2003 Ford Crown Victoria Owners Manual

Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

Working with the engine on 1. Set the parking brake and shift to P (Park). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running.

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front of the hood. 3. Lift the hood until the lift cylinders hold it open.

198

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT

4.6L SOHC V8 engine

199

1. Brake fluid reservoir 2. Engine oil dipstick 3. Windshield washer fluid reservoir 4. Air filter assembly 5. Power steering fluid reservoir 6. Engine coolant reservoir 7. Battery 8. Engine oil filler cap 9. Automatic transmission fluid dipstick

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter.

State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive. Washer fluids containing non-methanol antifreeze agents should be used only if they provide cold weather protection without damaging the vehicle’s paint finish, wiper blades or washer system.

If you operate your vehicle in temperatures below 4.5° C (40° F), use washer fluid with antifreeze protection. Failure to use

washer fluid with antifreeze protection in cold weather could result in impaired windshield vision and increase the risk of injury or accident.

Note: Do not put washer fluid in the engine coolant reservoir. Washer fluid placed in the cooling system may harm engine and cooling system components.

ENGINE OIL

Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait up to 10 minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat.

200

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

5. Locate and carefully remove the engine oil level indicator (dipstick).

DO NOT OVERFILL

6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within this

range, the oil level is acceptable. DO NOT ADD OIL.

• If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range.

201

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter.

• Do not overfill the engine

with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by a qualified service technician.

7. Put the indicator back in and ensure it is fully seated.

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal operating range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the normal operating range on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise until three clicks can be heard. To avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed.

202

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

Engine oil and filter recommendations Look for this certification trademark.

Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). To protect your engine’s warranty use Motorcraft SAE 5W-20 or an equivalent 5W-20 oil meeting Ford specification WSS-M2C153–H. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine. Do not use supplemental engine oil additives, cleaners or other engine treatments. They are unnecessary and could lead to engine damage that is not covered by Ford warranty. Change your engine oil according to the appropriate schedule listed in the scheduled maintenance guide. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.

203

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.

However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the scheduled maintenance guide for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells. If the electrolyte level in the battery is low, you can add plain tap water to the battery, as long as you do not use hard water (water with a high mineral or alkali content). If possible, however, try to only fill the battery cells with distilled water. If the battery needs water often, have the charging system checked. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water.

Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted

substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.

204

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps,

resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.

Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attention. If acid is swallowed, call a physician immediately.

Battery posts, terminals and related accessories contain lead and lead compounds. Wash hands after handling.

Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Release the parking brake. With your foot on the brake pedal and with the A/C on, put the vehicle in D (Drive) and allow the engine to idle for at least one minute. 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 16 km (10 miles) or more to • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.

relearn the idle and fuel trim strategy.

If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected.

205

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.

RECYCLE

ENGINE COOLANT

Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the scheduled maintenance guide. The coolant concentration should be maintained at 50/50 coolant and distilled water, which equates to a freeze point of -36° C (-34° F). Coolant concentration testing is possible with a hydrometer or antifreeze tester (such as the Rotunda Battery and Antifreeze Tester, 014–R1060). The level of coolant should be maintained at the “cold full” of “cold fill range” level in the coolant reservoir. If the level falls below, add coolant per the instructions in the Adding engine coolant section. Your vehicle was factory-filled with a 50/50 engine coolant and water concentration. If the concentration of coolant falls below 40% or above 60%, the engine parts could become damaged or not work properly. A 50–50 mixture of coolant and water provides the following: • Freeze protection down to -36° C (-34° F). • Boiling protection up to 129° C (265° F). • Protection against rust and other forms of corrosion. • Enables calibrated gauges to work properly.

206

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

When the engine is cold, check the level of the engine coolant in the reservoir.

• The engine coolant should be at the “cold fill level” or within the “cold

fill range” as listed on the engine coolant reservoir (depending upon application).

• Refer to the Scheduled Maintenance Guide for service interval • Be sure to read and understand Precautions when servicing your

schedules.

vehicle in this chapter.

If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty. If the reservoir is low or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location. Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained.

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.

Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could

make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant

(yellow-colored), VC-7–A (VC-7–B in Oregon), meeting Ford Specification WSS-M97B51–A1.

207

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan. • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Speciality Orange Engine Coolant, VC-2 (US) or CXC-209 (Canada), meeting Ford specification WSS-M97B44–D with the factory-filled coolant. Mixing Motorcraft Speciality Orange Engine Coolant or any orange-colored extended life product with your factory filled coolant can result in degraded corrosion protection. • A large amount of water without engine coolant may be added, in case of emergency, to reach a vehicle service location. In this instance, the cooling system must be drained and refilled with a 50/50 mixture of engine coolant and distilled water as soon as possible. Water alone (without engine coolant) can cause engine damage from corrosion, overheating or freezing. • Do not use alcohol, methanol, brine or any engine coolants mixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing.

• Do not add extra inhibitors or additives to the coolant. These

can be harmful and compromise the corrosion protection of the engine coolant.

For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “cold full” level. For all other vehicles, which have a coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant.

To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The

cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly.

1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (an opaque plastic bottle). Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases.

208

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

4. When you are sure that all the pressure has been released, use the cloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (see above), to within the “cold fill range” or the “cold full” level on the reservoir. If you removed the radiator cap in an overflow system, fill the radiator until the coolant is visible and radiator is almost full. 6. Replace the cap. Turn until tightly installed. (Cap must be tightly installed to prevent coolant loss.) After any coolant has been added, check the coolant concentration, refer to Checking Engine Coolant section. If the concentration is not 50/50
(protection to –34° F/–36° C), drain some coolant and adjust the concentration. It may take several drains and additions to obtain a 50/50
coolant concentration. Whenever coolant has been added, the coolant level in the coolant reservoir should be checked the next few times you drive the vehicle. If necessary, add enough 50/50 concentration of engine coolant and distilled water to bring the liquid level to the proper level. If you have to add more than 1.0 liter (1.0 quart) of engine coolant per month, have your dealer check the engine cooling system. Your cooling system may have a leak. Operating an engine with a low level of coolant can result in engine overheating and possible engine damage.

Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available.

Used engine coolant should be disposed of in an appropriate

manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter.

209

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • It may be necessary to increase the coolant concentration • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will

above 50%.

decrease the overheat protection characteristics of the engine coolant and may cause engine damage.

• Refer to the chart on the coolant container to ensure the

coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months.

above 40%.

If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentration • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% will

decrease the corrosion protection characteristics of the engine coolant and may cause engine damage.

• Decreased engine coolant concentrations below 40% will

decrease the freeze protection characteristics of the engine coolant and may cause engine damage.

• Refer to the chart on the coolant container to ensure the

coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive.

Vehicles driven year-round in non-extreme climates should use a 50/50
mixture of engine coolant and distilled water for optimum cooling system and engine protection.

What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain.

210

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

How fail-safe cooling works • Standard cluster

• Optional cluster

TEMP

If the engine begins to overheat: • The engine coolant temperature gauge will move to the H (hot) area • The engine coolant temperature gauge will illuminate all eight bars

(if your vehicle is equipped with analog gauges).

and a tone will sound every five seconds for one minute (if your vehicle is equipped with digital gauges).

• The Check Engine indicator light will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • If your vehicle is equipped with digital gauges, the gauge bars will

flash and a tone will sound every five seconds for one minute.

211

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications • The engine will completely shut down, causing steering and braking

effort to increase.

Once the engine temperature cools, the engine can be re-started. Take your vehicle to a service facility as soon as possible to minimize engine damage.

When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the road as soon as safely possible and turn off the engine. 2. Arrange for the vehicle to be taken to a service facility. 3. If this is not possible, wait a short period for the engine to cool. 4. Check the coolant level and replenish if low.

Never remove the coolant reservoir cap while the engine is running or hot.

5. Re-start the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible.

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS

Important safety precautions

Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.

The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops

before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.

212

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.

Automotive fuels can cause serious injury or death if misused or mishandled.

Gasoline may contain benzene, which is a cancer-causing agent.

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials

and any open flames before fueling your vehicle.

• Always turn off the vehicle before • Automotive fuels can be harmful

fueling.

or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind

can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury.

• Fuels can also be harmful if absorbed through the skin. If fuel is

splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is

213

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.

When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while

refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes.

The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an

ungrounded fuel container.

Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including the • Keep the fuel pump nozzle in contact with the fuel container while • DO NOT use a device that would hold the fuel pump handle in the fill

cargo area).

filling.

position.

Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/off feature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops. “Check Fuel Cap” illuminates when the ignition is turned to the ON position to ensure your bulb is working. When this light turns on, check the fuel filler cap. Continuing to operate the vehicle with the Check Fuel

214

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

Cap light on, can activate the Service Engine Soon warning. When the fuel filler cap is properly re-installed, the light(s) will turn off after a period of normal driving. It may take a long period of time for the system to detect an improperly installed fuel filler cap. If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used.

The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops

before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.

If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.

Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Do not use fuel containing methanol. It can damage critical fuel system components. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based compounds containing MMT. Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty.

Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. We do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your dealer or a qualified service technician to prevent any engine damage.

87(R+M)/2 METHOD

215

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Regular” unleaded gasoline. “Premium” unleaded gasoline is not recommended (particularly in the United States) because it may cause these problems to become more pronounced. If the problems persist, see your dealer or a qualified service technician. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quality fuel of the recommended octane rating. Aftermarket products could cause damage to the fuel system. Repairs to correct the effects of using an aftermarket product in your fuel may not be covered by your warranty. Many of the world’s automakers issued the World-wide Fuel Charter that recommends gasoline specifications to provide improved performance and emission control system protection for your vehicle. Gasolines that meet the World-wide Fuel Charter should be used when available. Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter.

Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality.

Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after

refueling, to allow the fuel system to pump the fuel from the tank to the engine. • Your “Check Engine” indicator may come on. For more information on

the “Check Engine” indicator, refer to the Instrument Cluster chapter.

Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician. Refer to the scheduled maintenance guide for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used.

216

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

ESSENTIALS OF GOOD FUEL ECONOMY

Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1,600 km (1,000
miles) of driving (engine break-in period). You will get a more accurate measurement after 3,000 km–5,000 km (2,000 miles-3,000 miles). Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill capacities section of this chapter. The advertised capacity is the amount of the indicated capacity and the empty reserve combined. Indicated capacity is the difference in the amount of fuel in a full tank and a tank when the fuel gauge indicates empty. Empty reserve is the small amount of fuel remaining in the fuel tank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling, • Use the same filling rate setting (low — medium — high) each time • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing the • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in kilometers or miles).

an error in the reading will result if the engine is left running.

same direction each time you fill up.

the tank is filled.

217

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy:

Calculation 1: Multiply liters used by 100, then divide by total kilometers traveled. Calculation 2: Divide total miles traveled by total gallons used.

Keep a record for at least one month and record the type of driving (city or highway). This will provide an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter will show how temperature impacts fuel economy. In general, lower temperatures give lower fuel economy.

fuel.

economy.

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel • Idling for long periods of time (greater than one minute) may waste • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy.

less fuel than traveling at 105 km/h [65 mph]).

218

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

economy.

reduce fuel economy.

• Warming up a vehicle on cold mornings is not required and may • Resting your foot on the brake pedal while driving may reduce fuel • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel • Use recommended engine oil. Refer to Lubricant specifications in • Perform all regularly scheduled maintenance items. Follow the

this chapter.

economy.

recommended maintenance schedule and owner maintenance checks found in your vehicle scheduled maintenance guide.

at any speed.

Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy • Carrying unnecessary weight may reduce fuel economy (approximately • Adding certain accessories to your vehicle (for example bug

0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried).

driving on hilly terrain.

deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy.

12–16 km (8–10 miles) of driving.

• Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first • Driving on flat terrain offers improved fuel economy as compared to • Transmissions give their best fuel economy when operated in the top • Close windows for high speed driving. EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles.

cruise gear and with steady pressure on the gas pedal.

219

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of L/100 km (MPG) expected on the vehicle under optimum conditions. Your fuel economy may vary depending upon the method of operation and conditions.

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. • Avoid running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at • Have the items listed in your scheduled maintenance guide performed

high speeds.

according to the specified schedule.

The scheduled maintenance items listed in the scheduled maintenance guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine

compartment and exhaust system, which can start a fire.

Illumination of the “Check Engine” light, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly.

Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment.

Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not

220

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your Warranty Guide for complete emission warranty information.

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the Warning lights and chimes section of the Instrument cluster chapter. Your vehicle may not pass the I/M test with the “Check Engine/Service Engine Soon” light on. If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop-and-go, city-type traffic with

at least four idle periods.

Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete.

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only MERCON威 ATF.

1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).

221

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range.

D O NOT V E RFILL

FLUID RSTEE

WE

MAX MIN

5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir.

BRAKE FLUID RESERVOIR The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels below the “MAX” line that do not trigger the brake system warning lamp are within the normal operating range, there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of your brake system could be compromised, seek service from your dealer immediately.

MAX

TRANSMISSION FLUID

Checking automatic transmission fluid (if equipped) Refer to your scheduled maintenance guide for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage. Automatic transmission fluid expands when warmed. To obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot

222

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

weather or pulling a trailer, the vehicle should be turned off for about 30
minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3. With the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated area for normal operating temperature or ambient temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is above 10°C (50°F).

DON’T ADD

Correct fluid level The transmission fluid should be checked at normal operating temperature 66°C-77°C (150°F-170°F) on a level surface. The normal operating temperature can be reached after approximately 30 km (20 miles) of driving. You can check the fluid without driving if the ambient temperature is above 10°C (50°F). However, if fluid is added at this time, an overfill condition could result when the vehicle reaches normal operating temperature.

223

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]).

The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]).

DON’T ADD

DON’T ADD

DON’T ADD

High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in this chapter. Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary, add fluid in 250 ml (1/2 pint) increments through the filler tube until the level is correct.

224

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

If an overfill occurs, excess fluid should be removed by a qualified technician. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components.

DON’T ADD

AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft Part Numbers. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running.

Changing the air filter element 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing. 5. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated.

6. Replace the air filter housing cover and secure the clamps. 7. Replace the air inlet tube and secure the clamp.

225

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be voided for any damage to the engine if the correct air filter element is not used.

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set. Tire Quality Grades apply to new pneumatic tires for use on passenger cars. They do not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.

Traction AA A B C The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.

226

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include

acceleration, cornering, hydroplaning or peak traction characteristics.

Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent higher levels of performance on the laboratory test wheel than the minimum required by law.

The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed,

underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

SERVICING YOUR TIRES

Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been

parked for at least one hour or has been driven less than 5 km (3
miles). • Adjust tire pressure to recommended specifications found on the

Certification label and inside fuel door.

Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control.

Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the scheduled maintenance guide. If you notice that the tires wear unevenly, have them checked.

227

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications • Four tire rotation (for vehicles

with aluminum wheels)

• Five tire rotation (for vehicles with steel wheels and full size spare tires)

Replacing the tires Replace the tires when the wear band is visible through the tire treads.

228

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the

Certification or Tire Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label. If you do not follow these precautions, your vehicle may not drive properly and safely.

Make sure that all replacement tires are of the same size, type, load-carrying capacity and tread design (e.g., “All Terrain”,

“Touring”, etc.), as originally offered by Ford.

Failure to follow these precautions may adversely affect the handling of the vehicle, and increase the risk of loss of vehicle

control, vehicle rollover and/or personal injury.

Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS

Snow tires must be the same size and grade as the tires you currently have on your vehicle.

The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains. Follow these guidelines when using snow tires and chains: • Either cable type chains or SAE class S chains can be used. • Install chains securely, verifying that the chains do not touch any • Drive cautiously. If you hear the chains rub or bang against your

wiring, brake lines or fuel lines.

vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent damage to your vehicle.

• If possible, avoid fully loading your vehicle. • Remove the tire chains when they are no longer needed. Do not use • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.

tire chains on dry roads.

229

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

MOTORCRAFT PART NUMBERS Component Air filter element Fuel filter Battery-standard Battery-heavy duty Oil filter PCV valve Spark plugs* * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.

4.6L SOHC V8 engine FA-1668
FG-986B BXT-65–650
BXT-65–750
FL-820-S EV-258
AWSF-32P

Ford Part Name Motorcraft SAE 5W-20
Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W-20
Super Premium Motor Oil (Canada) Motorcraft High Performance DOT 3
Motor Vehicle Brake Fluid1
Motorcraft MERCON威 ATF Motorcraft MERCON威V ATF Motorcraft Premium Gold Engine Coolant (yellow-colored) N/A

Capacity

5.7L (6.0 quarts)

Fill to line on reservoir

Fill to line on reservoir

13.2L (13.9 quarts) 3

18.0L (19.0 quarts)

71.9L (19.0 gallons)

REFILL CAPACITIES Fluid Engine oil (includes filter change)6

Brake fluid

Power steering fluid

Transmission fluid 2

Engine coolant 4

Fuel tank

230

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

Fluid Rear axle lubricant 5

Windshield washer fluid

Ford Part Name Motorcraft SAE 80W-90 Premium Rear Axle Lubricant Motorcraft Premium Windshield Washer Concentrate

Capacity

2.4L (5.0 pints)

Fill to line on reservoir

1Use only brake fluids certified to meet Ford specifications. Refer to Lubricant Specifications in this chapter. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used. 2Ensure the correct automatic transmission fluid is used. MERCON威 and MERCON威 V are not interchangeable. DO NOT MIX MERCON威 and MERCON威 V. Refer to the scheduled maintenance guide to determine the correct service interval. 3Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with an in-tank cooler. The amount of transmission fluid and fluid level should be set by the indication on the dipstick’s normal operating range. Police or Handling Package refill capacity-12.1L (12.8 quarts). 4Add the coolant type originally equipped in your vehicle. 5Rear axles are considered lubricated for life when the vehicle is used for normal service. See your scheduled maintenance guide for Severe Duty requirements. Traction-Lok axles use 2.1-2.3L (4.50-4.75 pints) of rear axle lubricant. Add 118 ml (4 oz.) of Additive Friction Modifier XL-3 or equivalent meeting Ford specification EST-M2C118–A for complete refill of Traction-Lok rear axle. Service refill capacities are determined by filling the rear axle 6 mm to 14 mm (1/4 inch to 9/16 inch) below the bottom of the filler hole. 6Use of sythetic or sythetic blend motor oil is not mandatory. Engine oil need only meet the requirements of Ford specification WSS-M2C153–H and the API Certification mark.

231

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

LUBRICANT SPECIFICATIONS Item

Engine coolant Motorcraft

Ford part name Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid 1
Silicone Lubricant

Premium Gold Engine Coolant (yellow-colored) Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W-20 Super Premium Motor Oil (Canada) Multi-Purpose Grease

Ford part number PM-1

Ford specification ESA-M6C25-A and DOT 3

F7AZ-19G208-BA and F5AZ-19553-AA VC-7–A

ESR-M13P4-A

WSS- M97B51–A1

XO-5W20-QSP (US) CXO-5W20–LSP12
(Canada)

WSS-M2C153-H with API Certification Mark

XG-4 or F5AZ-19G209-AA

ESR-M1C159-A

Penetrating and Lock Lubricant Motorcraft MERCON威 ATF Motorcraft MERCON威V ATF3

Motorcraft XL-1 none

XT-2-QDX

MERCON威

XT-5-QM

MERCON威V

Brake fluid

Door weatherstrips

Engine oil

Hinges, latches, striker plates, fuel filler door hinge and seat tracks Lock cylinders

Power steering fluid Automatic transmission

232

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

Item

Rear Axle Lubricant 2

Windshield washer fluid

Ford part name Motorcraft SAE 80W-90
Premium Rear Axle Lubricant Ultra-clear Windshield Washer Concentrate

Ford part number XY-80W90-QL

Ford specification WSP-M2C197-A

ZC-18–A

ESR-M17P5-A

1Use only brake fluids certified to meet Ford specifications. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used. 2Add 118 ml (4 oz.) of Additive Friction Modifier XL-2 or equivalent meeting Ford specification EST-M2C118-A for complete refill of Traction-Lok rear axles. 3Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle. MERCON威 and MERCON威 V are not interchangeable. DO NOT mix MERCON威 and MERCON威 V. Refer to your scheduled maintenance guide to determine the correct service interval.

ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio

VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width

4.6L V8 engine 281
87 octane 1-3-7-2-6-5-4-8
1.3-1.4 mm (0.052-0.056 inch) Coil on plug 9.4:1

mm (in) 5 386 (212)/5538 (218)a 1 987 (78.2)

233

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

Vehicle dimensions (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear a Denotes long wheel base

mm (in) 1 443 (56.8) 2 913 (114.7)/3066 (120.7)a 1 611 (63.4) 1 666 (65.6)

234

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

IDENTIFYING YOUR VEHICLE

Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.

MFD. BY FORD MOTOR CO. IN U.S.A. GVWR:XXXXXXXXXXXX

DATE: XXXXX FRONT GAWR: XXXXXX/XXXXXXX REAR GAWR: XXXXXXX/XXXXXXX

THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL MOTOR VEHICLE SAFETY, BUMPER, AND THEFT PRE- VENTION STANDARDS IN EFFECT ON THE DATE OF MANUFACTURE SHOWN ABOVE.

VIN: XXXXXXXXXXXXXXXXXX TYPE: XXXXXXXXXXXXXXX

XXXXX XXXXX

EXT PNT: XXXXXX XXXXXX BAR INT TR TP/PS R AXLE TR SPR X XX XXX X XX X XXXX

RC: XX

DSO: XXXX

UPC ∇F85B-1520472-AB

Vehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.)

XXXXXXXXXXXXXXXXX

235

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Maintenance and Specifications

1. World manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number

Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).

236

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Accessories

Accessories

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln, Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made from high quality materials and meets or exceeds Ford’s rigorous engineering and safety specifications. Ford Motor Company will repair or replace any properly dealer-installed Ford accessory found to be defective in factory-supplied materials or workmanship during the warranty period, as well as any component damaged by the defective accessory. The accessory will be warranted for whichever provides you the greatest benefit: • 12 months or 20,000 km (12,000 miles) (whichever occurs first), or • the remainder of your new vehicle limited warranty. This means that genuine Ford accessories purchased along with your new vehicle and installed by the dealer are covered for the full length of your New Vehicle’s Limited Warranty — 3 years or 60,000 km (36,000
miles) (whichever occurs first). Contact your dealer for details and a copy of the warranty. Not all accessories are available for all models. Following is a list of several Ford Genuine Accessory products. Not all accessories are available for all models. To find out what accessories are available for your vehicle, please contact your dealer or visit our online store at: www.fordaccessories.com.

Vehicle Security Air bag anti-theft locks Locking gas cap Remote keyless entry Styled wheel locks Underbody security lighting Vehicle security systems

237

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Accessories

Comfort and convenience Cargo net Cargo organizer Electrochromic compass mirror Electrochromic compass mirror with temperature display Engine block heaters Remote start system

Travel equipment Daytime running lights (DRL)

Protection and appearance equipment All-weather floor mats Carpeted floor mats Door edge guards First aid kit Flat splash guards Front end covers Full vehicle cover Highway safety kit Molded splash guards Side window deflectors Styled hood deflector Universal floor mats

238

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Accessories

For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety compliance certification label). Consult your dealer for specific weight information. • The Federal Communications Commission (FCC) and Canadian Radio Telecommunications Commission (CRTC) regulate the use of mobile communications systems - such as two-way radios, telephones and theft alarms - that are equipped with radio transmitters. Any such equipment installed in your vehicle should comply with FCC or CRTC regulations and should be installed only by a qualified service technician.

• Mobile communications systems may harm the operation of your

vehicle, particularly if they are not properly designed for automotive use or are not properly installed. When operated, such systems may cause the engine to stumble or stall or cause the transmission to be damaged or operate improperly. In addition, such systems may be damaged or their performance may be affected by operating your vehicle. (Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily effect your vehicle’s operation.) • Ford cannot assume responsibility for any adverse effects or damage

that may result from the use of such equipment.

239

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Index

Index

ABS (see Brakes) .....................147
Air bag supplemental restraint system ................125, 129
and child safety seats ............127
description ......................125, 129
disposal ....................................132
driver air bag ..................127, 130
indicator light ...........13, 129, 131
operation .........................127, 130
passenger air bag ...........127, 130
side air bag ..............................129
Air cleaner filter ...............225, 230
Air conditioning ..........................49

manual heating and air conditioning system .................47
Air suspension ...........................151
description ..............................151
warning light .............................14

Antifreeze (see Engine coolant) ................206
Anti-lock brake system (see Brakes) ......................147–148
Audio system (see Radio) ...22, 31
Automatic transmission

driving an automatic overdrive .................................153
fluid, adding ............................222
fluid, checking ........................222
fluid, refill capacities ..............230
fluid, specification ..................233
Auxiliary power point .................73
Axle

lubricant specifications ..232–233
refill capacities ........................230
traction lok ..............................156

Battery .......................................204

240

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

acid, treating emergencies .....204
charging system warning light ............................................13
jumping a disabled battery ....176
maintenance-free ....................204
replacement, specifications ...230
servicing ..................................204
voltage gauge ............................19
BeltMinder .................................120
Brakes ........................................147
anti-lock ...........................147–148
anti-lock brake system (ABS) warning light .........12, 148
brake warning light ..................12
fluid, checking and adding ....222
fluid, refill capacities ..............230
fluid, specifications .........232–233
lubricant specifications ..232–233
parking ....................................149
shift interlock ..........................152
Bulbs ............................................56

Capacities for refilling fluids ....230
CD changer .................................42
CD-single premium .....................22
Cell phone use ............................91
Certification Label ....................235
Changing a tire .........................171
Child safety restraints ..............132
child safety belts ....................132
Child safety seats ......................135
attaching with tether straps ..139
in front seat ............................137
in rear seat ..............................137

Cleaning your vehicle

engine compartment ..............192

Index

Utilizing the Mediation/Arbitration Program ...................................187

Daytime running lamps (see Lamps) ................................54
Defrost

rear window ..............................53

Dipstick

automatic transmission fluid ..........................................222
engine oil .................................200

Doors

lubricant specifications ..........232

Driving under special conditions ..................................156
through water .........................156

Electronic message center .........86
Emergencies, roadside

jump-starting ..........................176
Emission control system ..........220
Engine ........................................233

check engine/service engine soon light ..................................10
cleaning ...................................192
coolant .....................................206
fail-safe coolant ......................210
idle speed control ...................204
lubrication specifications ..................232–233
refill capacities ........................230
service points ..........................199
starting after a collision .........163
Engine block heater .................146
Engine oil ..................................200

241

instrument panel ....................194
interior .............................194–195
interior trim ............................194
plastic parts ............................193
safety belts ..............................195
washing ....................................191
waxing .....................................191
wheels ......................................192
wiper blades ............................193

Climate control (see Air conditioning or Heating) ......47, 49
Clock ................................26, 35, 41
Compass, electronic

set zone adjustment .................67
Console ........................................92
overhead ..............................64, 66

Controls

power seat ...............................109
steering column ........................81

Coolant

checking and adding ..............206
refill capacities ................209, 230
specifications ..................232–233

Cruise control (see Speed control) ....................77
Customer Assistance ................162

Ford accessories for your vehicle .....................................196
Ford Extended Service Plan ..........................................184
Getting assistance outside the U.S. and Canada .....................188
Getting roadside assistance ...162
Getting the service you need .........................................182
Ordering additional owner’s literature .................................189
The Dispute Settlement Board .......................................184

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Gas cap (see Fuel cap) ......11, 214
Gas mileage (see Fuel economy) .................217
Gauges ...................................16–17
battery voltage gauge ...............19
engine coolant temperature gauge .........................................17
engine oil pressure gauge ........18
fuel gauge ..................................19
odometer ...................................20
speedometer .............................20
trip odometer ............................21

GAWR (Gross Axle Weight Rating) .......................................156
definition .................................156
driving with a heavy load ......156
location ....................................156

GVWR (Gross Vehicle Weight Rating) .......................................156
calculating ...............................156
definition .................................156
driving with a heavy load ......156
location ....................................156

Hazard flashers .........................163
Head restraints .........................106
Headlamps ...................................54
aiming ........................................55
autolamp system .......................54
bulb specifications ....................57
daytime running lights .............54
flash to pass ..............................55
high beam ...........................15, 55
replacing bulbs .........................57
turning on and off ....................54
warning chime ..........................16

Index

change oil soon warning, message center .......................200
checking and adding ..............200
dipstick ....................................200
filter, specifications ........203, 230
recommendations ...................203
refill capacities ........................230
specifications ..................232–233
Exhaust fumes ..........................146

Fail safe cooling ........................210
Floor mats ...................................92
Fluid capacities .........................230
Fuel ............................................212

calculating fuel economy ............................69, 217
cap .....................................11, 214
capacity ...................................230
choosing the right fuel ...........215
comparisons with EPA fuel economy estimates .................219
detergent in fuel .....................216
filling your vehicle with fuel ...........................212, 214, 217
filter, specifications ........216, 230
fuel filler door override ............91
fuel filler door release ..............90
fuel pump shut-off switch .....163
gauge .........................................19
improving fuel economy ........217
low fuel warning light ..............14
octane rating ...................215, 233
quality ......................................216
running out of fuel .................216
safety information relating to automotive fuels .....................212
Fuses ..................................164–165

Garage door opener ....................82

242

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Index

Lamps

autolamp system .......................54
bulb replacement specifications chart ..................57
cargo lamps ...............................55
daytime running light ...............54
headlamps .................................54
headlamps, flash to pass ..........55
instrument panel, dimming .....55
interior lamps .....................56–57
replacing bulbs .......56–57, 59, 61

Lane change indicator (see Turn signal) ........................56
Lights, warning and indicator ....10
air bag ........................................13
air suspension ...........................14
anti-lock brakes (ABS) ....12, 148
brake ..........................................12
charging system ........................13
check engine .............................10
fuel cap light .............................11
high beam .................................15
low fuel ......................................14
oil pressure ...............................13
overdrive off ..............................14
safety belt .................................13
speed control ............................80
traction control active ..............13
turn signal indicator .................14

Limited slip axle (see Traction Loc) ....................156
Load limits .................................156
GAWR ......................................156
GVWR ......................................156
trailer towing ..........................156

Locks

autolock .....................................99
childproof ..................................94
doors ..........................................93

243

Heating

heating and air conditioning system .................................47, 49

HomeLink universal transceiver (see Garage door opener) ...................70, 82, 85
Hood ..........................................198

Ignition ...............................143, 233
Infant seats (see Safety seats) .....................135
Inspection/maintenance (I/M) testing ........................................221
Instrument panel

cleaning ...................................194
cluster ........................................10
lighting up panel and interior .......................................55

Jack ............................................171
positioning ...............................171
storage .....................................171
Jump-starting your vehicle ......176

Keyless entry system ...............100
autolock .....................................99
keypad .....................................100
programming entry code .......101
Keys .............................93, 102–104
key in ignition chime ...............16
positions of the ignition .........143

2003 Crown Victoria (cro) Owners Guide (post-2002-fmt) USA English (fus)

Power mirrors .............................75
Power point .................................73
Power steering ..........................151
fluid, checking and adding ....221
fluid, refill capacity ................230
fluid, specifications .................232
Power Windows ...........................74

Radio ......................................22, 31
Radio reception ...........................46
Rear window defroster ...............53
Relays ................................164, 171
Remote entry system ...........95, 97
illuminated entry ......................99
locking/unlocking doors ...........96
opening the trunk .....................97
panic alarm ...............................97
replacement/additional transmitters ...............................98
replacing the batteries .............97
Roadside assistance ..................162

Safety Belt Maintenance ..........124
Safety belts (see Safety restraints) ............16, 110, 114–118
Safety defects, reporting ..........190
Safety restraints ........110, 114–118
belt minder .............................120
extension assembly ................124
for adults .........................115–117
for children .............................132
lap belt ....................................118
Occupant Classification Sensor ......................................112

Index

Lubricant specifications ...232–233
Lumbar support, seats .............108

Message center ...........................86
reset button ..............................86
select button .............................87

Mirrors

automatic dimming rearview mirror ........................................76
fold away ...................................76
heated ........................................75
side view mirrors (power) .......75
Moon roof ....................................81
Motorcraft parts ................216, 230

Octane rating ............................215
Odometer .....................................20
Oil (see Engine oil) ..................200
Overdrive .............................89, 154

Panic alarm feature, remote entry system ................................97
Parking brake ............................149