2015 Ford F 150 Owners Manual

•

•

If you are driving more than 15 mi (24 km) at temperatures above freezing, angle the plow blade either full left or full right to provide maximum airflow to the radiator. If you are driving less than 15 mi (24 km) at speeds up to 45 mph (72 km/h) in cold weather, you do not need to worry about blade position to provide maximum airflow.

Transmission Operation while Plowing

WARNING

Do not spin the wheels at over 35
mph (55 km/h). The tires may fail and injure a passenger or bystander.

•

•

Shift transfer case to 4L (4WD Low) when plowing in small areas at speeds below 5.0 mph (8 km/h). Shift transfer case to 4H (4WD High) when plowing larger areas or light snow at higher speeds. Do not exceed 15 mph (24 km/h).

• Do not shift the transmission from a forward gear to R (Reverse) until the engine is at idle and the wheels have stopped.

Outside Air Temperature While Plowing While plowing with your vehicle, the plow blade can block the sensor airflow and cause the outside air temperature reading to be inaccurate. A Ford wiring kit is available to relocate the Outside Air Temperature sensor to the plow blade frame to provide more accurate outside air temperature readings. Contact an authorized dealer for more information.

275

F-150 (TFC), enUSA, Third Printing

Roadside Emergencies

ROADSIDE ASSISTANCE Vehicles Sold in the United States: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • •

24 hours a day, seven days a week. For the coverage period listed on the Roadside Assistance Card included in your Owner's Manual portfolio.

Roadside Assistance covers: • A flat tire change with a good spare, if

provided with the vehicle (except vehicles supplied with a tire inflation kit). Battery jump start. Lock-out assistance (key replacement cost is the customer's responsibility). Fuel delivery — independent service contractors, if not prohibited by state, local or municipal law, shall deliver up to 2 gal (7.6 L) of gasoline or 5 gal (18.9 L) of diesel fuel to a disabled vehicle. Roadside Assistance limits fuel delivery service to two no-charge occurrences within a 12-month period.

• Winch out — available within 100 ft

(30.5 m) of a paved or county maintained road, no recoveries. Towing — independent service contractors, if not prohibited by state, local or municipal law, shall tow Ford eligible vehicles to an authorized dealer within 35 mi (56 km) of the disablement location or to the nearest

• •

•

•

authorized dealer. If a member requests a tow to an authorized dealer that is more than 35 mi (56 km) from the disablement location, the member shall be responsible for any mileage costs in excess of 35 mi (56 km).

Roadside Assistance includes up to $200
for a towed trailer if the disabled eligible vehicle requires service at the nearest authorized dealer. If the towing vehicle is operational but the trailer is not, then the trailer does not qualify for any roadside services. Vehicles Sold in the United States: Using Roadside Assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. This card is in the owner's information portfolio in the glove compartment. United States Ford vehicle customers who require Roadside Assistance, call 1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford Motor Company reimburses a reasonable amount for towing to the nearest dealership within 35 mi (56 km). To obtain reimbursement information, United States Ford vehicle customers call 1-800-241-3673. Customers need to submit their original receipts. Vehicles Sold in Canada: Getting Roadside Assistance Canadian customers who require roadside assistance, call 1-800-665-2006. Vehicles Sold in Canada: Using Roadside Assistance For your convenience, you may complete the roadside assistance identification card found in the centerfold of your warranty guide and retain for future reference.

276

F-150 (TFC), enUSA, Third Printing

Roadside Emergencies

HAZARD WARNING FLASHERS Note: The hazard warning flashers will operate when the ignition is in any position or if the key is not in the ignition. If used when the engine is not running, the battery will lose charge. As a result, there may be insufficient power to restart your engine. The hazard flasher control is located on the instrument panel by the radio. Use it when your

vehicle is disabled and is creating a safety hazard for other motorists. • Press the flasher control and all front

and rear direction indicators flash.

• Press the flasher control again to turn

them off.

FUEL SHUTOFF

WARNING

Failure to inspect and, if necessary, repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision.

In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of fuel to the engine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision, you may restart your vehicle. For vehicles equipped with a key system: 1. Switch off the ignition. 2. Switch on the ignition. 3. Repeat Steps 1 and 2 to re-enable the

fuel pump.

Canadian roadside coverage and benefits may differ from the U.S. coverage. If you require more information, please refer to the coverage section of your warranty guide, call us in Canada at 1-800-665-2006, or visit our website at www.ford.ca. Sykes Assistance Services Corporation administers the Roadside Assistance program. You must receive covered services in Canada or the continental United States. Coverage extends to vehicles that use public, non-seasonal, annually traveled roadways. Roadside Assistance coverage does not extend to vehicles involved in cross-country driving, logging, autocross and any other form of off-road use. Well maintained roads and surfaces help ensure safe travel for the supplier, and allow their representatives to perform service as per the standard operating procedures. In Remote Locations If our supplier cannot take your vehicle by road to the nearest authorized dealership, transportation by rail or water may be necessary. The program covers a tow to the dock or rail terminal and also to the dealership at the end of the trip. For rail or water transportation, however, contact your authorized dealer to confirm if you are eligible for additional coverage before you authorize or pay for the service. Call Ford Roadside Assistance at 1-800-665-2006 for additional information.

277

F-150 (TFC), enUSA, Third Printing

E142663Roadside Emergencies

WARNINGS

Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or

clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.

Use only adequately sized cables with insulated clamps.

Preparing Your Vehicle Do not attempt to push-start your automatic transmission vehicle. Note: Attempting to push-start a vehicle with an automatic transmission may cause transmission damage. Note: Use only a 12-volt supply to start your vehicle. Note: Do not disconnect the battery of the disabled vehicle as this could damage the vehicle electrical system. Park the booster vehicle close to the hood of the disabled vehicle, making sure the two vehicles do not touch. Connecting the Jumper Cables

WARNINGS

Do not attach the cables to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points. Stay clear of moving parts. To avoid reverse polarity connections, make sure that you correctly identify the positive (+) and negative (-) terminals on both the disabled and booster vehicles before connecting the cables.

For vehicles equipped with a push button start system: 1. Press the START/STOP button to

switch off the ignition.

2. Press the brake pedal and press the

START/STOP button to switch on the ignition.

3. Remove your foot from the brake pedal and press the START/STOP button to switch off the ignition.

4. You can either attempt to start the engine by pressing the brake pedal and the START/STOP button, or switch on the ignition only by pressing the START/STOP button without pressing the brake pedal. Both ways re-enable the fuel system.

Note: When you try to restart your vehicle after a fuel shutoff, the vehicle makes sure that various systems are safe to restart. Once your vehicle determines that the systems are safe, then the vehicle will allow you to restart. Note: In the event that your vehicle does not restart after your third attempt, contact an authorized dealer. JUMP STARTING THE VEHICLE

WARNINGS

Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow

flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide correct ventilation.

278

F-150 (TFC), enUSA, Third Printing

Roadside Emergencies

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the booster vehicle battery.

3. Connect the negative (-) cable to the

negative (-) terminal of the booster vehicle battery.

4. Make the final connection of the

negative (-) cable to an exposed metal part of the stalled vehicle's engine, away from the battery and the fuel injection system, or connect the negative (-) cable to a ground connection point if available.

Jump Starting 1. Start the engine of the booster vehicle and rev the engine moderately, or press the accelerator gently to keep your engine speed between 2000 and 3000
RPM, as shown in your tachometer.

2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been

started, run both vehicle engines for an additional three minutes before disconnecting the jumper cables. Removing the Jumper Cables Remove the jumper cables in the reverse order that they were connected.

WARNINGS

Do not attach the end of the positive cable to the studs or L-shaped eyelet located above the positive (+)

terminal of your vehicle’s battery. High current may flow through and cause damage to the fuses.

Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.

A spark may cause an explosion of the gases that surround the battery.

Note: In the illustration, the bottom vehicle represents the booster vehicle.

1. Connect the positive (+) jumper cable

to the positive (+) terminal of the discharged battery.

279

F-150 (TFC), enUSA, Third Printing

4213E142664Roadside Emergencies

POST-CRASH ALERT SYSTEM The system flashes the direction indicators and sounds the horn (intermittently) in the event of a serious impact that deploys an airbag (front, side, side curtain or Safety Canopy) or the safety belt pretensioners. The horn and indicators will turn off when: • •

You press the hazard control button. You press the panic button on the remote entry transmitter (if equipped). Your vehicle runs out of power.

•

280

1. Remove the negative (-) jumper cable

from the disabled vehicle.

2. Remove the jumper cable on the

negative (-) terminal of the booster vehicle battery.

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle battery.

4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle battery.

5. Allow the engine to idle for at least one

minute.

F-150 (TFC), enUSA, Third Printing

4132E142665Customer Assistance

These are some of the items that can be found online: • U.S. dealer locator by Dealer Name,

City/State or Zip Code.

Ford Extended Service Plans. Ford Genuine Accessories. Service specials and promotions.

• Owner Manuals. • Maintenance Schedules. • Recalls. • • • In Canada: Mailing address Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000
Oakville, Ontario L6K 0C8
Telephone 1-800-565-3673 (FORD) Online www.ford.ca Twitter @FordServiceCA (English Canada) @FordServiceQC (Quebec) Additional Assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing authorized dealer. If your inquiry or concern remains unresolved, contact the Sales Manager, Service Manager or Customer Relations Manager. If you require assistance or clarification on Ford Motor Company policies, please contact the Ford Customer Relationship Center.

3.

2.

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorized dealer. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and equipment, so not all authorized dealers are authorized to perform all warranty repairs. This means that, depending on the warranty repair needed, you may have to take your vehicle to another authorized dealer. A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft® parts, or remanufactured or other parts that are authorized by Ford. Away From Home If you are away from home when your vehicle needs service, contact the Ford Customer Relationship Center or use the online resources listed below to find the nearest authorized dealer. In the United States: Mailing address Ford Motor Company Customer Relationship Center P.O. Box 6248
Dearborn, MI 48121
Telephone 1-800-392-3673 (FORD) (TDD for the hearing impaired: 1-800-232-5952) Online Additional information and resources are available online at www.fordowner.com

281

F-150 (TFC), enUSA, Third Printing

Customer Assistance

California Civil Code Section 1793.22(b) presumes that the manufacturer has had a reasonable number of attempts to conform the vehicle to its applicable express warranties if, within the first 18
months of ownership of a new vehicle or the first 18000 miles (29 000 km), whichever occurs first: 1. Two or more repair attempts are made on the same non-conformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR

3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time).

In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126
You are required to submit your warranty dispute to BBB AUTO LINE before asserting in court any rights or remedies conferred by California Civil Code Section 1793.22(b). You are also required to use BBB AUTO LINE before exercising rights or seeking remedies created by the Federal Magnuson-Moss Warranty Act, 15 U.S.C. sec. 2301 et seq. If you choose to seek redress by pursuing rights and remedies not created by California Civil Code Section 1793.22(b) or the Magnuson-Moss Warranty Act, resort to BBB AUTO LINE is not required by those statutes.

•

In order to help us serve you better, please have the following information available when contacting a Customer Relationship Center: • Vehicle Identification Number. •

Your telephone number (home and business). The name of the authorized dealer and city where located. The vehicle’s current odometer reading.

• In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identical or repurchase the vehicle and reimburse the buyer in an amount equal to the actual price paid or payable by the consumer (less a reasonable allowance for consumer use). The consumer has the right to choose whether to receive a refund or replacement vehicle.

282

F-150 (TFC), enUSA, Third Printing

Customer Assistance

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. If a warranty concern has not been resolved using the three-step procedure outlined earlier in this chapter in the Getting the Services you need section, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration. During mediation, a representative of the BBB will contact both you and Ford Motor Company to explore options for settlement of the claim. If an agreement is not reached during mediation or you do not want to participate in mediation, and if your claim is eligible, you may participate in the arbitration process. An arbitration hearing will be scheduled so that you can present your case in an informal setting before an impartial person. The arbitrator will consider the testimony provided and make a decision after the hearing. Disputes submitted to the BBB AUTO LINE program are usually decided within forty days after you file your claim with the BBB. You are not bound by the decision, and may reject the decision and proceed to court where all findings of the BBB Auto Line dispute, and decision, are admissible in the court action. Should you choose to accept the BBB AUTO LINE decision, Ford is then bound by the decision, and must comply with the decision within 30 days of receipt of your acceptance letter. BBB AUTO LINE Application: Using the information provided below, please call or write to request a program application. You will be asked for your name and address, general information about your new vehicle, information about your warranty concerns, and any steps you have

already taken to try to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines. You can get more information by calling BBB AUTO LINE at 1-800-955-5100, or writing to: BBB AUTO LINE 3033 Wilson Boulevard, Suite 600
Arlington, Virginia 22201
BBB AUTO LINE applications can also be requested by calling the Ford Motor Company Customer Relationship Center at 1-800-392-3673. Note: Ford Motor Company reserves the right to change eligibility limitations, modify procedures, or to discontinue this process at any time without notice and without obligation. UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings.

283

F-150 (TFC), enUSA, Third Printing

Customer Assistance

In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment. These impartial arbitrators review the positions of the parties, make decisions and, when appropriate, render awards to resolve disputes. CAMVAP decisions are fast, fair, and final as the arbitrator’s award is binding on both you and Ford of Canada. CAMVAP services are available in all Canadian territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685
or visit www.camvap.ca. GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact our Customer Relationship Center. The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company or Ford of Canada is not responsible for any damage caused by use of improper fuel. Using leaded fuel may also result in difficulty importing your vehicle back into the United States.

If your vehicle must be serviced while you are traveling or living in Asia-Pacific Region, Sub-Saharan Africa, U.S. Virgin Islands, Central America, the Caribbean, and Israel, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (313) 594-4857
Fax: (313) 390-0804
Email: [email protected] For customers in Guam, the Commonwealth of the Northern Mariana Islands (CNMI), America Samoa, and the U.S. Virgin Islands, please feel free to call our Toll-Free Number: (800) 841-FORD (3673). If your vehicle must be serviced while you are traveling or living in Puerto Rico, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Telephone: (800) 841-FORD (3673) FAX: (313) 390-0804
Email: [email protected] www.ford.com.pr If your vehicle must be serviced while you are traveling or living in the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact:

284

F-150 (TFC), enUSA, Third Printing

Customer Assistance

Or to order a free publication catalog, call toll free: 1-800-782-4356
Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www.helminc.com (Items in this catalog may be purchased by credit card, check or money order.) Obtaining a French Owner’s Manual French Owner’s Manual can be obtained from your authorized dealer or by contacting Helm, Incorporated using the contact information listed previously in this section. REPORTING SAFETY DEFECTS (U.S. ONLY)

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.

FORD MOTOR COMPANY Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3
Allen Park, Michigan 48101
U.S.A. Ford: 80004443673
Lincoln: 80004441067
If calling from the UAE: 80004441066
If calling from the Kingdom of Saudi Arabia: 8008443673
If calling from Kuwait: 22280384
FAX: +971 4 3327266
Email: [email protected] www.me.ford.com If you buy your vehicle in North America and then relocate to any of the above locations, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations & Global Growth Initiatives by emailing [email protected]. If you are in another foreign country, contact the nearest authorized dealer. In the event your inquiry is unresolved, communicate your concern with the dealership’s Sales Manager, Service Manager or Customer Relations Manager. If you require additional assistance or clarification, please contact the respective Customer Relationship Center as previously listed. Customers in the U.S. should call 1-800-392-3673. ORDERING ADDITIONAL OWNER'S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATED 47911 Halyard Drive Plymouth, Michigan 48170
Attention: Customer Service

285

F-150 (TFC), enUSA, Third Printing

E142557Customer Assistance

If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator

1200 New Jersey Avenue, Southeast Washington, D.C. 20590
You can also obtain other information about motor vehicle safety from http://www.safercar.gov. REPORTING SAFETY DEFECTS (CANADA ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform Transport Canada.

Transport Canada Contact Information

Website Phone

http://www.tc.gc.ca/eng/roadsafety/menu.htm 1–800–333–0510

286

F-150 (TFC), enUSA, Third Printing

Fuses

FUSE SPECIFICATION CHART Power Distribution Box WARNINGS

Always disconnect the battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the power distribution box before

reconnecting the battery or refilling fluid reservoirs.

The power distribution box is located in the engine compartment. It has high-current fuses that protect your vehicle's main electrical systems from overloads. If you disconnect and reconnect the battery, you will need to reset some features. See Changing the 12V Battery (page 307).

Fuse or relay number

Fuse amp rating

Protected components

— — —

Not used. Not used. Not used.

287

F-150 (TFC), enUSA, Third Printing

E176315Fuses

Fuse or relay number

Fuse amp rating

Protected components

10
11
12
13
14
15
16
17
18
19
20

21A 21B 22
23
24
25
26
27
28

—

40A*

— — — — —

60A* 50A* 60A* 20A** 25A** 10A** 15A** 10A** 10A** 15A**

— —

30A* 15A* 25A*

—

30A* 30A* 30A*

Telescoping side-view mirror. Rear window defroster. Not used. Not used. Telescoping side-view mirror. Not used. Not used. Automatic brake system motor. Body control module 1. Body control module 2. Amplifier. 4x4. Spot light module. Heated seat. Steering-column lock. Power seats. Snow plow. Rear heated seats. Not used. Not used. Windshield wiper motor. Rain sensor. Series fan feed. Not used. Driver seat motors. Passenger power seat. Climate controlled seat.

288

F-150 (TFC), enUSA, Third Printing

Fuses

Fuse or relay number

Fuse amp rating

Protected components

29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54

— — — —

50A* 25A* 20A* 25A* 50A* 10A** 10A** 15A** 10A** 30A** 25A** 10A** 10A** 10A**

— —

30A* 30A*

— — —

30A*

Not used. Air conditioner clutch relay. Not used. Not used. Electric fan 3. Trailer tow park lamps. Trailer tow stop-turn relay fuse. Trailer tow lamps module. Electric fan 1. Alt A sensor. Integrated wheel end solenoid. E-locker. Telescoping mirror. Transmission fluid pump. Horn. Air conditioner clutch. Powertrain control module relay coil. Wiper relay coil. Not used. Not used. Trailer brake control module. Power running boards. Fuel pump relay. Not used. Not used. Voltage quality module. Body-control-module voltage-quality- module feed.

289

F-150 (TFC), enUSA, Third Printing

Fuses

Fuse or relay number

Fuse amp rating

55
56
57
58
59
60
61

62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80

40A* 20A* 30A* 30A* 30A* 40A* 30A*

—

15A**

— — — — — — — —

25A*

—

30A*

— — — — — —

Protected components Body control module RP2 feed. Fuel pump. Right-hand EPB actuator. Left-hand EPB actuator. Starter. Blower motor. Brake control module. Automatic brake system valves. Power seat relay. Heated mirrors. Not used. Starter relay. Powertrain control module relay. Windshield wiper relay. Blower motor relay. Power sliding back window relay. Electric fan 1 relay. Not used. 4x4. Not used. PDRG motor. Horn relay. Not used. Steering column lock relay. Not used. Trailer tow parking lamp relay. Rear window defroster relay.

290

F-150 (TFC), enUSA, Third Printing

Fuses

Fuse or relay number

Fuse amp rating

Protected components

81
82
83
84
85
86
87
88
89
90
91
92
93

94
95
96
97
98
99

100
101
102
103
104
105

— — — — — — 10A* —

20A** 20A** 20A** 20A** 25A** 10A**

—

25A**

—

10A**

—

20A** 15A**

— — — — —

10A**

Not used. PDRG close relay. Not used. Not used. Not used. Not used. Trailer tow backup lamps. Not used. Cigar lighter power point 1. Power point 2. Power point 3. Power point 4. GTDI vehicle power 1. PFI vehicle power 1. Not used. Vehicle power 2. Not used. Vehicle power 3. Not used. Vehicle power 4 (PFI). Vehicle power 4 (GTDI). Not used. Not used. Snow plow relay. Not used. Electic fan 3 relay. Power steering.

291

F-150 (TFC), enUSA, Third Printing

Fuses

Fuse or relay number

Fuse amp rating

Protected components

106
107
108
109
110

111
112
113

114
115
116

—

10A**

—

10A** 10A**

10A**

—

7.5A**

— — —

Not used. Anti-lock brakes. Not used. Powertrain control module. 4x4 run/start. Adaptive cruise control. Transmission pump run-start. Not used. Blind spot information system. Rear view camera. Front view camera. Voltage quality module. Electric fan 2 relay. Not used. Not used.

*Cartridge fuses **Mini fuses

Passenger Compartment Fuse Panel The fuse panel is in the right-hand side of the passenger footwell behind a trim panel. To remove the trim panel, pull it toward you and swing it away from the side. To reinstall it, line up the tabs with the grooves on the panel, and then push it shut.

To remove the fuse panel cover, press in the tabs on both sides of the cover, and then pull it off. To reinstall the fuse panel cover, place the top part of the cover on the fuse panel and push the bottom part until it latches. Gently pull on the cover to make sure it has latched properly.

292

F-150 (TFC), enUSA, Third Printing

Fuses

Fuse or relay number

Fuse amp rating

Protected components

F-150 (TFC), enUSA, Third Printing

10A

7.5A

20A 5A 20A 10A 10A 10A 10A

Demand lamp relay. Power seats relay. Glove box. Vanity lamps. Overhead console. Dome. Courtesy. Map lamps. Memory module logic. Memory seat switches. Lumbar motor. Driver door lock motor. Trailer brake control. Not used. Not used. Not used. Not used. Not used.

293

E145984Fuses

Fuse or relay number

Fuse amp rating

Protected components

10
11
12

13

14
15
16
17
18

19

20
21

22

23

24
25
26
27

28
29

5A 5A 7.5A

7.5A

10A 10A 15A 5A 5A

7.5A

7.5A 5A

5A

10A

20A 30A 30A 30A

20A 30A

Not used (spare). Combined sensor module. Climate head module. Smart datalink converter. Cluster. SCCM. Brake. Smart datalink converter. Tailgate release. HUD. Ignition switch and passive-entry passive- start start stop switch. Key inhibit solenoid. Tow haul (O/D) cancel for floor or column shifter. Not used. HUD. In car temperature with humidity sensor. EPB. Power seat. PDRG switch. Inverter. Driver side window. Moonroof. Central lock/unlock. Driver door control module. Passenger door control module. Vista roof. Moonroof. Not used. Not used.

294

F-150 (TFC), enUSA, Third Printing

Fuses

Fuse or relay number

Fuse amp rating

Protected components

30
31
32

33
34
35
36

37
38

30A 15A 10A

20A 30A 5A 15A

15A

30A Circuit breaker.

CHANGING A FUSE Fuses

WARNING

You must replace a failed fuse with one that has the specified amperage rating. If you use a fuse with a higher

amperage rating, you may cause severe wire damage and may start a fire.

Not used. Adjustable pedal switch and motor. Multi-function display. Global position system. Sync 1. Sync 2. Radio frequency receiver. Radio. Run-start relay. Restraints module. 360 camera module. Heated steering wheel module. Rear-view mirror. Rear heated seats. Power distribution box run-start relay. Rear window switches and motors.

A fuse may fail if electrical components in the vehicle are not properly working. A broken wire inside the fuse indicates a failed fuse. Check the appropriate fuses before replacing any electrical components.

295

F-150 (TFC), enUSA, Third Printing

E142430Maintenance

Working with the Engine Off 1. Set the parking brake and shift to park

(P).

2. Switch off the engine. 3. Block the wheels. Working with the Engine On

WARNING

To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner

removed and do not remove it while the engine is running.

1. Set the parking brake and shift to park

(P).

2. Block the wheels OPENING AND CLOSING THE HOOD 1.

Inside the vehicle, pull the hood release handle located under the left hand side of the instrument panel.

GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of authorized dealers that are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly. They are supported by a wide range of highly specialized tools developed specifically for servicing your vehicle. To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. See Scheduled Maintenance (page 498). If your vehicle requires professional service, an authorized dealer can provide the necessary parts and service. Check your warranty information to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Motorcraft® parts are designed and built to provide the best performance in your vehicle. Precautions • Do not work on a hot engine. • Make sure that nothing gets caught in

moving parts.

• Do not work on a vehicle with the

engine running in an enclosed space, unless you are sure you have enough ventilation. Keep all open flames and other burning material (such as cigarettes) away from the battery and all fuel related parts.

•

296

F-150 (TFC), enUSA, Third Printing

2. Go to the front of your vehicle and locate the secondary release lever under the front of the hood near the center of your vehicle.

E166491Maintenance

3. Raise the hood until the lift cylinders

hold it open.

4. To close, lower the hood and make

sure that it is closed properly and fully latched.

UNDER HOOD OVERVIEW - 2.7L ECOBOOST™ 2.7L EcoBoost

297

F-150 (TFC), enUSA, Third Printing

E190266E176046Maintenance

A. B. C. D. E. F. G. H.

Power distribution box. See Fuses (page 287). Battery. See Changing the 12V Battery (page 307). Engine oil filler cap. See Engine Oil Check (page 301). Engine oil dipstick. See Engine Oil Dipstick (page 301). Brake fluid reservoir. See Brake Fluid Check (page 307). Air filter assembly. See Changing the Engine Air Filter (page 317). Engine coolant reservoir. See Engine Coolant Check (page 302). Windshield washer fluid reservoir. See Washer Fluid Check (page 307).

UNDER HOOD OVERVIEW - 3.5L ECOBOOST™

A. B. C.

Windshield washer fluid reservoir. See Washer Fluid Check (page 307). Battery. See Changing the 12V Battery (page 307). Engine oil filler cap. See Engine Oil Check (page 301).

298

F-150 (TFC), enUSA, Third Printing

AABDEFCGHE166496Maintenance

D. E. F. G. H.

Engine oil dipstick. See Engine Oil Dipstick (page 301). Brake fluid reservoir. See Brake Fluid Check (page 307). Engine coolant reservoir. See Engine Coolant Check (page 302). Air filter assembly. See Changing the Engine Air Filter (page 317). Power distribution box. See Fuses (page 287).

UNDER HOOD OVERVIEW - 3.5L

A. B. C. D. E. F.

Power distribution box. See Fuses (page 287). Battery. See Changing the 12V Battery (page 307). Engine oil filler cap. See Engine Oil Check (page 301). Engine oil dipstick. See Engine Oil Dipstick (page 301). Brake fluid reservoir. See Brake Fluid Check (page 307). Air filter assembly. See Changing the Engine Air Filter (page 317).

299

F-150 (TFC), enUSA, Third Printing

E176214Maintenance

G. H.

Engine coolant reservoir. See Engine Coolant Check (page 302). Windshield washer fluid reservoir. See Washer Fluid Check (page 307).

UNDER HOOD OVERVIEW - 5.0L

A. B. C. D. E. F. G. H.

Windshield washer fluid reservoir. See Washer Fluid Check (page 307). Battery. See Changing the 12V Battery (page 307). Engine oil filler cap. See Engine Oil Check (page 301). Engine oil dipstick. See Engine Oil Dipstick (page 301). Brake fluid reservoir. See Brake Fluid Check (page 307). Engine coolant reservoir. See Engine Coolant Check (page 302). Air filter assembly. See Changing the Engine Air Filter (page 317). Power distribution box. See Fuses (page 287).

300

F-150 (TFC), enUSA, Third Printing

E166494AAABACADAEAFAAAGAAAHMaintenance

6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. •

If the oil level is between the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. If the oil level is below the lower hole, add enough oil to raise the level within the lower and upper holes.

•

• Oil levels above the upper hole may

cause engine damage. Some oil must be removed from the engine by an authorized dealer.

7. Put the oil level dipstick back into the oil dipstick tube and ensure it is fully seated.

Adding Engine Oil Note: Do not remove the filler cap when the engine is running. Note: Do not remove the engine oil level dipstick when the engine is running. Note: Do not add oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage.

ENGINE OIL DIPSTICK

MIN MAX

ENGINE OIL CHECK 1. Make sure that your vehicle is on level

ground.

2. Switch the engine off and wait 15

minutes for the oil to drain into the oil pan.

3. Set the parking brake and ensure the

gearshift is in park (P).

4. Open the hood. Protect yourself from

engine heat.

5. Locate and carefully remove the engine

oil level dipstick. See Under Hood Overview (page 299).

301

F-150 (TFC), enUSA, Third Printing

E161560ABE142732Maintenance

WARNINGS

To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure. Steam and hot liquid can come out forcefully when you loosen the cap slightly.

Do not add coolant further than the MAX mark.

Checking the Engine Coolant When the engine is cold, check the concentration and level of the engine coolant at the intervals listed in the scheduled maintenance information. See Scheduled Maintenance (page 498). Note: Make sure that the coolant level is between the MIN and MAX marks on the coolant reservoir. Note: Coolant expands when it is hot. The level may extend beyond the MAX mark. Note: If the level is at the MIN mark, below the MIN mark, or empty, add coolant immediately. Maintain coolant concentration within 48% to 50%, which equates to a freeze point between -30°F (-34°C) and -34°F (-37°C). Note: For best results, coolant concentration should be tested with a refractometer such as Robinair® Coolant and Battery Refractometer 75240. We do not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations. Note: Automotive fluids are not interchangeable. Do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location.

Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricants Specification Advisory Council (ILSAC), comprised of U.S. and Japanese automobile manufacturers. 1. Check the engine oil level. 2.

If the engine oil level is not within the normal range, add engine oil that meets Ford specifications. See Capacities and Specifications (page 358).

3. Remove the engine oil filler cap and

use a funnel to pour the engine oil into the opening.

4. Wipe off any spilled oil. 5. Recheck the engine oil level. Make sure

the oil level is not above the normal operating range on the engine oil level dipstick. Install the engine oil level dipstick and ensure it is fully seated.

6.

7. Fully install the engine oil filler cap by

turning the filler cap clockwise until three clicks are heard or until the cap is fully seated.

ENGINE COOLANT CHECK

WARNINGS

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, spilling coolant on hot engine parts can burn you.

Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine

coolant could make it difficult to see through the windshield.

302

F-150 (TFC), enUSA, Third Printing

Maintenance

Brine.

• • Any engine coolant mixed with alcohol

or methanol antifreeze or coolant.

Alcohol and other liquids can cause engine damage from overheating or freezing. Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the engine coolant. When adding coolant: 1. Unscrew the cap slowly. Any pressure

will escape as you unscrew the cap.

2. Add prediluted engine coolant meeting the Ford specification. See Capacities and Specifications (page 358).

3. Check the coolant level in the coolant reservoir the next few times you drive your vehicle. If necessary, add enough prediluted engine coolant to bring the coolant level to the proper level.

4.

Recycled Engine Coolant Ford Motor Company does not recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.

Adding Engine Coolant Note: Do not use stop leak pellets, cooling system sealants or additives as they can cause damage to the engine cooling or heating systems. Your warranty may not cover these damages. Note: During normal vehicle operation, the coolant may change color from orange to pink or light red. As long as the coolant is clear and uncontaminated, this color change does not indicate the coolant has degraded nor does it require the coolant to be drained, the system to be flushed, or the coolant to be replaced. Do not mix different colors or types of coolant in your vehicle. Mixing of engine coolants may harm your engine’s cooling system. The use of an improper coolant may harm engine and cooling system components and may void the warranty. Use prediluted engine coolant meeting the Ford specification. See Capacities and Specifications (page 358). In case of emergency, you can add a large amount of water without engine coolant in order to reach a vehicle service location. In this instance, qualified personnel: 1. Must drain the cooling system. 2. Chemically clean the cooling system

with Motorcraft Premium Cooling System Flush.

3. Refill with engine coolant as soon as

possible.

Water alone, without engine coolant, can cause engine damage from corrosion, overheating or freezing. Do not use the following as a coolant substitute: • Alcohol. • Methanol.

303

F-150 (TFC), enUSA, Third Printing

Maintenance

the service engine soon indicator will illuminate. If the engine reaches a preset over-temperature condition, the engine automatically switches to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs, your vehicle will still operate. However: • •

The engine power will be limited. This will disable the air conditioning system.

Continued operation increases the engine temperature, causing the engine to completely shut down. Your steering and braking effort increases in this situation. When the engine temperature cools, you can re-start your engine. Take your vehicle to an authorized dealer as soon as possible to minimize engine damage. When Fail-Safe Mode Is Activated

WARNINGS

Fail-safe mode is for use during emergencies only. Operate your vehicle in fail-safe mode only as long as necessary to bring your vehicle to rest in a safe location and seek immediate repairs. When in fail-safe mode, your vehicle will have limited power, will not be able to maintain high-speed operation, and may completely shut down without warning, potentially losing engine power, power steering assist, and power brake assist, which may increase the possibility of a crash resulting in serious injury.

Never remove the coolant reservoir cap while the engine is running or hot.

Severe Climates If you drive in extremely cold climates: • It may be necessary to have a Ford authorized dealer increase the coolant concentration above 50%.

• A coolant concentration of 60%

provides improved freeze point protection. Engine coolant concentrations above 60% decrease the overheat protection characteristics of the engine coolant and may cause engine damage.

If you drive in extremely hot climates: It may be necessary to have a Ford • authorized dealer decrease the coolant concentration to 40%.

• A coolant concentration of 40%

provides improved overheat protection. Engine coolant concentrations below 40% decrease the freeze and corrosion protection characteristics of the engine coolant and may cause engine damage.

Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection. What You Should Know About Fail- Safe Cooling If you deplete the engine coolant supply, fail-safe cooling allows you to temporarily drive your vehicle before you incur incremental component damage. The fail-safe distance depends on ambient temperatures, vehicle load and terrain. How Fail-Safe Cooling Works If the engine begins to overheat, the engine coolant temperature gauge will move to the red (hot) area and:

the coolant temperature warning light will illuminate

304

F-150 (TFC), enUSA, Third Printing

Maintenance

At this time, you may notice your engine coolant temperature gauge needle move toward the H and the POWER REDUCED TO LOWER TEMP message may appear in the information display. You may notice a reduction in vehicle speed caused by reduced engine power. In order to manage the engine fluid temperatures, your vehicle may enter this mode if certain high-temperature and high-load conditions take place. The amount of speed reduction depends on many factors such as vehicle loading, towing, grade and ambient temperature. If this occurs, there is no need to pull off the road. You can continue to drive your vehicle while this message is active. The air conditioning may also cycle on and off during severe operating conditions to protect overheating of the engine. When the engine coolant temperature decreases to a normal operating temperature, the air conditioning will turn on once again. If the engine coolant temperature gauge moves fully into the red (hot) area, or if the coolant temperature warning or service engine soon messages appear in your information display: 1. Pull off the road as soon as safely

possible and shift the transmission into P.

2. Leave the engine running until the coolant temperature gauge needle moves away from the red (hot) area. After several minutes, if the temperature does not drop, follow the remaining steps.

3. Switch the engine off and wait for it to cool before checking the coolant level. If the coolant level is normal, restart your engine and continue.

4.

You have limited engine power when in the fail-safe mode, so drive your vehicle with caution. Your vehicle will not maintain high-speed operation and the engine will operate poorly. Remember that the engine is capable of automatically shutting down to prevent engine damage. In this situation: 1. Pull off the road as soon as safely possible and switch off the engine. 2. Tow your vehicle to an authorized

3.

dealer. If this is not possible, wait a short period for the engine to cool.

4. Check the coolant level and add if low. 5. Re-start the engine and drive your

vehicle to an authorized dealer.

Note: Driving your vehicle without repair increases the chance of engine damage. Contact an authorized dealer as soon as possible. Engine Fluid Temperature Management (If Equipped)

WARNINGS

To reduce the risk of crash and injury, be prepared that the vehicle speed may reduce and the vehicle may not be able to accelerate with full power until the fluid temperatures reduce.

Never remove the coolant reservoir cap while the engine is running or hot.

Your vehicle can pull a trailer, but because of the added load, your vehicle’s engine may temporarily reach higher temperatures during severe operating conditions such as ascending a long or steep grade while pulling a trailer in high temperatures.

305

F-150 (TFC), enUSA, Third Printing

Maintenance

TRANSFER CASE FLUID CHECK

1. Clean the area around the filler plug. 2. Remove the filler plug. 3.

Inspect the fluid level. The fluid level should be within 0.20 in (5mm) from the bottom of the hole.

4. Add fluid through the filler opening. Fill

to the bottom of the opening.

Use only fluid that meets Ford specifications. See Capacities and Specifications (page 358).

5.

If the coolant is low, add coolant, and restart the engine. See Adding Engine Coolant or How Fail-Safe Cooling Works in this chapter for more information.

AUTOMATIC TRANSMISSION FLUID CHECK If required, have an authorized dealer check and change the transmission fluid at the correct service interval. See Scheduled Maintenance (page 498). The automatic transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, if the transmission slips, shifts slowly or if you notice a sign of leaking fluid, contact an authorized dealer. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components.

306

F-150 (TFC), enUSA, Third Printing

E170444Maintenance

FUEL FILTER Your vehicle is equipped with a lifetime fuel filter that is integrated with the fuel tank. Regular maintenance or replacement is not needed. CHANGING THE 12V BATTERY

WARNINGS

Batteries normally produce explosive gases that can cause personal injury. Therefore, do not allow flames,

sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.

This vehicle may be equipped with more than one battery, removal of cable from only one battery does not disconnect your vehicle electrical system. Be sure to disconnect cables from all batteries when disconnecting power. Failure to do so may cause serious personal injury or property damage.

When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and damage to the vehicle or battery. Lift the battery with a battery carrier or with your