2003 Ford Explorer Sport TRAC Owners Manual

mirror. When the mirror detects bright light from front or behind, it will adjust automatically to minimize glare. The mirror will automatically return to the normal position whenever the vehicle is placed in R (Reverse) (when the mirror is in the ON position). This helps to ensure a bright clear view in the mirror when backing up.

AUTOLAMP

DELAY

MAX.

OFF

to adjust the left to adjust the right

Power side view mirrors (if equipped) To adjust your mirrors 1. Select mirror or mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to disable the adjust function.

48

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space, like an automatic car wash.

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 48 km/h (30 mph) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 48 km/h (30 mph).

Do not use the speed control in heavy traffic or

on roads that are winding, slippery or unpaved.

Setting speed control

The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.

49

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

3. Press the SET ACC control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator light SPEED CONT instrument cluster will turn on.

on the

steep hill.

Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 16 km/h (10 mph) below

may want to apply the brakes to reduce the speed.

your set speed on an uphill, your speed control will disengage.

Resuming a set speed Press the RSM (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RSM control will not work if the vehicle speed is not faster than 48 km/h (30 mph).

Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET ACC control until you get to the desired speed, then release the control. You can also use the SET ACC control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1.6 km/h (1 mph).

• Use the accelerator pedal to get to the desired speed. When the

vehicle reaches that speed, press and release the SET ACC control.

50

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the COAST control until you get to the desired speed, then release the control. You can also use the COAST control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1.6 km/h (1 mph).

• Depress the brake pedal until the desired vehicle speed is reached, press the SET ACC control.

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will • Press the speed control OFF

not erase your vehicle’s previously set speed.

control.

Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console.

Do not let children play with the moon roof. They may seriously hurt themselves.

51

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

control again.

control. To stop the

control until the glass

To open the moon roof: the moon roof is equipped with a one-touch open feature. Press and release the one-touch open feature press the To close the moon roof: press and hold the panel stops moving. When fully closed, the rear portion of the glass panel will appear higher than the front portion. To vent the moon roof: press and hold the control. The moon roof must be in the closed position in order to move it into the vent position. To close, press and hold the control until the glass panel stops moving. The moon roof sliding shade can be opened or closed manually. The glass panel must be closed in order to move the sliding shade. Note: If the battery is disconnected, discharged, or a new battery is installed, the moon roof positions will need to be reset. To reset the moon roof positions, move the moon roof into the vent position.

OPEN

ELECTRONIC COMPASS AND OUTSIDE TEMPERATURE DISPLAY (IF EQUIPPED) This display provides the outside temperature in °C (Centigrade) or °F (Fahrenheit) and one of the eight compass headings to indicate the direction the vehicle is facing. Outside temperature display Press the MODE control to turn on the display. Press the MODE control again to change from °C to °F. Press the MODE control again to turn off the display. If the outside temperature drops below 4° C (38° F) the word “ICE” will flash in the display alternately with the outside temperature for approximately one minute.

73° NW

GARAGE

MODE

LAMP

LAMP

52

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Electronic compass As an orientation aid, the compass direction abbreviations are displayed here. If you suspect that the compass is not operating correctly, it can be recalibrated. Note: The compass reading may be affected when driving near large buildings, bridges, power lines and broadcast antennas. Magnetic or metallic objects place on or in the vehicle may also affect the compass reading. • Adjusting the compass Note: The ignition must be in the ON position. 1. Press and hold the MODE control until “VAR” appears in the display. The current location number should be displayed.

LAMP

MODE

LAMP

9 VAR

2. Press the MODE control repeatedly until your desired location number appears in the display. Use this zone map to determine which location number you should be using.

23

15

14
13
12

• Adjusting the calibration of the compass Note: To adjust the calibration find an open area free from steel structures and high voltage lines.

7 8 9 1011

53

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

1. Press and hold the MODE control until “CAL” appears in the display then release the control. 2. Drive slowly (less than 5 km/h [3 mph]) in circles until “CAL” disappears from the display (approximately 2 or 3 circles).

POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelets are over the pointed end of the retention posts and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.

LAMP

MODE

LAMP

CAL

TAILGATE LOCK The tailgate lock is designed to prevent theft of the tailgate. • Insert ignition key and turn to the • Turn ignition key to the left to

right to lock.

unlock.

54

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

TAILGATE REMOVAL Your tailgate is removable to allow more room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry the spring clip (on each connector) past the head of the support screw. Disconnect the cables. 3. Lift tailgate to a 45 degree angle and remove it from the left and right hinges. To install, follow the removal procedures in reverse order.

EXTERIOR TIEDOWN HOOKS Exterior tiedown hooks mounted on the side of the pickup box: • can be used to secure loads • can be used to secure half the

within the pickup box.

tonneau cover in an open position.

• allow for continued use of the

stake pockets.

Each tiedown hook can secure loads of up to 350 kg (770 lbs.) inside the pickup box (total load not to exceed box payload of 1000kg (2,200 lbs)). Loads can be secured to the hooks with up to three wraps of 10 mm rope.

CARGO CAGE (IF EQUIPPED) Your vehicle may be equipped with a cargo cage designed to extend the pickup box for larger loads.

55

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

To extend the cargo cage: 1. Lower tailgate. 2. Pull the round knobs on each side of the cargo cage to release it from the pickup box. Red markings behind the knobs indicate the unlocked position. 3. Lift the cargo cage over on to the tailgate. 4. Evenly push down on the cargo cage and push the round knobs in on each side locking it in place. To stow the cargo cage, follow steps one through four in reverse order. The cargo cage may be used to secure a load of up to 46 kg (100
lbs.) on the tailgate. The cargo cage should always be kept in the stowed position with the tailgate closed when not in use. Activating Cargo Cage Theft Deterrent Device: The following procedure can be done with the cargo cage in the stowed or extended position. 1. Locate the phillips head screw in the middle of the vertical brace on the locking clip. 2. Turn the screw counterclockwise until you hear an audible click. 3. To deactivate, turn the screw clockwise until the locking clip moves freely.

56

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

To remove the cargo cage: 1. Extend the cargo cage. 2. Pull the round knobs on each side of the cage to unlock it. Make sure the locking clip screws are loose before removing the cargo cage. 3. Press the locking clips below the middle bar and lift the cargo cage out of the channels on the “D” pillar. To install the cargo cage, follow the removal procedure in reverse order.

TONNEAU COVER (IF EQUIPPED) The tonneau cover has been designed to maximize fuel economy and should be fully installed whenever possible. The rear panel can be folded in half and secured behind the cab, or the whole cover can be removed completely from the vehicle. To avoid damage to the cover, do not operate the vehicle unless the cover is fully installed, or securely stowed. To avoid damage to the cover, do not stand, sit or load anything on top of the cover. To open the front panel: • Open the driver side lock cover • Lift the panel to access items in • To close, lower the panel down

the pickup box near the cab.

and unlock the front panel.

on the pickup box.

The panel will automatically lock when lowered onto the pickup box. Do not drive with front panel unlocked or folded on top of the rear panel.

57

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

the rear panel.

To open the rear panel: • Open the lock cover and unlock • Lift the rear panel to access items • To close, lower the rear panel on

in the pickup box.

the pickup box.

The panel will automatically lock when lowered onto the pickup box. To stow the rear panel: • Before driving with the rear panel • Lift the rear panel up, lay it on top of the front panel and secure it with the two straps to the exterior tiedowns on the pickup box.

open, unlock the rear panel.

Failure to secure the rear panel could damage the tonneau cover or vehicle. To remove the tonneau cover: The tonneau cover weighs 29 kg (70
lbs.) and needs to be supported during removal since the panels will automatically lock when set down on the pickup box. This is a two person operation. • Unlock and support the front and • Fold the rear panel on top of the • Pull the release levers on the underside of the tonnneau cover from

rear panels.

front panel.

the pickup box and remove the cover.

For installation of the tonneau cover, reverse the removal procedure.

58

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Interior tonneau cover release Your vehicle is equipped with a mechanical interior tonneau cover release handle that provides a means of escape for children and adults in the event they become locked inside the pickup box. Adults are advised to familiarize themselves with the operation and location of the release handle. To open the tonneau cover from the inside, pull the “T” shaped handle and push up on the tonneau cover panel. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light. The “T” shaped handle is located on the tonneau cover panel.

Keep vehicle doors and tonneau cover locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children

could lock themselves in the box and risk injury. Children should be taught not to play in vehicles.

On hot days, the temperature in the pickup box can rise very quickly. Exposure of people or animals to these high

temperatures for even a short time can cause death or serious heat-related injuries, including brain damage. Small children are particularly at risk.

LUGGAGE RACK Your vehicle is equipped with a roof rack with out cross bars. The maximum recommended load is 44kg (100 lbs), evenly distributed. If it is not possible to distribute the load, position it as far rearward as possible. Use the tiedown loops to secure the load.

Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as

slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.

59

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Driver Controls

Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a

lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sport cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles. Failure to drive cautiously could result in an increase risk of loss of vehicle control, vehicle rollover, personal injury and death.

60

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

Locks and Security

KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLock娂 Passive Anti-Theft System for more information.

POWER DOOR LOCKS The power door lock controls are located on the driver and front passenger door panels. Pressing the doors. Pressing the the doors.

will unlock all the will lock all

Childproof door locks • When these locks are set, the

rear doors cannot be opened from the inside.

• The rear doors can be opened

from the outside when the doors are unlocked.

The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Move lock control up to engage • Move control down to disengage

the childproof lock.

childproof locks.

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

61

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Your vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without • lock all the vehicle doors without • activate the personal alarm.

a key.

a key.

If there is any potential remote keyless entry problem with your vehicle, ensure ALL remote entry transmitters are taken to the dealership, to aid in troubleshooting.

and release again within three seconds to unlock all the

and release to unlock the driver’s door. Note: The interior

Unlocking the doors 1. Press lamps will illuminate. 2. Press doors. The remote entry system activates the illuminated entry feature. This feature turns on the interior lamps for 25 seconds or until the ignition is turned to the ON position. If the dome lamp control is in the off position the illuminated entry feature will not work. The inside lights will not turn off if: • they have been turned on using the dimmer control or • any door is open. The battery saver feature will turn off the interior lamps 30 minutes after the ignition is turned to the OFF position.

Locking the doors and release to lock all the doors. Note: the interior lamps 1. Press will turn off (unless the dome lamp control is in the full-up position), and the headlamps and parking lamps will flash.

62

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

and release again within three seconds to confirm that all the

2. Press doors are closed and locked. Note: the doors will lock again, the horn will chirp once and the headlamps and parking lamps will flash. If any of the doors are not properly closed the horn will make two quick chirps.

to activate the alarm. The horn will sound for a maximum of

Sounding a panic alarm Press 30 seconds and the parklamps will flash for a maximum of 3 minutes. Press again or turn the ignition to ON to deactivate, or wait for the alarm to timeout in 3 minutes. Note: The panic alarm will only operate when the ignition is in the OFF or ACC position.

Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. The typical operating range for your remote entry transmitter is approximately 10 meters (33 feet). A decrease in the operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle and • other vehicles parked next to the vehicle. To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE REMOTE ENTRY TRANSMITTER APART. 2. Remove the old battery. 3. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. 4. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

63

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. To reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 2 (LOCK) position to 3 (OFF). 4. Cycle, eight times, rapidly (within 10 seconds) between the 3 (OFF) position and 4 (ON). Note: The eighth turn must end in the 4 (ON) position. 5. The doors will lock, then unlock, to confirm that the programming mode has been activated. 6. Within 20 seconds press any button on the remote entry transmitter. Note: If more than 20 seconds have passed you will need to start the procedure over again. 7. The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed. 8. Repeat Step 6 to program each additional remote entry transmitter. 9. Turn the ignition to the 3 (OFF) position after you have finished programming all of the remote entry transmitters. Note: After 20
seconds have passed, you will automatically exit the programming mode. 10. The doors will lock, then unlock, to confirm that the programming mode has been exited.

64

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to: • lock or unlock the doors without • activate or deactivate the

using a key.

autolock feature.

The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5–digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation. Programming a personal entry code To create your own personal entry code: 1. Enter the factory set code. 2. Within five seconds press the 1 • 2 on the keypad. 3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other. Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal • If you set a second personal code it will erase your first personal code. Erasing personal code 1. Enter the factory set 5–digit code. 2. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing step 1. 3. Press the 7 • 8 and the 9 • 0 at the same time. This must be done within five seconds of completing step 2. Your personal code is now erased and only the factory set 5–digit code will work. Anti-scan feature If the wrong code has been entered 36 times, the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash during this time.

code.

65

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

control on the remote entry transmitter.

The anti-scan feature will turn off after: • one minute of keypad inactivity. • pressing the UNLOCK • the ignition is turned to the ON position. Unlocking and locking the doors using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. The interior lamps will illuminate after pressing the first control on the keypad. To unlock all doors, press the 3 • 4 control within five seconds. To lock all doors, press the 7 • 8 and the 9 • 0 at the same time. You do not need to enter the keypad code first. Note: The interior lamps will turn off.

and

Autolock (if equipped) This feature will automatically lock all the doors when: • all the doors are closed, • the ignition key is in the ON position, • the gearshift lever is shifted into, then out of, R (reverse) and then • the brake pedal is released. This feature will also automatically relock all the doors when: • the ignition is in the ON position and any door is opened then closed, • you put the vehicle in motion by releasing the brake pedal. Deactivating/reactivating the autolock feature The autolock feature can be deactivated/reactivated using the following two methods: • keyless entry keypad, or • ignition lock cylinder and interior power door locks control. To deactivate/reactivate the autolock feature using the keypad Your vehicle comes with the autolock feature activated. To deactivate/reactivate this feature: 1. Turn the ignition to the OFF position.

66

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

2. Close all the doors. 3. Enter the 5-digit entry code. 4. Press and hold the 3 • 4. While holding the 3 • 4, press the 7 • 8
within five seconds. 5. Within 5 seconds of Step 4, release the 3 • 4. 6. Within 5 seconds of Step 5, Release the 7 • 8. The horn will chirp once when the system has been successfully deactivated. The horn will chirp twice (one short and one long chirp) when the system has been successfully reactivated. To deactivate/reactivate the autolock feature using the ignition lock cylinder and interior power door locks control 1. Close all the doors. 2. Ensure that the ignition lock cylinder is in the OFF position. 3. Note: Steps 4 through 8 must be carried out within 30 seconds. Turn the ignition lock cylinder from OFF to RUN. 4. Press the power door locks UNLOCK control three times. 5. Turn the ignition lock cylinder from RUN to OFF. 6. Press the power door locks UNLOCK control three times. 7. Turn the ignition lock cylinder from OFF to RUN. 8. Ensure that the vehicle’s horn chirps. This chirp indicates that the feature is in an enable/disable mode and ready to accept program changes. 9. Press the power door locks UNLOCK control once, then the LOCK control once, in order to toggle the autolock feature. 10. Ensure that the horn chirps once; there should only be one horn chirp, indicating that the autolock feature has been deactivated. If one chirp is heard, followed by a longer sound of the horn, the autolock feature has been reactivated. 11. Turn the ignition lock cylinder to the OFF position, or wait two minutes, in order to exit the enable/disable mode. 12. Exit the vehicle and ensure that the horn chirps once to indicate that a feature has been changed and that the autolock feature has been toggled.

67

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to prevent the engine from being started unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condition. Your vehicle comes with two coded keys; additional coded keys may be purchased from your dealer. The dealer can program your spare keys to your vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. You need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key, but may cause a momentary issue if they are too close to the key when starting the engine. If a problem occurs, turn the ignition off, remove all objects on the key chain away from the coded key and restart the engine.

Theft indicator The theft indicator is located in the instrument cluster. • When the ignition is in the OFF position, the indicator will flash once every 2 seconds to indicate the SecuriLock娂 system is functioning as a theft deterrent. • When the ignition is in the ON position, the indicator will glow for 3

seconds, then turn off, to indicate normal system functionality.

If a problem occurs with the SecuriLock娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the ON position. If this occurs, the vehicle should be taken to an authorized dealer for service.

68

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Automatic arming The vehicle is armed immediately after switching the ignition to the 3
(OFF) position. The THEFT indicator will flash every two seconds when the vehicle is armed.

Locks and Security

Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle. • The THEFT indicator will illuminate for three seconds and then go • If the THEFT indicator stays on for an extended period of time or

out.

flashes rapidly, have the system serviced by your dealer.

Replacement keys If your keys are lost or stolen and you don’t have an extra coded key, you will need to have your vehicle towed to a dealership. The key codes need to be erased from your vehicle and new coded keys will need to be programmed. Replacing coded keys can be very costly. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. Please visit an authorized dealer to purchase additional spare or replacement keys.

Programming spare keys You can program your own coded keys to your vehicle. Please read and understand the entire procedure before you begin. Tips: • A maximum of eight keys can be coded to your vehicle. • Only use Securilock娂 keys. • You must have two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible.

69

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Locks and Security • If no previously programmed coded keys are available, you must take

your vehicle to your dealer to have the spare key(s) programmed.

1. Insert a previously programmed coded key into the ignition. 2. Turn the ignition from the 3
(OFF) position to the 4 (ON) position. Keep the ignition in the 4
(ON) position for at least one second, but no more than 10
seconds. 3. Turn the ignition to the 3 (OFF) position, and remove the coded key from the ignition. 4. Within ten seconds of removing the previously programmed coded key, insert the other previously programmed coded key into the ignition. 5. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second but not more than 10 seconds. 6. Turn the ignition to the 3 (OFF) position, and remove the second key from the ignition. 7. Within twenty seconds of removing the previously programmed coded key, insert the unprogrammed key (new/valet key) into the ignition. 8. Turn the ignition from the 3 (OFF) position to the 4 (ON) position. Keep the ignition in the 4 (ON) position for at least one second. 9. Your new unprogrammed key is now programmed. If the key has been successfully programmed it will start the vehicle’s engine and the theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’s engine and the theft indicator light will flash on and off rapidly. If failure repeats, bring your vehicle to your dealer to have the new key(s) programmed. To program additional new unprogrammed key(s), repeat this procedure from step 1 for each additional key.

70

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Seating and Safety Restraints

FRONT SEATS Notes:

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Do not pile cargo higher than the seatbacks to avoid injury in a collision or sudden stop.

Adjustable head restraints (if equipped) Head restraints help to limit head motion in the event of a rear collision. The seats in your vehicle may have adjustable head restraints. Adjust your head restraint so that it is located directly or as close as possible behind your head. To adjust the head restraint: • Raise the head restraint by

pulling it upward.

To lower the head restraint: • Push the release control. • Push down on the head restraint.

71

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Adjusting the front manual seat Pull the lever located at the front edge of the seat to move the seat forward or backward. Release the lever to lock the seat in place.

Adjusting the front power seat (if equipped) The control is located on the outboard side of the seat cushion. Press to raise or lower the front portion of the seat cushion.

Press to raise or lower the rear portion of the seat cushion.

Press the control to move the seat forward, backward, up or down.

72

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Reclining the seats Pull the lever located on the outside of the seat to recline the seatback. Release the lever to lock the seatback in place.

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Never adjust the driver’s seat or seatback when the vehicle is moving.

Power lumbar (if equipped) Push the button forward to inflate, or rearward to deflate.

Heated seats (if equipped) To operate the heated seats: • Push control to activate. • Push again to deactivate.

The indicator light on the control will illuminate when activated.

73

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

REAR SEATS

Adjustable rear head restraints Lift the head restraint so that it is located directly or as close as possible behind your head. Push or pull the head restraint to the desired position.

Folding down rear 60/40 seats 1. Raise the rear seat head restraint.

2. Flip the bottom of the head restraint up, toward the front seat.

74

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

3. While holding the head restraint in a “flat” position, lower the head restraint to the seat back.

4. Flip the seat release control toward the front seat.

5. The seat will automatically fall forward. For Adrenalin vehicles, the 40 percent rear seat (behind the driver) does not fold due to the subwoofer location. See Attaching child safety seats with tether straps in this chapter for tether access behind this seat.

75

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

A carpeted panel will flip down from the back panel to complete the load floor.

Returning the rear 60/40 seats to upright position 1. Push down seatback release control and pull seatback up and into upright position making sure seatback locks into place.

2. Pull head restraint up and return to upright position.

SAFETY RESTRAINTS

Safety restraints precautions

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

To reduce the risk of injury, make sure children sit where they can be properly restrained.

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from

injury in a collision.

76

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is

provided.

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas

are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt.

Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that

are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.

Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check

seat covers and buckles before you place a child anywhere near them.

Energy Management Feature • This vehicle has a safety belt system with an energy management

feature at the front seating positions to help further reduce the risk of injury in the event of a head-on collision. • The front outboard safety belt system has a retractor assembly that is designed to extend the seat belt webbing in a controlled manner. This helps reduce the belt force acting on the user’s chest.

77

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly automatic locking retractor feature or

any other safety belt function is not operating properly when checked according to the procedures in Workshop Manual. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.

2. To unfasten, push the release button and remove the tongue from the buckle.

The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.

78

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Automatic locking mode

How to use the automatic locking mode • Buckle the combination lap and

shoulder belt.

• Grasp the shoulder portion and pull downward until the entire belt is extracted.

• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. When you hear the clicking sound, the safety belt is now in the automatic locking mode.

How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.

After any vehicle collision, the safety belt systems at all outboard seating positions (except the driver position, which doesn’t have

this feature) must be checked by a qualified technician to verify that the automatic locking retractor feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.

79

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.

In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. This mode should be used any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter.

Front safety belt height adjustment Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To adjust the shoulder belt height, push the button and slide the height adjuster up or down. Release the button and pull down on the height adjuster to make sure it is locked in place.

Position the safety belt height adjusters so that the

belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision.

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and right front passenger seating positions.

80

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

The safety belt pretensioner removes some slack from the safety belt system at the start of a crash. The safety belt pretensioner uses the same crash sensor system as the front airbags and Safety Canopy娂 system. When the safety belt pretensioner deploys, the lap and shoulder belt are tightened. When the Safety Canopy娂 system and/or the front airbags are activated, the safety belt pretensioners for the driver and right front passenger seating positions will be activated when the respective seatbelt is properly buckled.

The driver and the right front passenger seat belt system (including retractors, buckles and height adjusters) must be

replaced if the vehicle is involved in a collision that results in deployment of front air bags or Safety Canopy娂 and safety belt pretensioners.

Refer to the Safety belt maintenance section in this chapter.

Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.

Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position...

Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.

The safety belt warning light and warning chime turn off.

The safety belt warning light and indicator chime remain off.

81

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Then... The BeltMinder feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30
seconds, repeating for approximately 5 minutes or until safety belt is buckled. The BeltMinder feature is re-activated.

BeltMinder The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster. If... The driver’s safety belt is not buckled before the vehicle has reached at least 5 km/h (3 mph) and 1-2 minutes have elapsed since the ignition switch has been turned to ON... The driver’s safety belt is buckled for 20 seconds or longer... The driver’s safety belt is buckled while the safety belt indicator light is illuminated and the safety belt warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data)

The BeltMinder feature will not activate.

The BeltMinder feature will not activate.

82

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Reasons given... “Crashes are rare events”

“I’m not going far”

“Belts are uncomfortable”

“I was in a hurry”

“Seat belts don’t work”

“Traffic is light”

“Belts wrinkle my clothes”

“The people I’m with don’t wear belts”

Seating and Safety Restraints

Consider... 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. 3 of 4 fatal crashes occur within 25
miles of home. We design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. Prime time for an accident. BeltMinder reminds us to take a few seconds to buckle up. Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. Nearly 1 of 2 deaths occur in single-vehicle crashes, many when no other vehicles are around. Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. Set the example, teen deaths occur 4
times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see.

83

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Reasons given... “I have an air bag”

“I’d rather be thrown clear”

Consider... Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”.

Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of

injury in an accident. To disable (one-time) or deactivate the Belt Minder feature please follow the directions stated below.

One time disable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, BeltMinder will be disabled for that ignition cycle only. Deactivating/activating the BeltMinder feature (driver’s side) Read steps 1 - 4 thoroughly before proceeding with the deactivation/activation programming procedure. The BeltMinder feature can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set • The gearshift is in P (Park) (automatic transmission) • The ignition switch is in the OFF position • The driver and passenger safety belt is unbuckled

To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle.

1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE) 2. Wait until the safety belt warning light turns off. (Approximately 1
minute)

84

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

• Step 3 must be completed within 50 seconds after the safety belt

warning light turns off.

3. Buckle then unbuckle the safety belt on the driver’s side 9 times, ending in the unbuckled state. (Step 3 must be completed within 50
seconds after the safety belt warning light turns off.) • After step 3, the restraint system warning light (airbag light) will be

turned on for three seconds.

4. Within 10 seconds of the light turning on, buckle then unbuckle the safety belt once. • This will disable the BeltMinder feature if it is currently enabled. As confirmation, the restraint system warning light will flash 4 times per second for 3 seconds. • This will enable the BeltMinder feature if it is currently disabled. As confirmation, the restraint system warning light will flash 4 times per second for 3 seconds, followed by 3 seconds with the light off, then followed by the restraint system warning light flashing 4 times per second for 3 seconds again.

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm (8
inch) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended.

Do not use extensions to change the fit of the shoulder belt across the torso.

Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged (nicks, tears or cuts). Replace parts as necessary. All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if equipped), child safety seat tether bracket assemblies (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after

85

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

a collision. Ford Motor Company recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.

Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe

personal injuries in the event of a collision.

Refer to Interior in the Cleaning chapter.

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

RPMx1000

40

60 70
0 0 0

50

80

100

120

0 0 0 0 0 0

60

30

40

20

20

10 MPH

80

140

90
001

160

180

101

km/h

201

CHECK GAGE

CHECK ENGINE

FUEL DOOR

FUEL RESET

ABS

OFF

ON

OFF

CHECK SUSP

SPEED CONT

4WD HIGH

4WD LOW

O/D OFF

O V E R D R I V E

4X4
HIGH

2WD

4X4
LOW

RSM

SET

ACCEL

COAST

SHUF

SCAN

TUNE

SEEK

REW

FF

DSP

MUTE

EJ

LOAD

PUSH ON

CD

BASS

BAL

SEL

TREB

FADE

MENU

A/C

MAX A/C

Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity. This information will assist Ford Motor Company in servicing the vehicle and in helping to better understand real world collisions and further improve the safety of future vehicles.

The front passenger air bag is not designed to offer protection to an occupant in the center front seating position.

86

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly; there is a risk of injury from a deploying air bag.

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is

provided.

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints.

National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches)

between an occupant’s chest and the air bag module.

Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries.

To properly position yourself away from the air bag: • Move your seat to the rear as far as you can while still reaching the • Recline the seat slightly one or two degrees from the upright position.

pedals comfortably.

Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those

objects to be propelled by the air bag into your face and torso causing serious injury.

87

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or

Lincoln Mercury dealer.

Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure and tow

hooks) may affect the performance of the air bag system, increasing the risk of injury. Do not modify the front end of the vehicle.

Children and air bags Children must always be properly restrained; accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a collision.

Air bags can kill or injure a child in a child seat.

NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back.

88

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains a longitudinal deceleration sufficient to cause the air bag sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not sufficient enough to cause activation. Air bags are designed to inflate in frontal and near-frontal collisions, not rollover, side-impact, or rear-impacts unless the collision causes sufficient longitudinal deceleration. The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic. While the SRS is designed to help reduce serious injuries, contact with a deploying air bag may also cause abrasions, swelling or temporary hearing loss. Because air bags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. It is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control. The SRS consists of: • driver and passenger air bag modules (which include the inflators and • one or more impact and safing sensors

air bags)

89

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints • a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components

Several air bag system components get hot after inflation. Do not touch them after inflation.

If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not

replaced, the unrepaired area will increase the risk of injury in a collision.

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the status of the system. Refer to Air bag readiness section in the Instrument cluster chapter. Routine maintenance of the air bag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light will either • The readiness light will not illuminate immediately after ignition is turned on.

• A series of five beeps will be heard. The tone pattern will repeat

flash or stay lit.

periodically until the problem and/or light are repaired.

If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision.

90

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

SAFETY CANOPY姟 SYSTEM (IF EQUIPPED)

Do not place objects or mount equipment on or

near the headliner at the siderail that may come into contact with a deploying Safety Canopy娂. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.

Do not lean your head on the door. The Safety Canopy娂 could injure you as it deploys from the headliner.

Do not attempt to service, repair, or modify the Safety Canopy娂 system, its fuses, the A, B, or C pillar trim, or the headliner on a

vehicle containing a Safety Canopy娂. See your Ford or Lincoln Mercury dealer.

All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS and Safety

Canopy娂 system is provided.

To reduce risk of injury, do not obstruct or place objects in the deployment path of the inflatable Safety Canopy娂.

91

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

How does the Safety Canopy姟 system work? The design and development of the Safety Canopy娂 system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Air Bag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety Canopy娂). The Safety Canopy娂 system consists of the following: • An inflatable nylon curtain with a gas generator concealed behind the headliner and above the doors (one on each side of vehicle). • A headliner designed to flex open • The same warning light, electronic control and diagnostic unit as used • Two crash sensors mounted in the b-pillars (one on each side). • Two crash sensors located at the c-pillar (one on each side). • Rollover sensor in the restraints control module (RCM). The Safety Canopy娂 system, in combination with seat belts, can help reduce the risk of severe injuries in the event of a significant side impact collision or rollover event. Children 12 years old and under should always be properly restrained in the second or third row seats. The Safety Canopy娂 will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening. The Safety Canopy娂 system is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the side crash sensor to close an electrical circuit that initiates Safety Canopy娂 inflation or when a certain likelihood of a rollover event is detected by the rollover sensor. The Safety Canopy娂 is mounted to roof side-rail sheet metal, behind the headliner, above the first and second row seats. In certain lateral

above the side doors to allow Safety Canopy娂 deployment.

for the front airbags.

92

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

collisions or rollover events, the Safety Canopy娂 system will be activated on both sides of the vehicle, regardless of which seats are occupied. The Safety Canopy娂 is designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events. The fact that the Safety Canopy娂 did not activate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. The Safety Canopy娂 is designed to inflate in certain side impact collisions or rollover events, not in rear impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration or rollover likelihood.

Several Safety Canopy娂 system components get hot after inflation. Do not touch them after inflation.

If the Safety Canopy娂 system has deployed, the

Safety Canopy娂 will not function again unless replaced. The Safety Canopy娂 system (including the A, B and C pillar trim) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the Safety Canopy娂 is not replaced, the unrepaired area will increase the risk of injury in a collision.

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Air bag readiness section in the Instrument Cluster chapter. Routine maintenance of the air bag is not required.

93

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

flash or stay lit.

Any difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front air bag system) will either • The readiness light will not illuminate immediately after ignition is • A series of five beeps will be heard. The tone pattern will repeat

turned on.

periodically until the problem and light are repaired.

If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision or rollover event.

Disposal of air bags and air bag equipped vehicles (including pretensioners) See your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel.

SAFETY RESTRAINTS FOR CHILDREN Read the following sections for directions on how to properly use safety restraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about air bags.

Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less) ride in your vehicle, you must put them in safety seats made especially for children. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle. When possible, always place children under age 12 in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from

injury in a collision.

Always follow the instructions and warnings that come with any infant or child restraint you might use.

94

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle.

Do not leave children, unreliable adults, or pets unattended in your vehicle.

To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labeled as conforming to all applicable Federal motor vehicle safety standards. Belt-positioning booster seats raise the child and provide a shorter, firmer seating cushion that encourages safer seating posture and better fit of lap and shoulder belts on the child. A belt-positioning booster seat should be used if the shoulder belt rests in front of the child’s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion. You may wish to discuss the special needs of your child with your pediatrician.

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 pounds and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly, which could increase the risk of serious injury. To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably. Booster seats also make the shoulder belt fit better and more comfortably for growing children. When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly. Generally this is when they weigh about 80 lbs (about 8 to 12 years old).

95

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching?

• Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless.

If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top of ear level) above the top of the seat. In this case, move the backless booster to another seating position with a higher seat back and lap/shoulder belts.

• Those with a high back.

If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice.

Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs.

96

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

The shoulder belt should cross the chest, resting snugly on the center of the shoulder. The lap belt should rest low and snug across the hips, never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition. The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only. It is best to use a booster seat with lap/shoulder belts in the back seat- the safest place for children to ride.

Follow all instructions provided by the manufacturer of the booster seat.

Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of

the body and may increase the risk of injury or death in a collision.

Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a

collision.

SAFETY SEATS FOR CHILDREN

Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the

97

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System (SRS) section in this chapter. • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from).

• Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. • Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic

locking mode (passenger side front and outboard rear seating positions) (if equipped) section in this chapter.

Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching child safety seats with tether straps in this chapter.

Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.

98

2003 P207 Explorer Sport Trac (p27) Owners Guide (post-2002-fmt) USA English (fus)

Seating and Safety Restraints

Installing child safety seats in combination lap and shoulder belt seating positions

Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must

use a forward-facing child seat in the front seat, move the seat all the way back.

Children 12 and under should be properly restrained in the rear