Index
Home
65
Safety Labels
Label Locations These labels are in the locations shown. They warn you of potential hazards that can cause serious injury or death. Read these labels carefully.
If a label comes off or becomes hard to read (except for the U.S. dashboard label which may be removed by the owner), contact a dealer for a replacement.
Sun Visor U.S. models
Canadian models
Sun Visor U.S. models only
Dashboard U.S. models only
Radiator Cap
Doorjambs
U.S. models
Canadian models
QRG
TOC
Index
Home
66
Instrument Panel
QRG
This chapter describes the buttons, indicators, and gauges that are used while driving.
Indicators ............................................ 68
Multi-Information Display Warning and
Information Messages*.................... 78
Gauges and Displays
Gauges.............................................. 80
Information Display*.......................... 81
Multi-Information Display *................. 85
Index
Home
67
* Not available on all models
Indicators
Indicator
Name
On/Blinking
Explanation
Message *
● Comes on for a few seconds
● Comes on while driving -
U.S.
Canada
when you turn the ignition switch to ON (w, then goes off.
● Comes on when the parking brake is applied, and goes off when it is released.
● Comes on when the brake
fluid level is low.
● Comes on if there is a
problem with the brake system.
● The beeper sounds and the
indicator comes on if you drive with the parking brake not fully released.
● Comes on when you turn the ignition switch to ON (w, and goes off when the engine starts.
● Comes on when the engine
oil pressure is low.
Make sure the parking brake is released. Check the brake fluid level.
2 What to do when the
indicator comes on while
driving P. 452
● Comes on along with the ABS
indicator - Have the vehicle checked by a dealer.
2 If the Brake System
Indicator (Red) Comes On
P. 452
● Comes on while driving -
Immediately stop in a safe place.
2 If the Low Oil Pressure
Indicator Comes On P. 450
QRG
TOC
U.S.
Canada
Parking Brake and Brake System Indicator (Red)
Low Oil Pressure Indicator
Index
Home
68
* Not available on all models
Indicator
Name
On/Blinking
Explanation
Message *
uuIndicatorsu
Malfunction Indicator Lamp
● Comes on when you turn the ignition switch to ON (w, and goes off either when the engine starts or after several seconds if the engine is not started. If “readiness codes” have not been set, it blinks five times before it goes off.
● Comes on if there is a problem with
the emissions control system.
● Blinks when a misfire in the engine's
cylinders is detected.
● Readiness codes are part of the on board
diagnostics for the emissions control systems.
2 Testing of Readiness Codes P. 470
● Comes on while driving - Have the
vehicle checked by a dealer.
● Blinks while driving - Stop in a safe place where there are no flammable objects. Stop the engine for 10 minutes or more, and wait for it to cool down. Then, take the vehicle to a dealer.
2 If the Malfunction Indicator Lamp
Comes On or Blinks P. 451
Charging System Indicator
● Comes on when you turn the ignition switch to ON (w, and goes off when the engine starts.
● Comes on when the battery is not
● Comes on while driving - Turn off the climate control system and rear defogger in order to reduce electricity consumption.
charging.
2 If the Charging System Indicator
Comes On P. 450
QRG
TOC
Shift Lever Position Indicator
● Indicates current shift lever position. (d indicator: ● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● Comes on when you press the (d button while the shift lever is in (D.
* Not available on all models
2 Shifting P. 346
—
Index
Home
Continued
69
QRG
TOC
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
Transmission Indicator
Seat Belt Reminder Indicator
● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● Blinks if the transmission system has a
problem.
● Comes on and the beeper sounds if you are not wearing a seat belt when you turn the ignition switch to ON (w. If the front passenger is not wearing a seat belt, the indicator comes on a few seconds later.
● Blinks while driving if either you or
the front passenger has not fastened a seat belt. The beeper sounds and the indicator blinks at regular intervals.
● Blinks while driving - Avoid sudden
starts and acceleration and have the vehicle checked by a dealer immediately.
● The beeper stops and the indicator goes
off when you and the front passenger fasten their seat belts.
● Stays on after you or the front
passenger has fastened the seat belt - A detection error may have occurred in the sensor. Have the vehicle checked by a dealer.
2 Seat Belt Reminder P. 30
Low Fuel Indicator
● Comes on when the fuel reserve is
● Comes on - Refuel your vehicle as soon
running low (approximately 2.8 U.S. gal./10.8 Liter).
as possible.
● Blinks - Have the vehicle checked by a
● Blinks if there is a problem with the
dealer.
fuel gauge.
Index
Home
70
* Not available on all models
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
ABS (Anti-lock Brake System) Indicator
● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● If it comes on at any other time, there
● Stays on constantly - Have the vehicle checked by a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function.
is a problem with the ABS.
2 ABS (Anti-lock Brake System) P. 362
Supplemental Restraint System Indicator
VTM-4® System Indicator *
● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● Comes on if a problem with any of
the following is detected: - Supplemental restraint system - Side airbag system - Side curtain airbag system - Seat belt tensioner
● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● Comes on if there is a problem with
the VTM-4®.
● Blinks when the VTM-4® system is overheated. The system is inactive.
● Stays on constantly or does not come on at all - Have the vehicle checked by a dealer.
● Stays on constantly - Have the vehicle
checked by a dealer.
● Blinks while driving - The VTM-4® fluid
temperature is too high. Stop in a safe place, shift to (P, and idle the engine until the indicator goes off. If the indicator does not stop blinking, take your vehicle to a dealer.
2 VTM (Variable Torque
Management)-4r System* P. 354
* Not available on all models
QRG
TOC
—
Index
Home
Continued
71
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
VSA® (Vehicle Stability Assist) System Indicator
● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● Blinks when VSA® is active. ● Comes on if there is a problem with
the VSA® system.
● Comes on if there is a problem with
the hill start assist system.
VSA® (Vehicle Stability Assist) OFF Indicator
● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● Comes on when you deactivate
VSA®.
Door Open Indicator
Door, Glass Hatch, and Tailgate Open Indicator *
● Comes on for a few seconds if you turn the ignition switch to ON (w, then goes off.
● Comes on if any door, glass hatch, or
tailgate is not completely closed.
● Comes on for a few seconds if you turn the ignition switch to ON (w, then goes off.
● Comes on if any door, glass hatch, or
tailgate is not completely closed.
● Stays on constantly - Have the vehicle
checked by a dealer.
2 VSA® (Vehicle Stability Assist), aka
ESC (Electronic Stability Control),
System P. 352
2 VSA® On and Off P. 353
—
● Goes off when all doors, glass hatch, and
tailgate are closed.
● Goes off when all doors, glass hatch, and
tailgate are closed.
—
* Not available on all models
QRG
TOC
Index
Home
72
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
Daytime Running Lights Indicator *
System Message Indicator *
● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● Comes on if there is a problem with
the DRL system.
● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● Comes on along with a beep when a
problem is detected. A system message on the multi-information display appears at the same time.
● Have your vehicle checked by a dealer.
2 Daytime Running Lights P. 127
● While the indicator is on, press the (information) button to see the
message again.
● Refer to the Indicators information in this chapter when a system message appears on the multi-information display. Take the appropriate action for the message. ● The multi-information display does not return
—
to the normal screen unless the warning is canceled, or the button is pressed.
(information)
QRG
TOC
A/T Temperature Indicator
● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● Comes on when the transmission
fluid temperature is too high.
● Comes on while driving - Stop in a safe place, shift to (P, and idle the engine until the indicator goes off.
* Not available on all models
Index
Home
Continued
73
QRG
TOC
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
Models with information display TPMS Indicator
Models with information display Low Tire Pressure Indicator
Models with multi- information display Low Tire Pressure/TPMS Indicator
● Comes on for a few seconds when you turn the ignition switch to ON (w.
● Comes on if there is a problem with the TPMS, or when a compact spare tire is temporarily installed.
● Stays on constantly or does not come on at all - Have the vehicle checked by a dealer. If the vehicle is fitted with a compact spare, get your regular tire repaired or replaced and put back on your vehicle as soon as you can.
● Comes on for a few seconds when you turn the ignition switch to ON (w.
● Comes on if the tire pressure of any of the tires becomes significantly low.
Models with information display ● Comes on for a while and then goes
off when a compact spare tire is temporarily installed.
● Comes on while driving - Stop in a safe
place, check tire pressures, and inflate the tire(s) if necessary.
Models with multi-information display ● Blinks and remains on - Have the
vehicle checked by a dealer. If the vehicle is fitted with a compact spare, get your regular tire repaired or replaced and put back on your vehicle as soon as you can.
—
Models with multi-information display ● Blinks for about one minute, and then stays on if there is a problem with the TPMS, or when a compact spare tire is temporarily installed.
Index
Home
74
* Not available on all models
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
Turn Signal Indicators
● The turn signal indicators blink when
● Does not blink or blinks rapidly - A
you operate the turn signal lever. ● If you press the hazard warning
button, both indicators and all turn signals blink at the same time.
turn signal light bulb has blown. Change the bulb immediately.
2 Replacing Light Bulbs P. 404 P. 405
P. 406
High Beam Indicator
● Comes on when the high beam
headlights are on.
—
Lights On Indicator
Fog Light Indicator *
● Comes on whenever the light switch is on, or in AUTO when the exterior lights are on.
● If you remove the key from the ignition switch while the lights are on, a chime sounds when the driver's door is opened.
● Comes on when the fog lights are on.
—
—
—
—
—
U.S.
Side Airbag Off Indicator
Canada
● Comes on for a few seconds when you turn the ignition switch to ON (w, then goes off.
● Comes on when the passenger side airbag system is automatically shut off.
● It does not mean there is a problem with
your side airbags.
● Comes on when nobody is sitting in the passenger seat - Have the vehicle checked by a dealer.
● Comes on when someone is sitting in
the seat - Have the passenger sit properly.
QRG
TOC
* Not available on all models
Index
Home
Continued
75
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
● Comes on briefly when you turn the ignition switch to ON (w, then goes off.
● Comes on if the immobilizer system
Immobilizer System Indicator
cannot recognize the key information.
● Blinks - You cannot start the engine.
Turn the ignition switch to LOCK (0, pull the key out, and then insert the key and turn it to ON (w again.
● Repeatedly blinks - The system may be malfunctioning. Have the vehicle checked by a dealer.
● Do not attempt to alter this system or add
other devices to it. Electrical problems can occur.
Security System Alarm Indicator *
● Blinks when the security system alarm
has been set.
2 Security System Alarm* P. 118
● Comes on if there is a problem with
● As a temporary measure, hold the
U.S.
the starter system.
Canada
Starter System Indicator *
ignition switch to START (e for up to 15 seconds and start the engine. Have the vehicle checked by a dealer.
—
—
U.S.
Canada
Fuel Economy Indicator
● Comes on and stays on while you are
driving with good fuel economy.
—
—
* Not available on all models
QRG
TOC
Index
Home
76
uuIndicatorsu
Indicator
Name
On/Blinking
Explanation
Message *
CRUISE MAIN Indicator
● Comes on when you press the
CRUISE button.
2 Cruise Control P. 348
CRUISE CONTROL Indicator
Washer Level Indicator *
Maintenance Minder Indicator *
U.S.
Canada
Power Tailgate Indicator *
● Comes on if you have set a speed for
cruise control.
2 Cruise Control P. 348
● Comes on when washer fluid is low.
● Refill washer fluid.
2 Refilling Window Washer Fluid
P. 401
● Comes on when you turn the ignition
switch to ON (w, then goes off. ● Comes on when the scheduled
maintenance is due soon.
2 Maintenance Minder™ P. 381
● Comes on for a few seconds when you turn the ignition switch to ON (w.
● Comes on if there is a problem with
● Stays on constantly or does not come on at all - You can still open or close the tailgate manually. Have the vehicle checked by a dealer.
the power tailgate system.
—
—
—
U.S.
Canada
QRG
TOC
* Not available on all models
Index
Home
77
QRG
TOC
uuIndicatorsuMulti-Information Display Warning and Information Messages*
Multi-Information Display Warning and Information Messages* The following messages appear only on the multi-information display. Press the with the system message indicator on.
(information) button to see the message again
Message
Condition
Explanation
● Appears when the fuel fill cap is loose or is not
installed.
2 Check/Tighten Fuel Cap Message P. 451
● Appears when the scheduled maintenance is due
soon.
2 Maintenance Minder Messages on the Multi-
● Consequently, SERVICE DUE NOW and SERVICE
Information Display P. 386
PAST DUE follow.
● Appears when you open the driver's door while the
● Remove the key from the ignition switch.
ignition key is in LOCK (0.
● Appears when the engine coolant temperature gets
abnormally high.
2 Overheating P. 448
● Appears when the daytime running lights are off.
2 Daytime Running Lights P. 127
Index
Home
78
* Not available on all models
uuIndicatorsuMulti-Information Display Warning and Information Messages*
Message
Condition
Explanation
● Appears if there is a problem with the parking sensor
● Check if the area around the sensor(s) is covered with
system. The beeper sounds.
mud, ice, snow, etc. If the indicator(s) stays on even after you clean the area, have the system checked by a dealer.
TOC
QRG
* Not available on all models
Index
Home
79
Gauges and Displays
QRG
Gauges Gauges include the speedometer, tachometer, fuel gauge, and related indicators. They are displayed when the ignition switch is in ON (w.
TOC
■ Speedometer Displays your driving speed in mph (U.S.) or km/h (Canada).
■ Tachometer Shows the number of engine revolutions per minute.
■ Fuel Gauge Displays the amount of fuel left in the fuel tank.
■ Temperature Gauge Displays the temperature of the engine coolant.
1Fuel Gauge
NOTICE You should refuel when the reading approaches Running out of fuel can cause the engine to misfire, damaging the catalytic converter.
The actual amount of remaining fuel may differ from the fuel gauge reading.
1Temperature Gauge
NOTICE Driving with the temperature gauge pointer in the upper zone can cause serious engine damage. Pull safely to the side of the road and allow engine temperature to return to normal.
2 Overheating P. 448
Index
Home
80
Information Display* The information display shows the odometer, trip meter, engine oil life and maintenance service item codes, and other gauges.
■ Switching the Display Press the
(Select/Reset) knob to change the display.
uuGauges and DisplaysuInformation Display*
QRG
TOC
Odometer
Range (estimated distance)
Outside temperature *
Trip meter B
Trip meter A
Engine oil life
Instant fuel economy
Average fuel economy
■ Odometer Shows the total number of miles or kilometers that your vehicle has accumulated.
* Not available on all models
Continued
Index
Home
81
QRG
TOC
uuGauges and DisplaysuInformation Display*
■ Trip Meter Shows the total number of miles or kilometers driven since the last reset. Meters A and B can be used to measure two separate trips.
1Trip Meter
Switch between trip meter A and trip meter B by pressing the
knob.
■ Resetting a trip meter To reset a trip meter, display it, then press and hold the reset to 0.0.
knob. The trip meter is
■ Instant Fuel Economy Shows the instant fuel economy as a bar graph in mpg or l/100 km.
■ Average Fuel Economy Shows the estimated average fuel economy of each trip meter in mpg (U.S.) or l/100 km (Canada). The display is updated at set intervals. When a trip meter is reset, the average fuel economy is also reset.
■ Engine Oil Life Shows the remaining oil life and Maintenance MinderTM.
2 Maintenance Minder™ P. 381
■ Range Shows the estimated distance you can travel on the remaining fuel. This distance is estimated from the fuel economy of your trips in the past.
* Not available on all models
Index
Home
82
■ Check Fuel Cap Appears when the fuel fill cap is loose or is not installed.
2 Check/Tighten Fuel Cap Message P. 451
■ Tire Pressure Monitor Shows each tire’s pressure.
2 TPMS (Tire Pressure Monitoring System) P. 355
uuGauges and DisplaysuInformation Display*
QRG
TOC
* Not available on all models
Continued
Index
Home
83
QRG
TOC
1Outside Temperature*
The temperature sensor is in the front bumper. Road heat and exhaust from another vehicle can affect the temperature reading when your vehicle speed is less than 19 mph (30 km/h).
It may take several minutes for the display to be updated after the temperature reading has stabilized.
1Adjusting the outside temperature indicator
Adjust the temperature reading up to ±5ºF or ±3ºC.
uuGauges and DisplaysuInformation Display*
■ Outside Temperature* Shows the outside temperature in Fahrenheit (U.S.) or Celsius (Canada).
■ Adjusting the outside temperature indicator Adjust the temperature reading up to ±5ºF or ±3ºC if the temperature reading seems incorrect. Reset Mode Initial Display
1. Turn the ignition switch to ON (w.
Oil life
Outside Temperature
2. Press and hold the
(Select/Reset) knob
for 10 seconds or more. u The information display shows the reset
mode initial display.
3. Select outside temperature with the
knob.
4. Press and hold the
knob for a few
seconds to enter the outside temperature setting mode.
5. Turn the
knob to adjust the
temperature.
6. Press and release the
knob.
u The new outside temperature is now
entered.
Index
Home
84
* Not available on all models
uuGauges and DisplaysuMulti-Information Display*
Multi-Information Display* Shows the odometer, trip meter, outside temperature indicator, and other gauges. It also displays important messages such as warnings and other helpful information.
■ Switching the Display
Press the
(information) button or the SEL/RESET button to change the display.
QRG
TOC
Odometer
Trip Computer
Button
Trip meter A
Tire Pressure Monitor
SEL/RESET Button
Engine oil life
Trip meter B
Customize Settings
* Not available on all models
Index
Home
Continued
85
uuGauges and DisplaysuMulti-Information Display*
QRG
TOC
Trip Computer
Instant fuel economy
Average fuel economy
Button
SEL/RESET Button
Average Speed
Elapsed Time
Range
■ Odometer Shows the total number of miles or kilometers that your vehicle has accumulated.
Index
Home
86
* Not available on all models
uuGauges and DisplaysuMulti-Information Display*
■ Trip Meter Shows the total number of miles or kilometers driven since the last reset. Meters A and B can be used to measure two separate trips.
1Trip Meter
Switch between trip meter A and trip meter B by pressing the SEL/RESET button.
■ Resetting a trip meter To reset a trip meter, display it, then press and hold the SEL/RESET button. The trip meter is reset to 0.0.
■ Outside Temperature Shows the outside temperature in Fahrenheit (U.S.) or Celsius (Canada).
■ Adjusting the outside temperature display Adjust the temperature reading up to ±5°F or ±3°C if the temperature reading seems incorrect.
1Outside Temperature
The temperature sensor is in the front bumper. Road heat and exhaust from another vehicle can affect the temperature reading when your vehicle speed is less than 19 mph (30 km/h).
It may take several minutes for the display to be updated after the temperature reading has stabilized.
Use the multi-information display’s customized features to correct the temperature.
2 Customized Features P. 90
QRG
TOC
* Not available on all models
Continued
Index
Home
87
QRG
TOC
uuGauges and DisplaysuMulti-Information Display*
■ Trip Computer Shows the instant fuel economy, average fuel economy, range, elapsed time, and average speed.
■ Instant Fuel Economy Shows the instant fuel economy as a bar graph in mpg (U.S.) or l/100 km (Canada).
■ Average Fuel Economy Shows the estimated average fuel economy of each trip meter in mpg (U.S.) or l/100 km (Canada). The display is updated at set intervals. When a trip meter is reset, the average fuel economy is also reset.
1Average Fuel Economy
You can change when to reset the average fuel economy.
2 Customized Features P. 90
■ Range Shows the estimated distance you can travel on the remaining fuel. This distance is estimated from the fuel economy of your trips in the past.
■ Elapsed Time Shows the time elapsed since the last time Trip A or Trip B was reset.
■ Average Speed Shows the average speed in mph or km/h since the last time Trip A or Trip B was reset.
1Elapsed Time
You can change when to reset the elapsed time.
2 Customized Features P. 90
1Average Speed
You can change when to reset the average speed.
2 Customized Features P. 90
■ Tire Pressure Monitor Shows each tire's pressure.
2 TPMS (Tire Pressure Monitoring System) P. 355
* Not available on all models
Index
Home
88
■ Engine Oil Life Shows the remaining oil life and Maintenance MinderTM.
2 Maintenance Minder™ P. 381
uuGauges and DisplaysuMulti-Information Display*
QRG
TOC
* Not available on all models
Continued
Index
Home
89
QRG
TOC
uuGauges and DisplaysuMulti-Information Display*
■ Customized Features Use the multi-information display to customize certain features.
■ How to customize Select the CUSTOMIZE SETTINGS by pressing the button while the ignition switch is in ON (w, and the vehicle is at a complete stop. Press the SEL/ RESET button to change the display to the CHG SETTING.
1Customized Features
To customize other features, press the button.
2 List of customizable options P. 92
2 Example of customization settings P. 94
Customization is possible when you see the driver’s ID (DRIVER 1 or DRIVER 2) on the CHG SETTING screen. The driver’s ID indicates which remote transmitter you have used to unlock the driver’s door. The customized settings are recalled every time you unlock the driver’s door with that remote.
When you customize settings: Shift to (P.
Button
Changes the customize menu and items.
SEL/RESET Button Enters the selected item.
Index
Home
90
* Not available on all models
uuGauges and DisplaysuMulti-Information Display*
QRG
■ Customization flow Press the
button.
CUSTOMIZE SETTINGS
SEL/RESET
LANGUAGE SELECTION
TOC
CHG SETTING
SEL/RESET
METER SETUP
SEL/RESET
ADJUST OUTSIDE TEMP. DISPLAY
SEL/RESET
DEFAULT ALL
EXIT
TRIP A INFO RESET
POSITION SETUP
SEL/RESET
MEMORY POSITION LINK
LIGHTING SETUP
SEL/RESET
SEL/RESET
DOOR/WINDOW SETUP
SEL/RESET
EXIT
INTERIOR LIGHT DIMMING TIME HEADLIGHT AUTO OFF TIMER
AUTO LIGHT SENSITIVITY
AUTO DOOR LOCK
AUTO DOOR UNLOCK
KEY AND REMOTE UNLOCK MODE KEYLESS LOCK ACKNOWLEDGMENT
SECURITY RELOCK TIMER PTG KEYLESS OPEN MODE *
* Not available on all models
Index
Home
Continued
91
QRG
TOC
uuGauges and DisplaysuMulti-Information Display*
■ List of customizable options
Setup Group
Customizable Features
Description
Selectable Settings
LANGUAGE SELECTION
Changes the displayed language.
ENGLISH*/FRENCH/SPANISH
ADJUST OUTSIDE TEMP. DISPLAY
Adjusts the temperature reading by a few degrees.
-5°F ~ ±0°F* ~ +5°F (U.S.)
-3°C ~ ±0°C* ~ +3°C (Canada)
TRIP A INFO RESET
Changes the setting of how to reset trip meter A, average fuel economy A, average speed A, and elapsed time A.
with REFUEL/ MANUAL ONLY*/IGN OFF
MEMORY POSITION LINK
Changes the driver's seat and the outside mirror positions to a stored setting.
ON*/OFF
INTERIOR LIGHT DIMMING TIME
Changes the length of time the interior lights stay on after you close the doors.
60 sec/30 sec*/15 sec
HEADLIGHT AUTO OFF TIMER
Changes the length of time the exterior lights stay on after you close the driver's door.
60 sec/30 sec/15 sec*/0 sec
AUTO LIGHT SENSITIVITY Changes the timing for the headlights to come on.
MAX/HIGH/MID*/LOW/MIN
METER SETUP
POSITION SETUP
LIGHTING SETUP
*: Default Setting
Index
Home
92
* Not available on all models
Setup Group
Customizable Features
Description
Selectable Settings
AUTO DOOR LOCK
Changes the setting for the automatic locking feature.
SHIFT FROM (P/WITH VEH SPEED*2/OFF
uuGauges and DisplaysuMulti-Information Display*
QRG
AUTO DOOR UNLOCK
Changes the setting for when the doors unlock automatically.
SHIFT TO (P *2/IGN OFF/OFF
TOC
DRIVER DOOR*2/ALL DOORS
DOOR/ WINDOW SETUP
KEY AND REMOTE UNLOCK MODE
Sets up either the driver's door or all doors to unlock on the first push of the remote transmitter.
DRIVER DOOR*2/ALL DOOR
KEYLESS LOCK ACKNOWLEDGMENT
LOCK/UNLOCK- The exterior lights flash. LOCK (2nd push)- The beeper sounds.
ON*2/OFF
SECURITY RELOCK TIMER
Changes the time it takes for the doors to relock and the security system to set after you unlock the vehicle without opening any door.
90 sec/60 sec/30 sec*2
PTG KEYLESS OPEN
MODE*1
Changes the keyless setting for when the power tailgate opens.
ANYTIME*2 / WHEN UNLOCKED
DEFAULT ALL
*1:Not available on all models *2: Default Setting
* Not available on all models
Cancels/Resets all the customized settings as default.
CANCEL*2/SET
Index
Home
Continued
93
QRG
TOC
uuGauges and DisplaysuMulti-Information Display*
■ Example of customization settings The steps for changing the TRIP A INFO RESET setting to with REFUEL are shown below. The default setting for TRIP A INFO RESET is MANUAL ONLY.
1. Press and release
button until CUSTOMIZE SETTINGS appears on the display.
2. Press the SEL/RESET button.