Download PDF Manual

interval between wipes will decrease. AUTOWIPERS (IF EQUIPPED) Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure you switch off the windshield wipers before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, install new wiper blades. Note: If you switch on the autolamps with the autowipers, the low beam headlamps will turn on automatically when the rain sensor turns on the windshield wipers continuously.


68


C-MAX (CCG)


E168040E168041 Wipers and Washers


Keep the outside of the windshield clean. The rain sensor is very sensitive. Dirt or debris around the interior rear view mirror area will affect the autowipers' performance. For example, the autowipers may turn on if dirt, mist or insects hit the windshield. WINDSHIELD WASHERS Note: Do not operate the washers when the washer reservoir is empty. This may cause the washer pump to overheat.


To operate the washers and spray the windshield, pull the lever toward you. When you release the lever, the wipers will operate for a short time. A wipe will occur a few seconds after washing to clear any remaining washer fluid.


Note: During wet or winter driving conditions with ice, snow or a salty road mist, inconsistent or unexpected wiping or smearing may occur. In these conditions, you can do the following: •


Lower the sensitivity of the autowipers to reduce the amount of smearing. Switch to normal or high-speed wipe. Switch the autowipers off.


• •


High sensitivity On Low sensitivity


The autowipers feature uses a rain sensor that is located in the area around the interior rear view mirror. The rain sensor monitors the amount of moisture on the windshield and automatically turns the wipers on. It will adjust the wiper speed by the amount of moisture that the sensor detects on the windshield. Use the rotary control to adjust the sensitivity of the rain sensor. Set the control to low sensitivity, and the wipers will turn on when the rain sensor detects a large amount of moisture on the windshield. Set the control to high sensitivity, and the wipers will turn on when the rain sensor detects a small amount of moisture on the windshield.


69


C-MAX (CCG)


E168041E168042 Wipers and Washers


REAR WINDOW WIPER AND WASHERS Rear Window Wiper


Rear Window Washer


To use the rear washer function, push the lever away from you. When you release the lever, the wiper will operate for a short time.


Intermittent wipe Low-speed wipe Off


Press the top of the button at the end of the lever to switch on the intermittent wiper. Press the button again to switch on low-speed wipe. Press the bottom of the button to switch the wiper off, or to change the wiper speed from low-speed to intermittent. When you shift into R (Reverse), the rear wiper will turn on to intermittent if the front wipers are activated.


70


C-MAX (CCG)


E168043E168044 Lighting


LIGHTING CONTROL


Headlamp Flasher


Off Parking lamps, instrument panel lamps, license plate lamps and tail lamps Headlamps


High Beams


Pull the lever toward you slightly and release it to flash the headlamps.


AUTOLAMPS (IF EQUIPPED)


Push the lever forward to switch the high beams on. Push the lever forward again or pull the lever toward you to switch the high beams off.


The headlamps will switch on and off automatically in low light situations or during inclement weather. The headlamps will remain on for a period of time after you switch the ignition off. Use the information display controls to adjust the period of time that the headlamps will remain on. See Information Displays (page 88).


71


C-MAX (CCG)


E142449E162679E162680E142451 Lighting


When the headlamp switch is in the Autolamps position, the windshield wiper activated exterior lamps will turn on within 10 seconds when you switch the windshield wipers on. The exterior lamps will turn off approximately 60 seconds after you switch the windshield wipers off. This feature does not turn on the exterior lamps: • • while the wipers are on to clear washer


during a mist wipe



fluid during a wash condition if the wipers are in automatic or intermittent modes.


Note: If you have autolamps and autowipers switched on the low beam headlamps will turn on automatically when the windshield wipers operate continuously. Note: You may have to manually switch the headlamps on in severe weather conditions. Note: If you have autolamps switched on you can only switch the high beam headlamps on once the system has turned the headlamps on. INSTRUMENT LIGHTING DIMMER Note: If you disconnect the battery or it becomes discharged, the illuminated components will switch to the maximum setting.


Vehicles With Front Fog Lamps


Press repeatedly or press and hold until the desired level is reached. Vehicles Without Front Fog Lamps


Press repeatedly or press and hold to dim. Press repeatedly or press and hold to brighten.


72


C-MAX (CCG)


E132712ABE165366 Lighting


HEADLAMP EXIT DELAY After you switch the ignition off, you can switch the headlamps on by pulling the direction indicator lever toward you. You will hear a short tone. The headlamps will switch off automatically after three minutes with any door open or 30 seconds after the last door has been closed. You can cancel this feature by pulling the direction indicator toward you again or switching the ignition on. DAYTIME RUNNING LAMPS (IF EQUIPPED)


WARNING


Always remember to switch your headlamps on in low light situations or during inclement weather. The system does not activate the tail lamps and may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.


The system switches the headlamps on with a reduced output in daylight conditions. To switch the system on: 1. Switch the ignition on. 2. Switch the lighting control to the off,


or parking lamp position.


3. Disengage the parking brake. 4. Make sure the transmission selector


lever is not in position P.


C-MAX (CCG)


FRONT FOG LAMPS


Press the control to switch the fog lamps on or off. You can switch the fog lamps on when the lighting control is in any position except Off and the high beams are not on. DIRECTION INDICATORS


Push the lever up or down to use the direction indicators. Note: Tap the lever up or down to make the direction indicators flash three times to indicate a lane change. INTERIOR LAMPS The lamps will switch on when one of the following conditions have been met:


73


E142453E162681 Lighting


With panorama roof


• • •


You open any door. You press a remote control button. You press switch B on the front interior lamp.


Front Interior Lamp Without panorama roof


(A) Door function switch. Press this switch to disable the interior lamps. The door function


indicator lamp will illuminate yellow with lamps disabled. Press the switch again to turn interior lamps back on. The indicator lamp will illuminate blue.


(B) All lamps on and off switch.


(C) Individual lamp on and off switch.


Rear Interior Lamp (If Equipped)


(A) You can switch individual map lamps on independently by pressing switch.


(A) Door function switch. Press this switch to disable the interior lamps. The door function


indicator lamp will illuminate yellow with lamps disabled. Press the switch again to turn interior lamps back on. The indicator lamp will illuminate blue.


(B) All lamps on and off switch.


(C)Passenger individual lamp on and off switch.


(D) Driver individual lamp on and off switch.


74


C-MAX (CCG)


E161163DCABE160819E160816E160817E160818E142454BACE160819E160816E160818AE142455 Lighting


AMBIENT LIGHTING (IF EQUIPPED) The ambient lighting system illuminates the interior with a choice of several colors. The ambient lighting control is located in the overhead console.


Color palette Control knob Search mode


Rotate B past the first detent to switch on and adjust to the desired brightness. Press A to cycle through the color choices. Press C to switch on all interior lamps and the ambient lighting. Press C again to switch off the interior lamps and return the ambient lighting to the previously selected color. The ambient lighting will switch on when the following conditions have been met: • • The ambient lighting will remain on until you switch the ignition off and one of the following conditions have been met: • •


you lock your vehicle the accessory delay timer expires.


you switch the ignition on you switch the headlamps on


75


C-MAX (CCG)


E142456ABC Windows and Mirrors


Window Lock


Press the control to lock or unlock the rear window controls. It illuminates when you lock the rear window controls. Bounce-Back (If Equipped) The window will stop automatically while closing. It will reverse some distance if there is an obstacle in the way. Overriding the Bounce-Back Feature


WARNING


When you override the bounce-back feature the window will not reverse if it detects an obstacle. Take care


when closing the windows to avoid personal injury or damage to your vehicle.


Proceed as follows to override this protection feature when there is a resistance, for example in winter: 1. Close the window twice until it reaches


the point of resistance and let it reverse.


POWER WINDOWS WARNINGS


Do not leave children unattended in your vehicle and do not let them play with the power windows. They may


seriously injure themselves.


When closing the power windows, you should verify they are free of obstructions and make sure that


children and pets are not in the proximity of the window openings.


Note: You may hear a pulsing noise when just one of the windows is open. Lower the opposite window slightly to reduce this noise. Press the switch to open the window. Lift the switch to close the window. One-Touch Down Press the switch fully and release it. Press again or lift it to stop the window. One-Touch Up Lift the switch fully and release it. Press or lift it again to stop the window.


76


C-MAX (CCG)


E70848E70850 Windows and Mirrors


GLOBAL OPENING You can use the remote control to operate the windows with the ignition off. Note: To operate this feature, accessory delay must not be active. Opening the Windows You can only open the windows for a short time after you unlock your vehicle with the remote control. After you unlock your vehicle, press and hold the remote control unlock button to open the windows. Release the button once movement starts. Press the lock or unlock button to stop movement. EXTERIOR MIRRORS Power Exterior Mirrors WARNING


Do not adjust the mirrors when your vehicle is moving.


Left-hand mirror Off Right-hand mirror


2. Close the window a third time to the point of resistance. The bounce-back feature is now disabled and you can close the window manually. The window will go past the point of resistance and you can close it fully.


See an authorized dealer as soon as possible if the window does not close after the third attempt. Resetting the Bounce-Back Feature


WARNING


The bounce-back feature remains turned off until you reset the memory.


If you have disconnected the battery, you must reset the bounce-back memory separately for each window. 1. Lift and hold the switch until the


window is fully closed.


2. Release the switch. 3. Lift the switch again for one more


second.


4. Press and hold the switch until the


window is fully open.


5. Release the switch. 6. Lift and hold the switch until the


window is fully closed.


7. Open the window and then try to close


it automatically.


8. Reset and repeat the procedure if the window does not close automatically.


Accessory Delay (If Equipped) You can use the window switches for several minutes after you switch the ignition off or until you open either front door.


77


C-MAX (CCG)


ACBE70846 Windows and Mirrors


Check the main mirror first before a lane change, then check the blind spot mirror. If no vehicles are present in the blind spot mirror and the traffic in the adjacent lane is at a safe distance, signal that you intend to change lanes. Glance over your shoulder to verify traffic is clear and carefully change lanes.


Press the arrows to adjust the mirror. Fold-Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position. Signal Indicator Mirrors The outer portion of the appropriate mirror housing blinks when you activate the turn signal. Heated Exterior Mirrors (If Equipped) See Heated Windows and Mirrors (page 107). Integrated Blind Spot Mirrors


WARNING


Objects in the blind spot mirror are closer than they appear.


Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They are designed to increase your visibility along the side of your vehicle.


78


C-MAX (CCG)


The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image will transition from the main mirror and begin to appear in the blind spot mirror as the vehicle approaches (B). The vehicle will transition to your peripheral field of view as it leaves the blind spot mirror (C).


E70847ABCE138665 Windows and Mirrors


SUN VISORS Illuminated Vanity Mirror (If Equipped)


Lift the cover to switch the lamp on. SUN SHADES (IF EQUIPPED)


WARNINGS


Do not let children play with the sun shade or leave them unattended in the vehicle. They may seriously hurt


themselves.


When closing the sun shade, you should verify that it is free of obstructions and make sure that


children and pets are not in the proximity of the sunshade.


The control is located in the overhead console. The sun shade has a one-touch open and close feature. To stop motion during one-touch operation, press the control a second time.


INTERIOR MIRROR WARNING


Do not adjust the mirror when your vehicle is moving.


Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia-based cleaning products. You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side. Pull the tab below the mirror toward you to reduce glare at night. Auto-Dimming Mirror (If Equipped) Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor. The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle. It will automatically return to normal reflection when you select reverse gear to make sure you have a clear view when backing up.


79


C-MAX (CCG)


E162197 Windows and Mirrors


4. Press and hold the rear of the control to the first action point, until the sun shade fully closes.


If you do not complete Step 2 within 15
seconds of Step 1, the relearning function end. Switch the ignition off, wait for another 30 seconds and then switch the ignition back on again. Start the procedure again from the beginning. Confirm that relearning was successful by opening and closing the sun shade.


Opening and Closing the Sun Shade


Fully press and release the front of the control to open the sun shade. Fully press and release the rear of the control to close the sun shade. Bounce-Back The sun shade will stop automatically while closing. It will reverse some distance if there is an obstacle in the way. Sun Shade Relearning WARNING


The bounce-back function is not active during this procedure. Make sure that there are no obstacles in


the way of the moving sun shade.


Note: You must start the relearning process within 30 seconds of switching the ignition on. In case the sun shade no longer opens or closes properly, follow this relearning procedure: 1. Press the front of the control to the first action point twice and release it within two seconds.


2. Press the rear of the control to the first action point twice and release it within two seconds.


3. Press and hold the front of the control


to the first action point, until the sun shade fully opens.


80


C-MAX (CCG)


E138668 Instrument Cluster


GAUGES


Left Information Display Speedometer Right Information Display See General Information (page 272).


Right Information Display Efficiency Leaves Efficiency leaves indicate short term driving efficiency. The more leaves and vines that are displayed, the better your fuel economy. Leaves and vines will occasionally appear and disappear to indicate a change in driving efficiency. Note: The efficiency leaves display can be impacted by your use of brakes, accelerator and accessories, as well as environmental conditions such as hills and weather.


Left Information Display Odometer Located in the bottom of the information display Registers the accumulated distance your vehicle has traveled. Fuel Economy See Common Displays below. For additional menu options. See General Information (page 88). Trip Computer See General Information (page 88). Vehicle Settings and Personalization See General Information (page 88).


81


C-MAX (CCG)


ACBE162393 Instrument Cluster


The high voltage battery gauge appears on the right side of the information display screen. This provides Charge Fill (State of Charge), Charge Assist and Regen Display. • Charge Fill (Hybrid Mode) - The fill


level, or State of Charge indicates the amount of energy stored in the high voltage battery as a percent of total energy capacity. The level will increase or decrease as the battery charges and discharges during normal operation.


• Charge Fill (Energi Plug-in Power Mode) - The fill level indicates the amount of energy stored in the high voltage battery which is available for Plug-in Power Mode. A full fill represents the total amount of energy you can get from an external charge (plugging your vehicle in). When the fill reaches empty your vehicle will automatically enter Hybrid Mode.


Note: The Charge Fill is always shown for Plug-in Power Mode, even if Charge Fill is not selected under Battery Display in the Options sub-menu.


Common Displays Fuel Economy Displays: Displays your average and instantaneous fuel economy on most Display Mode screens. Note: You can reset your average fuel economy by pressing and holding the OK button on the left hand steering wheel controls. Average fuel economy cannot be reset while on the MyView screen. • Average Fuel Economy - is


continuously averaged since the last reset. You can reset your average fuel economy by pressing and holding the OK button on the left hand steering wheel controls. For Energi vehicles both Hybrid and Plug-in Power mode operation will be included in the calculation. Instantaneous Fuel Economy - If your instantaneous fuel economy is greater than the maximum value displayed, a + sign will be shown next to the maximum scale number. When the vehicle is operating on battery power only, EV is displayed and the gauge fill is shown in blue.



Battery Gauge: Note: Battery gauge information can be individually selected on or off through Battery Display in the Options sub-menu. From any main display a right arrow press on the steering wheel controls will take you to the Options sub-menu. Note: For Energi vehicles there are two versions of the battery gauge. When the vehicle is in Hybrid Mode the information is shown with a simple battery graphic. When in Plug-in Power Mode an enhanced battery graphic is provided and available electric range is added to the display.


82


C-MAX (CCG)


Instrument Cluster


Brake Coach Display: The Brake Coach appears after your vehicle has come to a stop. It coaches you to brake in a manner which maximizes the amount of energy returned through the regenerative braking system. The percent displayed is an indication of the regenerative braking efficiency with 100% representing the maximum amount of energy recovery. Trip Summary: Trip Summary is displayed upon shutting off your vehicle. The data is calculated over the last on and off cycle. • Distance - The total distance traveled,


distance traveled on battery power only (EV distance) and Regen distance are displayed. Regen distance is the estimated range gained from energy recaptured through regenerative braking. Fuel Use - The average fuel economy and total fuel used are displayed. In addition for Energi, the total electrical energy used while in Plug-in Power Mode is displayed in kilowatt hours (kWh). Brake Score - The average percentage of braking energy recaptured and returned to the high voltage battery through regenerative braking. WARNING LAMPS AND INDICATORS The following warning lamps and indicators will alert you to a vehicle condition that may become serious. Some lamps will light when you start your vehicle to make sure they work. If any lamps remain on after starting your vehicle, refer to the respective system warning lamp for further information.





Electric Range (Energi Plug-in Power Mode) - The electric range estimate is personalized to the driver's key. The estimate is based on the amount of energy presently available in the high voltage battery and your typical energy usage while driving. This includes your drive habits as well as your use of accessories such as Climate Control. The available battery energy refers to the energy gained from charging the battery while plugged in.


• Charge Assist - The up and down


arrows provide information about the energy going into and out of the high voltage battery. The up arrow above the battery indicates battery charging such as from regenerative braking. The down arrow below the battery indicates battery discharging to provide power for propulsion or vehicle accessories.


• Regen Display - When stepping on the


brake pedal, a circular arrow symbol appears in the center of the Battery Gauge when energy is being recaptured through the regenerative braking system. Fuel Gauge: The fuel gauge will indicate approximately how much fuel is left in the fuel tank. The fuel gauge may vary slightly when your vehicle is moving or on a gradient. The arrow adjacent to the fuel pump symbol indicates on which side of the vehicle the fuel filler door is located.


83


C-MAX (CCG)


Instrument Cluster


Note: Some warning indicators appear in the information display and function the same as a warning lamp but do not display when you start your vehicle. Anti-Lock Braking System


If it lights when you are driving, this indicates a malfunction. You will continue to have normal


braking (without anti-lock braking system) unless the brake system warning lamp also lights. Have the system checked by an authorized dealer. Battery


If it lights while driving, this indicates a malfunction. Switch off all unnecessary electrical


equipment and have the system checked by an authorized dealer immediately. Brake System


Lights when you engage the parking brake with the ignition on.


If it lights when you are driving, check that you do not have the parking brake engaged. If you do not have the parking brake engaged, this indicates low brake fluid level or a brake system malfunction. Have the system checked immediately by an authorized dealer.


WARNING


Driving your vehicle with the warning lamp on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop your vehicle. Have your vehicle checked by your authorized dealer immediately. Driving extended distances with the parking brake engaged can cause brake failure and the risk of personal injury.


Cruise Control (If Equipped)


Lights when you switch on this feature.


Direction Indicator


Lights when you switch on the left or right direction indicator or hazard warning flasher. If the


indicators stay on or flash faster, check for a burned out bulb. See Changing a Bulb (page 222). Door Ajar


Displays when the ignition is on and any door is not completely closed.


Engine and Motor Coolant Temperature


Lights when the engine or motor coolant temperature is high. Stop the vehicle as soon as


possible, switch off the engine and let cool. Engine Oil


If it lights with the engine running or while you are driving, this indicates a malfunction. Stop your vehicle as soon as it is safe to do so and switch off the engine. Check the engine oil level. See Engine Oil Check (page 212). Note: Do not resume your journey if it lights despite the level being correct. Have the system checked by an authorized dealer immediately. EV Now


Lights when you select this feature on. See Hybrid Electric Vehicle (page 129).


84


C-MAX (CCG)


E144522E71340E144814 Instrument Cluster


EV Later


Low Fuel Level


Lights when you select this feature on. See Hybrid Electric Vehicle (page 129).


Lights when the fuel level is low or the fuel tank is nearly empty. Refuel as soon as possible.


Fasten Safety Belt


It will light and a tone will sound to remind you to fasten your safety belt. See Safety Belt


Minder (page 30). Front Airbag


If it fails to light when you start your vehicle, continues to flash or remains on, this indicates a


malfunction. Have the system checked by an authorized dealer. Front Fog Lamps (If Equipped)


Lights when you switch the front fog lamps on.


High Beam


Lights when you switch the high beam headlamps on. It will flash when you use the headlamp


flasher. Liftgate Ajar


Lights when the liftgate is not completely closed.


Low Battery (If Equipped)


Lights when the battery level is low. You may also see a message suggesting you reduce


your usage of the climate system.


Low Tire Pressure Warning


Lights when your tire pressure is low. If the lamp remains on with the engine running or when driving, check your tire pressure


as soon as possible. It also lights momentarily when you switch on the ignition to confirm the lamp is functional. If it does not light when you switch on the ignition, or begins to flash at any time, have the system checked by an authorized dealer. Overdrive Cancel and Grade Assist (If Equipped)


Lights when the overdrive function in the transmission turns off and the grade assist


turns on. Parking Lamps


Lights when you switch the parking lamps on.


Powertrain Fault


Lights when the system detects a powertrain or high-voltage charge system fault. If the


indicator stays on or continues to come on, contact an authorized dealer as soon as possible.


85


C-MAX (CCG)


E151263E162453E144691E162456 Instrument Cluster


Normally, the service engine soon light will stay on until you switch on the engine, then turn itself off if no malfunctions are present. However, if after 15 seconds the service engine soon light blinks eight times, it means that the vehicle is not ready for Inspection and Maintenance testing. See Emission Control System (page 143). Stability Control


Lights when the system is active. If it remains on or does not light when you switch the ignition on,


this indicates a malfunction. During a malfunction, the system will turn off. Have the system checked by an authorized dealer immediately. See Using Stability Control (page 161). Stability Control Off


Lights when you switch the system off. It will go out when you switch the system back on or when you switch the ignition off. See Using Stability Control (page 161). Stop Safely


Indicates an electrical component fault or failure that will cause the vehicle to


shutdown or enter into a limited operating mode. A message may also display. Vehicle Plugged in (If Equipped)


Lights after you plug in your vehicle. A corresponding message may display after


attempting to start the vehicle.


Note: If your vehicle detects certain faults, it will not allow you to operate the accelerator pedal. If this happens, press the brake pedal and release it. This will activate limp home vehicle operation. In limp home vehicle operation, your vehicle will accelerate in a controlled manner up to a maximum speed of 35 mph (56 km/h) on a flat surface. If you apply the brake pedal or move the transmission to neutral (N) you can override your vehicle’s acceleration. Ready to Drive


Lights after your switch your vehicle on and it is ready to drive. A corresponding message may


display stating ready to drive. Service Engine Soon


If the service engine soon indicator light stays on after you switch on the engine, this


indicates that the On-Board Diagnostics system (OBD) has detected a malfunction of the vehicle emissions control system. Refer to On-Board diagnostics (OBD) in the Fuel and Refueling chapter for more information about having your vehicle serviced. See Emission Control System (page 143). If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately. Note: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter or other vehicle components. The service engine soon indicator lights when you first switch on the ignition prior to engine start to check the bulb and to indicate whether the vehicle is ready for Inspection and Maintenance testing.


86


C-MAX (CCG)


E144692E138639E144693E144694 Instrument Cluster


AUDIBLE WARNINGS AND INDICATORS Key in Ignition Warning Chime Sounds when you open the driver's door and you have left the key in the ignition with it in the off or accessory position. Engine On Warning Chime A warning chime will sound when any door is opened if the vehicle exceeds a relatively low speed. Keyless Warning Alert (If Equipped) Sounds the horn twice when you exit the vehicle and the keyless vehicle is in RUN, indicating the vehicle is still on. Headlamps On Warning Chime Sounds when you remove the key from the ignition and open the driver's door and you have left the headlamps or parking lamps on. Parking Brake On Warning Chime Sounds when you have left the parking brake on and drive your vehicle. If the warning chime remains on after you have released the parking brake, have the system checked by your authorized dealer immediately. Automatic Transmission Warning Chime Sounds when you have not moved the transmission selector lever to position P. A message will be shown in the display.


87


C-MAX (CCG)


Information Displays


• Press the left arrow button to exit a


menu.


• Press and hold the left arrow button at


any time to return to the main menu display (escape button).


• Press the OK button to choose and


confirm settings or messages.


Main menu From the main menu bar on the left side of the information display, you can choose from the following categories:


Display Mode


Trip 1 & 2


Fuel Economy


Information


Settings


Scroll up or down to highlight one of the categories, then press the right arrow key or OK to enter into that category. Press the left arrow key as needed to exit back to the main menu. Display Mode


Use the up and down arrow buttons to choose between the following display options.


Note: The cluster will remember menu level 2 state when the individual key state is changed from RUN to the OFF position.


GENERAL INFORMATION


WARNING


Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving


Various systems on your vehicle can be controlled using the information display controls on the steering wheel. Corresponding information is displayed in the information display. Information Display Controls


• Press the up and down arrow buttons


to scroll through and highlight the options within a menu.


• Press the right arrow button to enter a


sub-menu.


88


C-MAX (CCG)


E162394E144639E138660E144640E144642E100023E144639 Information Displays


Display Mode


Menu level 3


Menu level 4


Menu level 5


Menu level 2
Vehicle Range


(Estimated Range + Battery Gauge + Fuel


Gauge)


Inform


(Avg Fuel Economy + Battery Gauge + Fuel


Gauge)


Instantaneous Fuel


Battery Display


Help


Instantaneous Fuel


Battery Display


Enlighten


(Power + Avg Fuel Economy + Battery Gauge + Fuel Gauge)


Help


Instantaneous Fuel


Battery Display


Help


Instantaneous Fuel


Battery Display


Engage


(Split Power + Avg Fuel Economy +


Battery Gauge + Fuel


Gauge)


Empower


Instantaneous Fuel


Help


89


C-MAX (CCG)



Regen Active Charge Assist Charge Level


Help — —


Regen Active Charge Assist Charge Level


Help — —


Regen Active Charge Assist Charge Level


Help — —


Regen Active Charge Assist Charge Level


Help — —



Apply to all screens?


Yes / No


— —


Apply to all screens?


Yes / No


— —


Apply to all screens?


Yes / No


— —


Apply to all screens?


Yes / No


— —


(Power (with engine on/off threshold) + Avg Fuel Economy + Battery Gauge + Fuel


Gauge)


MyView


(MyView + Battery Gauge + Fuel Gauge)


Information Displays


Display Mode


Battery Display


Help


Regen Active Charge Assist Charge Level


Help —


Apply to all screens?


Yes / No



Change MyView


Vehicle Range


Vehicle Range


Avg Fuel Power


Split Power


Power + Threshold Tach rpm x 1000
Tach rpm x 1000 +


Avg mpg


Avg Fuel Inst. Fuel


Coolant Temp Accessory Power


Trip 1
Trip 2


Accessory Power


Fuel History


Trip 1
Trip 2


Coach Blank


Display Mode (cont'd)


Menu level 4
Fuel History


Coach Blank


Regen Active Charge Assist Charge Level


Help —


Menu level 5


— — —


Apply to all screens?


Yes / No



Menu level 2
MyView (cont'd) (MyView + Battery Gauge + Fuel Gauge)


Menu level 3
Change MyView


(cont'd)


Battery Display


Help


90


C-MAX (CCG)


Information Displays


Display Mode (cont'd)


Battery Display


Help


Regen Active Charge Assist Charge Level


Help —


Apply to all screens?


Yes / No



Energy Use (Energi


only) Auto EV


(consumption gauge


+ climate power


gauge + battery gauge


+ fuel gauge)


EV Now


(consumption gauge with budget cup + climate power gauge


+ engine enable + battery gauge + fuel


gauge) EV Later


(consumption gauge


+ climate power


gauge + battery gauge


+ fuel gauge)


Vehicle Range Indicates the estimated distance the vehicle will travel with the energy currently available. For Hybrid, the vehicle range estimate is based on the fuel remaining in the gasoline tank. For Energi, the total estimated range equals the range available in Hybrid Mode fueled by gasoline, plus the electric range available in Plug-in Power Mode. Changes in driving pattern may cause the values to vary. Inform Inform shows the fuel level, battery display and average fuel economy, with options available for the Battery Display and an Instantaneous Fuel Economy gauge. When the vehicle is operating on battery power only with the engine off, EV is displayed.


Enlighten Enlighten displays power demand in addition to the typical information and options from Inform. The Instantaneous Fuel Economy gauge will be displayed by default. When the vehicle is operating on battery power only with the engine off, EV is displayed and the gauge fill is shown in blue. When both the engine and high voltage battery are providing power the gauge fill is white. Engage Engage replaces the power demand gauge from Enlighten with separate gauges for engine power and high voltage battery power. The engine power gauge fill is white and the high voltage battery power gauge fill is blue. When the vehicle is operating on battery power only with the engine off, EV is displayed.


91


C-MAX (CCG)


Information Displays


Unique content available in MyView: • Accessory Power— Indicates electrical


power demands from your vehicle’s accessory systems. Accessories use power but do not contribute to propelling the vehicle. The gauge separately displays power demand in kilowatts (kW) for climate and other accessories.


Climate includes the power being used by high voltage climate control components such as the electric A/C compressor and the electric heater (Energi vehicles only) Other includes all power being used by the low voltage accessories (cabin fans, headlights, heated seats, etc.). • Coolant Temp – Indicates engine coolant temperature. At normal operating temperature, the level indicator will be white and will be in the normal range (between H and C). If the engine coolant temperature exceeds the normal range, the level indicator will change to red to indicate that the engine is overheating. Stop the vehicle as soon as safely possible, turn off the vehicle and let the engine cool.


The thermometer indicator next to the gauge will illuminate in blue or white to indicate the following (not available for Energi vehicles): •


Blue thermometer - This indicates that the hybrid system is not warm enough to allow EV operation. The gasoline engine will typically run continuously when the indicator is blue.


Empower Empower adds an engine on/off threshold to the power demand gauge from Enlighten. The threshold is shown as a blue double outline. The gauge is designed to show you how close you are to the gasoline engine on/off threshold and how much power you are requesting based on how far you press the accelerator pedal. When power demand is below the threshold the vehicle is operating on battery power only with the engine off, EV is displayed and the gauge fill is shown in blue. When power demand exceeds the threshold both the engine and the high voltage battery provide power and the gauge fill is white. When power demand surpasses the amber indicator, this level of demand and associated fuel economy are shown in amber. Note: You can reset your average fuel economy by pressing and holding the OK button on the left hand steering wheel controls. MyView You can choose what to display in this view. Selecting Change MyView in the options menu allows you to scroll through two columns of content choices. • Press the up or down arrow to view


content.


• Use the right and left arrows to move between the left column content and the middle column content. The right column is reserved for the Battery Gauge and the Fuel Gauge.



Once you have your desired content showing in each column then press OK to save. This becomes your new MyView screen.


92


C-MAX (CCG)


Information Displays


• Consumption Gauge: Your current


present energy use per distance traveled is represented by the white line that moves up and down in the gauge. A higher line means you are using more energy (lower is better). Your energy use includes input from the accelerator pedal as well as the accessories, such as Climate Control.


When operating in EV Now a blue cup shape is shown around the gauge. This represents the maximum energy usage you can maintain in order to achieve the estimated electric range shown on the battery gauge at the time of entering EV now. Keep your current energy use mostly within the cup while driving and you should achieve your electric range estimate. • Climate Power Gauge: Indicates high voltage electrical power demand from you vehicle’s high voltage climate control components such as the electric A/C compressor and the electric heater. These components use power but do not contribute to propelling the vehicle. The gauge displays power demand in kilowatts (kW). Trip 1 & 2


Use the arrow buttons to choose between the following.


Note: During silent key start mode, the thermometer indicator will be blue, but the gasoline engine will not run. This is the result of the vehicle computer allowing the engine to be cooler during the silent key start period. This is normal operation and does not indicate a problem with your vehicle. After the first engine start the indicator will turn white when the gasoline engine is warm enough to turn off. • White thermometer - This indicates


that the hybrid system is warm enough to allow EV operation. If the vehicle operates on battery power long enough, it is possible that the gasoline engine may need to run to keep the system warm. In this case, the thermometer indicator will revert back to blue. Tach rpm x 1000 — When the gasoline engine is running, the tachometer gauge displays the engine speed in revolutions per minute (RPM). When the vehicle is operating on battery power only with the engine off, EV is displayed and the tachometer is greyed out.



Note: The trip data, and average fuel economy cannot be reset in MyView. Energy Use (Energi only) Energy Use provides an energy use gauge and a climate power gauge in addition to fuel level and battery display. When you select EV Now operation this screen will automatically be shown. You can press OK to enable the engine when viewing this screen during EV Now operation. See Hybrid Electric Vehicle (page 129). Note: Pressing OK resets the odometer and timer.


93


C-MAX (CCG)


E138660 Menu level 2
Trip 1 & Trip 2


(Trip Data+Battery Gauge+Fuel Gauge)


Information Displays


Trip 1 & 2


Menu level 3


Menu level 4


Menu level 5


Standard


Enhanced


Battery Display


— — — — — —


— — — — — —


Regen Active Charge Assist Charge Level


Help —


Apply to all screens?


Yes / No




Help


• •


Standard - Elapsed trip time, Trip distance and EV distance •


Elapsed trip time — timer stops when the vehicle is turned off and restarts when the vehicle is restarted. Trip distance — shows the accumulated trip distance. EV distance — shows the distance traveled while operating on battery power only with the engine off.


Enhanced - Standard options plus, Average fuel economy, Estimated amount of fuel consumed and Estimated amount of electricity consumed (Energi only) • Average fuel economy - is continuously averaged since the last reset. For Energi vehicles both hybrid and plug-in power mode operation will be included in the calculation. Estimated amount of fuel consumed — shows the amount of fuel used for a given trip. Estimated amount of electricity consumed — shows the amount of plug-in electricity used for a given trip.




Fuel Economy


Use the arrow buttons to choose the desired energy display.


94


C-MAX (CCG)


E144640 Menu level 2
Fuel History


(Instantaneous Fuel


Economy + Fuel Economy History +


Avg Fuel


Economy+Battery Gauge+Fuel Gauge)


Coach


(Coach+Battery


Gauge+Fuel Gauge)


Information Displays


Fuel Economy


Menu level 3
Interval Time Battery Display


Help


Battery Display


Help


Menu level 4


Menu level 5


1, 2, 6 min. Intervals



Regen Active Charge Assist Charge Level


Help —


Regen Active Charge Assist Charge Level


Help —


Apply to all screens?


Yes / No



Apply to all screens?


Yes / No




Fuel History: This view from left to right starts with the instantaneous fuel economy gauge and adds historical fuel economy data. The data is represented as an average for time intervals of either 1, 2 or 6 minutes, with the left most interval being the most recent. Total time for the 5 intervals is shown at the bottom of the view. Intervals shown in grey color are from the previous drive.


Note: You can reset your average fuel economy by pressing and holding the OK button on the left hand steering wheel controls. • Coach: This view provides a comparison of your recent Acceleration, Braking and Cruising behavior to what is recommended for most efficient use of energy under present conditions. The horizontal bars fill from left to right with best behavior (and Blue color) shown as at least half full. When the bars are less than half full, the color is Amber, suggesting that a change in behavior is needed to achieve better energy efficiency.


Note: Fuel economy is not always a measure of appropriate driving behavior. For example, when driving uphill and maintaining an appropriate speed, your instant fuel economy may not be good (losing leaves) but the Coach may show a blue bar for Acceleration or Cruising.


Info


In this mode, you can view different vehicle system information and perform a


system check.


95


C-MAX (CCG)


E144642 Information Displays


Warnings


Tutorial


MyKey


System Check


Settings


Information


Displays the number of warnings that need immediate attention in red. You can only view the warnings from the System Check menu. View them immediately by pressing OK and then OK again to enter system check. Use the up/down arrows to scroll through the warn- ings. Displays a number of different system tutorials. Use the up/down arrows to scroll through the tutorials. Then press OK to view. MyKeys (Number of MyKeys programmed) MyKey Miles (km) (Distance traveled using a programmed MyKey) Admin Keys (Number of admin keys) All active warnings will display first if applicable. The system check menu may appear different based upon equipment options and current vehicle status. Use the up/down arrow buttons to scroll through the list.


Note: Some items are optional and may not appear.


In this mode, you can configure different driver setting choices.


Menu level 2
Driver Assist


Menu level 3
Traction Control ECO Cruise


Hill Start Assist


EV + Mode Rear Park Aid


Settings


Menu level 4
On or Off


Menu level 5


On (default on key cycle) or Off On (default on key cycle) or Off On or Off On (default on key cycle) or Off


96





— —


C-MAX (CCG)


E100023 Information Displays


Vehicle


Lighting


Remote Start


Settings


Auto Light Rain Home Light Climate Control


On or Off


Select time interval


Heater – A/C


Front Defrost Rear Defrost Driver Seat


Passenger Seat


Auto or Last


Settings Auto or Off Auto or Off Auto or Off Auto or Off


Duration Quiet Start System


5, 10 or 15 minutes


On or Off


Enable or Disable


Note: Some MyKey items will only appear if a MyKey is set.


Settings (cont’d)


Menu level 2
Vehicle (cont’d) MyKey


Menu level 3
Tire Mobility Kit Create MyKey


Traction Control


Max Speed


Speed Minder


Volume Limiter Clear MyKeys


Display


Language


Menu level 5


— —





— —



Menu level 4
Select number of years Hold OK to Create MyKey Always On or User Selectable Choose desired speed or off Choose desired speed or off On or Off Hold OK to Clear All MyKeys Select the desired language


97


C-MAX (CCG)


Information Displays


Units


Settings (cont’d)


Distance


Brake Coach Display Driving History


Temperature


On or Off


Hold OK to Reset


Select the desired units of measure Fahrenheit (°F) or


Celsius (°C)




INFORMATION MESSAGES Note: Depending on the vehicle options equipped with your vehicle, not all of the messages will display or be available. Certain messages may be abbreviated or shortened depending upon which cluster type you have.


Press the OK button to acknowledge and remove some messages from the information display. Other messages will be removed automatically after a short time. Certain messages need to be confirmed before you can access the menus.


AdvanceTrac® Message


Service AdvanceTrac


Action


Displayed when the system has detected a condition that requires service. Contact your authorized dealer as soon as


possible.


98


C-MAX (CCG)


E130248 Information Displays


Alarm


Message


Action


To Stop Alarm, Start


Vehicle


Displays when the alarm has been triggered due to unauthor-


ized entry. See Anti-Theft Alarm (page 64).


Battery and Charging System (High Voltage)


Message


Is Vehicle Plugged-In?


Stop Safely Now


Action


Displays when confirmation is needed that the vehicle is


unplugged before a start is allowed. You must make sure the vehicle is unplugged and respond to the message prompt


before starting your vehicle.


Displays when the stop safety hazard warning lamp is illumin- ated. This indicates an electrical component fault/failure that


will cause the vehicle to shut down or enter into limited


operating mode.


Ready to Drive


Displays when the vehicle is ready to drive.


Unplug Prior to Starting


Vehicle


Check Battery Charge


Engine On


Displays when the vehicle detects it is still plugged and the


power is activated.


Displays when battery charge level is low.


Displays when the engine is on.


Doors


Message X Door Ajar


Action


Displays when the door(s) listed is not completely closed and


the vehicle is moving.


Displays when the door(s) listed is not completely closed.


Liftgate Ajar


Displays when the liftgate is not completely closed.


99


C-MAX (CCG)


Information Displays


Fuel


Message


Action


Fuel Level LOW


Displayed as an early reminder of a low fuel condition.


Check Fuel Fill Inlet


Fuel Freshness


Fuel Door Opening


Fuel Door Open


Displayed when the fuel fill inlet may not be properly closed. Displays when EV functionality is disabled and the engine is running to maintain fuel freshness. See Fuel Quality (page


136).


Displays when the fuel door is opening.


Displays when the fuel door is opened and the vehicle is ready


to be refueled.


Close Fuel Door


Displays when the fuel door listed is not closed.


Refuel Error See Manual


Displays when there is a vehicle error and it cannot be refueled.


Hill Start Assist


Message


Action


Hill Start Assist Not


Available


Displays when hill start assist is not available. Contact your


authorized dealer. See Hill Start Assist (page 157).


Hill Start Assist Active Hill Start Assist OFF


Displays when hill start assist is active.


Displays when hill start assist is off.


Keys and Intelligent Access


Message


Starting System Fault


Action


This message is displayed when there is a problem with your


vehicle’s starting system. See your authorized dealer for


service.


Key Inside Vehicle


Key Not Inside Car


No Key Detected


Displays to remind you that the key is in the luggage compartment. See Keyless Starting (page 124).


Displays if the key is not detected by the system. See Keyless


Starting (page 124).


Displayed if the key is not detected by the system. See


Keyless Starting (page 124).


100


C-MAX (CCG)


Information Displays


Message


Restart Now or Key is


Needed


Accessory Power Active


Press Brake to Start

Loading...
x