2010 Chevrolet Camaro Owners Manual

Download PDF Manual
5-4 Lighting The vehicle has a light sensor located on the top of the instrument panel. Do not cover this sensor or the system will come on whenever the ignition is on. The system may also turn on the headlamps when driving through a parking garage, heavy overcast weather, or a tunnel. This is normal. There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system will only be affected when the light sensor sees a change in lighting lasting longer than the delay. If the vehicle is started in a dark garage, the automatic headlamp system comes on immediately. If it is light outside when the vehicle leaves the garage, there will be a slight delay before the automatic headlamp system changes to the DRL. During that delay, the instrument panel cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position. See Instrument Panel Illumination Control on page 5-5. Hazard Warning Flashers | Hazard Warning Flasher: Press this button located on the instrument panel near the audio system, to make the front and rear turn signal lamps ﬂash on and off. This warns others that you are having trouble. Press again to turn the ﬂashers off. Turn and Lane-Change Signals An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to ﬂash to signal a lane change. Hold it there until the lane change is completed. If the lever is brieﬂy pressed and released, the turn signal ﬂashes three times. The lever returns to its starting position whenever it is released. If after signaling a turn or lane change the arrow ﬂashes rapidly or does not come on, a signal bulb might be burned out. Have the bulbs replaced. If the bulb is not burned out, check the fuse. See Electrical System Overload on page 9-41. Front Fog Lamps For vehicles with front fog lamps, the button is located on the exterior lamp control, on the outboard side of the steering wheel. The ignition must be turned to ON/RUN to turn on the fog lamps. # : Press to turn the fog lamps on or off. An indicator light on the instrument panel cluster comes on when the fog lamps are on. The fog lamps come on together with the parking and sidemarker lamps. If the high-beam headlamps are turned on, the fog lamps will turn off. If the high-beam headlamps are turned off, the fog lamps will turn back on again. For vehicles with High Intensity Discharge (HID) headlamps, the Daytime Running Lamps (DRL) replace the fog lamps. Some localities have laws that require the headlamps to be on along with the fog lamps. Lighting 5-5 Interior Lighting Instrument Panel Illumination Control This feature controls the brightness of the instrument panel lights. The thumbwheel is located next to the exterior lamp control. D (Instrument Panel Brightness): Turn the thumbwheel up or down to brighten or dim the instrument panel lights. 5-6 Lighting Dome Lamps The dome lamp buttons are located in the overhead console. To change the settings, press the following: ( (Off): Turns the lamp off, even when a door is open. 1 (Door): The lamp comes on automatically when a door is opened. ' (On): Turns the dome lamp on. Lighting Features Entry Lighting The lamps inside the vehicle come on when any door is opened. They stay on about 20 seconds and when all of the doors have been closed or the ignition is turned to ON/RUN they gradually fade out. They also come on when the unlock symbol button is pressed on the Remote Keyless Entry (RKE) system transmitter. The lamps inside the vehicle stay on for about 20 seconds after the key is removed from the ignition to provide light as you exit. Theater Dimming This feature allows for a three to ﬁve second fade out of the courtesy lamps instead of immediately turning off. Battery Load Management The vehicle has Electric Power Management (EPM) that estimates the battery’s temperature and state of charge. It then adjusts the voltage for best performance and extended life of the battery. When the battery’s state of charge is low, the voltage is raised slightly to quickly bring the charge back up. When the state of charge is high, the voltage is lowered slightly to prevent overcharging. If the vehicle has a voltmeter gage or a voltage display on the Driver Information Center (DIC), you may see the voltage move up or down. This is normal. If there is a problem, an alert will be displayed. The battery can be discharged at idle if the electrical loads are very high. This is true for all vehicles. This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads. Lighting 5-7 A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery. It does this by balancing the generator’s output and the vehicle’s electrical needs. It can increase engine idle speed to generate more power, whenever needed. It can temporarily reduce the power demands of some accessories. Normally, these actions occur in steps or levels, without being noticeable. In rare cases at the highest levels of corrective action, this action may be noticeable to the driver. If so, a Driver Information Center (DIC) message might be displayed, such as BATTERY SAVER ACTIVE, BATTERY VOLTAGE LOW, or LOW BATTERY. If one of these messages display, it is recommended that the driver reduce the electrical loads as much as possible. See Driver Information Center (DIC) on page 4-27. Battery Power Protection This feature shuts off the dome lamps if they are left on for more than 10 minutes when the ignition is in LOCK/OFF. This helps to prevent the battery from running down. 5-8 Lighting ✍ NOTES Infotainment System Introduction Introduction ..........................6-1 Theft-Deterrent Feature ..........6-2 Overview ..............................6-2 Operation .............................6-4 Radio AM-FM Radio .......................6-8 Satellite Radio .....................6-10 Radio Reception ..................6-13 Backglass Antenna ..............6-13 Satellite Radio Antenna ........6-14 Audio Players CD Player ..........................6-14 Auxiliary Devices .................6-16 Phone Bluetooth (Overview) ............6-22 Bluetooth (Infotainment Controls) ........6-23 Bluetooth (Voice Recognition) ............6-26 Introduction Read the following pages to become familiar with the infotainment system features. { WARNING Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving. This system provides access to many audio and non audio listings. To minimize taking your eyes off the road while driving, do the following while the vehicle is parked: • Become familiar with the operation and controls of the audio system. • Set up the tone, speaker adjustments, and preset radio stations. Infotainment System 6-1 For more information, see Defensive Driving on page 8-2. Notice: Contact your dealer/retailer before adding any equipment. Adding audio or communication equipment could interfere with the operation of the vehicle’s engine, radio, or other systems, and could damage them. Follow federal rules covering mobile radio and telephone equipment. The vehicle has Retained Accessory Power (RAP). With RAP, the infotainment system can play even after the ignition is turned off. See Retained Accessory Power (RAP) on page 8-19 for more information. 6-2 Infotainment System Theft-Deterrent Feature The theft-deterrent feature works by learning a portion of the Vehicle Identiﬁcation Number (VIN) to the infotainment system. The system does not operate if it is stolen or moved to a different vehicle. Overview A. O /VOL • Press: Turns the system on or off. • Turn: Adjusts the volume. B. INFO • Radio: Shows available information about the current station. • CD/MP3: Shows available information about the current track. C. Buttons 1 - 6 • Radio: Saves and selects favorite stations. D. FAV • Radio: Opens the favorites list. E. MENU/SELECT • Press: Opens the menus and selects menu items. • Turn: Highlights menu items or sets values while in a menu. Manually selects radio stations while listening to the radio. F. RADIO/BAND • Changes the band while listening to the radio. • Selects the radio when listening to a different audio source. Infotainment System 6-3 G. Z CD Eject • Removes CD from slot. H. CD/AUX • Selects between the CD player or a connected external audio source. I. PHONE L. l SEEK • Radio: Seeks the next station. • CD: Selects the next track or fast forwards within a track. M. CONFIG • Opens the settings menu. • Opens the phone main menu. • Mutes the audio system. N. TONE • Opens the tone menu. J. g SEEK O. 0 BACK • Radio: Seeks the previous station. • CD: Selects the previous track or rewinds within a track. • Menu: Moves one level back. • Character Input: Deletes the last character. K. CD Slot • Insert a CD. 6-4 Infotainment System Operation Controls The infotainment system is operated by using the pushbuttons, multifunction knobs, and menus that are shown on the display, and steering wheel controls, if equipped. Turning the System On or Off O VOL (Power/Volume): Press to turn the system on and off. Automatic Off If the infotainment system has been turned on after the ignition is turned off, the system turns off automatically after ten minutes. Volume Control O VOL (Power/Volume): Turn to adjust the volume. PHONE: For vehicles with OnStar®, press and hold PHONE to mute the infotainment system. Press and hold PHONE again, or turn the O VOL to cancel mute. For vehicles without OnStar®, press PHONE to mute the infotainment system. Press PHONE again, or turn the O VOL to cancel mute. Menu System Controls The MENU/SELECT knob and the 0 BACK button are used to navigate the menu system. MENU/SELECT: Press to: • Enter the menu system. • Select or activate the highlighted menu option. • Conﬁrm a set value. • Switch a system setting on or off. Turn to: • Highlight a menu option. • Select a value. 0 BACK: Press to: • Exit a menu. • Return from a submenu screen to the previous menu screen. • Delete the last character in a sequence. Selecting a Menu Option Activating a Setting Turning a Function On or Off Infotainment System 6-5 1. Turn the MENU/SELECT knob to move the highlighted bar. 1. Turn the MENU/SELECT knob to highlight the setting. 1. Turn the MENU/SELECT knob to highlight the function. 2. Press the MENU/SELECT knob to select the highlighted option. 2. Press the MENU/SELECT knob to activate the setting. 2. Press the MENU/SELECT knob to turn the function on or off. Submenus Setting a Value Entering a Character Sequence An arrow on the right-hand edge of the menu indicates that it has a submenu with other options. 1. Turn the MENU/SELECT knob to change the current value of the setting. 2. Press the MENU/SELECT knob to conﬁrm the setting. 1. Turn the MENU/SELECT knob to highlight the character. 2. Press the MENU/SELECT knob to select the character. 6-6 Infotainment System Press the 0 BACK button to delete the last character or press and hold 0 BACK to delete the entire character sequence. Audio Settings The audio settings can be set for each radio band and each audio player source. To adjust the audio setting, press the TONE button and select the audio setting. Press the 0 BACK button to go back to the Tone Settings menu. To quickly reset an audio setting value to 0: 1. Highlight the option. 2. Press and hold the MENU/SELECT knob until the value changes to 0. Adjusting the Treble, Midrange, and Bass Adjusting the EQ (Equalizer) For vehicles that have an equalizer: 1. Select Treble, Midrange, or Bass. 2. Select the value. Adjusting the Fader and Balance 1. Select EQ. 2. Select the setting. 1. Select Fader or Balance. 2. Select the value. System Settings Conﬁguring the Number of Favorite Pages To conﬁgure the number of available favorite pages: 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Radio Favorites. 4. Select the number of available favorite pages. 5. Press the 0 BACK button to go back to the System Conﬁguration menu. Auto Volume The auto volume feature automatically adjusts the radio volume to compensate for road and wind noise as the vehicle speeds up or slows down, so that the volume level is consistent The level of volume compensation can be selected, or the auto volume feature can be turned off. 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Auto Volume. 4. Select the setting 5. Press the 0 BACK button to go back to the System Conﬁguration menu. Infotainment System 6-7 Maximum Startup Volume The maximum volume played when the radio is ﬁrst turned on can be set. 1. Press the CONFIG button. 2. Select Radio Settings. 3. Select Maximum Startup Volume. 4. Select the setting 5. Press the 0 BACK button to go back to the System Conﬁguration menu. 6-8 Infotainment System Radio AM-FM Radio Control Buttons The buttons used to control the radio are: RADIO/BAND: Press to turn the radio on and choose between AM, FM, and XM™, if equipped. g SEEK/ l SEEK: Press to search for stations. FAV: Press to open the favorites list. 1-6: Press to select preset stations. MENU/SELECT: Turn to manually search for stations. RDS (Radio Data System) The radio may have RDS. The RDS feature is available for use only on FM stations that broadcast RDS information. This feature only works when the information from the radio station is available. In rare cases, a radio station could broadcast incorrect information that causes the radio features to work improperly. If this happens, contact the radio station. While the radio is tuned to an FM-RDS station, the station name or call letters display. Radio Menus Radio menus are available for AM, FM and XM, if equipped. Press the MENU/SELECT knob to open the main radio menu for that frequency. Selecting a Band Press the RADIO/BAND button to choose AM, FM, or XM™, if equipped. The last station that was playing starts playing again. Selecting a Station Seek Tuning Brieﬂy press g SEEK or l SEEK to automatically search for the next available station. If a station is not found, the radio switches to a more sensitive search level. If a station still is not found, the frequency that was last active begins to play. Press and hold g SEEK or l SEEK until the station on the display is reached, then release the button. Manual Tuning Turn the MENU/SELECT knob to select the frequency on the display. Favorites List 1. Press the MENU/SELECT knob. 2. Select Favorites List. 3. Select the station. Station Lists 1. Press the MENU/SELECT knob. 2. Select AM or FM Station List. All receivable stations in the current reception area are displayed. If no station list has been created an automatic station search is done. 3. Select the station. Updating Station & Category Lists If stations stored in the station list can no longer be received. 1. Press the MENU/SELECT knob. 2. Select Update AM or FM Station List, if the station stored in the station list are no longer received. A station search will be completed and the ﬁrst station in the updated list will play. To cancel the station search, press the MENU/SELECT knob. Category Lists Infotainment System 6-9 The system stores the RDS stations, sorted by program type, in the FM category list. To search for a programing type determined by station: 1. Select FM category list. A list of all programing types available displays. 2. Select the programing type. A list of stations that transmit programming of the selected type displays. 3. Select the station. The category lists are updated when the corresponding station lists are updated. Most stations that broadcast an RDS PTY code specify the type of programming transmitted. Some stations change the PTY code depending on the content. 6-10 Infotainment System Storing and Retrieving Favorites Stations from all bands can be stored in the favorite lists in any order. Up to six stations can be stored in each favorite page and the number of available favorite pages can be set. Storing a Station as a Favorite To store the station to a position in the list, press the corresponding numeric button 1-6 until the station can be heard again. Retrieving Stations Press the FAV button to open a favorite page or to switch to another favorite page. Brieﬂy press one of the 1-6 buttons to retrieve the station. Satellite Radio Vehicles with an XM™ Satellite Radio tuner and a valid XM Satellite Radio subscription can receive XM programming. XM Satellite Radio Service XM is a satellite radio service that is based in the 48 contiguous United States and 10 Canadian provinces. XM Satellite Radio has a wide variety of programming and commercial-free music, coast-to-coast, and in digital-quality sound. During your trial or when you subscribe, you will get unlimited access to XM Radio Online for when you are not in the vehicle. A service fee is required to receive the XM service. For more information, contact XM at www.xmradio.com or call 1-800-929-2100 in the U.S. and www.xmradio.ca or call 1-877-438-9677 in Canada. Control Buttons The buttons used to control the XM radio are: RADIO/BAND: Press to turn the radio on and choose between AM, FM, and XM™, if equipped. g SEEK / l SEEK: Press to search for stations. FAV: Press to open the favorites list. 1-6: Press to select preset stations. MENU/SELECT: Turn to search for stations. Selecting the XM Band Press the RADIO/BAND button to choose between the AM, FM, and XM bands. The last station played in that band begins to play when that band is selected. XM Categories XM stations are organized in categories. Removing or Adding Categories 1. Press the CONFIG button. 2. Select XM Categories. 3. Turn the MENU/SELECT knob to highlight the category. 4. Press the MENU/SELECT knob to remove or add the category. Selecting an XM Station XM stations can be selected by using g SEEK, l SEEK, the MENU/SELECT knob, or the menu system. Infotainment System 6-11 To select an XM station using g SEEK or l SEEK, do one of the following: • Press and release g SEEK or l SEEK to go to the previous or next station. • Press and hold g SEEK or l SEEK to scroll through the previous or next stations until the station is reached. To select an XM station using the MENU/SELECT knob: 1. Turn the MENU/SELECT knob to highlight an XM station. 2. Press the MENU/SELECT knob to select the station, or leave the station highlighted. To select a station using the menu: 1. Press the MENU/SELECT knob. 2. Select XM Stations List. 3. Select the station. Selecting a Station by Category 1. Press the MENU/SELECT knob. 2. Select XM Category List. A list of all programing types available displays. 3. Select the programing type. 4. Select the station. Storing and Retrieving Favorites Stations from all bands can be stored in any order in the favorite pages. Up to six stations can be stored in each favorite page and the number of available favorite pages can be set. Storing a Station as a Favorite To store the station to a position in the list, press and hold the corresponding 1-6 button until the station can be heard again. 6-12 Infotainment System Retrieving stations Press the FAV button to open a favorite page or to switch to another favorite page. Brieﬂy press one of the 1-6 buttons to retrieve the station. XM Messages XL (Explicit Language Channels): These channels, or any others, can be blocked by request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code is being updated, no action is required. Loading XM: The audio system is acquiring and processing audio and text data, no action is needed. Channel Off Air: This channel is not currently in service. Channel Unauth: This channel is blocked or cannot be received with the XM Subscription package. Channel Unavail: This previously assigned channel is no longer assigned. No Artist Info: No artist information is available. No Title Info: No song title information is available. No CAT Info: No category information is available. No Information: No text or informational messages are available. No XM Signal: The vehicle may be in a location that where the XM signal is being blocked. When the vehicle is moved, the signal should return. CAT Not Found: There are no channels available for the selected category. XM Theftlocked: The XM receiver in the vehicle may have been in another vehicle. XM receivers cannot be swapped between vehicles. If this message is received after having the vehicle serviced, check with your dealer/retailer. XM Radio ID: If tuned to channel 0, this message alternates with the XM Radio 8 digit radio ID label. This label is needed to activate the service. Unknown: If this message is received when tuned to channel 0, there could be a receiver fault. Consult with your dealer/retailer. Check XM Receivr: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer. XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer. Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. FM FM signals only reach about 16 to 65 km (10 to 40 miles). Although the radio has a built-in electronic circuit that automatically works to reduce interference, some static can occur, especially around tall buildings or hills, causing the sound to fade in and out. Infotainment System 6-13 AM The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. For better radio reception, most AM radio stations boost the power levels during the day, and then reduce these levels during the night. Static can also occur when things like storms and power lines interfere with radio reception. When this happens, try reducing the treble on the radio. XM™ Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out. In addition, traveling or standing under heavy foliage, bridges, garages, or tunnels may cause loss of the XM signal for a period of time. Cellular Phone Usage Cellular phone usage may cause interference with the vehicle’s radio. This interference may occur when making or receiving phone calls, charging the phone’s battery, or simply having the phone on. This interference can cause an increased level of static while listening to the radio. If static is received while listening to the radio, unplug the cellular phone and turn it off. Backglass Antenna The AM-FM antenna is integrated with the rear window defogger, located in the rear window. Make sure that the inside surface of the rear window is not scratched and that the lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception. For proper radio reception, the antenna connector needs to be properly attached to the post on the glass. 6-14 Infotainment System If a cellular telephone antenna needs to be attached to the glass, make sure that the grid lines for the AM-FM antenna are not damaged. There is enough space between the grid lines to attach a cellular telephone antenna without interfering with radio reception. Notice: Using a razor blade or sharp object to clear the inside rear window can damage the rear window antenna and/or the rear window defogger. Repairs would not be covered by the vehicle warranty. Do not clear the inside rear window with sharp objects. Notice: Do not apply aftermarket glass tinting with metallic ﬁlm. The metallic ﬁlm in some tinting materials will interfere with or distort the incoming radio reception. Any damage caused to your backglass antenna due to metallic tinting materials will not be covered by the vehicle warranty. Satellite Radio Antenna For vehicles with XM™ Satellite Radio Service, the antenna is located on the decklid of the vehicle. Keep the antenna clear of obstructions for clear radio reception. Audio Players CD Player The CD player can play audio CDs and MP3 CDs. The CD player will not play 8 cm (3 inches) CDs. Care of CDs Sound quality can be reduced due to disc quality, recording method, quality of the music recorded, and how the disc has been handled. Handle discs carefully and store them in their original cases or other protective cases away from direct sunlight and dust. If the bottom surface of a disc is damaged, the disc may not play properly or at all. Do not touch the bottom surface of a disc while handling it; this could damage the surface. Pick up discs by grasping the outer edges or the edge of the hole and the outer edge. If the bottom surface of a disc is dirty, take a soft lint free cloth, or dampen a clean soft cloth in a mild neutral detergent solution mixed with water, and clean it. Wipe the disc from the center to the outer edge. Care of the CD Player Do not add a label to a disc, as it could get caught in the CD player. If a label is needed, label the top of the recorded disc with a marking pen. Do not use disc lens cleaners because they could contaminate the lens of the disc optics and damage the CD player. Notice: or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs, the CD player could be damaged. While using the CD player, use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign materials, liquids, and debris. If a label is added to a CD, Control Buttons The buttons used to control the CD player are: CD/AUX: Press to choose between the CD and AUX player. g SEEK / l SEEK: Press to select tracks or to fast forward or rewind within a track. MENU/SELECT: Turn to select tracks. INFO: Press to display additional information about the CD that may be available. Z (Eject): Press to remove the CD. Inserting a CD With the printed side facing up, insert a disc into the CD slot until it is drawn in. Infotainment System 6-15 Removing a CD Press the Z button. The disc is pushed out of the CD slot. If the disc is not removed after it is ejected, it is pulled back in after a few seconds. Playing a CD or MP3 CD Press the CD/AUX button if there is a disc in the player, it begins playing. Information about the disc and current track is shown on the display depending on the data stored. Selecting a CD Track Using the control buttons: Press g SEEK or l SEEK to select the previous or next track. Turn the MENU/SELECT knob counterclockwise or clockwise to select the previous or next track. 6-16 Infotainment System Using the CD Menu: 1. Press the MENU/SELECT knob. 2. Select Tracks list. 3. Select the track. Playing Tracks in Random Order Press the MENU/SELECT knob and then set Shuffle Songs to On. Fast Forward and Rewind Press and hold l SEEK or g SEEK to fast forward or rewind within the current track. Selecting an MP3 Track Using the control buttons: Press g SEEK or l SEEK to select the previous or next track. Turn the MENU/SELECT knob counterclockwise or clockwise to select the previous or next track. Using the CD Menu: 1. Press the MENU/SELECT knob. 2. Select Playlists / Folders. 3. Select the play list or folder. 4. Select the track. Searching for MP3 Tracks It is normal for the search feature to take some time to display the information after reading the disc due to the amount of information stored on the disc. The infotainment system automatically switches to FM while the disc is being read. Tracks can be searched by: • Playlists • Artists • Albums • Song Titles • Genres • Folder View To search for tracks: 1. Press the MENU/SELECT knob. 2. Select Search. 3. Select: Playlists, Artists, Albums, Song Titles, Genres, or Folder View. 4. Select the track. Auxiliary Devices The AUX Input allows portable devices to connect to the vehicle using the 3.5mm (1/8 inch) input jack, the USB port, if equipped, or Bluetooth® wireless technology, if equipped. Portable devices are controlled by using the menu system described in Operation on page 6-4. Infotainment System 6-17 Searching For a Track Tracks can be searched for by: • Playlists • Artists • Albums • Song Titles • Podcasts • Genres • Audiobooks • Composers To search for tracks: 1. Press the MENU/SELECT knob. 2. Select Search. 3. Select: Playlists, Artists, Albums, Song Titles, Podcasts, Genres, Audiobooks, or Composers. 4. Select the track. Adjusting the Volume Turn the VOL O knob to adjust the volume of the Infotainment system after the volume level has been set on the portable audio device. iPod’s USB Port For vehicles with a USB port, the following devices may be connected and controlled by the infotainment system. • • PlaysForSure Devices (PFD) • USB Drives • Zune’s Connecting and Controlling an iPod™ Not all iPod’s can be controlled by the Infotainment System. Connecting an iPod Connect the iPod to the USB port using the cable that came with the device. The AUX input is located in the center console. 3.5mm Jack Connect a 3.5 mm (1/8 inch) cable to the auxiliary input jack to use a portable audio player. Playback of an audio device that is connected to the 3.5mm jack can only be controlled using the controls on the device. 6-18 Infotainment System Shuffle Press the MENU/SELECT knob and set Shuffle Songs (Random) to On or Off, then press the 0 BACK button to return the main screen. On: Plays tracks in the current folder in random order. Off: Plays tracks in the current folder in sequential order. Repeat Press the MENU/SELECT knob and set Repeat to On or Off, then press the 0 BACK button to return the main screen. On: Repeats the current track. Off: Playback starts from the beginning of the current track after the last track ﬁnishes. Connecting and Controlling a PlaysForSure Device (PFD) or Zune™ Connecting a PFD or Zune Connect the PFD or Zune to the USB port using the cable that came with the device. Searching For a Track Tracks can be searched for by: • Playlists • Artists • Albums • Song Titles • Podcasts • Genres To search for tracks: 1. Press the MENU/SELECT knob. 2. Select Search. 3. Select: Playlists, Artists, Albums, Song Titles, Podcasts, or Genres 4. Select the track. Shuffle Functionality Press the MENU/SELECT knob and set Shuffle Songs (Random) to On or Off. On: Plays current tracks in random order. Off: Plays current tracks in sequential order. Repeat Functionality Press the MENU/SELECT knob and set Repeat to On or Off. Repeat On: Repeats the current track. Repeat Off: Playback starts from the beginning of the current track after the last track ﬁnishes. Connecting and Controlling a USB Drive The infotainment system can only play back .mp3 and .wma ﬁles from a USB drive. Only the ﬁrst 10,000 songs are recognized on the device. When a device is not supported, the message “No supported data found. You can safely disconnect the device” appears. Connecting a USB Drive Connect the USB drive to the USB port using the cable that came with the device. Searching For a Track It is normal for the search feature to take some time to display the information after reading the disc due to the amount of information stored on the disc. Files that do not have any meta data stored in the ID3 tag display as Unknown. Tracks can be searched for by: • Playlists* • Artists • Albums • Song Titles • Genres • Folder View *This only displays if a playlist is found on the device. To search for tracks: 1. Press the MENU/SELECT knob. 2. Select Search. 3. Select: Playlists, Artists, Albums, Song Titles, Genres, or Folder View. 4. Select the track. Shuffle Functionality Press the MENU/SELECT knob and set Shuffle Songs (Random) to On or Off. On: Plays current tracks in random order. Infotainment System 6-19 Off: Plays current tracks in sequential order. Repeat Functionality Press the MENU/SELECT knob and set Repeat to On or Off. Repeat On: Repeats the current track. Repeat Off: Playback starts from the beginning of the current track after the last track ﬁnishes. Connecting a Bluetooth® Device Before a Bluetooth device can be connected to the infotainment system, it must ﬁrst be paired to the system. Not all Bluetooth devices can be paired to the infotainment system. Before pairing the Bluetooth device, become familiar with its user guide for Bluetooth functions. The system only connects to Bluetooth devices that support A2DP (Advanced Audio Distribution Proﬁle) version 1.2. 6-20 Infotainment System Pairing Information: • Up to ﬁve devices can be paired to the system. • The pairing process is disabled when the vehicle is moving. • The infotainment system automatically links with the ﬁrst available paired device in the order the device was paired. • Only one paired device can be connected to the infotainment system at a time. • Pairing should only need to be completed once, unless changes to the pairing information have been made or the device is deleted. Bluetooth Setup Menu The Bluetooth Setup menu can be accessed with or without a device attached to the USB port. To select the Bluetooth Setup menu when a device is attached to the USB port and active: 1. Press the MENU/SELECT knob while in the iPod, Zune, PFD, or USB device main menu. 2. Select Bluetooth Music Setup. To select the Bluetooth Music Setup menu when a device is not attached to the USB port, or when a device is attached to the USB port but not active: 1. Press the CD/AUX button until AUX is the active source. 2. Press the MENU/SELECT knob. 3. Select Bluetooth Music Setup. To select the Bluetooth Music Setup menu when a Bluetooth device is connected and active: 1. Press the MENU/SELECT knob. 2. Select Bluetooth Music Setup. Pairing a Device 1. Select Connect To New Device from the Bluetooth Music Setup menu. 2. The system asks a series of Yes/No questions to determine what type of device is being paired. 3. After the system determines what type of Bluetooth device is being paired, the Bluetooth device will need to be put into discovery mode. 4. Some devices may require a PIN number in order to complete the pairing process. Locate the device named “GMusicConnect” in the list on the Bluetooth device and follow the instructions on the device to enter the four digit PIN number provided by the Infotainment System. Connecting to a Device Once a device is paired to the Infotainment System, it can be connected to the Infotainment System. To connect a paired device when no other device is connected to the Infotainment System: 1. Select the Select Device option from the Bluetooth Music Setup menu. 2. Select the new device. To connect a paired device when another device is connected to the Infotainment System: 1. Select the Select Device option from the Bluetooth Music Setup menu. 2. Select the new device. 3. The active device is disconnected from the system and the new device is connected. Removing a Device 1. Select Remove Device from the Bluetooth Music Setup menu. 2. Select the device. 3. The device is removed from the system. Before connecting to the removed device again, it will need to paired to the Infotainment System. Infotainment System 6-21 Changing the Default PIN To change the default PIN: 1. Select Change Default PIN from the Bluetooth Music Setup menu. 2. Select one of the pre-deﬁned PIN numbers, or select Other to create a PIN. To create a PIN: 1. Select the length of the PIN number. 2. Enter the character sequence. Messages The following messages may appear on the infotainment screen. Poor Bluetooth Signal Quality: This message displays when the Bluetooth signal strength is low. This Feature is Unavailable While Vehicle is Moving: This message displays when an action is not allowed while the vehicle is moving. 6-22 Infotainment System Controlling a Bluetooth® Device Bluetooth devices that support AVRCP (Audio/Video Remote Control Proﬁle) version 1.0 may be able to be controlled by the Infotainment System. Press and release g SEEK / l SEEK to skip tracks. Press and hold g SEEK / l SEEK to fast forward or fast reverse within a track. Other Information The Bluetooth® word mark and logos are owned by the Bluetooth® SIG, Inc. and any use of such marks by General Motors is under license. Other trademarks and trade names are those of their respective owners. See Radio Frequency Statement (US, Can) on page 12-15 for FCC information. Phone Bluetooth (Overview) Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Proﬁle to make and receive phone calls. The infotainment system and voice recognition are used to control the system. The system can be used while in ON/RUN or ACC/ACCESSORY. The range of the Bluetooth system can be up to 9.1 m (30 ft.). Not all phones support all functions and not all phones work with the Bluetooth system. See www.gm.com/bluetooth for more information about compatible phones. Bluetooth Controls Use the buttons located on the infotainment system and the steering wheel to operate the Bluetooth system. Steering Wheel Controls b / g (Push To Talk): Press to answer incoming calls, to conﬁrm system information, and to start voice recognition. c / $ (End Call / Mute): Press to end a call, reject a call, or to cancel an operation. Infotainment System Controls MENU/SELECT: Press and turn to navigate the menu screens. See Operation on page 6-4 for more information. PHONE: Press to enter the Phone main menu. CONFIG: Press to enter the System Conﬁguration menu. Voice Recognition The voice recognition system is used to interpret commands that control the system and dial phone numbers. Noise: The system may not recognize voice commands if there is too much background noise. When to Speak: A tone sounds to indicate that the system is ready for a voice command. Wait for the tone and then speak. How to Speak: Speak clearly in a calm and natural voice. Audio System When using the Bluetooth system, sound comes through the vehicle’s front audio system speakers and overrides the audio system. Use the audio system volume knob, during a call, to change the volume level. The adjusted volume level remains in memory for later calls. The system maintains a minimum volume level. Other Information The Bluetooth® word mark and logos are owned by the Bluetooth® SIG, Inc. and any use of such marks by General Motors is under license. Other trademarks and trade names are those of their respective owners. See Radio Frequency Statement (US, Can) on page 12-15 for FCC information. Bluetooth (Infotainment Controls) Pairing A Bluetooth enabled cell phone must be paired to the Bluetooth system ﬁrst and then connected to the vehicle before it can be used. See the cell phone manufacturer user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected, calls will be made using OnStar® Hands-Free Infotainment System 6-23 Calling, if available. Refer to the OnStar owner’s guide for more information. The pairing process can be started by using the voice recognition system or the controls on the infotainment system. Pairing Information: • Up to ﬁve cell phones can be paired to the Bluetooth system. • The pairing process is disabled when the vehicle is moving. • The Bluetooth system automatically links with the ﬁrst available paired cell phone in the order the phone was paired. • Only one paired cell phone can be connected to the Bluetooth system at a time. • Pairing should only need to be completed once, unless changes to the pairing information have been made or the phone is deleted. 6-24 Infotainment System To link to a different paired phone, see Linking to a Different Phone later in this section. Pairing a Phone 1. Press the CONFIG button. 2. Select Phone Settings. 3. Select Bluetooth 4. Select Pair Device (Phone) 5. Start the Pairing process on the cell phone that will be paired to the vehicle. Reference the cell phone manufacturer user guide for information on this process. Locate the device named “General Motors” in the list on the cell phone and follow the instructions on the cell phone to enter the four digit PIN number that appears on the infotainment display. 6. The system prompts for a name for the phone. Use a name that best describes the phone. This name will be used to indicate which phone is connected. The system then conﬁrms the name provided. 7. The system responds “ has been successfully paired” after the pairing process is complete. 8. Repeat Steps 1 through 7 for additional phones to be paired. Listing All Paired and Connected Phones 1. Press the CONFIG button. 2. Select Phone Settings. 3. Select the Bluetooth submenu. 4. Select Device List submenu. Deleting a Paired Phone 1. Press the CONFIG button. 2. Select Phone Settings. 3. Select the Bluetooth submenu. 4. Select Device List submenu. 5. Select the phone to be deleted and then follow the on screen prompts. Linking to a Different Phone 1. Press the CONFIG button. 2. Select Phone Settings. 3. Select the Bluetooth submenu. 4. Select Device List submenu. 5. Select the new phone and then follow the on screen prompts. Making a Call 1. Press the PHONE button twice. 2. Select Enter number. 3. Enter the character sequence. See “Entering a Character Sequence” in the Operation on page 6-4 for more information. 4. Select Call to start dialing the number. Accepting or Declining an Incoming Call When an incoming call is received, the infotainment system mutes and a ring tone is heard in the vehicle. Accepting a Call Turn the MENU/SELECT knob to “Answer” and press the MENU/SELECT knob to accept the incoming call. Declining a Call Turn the MENU/SELECT knob to “Decline” and press the MENU/SELECT knob to decline the incoming call. Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. Accepting a Call Turn the MENU/SELECT knob to “Answer” and press the MENU/SELECT knob to accept the incoming call. Declining a Call Turn the MENU/SELECT knob to “Decline” and press the MENU/SELECT knob to decline the incoming call. Switching Between Calls To switch between calls: 1. Press the MENU/SELECT knob. 2. Select Switch Call from the menu. Conference Calling Conference calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. Infotainment System 6-25 To start a conference while in a current call: 1. Press the MENU/SELECT knob and select Enter Number. 2. Enter the character sequence then select call. See “Entering a Character Sequence” in the Operation on page 6-4 for more information. 3. After the call has been placed, press the MENU/SELECT knob and choose Merge Calls. 4. To add more callers to the conference call, repeat steps 1 through 3. The number of callers that can be added are limited by your wireless service carrier. Ending a Call Press the MENU/SELECT knob and select Hang Up. 6-26 Infotainment System Muting a Call To Mute a Call Press the MENU/SELECT knob and select Mute Call. To Cancel Mute Press the MENU/SELECT knob and deselect Mute Call. Dual Tone Multi-Frequency (DTMF) Tones The in-vehicle Bluetooth system can send numbers during a call. This is used when calling a menu driven phone system. 1. Press the MENU/SELECT knob and select Enter Number. 2. Enter the character sequence. See “Entering a Character Sequence” in the Operation on page 6-4 for more information. Bluetooth (Voice Recognition) Pairing A Bluetooth cell phone must be paired to the Bluetooth system and then connected to the vehicle before it can be used. See the cell phone manufacturer user guide for Bluetooth functions before pairing the cell phone. If a Bluetooth phone is not connected, calls will be made using OnStar® Hands-Free Calling, if available. Refer to the OnStar owner’s guide for more information. The pairing process can be started by using the voice recognition system or the controls on the infotainment system. Pairing Information: • Up to ﬁve cell phones can be paired to the Bluetooth system. • The pairing process is disabled when the vehicle is moving. • The Bluetooth system links with the ﬁrst available paired cell phone in the order the phone was paired. • Only one paired cell phone can be connected to the Bluetooth system at a time. • Pairing should only need to be completed once, unless changes to the pairing information have been made or the phone is deleted. To link to a different paired phone, see Linking to a Different Phone later in this section. Pairing a Phone 1. Press b g. The system responds “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds “Bluetooth ready” followed by a tone. 3. Say “Pair”. The system responds with instructions and a four-digit PIN number. The PIN number will be used in Step 4. 4. Start the Pairing process on the cell phone that will be paired to the vehicle. Reference the cell phone manufacturer user guide for information on this process. Locate the device named “General Motors” in the list on the cell phone and follow the instructions on the cell phone to enter the four-digit PIN number that was provided in Step 3. 5. The system prompts for a name for the phone. This name will be used to indicate which phone is connected. The system conﬁrms the name. 6. The system responds “ has been successfully paired” after the pairing process is complete. 7. Repeat Steps 1 through 7 for additional phones to be paired. Listing All Paired and Connected Phones 1. Press bg. The system responds “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds “Bluetooth ready” followed by a tone. 3. Say “List”. The system lists all the paired Bluetooth devices. The system will respond “is connected” if a phone is connected to the vehicle. Infotainment System 6-27 Deleting a Paired Phone 1. Press bg. The system responds “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds “Bluetooth ready” followed by a tone. 3. Say “Delete”. The system asks which phone to delete followed by a tone. 4. Say the name of the phone to be deleted. If the phone name is unknown, use the “List” command for a list of all paired phones. The system responds “Would you like to delete ? Yes or No” followed by a tone. 5. Say “Yes” to delete the phone. The system responds “OK, deleting ”. 6-28 Infotainment System Linking to a Different Phone 1. Press bg. The system responds “Ready” followed by a tone. 2. Say “Bluetooth”. The system responds “Bluetooth ready” followed by a tone. 3. Say “Change phone”. The system responds “Please wait while I search for other phones”. • If another phone is found, the response will be “ is now connected”. If another phone is not found, the original phone remains connected. • Storing Name Tags The system can store up to thirty phone numbers as name tags that are shared between the Bluetooth and OnStar systems. The system uses the following commands to store and retrieve phone numbers: • Store • Digit Store • Directory Using the Store Command The store command allows a phone number to be stored without entering the digits individually. 1. Press bg. The system responds “Ready” followed by a tone. 2. Say “Store”. The system responds “Store, number please” followed by a tone. 3. Say the complete phone number • to be stored at once with no pauses. • If the system recognizes the number the response is “OK, Storing”. If the system does not recognizes the phone number, the response is “Store ”. “Please say yes or no”. If the number is correct, say “Yes”. If the number is not correct, say “No”. The system will ask for the number again. 4. After the system stores the phone number, it responds “Please say the name tag” followed by a tone. 5. Say a name tag for the phone number. The name tag is recorded and the system responds “About to store . Does that sound OK?”. • If the name tag does not sound correct, say “No” and repeat Step 5. If the name tag sounds correct, say “Yes” and the name tag is stored. After the number is stored the system returns to the main menu. • Infotainment System 6-29 2. Say “Digit Store”. The system responds “Please say the ﬁrst digit to store” followed by a tone. 3. Say the ﬁrst digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. • If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number. 5. Say a name tag for the phone number. The name tag is recorded and the system responds “About to store . Does that sound OK?”. • If the name tag does not sound correct, say “No” and repeat Step 5. If the name tag sounds correct, say “Yes” and the name tag is stored. After the number is stored the system returns to the main menu. • Using the Digit Store Command The digit store command allows a phone number to be stored by entering the digits individually. 1. Press b g. The system responds “Ready” followed by a tone. • To hear all of the numbers recognized by the system, say “Verify” at any time. 4. After the complete number has been entered, say “Store”. The system responds “Please say the name tag” followed by a tone. Using the Directory Command The directory command lists all of the name tags stored by the system. To use the directory command: 1. Press bg. The system responds “Ready” followed by a tone. 2. Say “Directory”. The system responds “Directory” and lists all stored name tags. The system returns to the main menu when the list is complete. 6-30 Infotainment System Deleting Name Tags The system uses the following commands to delete name tags: • Delete • Delete all name tags Using the Delete Command The delete command is used to delete speciﬁc name tags. To delete name tags: 1. Say “Delete”. The system responds “Delete, please say the name tag” followed by a tone. 2. Say the name tag to be deleted. The system responds “Would you like to delete, ? Please say yes or no”. • If the name tag is correct, say “Yes” to delete the name tag. The system responds “OK, deleting , returning to the main menu.” • If the name tag is incorrect, say “No”. The system responds “No. OK, let’s try again, please say the name tag.” Using the Delete All Name Tags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar if stored. To delete all name tags: 1. Press b g. The system responds “Ready” followed by a tone. 2. Say “Delete all name tags”. The system responds “You are about to delete all name tags stored in your phone directory and your route destination directory. Are you sure you want to do this? Please say yes or no.” • Say “Yes” to delete all name tags. • Say “No” to cancel the function and return to the main menu. Making a Call Calls can be made using the following commands: • Dial • Digit Dial • Call • Re-dial Using the Dial Command 1. Press b g. The system responds “Ready” followed by a tone. 2. Say “Dial”. The system responds “Dial using . “Number please” followed by a tone. 3. Say the entire number without pausing. • • If the system recognizes the number, it responds “OK, Dialing” and dials the number. If the system does not recognize the number, it conﬁrms the numbers followed by a tone. If the number is correct, say “Yes”. The system responds “OK, Dialing” and dials the number. If the number is not correct, say “No”. The system will ask for the number again. Using the Digit Dial Command 1. Press b g. The system responds “Ready” followed by a tone. 2. Say “Digit Dial”. The system responds “Digit dial using , please say the ﬁrst digit to dial” followed by a tone. 3. Say the digits to be dialed one at a time. The system repeats back the digit it heard followed by a tone. 4. Continue entering digits until the number to be dialed is complete. After the whole number has been entered, say “Dial”. The system responds “OK, Dialing” and dials the number. • If an unwanted number is recognized by the system, say “Clear” at any time to clear the last number. • To hear all of the numbers recognized by the system, say “Verify” at any time. Infotainment System 6-31 Using the Call Command 1. Press b g. The system responds “Ready” followed by a tone. 2. Say “Call”. The system responds “Call using . Please say the name tag” followed by a tone. 3. Say the name tag of the person to call. • • If the system recognizes the name tag it responds “OK, calling, ” and dials the number. If the system does not

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2010 Chevrolet Camaro Owners Manual