2009 Hyundai Tucson Owners Manual

Example 3

DRIVING YOUR HYUNDAI

31

Item

Description

Vehicle Capacity Weight

C190F01JM

Total

1400 lbs

(635 kg)

Item

Description

Vehicle Capacity Weight

C190F02JM

Total

1400 lbs

(635 kg)

Item

Description

Vehicle Capacity Weight

C190F03JM

Total

1400 lbs

(635 kg)

Subtract Occupant Weight

300 lbs

150 lbs (68 kg) × 2

Available Cargo and

Luggage weight

(136 kg)

1100 lbs

(498 kg)

Subtract Occupant Weight

750 lbs

150 lbs (68 kg) x 5

Available Cargo and

Luggage Weight

(340 kg)

650 lbs

(295 kg)

Subtract Occupant Weight

860 lbs

172 lbs (78 kg) x 5

Available Cargo Weight

(390 kg)

540 lbs

(245 kg)

2 DRIVING YOUR HYUNDAI 32

Refer to your vehicle's tire and loading information label for specific informa- tion about your vehicle's capacity weight and seating positions. The combined weight of the driver, passengers and cargo should never exceed your vehicle's capacity weight.

C190G03JM-AAT

Compliance Label

C190G01JM The compliance label is located on the driver's side of the center piller outer panel.

The label shows the maximum allow- able weight of the fully loaded vehicle. This is called the GVWR (Gross Ve- hicle Weight Rating). The GVWR in- cludes the weight of the vehicle, all occupants, fuel and cargo.

This label also tells you the maximum weights that can be supported by the front and rear axles, called Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle. Your dealer can help you with this. Be sure to spread out your load equally on both sides of the centerline.

WARNING:

o Never exceed the GVWR for your vehicle, the GAWR for either the front or rear axle and vehicle ca- pacity weight. Exceeding these rat- ings can cause an accident or vehicle damage. You can calcu- late the weight of your load by weighing the items (or people) before putting them in the vehicle. Be careful not to overload your vehicle.

! WARNING:

o Do not load your vehicle any heavier than the GVWR, either the maximum front or rear GAWR and vehicle capacity weight. If you do, parts, including tires on your ve- hicle can break, and it can change the way your vehicle handles and braking ability. This could cause you to lose control and crash. Also, overloading can shorten the life of your vehicle.

WARNING:

o Overloading your vehicle can cause heat buildup in your vehicle's tires and possible tire failure that could lead to a crash. o Overloading your vehicle can cause increased stopping dis- tances that could lead to a crash. o A crash resulting from poor han- dling vehicle damage, tire failure, or increased stopping distances could result in serious injury or death.

DRIVING YOUR HYUNDAI

33

NOTE: o Overloading your vehicle may cause damage. Repairs would not be covered by your warranty. Do not overload your vehicle.

o Using heavier suspension com- ponents to get added durability might not change your weight rat- ings. Ask your dealer to help you load your vehicle the right way.

The label will help you decide how much cargo and installed equipment your vehicle can carry.

If you carry items inside your vehicle – like suitcases, tools, packages, or any- thing else – they more as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, the items will keep going and can cause an injury if they strikes the driver or a passenger.

2 DRIVING YOUR HYUNDAI 34

! WARNING:

Items you carry inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash.

o Put things in the cargo area of your vehicle. Try to spread the weight evenly.

o Never stack items, like suitcases, inside the vehicle above the tops of the seats.

o Do not leave an unsecured child

restraint in your vehicle.

o When you carry something inside

the vehicle, secure it.

o Do not drive with a seat folded

down unless necessary.

WHAT TO DO IN AN EMERGENCY

If the Engine will not Start .............................................. 3-2
Jump Starting ................................................................ 3-3
If the Engine Overheats ................................................ 3-4
Tire Pressure Monitoring System (TPMS) .................... 3-5
Spare Tire ..................................................................... 3-9
If You Have a Flat Tire ................................................ 3-10
Changing a Flat Tire .................................................... 3-11
If Your Car Must be Towed ......................................... 3-16
Emergency Towing ..................................................... 3-18

If You Lose Your Keys ................................................ 3-19 33

3

WHAT TO DO IN AN EMERGENCY

IF THE ENGINE WILL NOT START

D010A01A-AAT

WARNING:

If the engine will not start, do not push or pull the car to start it. This could result in a collision or cause other damage. In addition, push or pull starting may cause the catalytic converter to be overloaded and create a fire hazard.

D010B02A-AAT

If Engine Doesn't Turn Over or Turns Over Slowly

D010C02Y-AAT

If Engine Turns Over Normally but Does Not Start 1. Check fuel level. 2. With the key in the "OFF" position, check all connectors at ignition, coil and spark plugs. Reconnect any that may be dis- connected or loose.

3. Check the fuel line in the engine com-

partment.

4. If the engine still does not start, call a Hyundai dealer or seek other qualified assistance.

HJM5008
1. If your car has an automatic transaxle, be sure the gear selector lever is in "N" or "P" and the emergency brake is set. 2. Check the battery connections to be

sure they are clean and tight.

3. Turn on the interior light. If the light dims or goes out when you operate the starter, the battery is discharged.

4. Check the starter connections to be

sure they are securely tightened.

5. Do not push or pull the vehicle to start it.

See instructions for "Jump Starting".

D010D01A-AAT

If Engine Stalls While Driving 1. Reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place.

2. Turn on your emergency flashers. 3. Try to start the engine again. If your ve- hicle will not start, contact a Hyundai dealer or seek other qualified assistance.

D010F01A-AAT

If the engine stalls at a crossroad or crossing If the engine stalls at a crossroad or cross- ing, set the shift lever in the N(Neutral) position and then push the vehicle to a safe place.

JUMP STARTING

D020A03A-AAT

Discharged battery

Booster battery

HJM4001

WARNING:

The gas produced by the battery during the jump-start operation is highly explo- sive. If these instructions are not fol- lowed exactly, serious personal injury and damage to the vehicle may occur! If you are not sure how to follow this proce- dure, seek qualified assistance. Auto- mobile batteries contain sulfuric acid. This is poisonous and highly corrosive. When jump starting, wear protective glasses and be careful not to get acid on yourself, your clothing or on the car.

o If you should accidentally get acid on your skin or in your eyes, immediately remove any contaminated clothing and flush the area with clear water for at least 15 minutes. Then promptly obtain medical attention. If you must be trans- ported to an emergency facility, con- tinue to apply water to the affected area with a sponge or cloth.

o The gas produced by the battery during the jump-start operation is highly explo- sive. Do not smoke or allow a spark or an open flame in the vicinity.

o The battery being used to provide the jump start must be 12-volt. If you cannot determine that it is a 12-volt battery, do not attempt to use it for the jump start. o To jump start a car with a discharged battery, follow this procedure exactly:

1. If the booster battery is installed in an- other vehicle, be sure the two vehicles are not touching.

2. Turn off all unnecessary lights and

acces-sories in both vehicles.

3. Attach the clamps of the jumper cable in the exact location shown on the illustra- tion. First, attach one clamp of the jumper cable to the positive (+) post or cable of the discharged battery.

WHAT TO DO IN AN EMERGENCY

Then attach the other end of the same cable to the positive (+) post or cable of the booster battery. Next, using the other cable, attach one clamp to the negative (-) post or cable of the booster battery. Then attach the other end of that cable to a solid metal part of the engine of the vehicle with the discharged battery away from the battery. Do not connect the cable to any moving part.

4. Start the engine in the car with the booster battery and let it run for a few minutes. This will help to assure that the booster battery is fully charged. During the jumping operation, run the engine in this vehicle at about 2,000 rpm.

5. Start the engine in the car with the discharged battery using the normal starting procedure. After the engine starts, leave the jumper cables con- nected and let the engine run at fast idle or about 2,000 rpm for several minutes. 6. Carefully remove the jumper cables in

the reverse order of attachment.

If you do not know why your battery be- came discharged (because the lights were left on, etc.), have the charging system checked by your Hyundai dealer.

3

WHAT TO DO IN AN EMERGENCY

IF THE ENGINE OVERHEATS

D030A02A-AAT If your temperature gauge indicates over- heating, you experience a loss of power, or hear loud pinging or knocking, the engine is probably too hot. If this happens, you should:

1. Pull off the road and stop as soon as it

is safe to do so.

2. Place the gear selector lever in "P" (auto-matic), or neutral (manual transaxle) and set the parking brake. If the air conditioning is on, turn it off.

3. If engine coolant is running out under the car or steam is coming out from the hood, stop the engine. Do not open the hood until the coolant has stopped running or the steaming has stopped. If there is no visible loss of engine coolant and no steam, leave the engine running and check to be sure the engine cooling fan is operating. If the fan is not running, turn the engine off.

4. Check to see if the water pump drive belt is missing. If it is not missing, check to see that it is tight. If the drive belt seems to be satisfactory, check for coolant leaking from the radiator, hoses or un- der the car. (If the air conditioning had been in use, it is normal for cold water to be draining from it when you stop).

WARNING:

While the engine is running, keep hair, hands and clothing away from moving parts such as the fan and drive belts to prevent injury.

5. If the water pump drive belt is broken or engine coolant is leaking out, stop the engine immediately and call the near- est Hyundai dealer for assistance.

WARNING:

Do not remove the radiator cap when the engine is hot. This can allow coolant to be blown out of the opening and cause se- rious burns.

6. If you cannot find the cause of the over- heat-ing, wait until the engine tempera- ture has returned to normal. Then, if coolant has been lost, carefully add coolant to the reservoir (page 6-9) to bring the fluid level in the reservoir up to the halfway mark.

7. Proceed with caution, keeping alert for further signs of overheating. If over- heating happens again, call a Hyundai dealer for assistance.

CAUTION:

Serious loss of coolant indicates there is a leak in the cooling system and this should be checked as soon as possible by a Hyundai dealer.

TIRE PRESSURE MONITORING SYSTEM (TPMS)

C320A02JM-AAT

(If installed)

➀ Low Tire Pressure Telltale ➁ TPMS Malfunction Indicator

C320A01JM

Each tire, including the spare (if pro- vided), should be checked monthly when cold and inflated to the inflation pres- sure recommended by the vehicle manu- facturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should de- termine the proper tire inflation pres- sure for those tires.)

WHAT TO DO IN AN EMERGENCY

Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operat- ing properly. The TPMS malfunction indicator is provided by a separate tell- tale, which displays the symbol "TPMS" when illuminated. When the malfunc- tion indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS mal- functions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after re- placing one or more tires or wheels on your vehicle to ensure that the replace- ment or alternate tires and wheels allow the TPMS to continue to function prop- erly.

As an added safety feature, your ve- hicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure tell- tale when one or more of your tires is significantly under-inflated. Accord- ingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s han- dling and stopping ability.

Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.

WHAT TO DO IN AN EMERGENCY

Low tire pressure telltale

When the tire pressure monitoring sys- tem warning telltale is illuminated, one or more of your tires is significantly under-inflated. Immediately reduce your speed, avoid hard cornering and anticipate increased stopping distances. You should stop and check your tires as soon as pos- sible. Inflate the tires to the proper pressure as indicated on the vehicle’s placard or tire inflation pressure label located on the driver’s side center pillar outer panel. If you cannot reach a ser- vice station or if the tire cannot hold the newly added air, replace the low pres- sure tire with the temporary spare tire. Then the TPMS malfunction indicator may turn on and the Low Tire Pressure telltale may turn off after restarting and about 20 minutes of continuous driving before you have the low-pressure tire repaired and replaced on the vehicle.

CAUTION - Changing tem-

peratures

In winter or cold weather, the low tire pressure telltale may be illuminated if the tire pressure was adjusted to the recommended tire inflation pres- sure in warm weather. It does not mean your TPMS is malfunctioning because the decreased temperature leads to a proportional lowering of tire pressure. When you drive your vehicle from a warm area to a cold area or from a cold area to a warm area, or the outside temperature is greatly higher or lower, you should check the tire inflation pressure and adjust the tires to the recommended tire inflation pressure.

WARNING - Low pressure

damage

Significantly low tire pressure makes the vehicle unstable and can contrib- ute to loss of vehicle control and increased braking distances. Continued driving on low pressure tires can cause the tires to overheat and fail.

TPMS (Tire pressure moni- toring system) malfunction indicator

The TPMS malfunction indicator turns on and stays on when there is a problem with the Tire Pressure Monitoring Sys- tem. If the system is able to correctly detect an under-inflation warning at the same time as system failure then it will illuminate both the TPMS malfunction and the low tire pressure telltale e. g. if Front Left sensor fails, the TPMS mal- function indicator turns on, but if Front

Right, Rear Left, or Rear Right tire is under-inflated, the low tire pressure tell- tale may turn on at the same time as the TPMS malfunction indicator. Have the system checked by an autho- rized Hyundai dealer as soon as pos- sible to determine the cause of the problem.

NOTE: o The TPMS malfunction indicator may be illuminated if the vehicle is moving around electric power supply cable or radio transmitter such as police stations, govern- ment and public offices, broad- casting stations, military installa- tions, airports, or transmitting tower, etc. which can interfere with normal operation of the Tire Pres- sure Monitoring System (TPMS). o The TPMS malfunction indicator may be illuminated if snow chains or some electronic devices, such as notebook computer, are used in the vehicle. This can interfere with normal operation of the Tire Pressure Monitoring System (TPMS).

o If there is a failed tire sensor, it is possible for the TPMS to tempo- rarily learn a replacement sensor if closely driven to another ve- hicle that is also equipped with TPMS. In rare cases, this may temporarily delay the TPMS mal- function indicator from turning on.

Changing a tire with TPMS If you have a flat tire, the Low Tire Pressure telltale will turn on. Have the flat tire repaired by an authorized Hyundai dealer as soon as possible or replace the flat tire with the temporary spare tire.

NOTE: NEVER use a puncture-repairing agent to repair and/or inflate a low pressure tire. If used, you will have to replace the tire pressure sensor.

WHAT TO DO IN AN EMERGENCY

Each wheel is equipped with a tire pressure sensor mounted inside the tire behind the valve stem. You must use TPMS specific wheels. It is recommended that you always have your tires serviced by an autho- rized Hyundai dealer as soon as pos- sible. After you replace the low pressure tire with the temporary spare tire, the TPMS malfunction indicator may illuminate after restarting and about 20 minutes of continuous driving. Once the low pressure tire is re-inflated to the recommended pressure and in- stalled on the vehicle, the TPMS mal- function indicator and the low tire pres- sure telltale will be soon extinguished. If the low pressure and TPMS malfunc- tion indicators are not extinguished af- ter about 20 minutes of continuous driving, please visit an authorized Hyundai dealer. You may not be able to identify a low tire by simply looking at it. Always use a good quality tire pressure gauge to measure the tire's inflation pressure.

WHAT TO DO IN AN EMERGENCY

Please note that a tire that is hot (from being driven) will have a higher pres- sure measurement than a tire that is cold (from sitting stationary for at least 3 hours and driven less than 1 mile (1.6
km) during that 3 hour period). Allow the tire to cool before measuring the infla- tion pressure. Always be sure the tire is cold before inflating to the recommended pressure. A cold tire means the vehicle has been sitting for 3 hours and driven for less than 1 mile (1.6 km) in that 3 hour period.

CAUTION:

Do not use any tire sealant if your vehicle is equipped with a Tire Pres- sure Monitoring System. The liquid sealant can damage the tire pressure sensors. In order for the system to correctly monitor tires for under-inflation, there should be a total of exactly 4
sensors fitted to each of the four driven wheel positions.

There should be no other sensors in the vehicle including spare tire po- sition since this could cause the system to monitor the wrong sen- sors.

WARNING - TPMS

o The TPMS cannot alert you to se- vere and sudden tire damage caused by external factors such as nails or road debris.

o If you feel any vehicle instability, immediately take your foot off the accelerator, apply the brakes gradually and with light force, and slowly move to a safe position off the road.

WARNING - Protecting TPMS Tampering with, modifying, or dis- abling the Tire Pressure Monitoring System (TPMS) components may in- terfere with the system's ability to warn the driver of low tire pressure condi- tions and/or TPMS malfunctions.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful

interference, and

2. This device must accept any interfer- ence received, including interference that may cause undesired operation.

WARNING:

Changes or modifications not ex- pressly approved by the party re- sponsible for compliance could void the user’s authority to operate the equipment.

WHAT TO DO IN AN EMERGENCY

WARNING:

The temporary spare tire is for emer- gency use only. Do not operate your vehicle on this temporary spare at speeds over 50 mph (80 kmh). The original tire should be repaired or replaced as soon as is possible to avoid failure of the spare possibly leading to personal injury or death.

SPARE TIRE

D040A02JM-AAT

TEMPORARY SPARE TIRE The following instructions for the tem- porary spare tire should be observed:

1. Check inflation pressure as soon as practical after installing the spare tire, and adjust to the specified pres- sure. The tire pressure should be periodically checked and maintained at the specified pressure while the tire is stored.

Spare Tire Pressure

Tire Size

Type A Type B, C

T155/90R16
T155/90D16

Inflation Pressure 60 psi (420 kPa) 2. The spare tire should only be used temporarily and should be returned to the luggage compartment as soon as the original tire can be repaired or replaced.

3. Continuous use at speeds of over 50
mph (80 km/h) is not recommended.

4. As the temporary spare tire is spe- cifically designed for your vehicle, it should not be used on any other vehicle.

5. The temporary spare tire should not be used on any other wheels, nor should standard tires, snow tires, wheel covers or trim rings be used with the temporary spare wheel. If such use is attempted, damage to these items or other car components may occur.

6. The temporary spare tire pressure should be checked once a month while the tire is stored.

CAUTION:

o Do not use snow chains with your

temporary spare tire.

o Do not use more than one tempo-

rary spare tire at a time.

o Do not tow a trailer while the tem-

porary spare tire is installed.

WHAT TO DO IN AN EMERGENCY

10

D040B02JM-GAT

Handling the Spare Tire

To remove the spare tire

HJM2168-1

1. Open the tail gate. 2. Remove the luggage mat. 3. Remove the luggage under tray.

HJM4008

4. Turn the installation bolt counter- clockwise with a wheel nut wrench to remove the spare tire. After replac- ing the spare tire, install and tighten the bolt firmly with your fingers until there is no more play in the spare tire.

IF YOU HAVE A FLAT TIRE

D050A02A-AAT If a tire goes flat while you are driving: 1. Take your foot off the accelerator pedal and let the car slow down while driving straight ahead. Do not apply the brakes immediately or attempt to pull off the road as this may cause a loss of control. When the vehicle has slowed to such a speed that it is safe to do so, brake carefully and pull off the road. Drive off the road as far as possible and park on firm, level ground. If you are on a divided high- way, do not park in the median area between the two traffic lanes.

2. When the car is stopped, turn on your emergency hazard flashers, set the parking brake and put the transaxle in "P" (automatic) or reverse (manual transaxle).

3. Have all passengers get out of the vehicle. Be sure they all get out on the side of the vehicle that is away from traffic.

4. Change the tire following the instruc- tions provided on the following pages.

CHANGING A FLAT TIRE

D060A02HP-AAT

D060A01JM The procedure described on the follow- ing pages can be used to rotate tires as well as to change a flat tire. When preparing to change a flat tire, check to be sure the gear selector lever is in "P" (automatic) or reverse gear (manual transaxle) and that the parking brake is set, then:

! WARNING:

Your vehicle is equipped with tires designed to provide for safe ride and handling capability. Do not use a size and type of tire and wheel that is different from the one that is originally installed on your vehicle. It can affect the safety and performance of your vehicle, which could lead to handling failure or rollover and serious injury. When replacing the tires, be sure to equip all four tires with the tire and wheel of the same size, type, tread, brand and load-carrying capacity. If you nevertheless decide to equip your vehicle with any tire/wheel com- bination not recommended by Hyundai for off-road driving, you should not use these tires for high- way driving.

WHAT TO DO IN AN EMERGENCY

11

D060B01JM-AAT

1. Obtain Spare Tire and Tool

HJM4007
Remove the spare tire and remove the jack and tool bag from the luggage compartment.

NOTE: The spare tire is located under the luggage compartment floor.

WHAT TO DO IN AN EMERGENCY

12

D060C02A-AAT

2. Block the Wheel

Flat tire

D060D01A-AAT

3. Loosen Wheel Nuts

D060E01A-AAT

4. Put the Jack in Place

HJM4009
Block the wheel that is diagonally oppo- site from the flat to keep the vehicle from rolling when the vehicle is raised on the jack.

HJM4015
The wheel nuts should be loosened slightly before raising the car. To loosen the nuts, turn the wrench handle coun- terclockwise. When doing this, be sure that the socket is seated completely over the nut so it cannot slip off. For maximum leverage, position the wrench so the handle is to the left as shown in the drawing. Then, while holding the wrench near the end of the handle, push down on it with steady pressure. Do not remove the nuts at this time. Just loosen them about one-half turn.

HJM4010
The base of the jack should be placed on firm, level ground. The jack should be positioned as shown in the drawing.

Raise the car high enough so that the fully inflated spare tire can be installed. To do this, you will need more ground clearance than is required to remove the flat tire.

WARNING:

Do not get under the vehicle when it is supported by the jack! This is very dangerous as the vehicle could fall and cause serious injury or death. No one should stay in the vehicle while the jack is being used.

D060F03E-AAT

5. Raising the vehicle

Wrench bar

Wheel nut wrench

HFC4022
After inserting the wrench bar into the wheel nut wrench, install the wrench bar into the jack as shown in the drawing. To raise the vehicle, turn the wheel nut wrench clockwise. As the jack begins to raise the vehicle, double check that it is properly positioned and will not slip. If the jack is on soft ground or sand, place a board, brick, flat stone or other object under the base of the jack to keep it from sinking.

WHAT TO DO IN AN EMERGENCY

13

D060G01JM-AAT

6. Changing Wheels

D060G01JM Loosen the wheel nuts and remove them. Slide the wheel off the studs and lay it flat so it cannot roll away. To put the wheel on the hub, pick up the spare tire, line up the holes with the studs and slide the wheel onto them. If this is difficult, tip the wheel slightly and get the top hole in the wheel lined up with the top stud. Then jiggle the wheel back and forth until the wheel can be slid over the other studs.

WHAT TO DO IN AN EMERGENCY

14

WARNING:

Wheels and wheel covers may have sharp edges. Handle them carefully to avoid possible severe injury. Be- fore putting the wheel into place, be sure that there is nothing on the hub or wheel (such as mud, tar, gravel, etc.) that interferes with the wheel from fitting solidly against the hub. If there is, remove it. If there is not good contact on the mounting sur- face between the wheel and hub, the wheel nuts could come loose and cause the loss of a wheel. Loss of a wheel may result in loss of control of the vehicle. This may cause serious injury or death.

D060H03O-AAT

7. Reinstall Wheel Nuts

D060H01JM To reinstall the wheel, hold it on the studs, put the wheel nuts on the studs and tighten them finger tight. Jiggle the tire to be sure it is completely seated, then tighten the nuts as much as pos- sible with your fingers again.

D060G02JM

! WARNING:

If the vehicle has been driven re- cently, some pieces may be very hot. Use caution.

D060I01E-AAT

8. Lower Vehicle and Tighten Nuts

After changing wheels, have a techni- cian tighten the wheel nuts to their proper torque as soon as possible.

Wheel nut tightening torque: Steel wheel & aluminium alloy wheel: 65-80 lb.ft (900-1,100 kg.cm)

HJM4016

Lower the car to the ground by turning the wheel nut wrench counterclock- wise. Then position the wrench as shown in the drawing and tighten the wheel nuts. Be sure the socket is seated completely over the nut. Do not stand on the wrench handle or use an exten- sion pipe over the wrench handle. Go around the wheel tightening every other nut until they are all tight. Then double-check each nut for tightness.

WHAT TO DO IN AN EMERGENCY

15

D060J02O-AAT

After Changing Wheels

D060J01JM

If you have a tire gauge, remove the valve cap and check the air pressure. If the pressure is lower than recom- mended, drive slowly to the nearest service station and inflate to the correct pressure. If it is too high, adjust it until it is correct. Always reinstall the valve cap after checking or adjusting tire pressure. If the cap is not replaced, air may leak from the tire. If you lose a valve cap, buy another and install it as soon as possible.

WHAT TO DO IN AN EMERGENCY

16

After you have changed wheels, al- ways secure the flat tire in its place and return the jack and tools to their proper storage locations.

IF YOUR VEHICLE MUST BE TOWED

D080A01O-GAT If your vehicle has to be towed, it should be done by your Hyundai dealer or a commer- cial tow truck service. This will help assure that your vehicle is not damaged in towing. Also, professionals are generally aware of local laws governing towing. In any case, rather than risk damage to your car, it is suggested that you show this information to the tow truck operator. Be sure that a safety chain system is used and that all local laws are observed. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground.

CAUTION:

incorrectly!

o Your vehicle can be damaged if towed

o Be sure the transaxle is in neutral. o When the engine will not start, be sure the steering is unlocked by placing the key in the "ACC" position.

D080B01O-GAT

Towing the 2 Wheel Drive Vehicle

1)

2)

3)

dolly

D080B03JM Your vehicle can be towed by wheel lift type truck (1), (2) or flatbed equipment (3).

!

CAUTION:

o When towing the vehicle, take care not to cause damage to the bumper or underbody of the vehicle.

WHAT TO DO IN AN EMERGENCY

17

CAUTION:

1) If the vehicle is being towed with the rear wheels on the ground, be sure the park- ing brake is released.

NOTE: Before towing, check the level of the automatic transaxle fluid. If it is below the "HOT" range on the dipstick, add fluid. If you cannot add fluid, a towing dolly must be used.

D080A01JM

o Do not tow with sling type truck as this may cause damage to the bumper or underbody of the vehicle.

2) If any of the loaded wheels or suspen- sion components are damaged or the vehicle is being towed with the front wheels on the ground, use a towing dolly under the front wheels.

o Manual Transaxle:

If you do not use a towing dolly, place the ignition key in the "ACC" position and put the transaxle in "N (Neutral)".

CAUTION:

Do not tow with the key removed or in the "LOCK" position when towing from the rear without a towing dolly.

o Automatic Transaxle:

Be sure to use a towing dolly under the front wheels.

HJM4019

A vehicle with an automatic transaxle should never be towed from the rear with the front wheels on the ground. This can cause serious damage to the transaxle.

3) It is recommended that your vehicle be towed with all the wheels off the ground.

WHAT TO DO IN AN EMERGENCY

18

D080B02O-AAT

Towing the 4 Wheel Drive Vehicle

CAUTION:

o The 4WD vehicle should never be towed with the wheels on the ground. This can cause serious damage to the transaxle or the 4WD system.

o When towing the vehicle, take care not to cause damage to the bumper or underbody of the vehicle.

dolly

dolly

D080D02O-AAT

EMERGENCY TOWING

Towing Hooks

HJM4022

D080C04JM

When towing the 4WD vehicle, it must be towed by lifting all 4 wheels or using the towing dolly.

D080C03JM

o Do not tow with sling type truck as this may cause damage to the bumper or underbody of the vehicle.

Towing Hooks

HJM4023

WHAT TO DO IN AN EMERGENCY

IF YOU LOSE YOUR KEYS

19

D120A01A-AAT If you lose your keys, many Hyundai deal- ers can make you a new key if you have your key number. If you lock the keys inside your car and you cannot obtain a new key, many Hyundai dealers can use special tools to open the door for you.

For emergency towing when no commer- cial tow vehicle is available, attach a tow cable, chain or strap to one of the towing hooks under the front/rear of your vehicle. Be very careful when attempting this pro- cedure when the vehicle is on any un- paved surface to avoid damage to your vehicle. Nor should towing be attempted if the wheels, drive train, axles, steering or brakes are damaged. Before towing, be sure the transaxle is in neutral and the key is in "ACC" (with the engine off) or in the "ON" position (with the engine running). A driver must be in the towed vehicle to steer it and operate the brakes.

NOTE: o To avoid serious damage to your 4WD vehicle, limit the towing to 15 km/h (10
mph) and not for more than 1.5 km (1
mile) at ANY TIME.

o Before towing, check the level of the automatic transaxle fluid. If it is below the "75°C" range on the dipstick, add fluid. If you cannot add fluid, a towing dolly must be used.

CAUTION:

If the Engine is not running, the power assist for the brakes and steering will not work so steering and braking will be much harder than usual.

CAUTION:

If the car is being towed with all four wheels on the ground, it can be towed only from the front. Be sure that the transaxle is in neutral. Do not tow at speeds greater than 50 km/h (30 mph) and for more than 25 km (15 miles). Be sure the steering is unlocked by plac- ing the key in the "ACC" position. A driver must be in the towed vehicle to operate the steering and brakes.

CORROSION PREVENTION & APPEARANCE CARE

Corrosion Protection ..................................................... 4-2
To Help Prevent Corrosion ........................................... 4-2
Washing and Waxing .................................................... 4-3
Cleaning the Interior ...................................................... 4-5

4 CORROSION PREVENTION AND APPEARANCE CARE

CORROSION PROTECTION

E010A01A-AAT

Protecting Your Hyundai from Cor- rosion By using the most advanced design and construction practices to combat corro- sion, Hyundai produces cars of the highest quality. However, this is only part of the job. To achieve the long-term corrosion resis- tance your Hyundai can deliver, the owner's cooperation and assistance is also re- quired.

E010B01A-AAT

Common Causes of Corrosion The most common causes of corrosion on your car are:

o Road salt, dirt and moisture that is al- lowed to accumulate underneath the car.

o Removal of paint or protective coatings by stones, gravel, abrasion or minor scrapes and dents which leave unpro- tected metal exposed to corrosion.

E010C01A-AAT

High-Corrosion Areas If you live in an area where your car is regularly exposed to corrosive materials, corrosion protection is particularly impor- tant. Some of the common causes of accelerated corrosion are road salts, dust control chemicals, ocean air and industrial pollution.

E010D01A-AAT

Moisture Breeds Corrosion Moisture creates the conditions in which corrosion is most likely to occur. For ex- ample, corrosion is accelerated by high humidity, particularly when temperatures are just above freezing. In such conditions, the corrosive material is kept in contact with the car surfaces by moisture that is slow to evaporate. Mud is particularly corrosive because it is slow to dry and holds moisture in contact with the vehicle. Although the mud ap- pears to be dry, it can still retain the mois- ture and promote corrosion. High temperatures can also accelerate cor- rosion of parts that are not properly venti- lated so the moisture can be dispersed. For all these reasons, it is particularly important to keep your car clean and free of mud or accumulations of other materials. This ap- plies not only to the visible surfaces but particularly to the underside of the car.

TO HELP PREVENT CORRO- SION

E020A01A-AAT You can help prevent corrosion from get- ting started by observing the following:

E020B01A-AAT

Keep Your Car Clean The best way to prevent corrosion is to keep your car clean and free of corrosive materials. Attention to the underside of the car is particularly important.

o If you live in a high-corrosion area — where road salts are used, near the ocean, areas with industrial pollution, acid rain, etc.—, you should take extra care to prevent corrosion. In winter, hose off the underside of your car at least once a month and be sure to clean the underside thoroughly when winter is over.

o When cleaning underneath the car, give particular attention to the components under the fenders and other areas that are hidden from view. Do a thorough job; just dampening the accumulated mud rather than washing it away will accelerate corrosion rather than pre- vent it. Water under high pressure and steam are particularly effective in re- moving accumulated mud and corro- sive materials.

o When cleaning lower door panels, rocker panels and frame members, be sure that drain holes are kept open so that moisture can escape and not be trapped inside to ac-celerate corro- sion.

E020C02A-AAT

Keep Your Garage Dry Don't park your car in a damp, poorly ventilated garage. This creates a favor- able environment for corrosion. This is particularly true if you wash your car in the garage or drive it into the garage when it is still wet or covered with snow, ice or mud. Even a heated garage can contribute to corrosion unless it is well ventilated so moisture is dispersed.

CORROSION PREVENTION AND APPEARANCE CARE

WASHING AND WAXING

E020D02A-AAT

Keep Paint and Trim in Good Condi- tion Scratches or chips in the finish should be covered with "touch-up" paint as soon as possible to reduce the possibility of corro- sion. If bare metal is showing through, the attention of a qualified body and paint shop is recommended.

Bird droppings : Bird droppings are highly corrosive and may damage painted sur- faces in just a few hours. Always remove bird droppings as soon as possible.

E020E01A-AAT

Don't Neglect the Interior Moisture can collect under the floor mats and carpeting to cause corrosion. Check under the mats periodically to be sure the carpeting is dry. Use particular care if you carry fertilizers, cleaning materials or chemicals in the car. These should be carried only in proper containers and any spills or leaks should be cleaned up, flushed with clear water and thoroughly dried.

E030A03A-AAT

Washing Your Hyundai Never wash your car when the surface is hot from being in the sun. Always wash your car in the shade.

Wash your car frequently. Dirt is abrasive and can scratch the paint if it is not re- moved. Air pollution or acid rain may dam- age the paint and trim through chemical action if pollutants are allowed to remain in contact with the surface. If you live near the ocean or in an area where road salts or dust control chemicals are used, you should pay particular attention to the un- derside of the car. Start by rinsing the car to remove dust and loose dirt. In winter, or if you have driven through mud or muddy water, be sure to thoroughly clean the underside as well. Use a hard direct stream of water to remove accumulations of mud or corrosive materials. Use a good quality car-washing solution and follow the manufacturer's directions on the package. These are available at your Hyundai dealer or auto parts outlet. Don't use strong house- hold detergents, gasoline, strong solvents or abrasive cleaning powders as these may damage the finish.

4 CORROSION PREVENTION AND APPEARANCE CARE

Use a clean sponge or cloth, rinse it fre- quently and don't damage the finish by rubbing too hard. For stubborn spots, dampen them frequently and remove them a little at a time. To clean whitewall tires, use a stiff brush or soapy steel-wool scouring pad.

To clean plastic wheel covers, use a clean sponge or soft cloth and water.

To clean cast aluminum alloy wheels, use a mild soap or neutral detergent. Do not use abrasive cleaners. Protect the bare- metal surfaces by cleaning, polishing and waxing. Because aluminum is subject to corrosion, be sure to give aluminum alloy wheels special attention in winter. If you drive on salted roads, clean the wheels thoroughly afterwards.

After washing, be sure to rinse thoroughly. If soapy water dries on the finish, streaking will result.

When the weather is warm and the humid- ity low, you may find it necessary to rinse each section immediately after washing to avoid streaking.

After rinsing, dry the car using a damp chamois or soft, absorbent cloth. The rea- son for drying the car is to remove water from the car so it will dry without water spots. Don't rub, this can damage the fin- ish.

If you find any nicks or scratches in the paint, use touch-up paint to cover them to prevent corrosion. To protect the paintwork of the car against corrosion, you must clean your Hyundai (at least once a month). Give special attention to the removal of salt, mud and other sub- stances on the underside of the splashboards of the car. Make sure that the outlets and the underside of the doors are open. Paint damage can be caused by small accumulation of tar, industrial pre- cipitation, tree resin, insects and bird drop- pings, when not removed immediately. If water alone is not strong enough to re- move the accumulated dirt, use a mild car washing solution. Be sure to rinse the surface after washing to remove the solu- tion. Never allow the solution to dry on the painted surfaces.

CAUTION:

ojb037800
o Water washing in the engine compart- ment including high pressure water washing may cause the failure of elec- trical circuits located in the engine compartment.

o Never allow water or other liquids to come in contact with electrical/elec- tronic components inside the vehicle as this may damage them.

E030B01A-AAT

Spot Cleaning Don't use gasoline, strong solvents or cor- rosive cleaning agents. These can dam- age the finish of the car. To remove road tar, use turpentine on a clean, soft cloth. Be gentle. To remove dead insects or tree sap, use warm water and mild soap or car-washing solution. Soak the spot and rub gently. If the paint has lost its luster, use a commer- cial car-cleaning polish.

E030D01A-AAT

When to Wax Again You should polish and wax the car again when water no longer beads on a clean surface but spreads out over a larger area.

E030E01A-AAT

Maintaining Bumpers Special precautions must be observed to preserve the appearance of the bumpers on your Hyundai. They are:

CORROSION PREVENTION AND APPEARANCE CARE

CLEANING THE INTERIOR

E040A01A-AAT

To Clean the Vinyl Upholstery To clean the vinyl upholstery, first remove loose dirt and dust with a vacuum cleaner. Then apply a solution of mild soap or detergent and water using a clean sponge or soft cloth. Allow this to stay on the sur- face to loosen the dirt, then wipe with a clean damp sponge or cloth. If all the dirt stains are not removed, repeat this proce- dure until the upholstery is clean. Do not use gasoline, solvent, paint thinner or other strong cleaners.

E030C01A-AAT

Polishing and Waxing Always wash and dry the car before polish- ing or waxing or using a combination cleaner and wax. Use a good quality com- mercial product the manufacturer's directions on the container. Polish and wax the bright trim pieces as well as the paint.

follow

and

o Be careful not to spill battery electrolyte or hydraulic brake fluid on the bumpers. If you do, wash it off immediately with clear water.

o Be gentle when cleaning the bumper sur-faces. They are made of soft plastic and the surface can be damaged if mistreated. Do not use abrasive clean- ers. Use warm water and mild soap or car-washing solution.

o Do not expose the bumpers to high tem- peratures. For example, if you have your car repainted, do not leave the bumpers on the car if the car is going to be placed in a high-temperature paint booth.

ANY QUESTIONS?

E050A01A-AAT If you have any questions about the care of your car, consult your Hyundai dealer.

4 CORROSION PREVENTION AND APPEARANCE CARE

E040B01A-AAT

To Clean the Leather Upholstery (If installed) In the normal course of use, leather uphol- stered surfaces will, like any material, pick- up dust and dirt. This dust and dirt must be cleaned off or it may work into the surface of the leather, causing damage.

Fine leather needs care, and should be cleaned when necessary. Washing leather thoroughly with soap and water will keep your leather lustrous, beautiful and ensure you have many years of wear. Take a piece of cheese cloth and using any mild soap and lukewarm water, work up a good lather. Thoroughly wash the leather. Wipe clean with a slightly damp cloth and dry with soft cloth. Do this as often as the leather becomes soiled.

During tanning operations, sufficient oils are incorporated through processing that none need be applied during the life of the leather. Oil applied to the finished surface will in no way help the leather and may do more harm than good. Varnishes and fur- niture polishes should never be used un- der any conditions.

E040C01A-AAT

Cleaning the Carpets Use a foam-type carpet cleaner. Cleaners of this type are available in aerosol cans in liquid form or powder. Read the instruc- tions and follow them exactly. Using a vacuum cleaner with the appropriate at- tachment, remove as much dirt from the carpets as possible. Apply the foam follow- ing the manufacturer's directions, then rub in overlapping circles. Do not add water. These cleaners work best when the carpet is kept as dry as possible.

E040D01A-AAT

Cleaning the Seat Belts To clean the seat belts, use a cloth or sponge with mild soap or detergent and warm water. Do not use strong detergents, dye, bleach or abrasive materials on the seat belts as this may weaken the fabric. While cleaning the belts, inspect them for excessive wear, cuts, fraying or other signs of damage and replace them if necessary.

E040E01A-AAT

Cleaning the Windows You may use any household window cleaner on the windows. However, when cleaning the inside of the rear window be careful not to damage the rear window defroster wiring.

VEHICLE MAINTENANCE REQUIREMENTS

Maintenance Intervals ................................................... 5-2
Scheduled Maintenance ................................................ 5-4
Maintenance under Severe Usage Conditions ............. 5-6
Explanation of Scheduled Maintenance Items .............. 5-7
California Perchlorate Notice ...................................... 5-10

5 VEHICLE MAINTENANCE REQUIREMENTS

MAINTENANCE INTERVALS

F010A01A-AAT

Service Requirements To ensure that you receive the greatest number of miles of satisfying operation from your Hyundai, certain maintenance procedures must be performed. Although careful design and engineering have re- duced these to a minimum, those that are required are of the utmost importance. It is your responsibility to have these main- tenance procedures performed to comply with the terms of the warranties covering your new Hyundai. The Owner's Hand- book supplied with your new vehicle pro- vides further information about these war- ranties.

F010B01A-AAT

Maintenance Requirements The maintenance required for your Hyundai can be divided into three main areas:

o Specified scheduled procedures o General checks o Do-it-yourself maintenance

F010C01A-AAT

Specified Scheduled Procedures These are the procedures such as inspec- tions, adjustments and replacements that are listed in the maintenance charts start- ing on page 5-4. These procedures must be performed at the intervals shown in the maintenance schedule to assure that your warranty remains in effect. Although it is strongly recommended that they be per- formed by the trained technicians at your Hyundai dealer, these procedures may be performed at any qualified service facility. It is suggested that genuine Hyundai ser- vice parts be used for any required repairs or replacements. Other parts of equivalent quality such as engine oil, engine coolant, manual or auto transaxle oil, brake fluid and so on which are not supplied by Hyundai Motor Company or its distributor may be used without affecting your war- ranty coverage but you should always be sure these are equivalent to the quality of the original Hyundai parts. Your Owner's Handbook provides further information about your warranty coverage.

VEHICLE MAINTENANCE REQUIREMENTS

F010D02A-AAT

General Checks These are the regular checks you should perform when you drive your Hyundai or you fill the fuel tank. A list of these items will be found on page 6-4.

F010E01A-AAT

Do-It-Yourself Maintenance If you are mechanically inclined, own a few tools that are required and want to take the time to do so, you can inspect and service a number of items. For more information about doing it yourself, see Section 6.

F010F01A-AAT

A Few Tips o Whenever you have your Hyundai ser- viced, keep copies of the service records in your glovebox. This will help ensure that you can document that the required procedures have been performed to keep your warranties in effect. This is especially important when service is not performed by an authorized Hyundai dealer.

o If you choose to do your own mainte- nance and repairs, you may find it helpful to have an official Hyundai Shop Manual. A copy of this publication may be purchased at your Hyundai dealer's parts department.

F020A02Y-AAT

SCHEDULED MAINTENANCE REQUIREMENTS o Inspection should be performed any time a malfunction is experienced or suspected.

o Receipts for all emission control system services should be retained to demon- strate compliance with conditions of the emissions system warranty.

o After 120 months or 150,000 miles (240,000 km), continue to follow the prescribed maintenance intervals.

o For severe usage maintenance require-

ments, see page 5-6 of this section.

5 VEHICLE MAINTENANCE REQUIREMENTS

SCHEDULED MAINTENANCE

F030A01A-AAT The following maintenance services must be performed to ensure good emission control and performance. Keep receipts for all vehicle emission services to protect your warranty. Where both mileage and time are shown, the frequency of service is determined by whichever occurs first.

F030B03JM-AAT R :Replace I : Inspect and, after Inspection, clean, adjust, repair or replace if necessary.

No.

DESCRIPTION

KILOMETERS X 1000

MILES X 1000

MONTHS

7.5

12

15

24

12

22.5

36

18

30

48

24

37.5

45

52.5

60

30

72

36

84

42

60

96

48

67.5

75

82.5

90

97.5

105

112.5

120

127.5

135

142.5

150

108

120

132

144

156

168

180

192

204

216

228

240

54

60

66

72

78

84

90

96

102

108

114

120

EMISSION CONTROL ITEMS

ENGINE OIL AND FILTER

FUEL FILTER

FUEL LINES, FUEL HOSES AND CONNECTIONS

VACUUM HOSES

CRANKCASE VENTILATION HOSE

VAPOR HOSE AND FUEL FILLER CAP

AIR CLEANER FILTER

FUEL TANK AIR FILTER

SPARK PLUGS (PLATINUM COATED) - 2.0L

SPARK PLUGS (IRIDIUM COATED) - 2.7L

10

VALVE CLEARANCE (2.0L only)

R: 100.000 miles / 120 months

F030C03JM-AAT R : Replace I : Inspect and, after inspection, clean, adjust, repair or replace if necessary

VEHICLE MAINTENANCE REQUIREMENTS

No.

DESCRIPTION

MILES X 1000
KILOMETERS X 1000
MONTHS

GENERAL ITEMS DRIVE BELT

2.0 DOHC (ALT, W/PUMP) 2.7 V6 (ALT, P/STR'G, A/CON)

See Note (1)

COOLANT TIMING BELT (WHEN REPLACE TIMING BELT AND INSPECT WATER PUMP : 2.7L) (See Note (2)- 2.0 L) MANUAL TRANSAXLE OIL AUTOMATIC TRANSAXLE FLUID BRAKE FLUID BRAKE HOSES AND LINES REAR BRAKE DRUMS/LININGS, PARKING BRAKE BRAKE PADS, CALIPERS AND ROTORS EXHAUST PIPE AND MUFFLER SUSPENSION MOUNTING BOLTS