2006 Ford Expedition Owners Manual

counterclockwise and remove from the lamp assembly. 7. Carefully pull the bulb out of the socket and push in the new bulb. 8. Install the bulb socket into the lamp assembly and rotate clockwise. 9. Replace the lamp assembly and install all three retainer bolts on the lamp assembly. Replacing tail/stop/turn/sidemarker/backup lamp bulbs The tail/stop/turn/sidemarker/backup lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Make sure the headlamp switch is in the OFF position and then open the liftgate to expose the lamp assembly screws. 2. Remove the two screws from the lamp assembly. 3. Carefully remove the lamp assembly away from the vehicle by pulling the assembly straight out to expose the bulb socket. DO NOT TIP THE LAMP ASSEMBLY SIDEWAYS.

101

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Lights

4. Rotate the bulb socket counterclockwise and remove from lamp assembly. 5. Pull bulb straight out of socket and snap in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. 7. Carefully install the tail lamp assembly on the vehicle by securing the lamp assembly with two screws.

High-mount brakelamp To change the high-mount brakelamp bulbs: 1. Remove the two screws holding the lamp assembly in place.

2. Pull the lamp assembly straight out. 3. Remove the wire harness. 4. Depress the four tabs that hold the light assembly on, one at a time, and pull the black bulb carrier away from the lamp. 5. Pull the old bulb out and replace with the new bulb. 6. Snap the black bulb carrier into the lamp assembly. 7. Replace the wire harness. 8. Replace the lamp assembly.

102

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Lights

Replacing foglamp bulbs

Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

1. Make sure the headlamp switch is in the OFF position and the engine is not running. 2. Remove the bulb socket from the foglamp by turning counterclockwise. 3. Disconnect the electrical connector from the foglamp bulb. 4. Connect the new foglamp bulb to the electrical connector. 5. Install the bulb socket in the foglamp turning clockwise.

Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assembly on the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the license lamp screw from the assembly. 3. Pull the lamp down and twist the bulb socket counterclockwise. Remove the bulb socket from the lamp. 4. Pull out the old bulb and push in the new bulb. 5. Install the bulb socket in the lamp assembly by turning it clockwise. 6. Install the lamp assembly and secure it with the retaining screw.

103

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Lights

Approach lamp/mirror turn signal bulb removal (if equipped) To change the bulbs: 1. Make sure the headlamp switch is in the OFF position and then fold the mirror forward. 2. Remove the torx screw on the bottom of the turn signal lens using a T-10 torx driver. 3. Pull the turn signal lens down to remove it from the mirror assembly. 4. Disconnect the bulb assembly from the lens. 5. Remove and replace the bulb. 6. Reverse the order to reassemble lamp and lens.

Approach lamp bulb removal (if equipped) To change the bulbs: 1. Make sure that all the doors are closed and the interior lights have automatically turned off or the opposite mirror approach lamp has turned off. 2. With a small flat tipped screwdriver, insert the tip into the approach light module slot located on the outboard corner of the lens to release the clip. 3. While holding the clip in the release position, pull the approach light module down. 4. Remove the two wires from the module and replace the module with a new one. 5. Reverse the order to reassemble the approach light module.

104

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

OFF

I N T 2
I N T 1
OFF

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Speed dependent wipers: When the wiper control is on, the speed of the wipers will automatically adjust with the vehicle speed. The faster your vehicle is travelling the faster the wipers will go. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three times with washer • a long push and hold: the wipers and washer fluid will be activated for

fluid.

I N T 2
I N T 1
OFF

OFF

up to ten seconds.

Rear window wiper/washer controls For rear wiper operation, rotate the rear window wiper and washer control to the desired position. Select: INT 2 — Normal speed operation of rear wiper. INT 1 — Intermittent operation of rear wiper. OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) the rear wiper/washer control to either From either position, the control will automatically return to the INT 2
or OFF position.

position.

I N T 2
I N T 1
OFF

OFF

105

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

TILT STEERING Push the lever down to unlock the steering column. While the lever is in the down position, tilt the steering column to the desired position.

While holding the steering wheel, pull the lever up to its original position to lock the steering column.

Never adjust the steering column when the vehicle is

moving.

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp.

106

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Slide on rod feature (if equipped) Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield.

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according to your option package.

Forward storage bin and conversation mirror (if equipped) The storage compartment may be used to store two pairs of sunglasses or similar objects. Press the release control to open the storage compartment. The door will open slightly and can be moved to full open.

The conversation mirror on the cover allows the driver to view the rear seating area.

This does not replace the rear view mirror.

107

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Power quarter rear windows (if equipped) • Without a moon roof

• With a moon roof

Press the quarter windows. Press the quarter windows.

portion of the VENT control to open the power rear

portion of the VENT control to close the power rear

Do not leave children unattended in the vehicle and do not let children play with the power rear quarter windows. They may

seriously injure themselves.

When closing the power rear quarter windows, you should verify that it is free of obstructions and ensure that children and/or

pets are not in the proximity of the window opening.

108

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

CENTER CONSOLE (IF EQUIPPED) The center console offers several useful storage features. These include: 1. Pen holder 2. Tissue holder 3. Large utility compartment 4. PalmPilot娂/PDA holder 5. Cupholders 6. Coin holder slots 7. Small utility compartment 8. Three power points

Use only soft cups in the cupholder. Hard objects can

injure you in a collision.

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Always keep the power point caps closed when not being used.

109

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

The third auxiliary power point on the center console is accessible from the rear seats.

The rear auxiliary power point is located on the right rear quarter panel. The power point is accessible from the liftgate or the third row seat. Equipped with rear climate control

Not equipped with rear climate control

Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty.

110

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

POWER WINDOWS (IF EQUIPPED)

Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure

themselves.

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in

the proximity of the window openings.

Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window.

One touch down Allows the driver’s window to open fully without holding the control down. Press completely down on the bottom part of the rocker switch and release quickly. Press the rocker switch again to stop.

Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls. Accessory delay With accessory delay, the window switches, audio system and moon roof (if equipped) may be used for up to ten minutes after the ignition switch is turned to the OFF position or until either front door is opened.

111

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may be equipped with an inside rear view mirror with an auto-dimming function. The electrochromic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare. The mirror will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up. Do not block the sensor on the backside of the inside rear view mirror since this may impair proper mirror performance.

EXTERIOR MIRRORS

Power side view mirrors The ignition can be in any position to adjust the power side view mirrors. To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place.

112

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Powerfold mirrors (if equipped) Rotate the 4–way adjustment switch to the center position. Press the switch down to auto fold in and down again to auto fold back to design position. Powerfold the side mirrors in carefully when driving through a narrow space, like an automatic car wash. The mirrors may be moved inward/outward manually, however, if a mirror is moved manually, it will need to be reset. To reset: with the switch in the center position, press the switch down to fold the mirrors in and wait a short period (8
seconds). An audible ⬙click⬙ will be heard indicating re-synchronization. If the click is not heard, use the switch to fold the mirrors out, then in, until the click is heard. After that, the mirrors will operate to their normal positions until they are again moved manually.

(if equipped)

Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

113

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Signal indicator mirrors (if equipped) When the turn signal is activated, the lower portion of the mirror housing will blink.

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal. • Press the bottom of the control to • Press the top of the control to adjust the pedals away from you. The adjustment allows for approximately 3 inches (76 mm) of maximum travel.

adjust the pedals toward you.

Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.

SPEED CONTROL With speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h).

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

114

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.

3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator light instrument cluster will turn on.

on the

RES

SET

COAST

steep hill.

Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below

may want to apply the brakes to reduce the speed.

your set speed on an uphill, your speed control will disengage.

115

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h).

RES

SET

COAST

Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).

RES

SET

COAST

• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.

116

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

RES

SET

Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the COAST/CST control until you get to the desired speed, then release the control. You can also use the COAST/CST control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).

COAST

• Depress the brake pedal until the desired vehicle speed is reached, press the SET + control.

RES

SET

COAST

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’s previously • Press the speed control OFF

set speed.

control.

Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

117

Driver Controls

STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features.

Audio control features to select: Press • AM, FM1, FM2, • CD, or • DVD (if equipped).

In AM, FM1, or FM2 mode: • Press MEM to select preset

stations within the selected radio band.

In CD mode: • Press MEM to select the next

selection on the CD.

In any mode: • Press VOL + or − to adjust

volume.

118

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Climate control features Press TMP + or - to adjust temperature.

Press

+ or - to adjust fan speed.

MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console.

Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.

Note: The moon roof will open to the “comfort” position first before opening all the way. The “comfort” position helps to alleviate rumbling wind noise which may happen in the vehicle with the roof fully opened.

119

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

control again.

control. The moon roof

To open the moon roof: The moon roof is equipped with a one-touch open feature. Press and release the will open to the “comfort” position. Press and release the control again to fully open. To stop the one-touch open feature press either the or To close the moon roof: Press and control until the glass stops moving. When fully closed, the hold the rear portion of the glass panel will appear higher than the front portion. To vent the moon roof: Press and hold the control. The moon roof must be in the closed position in order to move it into the vent position. To close, press and hold the panel stops moving. The moon roof has a built-in sliding shade that can be manually opened or closed when the glass panel is shut. To close the shade, pull it toward the front of the vehicle.

control until the glass

When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the

proximity of the moon roof opening.

HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.

When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of

the way to prevent potential harm or damage.

120

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.

Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the ACC position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal. 1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat Step 1
to program additional hand-held transmitters to the remaining two HomeLink威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink威. 2. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your visor) while keeping the indicator light in view.

121

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

3. Simultaneously press and hold both the HomeLink威 and hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator and Canadian Programming” in this section for Canadian residents. 4. The indicator light will flash slowly and then rapidly. Release both buttons when the indicator light flashes rapidly. (The rapid flashing light indicates acceptance of the hand-held transmitters’ radio frequency signals.) 5. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the light is constant, programming is complete and your device should activate when the HomeLink威 button is pressed and released. Note: To program the remaining two HomeLink威 buttons, begin with Step 2 in the “Programming” section — do not repeat Step 1. Note: If the indicator light blinks rapidly for two seconds and then turns to a continuous red, proceed with Steps 6 through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with Step 2 in the “Programming” section. For questions or comments, please contact HomeLink at www.homelink.com or 1–800–355–3515.

122

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Steps 1 and 2
outlined in the “Programming” section, replace Step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink威 button (note Step 3 in the

“Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.

• Proceed with Step 4 in the “Programming” section.

Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.

123

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.

HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 2 in the “Programming” section. Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink威 button, follow Step 2 in the “Programming” section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515. ELECTRONIC COMPASS/TEMPERATURE DISPLAY WITHOUT MESSAGE CENTER (IF EQUIPPED) Outside air temperature In vehicles without Dual Electronic Automatic Temperature Control (DATC), the outside temperature display is contained in the instrument cluster and displays all the time. In vehicles with DATC, the temperature displays in the climate control display. To turn the display off or change the display from English to Metric see your dealer. Compass The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antennas. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy.

124

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass calibration adjustment in this section. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone adjustment in this section. Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Turn ignition to the ON position. 3. Start the engine.

23

15

14
13
12

7 8 9 1011

4. Locate the reset button on the compass sensor mounted on the base of mirror. 5. Press and hold for six seconds and release. You will see that ZONE appears in the instrument cluster display. 6. Press and release the button until the desired zone number appears. Note: The range of zone values are from 01 to 15 and “wraps” back to 01. 7. The zone will be stored, and the cluster display will return to the ⬙normal⬙ mode when the button has not been pressed for 4 seconds. Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.

125

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. Start the vehicle. 2. Locate the reset button on the compass sensor mounted on the base of mirror. 3. To enter the compass calibration mode, press and hold the button for greater than eight seconds. The display will then show CAL in the display window. 4. Drive the vehicle slowly (less than 3 mph [5 km/h]) in circles until CAL indicator turns off. As many as 5 complete circles may be required. 5. The compass is now calibrated.

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime.

Selectable features

Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu.

126

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Info menu This control displays the following control displays: • Odometer/Compass • Trip odometer/Odometer/Compass • Distance to Empty • Average Fuel Economy • Trip Elapsed Drive Time • Outside air temperature Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Compass display The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone/calibration adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone/calibration adjustment.

127

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Compass zone/calibration adjustment 1. Determine your magnetic zone by referring to the zone map. 2. Turn ignition to the ON position. 3. Start the engine. 4. From Info menu, select the Compass/Odometer function. (Do not select Trip, DTE, or AFE. The top of the message center must be blank).

23

5. Press and hold the RESET until the message center displays a selection to change the current zone setting.

15

14
13
12

7 8 9 1011

6. Press and release the RESET control until the message center display changes to show the current zone setting (XX). 7. Press and release the SETUP control repeatedly until the correct zone setting for your geographic location is displayed on the message center. The range of zone values are from 1 to 15 and “wraps” back to 1. 8. To exit the zone setting mode, and to “lock in” your change, press and release the RESET control.

Perform compass calibration in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 9. Press the RESET control to start the compass calibration function. 10. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CIRCLE SLOWLY TO

128

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

CALIBRATE display changes to CALIBRATION COMPLETE. It will take up to five circles to complete calibration. 11. The compass is now calibrated.

Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have approximately 50 miles (80 km) to empty. If you RESET this warning message, this display and tone will return within 10 minutes. DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected. Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/ 100 km. If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic shut-off points on the fuel pumps at • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter)

service stations

129

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control (press and hold RESET for 2
Seconds in order to reset the function) after setting the speed control to get accurate highway fuel economy readings. Trip elapsed drive time Select this function from the INFO menu to display a timer. To operate the Trip Elapsed Drive Time perform the following: 1. Press and release RESET in order to start the timer. 2. Press and release RESET to pause the timer. 3. Press and hold RESET for 2 seconds in order to reset the timer. Outside air temperature (if equipped) Press and hold the INFO button for 2 seconds to display the outside temperature. To switch from a blank display to the temperature display, hold the INFO button for 2 seconds until the temperature is seen in the display. To switch the temperature display to compass display, hold the INFO button again for 2 seconds until the compass heading is seen in the display To turn the display off or change the display from English to metric see your authorized dealer. Setup menu Press this control for the following displays: • System Check • Units (English/Metric) • Autolock • Easy Exit Seat • Autolamp Delay • Language

130

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Autolocks This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion. 1. To disable/enable the autolock feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the autolock ON or OFF. Easy exit seat (if equipped) This feature automatically moves the drivers seat backwards for easy exit from the vehicle. 1. To disable/enable the easy exit seat feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the easy entry exit seat ON or OFF. Autolamp delay This feature keeps your headlights on for up to three minutes after the ignition is switched off. 1. To disable/enable the autolamp delay feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to select the new Autolamp delay values of >0, >10, >20, >30, >60, >90, >120 or >180. Reverse Sensing System (if equipped) This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected. 1. To disable/enable the reverse sensing system feature, put the vehicle in R (Reverse). 2. Press the RESET control to turn the park assist ON or OFF.

131

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Language 1. Select this function from the SETUP menu for the current language to be displayed.

2. Pressing the RESET control cycles the message center through each of the language choices.

3. Press and hold the RESET control to set the language choice.

Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric.

System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds. Pressing the RESET control cycles the message center through each of the systems being monitored. The sequence of the system check report and how it appears in the message center is as follows: 1. DOOR STATUS 2. ENGINE TEMP 3. CHARGING SYSTEM

132

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

4. OIL PRESSURE 5. BRAKE FLUID LEVEL 6. TIRE PRESSURE SYSTEM (if equipped) 7. ADVANCETRAC威 with RSC (if equipped) 8. AIR SUSPENSION SYSTEM (if equipped) 9. WASHER FLUID LEVEL 10. FUEL LEVEL 11. DTE System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages that have been reset are divided into three categories: • They cannot be cleared until the condition is corrected. • They will reappear on the display ten minutes from the reset. • They will not reappear until an ignition OFF-ON cycle has been

completed.

This acts as a reminder that these warning conditions still exist within the vehicle.

133

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Warning display Park assist ON/OFF (if equipped) Warning displays when R (reverse)

Status

gear is selected. Warning returns after 10 minutes

Warning returns after the ignition key is turned from OFF to ON.

Liftgate or liftglass ajar Low fuel level Check charging system Low brake fluid level Low oil pressure Check engine temperature Check AdvTrac (if equipped) Temporary 4X4 high Low tire pressure (if equipped) Tire pressure monitor fault (if equipped) Tire pressure sensor fault (if equipped) Check park assist (if equipped) Low washer fluid level Check air suspension (if equipped) Air suspension switched OFF (if equipped) Check compass module Compass no response Check fuel cap Door ajar Reduced engine power Stop engine safely Check electronic throttle control or engine fail safe mode Park brake engaged PARK ASSIST ON/OFF (if equipped). Displayed when the transmission is in R (Reverse) and the Reverse Sensing System is disabled. Refer to Reverse Sensing System in this section to enable.

Will not clear until condition is corrected

134

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

CHECK PARK ASSIST (if equipped). Displayed when the transmission is in R (Reverse) and the Reverse Sensing System is disabled. Refer to Reverse Sensing System in this section to enable. ADVTRAC ON (if equipped). Displayed when the AdvanceTrac威 with RSC is ON. ADVTRAC OFF (if equipped). Displayed when the AdvanceTrac威 with RSC is OFF. DOOR AJAR. Displayed when a door is not completely closed. LIFTGATE OR LIFTGLASS AJAR. Displayed when the liftgate or liftgate glass is not completely closed. CHECK ENGINE TEMPERATURE. Displayed when the engine coolant is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as safely possible. REDUCED ENGINE POWER. Displayed when the engine is overheating. Stop the vehicle as soon as safely possible, turn off the engine. If the warning stays on or continues to come on, contact your authorized dealer as soon as safely possible. CHECK ELECTRONIC THROTTLE CONTROL or ENGINE FAIL SAFE MODE. Displayed when the engine has defaulted to a “limp-home” operation. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. STOP ENGINE SAFELY. Displayed when the engine is overheating. Stop the vehicle as soon as safely possible, turn off the engine. If the warning stays on or continues to come on, contact your authorized dealer as soon as safely possible. LOW TIRE PRESSURE (if equipped).Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. TIRE PRESSURE MONITOR FAULT (if equipped). Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, have the system inspected by your authorized dealer.

135

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

TIRE PRESSURE SENSOR FAULT (if equipped). Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. LOW FUEL LEVEL. Displayed as an early reminder of a low fuel condition. CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible. PARK BRAKE ENGAGED. Displayed when the park brake is engaged. If the warning stays on after the park brake is off, contact your authorized dealer as soon as possible. LOW BRAKE FLUID LEVEL. Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid reservoir in the Maintenance and Specifications chapter. LOW OIL PRESSURE. Displayed when the engine oil pressure is low. If this warning message is displayed, check the level of the engine oil. Refer to Engine oil in the Maintenance and Specifications chapter for information about adding engine oil. If the oil level is OK and this warning persists, shut down the engine immediately and contact your authorized dealer for service. LOW WASHER FLUID LEVEL. Indicates the washer fluid reservoir is less than one quarter full. Check the washer fluid level. Refer to Windshield washer fluid in the Maintenance and Specifications chapter. CHECK ADVTRAC (if equipped). Displayed when the AdvanceTrac威 with RSC system is not operating properly. If this message is displayed on the message center the AdvanceTrac威 with RSC system may be partially operable. If this warning stays on while the engine is running, contact your authorized dealer for service as soon as possible. For further information, refer to AdvanceTrac威 with RSC stability enhancement system in the Driving chapter.

136

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

ADVTRAC OFF T/C ON with RSC (if equipped). Displayed on 4x4
vehicles only when 4x4 Low Range is selected. In this mode, the stability enhancement portion of the AdvanceTrac威 with RSC is disabled, but the traction enhancement feature remains enabled. For further information, refer to AdvanceTrac威 with RSC stability enhancement system in the Driving chapter. TEMPORARY 4X4 HIGH. Displayed when the 4X4 system automatically locks to prevent damage from overheating. CHECK SUSPENSION (if equipped). Displayed when the air suspension system is not operating properly. If this message is displayed while driving, pull off the road as soon as safely possible. For more information, refer to Air suspension in the Driving chapter. AIR SUSPENSION OFF (if equipped). Displayed when the air suspension switch is in the OFF position. For more information, refer to Air suspension in the Driving chapter. CHECK FUEL CAP. Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap for proper installation. Refer to Fuel filler cap in the Maintenance and Specifications chapter. CHECK COMPASS MODULE. Displayed when the compass is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. COMPASS NO RESPONSE. Displayed when the compass is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. DATA ERR. These messages indicate improper operation of the vehicle network communication between electronic modules. • Fuel computer • Charging system • Door sensor • Compass • Outside temperature • Engine sensor Contact your authorized dealer as soon as possible if these messages occur on a regular basis.

137

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED)

Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the

brake pedals.

Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.

LIFTGATE • To open the liftgate window, push

the control button under the center of the license plate lamp shield.

• To open the liftgate, position your hand on top of the liftgate handle and pull to open the liftgate. • Do not open the liftgate or

liftgate glass in a garage or other enclosed area with a low ceiling. If the liftgate glass is raised and the liftgate is also opened, both liftgate and glass could be damaged against a low ceiling.

• Do not leave the liftgate or liftgate glass open while driving. Doing so could cause serious damage to the liftgate and its components as well as allowing carbon monoxide to enter the vehicle.

Do not grab or pull the liftgate handle from the bottom. Doing so may cause wrist or arm injury.

138

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Driver Controls

Make sure the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. If you must drive with the liftgate

open, keep the vents open so outside air comes into the vehicle.

LUGGAGE RACK Your vehicle is equipped with a roof rack. The maximum recommended load is 200 lbs (90 kg), evenly distributed. If it is not possible to distribute the load, position it as far rearward as possible.

To adjust cross-bar position (if equipped): 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. Firmly tighten the thumbwheel at both ends of the cross-bar.

Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a

lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sport cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles. Failure to drive cautiously could result in an increase risk of loss of vehicle control, vehicle rollover, personal injury and death.

139

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through your authorized dealer. Refer to the SecuriLock娂 passive anti-theft system section later in this chapter for more information.

POWER DOOR LOCKS If the door does not unlock when the control is pressed, refer to the Power door lock disable feature section in this chapter. Press control to unlock all doors.

Press control to lock all doors.

Smart unlocking feature The smart unlocking feature helps prevent you from locking yourself out of the vehicle. With the key in any ignition position, the driver’s door will automatically unlock if it is locked using the power lock control on the driver’s door panel while the driver’s door is open.

140

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. Move lock control up to engage the childproof lock. Move control down to disengage childproof locks.

REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The remote entry system allows you to lock or unlock all vehicle doors and liftgate and open the liftgate window without a key. The remote entry lock/unlock feature operates in any ignition position. The liftgate glass feature operates as long as vehicle speed is less than 5 mph (8 km/h). The panic feature operates with the key in the 1
(OFF/LOCK) position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL remote entry transmitters are brought to the authorized dealer, to aid in troubleshooting.

141

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Unlocking the doors/liftgate Press this control to unlock the driver’s door. The interior lamps will illuminate with the ignition is in the 1 (OFF/LOCK) position. Press the control a second time within three seconds to unlock all doors and liftgate.

Locking the doors/liftgate Press this control to lock all doors and liftgate. The park/turn signal lamps will flash once. To confirm all doors are closed and locked, press the control a second time within three seconds; the park/turn signal lamps will flash once and the horn will chirp. If any of the doors or liftgate are ajar, the horn will make two quick chirps, reminding you to properly close all doors.

Opening the liftgate window Press the control to unlatch the liftgate window.

142

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Sounding a panic alarm Press this control to activate the alarm. The personal panic alarm will cycle the horn and parking lamps on/off. To deactivate the alarm, press the control again or turn the ignition to the 2 (ACCESSORY) or 3 (ON) position.

Memory feature (if equipped) The remote entry system can also control the memory feature. Press the control once to unlock the driver’s door. Pressing the control will automatically move the seat, rearview mirrors, and adjustable pedals to the desired memory position (the memory position corresponds to the transmitter being used).

Activating the memory feature To activate this feature: 1. Position the seat, rearview mirrors, and adjustable pedals to the positions you desire. 2. Press the SET control on the driver’s door panel. 3. Within 5 five seconds, press one control on the remote transmitter and then press the 1 or 2 control on the driver’s door panel to which you would like to associate with Driver 1
or Driver 2 positions. 4. Repeat this procedure for another remote transmitter if desired.

143

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Deactivating the memory seat feature To deactivate this feature: 1. Press the SET control on the driver’s door panel. 2. Within 5 five seconds, press any control on the remote transmitter which you would like to deactivate and then press the SET control on the driver’s door panel. 3. Repeat this procedure for another remote transmitter if desired.

Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together.

144

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement. Replacing lost transmitters If a remote transmitter has been lost and you would like to remove it from the vehicle’s memory, or you would like to purchase additional remote transmitters and have them programmed to your vehicle: • Take all your vehicle’s transmitters to your dealer for programming, or • Perform the programming procedure yourself. Programming remote transmitters It is necessary to have all (maximum of six — original and/or new) of your remote transmitters available prior to beginning this procedure. If all remote entry transmitters are not present during the programming procedure, the transmitters that are not present during programming will no longer operate the vehicle. Note: Do not press the brake pedal anytime during this sequencing, as doing so will invalidate the procedure. To program the transmitters yourself: • Unlock all doors using the power door lock/unlock control. Insert a key and turn the ignition from the 1 (OFF/LOCK) to the 3 (ON) position and cycle between 1 (OFF/LOCK) and 3 (ON) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 3 (ON) position. The locks will cycle to confirm that the programming mode has been entered.

• Within 20 seconds, program a remote transmitter by pressing any

button on a transmitter. The locks will cycle once to confirm that the remote transmitter has been programmed. (If more than 20 seconds pass before pressing a remote transmitter button, the programming mode will exit and the procedure will have to be repeated.) • Repeat the previous step to program additional remote transmitters. The locks will cycle once to confirm that each remote transmitter has been programmed. • When you have completed programming the remote transmitters, turn the ignition to the 1 (OFF/LOCK) position or wait 20 seconds. Again the doors will lock/unlock to confirm programming has been completed.

145

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Illuminated entry The lamps illuminate when the remote entry system is used to unlock the door(s). The system automatically turns off after 25 seconds or when the ignition is turned to the 2 (ACCESSORY) or 3 (ON) position. The dome lamp control must not be set to the off position for the illuminated entry system to operate.

Smart unlocking feature The smart unlocking feature prevents you from locking yourself out of the vehicle by unlocking the doors if the key is in the ignition and the driver’s door is open/ajar when the vehicle doors were locked using the power lock/unlock control. The smart unlocking feature operates independent of the position of the ignition. Autolocking feature The autolocking feature locks all vehicle doors when the following conditions are met: • All doors, including the liftgate, are closed. • The brake is pressed while the ignition is in the 3 (ON) position. • The transmission is in either a forward or reverse gear. • The vehicle has a speed of 5 mph (8 km/h) or greater. This feature relocks all doors if any door is opened, the brake is pressed after all doors are closed again and the vehicle has a speed of 5 mph (8 km/h) or greater. Deactivating/activating the autolock feature For vehicles equipped with a message center, the autolock feature may be deactivated/activated by selecting the autolock function (accessed by pressing the SETUP control). Press the RESET control to turn the autolock function on or off. Refer to Message center in the Driver Controls chapter for additional information. For vehicles not equipped with a message center, the feature may be deactivated by taking your vehicle to an authorized Ford dealer.

KEYLESS ENTRY SYSTEM (IF EQUIPPED) With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key, 146

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

• release the liftgate glass, • enable or disable the autolock function, and • add or delete a 5–digit personal user code. Your vehicle has a factory set 5–digit code that operates the keyless entry system. You can also program your own 5–digit personal entry code. The factory-set code is located: • on the owner’s wallet card in the glove compartment, • at your authorized dealer, • or on the module located under the right-hand side of the instrument panel, adjacent to the passenger compartment fuse panel.

Note: The 5–digit code (e.g. 12345) will be in large, BOLD numbers on the module label.

When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation.

Anti-scan feature If the wrong code has been entered 7 times (35 consecutive button presses), the keypad is disabled for one minute and the keypad lamp will flash during this time. Note: Pressing 7 • 8 and the 9 • 0 simultaneously during this one minute period will still lock the vehicle. The anti-scan feature will turn off after one minute of keypad inactivity.

147

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Programming your own personal entry code To program your own code: 1. Enter the factory set code (keypad will illuminate when pressed). 2. Press the 1 • 2 control within five seconds of Step 1. 3. Enter your personal 5–digit code. Enter each digit within five seconds of previous one. 4. After the code is entered, the locks will cycle, confirming that the new code has been set. Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that your authorized dealer gave you. You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the first personal code in favor of the new code. If you wish to erase your personal code, use the following instructions: 1. Enter the factory set code. 2. Press the 1 • 2 control and release. The system will now only respond to the factory set code.

Unlocking and locking the doors, liftgate and liftgate window using keyless entry To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. The interior lamps will illuminate. To unlock all doors and liftgate, press the 3 • 4 control within five seconds. To open the liftgate window, press the 5 • 6 control within five seconds. To lock all doors, liftgate and liftgate window, press the 7 • 8 and the 9 • 0 at the same time. Note: The driver’s door must be closed. You do not need to enter the keypad code first.

Activating/deactivating autolock with the keyless entry system 1. Turn the ignition to the 1 (OFF/LOCK) position. 2. Close all the doors, the liftgate and liftgate window.

148

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

3. Enter the 5–digit entry code 4. Press and hold the 7 • 8. While holding the 7 • 8 press the 3 • 4. 5. Release the 3 • 4. 6. Release the 7 • 8. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled.

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Theft indicator The theft indicator is the flashing red indicator located on the dash panel. • When the ignition is in the 1 (OFF/LOCK) position, the indicator will

flash once every 2 seconds to indicate the SecuriLock娂 system is functioning as a theft deterrent.

• When the ignition is in the 3 (ON) position, the indicator will glow for

3 seconds to indicate normal system functionality.

If a problem occurs with the SecuriLock娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position. If this occurs, the vehicle should be taken to an authorized dealer for service.

149

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Automatic arming The vehicle is armed immediately after switching the ignition to the 1 (OFF/LOCK) position.

Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle.

gasoline or similar items

Key information Your vehicle is supplied with two coded keys. Only a coded key will start your vehicle. Spare coded keys can be purchased from your authorized dealer. Your authorized dealer can program your key or you can “do it yourself.” Refer to the Programming spare keys section in this chapter. The following items may prevent the vehicle from starting: • Large metallic objects • Electronic devices on the key chain that can be used to purchase • A second key on the same key ring as the coded key If any of these items are present, you need to keep these objects from touching the coded key while starting the engine. These objects and devices cannot damage the coded key, but can cause a momentary “no start” condition if they are too close to the key during engine start. If a problem occurs, turn ignition the OFF position and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Ford coded key. If your keys are lost or stolen you will need to do the following: • Use your spare key to start the vehicle, or • Have your vehicle towed to a authorized dealer or a locksmith. The

key codes will need to be erased from your vehicle and new key codes will need to be re-coded.

150

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience. The correct coded key must be used for your vehicle. The use of the wrong type of coded key may lead to a “no start” condition. If an unprogrammed key is used in the ignition it will cause a “no start” condition.

Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock娂 keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure. If two previously programmed coded keys are not available, you must bring your vehicle to your authorized dealer to have the spare coded key(s) programmed. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition and turn the ignition from the 1 (OFF/LOCK) to the 3 (ON) position [maintain ignition in 3 (ON) for at least three seconds, but no more than ten seconds]. 2. Turn ignition from 3 (ON) back to the 1 (OFF/LOCK) position in order to remove the first coded key from the ignition. 3. Within ten seconds of removing the first coded key, insert the second previously programmed coded key into the ignition and turn the ignition from the 1 (OFF/LOCK) to the 3 (ON) position [maintain ignition in 3
(ON) for at least three seconds but no more than ten seconds]. 4. Turn the ignition from the 3 (ON) back to 1 (OFF/LOCK) position in order to remove the second coded key from the ignition. 5. Within 10 seconds of removing the second coded key, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from the 1 (OFF/LOCK) to the 3 (ON) position [maintain ignition in 3 (ON) for at least three seconds, but no more than ten seconds]. This step will program your new key to a coded key.

151

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Locks and Security

6. To program additional new unprogrammed key(s), repeat this procedure from Step 1. If successful, the new coded key(s) will start the vehicle’s engine and the theft indicator will illuminate for three seconds and then go out. If not successful, the new coded key(s) will not start the vehicle’s engine and the theft indicator will flash on and off and you may repeat Steps 1
through 5. If failure repeats, bring your vehicle to your authorized dealer to have the new spare key(s) programmed.

152

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

SEATING

Front row adjustable head restraints (if equipped) Your vehicle’s seats are equipped with two-way adjustable head restraints. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head. Refer to the following illustration to raise and lower the head restraints. The head restraints can be moved up and down.

Push control to lower head restraint.

Adjusting the front manual seat (if equipped)

Never adjust the driver’s seat or seatback when the vehicle is moving.

Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop.

153

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Lift handle to move seat forward or backward.

Seat recliner

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Pull the seatback handle up to recline the seat.

154

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Using the armrest (if equipped) Push the release control to move the armrest up or down.

Using the manual lumbar support The lumbar support control is located on the outboard side of the seat. Turn the lumbar support control forward for more support. Turn the lumbar support backward for less support.

Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the control to adjust firmness. Press the rear side of the control to adjust softness.

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

155

Seating and Safety Restraints

Adjusting the front power seat (if equipped)

Never adjust the driver’s seat or seatback when the vehicle is moving.

Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

The control is located on the outboard side of the seat cushion. Press the front or rear portion to tilt the seat.

Press the control to move the seat forward, backward, up or down.

156

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Memory seats/rearview mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to two programmable positions. The memory seat control is located on the driver door. • To program position one, move the driver seat, rearview mirrors, and adjustable pedals to the desired position. Press the SET control. The SET control indicator light will briefly illuminate. While the light is illuminated, press control 1. • To program position two, repeat the previous procedure using control

2.

A position can only be recalled when the transmission gearshift is in Park or Neutral. A memory position may be programmed at any time. The memory positions can also be recalled when you press your remote entry transmitter UNLOCK control. To program the memory function to a specific remote entry transmitter, refer to Remote entry system in the Locks and Security chapter.

Climate controlled seats operation (if equipped) The controls for the climate controlled seats are located on the dual electronic automatic temperature control (DATC) system. Refer to Climate Controls for more information. Climate controlled seats air filter replacement The climate controlled seat system includes an air filter that has to be replaced periodically. Refer to the scheduled maintenance information for more information.

157

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints • There is a filter located under

both front seats.

(cid:0)(cid:0)(cid:0)(cid:0)

(cid:0)(cid:0)(cid:0)(cid:0)

• It can be accessed from the

second row seat. Move the front seat all the way forward and up to ease access.

To remove climate controlled seat air filter: • Remove key from ignition. • Push on the outside rigid edge of

the air filter at the center and rotate downward once tab is released.

• Remove filter.

158

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

To install climate controlled seat air filter: • First, position the filter in it’s

housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.

REAR SEATS

Second row seats Your vehicle’s second row outboard seating positions are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. The head restraints can be raised by lifting. To lower the head restraint, press the release button.

If the head restraint becomes detached, replace the notched bar into the bezel while holding the release button.

Second row folding seat system Ensure that no objects such as books, purses or briefcases are on the floor in front of the second row seats or on the seat cushion before folding them down. Ensure that the head restraints are lowered. Move the front passenger seat forward so that the second row seat headrest clears the front seat. For assistance, refer to the label located on the side of the seat cushion.

159

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

Adjusting the 2nd row outboard seat for E-Z Entry The 2nd row outboard seats allow for easier entry and exit to and from the 3rd row seat. To enter the 3rd row seat: 1. Locate the handle on the side of the seat, lifting it to release the seatback.

2. Pull up on the handle located at the back of the seat. The seat will flip forward.

160

2006 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus)

Seating and Safety Restraints

3. To return the seat to a seating position, push down on the seat until the seat is latched to the floor.

4. With the seat in the flat back position, lift up on the lever located on the side of the seat cushion. This will allow the seat back to be lifted to the upright locked position. 5. Lift the seatback to the upright position.

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the

seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.

Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury

during a sudden stop.