2009 Acura MDX Owners Manual

CONTINUED 119

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Fog Lights Turn the fog lights on and off by turning the switch next to the headlight switch. You can use the fog lights only when the headlights are on low beam. With the light switch in the AUTO position, you can also use the fog lights when the headlights turn on automatically. They will go off when the headlights turn off.

Daytime Running Lights With the headlight switch off, the daytime running lights come on when you turn the ignition switch to the ON (II) position and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake. When the headlights are on, the daytime running lights are off.

Turn Signal and Headlights

LIGHT SENSOR

The automatic lighting feature is controlled by a sensor located on top of the dashboard. Do not cover this sensor or spill liquids on it.

120

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

If you see a ‘‘CHECK DRL SYSTEM’’ message on the multi-information display, there is a problem with the daytime running light system. Take your vehicle to a dealer to have it checked. When the multi-information display shows a ‘‘DRL OFF’’ message, the daytime running lights are off. Follow the procedure in the left column to turn them on.

Automatic Lighting Off Feature This feature turns off the headlights, all other exterior lights, and the instrument panel lights within 15
seconds after you remove the key and close the driver's door. To change the ‘‘HEADLIGHT AUTO OFF TIMER’’ setting, see page 102. The automatic lighting off feature activates if you leave the headlight switch in the ‘‘ position or if the lights are turned on by setting the switch in the ‘‘AUTO’’ position, and you remove the key, then open and close the driver's door.

’’ or ‘‘

’’

Turn Signal and Headlights

If you turn the ignition switch to the LOCK (0) position with the headlight switch on, but do not open the door and get out, the lights turn off after 10 minutes (3 minutes, if the switch is in the ‘‘AUTO’’ position). The lights turn on again when you unlock or open the driver's door. If you unlock the door, but do not open it within 15 seconds, the lights go off. With the driver's door open, you will hear a lights-on reminder chime.

121

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Hazard Warning Button, Rear Window Defogger

Hazard Warning Button

Rear Window Defogger

Push the button between the center vents to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.

The rear window defogger will clear fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button lights to show the defogger is on. If you do not turn it off, the defogger will shut itself off after about 15 minutes. It also shuts off when you turn off the ignition. You have to turn it on again when you restart the vehicle.

122

Make sure the rear window is clear and you have good visibility before starting to drive. The defogger wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side-to-side. Pushing this button also turns the mirror heaters on or off. For more information, see page 156.

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Adjust the brightness of the instrument panel by pressing the ＋ or － button. Press the ＋ button to increase the brightness and the － button to decrease it. The brightness can be set differently for when the headlights are on, and when they are off.

The level of brightness is shown on the multi-information display while you adjust it. It goes out 5 seconds after you finish adjusting.

Instrument Panel Brightness

. To cancel the glare reduction

To reduce glare at night, the instrument panel illumination dims when you turn the light switch to or function, set the brightness to the highest level, then press the ＋ button. You will hear a beep when it is canceled. You can customize when the glare reduction function starts. To change ‘‘AUTO INTERIOR ILLUMINATION’’, see page 95 for more information.

123

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Steering Wheel Adjustments

Make any steering wheel adjustment before you start driving.

ADJUSTMENT SWITCH

Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.

Adjust the steering wheel only when the vehicle is stopped.

Move the steering wheel in, out, up, or down by pushing and holding the adjustment switch in that direction.

Release the switch when the steering wheel reaches the desired position. Make sure the steering wheel points towards your chest, not toward your face, and that you can see the instrument panel gauges and indicators.

124

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

When you remove the key from the ignition switch, the steering wheel automatically moves fully in and up. To change the ‘‘AUTO TILT & TELESCOPE STEERING WHEEL’’ setting, see page 99. The steering wheel then returns to its original position when you insert the key back in the ignition switch. Steering wheel movement is also controlled by the driving position memory system (see page 157).

If your vehicle's battery is disconnected or goes dead, or the fuse for the power tilt and telescopic steering wheel is removed, the power tilt and telescopic steering wheel system needs to be reset when you reconnect the battery or install the fuse. Insert the key into the ignition switch, and remove it. The steering wheel automatically moves fully in and up to let you know the system is reset.

Steering Wheel Adjustments

125

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Keys and Locks

KEY NUMBER TAG

MASTER KEY WITH REMOTE TRANSMITTER

VALET KEY (Light Gray)

KEY NUMBER TAG

MASTER KEY WITH REMOTE TRANSMITTER

VALET KEY (Light Gray)

Models without power tailgate The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver's door lock. You can keep the glove box locked when you leave your vehicle and the valet key at a parking facility.

Models with power tailgate You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Acura-approved key blanks.

These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged. ● Protect the keys from direct

sunlight, high temperature, and high humidity.

● Do not drop the keys or set heavy

objects on them.

● Keep the keys away from liquids.

If they get wet, dry them immediately with a soft cloth. The valet key does not contain a battery. Do not try to take it apart.

126

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

RetractableMasterKey

RELEASE BUTTON

Push

Always use the fully-extended key when you insert it to the ignition switch. If the key does not fully extend, the immobilizer system may not operate properly and prevents from starting the engine.

The key may come in contact with your finger while being retracted or extended. Make sure your fingers do not touch the pivot of the key when retracting or extending the key.

Keys and Locks

Models with power tailgate shown The master key can be retracted into the remote transmitter. To use the key, push the release button to release the key from the transmitter. The key should be fully extended. To retract the key, push the release button and at the same time push the key into the remote transmitter until it is securely latched.

127

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

If the system repeatedly does not recognize the coding of your key, contact your dealer. Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle inoperable. If you have lost your key and you cannot start the engine, contact your dealer.

Always take the ignition key with you whenever you leave the vehicle alone.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation. Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser's authoritytooperatetheequipment. ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

Immobilizer System

The Immobilizer System protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine's fuel system is disabled. When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again. The system may not recognize your key's coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.

128

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

ACCESSORY (I) － You can operate the audio system and the accessory power sockets in this position. ON (II) － This is the normal key position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position. START (III) － Use this position only to start the engine. The switch returns to the ON (II) position when you let go of the key.

Ignition Switch

You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver's door. Remove the key to turn off the beeper. The shift lever must be in Park before you can remove the key from the ignition switch.

129

The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III). LOCK (0) － You can insert or remove the key only in this position. To turn the key to the LOCK (0) position, the shift lever must be in Park, and you must push the key in slightly. If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Door Locks

UNLOCK

LOCK

LOCK

UNLOCK

To lock all doors and the tailgate, press the bottom of the master door lock switch on either front door, pull the lock tab above the driver's door handle, or use the key on the outside lock on the driver's door. Pressing the top of either master door lock switch will unlock all doors and the tailgate.

The lock tab on any passenger's door locks and unlocks that door. All doors and the tailgate can be locked from the outside by using the key in the driver's door lock. To unlock only the driver's door, insert the key, turn the key, and release it. The remaining doors and the tailgate unlock when you turn the key a second time within a few seconds.

130

To change the ‘‘KEY AND REMOTE UNLOCK MODE’’ setting, see page 109. When the vehicle speed reaches about 10 mph (about 16 km/h) or more, all the doors lock automatically. To change the ‘‘AUTO DOOR LOCK’’ setting, see page 106. When you shift to P after driving, the driver's door unlocks. To change the ‘‘AUTO DOOR UNLOCK’’ setting, see page 107.

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

LockoutPrevention With any door and the tailgate open and the key in the ignition, both master door lock switches are disabled. They are not disabled if all the doors and the tailgate are closed. If you try to lock an open driver's door by pulling the lock tab rearward the lock tab on the driver's door pops out.

Door Locks, Tailgate

Childproof Door Locks

Tailgate

LOCK

The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position (lever is down), the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, push the lock tab forward and use the outside door handle.

To open the tailgate, push up inside the handle, then lift up. To close the tailgate, use the inner handle to pull it down, then press down on the back edge. Keep the tailgate closed at all times while driving to avoid damaging the tailgate and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 58.

131

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Tailgate

Power Tailgate

If you push the same button or switch again while the tailgate is opening or closing, you will hear three beeps, and the tailgate will stop moving, reverse direction, and stop at the fully opened or closed position.

POWER TAILGATE SWITCH

Ifequipped The tailgate can be opened and closed with the remote transmitter (see page 135) or the switch in the driver's door pocket when both front doors are unlocked. Press and hold the tailgate button on the remote transmitter or the switch for about 1 second to open or close the tailgate. Each time you press the button on the remote transmitter or the switch, you will hear a beep, and some front and rear lights will flash.

132

TAILGATE SWITCH

The tailgate can also be closed by pressing the button on the tailgate. If you press the button again while the tailgate is closing, you will hear three beeps, and the tailgate will stop moving, reverse direction, and stop at the fully opened position.

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Auto-Reverse The power tailgate has an auto- reverse feature. If it meets resistance while opening or closing, it will beep three times and reverse direction. However, the tailgate may not reverse immediately. Always make sure passengers and objects are clear of the tailgate before opening or closing it.

Closing a power tailgate while anyone is in the path of the tailgate can cause serious injury.

Make sure everyone is clear before closing the power tailgate.

Also check that passengers, especially children, do not have their hands on the edge of the tailgate or on the tailgate sill. The auto reverse feature stops working when the tailgate is about to latch so the motor can pull the tailgate shut. If your vehicle's battery is disconnected, goes dead, or the fuse is removed while the tailgate is fully open, the power tailgate needs to be reset. After connecting the battery or installing the fuse, close the tailgate fully by hand. The power tailgate may not open or close under the these conditions: ● The vehicle is parked on a steep

hill.

● When the vehicle is swayed in a

strong wind.

Tailgate

● When the tailgate or the roof is

covered with snow or ice.

Do not install any accessories on the tailgate. It may cause the tailgate not to function properly. If there is snow or ice on the tailgate, make sure to remove it before you operate the tailgate. If you push the tailgate release button inside the handle while the tailgate is opening or closing, it will stop moving. You need to open or close it the rest of the way manually. The tailgate has sensors on both sides. Be careful not to damage them. If the sensors are damaged, the power tailgate does not function properly.

CONTINUED 133

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Tailgate

If you try to drive off with the tailgate not closed completely, a beeper sounds and a ‘‘DOOR & TAILGATE OPEN’’ message is shown on the multi-information display. Keep the tailgate closed at all times while driving to avoid damaging the tailgate and to prevent exhaust gas from getting into the interior. See Carbon Monoxide Hazard on page 58. If there is a problem in the power tailgate system, you will see a ‘‘CHECK POWER TAILGATE’’ message on the multi-information display. Have the system checked by your dealer. With this message shown on the multi-information display, you can still open or close the tailgate manually.

134

Unlocking the Tailgate

Modelswithpowertailgate If the power door lock system cannot unlock the tailgate, unlock it manually. Use a small flat-tipped screwdriver to remove the cover on the back of the tailgate.

Push the release lever to the right as shown. If you need to unlock the tailgate manually, it means there is a problem with the tailgate. Have the vehicle checked by your dealer.

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Modelswithoutpowertailgate If you cannot open the tailgate, remove the cover on the back of the tailgate (see page 134). Push the release lever to the right as shown, then pull the outer handle to open the tailgate.

Tailgate, Remote Transmitter

Models with power tailgate

UNLOCK BUTTON

LOCK BUTTON

TAILGATE BUTTON

PANIC BUTTON To change the ‘‘KEYLESS LOCK ACKNOWLEDGEMENT’’ setting, see page 110.

Remote Transmitter

Models without power tailgate

UNLOCK BUTTON

LOCK BUTTON

PANIC BUTTON

LOCK － Press this button once to lock all doors and the tailgate. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors and tailgate are locked and the security system has set. This button does not work if any door or tailgate is not fully closed.

CONTINUED 135

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

When you press the UNLOCK button, the front and rear individual map lights and the cargo area light, depending on their switch positions, will come on (see page 160). If you do not open any door or the tailgate, the lights stay on for about 30
seconds, then go out. If you relock the doors and the tailgate with the remote transmitter before 30 seconds have elapsed, the lights will go off immediately. Modelswithpowertailgate TAILGATE － Press and hold the TAILGATE button to open or close the power tailgate. When the tailgate begins to move, you will hear a beep, and some front and rear lights will flash.

If you push the same button again while the tailgate is opening or closing, three beeps sound, the tailgate stops moving, reverses direction and stops in the fully opened or fully closed position. PANIC － Press and hold this button for about 1 second to attract attention; the horn will sound, and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to the ON (II) position. Panic mode does not work when the key is in the ignition switch.

Remote Transmitter

UNLOCK － Press this button once to unlock the driver's door. Push it twice to unlock the other doors. Some exterior lights will flash twice when you push the button. If you do not open any door or the tailgate within 30 seconds, they will automatically relock. To change the ‘‘KEY AND REMOTE UNLOCK MODE’’ setting, see page 109. To change the ‘‘SECURITY RELOCK TIMER’’ setting, see page 111.

136

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

RemoteTransmitterCare ● Avoid dropping or throwing the

transmitter.

● Protect the transmitter from

extreme temperature.

● Do not immerse the transmitter in

any liquid.

● If you lose a transmitter, the

replacement needs to be reprogrammed by your dealer.

Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors and the tailgate, replace the battery as soon as possible. Battery type: CR1616

Remote Transmitter

SCREW

KEYPAD

To replace the battery: 1. Remove the screw at the base of

the transmitter with a small Phillips-head screwdriver.

2. Separate the keypad from the

transmitter by pushing any button from outside.

CONTINUED 137

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

4. Remove the old battery and note

the polarity. Make sure the polarity of the new battery is the same (－ side facing up), then insert it in the keypad. An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.

5. Snap the two halves of the keypad,

then install the parts in reverse order.

AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation. Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser's authoritytooperatetheequipment. ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.

Remote Transmitter

BATTERY

3. Place a cloth on the edge of the

keypad, and remove the upper half by carefully prying on the edge with a small flat-tip screwdriver.

138

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Keyless Memory Settings™

When you unlock the driver's door with your remote, each remote activates the keyless memory settings related to that remote. The driver's ID (MEMORY 1 or MEMORY 2) is shown on the back of each remote.

Here are the settings activated with the remote: ● Customized settings

(see page 83).

● Driving position memory

(see page 157).

● Audio system settings

(see page 200).

● Climate control settings

(see page 171).

When you unlock and open the driver's door with the remote transmitter, the driver's seat (except the power lumbar feature) and outside mirrors start to move to the positions stored in memory. The indicator in the related memory button to the remote comes on.

Remote Transmitter

The steering wheel will move to the stored position when you insert the key into the ignition switch. You will also see the ‘‘WELCOME DRIVER 1’’ or ‘‘WELCOME DRIVER 2’’ message on the multi-information display, depending on which linked remote transmitter is used. To turn off this feature, press and hold the LOCK and UNLOCK buttons at the same time. The LED in the remote will blink twice. Then release the buttons. Doing this cancels the keyless memory settings for that remote and restores the default settings. To turn the keyless memory settings back on, repeat this procedure. The LED will blink once to indicate the feature has been turned on.

139

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Seats

Front Seat Power Adjustments Seepages12－14forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs. The controls for the power adjustable front seats are on the outside edge of each seat bottom. You can adjust the seats with the ignition switch in any position. Make all seat adjustments before you start driving. The passenger seat has the same adjustments as the driver's seat but without any lumbar adjustment.

140

Moves the seat forward and backward.

Moves the front of the seat up or down.

Raises or lowers the seat.

Moves the whole seat up and forward, or down and backward. The front of the seat also tilts up or down at the same time.

Adjusts the seat-back angle forward or backward.

Increases or decreases the lumbar support. (Driver's seat only)

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Head Restraints Seepage14forimportantsafety informationandawarningabout improperlypositioningheadrestraints. Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from whiplash and other injuries.

They are most effective when you adjust them so the center of the back of the occupant's head rests against the center of the restraint.

Seats

CUSHION

FRONT

SEAT- BACK

LEGS

RELEASE BUTTON

AdjustingtheHeadRestraint The head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways, and push the restraint down.

CONTINUED 141

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

When reinstalling a head restraint, put the legs back in place. Then adjust it to the appropriate height while pressing the release button. Make sure the head restraint locks in position when you reinstall it.

Failure to reinstall the head restraints can result in severe injury during a crash.

Always replace the head restraints before driving.

Seats

SECOND CENTER AND THIRD ROW CUSHION

LEGS

RELEASE BUTTON

RemovingtheHeadRestraint To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button, then pull the restraint out of the seat- back.

142

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

ActiveHeadRestraints

After a collision, the activated restraint should return to its normal position. If the restraints do not return to their normal position, or in the event of a severe collision, have the vehicle inspected by an Acura dealer.

The driver's and front passenger's seats have active head restraints. If the vehicle is struck severely from the rear, the occupant properly secured with the seat belt will be pushed against the seat-back and the head restraint will automatically move forward. This reduces the distance between the restraint and the occupant's head. It also helps protect the occupants against whiplash and injuries to the neck and upper spine.

Seats

For a head restraint system to work properly: ● Do not hang any items on the head

restraints, or from the restraint legs.

● Do not place any object between

an occupant and the seat-back.

● Install each restraint in its proper

location.

● Only use genuine Acura

replacement head restraints.

CONTINUED 143

2009 MDX Make sure that the folded seat-back does not press against the front passenger's seat, as this could cause the weight sensors to work improperly.

08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Seats

Adjusting the Second Row Seats

HANDLE

To change the seat-back angle of the seats in the second row, pull up on the handle on the outside of the seat- back, and push the seat-back. Overall, the seat-back has six different positions.

144

Folding the Second Row Seats The left and right halves can be folded separately. 1. To unlatch the detachable anchor before folding the seat-back, insert the latch plate into the slot on the side of the anchor buckle (see page 146) and allow the seat belt to retract. Store the detachable anchor and seat belt latch plates in the retractor housing.

2. Lower the head restraints to their

lowest positions.

3. Pull up the handle on the outside

of the seat-back.

4. Fold the seat-back forward. Reverse this procedure to return the seat to the upright position. Make sure the seat is locked securely before driving.

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Third Row Access

Folding the Third Row Seat 1. Use the latch plate to release the

seat belt from the detachable anchor (see page 146).

2. Lower the head restraints to their

lowest positions.

NOTE: To fold the third row seat, the second row seat-back must be folded down or in the full up right position.

RELEASE LEVER To get into the third row seats, pull up the lever on the side of the passenger's side second row seat- back. The seat-back will tilt forward, and then can be slid forward. After you return the seat-back to the upright position, push the whole seat backwards until it latches. Make sure the seat is fully latched before sitting in it.

Seats

THIRD SEAT

HANDLE 3. Unlock the seat-back by pulling the handle. Push the seat-back forward.

Make sure the outer shoulder belts are positioned on each hook on the side panel whenever the third seat is folded.

CONTINUED 145

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Seats

Reverse this procedure to return the seat to the upright position. Make sure the seat is locked securely before driving. Reconnect the seat belts to the detachable anchors. Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have to brake hard (See Carrying Cargo on page 332).

Detachable Anchor

LATCH PLATE

The seat belts in the second row center seat and the third row seats are equipped with detachable anchors. To unlatch the detachable anchor, insert the latch plate into the slot on the side of the anchor buckle. Store the detachable anchor and seat belt latch plates in the retractor housing.

146

When the seats are returned to the upright position, these detachable anchors should be latched back properly.

Using the seat belt with the detachable anchor unlatched increases the chance of serious injury or death in a crash.

Before using the seat belt, make sure the detachable anchor is correctly latched.

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

SECOND ROW CENTER SEAT

THIRD ROW SEATS

SMALL LATCH PLATE

LATCH PLATE

Seats

SMALL LATCH PLATE

HOOK

Pull out the small latch plate and the latch plate from each holding slot in the ceiling, and pull out the seat belt to extend it.

Pull out the outer shoulder belts from the hook. Both of the third-row hooks should only be used when the seat belt is detached.

TRIANGLE MARKS

ANCHOR BUCKLE

Line up the triangle marks on the small latch plate and anchor buckle when reattaching the belt and buckle. Tug on the seat belt to verify that the detachable anchor is securely latched. Make sure the seat belt is not twisted.

147

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Seat Heaters

Passenger's Seat

HI

HEATERS

Driver's Seat

Front seat

LOW

Both front seats are equipped with seat heaters. Because of the sensors for the side airbag cutoff system, there is no heater in the passenger's seat-back. The ignition switch must be in the ON (II) position to use the heaters.

Push the front of the switch, HI, to rapidly heat up the seat. After the seat reaches a comfortable temperature, select LO by pushing the back of the switch. This will keep the seat warm.

Second row seat

U.S.EntertainmentPackagesand Canadianmodels The outer second row seat cushions and seat-backs are equipped with seat heaters. Turning the switch on the driver side warms the outer seat behind the driver's seat only. The passenger side switch warms the outer seat behind the front passenger seat.

148

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

In the HI setting, the heater turns off when the seat gets warm, and turns back on after the seat's temperature drops. In the LO setting, the heater runs continuously. It does not cycle with temperature changes. Follow these precautions when using the seat heaters: ● Use the HI setting only to heat the

seats quickly, because it draws large amounts of current from the battery.

● If the engine is left idling for an extended period, do not use the seat heaters even on the LO setting. It can weaken the battery, causing hard starting.

Seat Heaters, Power Windows

Power Windows

DRIVER'S WINDOW SWITCH

MAIN SWITCH

The windows will operate for up to 10
minutes after you turn off the ignition switch. Opening either front door cancels this function.

Turn the ignition switch to the ON (II) position to raise or lower any window. To open a window, push the switch down and hold it. Release the switch when you want the window to stop. Pull back on the switch and hold it to close the window.

Closing a power window on someone's hands or fingers can cause serious injury.

Make sure your passengers are away from the windows before closing them.

AUTO － To open either front window fully, push the window switch firmly down to the second detent, then release it. The window automatically goes down all the way. To stop the window from going all the way down, pull back on the window switch briefly.

CONTINUED 149

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

AUTO REVERSE － If either front window senses any obstacle while it is closing automatically, it will reverse direction and then stop. To close the window, remove the obstacle, then use the window switch again. Auto reverse stops sensing when the window is almost closed. You should always check that all passengers and objects are away from the window before closing it.

If your vehicle's battery is disconnected or goes dead, or the driver's window fuse is removed, the AUTO function may be disabled. If the AUTO function is disabled, the power window system will need to be reset after reconnecting the battery or installing the fuse. 1. Start the engine. Push down and hold the driver's window switch until the window is fully open.

2. Pull and hold the driver's window

switch to close the window completely, then hold the switch for about 2 seconds.

If the power windows do not operate properly after resetting, have your vehicle checked by your dealer.

Power Windows

To close either front window fully, pull back the window switch firmly to the second detent, then release it. The window automatically goes all the way up. To stop the window from going all the way up, push down on the window switch briefly. When you push the MAIN switch in, the switch is off, and the passengers' windows cannot be raised or lowered. To cancel this feature, push on the switch again to get it to pop out. Keep the MAIN switch pushed in when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally.

150

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Opening the Windows and Moonroof with the Remote Transmitter You can open all of the windows and the moonroof from outside with the remote transmitter. 1. Press the UNLOCK button once to

unlock the driver's door.

2. Press the UNLOCK button a

second time, and hold it. All the doors unlock, and all four windows and moonroof start to open. To stop the windows and moonroof, release the button.

3. To open the windows and

moonroof further, press the button again (within 10 seconds of step 1) and hold it. If the windows and the moonroof stop before the desired position, repeat steps 1 and 2.

You cannot close the windows or the moonroof with the remote transmitter.

Opening/Closing the Windows and Moonroof with the Key

You can open and close the windows and moonroof with the key in the driver's door lock. To open: 1. Insert the key in the driver's door

lock.

2. Turn the key clockwise, then

release it.

Power Windows

3. Turn the key clockwise again, and

hold it. All four windows and the moonroof start to open. To stop the windows and the moonroof, release the key.

4. To open the windows and the

moonroof further, turn and hold the key again (within 10 seconds of step 2).

To close: 1. Insert the key in the driver's door

lock.

2. Turn the key counterclockwise,

then release it.

3. Turn the key counterclockwise

again, and hold it. All four windows and the moonroof start to close. To stop the windows and the moonroof, release the key.

CONTINUED 151

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Moonroof

Power Windows, Moonroof

4. To close the windows and the

moonroof further, turn and hold the key again (within 10 seconds of step 2). Auto reverse does not work when closing the windows and moonroof with the key.

NOTE: If the windows and the moonroof stop before the desired position, repeat steps 2 and 3.

MOONROOF SWITCH

To open the moonroof fully, pull back the moonroof switch firmly. The moonroof opens all the way. To stop the moonroof from opening fully, push the switch briefly.

To tilt up the moonroof, push on the center of the moonroof switch. To stop the moonroof from tilting up fully, push the switch briefly. To close the moonroof fully, firmly push the moonroof switch forward, then release it. The moonroof automatically closes all the way. To stop the moonroof from closing, push the switch briefly. To open or close the moonroof partially, pull back or push forward the moonroof switch lightly and hold it. The moonroof will stop when you release the switch.

152

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Auto Reverse If the moonroof runs into any obstacle while it is closing automatically, it will reverse direction, and then stop. To close the moonroof, remove the obstacle, then use the moonroof switch again. Auto reverse stops sensing when the moonroof is almost closed. You should always check that all passengers and objects are away from the moonroof before closing it.

Opening or closing the moonroof on someone's hands or fingers can cause serious injury.

Make sure all hands and fingers are clear of the moonroof before opening or closing it.

Moonroof, Parking Brake

You can open and close the moonroof for up to 10 minutes after you turn off the ignition switch. Opening either front door cancels this function.

Parking Brake

RELEASE HANDLE

If you try to open the moonroof in below-freezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or its motor.

PARKING BRAKE PEDAL

To apply the parking brake, push the pedal down with your foot. To release it, pull the release handle fully. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page 65). You will also see a ‘‘RELEASE PARKING BRAKE’’ message on the multi-information display (see page 81).

CONTINUED 153

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Parking Brake, Mirrors

Driving the vehicle with the parking brake applied can damage the rear brakes and axles. A beeper will sound if the vehicle is driven with the parking brake on.

Mirrors Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.

154

SENSOR

INDICATOR

AUTO BUTTON

The inside mirror can automatically darken to reduce glare. To turn on this feature, press the button on the bottom of the mirror. The AUTO indicator comes on as a reminder. When it is on, the mirror darkens when it senses the headlights of a vehicle behind you, then returns to normal visibility when the lights are gone. Press the button again to turn off this feature.

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Adjusting the Power Mirrors

There is also a sensor on the back of the mirror. Items hung on the mirror may block this sensor and affect its performance.

SELECTOR SWITCH

1. Turn the ignition switch to the ON

(II) position.

2. Move the selector switch to L

(driver's side) or R (passenger's side).

Mirrors

3. Push the appropriate edge of the

adjustment switch to move the mirror right, left, up, or down.

4. When you finish, move the

selector switch to the center (off) position. This turns the adjustment switch off to keep your settings.

CONTINUED 155

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Mirrors

Reverse Tilt Door Mirror Both outside door mirrors have a reverse tilt feature. When in reverse, the selected mirror will tilt down slightly to improve your view as you parallel park. Shifting out of reverse will return the mirror to its their original position. ● To tilt the driver's mirror, place the selector switch in the left position.

● To tilt the passenger's mirror,

place the switch in the right position.

● To turn the feature off, place the

switch in the center position. Outside mirror positions can be stored in the driving position memory system (see page 157).

156

Heated Mirrors

HEATED MIRROR BUTTON

The outside mirrors are heated to remove fog and frost. With the ignition switch in the ON (II) position, turn on the heaters by pressing the button. The indicator in the button comes on as a reminder. Press the button again to turn the heaters off. Pressing this button also turns the rear window defogger on and off.

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Your vehicle has a memory feature for the steering wheel, driver's seat, and outside mirror positions. Seat, except for power lumbar, steering wheel and outside mirror positions can be stored in separate memories. You select a memorized position by pushing the appropriate button or using the appropriate remote transmitter (Driver 1 or Driver 2). For more information see page 139.

Driving Position Memory System

Storing a Driving Position in Memory Store a driving position only when the vehicle is parked. 1. Turn the ignition switch to the ON (II) position. You cannot add a new driving position to the memory unless the ignition switch is in the ON (II) position. You can recall a memorized position with the ignition switch in any position. 2. Adjust the seat to a comfortable

position (see page 140). Adjust the steering wheel to a comfortable position (see page 124). Adjust the outside mirrors for best visibility (see page 155).

MEMORY BUTTONS

MEMO BUTTON

3. Press and release the MEMO

button on the control panel. You will hear a beep. Immediately press and hold one of the memory buttons (1 or 2) until you hear two beeps. The indicator in the memory button will come on. The current positions of the driver's seat, steering wheel, and outside mirrors are now stored.

CONTINUED 157

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Driving Position Memory System

Doing any of the following after pressing the MEMO button will cancel the storing procedure. ● Not pressing a memory button

within 5 seconds.

● Readjusting the seat position. ● Readjusting the outside mirror

position.

Each memory button stores only one driving position. Storing a new position erases the previous setting stored in that button's memory. If you want to add a new position while retaining the current one, use the other memory button.

Selecting a Memorized Position To select a memorized position, do this: 1. Make sure the vehicle is parked. 2. Press the desired memory button (1 or 2) until you hear a beep, then release the button.

The system will move the seat, steering wheel, and outside mirrors to the memorized positions. The indicator in the selected memory button will flash during movement. When the adjustments are complete, you will hear two beeps, and the indicator will remain on. To change the ‘‘MEMORY POSITION LINK’’ setting, see page 98.

To stop the system's automatic adjustment, do any of these actions: ● Press any button on the control

panel: MEMO, 1, or 2.

● Push any of the adjustment

switches for the seat.

● Shift out of Park. ● Adjust the outside mirrors. If desired, you can use the adjustment switches to change the positions of the seat, steering wheel or outside mirrors after they are in their memorized position. If you change the memorized position, the indicator in the memory button will go out. To keep this driving position for later use, you must store it in the driving position memory.

158

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Light Control Switch

DOOR ACTIVATED POSITION

OFF

ON

The light control switch has three positions: OFF, Door Activated, and ON. WhentheswitchisintheOFFposition: ● The individual door lights or the tailgate lights will operate when a door or the tailgate is opened.

● The individual map lights in the front can be turned on and off by pressing the lenses.

● The individual map lights in the second row and the cargo area light in the third row cannot be turned on.

Whentheswitchisinthedooractivated position: ● The individual map lights in the front and second rows come on when any door or the tailgate is opened, or when the remote transmitter is used to unlock the doors (see page 135). When the doors and the tailgate are closed, each light can be turned on and off by pushing the lens.

● The cargo area light comes on when any door or the tailgate is opened if the light control switch is in the door activated (center) position. When the doors and the tailgate are closed, the cargo area light can be turned on with the switch in the light.

Interior Lights

After all doors are closed tightly, the lights dim slightly, then fade out in about 30 seconds. To change the ‘‘INTERIOR LIGHT DIMMING TIME’’ setting, see page 101. With any door or the tailgate left open, the lights stay on about 3
minutes, then go out. The lights also come on when the key is removed from the ignition switch.

CONTINUED 159

2009 MDX 08/06/06 16:58:07 09 ACURA MDX MMC North America Owner's M 50 31STX620 enu

Interior Lights

Whenthelightcontrolswitchisinthe ONposition: ● All the individual map lights come

on and stay on as long as the switch remains in the ON position.

● The cargo (3rd row) area light comes on if the switch is in the door activated position.