2002 Mercedes-benz CL Class Owners Manual

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 222 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Tele Aid

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Notes: The indicator lamp in the Information button ¡ remains illuminated in red for approx. 10 seconds during the system self-check after turning electronic key in starter switch to position 2 (together with the “SOS” button and the Roadside Assistance button (cid:127)). See system self-check on page 216 when the indicator lamp does not light up in red or stays on longer than approximately 10 seconds. If the indicator lamp in the Information button ¡ is illuminated continuously and there was no voice connection to the Response Center established, then the Tele Aid system could not initiate an Information call (e.g. the relevant cellular phone network is not available). The message “info – CALL FAILED” appears in the multifunction display. Information calls can be terminated using the ì button on the multifunction steering wheel.

222

Important! If the indicator lamps do not start flashing after pressing one of the buttons or remain illuminated (in red) at any time, the Tele Aid system has detected a fault or the service is not currently active, and may not initiate a call. Visit your Mercedes-Benz Center and have the system checked or contact the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada) as soon as possible.

Upgrade Signals Tele Aid system processes calls using the following priority. • Automatic emergency – First priority • Manual emergency – Second priority • Roadside assistance – Third priority • Information – Fourth priority Should a higher priority call be initiated while you are connected, an upgrade (alternating) tone will be heard, and the appropriate indicator lamp will flash. If certain information such as vehicle identification number or customer information is not available, the operator may need to retransmit.

J_OM_215.book Seite 223 Mittwoch, 30. Mai 2001 2:01 14

During this time you will hear a chirp and voice contact will be interrupted. Voice contact will resume once the retransmission is completed. Once a call is concluded, a chirp will be heard and the appropriate indicator lamp will stop flashing. The COMAND system operation will resume.

Important! If the indicator lamp continues to flash or the system does not reset, contact the Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada), or Mercedes-Benz Customer Assistance at 1-800-FOR-MERCedes (1-800-367-6372) in the USA or Customer Service at 1-800-387-0100 in Canada.

Notes: The indicator lamp in the respective button flashes until the call is concluded. Calls can only be terminated by a Response Center or Customer Assistance Center representative except Roadside Assistance and Information calls, which can also be terminated by pressing ì button on the multifunction steering wheel. When a Tele Aid call has been initiated, the COMAND system audio is muted and the selected mode (radio, tape or CD) pauses. The optional cellular phone (if installed) switches off. If you must use this phone, the vehicle must be parked. Disconnect the coiled cord and place the call. The navigation system (if engaged) will continue to run. The display in the instrument cluster is available for use and spoken commands are only available by pressing the RPT button on the COMAND unit. A pop-up window will appear in the COMAND display to indicate that a Tele Aid call is in progress.

Tele Aid

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

223

J_OM_215.book Seite 224 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Tele Aid

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Remote door unlock In the case you have your vehicle locked unintentionally (e.g. key inside vehicle), and no other key is available, contact the Mercedes-Benz Response Center at 1-800-756-9018 (in the USA) or 1-888-923-8367 (in Canada). You will be asked to provide your password which you provided when you completed the subscriber agreement. Then return to your vehicle and press trunk lock for minimum of 20 seconds until the “SOS” button is flashing. The message “EMERGENCY CALL – CALL CONNECTED” appears in the multifunction display. As an alternative, you may unlock the vehicle via Internet using the ID and password sent to you shortly after the completion of your Acquaintance Call. The Response Center will then unlock your vehicle with the remote door unlocking feature.

224

Notes: The remote door unlock feature is available if the relevant cellular phone network is available. The “SOS” button will flash and the message “EMERGENCY CALL – CALL CONNECTED” will appear in the multifunction display to indicate receipt of the door unlock command. Once the vehicle is unlocked, a Response Center specialist will attempt to establish voice contact with the vehicle occupants. If the trunk button was pressed for more than 20 seconds before door unlock authorization was received by the Response Center, you must wait 15 minutes before pressing the trunk button again.

J_OM_215.book Seite 225 Mittwoch, 30. Mai 2001 2:01 14

Stolen vehicle tracking services In the event your vehicle was stolen, report the incident to the police who will issue a numbered incident report. Pass this number on to the Mercedes-Benz Response Center. The Response Center will then attempt to covertly contact the vehicle’s Tele Aid system. Once the vehicle is located, the Response Center will contact the local Law Enforcement and you. The vehicle’s location will only be provided to Law Enforcement.

Info Services (optional, except Canada) Info Services categories include news, sports, stocks, weather and calendar reminders. Choices can be selected via www.mbusa.com or by calling 1-800-FOR- MERcedes. To request Info Services, press the SVC button on the COMAND system, then select “SEND NEW REQUEST FOR INFO SERVICE”. “NEW INFO SERVICE REQUEST TRANSMITTED” will appear in the COMAND display and call status messages will appear in the multifunction display.

Once information is available, the message “NEW INFO RECEIVED – READ LATER WHEN STOPPED?” will appear. Select “Yes”. With the vehicle stopped in a safe location press SVC, then select “View Info Service of mm.dd.yyyy hh.mm”. Messages will be retained for 30 minutes once the ignition is switched off.

Important! Tele Aid utilizes the cellular network for communication and the GPS (Global Positioning System) satellites for vehicle location. If either of these signals are unavailable, the Tele Aid system may not function and if this occurs, assistance must be summoned by other means.

Warning! If the indicator lamp in the “SOS” button does not illuminate during or remains illuminated after the system self-check or if the message “TELE AID – VISIT WORKSHOP” appears in the multifunction display, have the system checked at the nearest Mercedes-Benz Center as soon as possible.

Tele Aid

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

225

J_OM_215.book Seite 226 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Catalytic converter

226

Warning! As with any vehicle, do not idle, park or operate this vehicle in areas where combustible materials such as grass, hay or leaves can come into contact with the hot exhaust system, as these materials could be ignited and cause a vehicle fire.

Catalytic converter Your Mercedes-Benz is equipped with monolithic type catalytic converters, an important element in conjunction with the oxygen sensors to achieve substantial control of the pollutants in the exhaust emissions. Keep your vehicle in proper operating condition by following our recommended maintenance instructions as outlined in your Service Booklet.

Caution! To prevent damage to the catalytic converters, use only premium unleaded gasoline in this vehicle. Any noticeable irregularities in engine operation should be repaired promptly. Otherwise, excessive unburned fuel may reach the catalytic converter causing it to overheat, which could start a fire.

J_OM_215.book Seite 227 Mittwoch, 30. Mai 2001 2:01 14

Emission control Certain systems of the engine serve to keep the toxic components of the exhaust gases within permissible limits required by law. These systems, of course, will function properly only when maintained strictly according to factory specifications. Any adjustments on the engine should, therefore, be carried out only by qualified Mercedes- Benz Center authorized technicians. Engine adjustments should not be altered in any way. Moreover, the specified service jobs must be carried out regularly according to Mercedes-Benz servicing requirements. For details refer to the Service Booklet.

Warning! Inhalation of exhaust gas is hazardous to your health. All exhaust gas contains carbon monoxide, and inhaling it can cause unconsciousness and lead to death. Do not run the engine in confined areas (such as a garage) which are not properly ventilated. If you think that exhaust gas fumes are entering the vehicle while driving, have the cause determined and corrected immediately. If you must drive under these conditions, drive only with at least one window fully open.

Emission control

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

227

J_OM_215.book Seite 228 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Starter switch

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Starter switch

0 The electronic key can be withdrawn in this position

only. The electronic key can be removed only with the selector lever in position “P”. After removing the electronic key or with the electronic key in starter switch position 0 or 1 the selector lever is locked in position “P”.

228

1 Most electrical consumers can be operated. For

detailed information see respective subjects.

2 Driving position.

Gear selector lever is unlocked. To move the selector lever out of position “P” firmly depress the service brake pedal.

3 Starting position. See page 233 for instructions on starting and turning off the engine. See page 43 for instructions on the simultaneous use of the electronic key and the KEYLESS-GO-function.

Warning! When leaving the vehicle always remove the electronic key from the starter switch, take the KEYLESS-GO-card (if so equipped) with you and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause serious personal injury.

J_OM_215.book Seite 229 Mittwoch, 30. Mai 2001 2:01 14

Important! If the electronic key is left in the starter switch position 0 for an extended period of time, it can no longer be turned in the lock. In this case, remove electronic key from starter switch and reinsert.

Caution! To prevent accelerated battery discharge and a possible dead battery, always remove the electronic key from the starter switch. Do not leave the electronic key in starter switch position 0.

Notes: A warning sounds when the driver’s door is opened with the electronic key in starter switch position 1 or 0. If the electronic key cannot be turned in the starter switch, the vehicle battery may not be sufficiently charged. See battery on page 352 or jump starting on page 355. With the engine at idle speed, the charging rate of the alternator (output) is limited. It is therefore recommended that you turn off unnecessary electrical consumers while driving in stop- and-go traffic. This precaution helps to avoid draining of the battery. Unnecessary strain on the battery and charging system may be minimized by turning off the following power consumers, for example: Heated seats, rear window defroster. In addition, the automatic climate air volume control should be set to the lowest position.

Starter switch

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

229

J_OM_215.book Seite 230 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Starter switch — KEYLESS-GO

230

Start-/Stop button (vehicles with KEYLESS-GO)

Symbols on start-/stop button for Canada only:

P82.50-2058-26

See page 233 for instructions on starting and turning off the engine. See page 43 for instructions on the simultaneous use of the electronic key and the KEYLESS-GO-function.

Warning! When leaving the vehicle always take the electronic key and the KEYLESS-GO-card with you, and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause serious personal injury.

Pressing the start-/stop button (1) on the gear selector lever without depressing the brake pedal will sequentially activate the starter switch positions 1 (on) and 2 (operation) and 0 (off). The engine can be started with the starter switch in any position (on, operation or off), as long as the gear selector lever is in position “P” or “N” and the brake pedal depressed.

J_OM_215.book Seite 231 Mittwoch, 30. Mai 2001 2:01 14

“On” position (starter switch position 1, see page 228). Most electrical consumers can be operated. For detailed information see respective subjects.

Operation/driving position (starter switch position 2, see page 228). All electrical consumers can be operated. Gear selector is unlocked.

“Off” position (electronic key removable from starter switch). Most electrical consumers cannot be operated. The selector lever is locked in position “P”.

Notes: For improved recognition of the KEYLESS-GO-card the doors should be closed when pressing the start-/stop button. The gear selector lever can only be moved with the vehicle battery charged and connected, and the starter switch in the Operation position. With the gear selector lever in position “P”, the brake pedal must also be depressed.

Important! For the KEYLESS-GO-system to function properly, the operator should observe the following: • If the KEYLESS-GO-card is positioned farther away from the vehicle (e.g. inside clothing or a briefcase), the vehicle cannot be locked (see page 39) or started with the start-/stop button (see page 234).

• If the KEYLESS-GO-card is removed from the vehicle

while the engine is running and a door opened, or by placing the card in front of the center armrest (see page 195), the message “CHIP-CARD – NOT RECOGNIZED!” will appear intermittent in the multifunction display, see page 37.

Starter switch — KEYLESS-GO

231

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 232 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Starter switch — KEYLESS-GO

232

• Do not forget, the engine can be started by anyone if

a KEYLESS-GO-card is left inside the vehicle.

• To be able to operate the vehicle in the case of a

malfunction in the KEYLESS-GO-system (e.g. strong radio frequency disturbance), we recommend that you carry the electronic key plus mechanical key with you and keep them in a safe place so that they are always handy. Never leave the electronic key in the vehicle.

• To avoid radio transmission interference, never store the KEYLESS-GO-card together with other electronic items (e.g. cellular telephones, other KEYLESS-GO- cards) or metallic objects (e.g. coins, metal foil).

Notes: With the engine at idle speed, the charging rate of the alternator (output) is limited. It is therefore recommended that you turn off unnecessary electrical consumers while driving in stop- and-go traffic. This precaution helps to avoid draining of the battery. Unnecessary strain on the battery and charging system may be minimized by turning off the following power consumers, for example: Heated seats, rear window defroster. In addition, the automatic climate air volume control should be set to the lowest position.

J_OM_215.book Seite 233 Mittwoch, 30. Mai 2001 2:01 14

Starting and turning off the engine

Before starting Ensure that parking brake is engaged and that selector lever is in position “P” or “N”.

Important! In areas where temperatures frequently drop below -4°F (-20°C) we recommend that an engine block heater be installed. Your authorized Mercedes-Benz Center will advise you on this subject, see page 253.

Starting with the electronic key Do not depress accelerator. Turn electronic key in starter switch to position 2. Briefly turn electronic key in starter switch clockwise to the stop and release. The starter will engage until the engine is running. If engine will not run, and the starting procedure stops, turn electronic key completely to the left and repeat starting the engine.

After several unsuccessful attempts, have the system checked at the nearest authorized Mercedes-Benz Center.

Important! Due to the installed starter non-repeat feature, the electronic key must be turned completely to the left before attempting to start the engine again.

Turning off with the electronic key Put the selector lever in position “P” and turn the electronic key in the starter switch to position 0 to stop the engine. The electronic key can only be removed with the selector lever in position “P”.

Starting and turning off the engine

233

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 234 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Starting and turning off the engine

234

Starting with KEYLESS-GO

Note: For improved recognition of the chip card the doors should be closed when pressing the start-/stop button.

Depress brake pedal during the starting procedure. Do not depress accelerator. Briefly press start-/stop button on gear selector lever. The starter will engage until the engine is running. If engine will not run, and the starting procedure stops, press start-/stop button on gear selector lever and repeat starting the engine. After several unsuccessful attempts, have the system checked at the nearest authorized Mercedes-Benz Center.

Turning off with KEYLESS-GO Stop the vehicle and put the selector lever in position “P”. Press start-/stop button on the selector lever until the engine stops. With the driver’s door closed the starter switch is set to the “On” position (starter switch position 1). With the driver’s door opened the starter switch is set to the “Off” position (starter switch position 0, same as electronic key removed from starter switch).

Note: The engine can only be turned off with selector lever in position “P”. If attempting to turn off the engine while the selector lever is in any other position than “P” a signal sounds and the message “SELECTOR LEVER TO P” appears in the multifunction display as a reminder to move the selector to position “P”.

J_OM_215.book Seite 235 Mittwoch, 30. Mai 2001 2:01 14

Automatic transmission

The automatic transmission selects individual gears automatically, dependent upon • Selector lever position, see page 238
• Program mode selector, see page 242
• Accelerator position • Vehicle speed The gear shifting process is continuously adapted, dependent on the driving style, the driving situation and the road characteristics.

Important! When parking the vehicle or before working on the vehicle with the engine running, firmly depress the parking brake pedal and shift the selector lever into “P”.

Automatic transmission

235

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 236 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic transmission

236

Driving The selector lever is automatically locked while in position “P”. To move the selector lever out of position “P”, the service brake pedal must be firmly depressed before the shift lock will release. Shift selector lever to the desired position only when the engine is idling normally and the service brake is applied. Do not release the brake until ready to drive. The vehicle may otherwise start creeping when the selector lever is in drive or reverse position.

Warning! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and when your right foot is firmly on the brake pedal.

Important! After selecting any driving position from “N” or “P”, wait a moment to allow the gear to fully engage before accelerating, especially when the engine is cold.

Accelerator position Partial throttle = early upshifting = normal acceleration Full throttle = later upshifting = rapid acceleration Kickdown (depressing the accelerator beyond full throttle) = downshifting to a lower gear = maximum acceleration. Once the desired speed is attained, ease up on the accelerator — the transmission shifts up again.

J_OM_215.book Seite 237 Mittwoch, 30. Mai 2001 2:01 14

Stopping For brief stops, e.g. at traffic lights, leave the transmission in gear and hold vehicle with the service brake. For longer stops with the engine idling, shift into “N” or “P” and hold the vehicle with the service brake. When stopping the vehicle on an uphill gradient, do not hold it with the accelerator, use the brake. This avoids unnecessary transmission heat build up.

Maneuvering To maneuver in tight areas, e.g. when pulling into a parking space, control the vehicle speed by gradually releasing the brakes. Accelerate gently and never abruptly step on the accelerator. To rock a vehicle out of soft ground (mud or snow), alternately shift from forward to reverse, while applying slight partial throttle.

Rocking a vehicle free in this manner may cause the ABS or traction system malfunction indicator lamp to come on. Turn off and restart the engine to clear the malfunction indication.

Warning! Getting out of your vehicle with the selector lever not fully engaged in position “P” is dangerous. Also, when parked on an incline, position “P” alone may not prevent your vehicle from moving, possibly hitting people or objects. Always set the parking brake in addition to shifting to position “P”, see page 244 for parking brake. When parked on an incline, also turn front wheel against curb.

Warning! When leaving the vehicle always remove the electronic key from the starter switch, take the KEYLESS-GO-card (if so equipped) with you and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could move the gear selector lever from position “P”, which could result in an accident or serious injury.

Automatic transmission

237

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 238 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic transmission

238

Selector lever position

The current selector lever position is indicated in the gear range indicator display. The automatic gear shifting process can be adapted to specific operating conditions using the selector lever.

Park position The park position is to be used when parking the vehicle. Engage only with the vehicle stopped. The park position is not intended to serve as a brake when the vehicle is parked. Rather, the driver should always use the parking brake in addition to placing the selector lever in park to secure the vehicle. Note: The electronic key can only be removed from the starter switch with the selector lever in position “P”. With the electronic key removed, the selector lever is locked in position “P”. Reverse gear Shift to reverse gear only with the vehicle stopped. Dependent on the program mode selector switch position “S” or “W” the maximum speed in the reverse gear is different. However, it is not possible to change the program mode while in reverse.

J_OM_215.book Seite 239 Mittwoch, 30. Mai 2001 2:01 14

Neutral No power is transmitted from the engine to the drive axle. When the brakes are released, the vehicle can be moved freely (pushed or towed). Do not engage “N” while driving except to coast when the vehicle is in danger of skidding (e.g. on icy roads, see page 252 for winter driving instructions). Important! Coasting the vehicle, or driving for any other reason with selector lever in “N” can result in transmission damage that is not covered by the Mercedes-Benz Limited Warranty. The transmission automatically upshifts through 5th gear. Position “D” provides optimum driving characteristics under all normal operating conditions.

Gear selection for special circumstances The transmission gear ranges for special circumstances can be selected by pressing the selector lever to the right or the left with the selector lever in position “D”. The gear range currently selected is indicated in the instrument cluster display. Briefly press selector lever in the “D –” direction: The transmission will shift from the current gear range to the next lower gear range. Press and hold selector lever in the “D –” direction: The selector lever position display will switch to the gear range currently selected by the automatic transmission. Shifting into another gear range that allows for quicker acceleration or to slow the vehicle down is possible. Downshifts can also be performed.

Note: To avoid overrevving the engine when the selector lever is moved in “D –” direction, the transmission will not shift to a lower gear if the engine’s revolutions per minute limit would be exceeded.

Automatic transmission

239

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 240 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic transmission

240

Briefly press selector lever in the “D +” direction: The transmission will shift from the current gear range to the next higher gear range. If the transmission is already in gear range “D”, an additional upshift of one gear is possible. Press and hold selector lever in the “D +” direction: The transmission will shift from the current gear directly to gear range “D”.

Warning! On slippery road surfaces, never downshift in order to obtain braking action. This could result in drive wheel slip and reduced vehicle control. Your vehicle’s ABS will not prevent this type of loss of control.

Important! With transmission in gear range “D”, “4” or “3”, upshifting from 1st to 2nd to 3rd gear is delayed depending on vehicle speed and engine temperature. This allows the catalytic converter to heat up more quickly to operating temperatures. During the brief warm-up period this delayed upshift and increased engine noise might be perceived as a

malfunction. However, neither the engine nor transmission are negatively affected by this mode of operation. The delayed upshift is effective with vehicle speeds below 31 mph (50 km/h) at partial throttle and engine temperatures below 95°F (35°C). To avoid overrevving the engine when the selector lever is moved to a lower gear range, the transmission will not shift to a lower gear, if the engine’s revolutions per minute limit would be exceeded. In this case there will be no downshift, even when the vehicle speed reaches the engine’s rpm limit of that gear, e.g. by applying the service brakes. To prevent the engine from laboring at low RPM when driving uphill gradients or with your vehicle heavily loaded, the automatic transmission will downshift when necessary to maintain engine RPM within the best torque range.

J_OM_215.book Seite 241 Mittwoch, 30. Mai 2001 2:01 14

Gear ranges:

Upshift through 4th gear only. Suitable for performance driving. Upshift through 3rd gear only. Suitable for moderately steep hills. Since the transmission does not shift higher than 3rd gear, this gear selection will allow use of the engine’s braking power downhill.

Upshift through 2nd gear only. For driving in mountainous regions or under extreme operating conditions. This gear selection will allow use of the engine’s braking power when descending steep grades. Use this position, which makes maximum use of the engine’s braking effect, while descending very steep or lengthy downgrades and only at speeds below 40 mph (60 km/h).

Automatic transmission

241

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 242 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Automatic transmission

Program mode selector switch

242

The transmission is provided with a selector switch (1) for Standard “S” and Winter/Wet (snow and ice) “W” program modes. The program mode currently selected is indicated in the gear range indicator display.

Standard mode Press switch on symbol “S”. Use this mode for all regular driving. The vehicle starts out in 1st gear. Accelerator Operation: Fast on = depressing the accelerator pedal quickly (not into kickdown position) while driving continuously, rather than depressing the accelerator pedal in the usual manner, will cause the automatic transmission to shift down into a lower gear. This gear shifting process is dependent on the current vehicle speed. Fast off = there will be no upshift when releasing the accelerator pedal quickly, e.g. using the engine’s braking power during performance driving.

J_OM_215.book Seite 243 Mittwoch, 30. Mai 2001 2:01 14

W Winter/Wet (snow and ice) mode

Press switch on symbol “W”. The vehicle starts out in 2nd gear, except with selector lever in 1st gear, or with accelerator pedal in kick-down position. The “W” mode helps to improve traction and driving stability of the vehicle. The gear shifting process occurs at lower vehicle and engine speeds than in the “S” program mode.

Caution! Never change the program mode when the selector lever is out of position “P”. It could result in a change of driving characteristics for which you may not be prepared.

Important! Always be certain of the program mode selected since the vehicle driving characteristics change with the selection of the program mode. Dependent on the program mode selector switch position “S” or “W” and the gear selector lever in position “R”, the ratio of power transmission changes.

Emergency operation (Limp home mode) If vehicle acceleration worsens or the transmission no longer shifts, the transmission is most likely operating in Limp Home Mode which engages when there is a malfunction of the transmission. This condition may be accompanied by the “CHECK ENGINE” malfunction indicator lamp in the instrument cluster coming on. In this mode only the 2nd gear or reverse gear can be activated. To engage 2nd gear or reverse:

1. Stop the vehicle. 2. Move selector lever to position “P”. 3. Turn off the engine. 4. Wait approx. 10 seconds. 5. Restart the engine. 6. Move selector lever to position “D” (for 2nd gear), or move selector lever to position “R” (for reverse gear).

Have the transmission checked at your authorized Mercedes-Benz Center as soon as possible.

Automatic transmission

243

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 244 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Parking brake

Parking brake

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

244

To engage, firmly depress parking brake pedal. When the electronic key is in starter switch position 2, the brake warning lamp in the instrument cluster should come on brightly. To release the parking brake, pull handle on instrument panel. The brake warning lamp in the instrument cluster should go out. A warning sounds and the parking brake warning message (see page 308) appears in the multifunction display, if you start to drive without having released the parking brake. Also see brake warning lamp on page 298.

Warning! When leaving the vehicle always remove the electronic key from the starter switch, take the KEYLESS-GO-card (if so equipped) with you and lock the vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Children could release the parking brake, which could result in an accident or serious injury.

J_OM_215.book Seite 245 Mittwoch, 30. Mai 2001 2:01 14

Driving instructions

Drinking and driving

Drive sensibly – save fuel Fuel consumption, to a great extent, depends on driving habits and operating conditions. To save fuel you should: • keep tires at the recommended inflation pressures. • remove unnecessary loads, • remove roof rack when not in use, • allow engine to warm up under low load use, • avoid frequent acceleration and deceleration, • have all maintenance work performed at regular intervals by an authorized Mercedes-Benz Center. Fuel consumption is also increased by driving in cold weather, in stop-and-go traffic, on short trips and in hilly country.

Warning! Drinking or taking drugs and driving can be a very dangerous combination. Even a small amount of alcohol or drugs can affect your reflexes, perceptions and judgement. The possibility of a serious or even fatal accident is sharply increased when you drink or take drugs and drive. Please don’t drink or take drugs and drive or allow anyone to drive after drinking or taking drugs.

Pedals

Warning! Keep driver’s foot area clear at all times. Objects stored in this area may impair pedal movement.

Driving instructions

245

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 246 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Driving instructions

Power assistance

246

Warning! When the engine is not running, the brake and steering systems are without power assistance. Under these circumstances, a much greater effort is necessary to stop or steer the vehicle.

Brakes

Warning! After driving in heavy rain for some time without applying the brakes or through water deep enough to wet brake components or salty road conditions, the first braking action may be somewhat reduced and increased pedal pressure may be necessary to obtain expected braking effect. Be sure to maintain a safe distance from vehicles in front. Resting your foot on the brake pedal will cause excessive and premature wear of the brake pads. It can also result in the brakes overheating thereby significantly reducing their effectiveness. It may not be possible to stop the vehicle in sufficient time to avoid an accident.

Excessive use of salt and other snow melting chemicals spread on roads during the winter months may cause a build up of moisture or residue to form on the braking components. This build up or residue could cause light corrosion of the braking components if the vehicle is parked with the brakes cold. Apply steady and even braking pressure when stopping the vehicle to warm up and dry the brake components.

Important! Please pay attention to the function of the brake assist system (BAS), see page 275.

The condition of the parking brake system is checked each time the vehicle is in the shop for the required maintenance service at an authorized Mercedes-Benz Center. If the parking brake is released and the brake warning lamp in the instrument cluster stays on, the brake fluid level in the reservoir is too low. Brake pad wear or a leak in the system may be the reason for low brake fluid in the reservoir. Have the brake system inspected at an authorized Mercedes-Benz Center immediately.

J_OM_215.book Seite 247 Mittwoch, 30. Mai 2001 2:01 14

All checks and service work on the brake system should be carried out by an authorized Mercedes-Benz Center. Install only brake pads and brake fluid recommended by Mercedes-Benz.

Warning! If other than recommended brake pads are installed, or other than recommended brake fluid is used, the braking properties of the vehicle can be degraded to an extent that safe braking is substantially impaired. This could result in an accident.

Caution! When driving down long and steep grades, relieve the load on the brakes by shifting into a lower gear to use the engine’s braking power. This helps prevent overheating of the brakes and reduces brake pad wear. After hard braking, it is advisable to drive on for some time, rather than immediately parking, so the air stream will cool down the brakes faster.

Driving off Apply the service brakes to test them briefly after driving off. Perform this procedure only when the road is clear of other traffic. Warm up the engine smoothly. Do not place full load on the engine until the operating temperature has been reached. When starting off on a slippery surface, do not allow one drive wheel to spin for an extended period with the ESP switched off. Doing so may cause serious damage to the drive train which is not covered by the Mercedes-Benz Limited Warranty.

Driving instructions

247

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 248 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

248

Important! It is advisable to set the parking brake whenever parking or leaving the vehicle. In addition, move selector lever to position “P”. When parking on hills, always set the parking brake.

Driving instructions

Parking

Warning! To reduce the risk of personal injury as a result of vehicle movement, before turning off the engine and leaving the vehicle always: 1. Keep right foot on service brake pedal. 2. Firmly depress parking brake pedal. 3. Move the selector lever to position “P”. 4. Slowly release service brake pedal. 5. Turn front wheels towards the road curb. 6. Turn the electronic key to starter switch

position 0 and remove, or press start-/stop button (vehicles with KEYLESS-GO).

7. Take the electronic key and the KEYLESS-GO-

card (vehicles with KEYLESS-GO) and lock vehicle when leaving.

J_OM_215.book Seite 249 Mittwoch, 30. Mai 2001 2:01 14

Tires

Warning! If you feel a sudden significant vibration or ride disturbance, or you suspect that possible damage to your vehicle has occurred, you should turn on the hazard warning flashers, carefully slow down, and drive with caution to an area which is a safe distance from the roadway. Inspect the tires and under the vehicle for possible damage. If the vehicle or tires appear unsafe, have it towed to the nearest Mercedes-Benz Center or tire dealer for repairs.

Tread wear indicators (TWI) are required by law. These indicators are located in six places on the tread circumference and become visible at a tread depth of approximately 1/16 in (1.5 mm), at which point the tire is considered worn and should be replaced. The tread wear indicator appears as a solid band across the tread.

Warning! Do not allow your tires to wear down too far. As tread depth approaches 1/16 in (1.5 mm), the adhesion properties on a wet road are sharply reduced. Depending upon the weather and/or road surface (conditions), the tire traction varies widely.

Specified tire pressures must be maintained. This applies particularly if the tires are subjected to high loads (e.g. high speeds, heavy loads, high ambient temperatures).

Warning! Do not drive with a flat tire. A flat tire affects the ability to steer or brake the vehicle. You may lose control of the vehicle. Continued driving with a flat tire or driving at high speed with a flat tire will cause excessive heat build-up and possibly a fire.

Driving instructions

249

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 250 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Driving instructions

250

Aquaplaning Depending on the depth of the water layer on the road, aquaplaning may occur, even at low speeds and with new tires. Reduce vehicle speed, avoid track grooves in the road and apply brakes cautiously in the rain.

Tire traction The safe speed on a wet, snow covered or icy road is always lower than on a dry road. You should pay particular attention to the condition of the road whenever the outside temperatures are close to the freezing point.

Warning! If ice has formed on the road, tire traction will be substantially reduced. Under such weather conditions, drive, steer and brake with extreme caution.

We recommend M+S rated radial-ply tires for the winter season for all four wheels to insure normal balanced handling characteristics. On packed snow, they can reduce your stopping distance as compared with summer tires. Stopping distance, however, is still considerably greater than when the road is not snow or ice covered.

Tire speed rating CL 500 and CL 600: Your vehicle is factory equipped with “H”-rated tires, which have a speed rating of 130 mph (210 km/h). Vehicles with Sport Package: Your vehicle is factory equipped with “Y”-rated tires, which have a speed rating of 188 mph (300 km/h). An electronic speed limiter prevents your vehicle from exceeding a speed of 130 mph (210 km/h).

J_OM_215.book Seite 251 Mittwoch, 30. Mai 2001 2:01 14

CL 55 AMG: Your vehicle is factory equipped with “Y”-rated tires, which have a speed rating of 188 mph (300 km/h). An electronic speed limiter prevents your vehicle from exceeding a speed of 155 mph (250 km/h). Despite the tire rating, local speed limits should be obeyed. Use prudent driving speeds appropriate to prevailing conditions.

Warning! Even when permitted by law, never operate a vehicle at speeds greater than the maximum speed rating of the tires. Exceeding the maximum speed for which tires are rated can lead to sudden tire failure causing loss of vehicle control and resulting in personal injury and possible death.

Snow chains Use only snow chains that are tested and recommended by Mercedes-Benz. Your authorized Mercedes-Benz Center will be glad to advise you on this subject. Chains should only be used on the rear wheels. Follow the manufacturer’s mounting instructions. Always select option I or II of the level control system when driving with snow chains, see page 283. Snow chains should only be driven on snow covered roads at speeds not to exceed 30 mph (50 km/h). Remove chains as soon as possible when driving on roads without snow. When driving with snow chains, press the ESP control switch to OFF, refer to page 280.

Important! Use of snow chains is not permissible with tire sizes 245/45 R18 or 275/40 R18.

Driving instructions

251

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 252 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Driving instructions

252

Winter driving instructions The most important rule for slippery or icy roads is to drive sensibly and to avoid abrupt acceleration, braking and steering maneuvers. Do not use the cruise control system under such conditions. When the vehicle is in danger of skidding, move selector lever to position “N”. Try to keep the vehicle under control by corrective steering action. Road salts and chemicals can adversely affect braking efficiency. Increased pedal force may become necessary to produce the normal brake effect. We therefore recommend depressing the brake pedal periodically when traveling at length on salt-strewn roads. This can bring road salt impaired braking efficiency back to normal. A prerequisite is, however, that this be done without endangering other drivers on the road.

If the vehicle is parked after being driven on salt treated roads, the braking efficiency should be tested as soon as possible after driving is resumed while observing the safety rules in the previous paragraph.

Warning! If the vehicle becomes stuck in snow, make sure that snow is kept clear of the exhaust pipe and from around the vehicle with engine running. Otherwise, deadly carbon monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death. To assure sufficient fresh air ventilation, open a window slightly on the side of the vehicle not facing the wind.

J_OM_215.book Seite 253 Mittwoch, 30. Mai 2001 2:01 14

Winter driving Have your vehicle winterized at your authorized Mercedes-Benz Center before the onset of winter. • Change the engine oil if the engine contains an oil

which is not approved for winter operation. For viscosity (SAE/CCMC class) and filling quantity, see page 401.

• Check engine coolant anticorrosion/antifreeze

concentration.

• Additive for the windshield washer and headlamp

cleaning system: Add MB Concentrate “S” to a premixed windshield washer solvent/antifreeze which is formulated for below freezing temperatures, see page 340.

• Test battery: Battery capacity drops with decreasing ambient temperature. A well charged battery helps to ensure that the engine can be started, even at low ambient temperatures.

• Tires: We recommend M+S rated radial-ply tires on

all four wheels for the winter season. Observe permissible maximum speed for M+S rated radial-ply tires and the legal speed limit.

In winter operation, the maximum effectiveness of the ABS and ESP can only be achieved with M+S rated radial-ply tires and/or snow chains recommended by Mercedes-Benz. Snow chains maximize performance.

Block heater (Canada only) The engine is equipped with a block heater. The electrical cable may be installed at your authorized Mercedes-Benz Center.

Driving instructions

253

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 254 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Driving instructions

Deep water

254

Passenger compartment

Caution! Do not drive through flooded areas or water of unknown depth. If you must drive through deep water, drive slowly to prevent water from entering the engine compartment or passenger compartment, being ingested by the air intake, possibly causing damage to electrical components or wiring, to engine or transmission that is not covered by the Mercedes-Benz Limited Warranty.

Warning! Always fasten items being carried as securely as possible. In an accident, during hard braking or sudden maneuvers, loose items will be thrown around inside the vehicle, and cause injury to vehicle occupants unless the items are securely fastened in the vehicle. The trunk is the preferred place to carry objects.

J_OM_215.book Seite 255 Mittwoch, 30. Mai 2001 2:01 14

Traveling abroad Abroad, there is a widely-spread Mercedes-Benz service network at your disposal. If you plan to travel into areas which are not listed in the index of your Mercedes-Benz Center directory, you should request pertinent information from your authorized Mercedes-Benz Center. Driving in countries with left-hand traffic requires the headlamps to be switched over accordingly, see page 368.

Driving instructions

255

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

J_OM_215.book Seite 256 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Driving systems

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Cruise control

The cruise control allows you to drive in a more relaxed manner, for example over long distances, as it automatically maintains the set speed by actively regulating the throttle setting. Any given speed above approximately 25 mph (40 km/h) can be maintained with the cruise control by operating the lever.

1 Accelerate and set:

Lift lever briefly to set speed. Hold lever up to accelerate.

256

2 Decelerate and set:

Depress lever briefly to set speed. Hold lever down to decelerate. Normally the vehicle is accelerated to the desired speed with the accelerator. Speed is set by briefly pushing the lever to position 1 or 2. The accelerator can then be released. The selected speed is shown for approx. 5 seconds in the multifunction display, and the corresponding speedometer segments from the selected speed to the vehicle maximum speed are illuminated. The speed can be increased (e.g. for passing) by using the accelerator. After the accelerator is released, the previously set speed will be resumed automatically. If a set speed is to be increased or decreased slightly, e.g. to adapt to the traffic flow, hold lever in position 1 or 2 until the desired speed is reached, or briefly tip the lever in the appropriate direction for increases or decreases in 0.6 mph (1 km/h) increments. When the lever is released, the newly set speed remains.

J_OM_215.book Seite 257 Mittwoch, 30. Mai 2001 2:01 14

3 Canceling

4 Resume

To cancel the cruise control, briefly push lever to position 3. When you step on the brake pedal or the vehicle speed drops below approx. 25 mph (40 km/h), for example when driving upgrade, the cruise control will be canceled. If the illuminated speedometer segments begin to blink (e.g. when aquaplaning or when moving the gear selector lever to position “N” while driving), the cruise control is automatically switched off. If the cruise control cancels by itself and remains inoperative until the engine is restarted, have the system checked at your authorized Mercedes-Benz Center as soon as possible.

If the lever is briefly pushed to position 4 when driving at a speed exceeding approx. 25 mph (40 km/h), the vehicle resumes the speed which was set prior to the cancellation of the cruise control. The selected speed is shown for approx. 5 seconds in the multifunction display, and the corresponding speedometer segments from the selected speed to the vehicle maximum speed are illuminated. The last memorized speed is canceled when the electronic key in the starter switch is turned to position 1 or 0.

Important! Moving gear selector lever to position “N” switches the cruise control off.

Driving systems

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

257

J_OM_215.book Seite 258 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Driving systems

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Warning! Only use the cruise control if the traffic and weather conditions make it advisable to travel at a steady speed.

• The use of cruise control can be dangerous on

winding roads or in heavy traffic because conditions do not allow safe driving at a steady speed.

• The use of cruise control can be dangerous on slippery roads. Rapid changes in tire adhesion can result in wheel spin and loss of control.

The “Resume” function should only be operated if the driver is fully aware of the previously set speed and wishes to resume this particular preset speed.

258

Notes: If the engine does not brake the vehicle sufficiently while driving on a downgrade, the speed you set on the cruise control may be exceeded. In this case the automatic transmission shifts down (max. to 3rd gear) to maintain the set cruise control speed by using the engine’s braking power. As soon as the grade eases, the automatic transmission shifts up again dependent on the selector lever position. Nevertheless, in some cases you may have to step on the brake pedal to slow down. In this case the cruise control is switched off. Use the lever to resume the previously set speed. The “CRUISE CONTROL - - -” message is displayed on the multifunction display when any attempt is made to store speeds below 25 mph (40 km/h) or when an attempt is made to recall a speed when no speed has been stored – the cruise control remains switched off. See malfunction and warning messages on page 303 if the cruise control has a malfunction.

J_OM_215.book Seite 259 Mittwoch, 30. Mai 2001 2:01 14

Distronic (DTR) (optional) When activated the Distronic system increases driving convenience, for example over long distances, as it automatically maintains a speed set by the driver by actively regulating the throttle setting. It also maintains within certain limitations a preset distance to a vehicle ahead. With Distronic switched off, the multifunction display continues to show the distance to the vehicle ahead, if so selected, see page 273. The distance warning function can be activated separately, see page 270. In Distronic mode, if the distance sensor detects a slower moving vehicle directly ahead, your vehicle speed will be reduced to the extent permitted by reduced throttle and up to 20% of vehicle braking power, so that you follow that vehicle at a preset distance, see page 271. Maximum range of detection is approximately 500 ft. (150 m).

Any given speed between 25 mph (Canada: 40 km/h) and 110 mph (Canada: 180 km/h) can be maintained with the Distronic by operating the control lever on the steering column.

Warning! Distronic is a convenience system, its speed adjustment reduction capability is intended to make cruise control more effective and usable when traffic speeds vary. It is not, however, intended to nor does it replace the need for extreme care. The responsibility for the vehicle speed and the distance to the vehicle ahead, including most importantly brake operation to assure safe stopping distance, rests always with the driver. Distronic cannot take street and traffic conditions into account.

Warning! Distronic requires familiarity with its operational characteristics. We strongly recommend that you review the following information carefully before operating the system.

Driving systems

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

259

J_OM_215.book Seite 260 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Driving systems

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Note: For operation in the USA only: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any unauthorized modification to this device could void the user’s authority to operate the equipment.

260

. Warning! Only use Distronic if the traffic and weather conditions make it advisable to travel at a steady speed. Use of Distronic can be dangerous on winding roads or in heavy traffic because conditions do not allow safe driving at a steady speed. Use of Distronic can be dangerous on slippery roads. Rapid changes in tire adhesion can result in wheel spin and loss of control. Distronic does not act upon adverse sight distance conditions. Do not use Distronic during conditions of fog and heavy rain, snow or sleet. The “Resume” function should only be operated if the driver is fully aware of the previously set speed and wishes to resume this particular preset speed. Distronic does not recognize accordingly and will not react to stationary objects. It is designed and intended only to maintain a set speed and keep a set distance from moving objects in front of it.

J_OM_215.book Seite 261 Mittwoch, 30. Mai 2001 2:01 14

The speed stored in memory is displayed in the multifunction display, and one or two segments around the stored speed light up in the speedometer dial, see page 274.

1 Accelerate and set:

To increase the speed by 5 mph (Canada: 10 km/h) – briefly lift lever up. 2 Decelerate and set:

To reduce the speed by 5 mph (Canada: 10 km/h) – briefly depress lever.

3 Canceling

To cancel Distronic, briefly push lever to position 3. The last set speed remains stored in memory.

4 Resume

• If the lever is briefly pulled to position 4 when

driving at a speed above approx. 25 mph (Canada: 40 km/h), the vehicle resumes the speed which was selected prior to the cancellation of Distronic.

• For minor increases of speeds in increments of 1 mph (Canada: 1 km/h) – briefly pull lever to position 4.

The last memorized speed is canceled when the electronic key in the starter switch is turned to position 1 or 0.

Driving systems

Instruments and controls

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

261

J_OM_215.book Seite 262 Mittwoch, 30. Mai 2001 2:01 14

Instruments and controls

Driving systems

Operation

Driving

Instrument cluster display

Practical hints

Car care

Technical

data

Index

Activation of Distronic

Any given speed above approximately 25 mph (Canada: 40 km/h) can be maintained: • Normally the vehicle is accelerated to the desired

speed with the accelerator.

262

• Speed is set by briefly moving the control lever to

position 1 or 2. The stored speed is displayed in the multifunction display for approx. 5 seconds (see also page 273), and one or two segments around the stored speed light up on the speedometer dial (see also page 274).

• Remove foot from the accelerator.