 303.

Multifunction steering wheel, multifunction display

139

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 140 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

140

Individual settings

1 Preliminary display of the individual settings. 2 “SETTINGS” – the requested menu can be called up

in this options menu: “INST. CLUSTER”, see page 142. “LIGHTING”, see page 144. “VEHICLE”, see page 147. These three menus contain additional submenus. Individual settings can be selected in these submenus.

3 Selection marker

Pressing button æ or ç on the multifunction steering wheel controls the selection marker.

4 See below for instructions on returning the setting

menus to the factory settings.

5 Acknowledgment

J_OM_215.book Seite 141 Mittwoch, 30. Mai 2001 2:01 14

Press the è or ÿ button repeatedly until the individual setting preliminary display (1) appears. Press the j or k button until the setting menu “SETTINGS” (2) is displayed. Pressing the æ or ç button controls the selection marker (3) in setting menu (2). “INST. CLUSTER”, see page 142. “LIGHTING”, see page 144. “VEHICLE”, see page 147. Pressing the è or ÿ button displays the next or previous system.

Notes: These settings may only be performed with the electronic key in starter switch position 1 or 2.

display (1).

To return menu “SETTINGS” (2) to its factory setting: • Call up the individual setting preliminary • Press the J button in the instrument cluster for approximately 3 seconds. Display (4) will appear. • Press the J Button once more. The menu

“SETTINGS” is reset to factory settings, acknowledged by display (5). The individual setting preliminary display (1) will appear if you do not press the J button within about 5 seconds. The setting menus will not be reset.

Note: For safety reasons, the individual setting “LAMP CIRCUIT HEADLAMP” in menu cannot be reset while driving, see page 144. If an attempt is made, the message “LIGHTING” – “CANNOT BE COMPLETELY RESET TO FACTORY SETTINGS WHILE DRIVING” will be displayed.

Multifunction steering wheel, multifunction display

141

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 142 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

142

“INST. CLUSTER” (Instrument Cluster)

J_OM_215.book Seite 143 Mittwoch, 30. Mai 2001 2:01 14

1 Preliminary display of the individual settings 2 “SETTINGS” – the menu “INST. CLUSTER” can be

called up in this option menu.

3 Selection marker

Pressing button æ or ç on the multifunction steering wheel controls the selection marker.

4 “TEMP. INDICATOR” – the unit set is displayed in the outside temperature display in the instrument cluster and in the automatic air conditioner display. 5 “SPEEDOMETER” – the unit set is displayed in the

multifunction display

6 “TEXT” – sets the language used in the

multifunction display

7 Returning the setting menu “INST. CLUSTER” to the

factory setting.

8 Acknowledgment For setting clock, see separate COMAND operator’s manual. Press the è or ÿ button repeatedly until the individual setting preliminary display (1) appears. Press the j or k button until the setting menu “SETTINGS” (2) is displayed.

Press button æ or ç until the menu “INST. CLUSTER” is selected by the selection marker (3). Press the j or k button until the required display (4 to 6) is displayed. Pressing the æ or ç button controls the selection marker. The settings made are stored and applied immediately. The individual setting preliminary display (1) will appear again after you have run through all the setting menus. Pressing the è or ÿ button displays the next or previous system.

To return menu “INST. CLUSTER” (4 to 6) to its factory setting: • Call up menu (4 to 6). • Press the J button in the instrument cluster for approximately 3 seconds. Display (7) will appear. • Press the J button once more. The menu “INST. CLUSTER” is reset to factory settings, acknowledged by display (8). The individual setting display “SETTINGS” (2) will appear if you do not press the J button within about 5 seconds. The setting menus will not be reset.

Multifunction steering wheel, multifunction display

143

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 144 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

144

“LIGHTING”

J_OM_215.book Seite 145 Mittwoch, 30. Mai 2001 2:01 14

1 Preliminary display of the individual settings 2 “SETTINGS” – the menu “LIGHTING” can be called

up in this option menu.

3 Selection marker

Pressing button æ or ç on the multifunction steering wheel controls the selection marker.

4 “LAMP CIRCUIT HEADLAMP”1, 2, see page 160. 5 “LOCATOR LIGHTING”, see page 163. 6 “HEADLAMPS DELAYED SHUT-OFF”, see “Night

security illumination” on page 162.

7 “INTERIOR LAMP DELAYED SHUT-OFF”, see

“Interior lighting” on page 189.

8 Returning the setting menu “LIGHTING” to the

factory setting.

9 Acknowledgment

1 Except Canada

2 For safety reasons, setting only possible while vehicle is standing

still.

Press the è or ÿ button repeatedly until the individual setting preliminary display (1) appears. Press the j or k button until the setting menu “SETTINGS” (2) is displayed. Press button æ or ç until the menu “LIGHTING” is selected by the selection marker (3). Press the j or k button until the required display (4 to 7) is displayed. Pressing the æ or ç button controls the selection marker. The settings made are stored and applied immediately. The individual setting preliminary display (1) will appear again after you have run through all the setting menus. Pressing the è or ÿ button displays the next or previous system.

Multifunction steering wheel, multifunction display

145

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 146 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

146

To return menu “LIGHTING” (4 to 7) to its factory setting: • Call up menu (4 to 7). • Press the J button in the instrument cluster for approximately 3 seconds. Display (8) will appear. • Press the J button once more. The menu

“LIGHTING” is reset to factory settings, acknowledged by display (9). The individual setting display “SETTINGS” (2) will appear if you do not press the J button within about 5 seconds. The setting menus will not be reset.

Note: For safety reasons, the individual setting “LAMP CIRCUIT HEADLAMP” in menu cannot be reset while driving. If an attempt is made, the message “LIGHTING” – “CANNOT BE COMPLETELY RESET TO FACTORY SETTINGS WHILE DRIVING” will be displayed.

J_OM_215.book Seite 147 Mittwoch, 30. Mai 2001 2:01 14

“VEHICLE” (audio and central locking system)

Multifunction steering wheel, multifunction display

147

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 148 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Multifunction steering wheel, multifunction display

148

1 Preliminary display of the individual settings 2 “SETTINGS” – the menu “VEHICLE” can be called

up in this option menu.

3 Selection marker

Pressing button æ or ç on the multifunction steering wheel controls the selection marker.

4 “STATION SEARCH USING”

– radio adjustment “FREQUENCY”: use the j or k button to select a frequency. – radio adjustment “MEMORY”: use the j or k button to select a stored station (preset memory).

5 “AUTOMATIC DOOR LOCK”, see automatic central

locking on page 51.

6 Returning the setting menu “VEHICLE” to the

factory setting.

7 Acknowledgment

Press the è or ÿ button repeatedly until the individual setting preliminary display (1) appears. Press the j or k button until the setting menu “SETTINGS” (2) is displayed.

Press button æ or ç until the menu “VEHICLE” is selected by the selection marker (3). Press the j or k button until the required display (4 or 5) is displayed. Pressing the æ or ç button controls the selection marker. The settings made are stored and applied immediately. The individual setting preliminary display (1) will appear again after you have run through all the setting menus. Pressing the è or ÿ button displays the next or previous system.

To return menu “VEHICLE” (4 and 5) to its factory setting: • Call up menu (4 or 5). • Press the J button in the instrument cluster for approximately 3 seconds. Display (6) will appear. • Press the J button once more. The menu

“VEHICLE” is reset to factory settings, acknowledged by display (7). The individual setting display “SETTINGS” (2) will appear if you do not press the J button within about 5 seconds. The setting menus will not be reset.

J_OM_215.book Seite 149 Mittwoch, 30. Mai 2001 2:01 14

Setting the audio volume You can only adjust the volume of the system currently in use. The volume setting for each system (audio, telephone, navigation and voice recognition system) is stored separately.

Setting button: æ increases the volume. ç reduces the volume.

Multifunction steering wheel, multifunction display

149

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 150 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Flexible service system

150

Flexible service system (FSS) (service indicator)

P54.30-2768-26

The FSS permits a flexible service schedule that is directly related to the operating conditions of the vehicle. The symbol 9 or ½ appears together with a message in the multifunction indicator prior to the next suggested service. Depending on operating conditions throughout the year, the next service is calculated and displayed in days or distance remaining.

The message is displayed for approximately 10 seconds when turning the electronic key in starter switch to position 2, or while driving when reaching the service warning threshold. The symbols and messages indicate the type of service to be performed: 9 Service A ½ Service B One of the following messages will appear in the display (e.g. Service A): “SERVICE A – IN xx DAYS” “SERVICE A – IN xx MILES” (Canada: KM) “SERVICE A – EXCEEDED BY xx DAYS” “SERVICE A – EXCEEDED BY xx MILES” (Canada: KM) “SERVICE A – PERFORM SERVICE”

The next service due date is displayed either in days or in miles, depending on your driving style. Once the suggested service term has passed, the symbol and message appear for approximately 30 seconds and a signal sounds every time when turning the electronic key in starter switch to position 2.

J_OM_215.book Seite 151 Mittwoch, 30. Mai 2001 2:01 14

The service indicator disappears automatically after 30 seconds or if button J on the instrument cluster is pressed. Calling up service indicator manually: Turn the electronic key in starter switch to position 1 or 2. Call up the trip odometer and main odometer by pressing button è or ÿ on the multifunction steering wheel until the display appears. See page 124. Press button j or k until the FSS indicator appears. The next or previous system is displayed by pressing button è or ÿ.

Important! The FSS indicator is not an engine oil level indicator. See page 157 for engine oil level indicator.

Note: When disconnecting vehicle battery for one or more days at a time, such days will not be counted. Any such days not counted by the FSS can be added by your Mercedes-Benz Center. The interval between services is determined by the type of driving for which the vehicle is used. For example, driving at extreme speeds, and cold starts combined with short distance driving in which the engine does not reach operating normal temperature, reduce the interval between services.

Flexible service system

151

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 152 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Flexible service system

152

Following a completed A or B service the Mercedes-Benz Center sets the counter mileage to 10 000 miles (Canada: 15 000 km). The counter can also be set by any individual. To do so: Turn the electronic key in starter switch to position 2. To call up the trip odometer and main odometer, press button è or ÿ on the multifunction steering wheel until the display appears. See page 124. Press button j or k until the FSS indicator appears. Press button J on the instrument cluster for approximately 2 seconds.

The multifunction display will show the question: “DO YOU WANT TO RESET SERVICE INTERVAL? – CONFIRM BY PRESSING RESET (R) BUTTON” Press button J on the instrument cluster again to reset the service indicator. The new service indicator is displayed with the reset distance of 10 000 miles (Canada 15 000 km). If the FSS counter was inadvertently reset, have a Mercedes-Benz Center correct it. However you choose to set your reference numbers, the scheduled services as posted in the Service Booklet must be followed to properly care for your vehicle.

J_OM_215.book Seite 153 Mittwoch, 30. Mai 2001 2:01 14

Tire inflation pressure monitor (optional for Canada) The tire inflation pressure, as selected by the driver, is monitored in all four wheels on the ground. A warning is issued to the driver in the case of a decrease in the inflation pressure in one or more of the tires.

Warning! The tire inflation pressure monitor does not indicate a warning for wrongly selected inflation pressures. Always adjust tire inflation pressure according to the label affixed on the fuel filler flap. See page 351 for tire inflation pressure. The tire inflation pressure monitor is not able to issue a warning due to a sudden loss of pressure (e.g. tire puncture caused by a foreign object). In this case bring vehicle to a halt by carefully applying the service brakes and avoiding abrupt steering maneuvers.

Inquiry of present tire inflation pressure

Turn electronic key in starter switch to position 1 or 2. Press è or ÿ button on the multifunction steering wheel until the display for trip and main odometer appears, see page 124. Press the j or k button repeatedly until the tire inflation pressure monitor is displayed. The present tire inflation pressure for each wheel is displayed in multifunction display.

Tire inflation pressure monitor

153

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 154 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Tire inflation pressure monitor

154

Notes: Following a tire inflation pressure reactivation process the real tire inflation pressures are displayed only after a few minutes travel time. Possible differences between readings of a tire pressure gauge of an air hose, e.g. gas station equipment, and the vehicle’s multifunction display can occur. The vehicle’s multifunction display of the tire inflation pressure monitor is a more precise reading.

Activation of tire inflation pressure monitor Activation of tire inflation pressure monitor is necessary if tire inflation pressure is being changed, wheels or tires are replaced, or new wheels are installed on the vehicle. Tire inflation pressure should be checked and corrected according to the label affixed inside the fuel filler flap. For a detailed description, refer to page 351. Turn electronic key in starter switch to position 2 (the engine must not be running).

J_OM_215.book Seite 155 Mittwoch, 30. Mai 2001 2:01 14

Press button æ (“YES”) on the multifunction steering wheel to activate the tire inflation pressure monitor. The message “TIRE PRESS. MONITOR – ACTIVATED!” – “PRESS. DISPLAY AFTER DRIVING A FEW MINS.” appears in the multifunction display. The tire inflation pressure monitor is now activated and monitors the presently selected tire pressure for all four wheels on the ground. Press button ç (“NO”) on the multifunction steering wheel to cancel the activation. Repeat above steps if the multifunction display shows the message “REACTIVATE – TIRE PRESS. MONITOR!”. A multifunction display showing the message “TIRE PRESSURE – CHECK TIRES!” indicates a much too low tire inflation pressure. Check and correct tire inflation pressure again on all wheels, and repeat the tire inflation pressure monitor activation steps listed above.

Press è or ÿ button on the multifunction steering wheel until the display for trip and main odometer appears, see page 124. Press the j or k button repeatedly until the tire inflation pressure monitor appears. Press and hold button J on the instrument cluster until the message “CHECK CURRENT TIRE PRESSURE?” appears. Release button J.

Tire inflation pressure monitor

155

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 156 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Tire inflation pressure monitor

156

To prevent possible damage to the electronic sensors, have tire changes only performed at an authorized Mercedes-Benz Center. For malfunction and warning messages, see page 318. When checking the tire inflation pressure of the road wheels, also check the spare tire. The tire inflation pressure of the spare wheel, mounted or not mounted, is not monitored by the tire inflation pressure monitor. See page 341 for location of the spare wheel, and page 351 for tire inflation pressure.

Notes: To ensure proper functioning of the tire inflation pressure monitor, the tire inflation pressure should be checked and corrected according to the label affixed inside the fuel filler flap. For a detailed description, refer to page 351. The message “REACTIVATE – TIRE PRESS. MONITOR” appears if the tire inflation pressure shows an increase of 4.4 psi (0.3 bar) or more. Reactivate the tire inflation pressure monitor. The tire inflation pressure monitor only functions on wheels equipped with the proper electronic sensors. Inquire at your authorized Mercedes-Benz Center about retrofitting other than original Mercedes-Benz wheels with electronic sensors. Transporting a deflated road wheel in the vehicle, e.g. after having a flat, the tire inflation pressure monitor should only be activated once the flat tire and rim are removed from the vehicle.

J_OM_215.book Seite 157 Mittwoch, 30. Mai 2001 2:01 14

Engine oil level indicator

To check the engine oil level, park vehicle on level ground, with engine at normal operational temperature. Check oil level approximately 5 minutes after stopping the engine, allowing for the oil to return to the oil pan. The message “OBSERVE WAITING PERIOD” (perform service [engine oil level check] on time) will be displayed if the required waiting period has not been observed after stopping the engine: • with engine at operational temperature

approximately 5 minutes.

Engine oil level indicator

157

• with engine not at operational temperature up to

approximately 30 minutes.

The engine oil level check can be repeated after a short time. Turn the electronic key in starter switch to position 2. To call up the trip odometer and main odometer, press button è or ÿ on the multifunction steering wheel until the display appears. See page 124. Press button j or k on the multifunction steering wheel repeatedly until the “CORRECT MEASUREMENT ONLY – IF VEHICLE LEVEL” engine oil level indicator appears. This indicator is only a reminder. Measurement can be cancelled by pressing button j or k if the vehicle is not parked on level ground. An incorrect reading will be recorded if you do not cancel the measurement. Move the vehicle to level ground and measure again. The electronic key in starter switch is not in position 2 if the “ENGINE OIL LEVEL – IGNITION ON PLEASE” message appears. The “ENGINE OIL LEVEL – MEASUREMENT IN PROCESS” message is displayed after approximately 3 seconds.

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 158 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Engine oil level indicator

158

One of the following messages will subsequently appear on the indicator: “ENGINE OIL LEVEL – O.K.” No oil needs to be added. “ENGINE OIL LEVEL – ADD 1.0 QUART” (Canada: 1.0 L) “ENGINE OIL LEVEL – ADD 1.5 QUART” (Canada: 1.5 L) “ENGINE OIL LEVEL – ADD 2.0 QUART” (Canada: 2.0 L) See “Checking engine oil level”, on page 337 for instructions on adding engine oil. “ENGINE OIL LEVEL – REDUCE OIL LEVEL” Do not overfill the engine. Excessive oil must be siphoned or drained off. It could cause damage to the engine and catalytic converter not covered by the Mercedes-Benz Limited Warranty. The “MEASURING NOT POSSIBLE!” message will be displayed if a proper oil level check cannot be performed. The engine oil level check can be repeated after a short while.

CL 500 and CL 55 AMG only: Perform the engine oil level check with the dipstick, if it cannot be completed via the multifunction display. See “Checking engine oil level”, page 337. In this case we recommend that you have the system checked at a Mercedes-Benz Center.

Notes: See malfunction and warning messages on page 303 and page 320 if an engine oil level indicator appears on the multifunction display when the engine is running. The engine oil level cannot be checked while the engine is running. The “ENGINE OIL LEVEL – NOT WHEN ENGINE ON” message will appear.

Engine oil consumption Engine oil consumption checks should only be made after the break-in period. During the break-in period, higher oil consumption may be noticed and is normal. Frequent driving at high engine speeds results in increased consumption.

J_OM_215.book Seite 159 Mittwoch, 30. Mai 2001 2:01 14

Exterior lamp switch

P54.25-2390-26

M Off U Automatic headlamp mode, see below. C Parking lamps (also side marker lamps, taillamps,

licence plate lamps, instrument panel lamps) Canada only: When the engine is running, the low beam is additionally switched on.

B Parking lamps plus low beam or high beam

headlamps (combination switch pushed forward).

ˆ Standing lamps, right (turn left one stop) ‚ Standing lamps, left (turn left two stops) ‡ Front fog lamps (pull out one stop) with parking

lamps and/or low beam headlamps on. Green indicator in lamp switch comes on.

† Rear fog lamp (pull out to second detent) in

addition to the front fog lamps. Yellow indicator in lamp switch comes on.

Note: With the electronic key removed and the driver’s door open, a warning sounds if the vehicle’s exterior lamps (except standing lamps) are not switched off. Fog lamps will operate with the parking lamps and/or the low beam headlamps on. Fog lamps should only be used in conjunction with low beam headlamps. Consult your State or Province Motor Vehicle Regulations regarding allowable lamp operation. Fog lamps are automatically switched off when the exterior lamp switch is turned to position M or U.

Exterior lamp switch

159

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 160 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Exterior lamp switch

160

Headlamp mode Manual headlamp mode The low beam headlamps and parking lamps can be switched on and off with the exterior lamp switch. For exterior lamp switch, see above.

Note: With the daytime running lamp mode activated and the engine running, the low beam headlamps can not be switched off manually.

Warning! The driver is responsible for the operation of the vehicle’s lights at all times. The automatic headlamp feature is only an aid to the driver. Switch on the vehicle lights by hand when driving or traffic conditions require you to do so.

Automatic headlamp mode Turn exterior lamp switch to position U. • Electronic key in starter switch position 1:

The parking lamps switch on and off automatically depending on the brightness of the ambient light. • Electronic key in starter switch position 2 and the

engine running: The low beam headlamps and parking lamps are switched on and off automatically depending on the brightness of the ambient light. The low beam headlamps and parking lamps can still be switched on and off manually using the exterior lamp switch.

Note: With the daytime running lamp mode activated, the low beam headlamps can not be switched off manually. The headlamps will not be automatically switched on under foggy conditions. Front fog lamps and rear fog lamp can not be switched on manually with exterior lamp switch in position U. To activate the fog lamps turn exterior switch to position B.

J_OM_215.book Seite 161 Mittwoch, 30. Mai 2001 2:01 14

Daytime running lamp mode Turn exterior lamp switch to position M or U. When the engine is running, the low beam headlamps are automatically switched on. In low ambient light conditions the parking lamps will also switch on. • Canada only:

When shifting from a driving position to position “N” or “P”, the low beam switches off (3 minutes delay). For nighttime driving the exterior lamp switch should be turned to position B to permit activation of the high beam headlamps.

• USA only:

The high beam headlamps can also be activated when driving with the daytime running lamp mode activated and exterior lamp switch in position M. To activate the daytime running lamp mode, see the individual setting menu “LIGHTING” – “LAMP CIRCUIT HEADLAMP” on page 144.

Note: See page 159 for notes on the exterior lamp switch.

Exterior lamp switch

161

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 162 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Exterior lamp switch

162

Night security illumination Turn exterior lamp switch to position U. At low ambient light conditions and with the engine having been turned off, the exterior lamps (fog lamps and parking lamps) switch on for added illumination. After the last door has been closed the lamp-on time period commences. To activate the function see the individual setting menu “LIGHTING” –“HEADLAMPS DELAYED SHUT-OFF” on page 144. The lamp-on time period for night security illumination can be set at several different timed levels from 0 (off) to 60 seconds.

Note: Within 10 minutes after closing the last door the night security illumination can be reactivated by opening a door. If after switching the engine off, no doors are opened or if after opening the doors they are not closed, the night security illumination will switch off after approximately 60 seconds.

Deactivating night security illumination temporarily: Turn the electronic key in starter switch to position 0 then to position 2 and back to position 0 again before getting out of the vehicle. The night security illumination will not be activated when the door is opened.

J_OM_215.book Seite 163 Mittwoch, 30. Mai 2001 2:01 14

Locator lighting Turn exterior lamp switch to position U. After unlocking the vehicle with the electronic key during darkness the fog lamps and parking lamps switch on for a approximately 40 seconds. The exterior lamps will be switched off when opening the driver’s door. To activate the function see the individual setting menu “LIGHTING” –“LOCATOR LIGHTING” on page 144.

Headlamp cleaning system

P54.25-2391-26

Turn the electronic key in starter switch to position 1 or 2. The headlamps will be cleaned with a high-pressure water jet when you press the headlamp washer button (1). See page 340 for instructions on filling up the windshield/headlamp washer reservoir.

Exterior lamp switch

163

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 164 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Combination switch

164

Combination switch

P54.25-2388-26

1 Low beam

(exterior lamp switch position B)

2 High beam

(exterior lamp switch position B)

3 High beam flasher (high beam available

independent of exterior lamp switch position)

4 Turn signals, right 5 Turn signals, left

To signal minor directional changes, such as changing lanes on a highway, move combination switch briefly to the point of resistance only and release. The turn signals blink three times. To operate the turn signals continuously, move the combination switch past the point of resistance (up or down). The switch is automatically canceled when the steering wheel is turned to a large enough degree.

Turn signal failure If one of the turn signals fails, the turn signal indicator system flashes and sounds at a faster than normal rate.

J_OM_215.book Seite 165 Mittwoch, 30. Mai 2001 2:01 14

P54.25-2389-26

6 Press switch briefly:

Single wipe without washer fluid (select only if windshield is wet). Push switch past resistance point: Windshield washer system, windshield wipers. See page 340 for instructions on filling the windshield/headlamp washer reservoir.

7 Windshield wipers

0 Off

Intermittent wiping One initial wipe, pauses between wipes are automatically controlled by a rain sensor monitoring the wetness of the windshield. This will not occur with a front door open. Notes: With switch in this position, one wipe occurs when turning the electronic key in starter switch from position 0. However, this might cause scratches on a dry windshield. Turn combination switch to Off position before turning the electronic key in starter switch from position 0. Do not leave in intermittent setting when vehicle is taken to an automatic car wash or during windshield cleaning. Wipers will operate in presence of water spray at windshield, and wipers may be damaged as a result.

II Normal wiper speed III Fast wiper speed

If the vehicle is standing still, the wiper will switch back to setting I, intermittent wiping.

Combination switch

165

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 166 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Combination switch

166

Blocked windshield wipers If the windshield wipers become blocked (for example, due to snow), switch off the wipers. For safety reasons before removing ice or snow, remove electronic key from starter switch. Remove blockage. Activate combination switch again (electronic key in starter switch position 1).

Windshield wipers smear If the windshield wipers smear the windshield, even during rain, activate the washer system as often as necessary. The fluid in the washer reservoir should be mixed in the correct ratio. See page 340 for instructions on filling up the windshield/headlamp washer reservoir.

Emergency operation of windshield wipers In case of windshield wiper malfunction in switch positions I or III, turn combination switch to wiper setting II. Have the system checked at your authorized Mercedes-Benz Center as soon as possible.

Windshield and headlamp washer fluid mixing ratio For temperatures above freezing: MB windshield washer concentrate “S” and water. 1 part “S” to 100 parts water (40 ml “S” to 1 gallon water). For temperature below freezing: MB windshield washer concentrate “S” and commercially available premixed windshield washer solvent/antifreeze. 1 part “S” to 100 parts solvent (40 ml “S” to 1 gallon solvent).

J_OM_215.book Seite 167 Mittwoch, 30. Mai 2001 2:01 14

Hazard warning flasher switch

Note: With the hazard warning flasher activated, the combination switch in position for either left or right turn, and the electronic key in starter switch position 1 or 2, only the respective left or right side turn signals will operate.

The hazard warning flasher can be activated either manually via the switch located in the dashboard, or it is activated automatically at the time an airbag is deployed. To activate hazard warning flasher, press switch once. To deactivate, press switch again. If hazard warning flasher was activated automatically, press switch twice to deactivate.

Hazard warning flasher

167

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 168 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

168

Automatic climate control

3 4 5

11

10

12

P83.40-2298-29

J_OM_215.book Seite 169 Mittwoch, 30. Mai 2001 2:01 14

1 Center air outlet, left, adjustable 2 Fixed air outlet, left 3 Air volume control for left center air outlet

To open: Turn the thumbwheel upward. I: II: The left center and fixed air outlets are

The left center air outlet is fully open.

opened.

4 Air temperature control for center air outlets

To lower temperature: Turn thumbwheel towards the blue marking. Automatic mode: Turn thumbwheel to position A. The indicator lamp above the thumbwheel will illuminate. The airflow and temperature for the center air outlets are regulated automatically. 5 Air volume control for right center air outlet.

To open: Turn the thumbwheel upward I: II: The right center and fixed air outlets are

The right center air outlet is fully open.

opened.

6 Center air outlet, right, adjustable 7 Fixed air outlet, right 8 Side defroster outlet, left and right, fixed 9 Side air outlet, left and right, adjustable 10 Air volume control for side air outlets To open: Turn thumbwheel outwards I: II: The side and door air outlets are opened.

The side air outlet is fully opened.

11 Door air outlet, left and right 12 Display and controls

Note: We recommend that the sliders for the air outlets (1, 6, 9) be clicked to the automatic position to provide practically draft free ventilation.

Automatic climate control

169

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 170 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

170

Display and controls

13

12

11

10

P83.40-2291-26

1 Defrosting 2 Rear window defroster, see page 181
3 Residual engine heat utilization, see page 179
4 Automatic climate control on/off 5 Air distribution, right (automatic, manual operation) 6 Economy mode, see page 178
7 Temperature control, right

8 Air volume (automatic, manual) 9 Display

Depending on the ambient light conditions, the figures on the display will be shown as dark figures on a bright background (in daylight), or as bright figures on a dark background (at night).

10 Temperature control, left 11 Air recirculation, see page 176
12 Air distribution, left (automatic, manual operation) 13 Activated charcoal filter

Important! This vehicle is equipped with an air conditioning system that uses R-134a (HFC: hydrofluorocarbon) as a refrigerant. Repairs should always be performed by a qualified technician, and refrigerant should be collected in a recovery system for recycling.

J_OM_215.book Seite 171 Mittwoch, 30. Mai 2001 2:01 14

Automatic climate control The system is always at operational readiness, except when manually switched off. The automatic climate control only operates with the engine running. The temperature selector should be left at the desired temperature setting. The temperature selected is reached as quickly as possible. The system will not heat or cool any quicker by setting a higher or lower temperature. The desired interior temperature and air distribution can be selected separately for the left and right side of the passenger compartment. Make the temperature settings in small increments. The automatic climate control removes considerable moisture from the air during operation in the cooling mode. It is normal for water to drip on the ground through ducts in the underbody. The air conditioning will not engage (no cooling) if the economy mode ACOFF selected, see page 178.

Notes: The current settings (Temperature, Air volume, ACOFF, Activated charcoal filter, ON/OFF) are stored for each electronic key before the electronic key is removed from the starter switch or when the vehicle is locked using the KEYLESS-GO-card (vehicles with keyless-go), see key dependent memory settings on page 113. Do not obstruct the air flow by placing objects on the air flow-through exhaust slots below the rear window. Also keep the air intake grill in front of the windshield free of snow and debris. The storage compartment between the front seats can be ventilated. See page 180 for notes on ventilating the storage space under the armrest in the center console. The air conditioner switches itself off for its own protection if refrigerant is lost. No cooling will then take place. Economy mode ACOFF cannot be switched off. Have the air conditioner checked by a Mercedes-Benz Center should this happen. If the vehicle interior has been heated by direct sunlight and it is very hot, ventilate the interior (open door or windows for a short period) before driving off.

Automatic climate control

171

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 172 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

172

Dust filter Nearly all dust particles and pollen are filtered out before outside air enters the passenger compartment through the air distribution system.

Automatic maximum cooling (MAXCOOL)

With the automatic climate control set to automatic, the system will automatically switch to maximum cooling output when necessary to achieve the set temperature quickly, see page 173. The display shows “AUTO MAXCOOL”. The temperature setting cannot be changed during maximum cooling operation.

Note: By pressing one of the temperature buttons, the system will display briefly (approx. 5 seconds) the set temperature in the display.

J_OM_215.book Seite 173 Mittwoch, 30. Mai 2001 2:01 14

Basic setting – automatic mode

In the automatic mode the automatic climate control cools or heats the interior depending on the direction and strength of the sunlight, outside temperature, selected interior temperature and the actual interior temperature of the vehicle. With the automatic climate control switched off, the air volume and distribution can still be set manually.

There are three basic settings for the automatic mode: • Automatic air volume control • Automatic air outlet control, left and right • Automatic air outlet control, center, see page 169

We recommend these settings to be used all year round.

Air volume and distribution are controlled automatically. We recommend to set the temperature switches on the left and right to 72°F (22°C). Please make changes from this setting to suit your personal requirements.

Automatic airflow regulation: Press the A on the air volume switch. The display shows “AUTO”.

Automatic air distribution: Press on both U knobs until they click in. The h, j and k symbols will no longer be visible. The economy mode and air recirculation functions will be switched off. The automatic blower will be activated at the same time.

Automatic climate control

173

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 174 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

174

Special settings (use only for short duration)

Air volume, manual

Press the air volume switch up or down. Seven blower speeds can be selected.

P83.40-2300-21

Air distribution, manual: Press U button. The button pops out, the h, j and k symbols are visible. Turn the button to select the air distribution desired. h Air from the center, side and door air outlets. j Air from the center, side, door and windshield air

outlets.

k Air from the center, side, door and footwell air

outlets.

To return to automatic mode: Press the U button until it clicks in. The h, j and k symbols will no longer be visible.

J_OM_215.book Seite 175 Mittwoch, 30. Mai 2001 2:01 14

Defrosting

P83.40-2009-21

Press the P button. The display shows P. Maximum heated and automatically controlled amount of air is directed to the defroster and windshield air outlets. Switch off air recirculation, if selected: Press button O. The indicator lamp in the button will go out. Pressing the P button again returns the system to the previous setting.

Windows fogged on the inside Switch off the economy mode, if selected: Press button ACOFF. The indicator lamp in the button will go out. Switch off air recirculation, if selected: Press button O. The indicator lamp in the button will go out. Adjust left and right air outlets upwards. Set blower to the maximum blower speed. Increase temperature setting. Open the side air outlets and direct them onto the side windows.

Automatic climate control

175

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 176 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic climate control

176

Windshield fogged on the outside Switch on the windshield wiper. Press on both U buttons until they click in. The h, j and k symbols will no longer be visible.

Air recirculation Select air recirculation: The indicator lamp in the O button is not illuminated. Press button O briefly. The indicator lamp in the button illuminates. Switch off the air recirculation: The indicator lamp in the O button is illuminated. Press button O briefly. The indicator lamp in the button will go out.

Switching on air recirculation and activating convenience closing of power windows and sliding/ pop-up roof: The indicator lamp in the button O is not illuminated. Press and hold button O until the side windows and the sliding/pop-up roof are closed. The indicator lamp in the button lights up. Switching off air recirculation and activating convenience opening of power windows and sliding/ pop-up roof: The indicator lamp in the button O is illuminated. Press and hold button O until the side windows and the sliding/pop-up roof are in the desired position.

J_OM_215.book Seite 177 Mittwoch, 30. Mai 2001 2:01 14

The system automatically switches from air recirculation to fresh air: • after 30 minutes if the outside temperature is above

about 40°F (5°C),

• after 5 minutes if the outside temperature is below

about 40°F (5°C),

• after 5 minutes if economy mode ACOFF is selected. The system switches automatically to air recirculation at high outside temperatures. A quantity of outside air is added after a maximum of 30 minutes.

Important! If the windows should fog up from the inside, switch from recirculated air back to fresh air.

Activated charcoal filter An activated charcoal filter markedly reduces bad odors and removes pollutants from air entering the passenger compartment. Select activated charcoal filter: The indicator lamp in the e button is not illuminated. Press e button briefly. The indicator lamp in the button illuminates. Switch off activated charcoal filter: The indicator lamp in the e button is illuminated. Press e button briefly. The indicator lamp in the button goes out. The system switches automatically to the air recirculation mode, if the carbon monoxide (CO) or nitrogen oxides (NOX) concentration of the outside air increases beyond a predetermined level. The automatic air recirculation mode does not function if economy mode ACOFF is selected or if the outside temperature has fallen below 40°F (5°C).

Automatic climate control

177