2010 Ford Mustang Owners Manual

fuses and relays.

215

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

The fuses are coded as follows: Fuse Amp

Fuse/Relay Location

Rating

30A 15A 15A 30A

10A

20A 10A 10A 15A 15A

Protected Circuits

Driver rear window (convertible only) Brake On/Off (BOO) power SYNC威 Passenger rear window (convertible only) Brake transmission shift interlock (BTSI) Turn signals, Hazard flashers Left low beam headlamp Right low beam headlamp Courtesy lamps Switch illumination

10

216

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

Fuse/Relay Location

Fuse Amp

Rating

Protected Circuits

11
12
13
14

15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34

35

36
37
38

10A 7.5A 5A 10A

10A 15A 20A 20A 25A 15A 15A 15A 15A 20A 10A 10A 20A 5A 5A 5A 10A 10A 10A 5A

10A

5A 10A 20A

Security module Power mirrors Not used (Spare) Center information display, Electronic finish panel, GPS Climate control Not used (Spare) Power door locks Not used (Spare) Navigation amp Diagnostic connector Fog lamps Park lamps, License lamps High beam headlamps Horn Demand lighting (battery saver) Cluster (battery) Ignition switch feed Audio mute (Start) Camera (Run/Start) Not used (Spare) Restraints control module (RCM) Not used (Spare) Not used (Spare) Electronic stability control, Steering angle Auxiliary body module (ABM) Run/Start Passive anti-theft system (PATS) Not used (Spare) Not used (Spare)

217

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

Fuse/Relay Location

Fuse Amp

Rating

Protected Circuits

39
40
41

42
43
44
45
46

47

48

20A 20A 15A

10A 10A 10A 5A 7.5A

30A Circuit

Breaker

—

Radio/Navigation Not used (Spare) Accessory delay (windows, automatic dimming rear view mirror [including microphone and compass] and door switch III) Not used (Spare) Heated seat relay coils Not used (Spare) Wiper relay and module, Blower relay Passenger airbag deactivation indicator (PADI), Occupant classification sensor (OCS) Not used (Spare)

Accessory delay relay (windows, automatic dimming rear view mirror [including microphone and compass] and door switch III)

Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Do not probe the contacts for the fuses and relays in the power distribution box as damage will occur, causing improper, or loss of, electrical functionality.

WARNING: Always disconnect the battery before servicing high current fuses.

WARNING: To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the

battery or refilling fluid reservoirs.

218

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter.

The high-current fuses are coded as follows.

Fuse/Relay Location

10
11
12
13

Fuse Amp

Rating 80A*

— —

30A* 20A* 40A* 40A* 40A*

30A* 30A*

— —

15A**

Protected Circuits

Passenger compartment fuse panel Not used Not used Blower motor relay Powerpoint (body) Rear defroster Cooling fan relay Anti-lock brake system (ABS) pump Wipers ABS valve Not used Not used Fuel pump relay

219

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

Fuse/Relay Location

14
15

16
17
18
19
20

21
22
23

24
25
26

27

28
29
30
31
32
33

34
35
36
37
38
39

Fuse Amp

Protected Circuits

Rating 15A** 10A**

20A** 10A** 20A* 30A* 30A*

30A* 20A* 10A**

—

10A** 20A**

20A**

—

30A*

—

30A* 30A* 30A*

30A* 40A* Diode

— — 5A**

Fuel pump relay #2 (Shelby only) Intercooler pump relay (Shelby only) Heated seats Alternator sense Auxiliary body module (ABM) Starter relay Rear amplifier (Shaker 1000 radio) Powertrain relay Powerpoint (instrument panel) Powertrain control module (PCM) keep-alive power Not used A/C compressor relay Left high intensity discharge headlamp relay Right high intensity discharge headlamp relay Not used Passenger front window Not used Passenger power seat Driver power seat Front amplifier (Shaker 500 radio) Driver front window motor Convertible top motor Fuel diode Not used Not used Rear defroster coil (Run/Start)

220

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Fuse/Relay Location

40

41
42

43
44
45
46

47
48

49

50
51
52
53
54
55
56

57
58

Roadside Emergencies

Protected Circuits

PCM Vehicle Power 4 – ignition coil Fuel pump relay Intercooler pump relay (Shelby only) A/C compressor relay Fuel pump relay #2 (Shelby only) PCM Run/Start PCM Vehicle Power 3 – general powertrain components PCM Vehicle Power 1
PCM Vehicle Power 5 – transmission PCM Vehicle Power 2 – emissions related powertrain components Cooling fan relay (high) Blower motor relay Starter relay Rear defroster relay Front wiper relay Cooling fan relay (low) Not used (Spare)

Fuse Amp

Rating 15A**

G8VA relay G8VA relay

G8VA relay G8VA relay

5A** 5A**

15A** 15A**

15A**

Full ISO relay Full ISO relay Full ISO relay Full ISO relay Full ISO relay Full ISO relay High current

relay

Full ISO relay High current

PCM relay Not used (Spare)

relay

* Cartridge Fuses ** Mini Fuses

Auxiliary relay with heated seats (if equipped) On heated seat equipped vehicles, there is a relay box located under the driver seat containing two relays for the driver and passenger heated seats.

221

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare tire is in use. To restore the full functionality of the monitoring system, all road wheels equipped with tire pressure monitoring sensors must be mounted on the vehicle. Have a flat serviced by an authorized dealer in order to prevent damage to the TPMS sensors, refer to Tire pressure monitoring system (TPMS) in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. During repairing or replacing of the flat tire, have the authorized dealer inspect the TPMS sensor for damage.

WARNING: The use of tire sealants may damage your Tire Pressure Monitoring System and should only be used if it is

supplied with your vehicle as part of the original temporary mobility kit.

WARNING: Refer to Tire pressure monitoring system (TPMS) in the Tires, Wheels and Loading chapter for important

information. If the tire pressure monitor sensor becomes damaged, it will no longer function.

Dissimilar spare tire/wheel information

WARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.

If you have a dissimilar spare tire/wheel, then it is intended for temporary use only. This means that if you need to use it, you should replace it as soon as possible with a road tire/wheel that is the same size and type as the road tires and wheels that were originally provided by Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired.

222

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

tire

Safety Compliance Label

A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter “T” for tire size and may have “Temporary Use Only” molded in the sidewall 2. Full-size dissimilar spare with label on wheel: This spare tire has a label on the wheel that states: “THIS TIRE AND WHEEL FOR TEMPORARY USE ONLY” When driving with one of the dissimilar spare tires listed above, do not: • Exceed 50 mph (80 km/h) • Load the vehicle beyond maximum vehicle load rating listed on the • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar spare • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar spare

tire/wheel

223

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible. Stopping and securing the vehicle

1. Park on a level surface, set the parking brake and activate the hazard flashers. 2. Place the gearshift lever in P (Park) (automatic transmission) or R (Reverse) (manual transmission) and turn the engine off.

Tire change procedure

WARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or

slipping off the jack, even if the vehicle is in P (Park) (automatic transmission) or R (Reverse) (manual transmission).

WARNING: To help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in

both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.

224

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

WARNING: If the vehicle slips off the jack, you or someone else could be seriously injured.

WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to

avoid the danger of being hit when operating the jack or changing the wheel.

Note: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Block both the front and rear of the wheel diagonally opposite the flat tire. For example, if the left front tire is flat, block the right rear wheel.

2. Remove the lug wrench, spare tire and jack.

225

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

3. Remove the center ornament (if equipped) from the wheel. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground.

4. Put the jack in the jack notch next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground.

Never use the rear differential as a jacking point.

WARNING: To lessen the risk of personal injury, do

not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.

5. Remove the lug nuts with the lug wrench. 6. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. If you are using the temporary tire, the lug nut washers will not appear to be flush with the rim. This is normal only when using the temporary spare tire. 226

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

7. Lower the wheel by turning the jack handle counterclockwise. 8. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 9. Put flat tire, wheel ornament (if equipped), jack and lug wrench away. Make sure the jack is fastened so it does not rattle when you drive. 10. Unblock the wheel.

TEMPORARY MOBILITY KIT (IF EQUIPPED) Your vehicle may be equipped with a temporary mobility kit (located in the spare tire well in the trunk). The temporary mobility kit consists of an air compressor to reinflate the tire and a sealing compound in a canister that will effectively seal most punctures caused by nails or similar objects. This kit will provide a temporary seal allowing you to drive your vehicle up to 120 miles (200 km) at a maximum speed of 50 mph (80 km/h). Note: The temporary mobility kit sealant compound in the canister is to be used for one tire only. See your Ford authorized dealer for additional replacement sealant canisters.

227

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

1. Air compressor (inside) 2. Diverter knob 3. On/Off button 4. Air pressure gauge 5. Sealant bottle/canister 6. Sealant filling clear tube 7. Sealant tube — tire valve connector 8. Yellow cap tool 9. Air compressor hose 10. Air hose — tire valve connector 11. Accessory power plug 12. Casing/housing

12

11

10

General information

WARNING: Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.

Do not attempt to repair punctures larger than 1⁄4 inch (6.4 mm) or damage to the tire’s sidewall. The tire may not completely seal. Note: Do not use the temporary mobility kit if a tire has become severely damaged by driving the vehicle with a tire that has insufficient air pressure. Only punctured areas located within the tire tread can be sealed with the temporary mobility kit. Loss of air pressure may adversely affect tire performance. For this reason: • Do not drive the vehicle above 50 mph (80 km/h). • Do not drive further than 120 miles (200 km). Drive only to the

closest Ford Motor Company authorized dealer or tire repair shop to have your tire inspected.

• Drive carefully and avoid abrupt steering maneuvers. • Periodically monitor tire inflation pressure in the affected tire; if the

tire is losing pressure, have the vehicle towed.

228

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies • Read the information in the Tips for use of the temporary mobility kit section to ensure safe operation of the temporary mobility kit and your vehicle.

Tips for use of the temporary mobility kit Read the following list of tips to ensure safe operation of the temporary mobility kit: • Before operating the temporary mobility kit, make sure your vehicle is safely off the road and away from moving traffic. Turn on the hazard lights.

• Always set the parking brake to ensure the vehicle doesn’t move • Do not remove any foreign objects, such as nails or screws, from the • When using the temporary mobility kit, leave the engine running

unexpectedly.

tire.

operating.

(only if the vehicle is outdoors or in a well-ventilated area) so the compressor doesn’t drain the vehicle’s battery. • Do not allow the compressor to operate continuously for more than 15 minutes; this will help prevent the compressor from overheating. • Never leave the temporary mobility kit unattended when it is • Sealant compound contains latex. Make sure that you use the non-latex gloves provided to avoid an allergic reaction. • Keep the temporary mobility kit away from children. • Only use the temporary mobility kit when the ambient temperature is • Only use the sealing compound before the use by date. The use by date is on the lower right hand corner of the label located on the sealant canister (bottle). Check the use by date regularly and replace the canister after four years.

between -22°F (–30°C) and 158°F (70°C).

• Do not store the temporary mobility kit unsecured inside the

passenger compartment of the vehicle as it may cause injury during a sudden stop or collision. Always store the kit in its original location. • After sealant use, the TPMS sensor and valve stem on the wheel must • When inflating a tire or other objects, use the black air hose only. Do not use the transparent hose which is designed for sealant application only.

be replaced by an authorized Ford dealer.

229

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies • Operating the temporary mobility kit could cause an electrical

disturbance in radio and DVD player operation.

What to do when a tire is punctured A tire puncture within the tire’s tread area can be repaired in two stages with the temporary mobility kit: • In the first stage, the tire will be reinflated with a sealing compound and air. After the tire has been reinflated, you will need to drive the vehicle a short distance (approximately 4 miles [6 km]) to distribute the sealant in the tire.

• In the second stage, you will need to check the tire pressure and

adjust, if necessary, to the vehicle’s tire inflation pressure.

First stage: Reinflating the tire with sealing compound and air Preparation Park the vehicle in a safe, level and secure area, away from moving traffic. Turn the hazard lights on. Apply the parking brake and turn the engine off. Inspect the flat tire for visible damage. Sealant compound contains latex. To avoid any allergic reactions, use the non-latex gloves located in the accessory box on the underside of the temporary mobility kit housing. Do not remove any foreign object that has pierced the tire. If a puncture is located in the tire sidewall, stop and call roadside assistance. 1. Remove the valve cap from the tire valve. 2. Unwrap the clear tube from the compressor housing. 3. Remove the tube cap and fasten the metal connector of the tube to the tire valve, turning clockwise. Make sure the connection is tightly fastened.

230

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

4. Plug the power cable into the 12V power point in the vehicle.

5. Remove the warning sticker found on the canister and place it on the top of the instrument panel or the center of the dash. 6. Start the engine (only if the vehicle is outdoors or in a well-ventilated area). 7. Turn dial (1) counterclockwise to the sealant position. Turn on the kit by pressing the on/off button (2).

8. Inflate the tire to the pressure listed on the tire label located on the driver’s door or the door jam area.

Note: When the sealing compound is first added into the tire, the air pressure gauge reading on the compressor unit may indicate a higher value; this is normal and should be no reason for concern. The pressure will drop after about 30 seconds of operation. The

231

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

tire pressure has to be checked with the compressor in the OFF position to get the correct tire pressure reading.

WARNING: Do not stand directly over the temporary mobility kit while inflating the tire. If you notice any unusual bulges or

deformations in the tire’s sidewall during inflation, stop and call roadside assistance.

WARNING: If the tire doesn’t inflate to the recommended tire pressure within 15 minutes, stop and call roadside assistance.

9. When the recommended tire pressure is reached, turn off the kit by pressing the on/off button; disconnect the kit from the tire valve and the power point. Re-install the valve cap on the tire valve, place the tube cap on the metal connector, and return the kit to the stowage area. 10. Immediately and cautiously, drive the vehicle 4 miles (6 km) to distribute the sealant evenly inside the tire. Do not exceed 50 mph (80 km/h).

Note: If you experience any unusual vibration, ride disturbance or noise while driving, reduce your speed until you can safely pull off to the side of the road to call for roadside assistance. Do not proceed to the second stage of this operation.

11. After 4 miles (6 km), stop and check the tire pressure. See Second stage: Checking tire pressure.

Second stage: Checking tire pressure Check the air pressure of your tires as follows: 1. Remove the valve cap from the tire valve. 2. Unhook the black hose from the side of the compressor and fasten firmly on the valve stem by turning clockwise.

WARNING: If you are proceeding from the First stage: Reinflating the tire with sealing compound and air section and have injected sealant in the tire and the pressure is below 20 psi (1.4 bar), stop and call roadside assistance. If tire pressure is above 20 psi (1.4 bar), continue to the next step.

3. Turn the dial clockwise to the air position. Turn on the kit by pressing the on/off button. 232

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

4. Adjust the tire to the recommended inflation pressure from the tire label located on the driver’s door or door jam area. Note: The tire pressure has to be checked with the compressor in the OFF position to get the correct tire pressure reading. 5. Turn the compressor off by pressing the on/off button. 6. Unplug the hoses, re-install the valve cap on the tire and return the kit to the stowage area.

WARNING: The power plug may get hot after use and should be handled carefully while unplugging.

What to do after the tire has been sealed After using the temporary mobility kit to seal your tire, you will need to replace the sealant canister and clear tube (hose). Sealing compound and spare parts can be obtained and replaced at an authorized Ford Motor Company dealership or tire dealer. Empty sealant bottles may be disposed of at home; however, liquid residue from the sealing compound should be disposed by your local Ford Motor Company dealership or tire dealer, or in accordance with local waste disposal regulations. Note: After the sealing compound has been used, the maximum vehicle speed is 50 mph (80 km/h) and the maximum driving distance is 120 miles (200 km). The sealed tire should be inspected immediately. Note: After sealant use, the TPMS sensor and valve stem on the wheel must be replaced by an authorized Ford dealer. You can check the tire pressure any time within the 120 miles (200 km) by performing the procedure from Second stage: Checking tire pressure listed previously.

233

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

Removal of the sealant canister from the temporary mobility kit 1. Unwrap the clear tube from the compressor housing.

2. Locate the yellow cap at the end of the clear tube.

3. Using the yellow cap tool, press the tab located on the temporary mobility kit compressor housing while pulling up on the sealant canister.

234

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

Installation of the sealant canister to the temporary mobility kit 1. Align the sealant canister with the temporary mobility kit housing.

2. Once aligned, seat the sealant canister by lightly pushing down until you hear an audible click.

3. Wrap the clear tube around the compressor housing.

Note: If you experience any difficulties with the removal or installation of the sealant canister, consult your Ford Motor Company authorized dealer for assistance.

235

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

Be sure to check the sealant compound’s “use by” date regularly. The “use by” date is on the lower right hand corner of the label located on the sealant canister (bottle). The sealant canister should be replaced after four years.

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.).

Bolt size

Wheel lug nut torque*

1⁄2 x 20
* Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners.

ft-lb 100

N•m 135

WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting

surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Ensure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel. Installing wheels without correct metal-to-metal contact at the wheel mounting surfaces can cause the wheel nuts to loosen and the wheel to come off while the vehicle is in motion, resulting in loss of control.

Note: Inspect the wheel pilot hole prior to installation. If there is visible corrosion in wheel pilot hole, remove loose particles by wiping with clean rag and apply grease. Apply grease only to the wheel pilot hole surface by smearing a “dime” (1 square cm) sized glob of grease around the wheel pilot surface (1) with end of finger. DO NOT apply grease to lugnut/stud holes or wheel-to-brake surfaces.

236

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

RUNNING OUT OF FUEL If you have run out of fuel and need to refill the vehicle with a portable fuel container, see Running out of fuel in the Maintenance and Specifications chapter for proper fuel filling method using a portable fuel container and the included fuel filler funnel. Do not insert the nozzle of portable fuel containers or any type of aftermarket funnels into the Easy Fuel™ “no cap” fuel system as it can be damaged. You must use the included funnel in such circumstances.

WARNING: Do not insert the nozzle of portable fuel containers or aftermarket funnels into the Easy Fuel™ system. This could damage the fuel system and its seal, and may cause fuel to run onto the ground instead of filling the tank, all of which could result in serious personal injury.

JUMP STARTING

WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could

result in injury or vehicle damage.

WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.

Do not attempt to push-start your automatic transmission vehicle. Automatic transmissions do not have push-start capability. Attempting to push-start a vehicle with an automatic transmission may cause transmission damage.

Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system.

237

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect from any electrical surges. Turn all other accessories off.

Connecting the jumper cables

+–

+–

1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.

+–

+–

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 238

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

+–

+–

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.

+–

+–

4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points.

WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may

cause an explosion of the gases that surround the battery.

5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed.

239

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.

Removing the jumper cables

+–

+–

Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery.

+–

+–

2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.

240

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

+–

+–

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.

+–

+–

4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.

241

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

WRECKER TOWING

If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If your vehicle is to be towed from the front using wheel lift equipment, it is recommended that the rear wheels (drive wheels) be placed on a dolly to prevent damage to the transmission. If your vehicle is to be towed from the rear using wheel lift equipment, it is recommended that the front wheels be placed on a dolly to prevent damage to the front fascia. If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle. 242

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Roadside Emergencies

Emergency towing In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer, or flatbed transport vehicle) your vehicle (regardless of transmission powertrain configuration) can be flat towed (all wheels on the ground) under the following conditions: • Vehicle is facing forward so that it is being towed in a forward • Place the transmission in N (Neutral). Refer to Brake-shift interlock in the Driving chapter for specific instructions if you cannot move the gear shift lever into N (Neutral).

direction.

• Maximum speed is not to exceed 35 mph (56 km/h). • Maximum distance is 50 miles (80 km).

243

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Customer Assistance

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized Ford, Lincoln, or Mercury dealer. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs. This means that, depending on the warranty repair needed, you may have to take your vehicle to another authorized dealer. A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft威 parts, or remanufactured or other parts that are authorized by Ford.

Away from home If you are away from home when your vehicle needs service, contact the Ford Customer Relationship Center or use the online resources listed below to find the nearest authorized dealer. In the United States: Mailing address Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
Telephone 1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) Online Additional information and resources are available online at www.genuineservice.com. • U.S. dealer locator by Dealer Name, City/State, or Zip Code • Owner Guides • Maintenance Schedules • Recalls • Ford Extended Service Plans • Ford Genuine Accessories • Service specials and promotions. 244

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Customer Assistance

In Canada: Mailing address (Ford vehicles) Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
Telephone 1-800-387-9333
Online www.lincolncanada.com Additional assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing authorized dealer. 2. If your inquiry or concern remains unresolved, contact the Sales Manager, Service Manager or Customer Relations Manager. 3. If you require assistance or clarification on Ford Motor Company policies, please contact the Ford Customer Relationship Center In order to help you serve you better, please have the following information available when contacting a Customer Relationship Center: • Vehicle Identification Number (VIN) • Your telephone number (home and business) • The name of the authorized dealer and city where located • The vehicle’s current odometer reading In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states.

245

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Customer Assistance

In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws.

IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle. California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18 months of ownership of a new vehicle or the first 18,000 miles (29,000 km), whichever occurs first: 1. Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time) In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. If a warranty concern has not been resolved using the three-step 246

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Customer Assistance

procedure outlined on the first page of the Customer Assistance section, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration. During mediation, a representative of the BBB will contact both you and Ford Motor Company to explore options for settlement of the claim. If an agreement is not reached during mediation and your claim is eligible, you may participate in the arbitration process. An arbitration hearing will be scheduled so that you can present your case in an informal setting before an impartial person. The arbitrator will consider the testimony provided and make a decision after the hearing. You are not bound by the decision, but should you choose to accept the BBB AUTO LINE decision, Ford must abide by the accepted decision as well. Disputes submitted to the BBB AUTO LINE program are usually decided within forty days after you file your claim with the BBB. BBB AUTO LINE Application: Using the information provided below, please call or write to request a program application. You will be asked for your name and address, general information about your new vehicle, information about your warranty concerns, and any steps you have already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. You can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to: BBB AUTO LINE 4200 Wilson Boulevard, Suite 800
Arlington, Virginia 22203–1833
BBB AUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673. Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation.

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).

247

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Customer Assistance

The CAMVAP program is a straight forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding to both you and Ford of Canada. CAMVAP services are available in all territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685.

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a regional office or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. Using leaded fuel may also result in difficulty importing your vehicle back into the U.S. If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY FORD EXPORT OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (313) 594-4857
FAX: (313) 390-0804
Email: [email protected] 248

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Customer Assistance

If you are in another foreign country, contact the nearest authorized dealer. If the authorized dealer employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations. Customers in the U.S. should call 1-800-392-3673.

ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED P.O. Box 07150
Detroit, Michigan 48207
Or to order a free publication catalog, call toll free: 1-800-782-4356
Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com. (Items in this catalog may be purchased by credit card, check or money order.)

Obtaining a French Owner’s Guide French Owner’s Guides can be obtained from your authorized dealer or by writing to: Ford Motor Company of Canada, Limited Service Publications CHQ202
The Canadian Road P.O. Box 2000
Oakville, ON, Canada L6J 5E4

249

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Customer Assistance

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov; or write to: Administrator 1200 New Jersey Avenue, Southeast Washington, D.C. 20590
You can also obtain other information about motor vehicle safety from http://www.safercar.gov.

REPORTING SAFETY DEFECTS (CANADA ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Transport Canada, using their toll-free number: 1–800–333–0510.

250

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Cleaning

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing

or laundry liquid. These products can discolor and spot painted surfaces. • Using high pressure water or wand-type car washes may cause

strong, direct sunlight.

damage to tape stripes if the nozzle is positioned closer than 12 inches (30 cm) from the stripe. • Never wash a vehicle that is “hot to the touch” or during exposure to • Always use a clean sponge or car wash mitt with plenty of water for • Dry the vehicle with a chamois or soft terry cloth towel in order to • It is especially important to wash the vehicle regularly during the

eliminate water spotting.

best results.

winter months, as dirt and road salt are difficult to remove and cause damage to the vehicle. • Immediately remove items such as gasoline, diesel fuel, bird droppings

and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time. Use Bug and Tar Remover (ZC-42) which is available from your authorized dealer.

• Remove any exterior accessories, such as antennas, before entering a • Suntan lotions and insect repellents can damage any painted surface; if these substances come in contact with your vehicle, wash off as soon as possible.

car wash.

Exterior chrome • Wash the vehicle first, using cool or lukewarm water and a neutral pH • Use Custom Bright Metal Cleaner (ZC-15), available from your

shampoo, such as Motorcraft威 Detail Wash (ZC-3-A).

authorized dealer. Apply the product as you would a wax to clean bumpers and other chrome parts; allow the cleaner to dry for a few minutes, then wipe off the haze with a clean, dry rag.

• Never use abrasive materials such as steel wool or plastic pads

as they can scratch the chrome surface.

251

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Cleaning

WAXING • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft威 Premium

Liquid Wax (ZC-53-A), which is available from your authorized dealer, or an equivalent quality product.

• Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time.

spots, road salt and industrial fallout before repairing paint chips.

PAINT CHIPS Your authorized dealer has touch-up paint to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jamb) to your authorized dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish. In order to maintain their shine: • Clean weekly with Motorcraft威 Wheel and Tire Cleaner (ZC-37-A), which is available from your authorized dealer. Heavy dirt and brake dust accumulation may require agitation with a sponge. Rinse thoroughly with a strong stream of water.

• Never apply any cleaning chemical to hot or warm wheel rims or • Some automatic car washes may cause damage to the finish on your wheel rims or covers. Chemical-strength cleaners, or cleaning chemicals, in combination with brush agitation to remove brake dust and dirt, could wear away the clearcoat finish over time.

• Do not use hydrofluoric acid-based or high caustic-based wheel • To remove tar and grease, use Motorcraft威 Bug and Tar Remover

cleaners, steel wool, fuels or strong household detergent.

covers.

(ZC-42), available from your authorized dealer.

252

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Cleaning

ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the • Spray Motorcraft威 Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft威 Engine Shampoo (CXC-66-A).

engine block or other engine components.

running engine may cause internal damage.

• Never wash or rinse the engine while it is running; water in the • Never wash or rinse any ignition coil, spark plug wire or spark plug • Cover the highlighted areas to prevent water damage when cleaning

well, or the area in and around these locations.

the engine.

4.0L V6 ENGINE

253

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Cleaning

4.6L 3V V8 ENGINE

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer. • For routine cleaning, use Motorcraft威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft威 Bug and Tar

Remover (ZC-42).

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly. If the wipers do not wipe properly, substances on the vehicle’s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellent coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. To clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned with

a non-abrasive cleaner such as Motorcraft威 Ultra-Clear Spray Glass

254

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Cleaning

Cleaner (ZC-23) in the U.S., or Premium Quality Windshield Washer Fluid [CXC-37-(A, B, D, or F)] in Canada, available from your authorized dealer.

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol or

Motorcraft威 Premium Windshield Washer Concentrate (ZC-32-A), available from your authorized dealer. This washer fluid contains special solution in addition to alcohol which helps to remove the hot wax deposited on the wiper blade and windshield from automated car wash facilities. Be sure to replace wiper blades when they appear worn or do not function properly.

• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. If you cannot remove those streaks after cleaning with the glass cleaner or if the wipers chatter and move in a jerky motion, clean the outer surface of the windshield and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaning solution. After cleaning, rinse the windshield and wiper blades with clean water. The windshield is clean if beads do not form when you rinse the windshield with water.

CONVERTIBLE TOP AND PADDED MOLDING For vinyl tops, wash with Motorcraft威 Triple Clean (ZC-13), which is available from your authorized dealer. For cloth tops wash with a high quality convertible top cleaner/protectant. • Do not use stiff bristle brushes or abrasive materials or cleaners. • Hot waxes applied by commercial car washes can affect the • Using high water pressure or wand-type car washes against the

cleanability of vinyl material.

convertible top and windows may cause water leaks and possible seal damage.

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with a clean, damp, white cotton cloth, then use a clean and dry white cotton cloth to dry these areas. • Avoid cleaners or polishes that increase the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.

255

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Cleaning • Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the

finish of the instrument panel, interior trim and cluster lens.

WARNING: Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid

contamination of the airbag system.

If a staining liquid like coffee/juice has been spilled on the instrument panel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Wipe the surface with a damp, clean, white cotton cloth. For more thorough cleaning, use a mild soap and water solution. If the spot cannot be completely cleaned by this method, the area may be cleaned using a commercially available cleaning product designed for automotive interiors. 3. If necessary, apply more soap and water solution or cleaning product to a clean, white, cotton cloth and press the cloth onto the soiled area–allow this to set at room temperature for 30 minutes. 4. Remove the soaked cloth, and if it is not soiled badly, use this cloth to clean the area by using a rubbing motion for 60 seconds. 5. Following this, wipe area dry with a clean, white, cotton cloth.

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side airbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft威 Professional Strength • If grease or tar is present on the material, spot-clean the area first with Motorcraft威 Spot and Stain Remover (ZC-14). In Canada, use Motorcraft威 Multi-Purpose Cleaner (CXC-101).

Carpet & Upholstery Cleaner (ZC-54).

immediately (but do not oversaturate) or the ring will set.

• If a ring forms on the fabric after spot cleaning, clean the entire area • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.

256

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Cleaning

WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt

webbing.

WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and affect performance of the side airbag in a collision.

LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over the leather. • For routine cleaning, wipe the surface with a soft, damp cloth. For

more thorough cleaning, wipe the surface with a mild soap and water solution. In Canada, use Motorcraft威 Vinyl Cleaner (CXC-93). Dry the area with a soft cloth.

• If the leather cannot be completely cleaned using a mild soap and water solution, the leather may be cleaned using a commercially available cleaning product designed for automotive leather.

• Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl and plastics, or oil/petroleum-based leather conditioners. These products may cause premature wearing of the clear, protective coating.

Note: In some instances, color or dye transfer can occur when wet clothing comes in contact with leather upholstery. If this occurs, the leather should be cleaned immediately to avoid permanent staining.

UNDERBODY Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt.

257

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Cleaning

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft威 Bug and Tar Remover (ZC-42) Motorcraft威 Custom Bright Metal Cleaner (ZC-15) Motorcraft威 Custom Clear Coat Polish (ZC-8-A) Motorcraft威 Detail Wash (ZC-3-A) Motorcraft威 Dusting Cloth (ZC-24) Motorcraft威 Engine Shampoo and Degreaser (U.S. only) (ZC-20) Motorcraft威 Engine Shampoo (Canada only) (CXC-66-A) Motorcraft威 Multi-Purpose Cleaner (Canada only) (CXC-101) Motorcraft威 Premium Glass Cleaner (Canada only) (CXC-100) Motorcraft威 Premium Liquid Wax (ZC-53-A) Motorcraft威 Premium Windshield Washer Concentrate (U.S. only) (ZC-32-A) Motorcraft威 Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft威 Spot and Stain Remover (U.S. only) (ZC-14) Motorcraft威 Tire Clean and Shine (ZC-28) Motorcraft威 Ultra-Clear Spray Glass Cleaner (ZC-23) Motorcraft威 Vinyl Cleaner (Canada only) (CXC-93) Motorcraft威 Wheel and Tire Cleaner (ZC-37-A)

258

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your Warranty Guide/Customer Information Guide to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Motorcraft威 parts are designed and built to provide the best performance in your vehicle.

PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work on a hot engine. • Make sure that nothing gets caught in moving parts. • Do not work on a vehicle with the engine running in an enclosed • Keep all open flames and other burning material (such as cigarettes)

space, unless you are sure you have enough ventilation.

away from the battery and all fuel related parts.

Working with the engine off 1. For vehicles equipped with an automatic transmission, set the parking brake and shift to P (Park). For vehicles equipped with a manual transmission, set the parking brake, press and hold the clutch pedal, place the gearshift in 1 (First), and release the clutch pedal. 2. Turn off the engine and remove the key. 3. Block the wheels.

Working with the engine on 1. For vehicles equipped with an automatic transmission, set the parking brake and shift to P (Park). For vehicles equipped with a manual transmission, set the parking brake, press and hold the clutch pedal, place the gearshift in N (Neutral), and release the clutch pedal. 2. Block the wheels.

WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running.

259

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located on the driver’s side kick panel.

2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood and secure it with the prop rod.

260

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT

4.0L V6 engine

1. Battery 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power distribution box

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

261

Maintenance and Specifications

4.6L 3V V8 engine

1. Battery 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power distribution box

262

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications

Engine shield

Some vehicles may be equipped with an aero-shield under the engine. This shield needs to be removed for service, including oil and filter changes. It is secured with four screws.

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smearing. Refer to Maintenance product specifications and capacities in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.

WARNING: If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze protection. Failure

to use washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.

263

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications

CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it.

3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optimum performance. Poor wiper quality can be improved by cleaning the wiper blades and the windshield. Refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended to scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.

ENGINE OIL

Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait 15 minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park) (automatic transmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 264

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications

5. Locate and carefully remove the engine oil level dipstick. • 4.0L V6 engine

• 4.6L V8 engine

6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is between the lower and upper holes, the oil level

is acceptable. DO NOT ADD OIL.

265

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications • If the oil level is below the lower hole, add enough oil to raise the • 4.0L V6 engine

level within the lower and upper holes.

• 4.6L V8 engine

• Oil levels above the upper hole may cause engine damage. Some oil

must be removed from the engine by an authorized dealer.

7. Put the dipstick back in and ensure it is fully seated.

266

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the normal operating range on the engine oil level dipstick. 4. Install the dipstick and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise 1/4 of a turn until three clicks are heard or until the cap is fully seated. To avoid possible oil loss, DO NOT operate the vehicle with the engine oil level dipstick and/or the engine oil filler cap removed.

Engine oil and filter recommendations 4.0L V6 Engine Look for this certification trademark.

Use SAE 5W-30 engine oil Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. To protect your engine and engine’s warranty, use Motorcraft威 SAE 5W-30 or an equivalent SAE 5W-30 oil meeting Ford specification WSS-M2C929-A. Refer to Maintenance product specifications and capacities later in this section for more information.

267

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications

Do not use supplemental engine oil additives, cleaners or other engine treatments. They are unnecessary and could lead to engine damage that is not covered by Ford warranty. Change your engine oil according to the appropriate schedule listed in the scheduled maintenance information. Ford production and Motorcraft威 replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft威 oil filter or another with equivalent performance for your engine application. 4.6L 3V V8 Engine Look for this certification trademark.

Use SAE 5W-20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. To protect your engine and engine’s warranty, use Motorcraft威 SAE 5W-20 or an equivalent SAE 5W-20 oil meeting Ford specification WSS-M2C930-A. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine. Refer to Maintenance product specifications and capacities later in this section for more information. Do not use supplemental engine oil additives, cleaners or other engine treatments. They are unnecessary and could lead to engine damage that is not covered by Ford warranty. 268

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications

Change your engine oil according to the appropriate schedule listed in the scheduled maintenance information. Ford production and Motorcraft威 replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft威 oil filter or another with equivalent performance for your engine application. BATTERY Your vehicle is equipped with a Motorcraft威 maintenance-free battery which normally does not require additional water during its life of service.

If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. It is recommended that the negative battery cable terminal be disconnected from the battery if you plan to store your vehicle for an extended period of time. This will minimize the discharge of your battery during storage. Note: Electrical or electronic accessories or components added to the vehicle by the dealer or the owner may adversely affect battery performance and durability.

WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.

269

2010 05+ Mustang (197) Owners Guide, 3rd Printing USA (fus)

Maintenance and Specifications

WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.

WARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.

Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.

WARNING: Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.

Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more to • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.

relearn the idle and fuel trim strategy.