are applied.
HJM2018
The fuel-filler lid may be opened from
inside the vehicle by pulling up on the fuel-
filler lid opener located on the front floor
area on the left side of the vehicle.
NOTE: If the fuel-filler lid will not open because ice has formed around it, tap lightly or push on the lid to break the ice and release the lid. Do not pry on the lid. If necessary, spray around the lid with an approved de-icer fluid (do not use radia- tor anti-freeze) or move the vehicle to a warm place and allow the ice to melt.
1FEATURES OF YOUR HYUNDAI
84
WARNING:
o Tighten the cap until it clicks, other-
wise the "
" light will illuminate.
o If you open the fuel filler cap during high ambient temperatures, a slight "pressure sound" may be heard. This is normal and not a cause for concern. Whenever you open the fuel filler cap, turn it slowly.
o Do not "top-off" after the nozzle auto-
matically shuts off when refueling.
o Automotive fuels are flammable/ex- plosive materials. When refueling, please note the following guidelines carefully. - Before touching the fuel nozzle or fuel filler cap, have one's hands in contact with metal parts away from the filler neck to discharge static electricity.
- Do not get back in the vehicle while refueling. Do not operate anything that can produce static electricity. Static electricity discharge can ig- nite fuel vapors resulting in explo- sion.
B560A01JM
! WARNING:
o Gasoline vapors are dangerous. Be- fore refueling, always stop the engine and never smoke or allow sparks and open flames near the filler area.
o Never operate your vehicle without a filler cap properly installed, flammable vapors and gasoline could leak out in dangerous situations such as a colli- sion or rollover. If the filler cap must be replaced, only use genuine Hyundai replacement parts.
o After refueling, make sure the fuel cap is installed securely to prevent fuel spillage in the event of an acci- dent.
- When using a portable fuel con- tainer be sure to place the con- tainer on the ground while refueling. Static electricity discharge from the container can ignite fuel vapors causing a fire. While starting refuel- ing contact should be maintained until the filling is complete.
- Do not use cellular phones around a gas station. The electric current or electronic interference from cel- lular phones can ignite fuel vapors causing a fire.
- When refueling always shut the en- gine off. Sparks by electrical equip- ment of the engine can ignite fuel vapors causing a fire. After refuel- ing, check to make sure the fuel filler cap is securely closed, and then start the engine.
- Do not smoke or try to light ciga- rettes around a gas station. Auto- motive fuels are flammable.
HOOD RELEASE
B570A03A-GAT
2. Push the secondary latch lever to the
left and lift the hood.
FEATURES OF YOUR HYUNDAI
85
Before closing the hood, return the support rod to its clip to prevent it from rattling. Lower the hood until it is about 1 ft. (30 cm) above the closed position and let it drop. Make sure that it locks into place.
CAUTION:
Make sure that the support rod has been released prior to closing the hood.
1. Pull the release knob to unlatch the
hood.
HJM2020
HJM2022
WARNING:
3. Hold the hood open with the support
rod.
o Always double check to be sure that the hood is firmly latched before driv- ing away. If it is not latched, the hood could open while the vehicle is being driven, causing a total loss of visibil- ity, which might result in an accident. o The support rod must be inserted completely into the hole provided in the hood whenever you inspect the engine compartment. This will pre- vent the hood from falling and possi- bly injuring you.
o Do not move the vehicle with the hood in the raised position, as vision is obstructed and the hood could fall or be damaged.
HJM2021
HJM2023
1FEATURES OF YOUR HYUNDAI
86
FLOOR MAT ANCHOR
SUN VISOR
B571A03Y-AAT
B580A01L-AAT
B570A01JM-A
When using a floor mat on the front floor carpet, make sure it attaches to the floor mat anchor in your vehicle. This keeps the floor mat from sliding forward.
WARNING:
o Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and interferes with the move- ment of the pedals during driving, it may cause an accident.
o Don't put an additional floor mat on the top of the anchored floor mat, other- wise the additional mat may slide for- ward and interfere with the move- ment of the pedals.
B580A02JM Your Hyundai is equipped with sun visors to give the driver and front passenger either frontal or sideward shade. To re- duce glare or to shut out direct rays of the sun, turn the sun visor down. A vanity mirror is provided on the back of the sun visor for the driver and front passenger.
NOTE: The Supplemental Restraint System (SRS) label containing useful information can be found on the back of each sun visor.
! WARNING:
Do not place the sun visor in such a manner that it obscures visibility of the roadway, traffic or other objects.
B580B01B-GAT
Illuminated Vanity Mirror (If installed) Opening the lid of the vanity mirror will automatically turn on the mirror light.
B585BA01JM-AAT
SUN VISOR EXTENDER
HJM2142-1
Your vehicle is equipped with sun visor
extenders that may be used when the visor
is in the side glass position.
STEERING WHEEL TILT LEVER
FEATURES OF YOUR HYUNDAI
FRONT DOOR EDGE WARNING LIGHT
87
B580C01LZ-AAT
TICKET HOLDER
B600A01A-AAT
B620A01S-AAT
B580C01JM The ticket holder is provided on the front of the sun visor for holding a tollgate ticket.
HJM2067
To Adjust the Steering Wheel: 1. Push the lever downward to unlock. 2. Raise or lower the steering wheel to the
desired position.
3. After adjustment, securely tighten the
lever by pulling it upward.
B620A01JM A red light comes on when the front door is opened. The purpose of this light is to assist when you get in or out and also to warn passing vehicles.
WARNING:
Do not attempt to adjust the steering wheel while driving as this may result in loss of control of the vehicle which may cause serious injury or death.
1FEATURES OF YOUR HYUNDAI
88
HORN
REAR SEAT ARM REST
CRUISE CONTROL
B610A01L-GAT
B611A01Y-AAT
B660A02S-AAT
(If installed) Type A
B610A01JM Press the pad on the steering wheel to sound the horn.
HJM2043
This arm rest is located in the center of the
rear seat back.
Type B
Main Switch
B660A01JM
Main Switch
B660A02JM
B660B04E-AAT
To Set the Cruise Speed Type A
The cruise control system provides auto- matic speed control for your comfort when driving on straight, open freeways, toll roads, or other noncongested highways. This system is designed to function above approximately 25 mph (40 km/h).
NOTE: Cruise control is not recommended for city driving, winding roads, slippery roads, heavy rain, or other bad weather conditions.
Type B
B660B01JM
B660B02JM
FEATURES OF YOUR HYUNDAI
89
1. Push in the cruise control main switch on the end of the barrel. The "CRUISE" indicator light in the instrument cluster will be illuminated. This turns the sys- tem on.
2. Accelerate to the desired cruising speed
above 25 mph (40 km/h). 3. Push the cruise control switch down- ward to "SET/COAST" or "−/SET" and release it. If the "SET/COAST" or "−/ SET" switch is selected, the cruise "SET" indicator light in the instrument cluster will illuminate.
4. Remove your foot from the accelerator pedal and the desired speed will auto- matically be maintained.
5. To momently increase speed, depress the accelerator pedal enough for the vehicle to exceed the preset speed. When you remove your foot from the accelerator pedal, the vehicle will re- turn to the speed you have set.
WARNING:
To avoid accidental cruise control en- gagement, keep the cruise control main switch off when not using the cruise control.
1FEATURES OF YOUR HYUNDAI
90
B660C04E-AAT
To Cancel the Cruise Speed Type A
Type B
B660C01JM
To disengage the cruise control system, pull the control switch toward the steering wheel to the "CANCEL" position. Additionally, the following actions will dis- engage the system:
B660D03E-AAT
To Resume the Preset Speed Type A
o Depress the brake pedal. o Depress the clutch pedal (Manual
transaxle).
o Shift the selector lever to "P" or "N"
position (Automatic transaxle).
o Decrease the vehicle speed to less
than 25 mph (40 km/h).
o Release the main switch.
Type B
B660D01JM
B660C02JM
B660D02JM
The vehicle will automatically resume the
speed set prior to cancellation when you
push the control switch upward to the "RES/
ACC" or "+/RES" position and release it,
providing the vehicle speed is above 25
mph (40 km/h).
If the control switch "RES/ACC" or "+/RES"
is selected, the cruise "SET" indicator in
the instrument cluster will illuminate.
B660F05E-AAT
To Reset at a Slower Speed Type A
FEATURES OF YOUR HYUNDAI
91
1. Push the control switch downward to "SET /COAST" or "−/SET"and hold it. The vehicle will decelerate. If the "SET/COAST" or "−/SET" switch is selected, the cruise "SET" indicator light in the instrument cluster will illuminate. 2. When the desired speed is obtained, release the control switch. While the control switch is pushed, the vehicle speed will gradually decrease.
B660E02E-AAT
To Reset at a Faster Speed 1. Push the control switch upward to the "RES/ACC" or "+/RES" position and hold it. If the control switch "RES/ACC" or "+/ RES" is selected, the cruise "SET" indi- cator in the instrument cluster will illumi- nate.
2. Accelerate to desired speed and re- lease the control switch. While the con- trol switch is held, the vehicle will gradu- ally gain speed.
Type B
B660B01JM
B660B02JM
! WARNING:
o Keep the cruise control main switch off when not using the cruise control to avoid inadvertently setting a speed. o Use the cruise control system only when traveling on open highways in good weather.
o Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.
o Pay particular attention to the driving conditions whenever using the cruise control system.
1FEATURES OF YOUR HYUNDAI
92
! WARNING:
o During cruise-control driving with a manual transaxle vehicle, do not shift into neutral without depressing the clutch pedal, or the engine will be overrevved. If this happens, depress the clutch pedal or release the main switch.
o With the cruise control engaged, when the brake pedal is applied, it is normal to hear the cruise control system de- activate. This is an indication of nor- mal system operation. o During normal cruise control opera- tion, when the "SET/COAST" or "−−−−−/ SET" is activated or reactivated after applying the brakes, the cruise con- trol will energize after approximately 3 seconds. This delay is normal.
HEATING AND COOLING CONTROL
B710A01JM-GAT
1. Side Defroster Nozzle 2. Side Ventilators 3. Windshield Defroster Nozzles 4. Center Ventilators
B710A02JM
FEATURES OF YOUR HYUNDAI
9393939393
B710B02O-AAT
CENTER VENTILATOR The center ventilators are located in the middle of the dashboard. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are opened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ". Keep these vents clear of any obstructions.
B710C02HP-AAT
SIDE VENTILATOR The side ventilators are located on each side of the dash board. To change the direction of the air flow, move the knob in the center of the vent up-and-down and side-to-side. The vents are closed when the vent knob is moved to " " position. The vents are opened when the vent knob is moved to " ". Keep these vents clear of any obstructions.
1FEATURES OF YOUR HYUNDAI
94
HEATING AND VENTILATION
B670A01JM-AAT
B670B01A-AAT
Fan Speed Control (Blower Control)
B670C03E-AAT
Air Intake Control
HJM2109A
There are three controls and two switches for the heating and cooling system. They are:
1. Air flow control 2. Fan speed control 3. Temperature control 4. Air intake control switch 5. Air conditioning switch
HJM2116A
This is used to turn the blower fan on and off and to select the fan speed. The blower fan speed, and therefore the volume of air delivered from the system, may be controlled manually by setting the blower control between the "1" and "4" position.
HJM2118A This is used to select fresh outside air or recirculating inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.
FRESH MODE ( ) : The indicator light on the button goes off when the air intake control is fresh mode.
RECIRCULATION MODE ( ): The indicator light on the button is illuminated when the air intake control is recirculation mode.
With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function se- lected. With the "Recirculation" mode selected, air from within the passenger compart- ment will be drawn through the heating system and heated or cooled according to the function selected.
NOTE: It should be noted that prolonged opera- tion of the heating in "Recirculation" ) may result in fogging of the mode ( windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Recircu- ) selected may result lation" mode ( in the air within the passenger compart- ment becoming excessively dry.
B670D01JM-GAT
Air Flow Control
FEATURES OF YOUR HYUNDAI
9595959595
HJM2111
Face-Level
Selecting the "Face" mode will cause air to be discharged through the side and center ventilators.
HJM2110A This is used to turn the blower fan on/off and to direct the flow of air. Air can be directed to the floor, dashboard outlets, or windshield. Five symbols are used to rep- resent Face, Bi-Level, Floor, Floor-Defrost and Defrost air position. The MAX A/C mode is used to cool the inside of the vehicle faster. The "OFF" mode is used to turn the blower fan off.
1FEATURES OF YOUR HYUNDAI
96
HJM2114
HJM2113
HJM2112
Bi-Level
Air is discharged through the face vents and the floor vents.
Floor-Level
Air is discharged through the floor vents, windshield defroster nozzle, side defroster nozzle and side ventilator.
Floor-Defrost Level
Air is discharged through the windshield defroster nozzle, the floor vents, side de- froster nozzle and side ventilator. If the "Floor-Defrost" mode is selected, the A/C will be turned on automatically and "Fresh" mode will be activated.
FEATURES OF YOUR HYUNDAI
9797979797
NOTE: o The air intake control switch will change to " " mode when the igni- tion switch is turned "ON" with the MAX A/C mode selected.
o When you change to another mode from MAX A/C, the A/C and the air intake control switch are set to the following chart.
Air Intake
Control Switch
or
A/C
ON
ON or OFF *
OFF
OFF
ON or OFF *
ON
ON
* The A/C or the air intake control switch
returns to its former setting.
HJM2115
B670C02JM
Defrost-Level
Air is discharged through the windshield defroster nozzle, side defroster nozzle and side ventilator. If the "Defrost" mode is selected, the A/C will be turned turn on automatically and "Fresh" mode will be activated to improve windshield defrosting.
MAX A/C
MAX A/C-Level
Air is discharged through the face level vents. If the "MAX A/C" mode is selected, the A/C will turn on automatically and "Recircula- tion" mode will be activated.
1FEATURES OF YOUR HYUNDAI
98
B670E02A-AAT
Temperature Control
B690A01E-AAT
HEATING CONTROLS
B670C03JM
OFF Off-Level Air is discharged through the windshield defroster nozzle, side defroster nozzle and side ventilator.
NOTE: If the air flow control is off, the air intake control is set to the fresh mode auto- matically.
Cool
Warm
HJM2117
This control is used to adjust the degree of heating or cooling desired.
B690A01JM-A For normal heating operation, set the air ) position intake control to the fresh air ( and the air flow control to the floor ( position.
For faster heating, the air intake control should be set in the recirculate ( ) posi- tion.
If the windows fog up, set the air flow ) position. (The control to the defrost ( A/C will be on automatically and "Fresh" mode will be activated.)
For maximum heat, rotate the temperature control to "Warm".
BI-LEVEL HEATING
VENTILATION
B700A02E-AAT
B710A01S-AAT
B700A01JM-A
B710A01JM-A
Your Hyundai is equipped with bi-level heating controls. To use this feature:
To operate the ventilation system:
o Set the air intake control to the fresh air
).
o Set the air flow control at the bi-level
o Adjust the fan speed control to the de-
) position.
) position.
sired speed.
"Cool" and "Warm".
o Set the air intake control to "Fresh" mode
o To direct all intake air to the dashboard vents, set the airflow control to "Face"
o Adjust the fan speed control to the de-
).
sired speed.
"Cool" and "Warm".
o Set the temperature control between
o Set the temperature control between
FEATURES OF YOUR HYUNDAI
9999999999
B730A01L-AAT
).
Operation Tips o To keep dust or unpleasant fumes from entering the car through the ventilation system, temporarily set the air intake control to ( Be sure to return the control to ( when the irritation has passed to keep fresh air in the vehicle. This will help keep the driver alert and comfortable. o Air for the heating/cooling system is drawn in through the grilles just ahead of the windshield. Care should be taken that these are not blocked by leaves, snow, ice or other obstructions.
o To prevent interior fog on the wind- shield, set the air intake control to the ) position, fan speed to the fresh air ( desired position, turn on the air condi- tioning system, and adjust temperature control to desired temperature.
1FEATURES OF YOUR HYUNDAI
100
AIR CONDITIONING SYSTEM
B740A01S-AAT
Air Conditioning Switch (If installed)
B740B01S-AAT
Air Conditioning Operation for Cooling
o Set the temperature control to "Cool". ("Cool" provides maximum cooling. The temperature may be moderated by moving the control toward "Warm".)
o Adjust the fan control to the desired speed. For greater cooling, turn the fan control to one of the higher speeds or temporarily select the "Recirculation )" position on the air intake control.
HJM2119
The air conditioning is turned on or off by
pushing the A/C button on the heating/air
conditioning control panel.
To use the air conditioning to cool the interior:
B740B01JM-A
o Set the side vent control to "OFF", to shut
off outside air entry.
o Turn on the fan control switch. o Turn on the air conditioning switch by pushing the switch. The air condition- ing indicator light should come on at the same time.
o Set the air intake control to "Fresh" mode
).
B720A01JM-AAT
DEFROSTING/DEFOGGING
A Type
B Type
A Type
B Type
FEATURES OF YOUR HYUNDAI
101101101101101
B720B01JM
B720B02JM
Use the heating/ventilation system to defrost or defog the windshield: To remove interior fog on the windshield: o Set the air flow control to the defrost ( ) position. (The A/C will be turned on automatically and "Fresh" mode will be activated.)
To remove frost or exterior fog on the windshield: o Set the air flow control to the defrost ( ) position. (The A/C will be turned on automatically and "Fresh" mode will be activated.)
o Set the temperature control to the desired position. o Set the fan speed control between "1" and "4" position.
o Set the temperature control to the warm. o Set the fan speed control to position "3" or "4". o Activate windshield wiper blade de-icer (If installed)
NOTE: When the A/C is operated continuously on the floor-defrost level ( ) or defrost level ( ), it may cause fog to form on the exterior windshield because of the temperature difference. At this time set the air flow control to the face level position ( ) and fan speed control to the low position.
1FEATURES OF YOUR HYUNDAI
102
B740C01S-AAT
Dehumidified Heating For dehumidified heating:
o Turn on the fan control switch. o Turn on the air conditioning switch. The air conditioning indicator light should come on at the same time.
o Set the air intake control to the "Fresh"
mode (
).
o Set the air flow control to the "Face" ( ). o Adjust the fan control to the desired
speed.
o For more rapid action, set the fan at one
of the higher speeds.
o Adjust the temperature control to pro-
vide the desired amount of warmth.
B740D01A-AAT
Operation Tips o If the interior of the car is hot when you first get in, open the windows for a few minutes to expel the hot air.
o When you are using the air conditioning system, keep all windows closed to keep hot air out.
o When moving slowly, as in heavy traffic, shift to a lower gear. This increases engine speed, which in turn increases the speed of the air conditioning com- pressor.
o On steep grades, turn the air condition- ing off to avoid the possibility of the engine over-heating.
o During winter months or in periods when the air conditioning is not used regu- larly, run the air conditioning once ev- ery month for a few minutes. This will help circulate the lubricants and keep your system in peak operating condi- tion.
AUTOMATIC HEATING AND COOLING CONTROL SYSTEM
B970A01Y-AAT
(If installed) Your Hyundai is equipped with an auto- matic heating and cooling control system controlled by simply setting the desired temperature.
B970B02JM-GAT
Heating and Cooling Controls
FEATURES OF YOUR HYUNDAI
103103103103103
1. Temperature Control Switch 2. Air Flow Control Switch 3. Display Window 4. Defroster Switch 5. Blower Fan Control Switch
6. AUTO (Automatic Control)Switch 7. OFF Switch 8. Air Conditioning Switch 9. Air lntake Control Switch
B970B01JM
1FEATURES OF YOUR HYUNDAI
104
B970C01JM-AAT
Automatic Operation
HJM2124-1
The FATC (Full Automatic Temperature Control) system automatically controls heating and cooling by doing as follows:
1. Push the "AUTO" button. The indicator light will illuminate confirming that the Face, Floor and/or Bi-Level modes as well as the blower speed and air condi- tioner will be controlled automatically.
HJM2126-1
2. Push the "TEMP" button to set the de-
sired temperature. The temperature will increase to the maximum 90°F(32°C) by pushing the " button. Each push of the button will cause the temperature to increase by 1°F(0.5°C). The temperature will decrease to the minimum 62°F(17°C) by pushing the " " button. Each push of the button will cause the temperature to decrease by 1°F(0.5°C).
NOTE:
o If the battery has been discharged or
disconnected, the temperature mode
will reset to Centigrade degrees.
This is a normal condition and you can
change the temperature mode from
Centigrade to Farenheit as follows;
Press the "TEMP" down button and
"AUTO" button simultaneously for 3
secs. The display shows that the unit
of temperature is adjusted to Centi-
grade or Fahrenheit.
(°C→→→→→°F or °F→→→→→°C)
o Never place anything covering the sensor which is located on the instru- ment panel to ensure better control of the heating and cooling system.
Photo sensor
HJM2086
B980B01Y-AAT
Fan Speed Control Switch
B670C03Y-AAT
Air Intake Control Switch
FEATURES OF YOUR HYUNDAI
105105105105105
B980A01Y-AAT
MANUAL OPERATION The heating and cooling system can be controlled manually as well by pushing buttons other than the "AUTO" button. In this state, the system sequentially works according to the order of buttons selected. The function of the buttons which are not selected will be controlled automatically. Press the "AUTO" button in order to convert to automatic control of the system.
HJM2123-1
The fan speed can be set to the desired
speed by pressing the appropriate fan
speed control button. The higher the fan
speed is, the more air is delivered. Press-
ing the "OFF" button turns off the fan.
B670C01JM
This is used to select fresh outside air or recirculation inside air. To change the air intake control mode, (Fresh mode, Recirculation mode) push the control button.
FRESH MODE ( ) : The indicator light on the button goes on when the air intake control is fresh mode.
RECIRCULATION MODE ( ) : The indicator light on the button is illuminated when the air intake control is recirculation mode.
1FEATURES OF YOUR HYUNDAI
106
With the "Fresh" mode selected, air enters the vehicle from the outside and is heated or cooled according to the function se- lected.
With the "Recirculation" mode selected, and air from within the passenger com- partment will be drawn through the heat- ing system and heated or cooled accord- ing to the function selected.
NOTE: It should be noted that prolonged opera- tion of the heating system in "recircula- tion" mode will give rise to fogging of the windshield and side windows and the air within the passenger compartment will become stale. In addition, prolonged use of the air conditioning with the "Recircu- lation" mode selected may result in the air within the passenger compartment becoming excessively dry.
B980D01Y-AAT
Heating and Cooling System Off Press the "OFF" button to stop the opera- tion of the heating and cooling system.
B980E01E-GAT
Air Flow Control
HJM2128-1
This is used to direct the flow of air. Air can
be directed to the floor, dashboard outlets,
or windshield. Four symbols are used to
represent Face, Bi-Level, Floor and Floor-
Defrost air position.
HJM2111
Face-Level
When selecting the "Face" mode, the indi- cator light will come on, causing air to be discharged through the face level vents.
FEATURES OF YOUR HYUNDAI
107107107107107
HJM2114
HJM2113
HJM2112
Bi-Level
When selecting the "Bi-Level" mode, the indicator light will come on and the air will be discharged through the face vents and the floor vents.
Floor-Level
When selecting the "Floor-Level" mode, the indicator light will come on and the air will be discharged through the floor vents, windshield defroster nozzle, side defroster nozzle and side ventilator.
Floor-Defrost Level
When selecting the "Floor-Defrost" mode, the indicator light will come on and the air will be discharged through the windshield defrost vents, the floor vents and side de- froster nozzle and side ventilator .
1FEATURES OF YOUR HYUNDAI
108
B980F01JM-GAT
Defrost Switch
HJM2138-1
When the "Defrost" button is pressed, the
) mode will be automatically selected
and the air will be discharged through the
windshield defrost nozzle, side defroster
nozzle and side ventilator. To assist in
defrosting, the air conditioning will oper-
ate if ambient temperature is higher than
2°C, and automatically turns off if the am-
bient temperature drops below 2°C.
CLIMATE CONTROL AIR FILTER (IN FRONT OF BLOWER UNIT)
B760A05E-AAT
(If installed)
Outside air
Inside air Filter
Inside air
Blower fan
Evaporator core
Heater core
B760A01E The climate control air filter is located in front of the blower unit behind the glove box. It operates to decrease the amount of pol- lutants entering the car. To replace the climate control air filter, refer to the page 6-17.
CAUTION:
o Replace the filter every 10,000 miles (15,000 km) or once a year. If the car is being driven in severe conditions such as dusty, rough roads, more frequent climate control air filter in- spections and changes are required. o When the air flow rate is suddenly decreased, the system should be checked by an authorized dealer.
STEREO SOUND SYSTEM
B750A02A-AAT
How Car Audio Works FM reception
Ionosphere
AM reception
Ionosphere
FM radio station
Mountains
FEATURES OF YOUR HYUNDAI
109109109109109
Unobstructed
area
Buildings
B750A02L AM broadcasts can be received at greater distances than FM broadcasts. This is because AM radio waves are transmitted at low frequencies. These long, low fre- quency radio waves can follow the curva- ture of the earth rather than travelling straight out into the atmosphere. In addi- tion, they curve around obstructions so that they can provide better signal cover- age.
B750A01L AM and FM radio signals are broadcast from transmitter towers located around your city. They are intercepted by the radio antenna on your car. This signal is then received by the radio and sent to your car speakers. When a strong radio signal has reached your vehicle, the precise engineering of your audio system ensures the best pos- sible quality reproduction. However, in some cases the signal coming to your vehicle may not be strong and clear. This can be due to factors such as the distance from the radio station, closeness of other strong radio stations or the presence of buildings, bridges or other large obstruc- tions in the area.
Iron bridges
Obstructed area
B750A03L FM broadcasts are transmitted at high fre- quencies and do not bend to follow the earth's surface. Because of this, FM broad- casts generally begin to fade at short dis- tances from the station. Also, FM signals are easily affected by buildings, moun- tains, or other obstructions. These can result in certain listening conditions which might lead you to believe a problem exists with your radio. The following conditions are normal and do not indicate radio trouble:
1FEATURES OF YOUR HYUNDAI
110
B750A04L o Fading - As your car moves away from the radio station, the signal will weaken and sound will begin to fade. When this occurs, we suggest that you select an- other stronger station.
o Flutter/Static - Weak FM signals or large obstructions between the transmitter and your radio can disturb the signal causing static or fluttering noises to occur. Reducing the treble level may lessen this effect until the disturbance clears.
B750A05L o Station Swapping - As an FM signal weakens, another more powerful sig- nal near the same frequency may begin to play. This is because your radio is designed to lock onto the clearest sig- nal. If this occurs, select another station with a stronger signal.
o Multi-Path Cancellation - Radio signals being received from several directions can cause distortion or fluttering. This can be caused by a direct and reflected signal from the same station, or by sig- nals from two stations with close fre- quencies. If this occurs, select another station until the condition has passed.
B750B05Y-AAT
Using a cellular phone or a two-way radio When a cellular phone is used inside the vehicle, noise may be produced from the audio equipment. This does not mean that something is wrong with the audio equip- ment. In such a case, use the cellular phone at a place as far as possible from the audio equipment.
WARNING:
Hyundai recommends that you never use a cell phone while driving. This could result in loss of control, and an accident that may cause death, serious injury, or property damage. You must stop at a safe place to use a cellular phone.
NOTE: Some states and cities have regulations prohibiting the use of cell phones while driving. You should be aware of the spe- cific requirements in your area.
CARE OF DISCS
B850A02F-AAT
Proper Handling
Storage When not in use, place your discs in their individual case and store them in a cool place away from the sun, heat, and dust. Do not grip or pull out the disc with your hand while the disc is being pulled into the unit by the self loading mechanism.
FEATURES OF YOUR HYUNDAI
111111111111111
ANTENNA
B870D02JM-AAT
Roof Antenna
Keep Your Discs Clean
Type A
Type B
B850A01L Handle your disc as shown. Do not drop the disc. Hold the disc so you will not leave fingerprints on the surface. If the surface is scratched, it may cause the pickup to skip signal tracks. Do not affix tape, paper, or gummed labels on the disc. Do not write on the disc.
Damaged Disc Do not attempt to play damaged, warped or cracked discs. These could severely damage the playback mechanism.
B850A02L
Fingerprints, dust, or soil on the surface of a disc could cause the pickup to skip signal tracks. Wipe the surface clean with a clean soft cloth. If the surface is heavily soiled, dampen a clean soft cloth in a solution of mild neutral detergent to wipe it clean. See drawing.
B870D02JM-U Your car uses a roof antenna to receive both AM and FM broadcast signals. This antenna is a removable type. To re- move the antenna, turn the antenna coun- terclockwise. To install the antenna, turn the antenna clockwise.
1FEATURES OF YOUR HYUNDAI
112
CAUTION:
o Be sure to remove the antenna before washing the car in an automatic car wash or it may be damaged.
o Before entering a place with a low height clearance, be sure to adjust the roof antenna low.
o In some vehicles, the antenna can be
folded into only front position.
o When reinstalling your antenna, it is important that it is fully tightened to ensure proper reception.
AUDIO SYSTEM
PA710E01JM-GAT
RADIO, SET UP, VOLUME CONTROL (PA 710S) (If installed)
FEATURES OF YOUR HYUNDAI
113113113113113
1. FM Selection Button 2. AM Selection Button 3. XM Selection Button 4. CD/AUX Selection Button 5. Automatic Channel Selection Button 6. Power ON/OFF 7. MUTE Button 8. SCAN Button 9. Information Display Button 10. SET UP Button 11. TUNE/ENTER Button 12. CAT(FLDR) Button 13. Preset Button
10
12
11
13
A-200JMU
1FEATURES OF YOUR HYUNDAI
114
1. FM Selection Button Turns to FM mode and toggles FM1 and FM2 when the button is pressed each time.
2. AM Selection Button Turns to AM mode, and toggles in the order of AM1➟AM2➟···➟AM1···when the button is pressed each time.
3. XM Selection Button Turns to XM mode, and toggles in the order of XM1➟XM2➟XM3➟···➟XM1··· when the button is pressed each time.
4. CD/AUX Selection Button If there is a cd in the CDP DECK it turns to CD mode, and if a device is connected to AUX then it toggles. CD➟AUX➟CD··· when the button is pressed each time.(It will not turn to AUX if the auxiliary device is not connected)
5. Automatic Channel Selection
Button
o When the [SEEK
]button is pressed, it reduces the band frequency by 200khz to automatically select channel. Stops at the previous frequency if no channel is found.
o When the [SEEK
]button is pressed, it increases the band frequency by 50khz to automatically select channel. Stops at the previous frequency if no channel is found.
6. Power ON/OFF & Volume Control
Button
Turns on/off the set when the IGNITION SWITCH is on ACC or ON. If the button is turned to the right, it increases the volume and left, decreases the volume.
7. MUTE Button Press to temporarily cut off the Sound.
8. SCAN Button If this button is pressed, the frequencies will become increased and receive the corresponding broadcasts. This function will play the frequencies for 5 seconds (XM MODE : 10 seconds) each and find other broadcasts as the frequency increases.
Press the button again when desiring to continue listening to the currently playing broadcast.
9. Information Display Button Information Display function operation (In- formation is displayed each time (the) Key is pressed) : Pressing the Category ➟Channel Name ➟Artist Name➟Song Title➟Category-KEY for 3 seconds will display the corresponding text then be- come restored. Text Scroll operation : After pressing (the) Key, if the text to be displayed is longer than the LCD text line, then rotating the Tune Knob will operate the Page up function displaying 8 charac- ters for 3 seconds each - displays the maximum lines of text supported by XM.
10. SET UP Button Press this button to turn to the XMoption, SCROLL and adjustment mode. If no action is taken for 5 seconds after pressing the button, it will return to the play mode.(After entering SET UP mode, move between items using the left, right and PUSH functions of the TUNE button.) The set up item changes from AUDIO ad- justment, TEXT SCROLL, XM setup.
11. TUNE/ENTER Button Turn this button clockwise by one notch to increase frequency by 0.05Mhz from cur- rent frequency. Turn this button counterclockwise by one notch to decrease frequency by 0.05Mhz from current frequency. Press this button while holding SET UP button to activate / inactivate the item to. Select SET UP item using left and right function of the Tune button.
Pressing the changes the BASS, MIDR- ANGE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Audio control knob clockwise or counter- clockwise.
o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.
o MID-RANGE Control To increase the MID-RANGE, rotate the knob clockwise, while to decrease the MID-RANGE, rotate the knob counterclock- wise.
o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.
o FADER Control Turn the control knob clockwise to emph- asize rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).
o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).
] Button when Category Up
12. CAT(FLDR) Button
Moves [CAT
search operation.
o Category is moved Up from the cat-
egory currently being received and
Category Name becomes displayed.
o If the Enter Key is not pressed within 5
seconds, then the previous mode will
be restored.
FEATURES OF YOUR HYUNDAI
115115115115115
o If the Key is pressed while in the last Category, then the first category will become displayed and operation will be repeated.
o Corresponding category can be se-
lected by pressing ENTER.
] Button when Category
Moves [CAT
Down search operation.
o Category is moved Down from the cat-
egory currently being received and
Category Name becomes displayed.
o If the Enter Key is not pressed within 5
seconds, then the previous mode will
be restored.
o If the [CAT
] Key is pressed while in the first Category, then the last category will become displayed and operation will be repeated.
o Corresponding category can be se-
lected by pressing ENTER.
13. Preset Button Push [1]~[6] buttons less than 0.8 seconds to play the channel saved in each button. Push pre-set button for 0.8 seconds or longer to save current channel to the re- spective button with a beep.
1FEATURES OF YOUR HYUNDAI
116
PA710F01JM-GAT
CD (PA 710S) (If installed)
10
11
1. CD Loading Slot 2. CD Indicator 3. CD Eject Button 4. CD/AUX Selection Button 5. Automatic Track Selection Button 6. INFO Button 7. TUNE/ENTER Button 8. RANDOM Play Button 9. REPEAT Button 10. SCAN Play Button 11. FOLDER Button
A-201JMU
1. CD Loading Slot Please face printed side upward and gen- tly push in. When the ignition switch is on ACC or ON and power is off, power is automatically turned on if the CD is loaded. This CDP supports both 8cm and 12 cm CDs. But if VCD, Data CD, MP3 CD are loaded, "Er-6" message will appear and CD will be ejected.
2. CD Indicator When car ignition switch is ACC or ON and if the CD is loaded, this indicator is lighted. If the CD is ejected the light is turned off.
3. CD Eject Button Push button to eject the CD during CD playback. This button is enabled when ignition switch is off.
4. CD/AUX Selection Button If there is a cd in the CDP DECK it turns to CD mode, and if a device is connected to AUX then it toggles. CD➟AUX➟CD··· when the button is pressed each time.(It will not turn to AUX if the auxiliary device is not connected)
5. Automatic Track Selection Button
o Push [SEEK
] button for less than 0.8
seconds to play from the beginning of
current song.
o Push [SEEK
] button for less than 0.8
seconds and press again within 1 sec-
onds to play the previous song.
o Push [SEEK
] button for 0.8 or longer to initiate reverse direction high speed sound search of current song.
o Push [SEEK
] button for less than 0.8
seconds to play the next song.
o Push [SEEK
] button for 0.8 or longer to initiate high speed sound search of current song.
6. INFO Button Displays the information of the current CD TRACK in the order of DISC TITLE ➟DISC ARTIST➟TRACK TITLE➟ TRACK ART- IST ➟TOTAL TRACK➟ Play Screen ➟DISC TITLE➟···.(not displayed if the information is not available on the DISC.)
7. TUNE/ENTER Button Turn this button clockwise to display songs after current song. Also, turn this button counterclockwise to display songs before current song. To listen to the displayed song, press the button to skip to the song and play.
FEATURES OF YOUR HYUNDAI
117117117117117
Pressing the changes the BASS, MIDR- ANGE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Audio control knob clockwise or counter- clockwise.
o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.
o MID-RANGE Control To increase the MID-RANGE, rotate the knob clockwise, while to decrease the MID-RANGE, rotate the knob counterclock- wise.
o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.
o FADER Control Turn the control knob clockwise to emph- asize rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).
11. FOLDER Button Folder up/down operation. o Folder is moved up or down from cur- rently playing and folder name becomes displayed.
o Press enter key to play the selected
folder.
o If the enter key is not pressed with in 5
seconds, then the previous folder name
will be displayed again.
1FEATURES OF YOUR HYUNDAI
118
o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).
8. RANDOM Play Button Turns on/off the randomization of the play list of files in the currently played DISC. To cancel the mode, press the key once again.
9. REPEAT Button Repeats current song when the button is pressed for less than 0.8 seconds. Repeats the entire DISC when the button is pressed for 0.8 seconds or longer.
10. SCAN Play Button Plays first 10 seconds of each song in the DISC. To cancel the mode, press the key once again.
PA760E01JM-GAT
RADIO, SET UP, VOLUME CONTROL (PA 760S) (If installed)
FEATURES OF YOUR HYUNDAI
119119119119119
1. FM Selection Button 2. AM Selection Button 3. XM Selection Button 4. CD/AUX Selection Button 5. Automatic Channel Selection Button 6. Power ON/OFF 7. MUTE Button 8. SCAN Button 9. Information Display Button 10. SET UP Button 11. TUNE/ENTER Button 12. CAT(FLDR) Button 13. Preset Button
10
12
11
13
A-300JMU
1FEATURES OF YOUR HYUNDAI
120
1. FM Selection Button Turns to FM mode and toggles FM1 and FM2 when the button is pressed each time.
2. AM Selection Button Turns to AM mode, and toggles in the order of AM1➟AM2➟···➟AM1···when the button is pressed each time.
3. XM Selection Button Turns to XM mode, and toggles in the order of XM1➟XM2➟XM3➟···➟XM1··· when the button is pressed each time.
4. CD/AUX Selection Button If there is a cd in the CDP DECK it turns to CD mode, and if a device is connected to AUX then it toggles. CD➟AUX➟CD··· when the button is pressed each time.(It will not turn to AUX if the auxiliary device is not connected)
5. Automatic Channel Selection
Button
o When the [SEEK
]button is pressed, it reduces the band frequency by 200khz to automatically select channel. Stops at the previous frequency if no channel is found.
o When the [SEEK
]button is pressed, it increases the band frequency by 50khz to automatically select channel. Stops at the previous frequency if no channel is found.
6. Power ON/OFF & Volume Control
Button
Turns on/off the set when the IGNITION SWITCH is on ACC or ON. If the button is turned to the right, it increases the volume and left, decreases the volume.
7. MUTE Button Press to temporarily cut off the Sound.
8. SCAN Button If this button is pressed, the frequencies will become increased and receive the corresponding broadcasts. This function will play the frequencies for 5 seconds (XM MODE : 10 seconds) each and find other broadcasts as the frequency increases.
Press the button again when desiring to continue listening to the currently playing broadcast.
9. Information Display Button Information Display function operation (In- formation is displayed each time (the) Key is pressed) : Pressing the Category ➟Channel Name ➟Artist Name➟Song Title➟Category-KEY for 3 seconds will display the corresponding text then be- come restored. Text Scroll operation : After pressing (the) Key, if the text to be displayed is longer than the LCD text line, then rotating the Tune Knob will operate the Page up function displaying 8 charac- ters for 3 seconds each - displays the maximum lines of text supported by XM.
10. SET UP Button Press this button to turn to the XMoption, SCROLL and adjustment mode. If no action is taken for 5 seconds after pressing the button, it will return to the play mode.(After entering SET UP mode, move between items using the left, right and PUSH functions of the TUNE button.) The set up item changes from AUDIO ad- justment, TEXT SCROLL, XM setup.
11. TUNE/ENTER Button Turn this button clockwise by one notch to increase frequency by 0.05Mhz from cur- rent frequency. Turn this button counterclockwise by one notch to decrease frequency by 0.05Mhz from current frequency. Press this button while holding SET UP button to activate / inactivate the item to. Select SET UP item using left and right function of the Tune button.
Pressing the changes the BASS, MIDR- ANGE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Audio control knob clockwise or counter- clockwise.
o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.
o MID-RANGE Control To increase the MID-RANGE, rotate the knob clockwise, while to decrease the MID-RANGE, rotate the knob counterclock- wise.
o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.
o FADER Control Turn the control knob clockwise to emph- asize rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).
o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).
] Button when Category Up
12. CAT(FLDR) Button
Moves [CAT
search operation.
o Category is moved Up from the cat-
egory currently being received and
Category Name becomes displayed.
o If the Enter Key is not pressed within 5
seconds, then the previous mode will
be restored.
FEATURES OF YOUR HYUNDAI
121121121121121
o If the Key is pressed while in the last Category, then the first category will become displayed and operation will be repeated.
o Corresponding category can be se-
lected by pressing ENTER.
] Button when Category
Moves [CAT
Down search operation.
o Category is moved Down from the cat-
egory currently being received and
Category Name becomes displayed.
o If the Enter Key is not pressed within 5
seconds, then the previous mode will
be restored.
o If the [CAT
] Key is pressed while in the first Category, then the last category will become displayed and operation will be repeated.
o Corresponding category can be se-
lected by pressing ENTER.
13. Preset Button Push [1]~[6] buttons less than 0.8 seconds to play the channel saved in each button. Push pre-set button for 0.8 seconds or longer to save current channel to the re- spective button with a beep.
1FEATURES OF YOUR HYUNDAI
122
PA760F01JM-GAT
CDC (PA 760S) (If installed)
11
1. CD Loading Slot 2. CD Eject Button 3. LOAD Button 4. CD/AUX Selection Button 5. Automatic Track Selection Button 6. INFO Button 7. TUNE/ENTER Button 8. RANDOM Play Button 9. REPEAT Button 10. DISC Selection Button 11. SCAN Play Button 12. FOLDER Button
12
10
A-301JMU
1. CD Loading Slot Please face printed side upward and gen- tly push in. When the ignition switch is on ACC or ON and power is off, power is automatically turned on if the CD is loaded. This CDP supports both 8cm and 12 cm CDs. But if VCD, Data CD, MP3 CD are loaded, "Er-6" message will appear and CD will be ejected.
2. CD Eject Button Push button to eject the CD during CD playback. This button is enabled when ignition switch is off.
3. CD LOAD Button Push [LOAD] button to load CDs to avail- able CDC deck (from 1~6). Push [LOAD] button for more than 2 seconds to load into all available decks. The last CD will play. 10 seconds idle status will disable loading process.
4. CD/AUX Selection Button If the auxiliary device is connected, it turns to AUX MODE to play the sound from the auxiliary player. If no auxiliary device is connected, it dis- plays ""NO MEDIA"" for 5 seconds and returns to the previous mode."
5. Automatic Track Selection Button
o Push [SEEK
] button for less than 0.8
seconds to play from the beginning of
current song.
o Push [SEEK
] button for less than 0.8
seconds and press again within 1 sec-
onds to play the previous song.
o Push [SEEK
] button for 0.8 or longer to initiate reverse direction high speed sound search of current song.
o Push [SEEK
] button for less than 0.8
seconds to play the next song.
o Push [SEEK
] button for 0.8 or longer to initiate high speed sound search of current song.
6. INFO Button Displays the information of the current CD TRACK in the order of DISC TITLE ➟DISC ARTIST➟TRACK TITLE➟ TRACK ARTIST➟TOTAL TRACK➟Play Screen ➟DISC TITLE➟···.(not displayed if the in- formation is not available on the DISC.)
7. TUNE/ENTER Button Turn this button clockwise to display songs after current song. Also, turn this button counterclockwise to display songs before current song. To listen to the displayed song, press the button to skip to the song and play.
FEATURES OF YOUR HYUNDAI
123123123123123
Pressing the changes the BASS, MIDR- ANGE, TREBLE, FADER and BALANCE TUNE mode. The mode selected is shown on the dis- play. After selecting each mode, rotate the Audio control knob clockwise or counter- clockwise.
o BASS Control To increase the BASS, rotate the knob clockwise, while to decrease the BASS, rotate the knob counterclockwise.
o MID-RANGE Control To increase the MID-RANGE, rotate the knob clockwise, while to decrease the MID-RANGE, rotate the knob counterclock- wise.
o TREBLE Control To increase the TREBLE, rotate the knob clockwise, while to decrease the TREBLE, rotate the knob counterclockwise.
o FADER Control Turn the control knob clockwise to emph- asize rear speaker sound (front speaker sound will be attenuated). When the con- trol knob is turned counterclockwise, front speaker sound will be emphasized (rear speaker sound will be attenuated).
1FEATURES OF YOUR HYUNDAI
124
o BALANCE Control Rotate the knob clockwise to emphasize right speaker sound (left speaker sound will be attenuated). When the control knob is turned counter clockwise, left speaker sound will be emphasized (right speaker sound will be attenuated).
8. RANDOM Play Button Turns on/off the randomization of the play list of files in the currently played DISC. To cancel the mode, press the key once again.
9. REPEAT Button Repeats current song when the button is pressed for less than 0.8 seconds. Repeats the entire DISC when the button is pressed for 0.8 seconds or longer.
10. DISC Selection Button o [DISC
] Change Button
Changes disc to the previous disc.
o [DISC
] Change Button
Changes disc to the next disc.
11. SCAN Play Button Plays first 10 seconds of each song in the DISC. To cancel the mode, press the key once again.