worn at all times while the vehicle is in motion. The airbags deploy only in certain side impact conditions severe enough to cause significant injury to the vehicle occupants.
1FEATURES OF YOUR HYUNDAI
46
B240C02JM-AAT
SRS Care o The SRS is virtually maintenance free and there are no parts you can safely service by yourself. If the SRS SRI (Ser- vice Reminder Indicator) does not illu- minate, or continuously remains on, have your vehicle immediately in- spected by your Hyundai dealer.
o Any work on the SRS system, such as removing, installing, repairing, or any work on the steering wheel must be performed by a qualified Hyundai tech- nician. Improper handling of the airbag system may result in serious personal injury.
! WARNING:
o Do not install a child restraint system in the front passenger seat position. A child restraint system must never be placed in the front seat. The infant or child could be severely injured or killed by an airbag deployment in case of an accident.
o Modification to SRS components or wir-ing, including the addition of any kind of badges to the pad covers or modifications to the body structure, can adversely affect SRS perfor- mance and lead to possible injury.
! WARNING:
o For cleaning the airbag pad covers, use only a soft, dry cloth or one which has been moistened with plain water. Solvents or cleaners could adversely affect the airbag covers and proper deployment of the system.
o No objects should be placed over or near the airbag modules on the steer- ing wheel, instrument panel, and the front passenger's panel above the glove box, because any such object could cause harm if the vehicle is in a crash severe enough to cause the airbags to inflate.
o If the airbags inflate, they must be replaced by an authorized Hyundai dealer.
o Do not tamper with or disconnect SRS wiring, or other components of the SRS system. Doing so could result in injury, due to accidental inflation of the airbags or by rendering the SRS inoperative.
WARNING:
o If components of the airbag system must be discarded, or if the vehicle must be scrapped, certain safety pre- cautions must be observed. Your Hyundai dealer knows these precau- tions and can give you the necessary information. Failure to follow these precautions and procedures could increase the risk of personal injury. o If your car was flooded and has soaked carpeting or water on the floor, don't try to start the engine; have the car towed to an authorized Hyundai dealer. o Do not replace the bumper or the bumper guard with the one other than the Hyundai genuine parts. Otherwise, it can adversely affect SRS perfor- mance and lead to an increased risk of injury.
B240D02JM-AAT
Additional Safety Precautions o Never let passengers ride in the cargo area (trunk) or on top of a folded-down back seat. All occupants should sit upright, fully back in their seats with their seat belts on and their feet on the floor.
o Passengers should not move out of or change seats while the vehicle is mov- ing. A passenger who is not wearing a seat belt during a crash or emergency stop can be thrown against the inside of the vehicle, against other occupants, or out of the vehicle.
o Each seat belt is designed to restrain one occupant. If more than one person uses the same seat belt, they could be seriously injured or killed in a collision. o Do not use any accessories on seat belts. Devices claiming to improve oc- cupant comfort or reposition the seat belt can reduce the protection provided by the seat belt and increase the chance of serious injury in a crash.
o Passengers should not place hard or sharp objects between themselves and the airbags. Carrying hard or sharp objects on your lap or in your mouth can result in injuries if an airbag inflates.
FEATURES OF YOUR HYUNDAI
47
! WARNING:
o Sitting improperly or out of position can cause occupants to be shifted too close to a deploying airbag, strike the interior structure or be thrown from the vehicle resulting in serious injury or death.
o Always sit upright with the seatback in an upright position, centered on the seat cushion with your seat belt on, legs comfortably extended and your feet on the floor.
Adding Equipment to or Modifying Your Airbag-Equipped Vehicle. If you modify your vehicle by changing your vehicle's frame, bumper system, front end or side sheet metal or ride height, this may affect the operation of your vehicle's airbag system.
o Keep occupants away from the airbag covers. All occupants should sit up- right, fully back in their seats with their seat belts on and their feet on the floor. If occupants are too close to the airbag covers, they could be injured if the airbags inflate.
o Do not attach or place objects on or near the airbag covers. Any object attached to or placed on the front or side impact airbag covers could interfere with the proper operation of the airbags. o Do not modify the front seats. Modifi- cation of the front seats could interfere with the operation of the supplemental restraint system sensing components or side impact airbags.
o Do not place items under the front seats. Placing items under the front seats could interfere with the operation of the supplemental restraint system sensing components and wiring har- nesses.
o Never hold an infant or child on your lap. The infant or child could be seri- ously injured or killed in the event of a crash. All infants and children should be properly restrained in appropriate child safety seats or seat belts in the rear seat.
1FEATURES OF YOUR HYUNDAI
48
INSTRUMENT CLUSTER AND INDICATOR LIGHTS
B260A02JM-AAT
2 3 4
6 7 2 8 9
10
11
12 13 14
15
16
17
18
19
20
22
24 25 26
21
23
OJM019016-U
FEATURES OF YOUR HYUNDAI
49
1. Tachometer 2. Turn Signal Indicator Light 3. Seat Belt Warning Light 4. Supplemental Restraint (AirBag) System
Service Reminder Indicator (SRI)
5. Speedometer 6. Parking Brake/Low Brake Fluid Level Warning Light 7. Low Oil Pressure Warning Light 8. High Beam Indicator Light 9. Engine Temperature Warning Light 10. Fuel Gauge 11. Tail Gate Open Warning Light 12. Traction Control Indicator Light (If installed)/
Electronic Stability Control (ESC) Indicator Light (If installed)
13. ABS Service Reminder Indicator (If installed) 14. Immobilizer Warning Light (If installed) 15. Door Ajar Warning Light 16. Automatic Transaxle Position Indicator Light (If installed) 17. Odometer/ Trip odmeter 18. Trip Computer (If installed) 19. Malfunction Indicator Light (MIL) 20. Charging System Warning Light 21. Low Tire Pressure Telltale (If installed) 22. 4WD System Warning Light (If installed) 23. TPMS (Tire Pressure Monitoring System) Malfunction Indicator
(If installed)
24. 4WD Lock Indicator Light 25. Cruise Indicator (If installed) 26. Low Fuel Warning Light
1FEATURES OF YOUR HYUNDAI
50
WARNING AND INDICATOR LIGHTS
B260B01JM-AAT
SRS (Airbag) Service Reminder Indicator (SRI)
B260E02O-AAT
Seat Belt Reminder Light and Chime
B260G01A-AAT
Low Oil Pressure Warning Light
The SRS service reminder indicator (SRI) comes on for about 6 seconds after the ignition key is turned to the "ON" position or after the engine is started, after which it will go out.
The seat belt reminder light blinks until your seat belt is fastened when the ignition key is turned from the "OFF" position to "ON" or "START" and the warning chime will sound for 6 seconds.
B260F01A-AAT
High Beam Indicator Light
The high beam indicator light comes on whenever the headlights are switched to the high beam or flash position.
This light also comes on when the SRS is not working properly. If the SRI does not come on, or continuously remains on after coming on for about 6 seconds when you turned the ignition key to the "ON" position or started the engine, or if it comes on while driving, have the SRS inspected by an authorized Hyundai Dealer.
B260D01A-AAT
Turn Signal Indicator Lights
The blinking green arrows on the instru- ment panel show the direction indicated by the turn signals. If the arrow comes on but does not blink, blinks more rapidly than normal, or does not illuminate at all, a malfunction in the turn signal system is indicated. Your dealer should be consulted for repairs.
CAUTION:
If the low oil pressure warning light stays on while the engine is running, serious engine damage may result. The oil pres- sure warning light comes on whenever there is insufficient oil pressure. In nor- mal operation, it should come on when the ignition switch is turned on, then go out when the engine is started. If the oil pressure warning light stays on while the engine is running, there is a serious malfunction. If this happens, stop the car as soon as it is safe to do so, turn off the engine and check the oil level. If the oil level is low, fill the engine oil to the proper level and start the engine again. If the light stays on with the engine running, turn the en- gine off immediately. In any instance where the oil light stays on when the engine is running, the engine should be checked by a Hyundai dealer before the car is driven again.
The brake fluid level warning light indi- cates that the brake fluid level in the brake master cylinder is low and hydraulic brake fluid conforming to DOT 3 or DOT 4 speci- fications should be added. After adding fluid, if no other trouble is found, the car should be immediately and carefully driven to a Hyundai dealer for inspection. If further trouble is experienced, the vehicle should not be driven at all but taken to a dealer by a professional towing service. Your Hyundai is equipped with dual-di- agonal braking systems. This means you still have braking on two wheels even if one of the dual systems should fail. With only one of the dual systems working, more than normal pedal travel and greater pedal pressure are required to stop the car. Also, the car will not stop in as short a distance with only half of the brake system working. If the brakes fail while you are driving, shift to a lower gear for additional engine braking and stop the car as soon as it is safe to do so.
FEATURES OF YOUR HYUNDAI
51
B260J02A-AAT
Charging System Warning Light
The charging system warning light should come on when the ignition is turned on, then go out when the engine is running. If the light stays on while the engine is run- ning, there is a malfunction in the electrical charging system. If the light comes on while you are driving, stop, turn off the engine and check under the hood. First, make certain the generator drive belt is in place. If it is, check the tension of the belt. Do this as shown on page 6-23 by pushing down on the center of the belt. Have the system checked by your Hyundai dealer as soon as possible.
B260B01JM-AAT
Tail Gate Open Warning Light
This light remains on unless the tail gate and/or tail gate window is completely closed and latched.
B260H02A-AAT
Parking Brake/Low Brake Fluid Level Warning Light
WARNING:
If you suspect brake trouble, have your brakes checked by a Hyundai dealer as soon as possible. Driving your car with a problem in either the brake electrical system or brake hydraulic system is dangerous, and could result in a serious injury or death.
Warning Light Operation The parking brake/brake fluid level warn- ing light should come on when the parking brake is applied and the ignition switch is turned to "ON" or "START". After the engine is started, the light should go out when the parking brake is released. If the parking brake is not applied, the warning light should come on when the ignition switch is turned to "ON" or "START", then go out when the engine starts. If the light comes on at any other time, you should slow the vehicle and bring it to a complete stop in a safe location off the roadway.
1FEATURES OF YOUR HYUNDAI
52
B260L02HP-GAT
Door ajar warning light and chime (If Installed)
The door ajar warning light warns you that a door is not completely closed and the chime warns you that the key is in the ignition switch. NOTE : The warning chime only sounds when- ever the key is in the ignition switch and the driver's side front door is open simul- taneously. The chime sounds until the key is removed from the ignition switch or the driver's side front door is closed.
B260N01A-AAT
Malfunction Indicator Light
This light illuminates when there is a mal- function of an exhaust gas related compo- nent, and the system is not functioning properly so that the exhaust gas regulation values are not satisfied. This light will also illuminate when the ignition key is turned to the "ON" position, and will go out in a few seconds. If it illuminates while driving, or does not illuminate when the ignition key is turned to the "ON" position, take your car to your nearest authorized Hyundai dealer and have the system checked.
B260P02Y-GAT
ABS Service Reminder Indicator (If installed)
When the key is turned to the "ON" position, the Anti-Lock Brake System indicator will come on and then go off in a few seconds. If the ABS SRI remains on, comes on while driving, or does not come on when the key is turned to the "ON" position, this indicates that there may be a problem with the ABS. If this occurs, have your vehicle checked by your Hyundai dealer as soon as pos- sible. The normal braking system will still be operational, but without the assistance of the anti-lock brake system.
B260M01A-AAT
Low Fuel Level Warning Light
The low fuel level warning light comes on when the fuel tank is approaching empty. When it comes on, you should add fuel as soon as possible. Driving with the fuel level warning light on or with the fuel level below "E" can cause the engine to misfire and damage the catalytic converter.
WARNING:
If both the ABS SRI and Parking Brake/ Brake fluid level warning lights remain "ON" or come on while driving, there may be a problem with E.B.D. (Electronic Brake Force Distribution). If this occurs, avoid sudden stops and have your vehicle checked by your Hyundai dealer as soon as possible.
B265C01O-AAT
B260Q01E-GAT
B260T01O-GAT
FEATURES OF YOUR HYUNDAI
53
Traction Control Indicator Lights (If installed)
Cruise Indicator Light (If installed)
The traction control indicators change op- eration according to the ignition switch position and whether the system is in operation or not. They will illuminate when the ignition key is turned to the "ON" position, but should go out after three seconds. If the TCS or TCS- OFF indicator stays on, take your car to your authorized Hyundai dealer and have the system checked. See section 2 for more information about the TCS.
B265C02LZ-AAT
Electronic Stability Control Indicator Lights (If installed)
The electronic stability control indicators change operation according to the ignition switch position and whether the system is in operation or not. They will illuminate when the ignition key is turned to the "ON" position, but should go out after three seconds. If the ESC or ESC- OFF indicator stays on, take your car to your authorized Hyundai dealer and have the system checked. See section 2 for more information about the ESC.
The cruise indicator light in the instrument cluster is illuminated when the cruise con- trol main switch on the end of the barrel is pushed. When the cruise control main switch is pushed a second time, the cruise control system will be and the light will turn off. Information on the use of cruise control may be found on page 1-88.
B260R01E-GAT
SET Indicator Light (If installed)
The SET indicator light in the instrument cluster is illuminated when the cruise con- trol switch is pushed downward to "SET (COAST)". The SET indicator light does not illuminate when the control switch is in the "CANCEL" position.
4WD System Warning Light (If installed)
When the key is turned to the "ON" position, the 4WD(Four Wheel Drive) system warn- ing light will come on and then go off in a few seconds.
CAUTION:
If the 4WD system warning light ( ) blinks while driving, this indicates that there is a malfunction in the 4WD sys- tem. If this occurs, have your vehicle checked by an authorized Hyundai dealer as soon as possible.
B260V01JM-GAT
4WD Lock Indicator Light (If installed)
The 4WD (Four Wheel Drive) lock indica- tor light in the instrument cluster is illumi- nated when the The 4WD lock switch is pushed. The purpose of this switch is to increase the drive power when driving on wet pavement, snow-covered roads and/ or off-road. The 4WD lock indicator light is turned off by pushing the switch again. NOTE: Do not use 4WD on normal dry pavement conditions.
1FEATURES OF YOUR HYUNDAI
54
B260W02JM-GAT
B265W02JM-GAT
Low tire pressure telltale (If installed)
The low tire pressure telltale comes on for 3 seconds after the ignition key is turned to the "ON" position. If the warning light does not come on, or continuously remains on after comming on for about 3 seconds when you turned the ignition key to the "ON" position, the Tire Pressure Monitoring System is not working properly. If this occurs, have your vehicle checked by an authorized Hyundai dealer as soon as possible. This warning light will also illuminate one or more of your tires is significantly under- inflated. You should stop and check your tires as soon as possible. If the warning light illuminates while driving, reduce ve- hicle speed immediately and stop the ve- hicle. Avoid hard braking and overcorrect- ing at the steering wheel. Inflate the tires to the proper pressure as indicated on the vehicle’s tire information placard.
WARNING:
Significantly low tire pressure makes the vehicle unstable and can contribute to loss of vehicle control and increased braking distances. Continued driving on low pressure tires will cause the tires to overheat and fail.
TPMS (Tire pressure monitor- ing system) malfunction indica- tor (If installed)
TPMS malfunction indicator comes on for 3 seconds after the ignition key is turned to the "ON" position. If the warning light does not come on, or continuously remains on after comming on for about 3 seconds when you turned the ignition key to the "ON" position, the Tire Pressure Monitor- ing System is not working porperly. If this occurs, have your vehicle checked by an authorized Hyundai dealer as soon as possible. The warning light also comes on and stays on when there is a problem with the Tire Pressure Monitoring System. If this happens, the system may not monitor the tire pressure. Have the system checked by an authorized Hyundai dealer as soon as possible.
WARNING:
o The TPMS cannot alert you to severe and sudden tire damage caused by external factors.
o If you feel any vehicle instability, im- mediately take your foot off the accel- erator and slowly move to a safe po- sition off the road.
B260Q01JM-GAT
Engine temperature warning light
The red indicator illuminates if the tem- perature of the engine coolant is above 248±5.5°F. Do not continue driving with an overheated engine. If your vehicle overheats, refer to "Overheating" in the index.
NOTE: If the engine temperature warning light illuminates, it indicates overheating that may damage the engine.
B270A01O-AAT
BRAKE PAD WEAR WARNING SOUND The front and rear disc brake pads have wear indicators that should make a high- pitched squealing or scraping noise when new pads are needed. The sound may come and go or be heard all the time when the vehicle is moving. It may also be heard when the brake pedal is pushed down firmly. Excessive rotor damage will result if the worn pads are not replaced. See your Hyundai dealer immediately.
INSTRUMENT CLUSTER
FEATURES OF YOUR HYUNDAI
55
B280A01A-AAT
FUEL GAUGE
B330A03A-AAT
TACHOMETER
B300A01A-AAT
SPEEDOMETER
OJM019017
The needle on the gauge indicates the
approximate fuel level in the fuel tank. The
fuel capacity is given in Section 9.
The tachometer registers the speed of your engine in revolutions per minute (rpm).
B330A01JM
B300A01JM Your Hyundai's speedometer is calibrated in miles per hour (on the outer scale) and kilometers per hour (on the inner scale).
CAUTION:
The engine should not be raced to such a speed that the needle enters the red zone on the tachometer face. This can cause severe engine damage and may void your warranty.
1FEATURES OF YOUR HYUNDAI
56
TRIP COMPUTER
B310B02JM-GAT
ODOMETER/TRIP ODOMETER
B400B02JM-GAT
(If installed)
Trip Computer Switch
(AT)
(MT)
(2)
(1)
(2)
(1)
(AT)
(MT)
(1)
(1)
B310B01JM-2
B310B02JM-C
Odometer (1) The odometer records the total driving distance in kilometers or miles, and is useful for keeping a record for mainte- nance intervals.
NOTE: Any alteration of the odometer may void your warranty coverage.
Trip odometer (2) o This mode indicates the drive distance travelled since the last drive time reset. o You can choose the TRIP A or TRIP B by pressing the trip odometer switch for less than 1 second.
The trip computer is a microcomputer- controlled driver information gauge that displays information related to driving, such as a tripmeter, distance to empty, average fuel consumption average speed, and drive time on the LCD.
Odometer (1) The odometer records the total driving distance in kilometers or miles, and is useful for keeping a record for mainte- nance intervals.
HJM2185
Pushing in the trip computer switch behind
the right side of the steering wheel changes
the display as follows;
TRIPMETER A
TRIPMETER B
DISTANCE TO EMPTY
AVERAGE FUEL CONSUMPTION
AVERAGE SPEED
DRIVE TIME
1. Tripmeter
2. Distance to Empty
Tripmeter
Distance to Empty
FEATURES OF YOUR HYUNDAI
57
HJM2186-C o This mode indicates the total distance travelled since the last tripmeter reset. Total distance is also reset to zero if the battery is disconnected.
o Pressing the trip computer switch for more than 1 second, when the tripmeter is being displayed, clears the tripmeter to zero.
o The meter's working range is from 0.0
to 999.9 miles.
o You can choose the TRIP A or TRIP B.
HJM2187-B o This mode indicates the estimated dis- tance to empty from the current fuel in the fuel tank and distance to empty symbol.
o When refueling with more than 1.6 gal- lons (6 liters), the trip computer will recognize refueling.
o For an accurate distance to empty, drive
more than 30 miles.
o When the distance to empty is less than 30 miles, the symbol will flash and the distance to empty digits will indicate "- --" until more fuel is added.
NOTE: o The distance to empty can differ from the actual tripmeter according to driv- ing conditions.
o The distance to empty can vary ac- cording to the driving conditions, driv- ing pattern or vehicle speed.
1FEATURES OF YOUR HYUNDAI
58
3. Average Fuel Consumption
4. Average Speed
5. Drive Time
Average Fuel Consumption
Average Speed
Drive Time
MPH
B400B02JM-C o This mode calculates the average fuel consumption from the total fuel used and the distance since the last average consumption reset.
o The total fuel used is calculated from the
fuel consumption input.
o For an accurate calculation, drive more
o The meter's working range is from 0.1 to
than 30 miles.
199.9 MPG.
HJM2187-A o This mode indicates the average speed
since the last tripmeter reset.
o Even if the vehicle is not in motion, the average speed keeps going while the engine is running.
o The meter’s working range is from 0 to
999 MPH.
o Press the trip computer switch for more than 1 seconds, when the average speed is being displayed, clears the average speed to "---".
HJM2187-C
o This mode indicates the drive time since
the last tripmeter reset.
o Even if the vehicle is not in motion, the drive time keeps going while the engine is running.
o The meter’s working range is from 0:00
to 99:59.
o Press the trip computer switch for more than 1 second, when the drive time is being displayed, clears the drive time to zero.
MULTI-FUNCTION SWITCH
LIGHT
B340A01A-AAT
COMBINATION TURN SIGNAL, HEADLIGHT AND HIGH-BEAM SWITCH Turn Signal Operation Pulling down on the lever causes the turn signals on the left side of the car to blink. Pushing upwards on the lever causes the turn signals on the right side of the car to blink. As the turn is completed, the lever will automatically return to the center posi- tion and turn off the turn signals at the same time. If either turn signal indicator light blinks more rapidly than usual, goes on but does not blink, or does not go on at all, there is a malfunction in the system. Check for a burned-out fuse or bulb or see your Hyundai dealer.
B340B01A-AAT
Lane Change Signal
B340C04A-AAT
Headlight Switch
FEATURES OF YOUR HYUNDAI
59
OJM019025
To indicate a lane change, move the lever
up or down to a point where it begins
flashing.
The lever will automatically return to the
center position when released.
OJM019026
To operate the headlights, turn the barrel
on the end of the multi-function switch. The
first position turns on the parking lights,
sidelights, tail lights and instrument panel
lights. The second position turns on the
headlights.
NOTE: The ignition must be in the "ON" position to turn on the headlights.
1FEATURES OF YOUR HYUNDAI
60
Parking Light Auto Cut o The purpose of this feature is to prevent
the battery from being discharged. The system automatically turns off the headlights and parking lights when the driver removes the ignition key and opens the driver- side door.
o With this feature, the parking light will be turned off automatically if the driver parks on the side of road at night. If necessary, to keep the lights on when the ignition key is removed, perform the following : 1) Open the driver-side door. 2) Turn the parking lights OFF and ON again using the light switch on the steering column.
B340D01A-AAT
High-beam Switch To turn on the headlight high beams, push the lever forward (away from you). The High Beam Indicator Light will come on at the same time. For low beams, pull the lever back toward you.
B340E01A-AAT
Headlight Flasher
B340G01L-GAT
Auto Light (If installed)
OJM019027
To flash the headlights, pull the switch
lever toward you, then release it. The head-
lights can be flashed even though the
headlight switch is in the "OFF" position.
OJM019028
To operate the automatic light feature, turn
the barrel on the end of the multi-function
switch. If you set the multi-function switch
to "AUTO", the tail lights and headlights
will be turned automatically on or off ac-
cording to external illumination.
WINDSHIELD WIPER AND WASHER SWITCH
B350A02JM-AAT
Windshield wiper/washer
A : Wiper speed control
· MIST – Single wipe · OFF – Off · INT – Intermittent wipe · LO – Low wiper speed · HI – High wiper speed
B : Intermittent wipe time adjustment
C : Wash with brief wipes
D : Rear wiper/washer control – Spraying washer fluid
· · OFF – Off · ON – Intermittent wipe after some nor-
mal wipe
– Wash with brief wipe
B350A07JM-U
Rear window wiper/washer (If installed)
·
B350A09JM-U
FEATURES OF YOUR HYUNDAI
61
B350A02A-AAT
Windshield wipers
Fast
Slow
B350A11JM-U Operates as follows when the ignition switch is turned ON.
MIST: For a single wiping cycle, push the lever upward and release it with the lever in the OFF position. The wip- ers will operate continuously if the lever is pushed upward and held.
OFF : Wiper is not in operation INT : Wiper operates intermittently at the same wiping intervals. Use this mode in a light rain or mist. To vary the speed setting, turn the speed control knob.
LO : Normal wiper speed HI
: Fast wiper speed
1FEATURES OF YOUR HYUNDAI
62
NOTE: To prevent damage to the wiper system, do not attempt to wipe away heavy accu- mulations of snow or ice. Accumulated snow and ice should be removed manu- ally. If there is only a light layer of snow or ice, operate the heater in the defrost mode to melt the snow or ice before using the wiper or activate the wind- shield wiper blade deicer.(If installed)
B350B01JM-GAT
Windshield Washer Operation
Mist Wiper Operation
B350B06JM-U
If a single wipe is desired in mist, push the windshield wiper and washer control lever upwards.
B350B05JM-U
To use the windshield washer, pull the wiper/washer lever toward the steering wheel. When the washer lever is operated, the wipers automatically three passes across the windshield. The washer continues to operate until the lever is released.
NOTE: o Do not operate the washer more than 15 seconds at a time or when the fluid reservoir is empty.
o In icy or freezing weather, be sure the wiper blades are not frozen to the glass prior to operating the wipers. o In areas where water freezes in win- ter, use windshield washer antifreeze.
B350C01O-GAT
Adjustable Intermittent Wiper Opera- tion
B390A02JM-AAT
Rear Window Wiper And Washer (If installed)
FEATURES OF YOUR HYUNDAI
63
NOTE: Do not operate the washer continuously for more than 15 seconds or when the fluid reservoir is empty; this could dam- age the system. Do not operate the wiper when the window is dry; this can result in scratching as well as premature wiper blade wear.
B350C03JM-U
B390A03JM-U
To use the intermittent wiper feature, place the wiper switch in the "INT" position. With the switch in this position, the interval be- tween wipes can be varied from approxi- mately 1 to 18 seconds by turning the interval adjuster barrel.
: The rear window wiper starts to op- erate three times after the washer fluid sprays onto the rear window.
OFF : Wiper is not in operation ON : Intermittent wiper operation after
some normal wiper operation.
: The washer fluid will be sprayed onto the rear window and the wiper operates while the rear window wiper barrel is placed in this posi- tion.
1FEATURES OF YOUR HYUNDAI
64
FRONT FOG LIGHT SWITCH
HAZARD WARNING SYSTEM
B360A04A-AAT
(If installed)
B370A01A-AAT
WINDOW DEFROSTER SWITCH
B385A01JM-AAT
Windshield wiper Blade De-icer (If installed)
OJM019020
To turn on the front fog lights, push the
switch. They will light when the headlight
switch is in the second position and the
ignition key is in the "ON" position.
NOTE: If you turn on the headlight high beams, the front fog lights will be turned off.
OJM019009
The hazard warning system should be
used whenever you find it necessary to
stop the car in a hazardous location. When
you must make such an emergency stop,
always pull off the road as far as possible.
The hazard warning lights are turned on by
pushing in the hazard switch. This causes
all turn signal lights to blink. The hazard
warning lights will operate even though
the key is not in the ignition.
To turn the hazard warning lights off, push
the switch a second time.
OJM019011
The windshield wiper blade de-icer is
turned on by pushing in the switch. To turn
the de-icer off, push the switch a second
time. The windshield wiper blade de-icer
automatically turns itself off after about 20
minutes.
B380A02Y-AAT
Rear Window Defroster Switch
NOTE: The engine must be running for the rear window defroster to operate.
FEATURES OF YOUR HYUNDAI
65
AUX OUTLET
B380A02Y-AAT
(if installed)
HJM2104
The rear window defroster and heated outside rearview mirrors are turned on by pushing in the switch. To turn the defroster off, push the switch a second time. The rear window defroster automatically turns itself off after about 15 minutes. To restart the defroster cycle, push in the switch again after it has turned itself off.
OJM019012
You can use an aux outlet to connect an audio device.
NOTE: When using a portable audio device con- nected to the power outlet, noise may occur during playback. If this happens, use the power source of the portable audio device.
CAUTION:
Do not clean the inner side of the rear window glass with an abrasive type of glass cleaner or use a scraper to remove foreign deposits from the inner surface of the glass as this may cause damage to the defroster ele- ments.
1FEATURES OF YOUR HYUNDAI
DIGITAL CLOCK
66
INSTRUMENT PANEL LIGHT CONTROL (RHEOSTAT)
CIGARETTE LIGHTER
B400A02A-AAT
B410A01A-AAT
B420A01A-AAT
HJM2137
There are three control buttons for the
digital clock. Their functions are:
HOUR - Push "H" to advance the hour indicated. MIN - Push "M" to advance the minute indicated. RESET -Push "R" to reset minutes to ":00" to facilitate resetting the clock to the correct time. When this is done:
Pressing "R" between 10 : 30 and 11 : 29
changes the readout to 11 : 00.
Pressing "R" between 11 : 30 and 12 : 29
changes the readout to 12 : 00.
Push the "R" button for 5 seconds to dis- play a 12- or 24-hour clock (If installed).
B410A01JM The instrument panel lights can be made brighter or dimmer by turning the instru- ment panel light control knob.
B420A01JM For the cigarette lighter to work, the key must be in the "ACC" position or the "ON" position. To use the cigarette lighter, push it all the way into its socket. When the element has heated, the lighter will pop out to the "ready" position. Do not hold the cigarette lighter pressed in. This can damage the heating element and create a fire hazard. If it is necessary to replace the cigarette lighter, use only a genuine Hyundai re- placement or its approved equivalent.
FEATURES OF YOUR HYUNDAI
ASHTRAY / COIN TRAY
B430A02JM-AAT
67
OJM019013
The front ashtray/coin tray may be opened
by pulling the ashtray lid. To remove the
ashtray to empty or clean it, lift the ashtray
upward and pull it out. The ashtray coin
tray light will only illuminate when the
external lights are on.
CAUTION:
o Use when the engine is running and remove a plug from the power outlet after using the electric appliance. Using when the engine stops or re- maining the electric appliance with plugged in for many hours may cause the battery to be discharged.
o Do not use the power outlet to connect electric accessories or equipment other than those designed to operate on 12 volts.
o Some electronic devices can cause electronic interference when plugged into the power outlet. These devices may cause excessive audio noise and malfunctions in other electronic systems or devices used in your ve- hicle.
POWER OUTLETS
B500D04JM-GAT
(If installed) Center
Rear
OJM019021
OJM019015
These supply 12V electric power to oper-
ate electric accessories or equipment only
when the key is in the "ON" or "ACC"
position.
1FEATURES OF YOUR HYUNDAI
DRINK HOLDER
68
B450A01JM-AAT
Front Drink Holder
B450B01JM-AAT
REAR DRINK HOLDER (If installed)
SUNROOF
B460A01Y-AAT
(If installed) Sun Shade
OJM019014
The front drink holder is located on the
main console .
WARNING:
o Use caution when using the drink hold- ers. A spilled beverage that is very hot can injure you or your passen- gers. Spilled liquids can damage inte- rior trim and electrical components. o Do not place objects other than cups or cans in the drink holder. The ob- jects can be thrown out in the event of a sudden stop or an accident, possi- bly injuring the passengers in the vehicle.
HJM2160
The rear drink holders is located in the rear
seat arm rest. The rear drink holder can be
used by pulling the rear seat armrest.
! WARNING:
Do not place objects other than cups or cans in the drink holder. This objects can be thrown out in the event of a sudden stop or an accident, possibly injuring the passengers in the vehicle.
HJM2029
Your HYUNDAI is equipped with a sliding
sunshade which you can manually adjust
to let in light with the sunroof closed, or to
block sunlight.
WARNING:
Never adjust the sunshade while driv- ing.
B460B02JM-GAT
Opening the Sunroof
HJM2025
If your vehicle is equipped with this feature,
you can slide or tilt your sunroof with the
sunroof control buttons located on the
overhead console.
The sunroof can only be opened, closed,
or tilted when the ignition switch is in the
"ON" position.
Sliding the sunroof Auto slide open To use the autoslide feature, momentarily (more than 1 second) press the SLIDE OPEN button on the overhead console. The sunroof will slide all the way open. To stop the sunroof sliding at any point, press any sunroof control button.
Manual slide open Press the SLIDE OPEN button on the over- head console for less than 0.5 second.
Auto slide close To close the sunroof, press the CLOSE button on the overhead console for more than 1 second. The sunroof will slide all the way close. To stop at the desired point, press any sunroof control button.
Auto Reverse If an object or part of the body is detected while the sunroof is closing automatically, it will reverse direction, and then stop. Auto reverse function does not work if a tiny obstacle is blocked between the sliding glass and the sunroof sash. You should always check that all passengers and objects are away from the sunroof before closing it.
WARNING:
Be careful that someone’s head, hands and body are not trapped by a closing sunroof.
FEATURES OF YOUR HYUNDAI
69
Manual slide close To close the sunroof, press the CLOSE button on the overhead console and hold it until the sunroof is closed.
! WARNING:
o Do not close a sunroof if anyone's hands, arms or body are between the sliding glass and the sunroof sash, as this could result in injury.
o Do not place your head or arms out of
the sunroof opening at any time.
o While the vehicle is moving, always keep the head, hands and other parts of the body of all occupants away from the roof opening. Otherwise, you could be seriously injured if the ve- hicle stops suddenly or if the vehicle is involved in an accident.
CAUTION:
o Do not open the sunroof in severely cold temperature or when it is cov- ered with ice or snow.
o Periodically remove any dirt that may have accumulated on the guide rails. o Do not press any sunroof control but-
ton longer than necessary. Damage to the motor or system com- ponents could occur.
1FEATURES OF YOUR HYUNDAI
70
B460C01JM-AAT
Tilting the Sunroof
Close To close the sunroof, press the CLOSE button on the overhead console and hold it until the sunroof is closed.
NOTE: After washing the car or after there is rain, be sure to wipe off any water that is on the sunroof before operating it.
HJM2024
Auto tilt open To use the autotilt feature, momentarily (more than 1 second) press the TILT UP button on the overhead console. The sunroof will tilt all the way open. To stop the sunroof tilting at any point, press any sunroof control button.
Manual tilt open Press the TILT UP button on the overhead console for less than 0.5 second.
B460E02JM-GAT
Resetting the sunroof Whenever the vehicle battery is disconnected or discharged, you have to reset your sunroof system as follows:
1. Turn the ignition key to the ON position. 2. According to the position of the sunroof,
do as follows. 1) In case that the sunroof has closed completely or been tilted : Press the TILT UP button for 1 second.
2) In case that the sunroof has slide- opened: Press and hold the CLOSE button for more than 5 seconds until the sunroof has closed completely. And then press the TILT UP button for 1 second
3. Then, release it. 4. Press and hold the TILT UP button once again until the sunroof has returned to the original position of TILT UP after it is raised a little higher than the maximum TILT UP position. When this is com- plete, the sunroof system is reset.
CAUTION:
If the sunroof is not reset, it may not operate properly.
INTERIOR LIGHT
B480B01JM-AAT
Map Light Without Sunroof
With sunroof
HJM2099
Push in the map light switch to turn the light
on or off. This light is convenient as a map
light at night or as a personal light for the
driver and the passenger.
FEATURES OF YOUR HYUNDAI
SPECTACLE CASE
71
B490A02JM-AAT
INTERIOR LIGHT
B491A03O-GAT
(If Installed)
HJM2100
The interior courtesy light has two buttons.
The two buttons are:
o DOOR
In the "DOOR" position, the interior cour-
tesy light comes on when any door is
opened regardless of the ignition key po-
sition.
The light goes out after 30 seconds if the
door is closed.
When a door is unlocked by the transmit-
ter, the interior light stays on for 30 seconds
as long as the door is not opened.
o ON
In the "ON" position, the light stays on at all
times. Do not leave this button pressed for
an extended period of time when the ve-
hicle is not running.
HJM2158
The spectacle case is located on the front
overhead console.
Push the end of the cover to open the
spectacle case.
WARNING:
Do not keep objects except spectacle inside the spectacle case. Such objects can be thrown out in the event of a sud- den stop or an accident, possibly injur- ing the passengers in the vehicle.
1FEATURES OF YOUR HYUNDAI
72
GLOVE BOX
B500A01S-AAT
CENTER CONSOLE COMPARTMENT
B505A02NF-GAT
Center Console Box
B500B01O-AAT
Illuminated Glove Box (If installed) Opening the glove box will automatically turn on the light when the multi-function switch is turned to the first/second position.
HJM2145
o To open the glove box, pull on the glove
box release lever.
o The glove box door can be locked (and
unlocked) with the key. (If installed)
WARNING:
To avoid the possibility of injury in case of an accident or a sudden stop, the glove box door should be kept closed when the car is in motion.
HJM2146
(1)
(2)
HJM2146-1
The center console box is used for storing
cassette tapes or small articles.
To use the center console box, pull up the
handle (1) or (2) lift the lid as shown.
! WARNING:
To avoid the possibility of injury in case of an accident or a sudden stop, the center console box lid should be kept closed when the car is in motion.
B505B01NF-GAT
Center Console Armrest (If Installed)
FEATURES OF YOUR HYUNDAI
73
! WARNING:
Do not place cups or cans in the drink holder when the console box lid is used as an armrest. It may result in spilling the beverage. A spilled beverage that is very hot can injure you or your passengers. Spilled liquids can damage interior trim and electric components.
HJM2147
The center console box can be used as
armrest. To use the console armrest, pull
out the console box lid by pulling up the
handle as shown.
NOTE: When not in use, always be sure it is locked in position properly.
1FEATURES OF YOUR HYUNDAI
74
OUTSIDE REARVIEW MIRROR
B510A01A-AAT
Manual Type
CAUTION:
If the mirror control is jammed with ice, do not attempt to break it free using the control handle or by manipulating the face of the mirror. Use an approved spray de-icer (not radiator antifreeze) to release the frozen mechanism or move the vehicle to a warm place and allow the ice to melt.
B510A01JM The outside rearview mirrors are equipped with a remote control for your convenience. It is operated by the control lever in the bottom front corner of the window. Before driving away, always check that your mirrors are positioned so you can see behind you, both to the left and right sides, as well as directly behind your vehicle. When using the mirror, always exercise caution when attempting to judge the dis- tance of vehicles behind or along side of you.
B510B01Y-AAT
Electric Type (If installed)
HJM2073
The outside rearview mirrors can be ad- justed to your preferred rear vision, both directly behind the vehicle, and to the rear of the left and right sides. The remote control outside rearview mir- ror switch controls the adjustments for both right and left outside mirrors.
To adjust the position of either mir- ror: 1. Move the selecting switch to the right or left to activate the adjustable mecha- nism for the corresponding door mirror. 2. Adjust mirror angle by depressing the appropriate perimeter switch as illus- trated.
FEATURES OF YOUR HYUNDAI
75
B510D01Y-AAT
OUTSIDE REARVIEW MIRROR HEATER (If installed)
B510C01A-AAT
FOLDING THE OUTSIDE REARVIEW MIRRORS
CAUTION:
o Do not operate the switch continu- ously for an unnecessary length of time.
o Scraping ice from the mirror face could cause permanent damage. To remove any ice, use a sponge, soft cloth or approved de-icer.
! WARNING:
Be careful when judging the size or dis- tance of any object seen in the passen- ger side rear view mirror. It is a convex mirror with a curved surface. Any ob- jects seen in this mirror are closer than they appear.
HJM2104
The outside rearview mirror heater is actu-
ated in connection with the rear window
defroster. To heat the outside rearview
mirror glass, push in the switch for the rear
window defroster. The rearview mirror glass
will be heated for defrosting or defogging
and will give you improved rear vision in
inclement weather conditions. Push the
switch again to turn the heater off. The
outside rearview mirror heater automati-
cally turns itself off after 15 minutes.
B510C01JM To fold the outside rearview mirrors, push them toward the rear. The outside rearview mirrors can be folded rearward for parking in narrow areas.
WARNING:
Do not adjust or fold the outside rearview mirrors while the vehicle is moving. This could result in loss of control, and an accident which could cause serious in- jury or death.
1FEATURES OF YOUR HYUNDAI
76
DAY/NIGHT INSIDE REARVIEW MIRROR
B520A01A-AAT
Manual Type
B520C04JM-AAT
AUTOMATIC DIMMING REAR VIEW MIRROR WITH COMPASS (If installed)
HJM2070
Your Hyundai is equipped with a day/night inside rearview mirror. The "night" position is selected by flipping the tab at the bottom of the mirror toward you. In the "night" position, the glare of headlights of cars behind you is reduced.
B520C08JM
1. Status Indicator LED 2. Feature Control Button 3. Rear Light Sensor 4. Display Window
Automatic dimming rear view mirror con- trols automatically the glare of headlights of the car behind you when it turned on by pressing and holding the button for more than 3 but less than 6 seconds. It is turned off by pressing and holding the button for same time once more.
1. To operate Compass feature Press and release the button, then the vehicle's directional heading will be dis- played. Pressing and releasing the button again will turn off the display. Heading display - E : East - W : West - S : South - N : North ex) NE : North East
2. Calibration procedure
Press and hold the button for more than 9
but less than 12 seconds. When the com-
pass memory is cleared a "C" will appear
in the display.
- Driving the vehicle in a circle at less than 5mph 2 times or until the compass heading appears.
- Driving in a circle in right-handed direc- tion and opposite direction are pos- sible, and if the calibration is completed, the compass heading will appear.
- Keep driving in a circle until a compass
heading appears.
3. Setting the compass zone 1. Find your current location and variance
zone number on the zone map.
4. Changing Mirror Angle setting
(If Installed):
Due to mirror positions being angled to- wards the driver, the compass mirror can also compensate for drivers seated on the Left Hand side of the vehicle (steering wheel on the LH side of the vehicle) or Right Hand side of the vehicle (steering wheel on the RH side of the vehicle).
B520C06JM
2. Press and hold the button for more than 6 but less than 9 seconds. The current zone number will appear in the display. 3. Press the button until the new zone number appears in the display. After you stop pressing the button in, the display will show a compass direction within a few seconds.
To adjust the Left Hand, “L” or Right Hand, “R”, setting: 1. Press and hold the button for more than
12 seconds.
2. Release then press the button to toggle
between “L” and “R”.
NOTE: This procedure also causes the com- pass to be de-calibrated.
3. To re-calibrate the compass, drive the vehicle in 2 complete circles at less than 8km/h (5mph).
FEATURES OF YOUR HYUNDAI
77
CAUTION:
1. Do not install the ski rack, antenna, etc. which are attached to the vehicle by means of a magnet. They affect the operation of the compass.
2. If the compass deviates from the cor- rect indication soon after repeated adjustment, have the compass checked at an authorized dealer.
3. The compass may not indicate the correct compass point in tunnels or while driving up or down a steep hill. (The compass returns to the correct compass point when the vehicle moves to an area where the geomag- netism is stabilized.)
4. When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing.
1FEATURES OF YOUR HYUNDAI
PARKING BRAKE
78
B530A02A-AAT
CAUTION:
Driving with the parking brake applied will cause excessive brake pad (or lin- ing) and brake rotor wear.
Releasing the parking brake To release the parking brake, first apply the foot brake and pull the parking brake lever slightly. Secondly, depress the re- lease button and lower the parking brake lever while holding the button.
HJM3026
Applying the parking brake To engage the parking brake, first apply the foot brake and then without pressing the release button in, pull the parking brake lever up as far as possible. In addition it is recommended that when parking the ve- hicle on a gradient, the shift lever should be positioned in the appropriate low gear on manual transaxle vehicles or in the P (Park) position on automatic transaxle ve- hicles.
TAIL GATE
B540A01JM-AAT
OJM019023
o Pull and raise the "DOOR" release lever
to open the tail gate.
o To close, lower the door, then press down on it until it locks. To be sure the door is securely fastened, try to pull it up again.
WARNING:
The tail gate should always be kept com- pletely closed while the vehicle is in motion. If it is left open or ajar, poisonous exhaust gases may enter the car result- ing in serious illness or death to the occupants. See additional warnings con- cerning exhaust gases on page 2-2.
B540B01JM-AAT
Tail gate Window
B540A01JM-AAT
SHOPPING BAG HOLDERS (If installed)
CAUTION:
o Do not hang a bag beyond 6 Ibs (3 kg). It may cause damage to the shopping bag holder.
o Return it to the original position after
using the shopping bag holder.
FEATURES OF YOUR HYUNDAI
79
(1)
(2)
OJM019024
o Pull the "GLASS" release lever (1) to open the tailgate window glass, and raise the window open lever (2).
o To close the tail gate window, lower the tail gate window, and it will close by itself. To be sure the tail gate window is se- curely fastened, try to pull it up again.
NOTE: The tail gate window lock is operated in connection with the tail gate lock. To open the tail gate window make sure the tailgate is unlocked with a key (if in- stalled) or the central door locking switch.
HJM2150
OJM019007
Shopping bag holders are located in the front console and on the backside of the rear seat. When not in use, return it to the original position.
1FEATURES OF YOUR HYUNDAI
80
HOW TO USE LUGGAGE ROOM
B640A01S-AAT
CARGO SECURITY SCREEN (If installed)
B650A01S-AAT
Stowage Precautions 1. Do not place objects on the cargo secu- rity screen. Such objects may be thrown about inside the vehicle and possibly injure vehicle occupants during an ac- cident or when braking.
2. For better fuel economy, do not carry
unnecessary weight.
3. Never allow anyone to ride in the lug- gage compartment. It is designed for luggage only.
4. Try to maintain the balance of the ve- hicle and locate the weight as far for- ward as possible.
B650A01JM
To use the security screen, pull it out of the retractor and hook it to the anchors as illustrated.
B545B02JM-GAT
Luggage Under Tray (If installed)
There is a multipurpose tray under the luggage mat.
HJM2166
Luggage Side Trim
B655A02JM-GAT
Covering screen (If Installed)
FEATURES OF YOUR HYUNDAI
81
HJM2168-1
Raise the luggage under tray cover with
the grip.
B545B01JM There are small article trays in the luggage side trim.
B655A02JM Covering shelf screen veils the luggage room to hang the screen hook to a head- rest pole. While not in use, place the screen hook to the hook holder.
CAUTION:
When folding the rear seatback forward, remove the hook from the headrest pole. Otherwise, the covering screen may be damaged or malformed.
1FEATURES OF YOUR HYUNDAI
82
B540D03HP-GAT
Luggage Net (If Installed)
CAUTION:
To prevent damage to the goods or the vehicle, care should be taken when car- rying fragile or bulky objects in the lug- gage compartment.
WARNING:
Avoid eye injury. DO NOT overstretch. ALWAYS keep face and body out of its path. DO NOT use when the luggage net straps have visible signs of wear or damage.
B540D01JM Some objects can be kept in the net in the luggage compartment. Use the luggage net on the floor or at the back of the luggage compartment to pre- vent objects from sliding.
ROOF RACK
B630A01JM-AAT
(If installed)
HJM2162
If your Hyundai has a roof rack, you can load things on top of your vehicle. Crossrails and fixing components to adapt the roof rack on your vehicle may be obtained from an authorized Hyundai dealer.
CAUTION:
o In case a sunroof is installed, do not position roof rack loads that could interfere with opening of the sunroof. o The following specifications are rec- ommended when loading cargo or luggage.
HIGH-MOUNTED REAR STOP LIGHT
REMOTE FUEL-FILLER LID RE- LEASE
B550A01A-AAT
B560A03JM-AAT
FEATURES OF YOUR HYUNDAI
83
CAUTION:
ROOF RACK
165 lbs (75 kg) Evenly Distributed
o Loading cargo or luggage above 165
lbs (75 kg) on the roof rack may dam-
age your vehicle.
When you carry large objects, never
let them hang over the rear or the
sides of your vehicle.
o To prevent damage or loss of cargo as you are driving, check frequently to make sure the luggage carrier and cargo are still securely fastened.
o Always drive your vehicle at a moder-
ate speed.
o To use the roof rails as a roof rack, you must fit the roof rails with two or more crossrails or equivalent before car- rying cargo or luggage on the roof.
o Loading cargo or luggage exceeding the specification on the roof rack may reduce the stability of your vehicle. o Do not allow cargo loads to rest di- rectly on the roof of your article; cross rails must be used.
B550A01JM
In addition to the lower-mounted rear stop- lights on either side of the car, the high mounted rear stoplight in the center of the rear window also lights when the brakes