2012 Volvo S80 Owners Manual

"Passenger airbag off" symbol near the rear-view mirror is illuminated (on vehicles equipped with Occupant Weight Sensor). If the severity of an accident were to cause the airbag to inflate, this could lead to serious injury or death to a child seated in this posi- tion.

3. Fasten the seat belt by inserting the latch plate into the buckle (lock) until a distinct click is audible.

Fasten the seat belt

``

41

01 Safety

01

Infant seats

Pull out the shoulder section of the seat belt 4. Pull the shoulder section of the seat belt

out as far as possible to activate the belt's automatic locking function.

Ensure that the seat is securely in place 6. Push and pull the infant seat along the seat belt path to ensure that it is held securely in place by the seat belt.

NOTE

WARNING

The locking retractor will automatically release when the seat belt is unbuckled and allowed to retract fully.

It should not be possible to move the child restraint (child seat) more than 1 in. (2.5 cm) in any direction along the seat belt path.

5. Press the infant seat firmly in place, let the

seat belt retract and pull it taut. A sound from the seat belt retractor's automatic locking function will be audible at this time and is normal. The seat belt should now be locked in place.

The infant seat can be removed by unbuckling the seat belt and letting it retract completely.

42

Securing a convertible seat with a seat belt

Route the seat belt through the convertible seat

Do not place the convertible seat in the front pas- senger's seat

NOTE

Refer to pages 46 and 47 for information on securing a child restraint using ISOFIX/ LATCH lower anchors and/or top tether anchorages.

Convertible seats can be used in either a for- ward or rearward-facing position, depending on the age and size of the child.

WARNING

Always use a convertible seat that is suita- ble for the child's age and size. See the con- vertible seat manufacturer's recommenda- tions.

1. Place the convertible seat in the rear seat

of the vehicle.

01 Safety

Convertible seats

01

WARNING

• A small child's head represents a con- siderable part of its total weight and its neck is still very weak. Volvo recom- mends that children up to age 4 travel, properly restrained, facing rearward. In addition, Volvo recommends that chil- dren should ride rearward facing, prop- erly restrained, as long as possible.

• Convertible child seats should be instal-

led in the rear seat only.

• A rear-facing convertible seat should not

be positioned behind the driver's seat unless there is adequate space for safe installation.

2. Attach the seat belt to the convertible seat

according to the manufacturer's instruc- tions.

``

43

01 Safety

01

Convertible seats

time and is normal. The seat belt should now be locked in place.

Fasten the seat belt 3. Fasten the seat belt by inserting the latch plate into the buckle (lock) until a distinct click is audible.

4. Pull the shoulder section of the seat belt

out as far as possible to activate the belt's automatic locking function.

NOTE

The locking retractor will automatically release when the seat belt is unbuckled and allowed to retract fully.

5. Press the convertible seat firmly in place, let the seat belt retract and pull it taut. A sound from the seat belt retractor's auto- matic locking function will be audible at this

Ensure that the seat is securely in place

Pull out the shoulder section of the seat belt 6. Push and pull the convertible seat along the seat belt path to ensure that it is held securely in place by the seat belt.

WARNING

It should not be possible to move the child restraint (child seat) more than 1 in. (2.5 cm) in any direction along the seat belt path.

The convertible seat can be removed by unbuckling the seat belt and letting it retract completely.

WARNING

A child seat should never be used in the front passenger seat of any vehicle with a front passenger airbag – not even if the "Passenger airbag off" symbol near the rear-view mirror is illuminated. If the severity of an accident were to cause the airbag to inflate, this could lead to serious injury or death to a child seated in this position.

44

Securing a booster cushion

Position the child correctly on the booster cushion Booster cushions are recommended for chil- dren who have outgrown convertible seats. 1. Place the booster cushion in the rear seat

of the vehicle.

2. With the child properly seated on the

booster cushion, attach the seat belt to or around the cushion according to the man- ufacturer's instructions.

3. Fasten the seat belt by inserting the latch plate into the buckle (lock) until a distinct click is audible.

Positioning the seat belt 4. Ensure that the seat belt is pulled taut and

fits snugly around the child.

WARNING

• The hip section of the three-point seat belt must fit snugly across the child's hips, not across the stomach.

• The shoulder section of the three-point seat belt should be positioned across the chest and shoulder.

• The shoulder belt must never be placed

behind the child's back or under the arm.

01 Safety

Booster cushions

01

45

01 Safety

01

ISOFIX/LATCH lower anchors

Using the ISOFIX/LATCH lower child seat anchors

Lower anchors for ISOFIX/LATCH-equipped child seats are located in the rear, outboard seats, hidden below the backrest cushions. Symbols on the seat back upholstery mark the anchor positions as shown. To access the anchors, kneel on the seat cushion and locate the anchors by feel. Always follow your child seat manufacturer's installation instructions, and use both ISOFIX/LATCH lower anchors and top tethers whenever possible.

To access the anchors 1. Put the child restraint in position. 2. Kneel on the child restraint to press down the seat cushion and locate the anchors by feel.

46

3. Fasten the attachment on the child

restraint's lower straps to the ISOFIX/ LATCH/LATCH lower anchors.

4. Firmly tension the lower child seat straps according to the manufacturer's instruc- tions.

WARNING

Volvo's ISOFIX/LATCH anchors conform to FMVSS/CMVSS standards. Always refer to the child restraint system's manual for weight and size ratings.

NOTE

• The rear seat's center position is not equipped with ISOFIX/LATCH lower anchors. When installing a child restraint in this position, attach the restraint's top tether strap (if it is so equipped) to the top tether anchorage point and secure the restraint with the vehicle's center seat belt.

• Always follow your child seat manufac- turer's installation instructions, and use both ISOFIX/LATCH lower anchors and top tethers whenever possible.

Fasten the attachment correctly to the ISOFIX/ LATCH lower anchors

WARNING

• Be sure to fasten the attachment cor- rectly to the anchor (see the illustration). If the attachment is not correctly fas- tened, the child restraint may not be properly secured in the event of a colli- sion.

• The ISOFIX/LATCH lower child restraint anchors are only intended for use with child seats positioned in the outboard seating positions. These anchors are not certified for use with any child restraint that is positioned in the center seating position. When securing a child restraint in the center seating position, use only the vehicle's center seat belt.

Child restraint anchorages

not equipped with lower tether straps, or the restraint is used in the center seating position, follow instructions for securing a child restraint using the Automatic Locking Retractor seat belt (see page 37).

6. Firmly tension all straps. Refer also to the child seat manufacturer's instructions for information on securing the child seat.

Your Volvo is equipped with child restraint top tether anchorages in the rear seat. They are located on the rear parcel shelf.

Securing a child seat 1. Place the child restraint on the rear seat. 2. Fold up the plastic cover over the anchor-

age to be used.

3. Route the top tether strap under the head

restraint and attach it to the anchor.

4. Fold down the outboard head restraints or

lower the center head restraint for easier access to the ISOFIX/LATCH anchor.

5. Attach lower tether straps to the lower ISO- FIX/LATCH anchors. If the child restraint is

01 Safety

Top tether anchors

01

WARNING

• Never route a top tether strap over the

top of the head restraint. The strap should be routed beneath the head restraint.

• Child restraint anchorages are designed to withstand only those loads imposed by correctly fitted child restraints. Under no circumstances are they to be used for adult seat belts or harnesses. The anchorages are not able to withstand excessive forces on them in the event of collision if full harness seat belts or adult seat belts are installed to them. An adult who uses a belt anchored in a child restraint anchorage runs a great risk of suffering severe injuries should a colli- sion occur.

• Do not install rear speakers that require the removal of the top tether anchors or interfere with the proper use of the top tether strap.

47

01 Safety

01

Child safety locks

Child safety locks

Child safety locks – rear doors The controls are located on the rear door jambs. Use the remote control's key blade or a screwdriver to adjust these controls.

The rear doors can only be opened from the outside when the slot is in the horizon- tal position. The rear doors can be opened from the inside when the slot is in the vertical posi- tion.

48

01 Safety

01

49

Remote key and key blade..................................................................... 52
Valet locking ........................................................................................... 59
Keyless drive........................................................................................... 60
Locks....................................................................................................... 63
Alarm....................................................................................................... 67

50

LOCKS AND ALARM

02 Locks and alarm

Remote key and key blade

Introduction Two remote keys or optional Personal Car Communicators (PCC) are provided with your vehicle. They enable you to unlock the doors and trunk, and also function as ignition keys to start the vehicle or operate electrical compo- nents. The remote keys contain detachable metal key blades for manually locking or unlocking the driver's door and the glove com- partment. Up to six remotes can be pro- grammed for use on the same vehicle. The PCCs have enhanced functionality com- pared with the standard remote key.

NOTE

In the remainder of this chapter, all referen- ces to the remote key also pertain to the PCC unless otherwise stated.

WARNING

Never leave the remote key in the ignition if children are to remain in the vehicle.

Detachable key blade Each remote key or PCC contains a detachable metal key blade for mechanically locking or unlocking the driver's door and the glove com- partment, and to enable the valet locking func- tion. See page 57 for more information on the key blade and see page 59 for information on

02

52

the valet locking function. The key blades have a unique code, which is used if new ones need to be produced. This code is available at an authorized Volvo retailer.

Loss of a remote key If either of the remote keys is lost, the other should be taken with the car to a Volvo retailer. As an anti-theft measure, the code of the lost remote key must be erased from the system.

NOTE

Additional or duplicate remote control keys can be obtained from any Authorized Volvo Retailer. You can also obtain additional or duplicate remote control keys from certain independ- ent repair facilities and locksmiths that are qualified to make remote control keys. Each key must be programmed to work with your vehicle. California Only: A list of independent repair facilities and/or locksmiths known to Volvo that can cut and code replacement keys can be found: • on the Volvo website at

http://www.volvocars.com/us/keys • by calling Volvo Customer Care at

1-800-458-1552

Number of keys. See

The number of registered keys for the vehicle can be found by pressing MY CAR and going into Information page 127 for a description of the menu sys- tem. USA-5WK49264
FCC ID:KR55WK49264 + Siemens VDO 5WK49236
FCC ID:KR55WK49236, 5WK49266
FCC ID:KR55WK49266 + Siemens VDO 5WK49233
FCC ID:KR55WK49233
This device complies with part 15 of the FCC rules and RSS-210. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause undesired operation. Canada-5WK49264
IC:267T-5WK49264 + Siemens VDO 5WK49236
IC:267T-5WK49236, 5WK49266
IC:267T-5WK49266 + Siemens VDO 5WK49233
IC:267T-5WK49233

02

02 Locks and alarm

Remote key and key blade

confirmation light by pressing OK/ MENU.

• To activate audible confirmation: go to

Lock

Car settings

Settings settings and select Audible confirmation by pressing OK/MENU. See page 127 for a description of the menu system.

Immobilizer (start inhibitor) Each of the keys supplied with your vehicle contains a coded transponder. The code in the key is transmitted to an antenna in the ignition slot where it is compared to the code stored in the start inhibitor module. The vehicle will start only with a properly coded key. If you misplace a key, take the other keys to a trained and qualified Volvo service technician for reprog- ramming as an anti-theft measure. The follow- ing messages (which may appear in the instru- ment panel display) are related to the immobil- izer:

Operation is subject to the following condi- tions: (1) this device may not cause interfer- ence, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device.

Key memory: door mirrors and driver's seat The position of the side door mirrors and power driver's seat are stored in the remote keys when the vehicle is locked. The next time the driver's door is unlocked with the same remote key and the door is opened within 2 minutes, the power driver's seat and side door mirrors will automatically move to the position that they were in when the doors were most recently locked with the same remote key. See page 83 for more information. This feature can be activated or deactivated in the vehicle's menu by pressing MY CAR and going into Settings key memory. See page 127 for a description of the menu system. See also page 60 for information regarding vehicles with the optional keyless drive.

Car settings

Car

Confirmation when locking/unlocking the vehicle Settings can be made in the menu system for audible and visual confirmation when the vehi- cle has been locked or unlocked. With these

functions activated, the following will occur when the vehicle is locked/unlocked: Locking confirmation • The turn signals flash once, an audible sig- nal sounds and the door mirrors will fold* in.

Confirmation will only be given when all doors and the trunk are properly closed and locked.

NOTE

If you do not receive confirmation when locking the vehicle, check whether a door or the trunk is ajar, or if this feature has been turned off in the menu.

Unlocking confirmation • The turn signals will flash twice and the

door mirrors will fold* out.

Making a setting Different alternatives for locking/unlocking confirmation can be selected in the menus by pressing MY CAR on the center console con- trol panel. • To activate visual confirmation: go to

Car settings

Settings settings and select Door lock confirmation light and/or Unlock

Light

* Option/accessory, for more information, see Introduction.

``

53

02 Locks and alarm

Remote key and key blade

Message

Meaning

02

Insert car key

Car key not found

Immobilizer Try start again

Remote key not rec- ognized during start. Try to start the vehi- cle again.

PCC with keyless drive only. Remote key not recognized during start. Try to start the vehicle again. If the problem con- tinues, insert the remote key into the ignition slot and try to start the vehicle again.

Remote key fault during start. Contact an authorized Volvo workshop.

CAUTION

Never use force when inserting the remote key in the ignition slot. The vehicle cannot be started if the transponder is damaged.

USA–FCC ID: LTQWFS 125VO

This device complies with part 15 of the FCC rules. Operation is subject to the following con- dition: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfer- ence that may cause undesired operation. Canada–IC: 3659A-WFS125VO Operation is subject to the following condi- tions: (1) this device may not cause interfer- ence, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device. See page 109 for information on starting the vehicle.

Replacing the battery in the remote key The batteries should be replaced if: • The information symbol illuminates and

Low battery in remote control. Please change batteries. is shown in the display and/or

• if the locks do not react after several

attempts to unlock or lock the vehicle.

NOTE

The remote key's range is normally approx- imately 60 ft (20 m) from the vehicle.

See page 57 for information on replacing the battery.

Common functions: Remote key/ Personal Car Communicator (PCC)*

Personal Car Communicator (PCC)*

Lock

Unlock

Approach lighting

Trunk unlock/open

Panic alarm

Buttons on the remote

Lock – Press the Lock button on the

remote once to lock all doors and the trunk. The turn signals will flash once to confirm lock- ing.

Unlock – Press the Unlock button on the

remote once to unlock the driver's door.

54

* Option/accessory, for more information, see Introduction.

After a short pause, press the Unlock button a second time within 10 seconds to unlock the other doors and the trunk. This function can be changed so that all doors unlock at the same time by pressing My Car and going to Settings Lock settings setting. See page 127 for a description of the menu system.

Change doors unlock

Car settings

Approach lighting – As you approach the vehicle, press the button on the remote key to light the interior lighting, parking lights, license plate lighting and the lights in the door mir- rors*. These lights will switch off automatically after 30, 60 or 90 seconds. See page 127 for a description of the menu system.

Unlock/open trunk

Press once: This unlocks the trunk (but does not open it) and disarms the alarm and optional movement sensor (the alarm indicator light on the dashboard will go out). If the trunk is not opened within two minutes it will automatically relock and the alarm will be rearmed. Press twice: This both unlocks the trunk and pops it open slightly.

02 Locks and alarm

Remote key and key blade

NOTE

NOTE

Any excess weight (snow, etc.) on the trunk lid may prevent it from opening.

See also page 64 for information on opening the trunk from the passenger compartment. After closing, the trunk will not automatically relock. Press Lock to relock it and rearm the alarm.

Panic alarm – This button can be used to attract attention during emergency situations. To activate the panic alarm, press and hold this button for at least 3 seconds or press it twice within 3 seconds. The turn signals and horn will be activated. The panic alarm will stop auto- matically after 2 minutes and 45 seconds. To deactivate, wait approximately 5 seconds and press the button again. The Panic alarm button will not unlock the vehi- cle.

Buildings or other obstacles may interfere with the function of the remote key. The vehicle can also be locked or unlocked with the key blade, see page 57.

02

Unique functions—PCC*

Information button

Indicator lights

Range The remote key has a range of approximately 60 ft. (20 m) from the vehicle.

Pressing the information button provides cer- tain information about the vehicle with the help of the indicator lights.

Using the information button 1. Press the information button

* Option/accessory, for more information, see Introduction.

``

55

02 Locks and alarm

Remote key and key blade

02

2. All of the indicator lights will flash sequen- tially for approximately 7 seconds to indi- cate that the PCC is receiving information from the vehicle. If any of the buttons are pressed during this 7-second period, transmission of information to the PCC will be interrupted.

NOTE

If none of the indicator lights flash when the information button has been pressed sev- eral times from different places in relation to the vehicle, contact an authorized Volvo service technician.

The indicator lights provide information according to the illustration:

56

NOTE

• The approach lighting, panic alarm, and the functions controlled by the informa- tion button have a range of approxi- mately 300 ft (100 m) from the vehicle. • Radio waves, buildings or other obsta- cles may interfere with the function of the PCC.

If the vehicle does not provide confirmation when a button has been pressed, try moving closer and pressing the button again. Outside of the PCC´s range If the PCC is more than approximately 300 ft (100 m) from the vehicle when the information button is pressed, no new information will be received. The PCC most recently used to lock or unlock the vehicle will show the vehicle's most recently received status. The indicator lights will not flash when the information button is pressed while the PCC is out of range. If more than one PCC is used to lock/unlock the vehicle, only the one used most recently will show the correct locking status.

Steady green light: the vehicle is correctly locked. Steady yellow light: the vehicle is not locked. Steady red light: the alarm has been trig- gered. Both red lights flash alternatively: the alarm was triggered less than 5 minutes ago.

Range The PCC's lock and unlock functions have a range of approximately 60 ft. (20 m) from the vehicle.

NOTE

Removing the key blade

If none of the indicator lights illuminate when the information button is pressed, this may be because the most recent transmission between the vehicle and the PCC was inter- rupted or impeded by buildings or other objects.

Keyless drive Vehicles equipped with the optional Personal Car Communicator have the keyless drive function, see page 60 for detailed informa- tion.

Detachable key blade The key blade can be removed from the remote key. When removed, the key blade can be used to: • Lock/unlock the driver's door if the remote

key is not functioning properly

• Lock/unlock the glove compartment (see

page 64)

• Enable/disable the valet locking function

(see page 59)

• The trunk can be opened manually if nec-

essary (see page 64)

02 Locks and alarm

Remote key and key blade

wise approximately one-quarter turn to unlock the driver's door only.

02

NOTE

After unlocking the driver's door with the key blade, opening the door will trigger the alarm.

To disable the alarm: Insert the remote key in the ignition slot. This also applies to vehicles equipped with the optional keyless drive.

Slide the spring loaded catch to the side.

Pull the key blade straight out of the remote key.

Reinserting the key blade in the remote key 1. Hold the remote key with the slot for the

key blade up.

2. Carefully slide the key blade into its groove. 3. Gently press the key blade in the groove

until it clicks into place.

Unlocking the doors with the detached key blade Insert the key blade as far as possible in the driver's door lock. Turn the key blade clock-

Replacing batteries in the remote key/ PCC The battery/batteries in the remote key/PCC should be replaced if: • The information symbol lights up and a text

appears in the information display.

and/or • the vehicle's locks repeatedly do not react when a button on the remote key/PCC is pressed within approximately 60 ft (20 m) from the vehicle.

``

57

02 Locks and alarm

Remote key and key blade

Opening the remote key/PCC

Slide the spring loaded catch to the

side.

Pull the key blade straight out of the

remote key.

Insert a small screwdriver in the hole

behind the spring loaded catch and care- fully pry up the cover.

2.

3.

PCC (two batteries) 1. Use a screwdriver to pry out the old bat-

teries. Insert the first new battery with the (+) side upward. Insert the plastic spacer over the battery. Insert the second new battery on top of the plastic spacer, with the + side downward.

Re-assembling the remote key 1. Press the remote key's cover into place. 2. Hold the remote key with the slot for the

key blade up.

3. Carefully slide the key blade into its groove. 4. Gently press the key blade in the groove

until it clicks into place.

Old batteries should be properly recycled.

NOTE

Turn the remote key with the buttons upward so that the batteries do not fall out when the cover is removed.

Replacing the batteries

CAUTION

When handling batteries, avoid touching their contact surfaces as this could result in poor battery function in the remote key.

Note the position of the battery's (+) or (–) sides.

Battery type CR 2430, 3 V (one battery in the remote key, two batteries in the PCC)

2.

Remote key (one battery) 1. Use a screwdriver to pry out the old bat-

tery. Insert a new one with the (+) side down- ward.

02

58

Blocking access to the trunk

to block access to the trunk and glove com- partment for e.g., valet parking or when the vehicle is brought to the retailer for service.

With the valet locking function activated: • The vehicle's doors can be locked or

unlocked with the remote • The engine can be started • The glove compartment cannot be

unlocked

Normal locking/unlocking function

• Access to the trunk is blocked (the trunk lid

cannot be unlocked or opened with the remote, and the rear seat backrests cannot be lowered

Activating the valet locking function

Locking/unlocking points with valet locking acti- vated By utilizing the remote key with the key blade removed, the valet locking feature enables you

Insert the key blade in the glove compart- ment lock.

02 Locks and alarm

Valet locking

Turn the key blade180 degrees clockwise.

Remove the key blade from the lock. A message will appear in the instrument panel display.

02

Deactivating the valet locking function Turn the key blade 180 degrees counterclock- wise in the glove compartment lock to deacti- vate valet locking. See page 64 for information on locking the glove compartment normally, without activat- ing the valet locking function.

59

02 Locks and alarm

Keyless drive

02

Keyless drive* (models with Personal Car Communicator only)

Keyless locking and unlocking

Range of the keyless drive remote key–5 ft (1.5 meters) This system makes it possible to unlock and lock the vehicle without having to press any buttons on the Personal Car Communicators (PCC). It is only necessary to have a keyless drive remote key in your possession to operate the central locking system.

NOTE

• The gear selector must in the P position

before the vehicle can be locked and the alarm can be armed.

• The buttons on the keyless drive remote key can also be used to lock and unlock the vehicle, see page 54 for more infor- mation.

Both of the PCCs provided with the vehicle have the keyless function, and additional ones can be ordered. The system can accommo- date up to six PCCs. The red rings in the illustration indicate the area around the vehicle that is within range of the keyless drive antennas.

Unlocking the vehicle • A keyless drive remote key must be on the same side of the vehicle as the door to be opened, and be within 5 feet (1.5 meters) of the door's lock or the trunk (see the sha- ded areas in the illustration).

• Pull a door handle to unlock and open the door or press the trunk opening control on the trunk lid.

The number of doors that are unlocked at the same time can be set in the vehicle's menu system. Press MY CAR and go to Car settings

Lock settings

Keyless entry. See page

127 for a description of the menu system.

NOTE

If the PCC does not function normally (weak battery, etc.), the vehicle can be unlocked with the detachable key blade, see page 57.

Locking or unlocking the vehicle with the key blade

Keyless drive keyhole cover The driver's door on vehicles equipped with keyless drive can be locked or unlocked with the remote key's detachable key blade if nec- essary, see page 57 for information on remov- ing the key blade from the remote key. To access the keyhole in the driver's door:

60

* Option/accessory, for more information, see Introduction.

1. Press the key blade approx. 0.5 in. (1 cm) straight up in the hole on the underside of the keyhole cover. > The cover will come off due to the pres-

sure exerted when the key blade is pushed upward.

2.

Insert the key blade as far as possible in the driver's door lock. Turn the key blade to unlock the driver's door only. This will trig- ger the alarm. Press the remote key into the ignition slot to turn off the alarm.

3. Press the cover back into place after the

door has been unlocked.

Locking the vehicle

Models with keyless drive have a button on the outside door handles

02 Locks and alarm

Keyless drive

The doors and the trunk can be locked by pressing the lock button in any of the outside door handles.

See also page 83 for information on adjusting and storing the seat's position in the seat mem- ory.

02

Keyless drive information messages If all of the PCCs are removed from the vehicle while the engine is running or if the ignition is in mode II (see page 80) and all of the doors are closed, a message will appear in the instru- ment panel display and an audible signal will sound. When at least one PCC has been returned to the car, the message will be erased in the dis- play and the audible signal will stop when: • A door has been opened and closed • The PCC has been inserted in the ignition

slot

• The READ button (see page 125 for the

location of this button) has been pressed.

NOTE

On keyless drive vehicles, the gear selector must be in the Park (P) position, all doors and the trunk must be closed and the igni- tion must be switched off before the vehicle can be locked.

Keyless drive remote key and driver's seat/door mirror memory • When you leave the vehicle with a PCC in

your possession and lock any door, the position of the driver's seat and door mir- rors will be stored in the seat's memory.

• The next time a door is opened by a person with the same PCC in his/her possession, the driver's seat and door mirrors will auto- matically move to the position that they were in when the door was most recently locked.

NOTE

If several people carrying PCCs approach the vehicle at the same time, the driver's seat and door mirrors will assume the posi- tions they were in for the person who opens the driver's door.

``

61

02 Locks and alarm

Keyless drive

CAUTION

02

• Keyless drive remote keys should never

be left in the vehicle. In the event of a break-in, a remote found in the vehicle could make it possible to start the engine.

• Electromagnetic fields or metal

obstructions can interfere with the key- less drive system. Avoid placing the remote key near cellular phones, metal- lic objects or e.g., in a metal briefcase.

USA – FCC ID:KR55WK48952, KR55WK48964
NOTE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including inter- ference that may cause undesired operation. CAUTION Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Siemens VDO 5WK48891
Tested To Comply With FCC Standards

62

For Automobile Use Canada – IC:267T-5WK48952, 267T-5WK48964, 267T-5WK48891
NOTE This device complies with RSS -210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including inter- ference that may cause undesired operation. CAUTION Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.

Location of the keyless drive antennas

The keyless drive system has a number of antennas located at various points in the vehi- cle.

On the inside center of the rear bumper

Left rear door handle

Center of the parcel shelf, on the underside

Ceiling, above the center of the rear seat

Right rear door handle

Under the rear section of the center con- sole Under the front section of the center con- sole.

WARNING

People with implanted pacemakers should not allow the pacemaker to come closer than 9 inches (22 cm) to any of the keyless drive system's antennas. This is to help pre- vent interference between the pacemaker and the keyless drive system.

Locking and unlocking the vehicle

From outside the vehicle The remote key locks and unlocks all of the doors and the trunk. Before the vehicle can be locked from the out- side with the remote key, the driver's door must be closed. Any other door/trunk that is open will be locked and the alarm will be armed.

NOTE

Be sure the remote key is outside of the vehicle before the other doors/trunk are closed to help avoid locking the remote inside the vehicle.

If the vehicle is equipped with the optional key- less drive system, all doors/trunk must be closed before the vehicle can be locked. The first press on the unlock button unlocks the driver's door and a second press unlocks the other doors and the trunk (see also page 54). This setting can be changed in the menu sys- tem, see page 128. If the locks repeatedly do not react when the unlock button is pressed, it may be necessary to replace the batteries in the remote, see page 54. In this case the vehicle can be unlocked with the detachable key blade. See page 57.

02 Locks and alarm

Locks

From inside the vehicle (central locking button)

Locking • Press the lock button

doors have been closed.

after the front

02

to

to lock and

Central locking button The lock buttons on the door panel can be used to lock or unlock all doors and the trunk at the same time. Press unlock. Unlocking The vehicle can be unlocked from inside the vehicle in two ways: • By pressing the unlock button • The door can be unlocked by pulling the door handle once and opened by pulling the handle again.

• Each door can be locked individually with the lock button on the respective doors. The door must be closed first.

Alternative locking when parking The central locking button on the driver's door can also be used to lock the vehicle when you leave it. To do so: 1. Open the door. 2. Press the lock section of the button. 3. Close the door. This will lock the vehicle

completely and arm the alarm.

NOTE

Please be aware that locking the vehicle in this way makes it possible to lock the remote key in the passenger compartment. To help avoid this, lock the vehicle from the outside by pressing the lock button on the remote key. If the vehicle is locked using the central locking button, be sure that the remote key is in your possession before closing the door.

``

63

02 Locks and alarm

Locks

Automatic relocking If the doors are unlocked, the locks will auto- matically reengage (re-lock) and the alarm will rearm after 2 minutes unless a door or the trunk has been opened.

Automatic locking When the vehicle starts to move, the doors and trunk can be locked automatically. This feature can be turned on or off by pressing MY CAR and going to Car settings Lock settings

Automatic door locking. See page 127 for

a description of the menu system.

Glove compartment

on removing the key blade from the remote key.

Insert the key blade in the glove compart- ment lock. Turn the key blade 90 degrees clockwise.

Remove the key blade from the lock.

Locking/unlocking the trunk

will automatically relock and the alarm will be rearmed. Press twice: This both unlocks the trunk and pops it open slightly.

NOTE

Any excess weight (snow, etc.) on the trunk lid may prevent it from opening.

The alarm indicator light on the dashboard will go out to indicate that the alarm is not moni- toring the entire vehicle. The accessory move- ment and inclination sensors will be automati- cally disconnected. When the trunk is closed again (which has to be done manually), it will have to be relocked and the alarm rearmed by pressing the lock button on the remote key.

The glove compartment can only be locked and unlocked using the detachable key blade in the remote key. See page 57 for information

Trunk unlock button on the remote key Unlocking the trunk with the remote key ± Press the trunk unlock button on the

remote.

Press once: This unlocks but does not open the trunk. The trunk can then be opened by pressing the rubber plate near the trunk lock. If the trunk is not opened within two minutes it

02

64

Unlocking/opening the trunk from the passenger compartment

Unlocking the trunk with the key blade

± Press the button on the lighting panel (1) to

unlock and pop open the trunk

NOTE

The taillights will illuminate automatically for a short period when the trunk has been opened.

If the remote key is not functioning properly, the trunk can be unlocked with the detachable key blade. See page 57 for information on removing the key blade from the remote key. Pull out the cover over the trunk’s keyhole.

Unlock the trunk by inserting the key blade in the keyhole and turning a half turn coun- terclockwise as shown in the illustration.

02 Locks and alarm

Locks

Locking the trunk with the remote key ± Press the lock button on the remote, see

page 54

The alarm indicator on the dashboard will begin flashing to show that the vehicle is locked and that the alarm has been armed.

02

NOTE

• If the doors are locked while the trunk is

open, the trunk will remain unlocked until the vehicle is relocked by pressing the Lock button on the remote key. • On keyless drive vehicles, the gear

selector must be in the Park (P) position, all doors and the trunk must be closed and the ignition must be switched off before the vehicle can be locked.

``

65

WARNING

• Keep vehicle doors and trunk locked and keep keys out of a child’s reach. Unsupervised children could lock them- selves in an open trunk and risk injury. Children should be taught not to play in vehicles.

• On hot days, the temperature in the trunk or vehicle interior can rise very quickly. Exposure of people to these high temperatures for even a short period of time can cause heat-related injury or death. Small children are par- ticularly at risk.

02 Locks and alarm

Locks

Opening the trunk from the inside (U.S. models only)

02

Opening the trunk from the inside The vehicle is equipped with a florescent han- dle on the inside of the trunk lid, which can be used in an emergency situation to open the trunk from the inside. Pull the handle down to release the trunk lid. After use, the handle must be pushed back into its original position before the trunk can be closed. This handle is not intended to be used to anchor the trunk lid when long loads are being transported.

66

The alarm system The alarm is automatically armed whenever the vehicle is locked with the remote key or optional Personal Car Communicator. When armed, the alarm continuously monitors a number of points on the vehicle. The follow- ing conditions will trigger the alarm: • The hood is forced open. • The trunk is forced open • A door is forced open. • The ignition slot is tampered with. • An attempt is made to start the vehicle with

a non-approved key (a key not coded to the car's ignition).

• If there is movement in the passenger com-

partment (if the vehicle is equipped with the accessory movement sensor).

• The vehicle is lifted or towed (if the vehicle is equipped with the accessory inclination sensor).

• The battery is disconnected (while the

alarm is armed).

• The siren is disconnected when the alarm

is disarmed.

A message will appear in the information dis- play if a fault should occur in the alarm system. Contact a trained and qualified Volvo service technician.

NOTE

Do not attempt to repair any of the compo- nents in the alarm system yourself. This could affect the insurance policy on the vehicle.

The alarm indicator light

The status of the alarm system is indicated by the red indicator light on the dashboard (see illustration): • Indicator light off – the alarm is not armed • The indicator light flashes at one-second

intervals – the alarm is armed

• The indicator light flashes rapidly before the remote key is inserted in the ignition slot and the ignition is put in mode I—the alarm has been triggered.

02 Locks and alarm

Alarm

Arming the alarm ± Press the Lock button on the remote key. One long flash of the turn signals will con- firm that the alarm is armed.

02

Lock

Keyless entry. See page 127 for

Alarm confirmation settings can be changed in MY CAR, under Car settings settings a description of the menu system. USA FCC ID: MAYDA 5823(3) This device complies with part 15 of the FCC rules. Operation is subject to the following con- ditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interfer- ence that may cause undesired operation. Canada IC: 4405A-DA 5823(3) Movement sensor DA5823 by Dynex Operation is subject to the following conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired opera- tion of the device.

``

67

02 Locks and alarm

Alarm

02

Disarming the alarm ± Press the Unlock button on the remote key. > Two short flashes from the car's direc-

tion indicators confirm that the alarm has been deactivated and that all doors are unlocked.

Turning off (stopping) the alarm If the alarm is sounding, it can be stopped by pressing the Unlock button on the remote key or by inserting the remote key in the ignition slot. Two short flashes from the car's direction indicators confirm that the alarm has been turned off.

Other alarm-related functions

Automatic re-arming If the doors are unlocked, the locks will auto- matically reengage (re-lock) and the alarm will re-arm after 2 minutes unless a door or the trunk has been opened.

Audible/visual alarm signal • An audible alarm signal is given by a bat- tery powered siren. The alarm cycle lasts for 30 seconds.

• The visual alarm signal is given by flashing all turn signals for approximately 5 minutes or until the alarm is turned off.

68

Remote key not functioning If the remote key is not functioning properly, the alarm can be turned off and the vehicle can be started as follows: 1. Open the driver's door with the key blade (see page 57 for information on detaching the key blade). > This will trigger the alarm.

2.

Insert the remote key into the ignition slot (also on vehicles with the optional keyless drive). This will turn off the alarm.

3. Start the engine.

Reduced alarm function

Turning off the accessory alarm sensors In certain situations it may be desirable to turn off the accessory inclination and movement alarm sensors if, for example, you drive your vehicle onto a ferry where the rocking of the boat could trigger the alarm or if a pet is left in the vehicle with the doors locked. The vehicle's menu system is used for turning off these sensors (see page 127 for a descrip- tion of the menu system). 1. Go into the menu under Car settings. 2. Select Reduced Guard (Press OK/

MENU to choose).

3. Two alternatives are now available:

• Activate once. If this alternative is

selected, Reduced guard See manual will appear in the instrument panel display and the accessory incli- nation and movement alarm sensors will be deactivated when the vehicle is locked.

• Ask when exiting. If this alternative is selected, a message will appear in the center console display each time the engine is turned off. Press OK/MENU to accept and the accessory inclination and movement alarm sensors will be

deactivated when the vehicle is locked. Press EXIT to cancel.

4. Press OK/MENU and lock the vehicle. The next time the engine is started, the alarm system will be reset and Full guard will appear in the instrument panel display. The accessory inclination and movement alarm sensors will be reactivated. In either of the alternatives, if you prefer not to deactivate the accessory inclination and move- ment alarm sensors, do not make a choice in the menu or press EXIT and lock the vehicle.

02 Locks and alarm

Alarm

02

69

Instruments and controls........................................................................ 72
Ignition modes........................................................................................ 80
Seats....................................................................................................... 82
Steering wheel........................................................................................ 88
Lighting................................................................................................... 90
Wipers and washers................................................................................ 96
Power windows....................................................................................... 99
Mirrors................................................................................................... 101
Compass*.............................................................................................. 103
Power moonroof*.................................................................................. 104
HomeLink® Wireless Control System*.................................................. 106
Starting the engine................................................................................ 109
Transmission......................................................................................... 113
Brakes................................................................................................... 116
Parking brake........................................................................................ 119

70

* Option/accessory, for more information, see Introduction.

YOUR DRIVING ENVIRONMENT

03 Your driving environment

Instruments and controls

Instrument overview

03

72

Function

Menus and mes- sages, turn signals, high/low beams, trip computer

Cruise control

Horn, airbag

Main instrument panel

Page

127, 93, 90, 142

147

89, 22

73

Audio system/Blue- tooth hands-free controls

200, 229

START/STOP ENGINE button

Ignition slot

Hazard warning flashers

Door handle

80

80

93

–

Function

In-door control pan- els (power win- dows, mirrors, power child safety locks, central lock- ing button)

Menu controls, info- tainment and cli- mate control sys- tems

Center console but- tons

Gear selector

Controls for active chassis (Four-C)*

Page

99, 101, 48, 63

127, 200, 136

127

113

146

Wipers and washers

96, 97

Steering wheel adjustment

Parking brake

Hood opening con- trol

88

119

309

03 Your driving environment

Instruments and controls

Page

82

90, 264, 64

Function

Power seat* adjust- ment controls

Lighting panel, but- tons for opening fuel filler door and unlocking and opening the trunk

03

Information displays

Information displays in the instrument panel The information displays show information on some of the vehicle's functions, such as cruise control, the trip computer and messages. The information is shown with text and symbols.

* Option/accessory, for more information, see Introduction.

``

73

03 Your driving environment

Instruments and controls

More detailed information can be found in the descriptions of the functions that use the infor- mation displays.

Gauges

03

in the red area of the gauge. The engine management system will automatically prevent excessively high engines speeds. This will be noticeable as a pronounced unevenness in engine speed.

Indicator, information, and warning symbols

Gauges in the instrument panel

Speedometer

Fuel gauge. Please note that the fuel level indicator in the gauge moves from right to left as the amount of fuel in the tank decreases. The arrow indicates the side of the vehicle that the fuel filler door is on. See also the section on refueling beginning on page 262. See page 142 for more infor- mation on fuel level and consumption. The tachometer shows engine speed in thousands of revolutions per minute (rpm). Do not drive continuously with the needle

Indicator and warning symbols

High beam and turn signal indicators

Indicator and warning symbols

Information symbols

Indicator and warning symbols

Function check All indicator and warning symbols light up in ignition mode II or when the engine is started.

74

* Option/accessory, for more information, see Introduction.

When the engine has started, all the symbols should go out except the parking brake sym- bol, which only goes out when the brake is dis- engaged. If the engine does not start or if the function check is carried out in ignition mode II, all sym- bols go out after 5 seconds except the symbol for faults in the vehicle's emissions system and the symbol for low oil pressure. Certain symbols may not have their functions illustrated, depending on the vehicle's equip- ment.

Indicator and information symbols

Symbol

Description

Fault in the Active Bending Light (ABL)*system

Malfunction indicator light

Anti-lock brake system (ABS)

Rear fog light on

Stability system

Tire pressure monitoring sen- sor (TPMS)

03 Your driving environment

Symbol

Description

Low fuel level

Information symbol, see text in information display

High beam indicator

Left turn signal indicator

Right turn signal indicator

The stability system's Sport mode is activated.

Fault in the Active Bending Light

(ABL) system This symbol will illuminate if the there is a fault in the ABL system. See page 91 for more information about this system.

Malfunction Indicator Light

As you drive, a computer called On-Board Diagnostics II (OBDII) monitors your vehicle's engine, transmission, electrical and emission systems. The malfunction indicator (CHECK ENGINE) light will illuminate if the computer senses a

condition that potentially may need correcting. When this happens, please have your vehicle checked by a trained and qualified Volvo serv- ice technician as soon as possible. A malfunction indicator (CHECK ENGINE) light may have many causes. Sometimes, you may not notice a change in your car's behavior. Even so, an uncorrected condition could hurt fuel economy, emission controls, and drivabil- ity. Extended driving without correcting the cause could even damage other components in your vehicle. This light may illuminate if the fuel filler cap is not closed tightly or if the engine was running while the vehicle was refueled.

Canadian models are equipped with this

symbol.

Anti-lock Brake System (ABS)

warning light If the warning light comes on, there may be a malfunction in the ABS system (the standard braking system will still function). Check the system by: 1. Stopping in a safe place and switching off

the ignition.

2. Restart the engine. 3.

If the warning light goes off, no further action is required.

03

Instruments and controls

If the warning light remains on, the vehicle should be driven to a trained and qualified Volvo service technician for inspection, see page 116 for additional information.

Canadian models are equipped with this

symbol.

Rear fog light

This symbol indicates that the rear fog light (located in the driver's side tail light cluster) is on.

Stability system

This indicator symbol flashes when the DSTC (Dynamic Stability and Traction Control sys- tem) is actively working to stabilize the vehicle, see page 144 for more detailed information. Tire pressure monitoring system

(TPMS)* This symbol illuminates to indicate that tire pressure in one or more tires is low, see page 301 for detailed information.

Low fuel level

When this light comes on, the vehicle should be refueled as soon as possible. See page 262 for information about fuel and refueling.

Information symbol

The information symbol lights up and a text message is displayed to provide the driver with

* Option/accessory, for more information, see Introduction.

``

75

03 Your driving environment

Instruments and controls

necessary information about one of the vehi- cle's systems. The message can be erased and the symbol can be turned off by pressing the READ button (see page 125 for information) or this will take place automatically after a short time (the length of time varies, depending on the function affected). The information symbol may also illuminate together with other symbols.

High beam indicator

This symbol illuminates when the high beam headlights are on, or if the high beam flash function is used.

Left turn signal indicator

Right turn signal indicator

NOTE

• Both turn signal indicators will flash

when the hazard warning flashers are used.

• If either of these indicators flash faster than normal, the direction indicators are not functioning properly.

Sport mode

This symbol illuminates to indicate that the sta- bility system's Sport mode has been activated to help provide maximum tractive force, for

example when driving with snow chains, or driving in deep snow or loose sand.

Indicator and warning symbols

Symbol Description

Low oil pressure

Parking brake applied

SRS airbags

Seat belt reminder

Generator not charging