2001 Ford F 250 Owners Manual

should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.

ADD

COLD

HOT

DO NOT ADD

DON'T ADD IF IN CROSSHATCHED AREA (cid:127) CHECK WHEN HOT

IDLING IN PARK

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level.

3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely.

Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.

216

Maintenance and care

Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level.

3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening.

Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.

AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft Part Numbers. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running.

217

Maintenance and care

Changing the air filter element (gasoline engines only) 1. Loosen the clamp that secures the air filter element in place.

2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the open end of the air filter housing.

4. Install a new air filter element, ensuring the arrow on the top half of the air filter housing lines up with the notch on the bottom half of air filter housing. Be careful not to crimp the filter element edges between the air filter housing. This could cause filter damage and allow unmetered air to enter the engine if not properly seated. 5. Replace the two halves of the air filter housing and secure the clamp.

218

Maintenance and care

DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that require lubrication. Refer to the scheduled maintenance guide for maintenance intervals. If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will also be necessary.

BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.

However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells. If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high mineral or alkali content). If possible, however, try to only fill the battery cells with distilled water. If the battery needs water often, have the charging system checked. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. When the battery is disconnected or a new battery installed, the transmission must learn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will fully update transmission operation to its optimum shift feel.

219

Maintenance and care

Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted

substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.

When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps,

resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.

Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.

Battery posts, terminals and related accessories contain lead and lead compunds. Wash hands after handling.

For information on transmission operation after the battery has been disconnected see “Shift strategy” in the driving section. Because your vehicle’s engine is also electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute.

220

Maintenance and care

relearn the idle and fuel trim strategy.

6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 16 km (10 miles) or more to • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.

If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.

RECYCLE

WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades.

Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent. Rinse thoroughly with clean water. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.

221

Maintenance and care

Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard.

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic tires for use on passenger cars. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.

222

Maintenance and care

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.

Traction AA A B C The traction grades, from highest to lowest are AA, A, B, and C. Those grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include

acceleration, cornering, hydroplaning or peak traction characteristics.

Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed,

underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

223

Maintenance and care

SERVICING YOUR TIRES

Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been

parked for at least one hour or has been driven less than 5 km (3 miles).

• Adjust tire pressure to recommended specifications found on the Certification Label. Tire pressure information can also be found on the Tire Information label located on the inside of the fuel filler door.

Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control.

Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the scheduled maintenance guide. If you notice that the tires wear unevenly, have them checked. The following procedure applies to vehicles equipped with single rear wheels, if your vehicle is equipped with dual rear wheels it is recommended that only the front wheels be rotated (side to side). • Four tire rotation

224

• Five tire rotation

Maintenance and care

Replacing the tires Replace the tires when the wear band is visible through the tire treads.

When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the

Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label. If you do not follow these precautions, your vehicle may not drive properly and safely.

Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”, etc.),

as originally offered by Ford.

225

Maintenance and care

Do not replace your tires with “high performance” tires or larger size tires.

Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose

control and roll over.

Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer.

SNOW TIRES AND CHAINS

Snow tires must be the same size and grade as the tires you currently have on your vehicle.

The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same size and specifications) be used as chains may chip aluminum wheels. Follow these guidelines when using snow tires and chains: • Use only SAE Class S chains. • Install chains securely, verifying that the chains do not touch any • Drive cautiously. If you hear the chains rub or bang against your

wiring, brake lines or fuel lines.

vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent damage to your vehicle.

• If possible, avoid fully loading your vehicle. • Remove the tire chains when they are no longer needed. Do not use • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.

tire chains on dry roads.

226

Maintenance and care

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS

Important safety precautions

Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.

The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops

before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.

If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.

Automotive fuels can cause serious injury or death if misused or mishandled.

Gasoline may contain benzene, which is a cancer-causing agent.

227

Maintenance and care

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials

and any open flames before fueling your vehicle.

fueling.

• Always turn off the vehicle before • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind

can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury.

• Fuels can also be harmful if absorbed through the skin. If fuel is

splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.

When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while

refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes.

228

Maintenance and care

The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an

ungrounded fuel container.

Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the • Keep the fuel pump nozzle in contact with the fuel container while • DO NOT use a device that would hold the fuel pump handle in the fill

cargo area).

filling.

position.

Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Do not use fuel containing methanol. It can damage critical fuel system components. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based compounds containing MMT. Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty.

Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. We do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage.

87(R+M)/2 METHOD

229

Maintenance and care

Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced. If the problems persist, see your dealer or a qualified service technician. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quality fuel of the recommended octane rating. Aftermarket products could cause damage to the fuel system. Repairs to correct the effects of using an aftermarket product in your fuel may not be covered by your warranty. Many of the world’s automakers issued the World-wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle. Gasolines that meet the World-wide Fuel Charter should be used when available. Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter. In Canada, look for fuels that display the Auto Makers’ Choice娂 logo.

Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality.

Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after

refueling, to allow the fuel system to pump the fuel from the tank to the engine.

• Your “Service Engine Soon” indicator may come on. For more information on the “Service Engine Soon” indicator, refer to the Instrumentation chapter.

230

Maintenance and care

Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/off feature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops. If the “Service Engine Soon/Check Engine” indicator comes on and stays on after you start the engine, the fuel filler cap may not be properly installed. Turn off the engine, remove the fuel filler cap, align the cap properly and reinstall it. If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used.

The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops

before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.

If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.

Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to the scheduled maintenance guide for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used.

231

Maintenance and care

ESSENTIALS OF GOOD FUEL ECONOMY

Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1 600 km (1 000
miles) of driving (engine break-in period). You will get a more accurate measurement after 3 000 km–5 000 km (2 000 miles-3 000 miles).

Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill capacities section of the Capacities and specifications chapter. The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty. Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling, • Use the same filling rate setting (low — medium — high) each time • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent.

an error in the reading will result if the engine is left running.

same direction each time you fill up.

the tank is filled.

232

Maintenance and care

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy:

Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used.

Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter will show how temperature impacts fuel economy. In general, lower temperatures give lower fuel economy.

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel • Idling for long periods of time (greater than one minute) may waste • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually.

economy.

fuel.

233

less fuel than traveling at 105 km/h [65 mph]).

Maintenance and care • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy.

reduce fuel economy.

• Warming up a vehicle on cold mornings is not required and may • Resting your foot on the brake pedal while driving may reduce fuel • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel • Perform all regularly scheduled maintenance items. Follow the

economy.

economy.

recommended maintenance schedule and owner maintenance checks found in your vehicle scheduled maintenance guide.

at any speed.

Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy • Carrying unnecessary weight may reduce fuel economy (approximately • Adding certain accessories to your vehicle (for example bug

0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried).

deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy.

• Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first • Driving on flat terrain offers improved fuel economy as compared to

12–16 km (8–10 miles) of driving.

driving on hilly terrain.

234

two-wheel-drive operation.

cruise gear and with steady pressure on the gas pedal.

Maintenance and care • Transmissions give their best fuel economy when operated in the top • Four-wheel-drive operation (if equipped) is less fuel efficient than • Close windows for high speed driving. EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of L/100 km (MPG) expected on the vehicle under optimum conditions. Your fuel economy may vary depending upon the method of operation and conditions.

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. • Avoid running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at • Have the items listed in your scheduled maintenance guide performed

high speeds.

according to the specified schedule.

The scheduled maintenance items listed in the scheduled maintenance guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.

235

Maintenance and care

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine

compartment and exhaust system, which can start a fire.

Illumination of the “Service Engine Soon” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly.

Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment.

Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your Warranty Guide for complete emission warranty information.

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the Warning lights and chimes section of the Instrumentation chapter. Your vehicle may not pass the I/M test with the “Check Engine/Service Engine Soon” light on. If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop-and-go, city-type traffic with

at least four idle periods.

236

Maintenance and care

Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete.

BULBS

Replacing exterior bulbs Check the operation of the following lamps frequently: • Headlamps • High-mount brakelamp • Brakelamps • Turn signals • License plate lamp • Tail lamps • Back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance.

Replacing headlamp bulbs (aerodynamic) 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove bulb retainer ring by turning it counterclockwise, then slide the ring off the plastic base. 5. Without turning, carefully pull bulb out of headlamp assembly.

237

Maintenance and care

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

6. Insert the glass end of the new bulb into the headlamp assembly. When the grooves in the plastic base are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly. 7. Install bulb retaining ring over the plastic base and lock the ring into the socket by turning it clockwise until you feel a “stop.” 8. Connect the electrical connector into the rear of the plastic base until it “snaps.” Replacing headlamp bulbs (sealed beam) To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position. 2. Open the hood. 3. Remove the two screws and parking lamp/side marker assembly by pulling gently 4. Disconnect the electrical connectors from the parking lamp/side marker assembly and remove.

5. Remove the four bolts and headlamp bezel.

238

Maintenance and care

6. Remove the four screws and the headlamp retaining ring from headlamp. 7. Disconnect the electrical connector and remove headlamp.

To install the new headlamp, reverse the removal procedure. Replacing front parking/turn signal bulbs 1. Make sure headlamp switch is in OFF position. 2. Open the hood. 3. Remove the two screws and carefully disengage parking lamp/turn signal assembly from the vehicle.

4. Rotate bulb socket counterclockwise about 1⁄4 turn and remove from lamp assembly.

239

Maintenance and care

5. Carefully pull bulb straight out of the socket and push in the new bulb. 6. Install the bulb socket in lamp assembly by turning clockwise. 7. Align the lamp assembly on the vehicle. 8. Install two screws on parking lamp/turn signal assembly. Replacing tail lamp/turn/backup lamp bulbs — F250/F350 only The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the tailgate to expose the lamp assemblies. 2. Remove the two bolts from the tail lamp assembly. 3. Carefully pull the lamp assembly from the tailgate pillar by releasing the two retaining tabs. 4. Twist the bulb socket 1⁄4 turn counterclockwise and remove from lamp assembly. 5. Pull the bulb straight out of the socket and push in the new bulb. 6. Install bulb socket in lamp assembly by turning clockwise. 7. Carefully install the tail lamp assembly on tailgate pillar snapping the two retaining tabs into place. 8. Secure the tail lamp with two bolts.

240

Maintenance and care

Replacing brake/tail/backup lamp bulbs — F450/F550 only The brake/tail/backup lamp bulbs are located in the same portion of the tail lamp assembly. Follow the same steps to replace either bulb: 1. Remove the four screws and the lamp lens from lamp assembly. 2. Carefully pull the bulb straight out of the socket and push in the new bulb. 3. Install the lens on the lamp assembly with the four screws.

Replacing cargo lamp and high-mount brakelamp bulbs To remove the lamp assembly: 1. Remove the two screws and lamp assembly from vehicle as wiring permits. 2. Remove the bulb socket by rotating counterclockwise and pulling it out of the lamp assembly. 3. Pull the bulb straight out of the socket and push in the new bulb. To install the brakelamp assembly: 1. Install the bulb into the lamp assembly and rotate clockwise. 2. Install the lamp assembly on the vehicle with two screws.

241

Maintenance and care

Replacing roof marker bulbs To change the cab marker bulbs: 1. Remove the screw and lens from the lamp assembly. 2. Carefully pull the bulb straight out of the socket and push in the new bulb. 3. Install lens on lamp assembly with screw.

Replacing foglamp bulbs (if equipped) 1. Remove the bulb socket from the foglamp by turning counterclockwise. 2. Disconnect the electrical connector from the foglamp bulb. 3. Connect the new foglamp bulb to the electrical connector. 4. Install the bulb socket in the foglamp by turning clockwise. Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper. To change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2. Twist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly. 3. Pull out the old bulb from the socket and push in the new bulb. 4. Install the bulb socket in lamp assembly by turning it clockwise.

242

Maintenance and care

Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.

Function

Number of

Trade number

bulbs

Headlamps (aerodynamic) Headlamps (sealed beam) Park/turn Sidemarker Tail/stop/turn/sidemarker Backup High-mount stoplamp Foglamp License plate lamp Cargo lamp Roofmarker Rear fender clearance Interior visor lamp (if equipped) Rear identification All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer (a) Replace entire lamp assembly; bulb is not serviceable.

9007
H6054
3157
194

3157 K 3156K

921
899
168
906
194
(a)

194
194

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician.

CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approved cleaners, polishes and waxes.

243

Maintenance and care

Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. To avoid spots, avoid washing when the hood is still warm, immediately after or during exposure to strong sunlight. During winter months, it is especially important to wash the vehicle on a regular basis. Large quantities of dirt and road salt are difficult to remove and also cause damage to the vehicle. Any gasoline spilled on the vehicle or deposits such as bird droppings should be washed and sponged off as soon as possible. Deposits not removed promptly can cause damage to the vehicle’s paintwork. Remove any exterior accessories (such as antennas) and fold in the side view mirrors before entering a car wash. If you have wax applied to the vehicle at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield. After washing, apply the brakes several times to dry them.

Underbody Flush the complete underside of vehicle frequently. Keep body drain holes unplugged. Inspect for road damage.

Waxing your vehicle Waxing your vehicle on a regular basis will reduce minor scratches and paint damage. Wax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use a cleaning fluid with a clean cloth to remove any bugs before waxing your vehicle. Use tar remover to remove any tar spots.

244

Maintenance and care

Avoid getting wax on the windshield, or on any surfaces which appear coarse or bumpy. If you have wax applied at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield.

Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra Touch Prep and Finishing Kit (F7AZ-19K507–BA), Lacquer Touch-up Paint (ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above) will vary with your vehicle’s specific coloring. Observe the application instructions on the products. Remove particles such as bird droppings, tree sap, insect remains, tar spots, road salt and industrial fallout immediately.

Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces. Use a tar remover to remove grease and tar. The brushes used in some automatic car washes may damage the finish on your wheels. Before going to a car wash, find out if the brushes are abrasive.

245

Maintenance and care

Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray with cold water to avoid cracking the engine block or • Never wash or rinse the engine while it is running; water in the

other engine components.

running engine may cause internal damage.

Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners.

Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. If necessary, use a tar remover such as Ford Extra Strength Tar and Road Oil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners.

246

Maintenance and care

Cleaning the windshield, wiper blades and rear window If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. If the wiper still does not wipe properly, this could be caused by substances on the windshield or rear window such as tree sap and some hot wax treatments used by commercial car washes. Clean the outside of the windshield or rear window with a non-abrasive cleaner such as Ford Ultra-Clear Spray Glass Cleaner, (E4AZ-19C507–AA), available from your Ford Dealer. Do not use abrasive cleansers on glass as they may cause scratches. The windshield or rear window is clean if beads do not form when you rinse it with water. The windshield, rear window and wiper blades should be cleaned on a regular basis, and blades or rubber elements replaced when worn.

Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.

Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of

the air bag system.

Cleaning the instrument cluster lens Clean with a damp cloth, then dry with a dry cloth. Do not use household or glass cleaners as these may damage the lens.

Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner. Remove fresh spots immediately. Do not use household or glass cleaners. These agents can stain and discolor the fabric. Use a mild soap and water solution if necessary.

247

Maintenance and care

Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, tears or cuts. If your vehicle has been involved in an accident, refer to the Safety belt maintenance section in the Seating and safety restraints chapter.

Cleaning leather seats (if equipped) To clean, simply use a soft cloth dampened with water and a mild soap. Wipe the leather again with a damp cloth to remove soap residue. Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer. This mild cleaner and special pad, cleans the leather and maintains its natural beauty. Follow the instructions on the cleaner label. Regular cleaning of your leather upholstery helps maintain its resiliency and color. Do not use household cleaning products, alcohol solutions, solvents or cleaners intended for rubber, vinyl or plastics.

248

Capacities and specifications

5.4L V8 engine FA-1634
FG-986B FL-820-S EV-233
BXT-65-650
BXT-65-750
AWSF-22W

MOTORCRAFT PART NUMBERS Component* Air filter element Fuel filter Oil filter PCV valve Battery (Standard) Battery (Optional) Spark plugs-platinum** *Refer to the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for Motorcraft diesel engine service part numbers. **Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.

6.8L V10 engine FA-1634
FG-986B FL-820-S EV-233
BXT-65-650
BXT-65-750
AWSF-22W

REFILL CAPACITIES

Fluid

Front axle

Rear axle 1,2

Ford Part

Name

Motorcraft SAE 75W-90
Premium 4x4
Front Axle Lubricant Motorcraft SAE 75W-140
Synthetic Rear Axle Lubricant

Motorcraft SAE 80W-90
Premium Rear Axle Lubricant

Application

Capacity

F-250/350
(Dana 50 axle)

F-350/450/550
(Dana 60 axle)

F-250 /350
(10.50 inch axle) F-350 DRW (DANA 80) F-550 Dana 135

1.8L (3.8 pints)

2.7L (5.8 pints)

3.3L (6.9 pints)

4.0L (8.5 pints)

11.6L (24.5
pints)

249

Capacities and specifications

Fluid

Brake fluid

Ford Part

Name

High Performance DOT 3 Motor Vehicle Brake Fluid

Engine coolant 3 Motorcraft

Application

Capacity

All

Fill to line on reservoir

5.4L V8 engine with A/C

25.0L (26.4
quarts)

6.8L V10 engine 27.0L (28.5

Premium Engine Coolant (green-colored) or Motorcraft Premium Gold Engine Coolant (yellow-colored) Motorcraft SAE 5W-20 Super Premium Motor Oil Refer to your 7.3L Diesel Supplement

All

quarts)

5.7L (6.0
quarts)

Engine oil (includes filter change)-Gas engines Engine oil (includes filter change)-Diesel engine

250

Capacities and specifications

Fluid

Ford Part

Name

Fuel tank

N/A

Power steering fluid Transfer case fluid Transmission fluid 4

Motorcraft MERCON威 ATF Motorcraft MERCON威 ATF Synthetic MERCON威 ATF Motorcraft MERCON威 ATF

Windshield washer fluid

Ultra-Clear Windshield Washer Concentrate

Application

Capacity

Mid-ship tank (optional on Chassis Cab) Right side saddle mounted tank (optional on Chassis Cab) Short box

Long box

Aft axle

All

4x4 vehicles

5-speed manual

6-speed manual

Automatic

All

71.9L (19.0
gallons)

87.1L (23.0
gallons)

109.8L (29.0
gallons) 143.9L (38.0
gallons) 151.4L (40.0
gallons) Fill to line on reservoir 1.9L (2.0
quarts) 3.2L (3.4
quarts) 5
5.5L (5.8
quarts) 5
16.7L (17.7
quarts) 6
4.0L (4.25
quarts)

1Your vehicle’s rear axle(s) may be filled with a synthetic lubricant that may require a lubricant change. Refer to the scheduled maintenance guide. Axle lubricant quantities should not need to be checked unless a leak is suspected, service is required or the axle assembly has been submerged in water. The axle lubricant should be changed any time the rear axle has been submerged in water.

251

Capacities and specifications

2Add 236 ml (8 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford Specification EST-M2C118-A for complete refill of Traction-Lok axles. 3Add the coolant type originally equipped in your vehicle. 4Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle. Check the container to verify the fluid being added is of the correct type. Refer to your scheduled maintenance guide to determine the correct service interval. Some transmission fluids may be labeled as dual usage, such as MERCON威 and MERCON威 V. These dual usage fluids are not to be used in an automatic transmission that requires use of the MERCON威 type fluid. However, these dual usage fluids may be used in transmissions that require the MERCON威 V type fluid. MERCON威 and MERCON威 V type fluids are not interchangeable. DO NOT mix MERCON威 and MERCON威 V. Use of a transmission fluid that indicates dual usage (MERCON威 and MERCON威 V) in an automatic transmission application requiring MERCON威 may cause transmission damage. Use of any fluid other than the recommended fluid may cause transmission damage. 5Service refill capacity is determined by filling the transmission to the bottom of the filler hole with the vehicle on a level surface. 6Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with an in-tank cooler. The amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range.

252

Capacities and specifications

LUBRICANT SPECIFICATIONS

Item

Front axle (4X4)

Rear axle

Brake fluid and clutch fluid (if equipped)

Ford part name or equivalent Motorcraft SAE 75W-90
Premium 4x4
Front Axle Lubricant Motorcraft SAE 75W-140 High Performance Synthetic Rear Axle Lube 1
Motorcraft SAE 80W-90
Premium Rear Axle Lubricant (Dana 135
axles) 1
High Performance DOT 3 Motor Vehicle Brake Fluid

Engine coolant Motorcraft

Premium Engine Coolant (green-colored) Motorcraft Premium Gold Engine Coolant (yellow-colored)

Ford part number

Ford specification

XY-75W90-TQL WSP-M2C201-A

F1TZ-19580-B

WSL-M2C192-A

XY-80W90-QL

WSP-M2C197-A

C6AZ-19542-AB ESA-M6C25-A

and DOT 3

VC-4–A (in Canada, Motorcraft CXC-10) VC-7–A

ESE-M97B44-A

WSS-M97B51-A1

253

Capacities and specifications

Ford part name or equivalent Motorcraft SAE 5W-20 Super Premium Motor Oil Multi-Purpose Grease

Motorcraft penetrating and lock lubricant Premium Long-Life Grease

Ford part number

Ford specification

XO-5W20-QSP WSS-M2C153-H

and API Certification Mark ESB-M1C93-B or ESR-M1C159-A

DOAZ-19584-AA or F5AZ-19G209-AA

Motorcraft XL-1

none

XG-1-C or XG-1-K

ESA-M1C75-B

Motorcraft MERCON威 ATF

XT-2-QDX

MERCON威

Synthetic MERCON威 ATF

Motorcraft MERCON威 ATF

E6AZ-19582-B

MERCON威

XT-2-QDX

MERCON威

Item

Engine oil

Hinges, latches, striker plates, fuel filler door hinge and seat tracks

Lock cylinders

Transmission /steering/parking brake linkages and pivots, brake and clutch pedal shaft (if equipped) Power steering fluid and transfer case fluid (if equipped) Manual transmission (5-speed) Manual transmission (6-speed)

254

Capacities and specifications

Item

Automatic transmission

Windshield washer fluid

Ford part name or equivalent Motorcraft MERCON威 ATF

Ultra-clear Windshield Washer Concentrate

Ford part number

XT-2-QDX

Ford specification

MERCON威

C9AZ-19550-AC ESR-M17P5-A

1Add 236 ml (8 oz.) of Additive Friction Modifier C8AZ-19B546-A or equivalent meeting Ford specification EST-M2C118-A for complete refill of Traction-Lok axles. Ford design rear axles contain a synthetic lubricant that does not require changing unless the axle has been submerged in water. Dana rear axles also contain a synthetic lubricant but do require a change. Refer to your “Service Guide” for change intervals on Dana rear axles. 2Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle. Check the container to verify the fluid being added is of the correct type. Refer to your scheduled maintenance guide to determine the correct service interval. Some transmission fluids may be labeled as dual usage, such as MERCON威 and MERCON威 V. These dual usage fluids are not to be used in an automatic transmission that requires use of the MERCON威 type fluid. However, these dual usage fluids may be used in transmissions that require the MERCON威 V type fluid. MERCON威 and MERCON威 V type fluids are not interchangeable. DO NOT mix MERCON威 and MERCON威 V. Use of a transmission fluid that indicates dual usage (MERCON威 and MERCON威 V) in an automatic transmission application requiring MERCON威 may cause transmission damage. Use of any fluid other than the recommended fluid may cause transmission damage.

255

Capacities and specifications

ENGINE DATA Engine Cubic inches Required fuel Firing order

Spark plug gap

Ignition system Compression ratio

VEHICLE DIMENSIONS

F250–except Crew Cab Dimension

5.4L V8 engine 330
87 octane 1-3-7-2-6-5-4-8
1.3-1.4 mm (0.052-0.056 inch) Coil on plug 9.0:1

6.8L V10 engine 415
87 octane 1-6-5-10-2-7-3-8-4-9
1.3-1.4 mm (0.052-0.056 inch) Coil on plug 9.0:1

Body style

Regular Cab 4x2
1 864 mm (74 in) 1 736.3 mm (68.3 in) / 1 729.3 mm (68 in) 2 031 mm (79.9 in) 3 479.8 mm (137 in)

Regular Cab 4x4
1 958 mm (77.1 in) 1 736.3 mm (68.3 in) / 1 729.3 mm (68 in) 2 031 mm (79.9 in) 3 479.8 mm (137 in)

(1) Overall height (2) Track (Front / Rear)

(3) Overall width (4) Wheelbase

(5) Overall length

5 646 mm (222.2 in)

5 757 mm (226.6 in)

Super Cab 4x2
1 870 mm (73.6 in) 1 736.3 mm (68.3 in) / 1 729.3 mm (68 in) 2 031 mm (79.9 in) 3 601.7 mm (141.8 in)a 4 013.2 mm (158 in)b 5 876 mm (231.3 in)a 6 177 mm (243.1 in)b

Super Cab 4x4
1 964 mm (77.3 in) 1 736.3 mm (68.3 in) / 1 729.3 mm (68 in) 2 031 mm (79.9 in) 3 601.7 mm (141.8 in)a 4 013.2 mm (158 in)b 5 879 mm (231.4 in)a 6 180 mm (243.3 in)b

aShort wheel base bLong wheel base

256

Capacities and specifications

Body style

Crew Cab 4x2

1 960 mm (77.2 in)a/ 1 883 mm (74.1 in)b 1 745 mm (68.7 in)/ 1 729 mm (68.1 in)a,b 1 988 mm (78.3 in)a,b 3 967 mm (156.2 in )a/ 4 379 mm (172.4 in)b 6 242 mm (245.8 in)a/ 6 654 mm (262.0 in)b

Crew Cab 4x4
2 053mm (80.8 in)a/ 2 052 mm (80.8 in)b 1 736 mm (68.4 in)/ 1 729 mm (68.1 in)a,b 1 988 mm (78.3 in)a,b 3 967 mm (156.2 in )a/ 4 379 mm (172.4 in)b 6 242 mm (245.8 in)a/ 6 654 mm (262.0 in)b

F250-Crew Cab Dimension

(1) Overall height

(2) Track (Front / Rear) (3) Overall width (4) Wheelbase

(5) Overall length

aShort wheel base bLong wheel base

F350–except Crew Cab Dimension

Body style

(1) Overall height

(2) Track (Front / Rear)

Chassis Cab 1 972 mm (77.6 in)

Regular Cab 1 860 mm (73.2 in)c,e

1 736.3 mm (68.3 in) / 1 879.6 mm (74.0 in)

1 736.3 mm (68.3 in) / 1 729.3 mm (68.0 in)

(3) Overall width

2 025 mm (79.7 in)

2 031 mm (79.9 in)

Super Cab 4x2
1 865 mm (73.4 in)a 1 861 mm (73.6 in)b 1 736.3 mm (68.3 in) / 1 729.3 mm (68.0 in)a,c 1 736.3 mm (68.3 in) / 1879.6 mm (74.0 in)b,d 2 031 mm (79.9 in)

Super Cab 4x4
1 960 mm (77.2 in)

1 737.3 mm (68.4 in) / 1 729.3 mm (68.0 in)

2 031 mm (79.9 in)

257

Capacities and specifications

Dimension

Body style

Chassis Cab 3 576.3 mm (140.8 in)

Regular Cab 3 479.8 mm (137.0 in)

(4) Wheelbase

(5) Overall length

5 732 mm (225.7 in)

5 754 mm (226.5 in)

Super Cab 4x4
3 601 mm (141.8 in)a/ 4 013.2 mm (158.0 in)b 6 291 mm (247.7 in)

Super Cab 4x2
3 601 mm (141.8 in)a/ 4 013.2 mm (158.0 in)b 5 879 mm (231.4 in)a/ 6 288 mm (247.6 in)b

aShort wheel base bLong wheel base cSingle rear wheels dDual rear wheels

F350-Crew Cab Dimension

(1) Overall height (2) Track (Front / Rear) (3) Overall width (4) Wheelbase

(5) Overall length

aShort wheel base bLong wheel base

258

Body style

Crew Cab 4x2
1 929 mm (75.9 in) 1 745 mm (68.7 in)/ 1 729 mm (68.1 in)a,b 1 988 mm (78.3 in)a,b 3 967 mm (156.2 in )a/4 379 mm (172.4
in)b 6 242 mm (245.8
in)a/6 654 mm (262.0
in)b

Crew Cab 4x4
2 038 mm (80.2 in) 1 736 mm (68.4 in)/ 1 729 mm (68.1 in)a,b 2 077 mm (79.0 in)a,b 3 967 mm (156.2 in )a/4 379 mm (172.4
in)b 6 242 mm (245.8
in)a/6 654 mm (262.0
in)b

F450
Dimension

(1) Overall height (2) Track (Front / Rear)

(3) Overall width (4) Wheelbase (5) Overall length

Capacities and specifications

Chassis Cab 4x2
2 044 mm (80.5 in) 1 736 mm (68.4 in) / 1 610 mm (63.4 in) 2 025 mm (79.7 in) 3 576 mm (140.8 in) 5 732 mm (225.6 in)a 6 341 mm (249.6 in)b

Body style

Chassis Cab 4x4
2 051 mm (80.7 in) 1 736 mm (68.4 in) / 1 610 mm (63.4 in) 2 376 mm (93.5 in) 4 186 mm (164.8 in)

Crew Cab 4x2
2 053 mm (80.8 in) 1 736 mm (68.4 in) / 1 610 mm (63.4 in) 2 376 mm (93.5 in) 4 475 mm (176.2 in)

Crew Cab 4x4
2 056 mm (80.9 in) 1 736 mm (68.4 in) / 1 610 mm (63.4 in) 2 376 mm (93.5 in) 4 475 mm (176.2 in)

5 733 mm (225.7 in)a 6 343 mm (249.7 in)b

5 733 mm (225.7 in)a 6 343 mm (249.7 in)b

5 733 mm (225.7 in)a 6 343 mm (249.7 in)b

aShort wheel base bLong wheel base

F550
Dimension

Body style

Chassis Cab 4x2
2 076 mm (81.7 in) 1 736 mm (68.3 in) / 1 879 mm (74 in) 2 025 mm (79.7 in) 3 576 mm (140.8 in)

Chassis Cab 4x4
2 075 mm (81.6 in) 1 736 mm (68.3 in) / 1 879 mm (74 in) 2 376 mm (93.5 in) 3 576 mm (140.8 in)

Crew Cab 4x2
2 067 mm (81.4 in) 1 736 mm (68.4 in) / 1 610 mm (63.4 in) 2 376 mm (93.5 in) 4 475 mm (176.2 in)

Crew Cab 4x4
2 066 mm (81.3 in) 1 736 mm (68.4 in) / 1 610 mm (63.4 in) 2 376 mm (93.5 in) 4 475 mm (176.2 in)

(1) Overall height (2) Track (Front / Rear)

(3) Overall width (4) Wheelbase

259

Capacities and specifications

Dimension

Body style

(5) Overall length

Chassis Cab 4x2
5 732 mm (225.6 in)a/ 6 341 mm (249.6 in)b

Chassis Cab 4x4

5 733 mm (225.7 in)a/ 6 343 mm (249.7 in)b

Crew Cab 4x2

5 733 mm (225.7 in)a/ 6 343 mm (249.7 in)b

Crew Cab 4x4

5 733 mm (225.7 in)a/ 6 343 mm (249.7 in)b

aShort wheel base bLong wheel base

260

Capacities and specifications

IDENTIFYING YOUR VEHICLE

Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.

261

Capacities and specifications

Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.)

XXXXXXXXXXXXXXXXX

Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).

262

Customer assistance

Ford Extended Service Plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides the following: • Benefits during the warranty period depending on the plan you

purchase (such as: reimbursement for rentals; coverage for certain maintenance and wear items).

• Protection against covered repair costs after your Bumper-to-Bumper

Warranty expires.

You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage. When you buy Ford ESP, you receive Peace-of-Mind protection throughout the United States and Canada, provided by a network of more than 5,000
participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Please contact your dealer for further information. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com.

GETTING THE SERVICES YOU NEED

At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. It is preferred that you return to the Ford dealer where your vehicle was purchased when warranty repairs are needed. However, you may also take your vehicle to another Ford Motor Company or Ford of Canada dealership authorized for warranty repairs. Certain warranty repairs require special training though, so not all dealers are authorized to perform all warranty repairs. That means that depending on the warranty repair needed, the vehicle may need to be taken to another dealer. If a particular dealership can not assist you, then contact the Customer Relationship Center.

263

Customer assistance

If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3. If the inquiry or concern cannot be resolved at the dealership level, please contact the Ford Customer Relationship Center. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P.O. Box 6248
Dearborn, Michigan 48121
1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
1-800-565-3673 (FORD) If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P.O. Box 6248
Dearborn, Michigan 48121
1-800-521-4140
(TDD for the hearing impaired: 1-800-232-5952)

264

Customer assistance

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6J 5E4
1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Relationship Center: