motor from operating if the clutch pedal is not depressed all the way down. The switch allows the vehicle to be driven out of difficult situations by cranking the engine with the clutch engaged.
126
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
SECTION 1– 7
OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference Using your audio system Audio remote controls Car audio system operating hints
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
128
129
150
152
127
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
Reference
Type 1: AM·FM radio/compact disc player (with compact disc changer controller)
Type 2: AM·FM radio/cassette player/com- pact disc player (with compact disc changer controller)
Type 3: AM·FM radio/cassette player/com- pact disc player with changer
128
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” to turn the audio system on and off. Push “AM”, “FM”, “FM1”, “FM2”, “TAPE”, “DISC” or “LOAD” to turn on that function without pushing “PWR·VOL”. To turn on the cassette or compact disc player, a cassette or compact disc must be loaded in the player. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “AM”, “FM”, “FM1”, “FM2”, “TAPE”, “DISC” or “LOAD” if the system is already on but you want to switch from one func- tion to another.
If another
TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange, and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another. YOUR RADIO ANTENNA To remove an antenna, carefully turn it counterclockwise.
YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should face to the right.
NOTICE
Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.
YOUR COMPACT DISC PLAYER (type 1 and type 2) When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The player will play from track 1 through the end of the disc. Then it will play from track 1 again.
NOTICE
Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.
129
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
8 cm (3 in.) compact disc singles
Type 1—
Your compact disc player does not need
an adaptor to play compact disc singles.
Compact disc singles are about 8 cm (3
in.)
than standard
discs.
After you eject a compact disc single, do
not insert a standard 12 cm (4.7 in.) disc
until “DISC” disappears from the display.
in diameter–smaller
NOTICE
Do not use an adaptor for compact disc singles—it could cause tracking errors or interfere with the ejection of compact discs.
Type 2— The player is intended for use with 12 cm (4.7 in.) discs only.
130
’03 TUNDRA_U (L/O 0301)
YOUR COMPACT DISC PLAYER WITH CHANGER (type 3) When you insert a disc, push the “LOAD” button and gently push the disc in with the label side up. (The player will auto- matically eject a disc if the label side is down.) This compact disc player can store up to six discs. The player will play from track 1 through the end of the disc. Then it will play from track 1 of the next disc. The player is intended for use with 12 cm (4.7 in.) discs only.
NOTICE
(cid:4) Do not stack up two discs for in- sertion, or it will cause damage to the compact disc auto changer. In- sert only one compact disc into slot at a time.
(cid:4) Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
—Controls and features
(cid:1)Type 1
Details of specific buttons, controls and features are described in the alphabetical list that follows.
131
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
(See
to preset and
1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The button number will appear on the display. To recall a preset station: Push the button for the station you want. The button num- ber and station frequency will appear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM”, “FM1” or “FM2” button.)
(Eject button)
the compact disc eject button
Push eject a compact disc.
to
132
(Reverse/Fast–forward button)
time
Push and hold “ ” (preset button 6) or “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONTROL (Tone and sound bal- ance adjustment function) Each “AUDIO push CONTROL” knob, the mode changes. To adjust the knob. BAS: Adjusts low–pitched tones. The dis- play ranges from –5 to 5. TRE: Adjusts high–pitched tones. The dis- play ranges from –5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7.
tone and balance,
turn
you
the
the
DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will display one of the following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up–side down). Clean the disc and re–insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over–current. Ask your Toyota dealer to inspect.
incorrectly
inserted
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
“CD OPEN”: The compact disc changer
lid of separate unit is open. Close the
compact disc changer lid.
If the malfunction still exists, take your
vehicle to your Toyota dealer.
(cid:2) DISC (cid:1)
With compact disc changer only—
Use these buttons to select a disc you
want to listen to.
Push “(cid:2)” (preset button 3) or “(cid:1)” (preset
button 4) until the number of the disc you
want to listen appears on the display.
FM1 FM2
Push the “FM1” or “FM2” button to turn on
the radio and select the FM band. “FM1”
or “FM2” will appear on the display. This
system allows you to set twelve FM sta-
tions, two for each of the preset button.
PWR·VOL (Power and Volume)
Push “PWR·VOL” to turn the audio system
on and off. Turn “PWR·VOL” to adjust the
volume.
in random order, or
the player will perform
RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset button 1). “ ” will appear on the display and the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) until you hear a beep. “ ” will ap- pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.
feature, push
random
the
track
RPT (Repeat) There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. “ ” will appear on the display. When the track ends, it will automatically replay. To turn off the repeat feature, push this button again. With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 2) until you hear a beep. “ ” will ap- pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. To turn off the repeat feature, push this button again.
133
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.
listening
Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. With compact disc changer only— Scanning the first tracks of all the discs in the magazine: Push the “SCAN” button until you hear a beep. “ ·SCAN” will appear on the dis- play and the player will scan the first track of the next disc. To stop scanning, push this button again. If the player has scanned all the discs, it will stop scan- ning.
the seek mode,
the radio finds and the next station up or down the
SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release “(cid:1)” or “(cid:2)” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “(cid:1)” or “(cid:2)” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.
134
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
to
to
title,
track
then back
TEXT This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.
’03 TUNDRA_U (L/O 0301)
135
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
(cid:1)Type 2
136
’03 TUNDRA_U (L/O 0301)
Details of specific buttons, controls and features are described in the alphabetical list that follows.
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
(See
to preset and
1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The button number will appear on the display. To recall a preset station: Push the button for the station you want. The button num- ber and station frequency will appear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM” button.)
(Eject button) the cassette
Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc.
’03 TUNDRA_U (L/O 0301)
(Program)
Compact disc player
” indicates the top side, “
Push “ ” (preset button 4) to select the other side of a cassette tape. The display indicates which side is currently ” selected (“ indicates the bottom side). Auto–reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.
feature: After
(Reverse/Fast–forward button)
Cassette player
” (preset button 6) to fast–for- Push “ ward a cassette tape. “FF” will appear on the display. Push “ ” (preset button 5) to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast–forward- ing, push “ ” or “TAPE” button. To stop the tape while it is rewinding, push “ ” or “TAPE” button. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast–forwards completely, the cassette will play the other side of the tape using the auto–reverse feature.
time
Push and hold “
” (preset button 6) or
“
” (preset button 5) to fast forward or
reverse within a compact disc. When you
release the button, the compact disc play-
er will resume playing.
AM
Push the “AM” button to turn on the radio
and select the AM band. “AM” will appear
on the display.
AUDIO CONTROL (Tone and sound bal-
ance adjustment function)
Each
“AUDIO
push
CONTROL” knob, the mode changes. To
adjust
the
knob.
BAS: Adjusts low–pitched tones. The dis-
play ranges from –5 to 5.
MID (access cab models): Adjusts mid–
pitched tones. The display ranges from –5
to 5.
TRE: Adjusts high–pitched tones. The dis-
play ranges from –5 to 5.
FAD: Adjusts the sound balance between
the front and rear speakers. The display
ranges from F7 to R7.
tone and balance,
turn
you
the
the
137
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
“CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer. (cid:2) DISC (cid:1) With compact disc changer only— Use these buttons to select the disc you want to listen to. Push “(cid:2)” (preset button 3) or “(cid:1)” (preset button 4) until the number of the disc you want to listen appears on the display. Dolby(cid:3) If you are listening to a tape that was recorded with Dolby(cid:3) B Noise Reduction, ” will push “ appear on the display. Push the button again to turn off Dolby(cid:3) B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used to re- cord the tape. : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation.
” (preset button 3). “
B NR*
FM Push the “FM” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each of the preset button. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc listen the tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset button 1). “ ” will appear on the display and the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again.
the player will perform
in random order, or
BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will display one of the six following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up–side down). Clean the disc and re–insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over–current. Ask your Toyota dealer to inspect.
incorrectly
inserted
138
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
random
feature, push
With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) until you hear a beep. “ ” will ap- pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again. RPT (Repeat) Cassette player Push “RPT” (preset button 2) while the track is playing. “ ” will appear on the display. When the track ends, it will automatically rewind and replay. To turn off feature, push this button again. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.
the repeat
the
track
Compact disc player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. “ ” will appear on the display. When the track ends, it will automatically replay. To turn off the repeat feature, push this button again. With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 2) until you hear a beep. “ ” will ap- pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. To turn off the repeat feature, push this button again.
SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.
139
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
listening
Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. With compact disc changer only— Scanning the first tracks of all the discs in the magazine: Push the “SCAN” button until you hear a beep. “ ·SCAN” will appear on the dis- play and the player will scan the first track of the next disc. To stop scanning, push this button again. If the player has scanned all the discs, it will stop scan- ning.
140
the seek mode,
the radio finds and the next station up or down the
SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release “(cid:1)” or “(cid:2)” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Cassette Player Use this button to skip up or down to locate a song or recording. You can select up to nine recordings (in- cluding current one). A blank space of at least 3 seconds is considered to be a start of a recording. When a beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken word, live, or classical recordings.
Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “(cid:1)” or “(cid:2)” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push the “TAPE” button to play a cassette tape.
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
to
to
title,
track
then back
TEXT This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.
’03 TUNDRA_U (L/O 0301)
141
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
(cid:1)Type 3
142
’03 TUNDRA_U (L/O 0301)
Details of specific buttons, controls and features are described in the alphabetical list that follows.
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
(See
to preset and
1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset button number will appear on the display. RDS stations will be preset to the buttons when you turn on the RDS. (See “RDS” button.) To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. This radio can store one AM, two FM and RDS stations for each button. (The display will show “FM TYPE” when you push “AM” or “FM” but- ton.)
“FM2” or
“FM1”,
“AM”,
’03 TUNDRA_U (L/O 0301)
(Eject button)
(Program)
Cassette player This button is used to eject a cassette. Compact disc player This button is used to eject one or all compact discs. To eject the current compact disc, push and release the compact disc eject button. To eject a specific disc, push “(cid:2)” (preset button 3) or “(cid:1)” (preset button 4) until the number of the disc you want to eject is displayed. Push and release the eject but- ton. To eject all discs at a time, press and hold the eject button until you hear a beep. The last compact disc played before pushing the button will be ejected first. If the ejected disc is not removed for a long time, the eject function will be cancelled.
” indicates the top side, “
Push “ ” (preset button 4) to select the other side of a cassette tape. The display indicates which side is currently ” selected (“ indicates the bottom side). Auto–reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.
feature: After
(Reverse/Fast–forward button)
Cassette player
” (preset button 6) to fast–for- Push “ ward a cassette tape. “FF” will appear on the display. Push “ ” (preset button 5) to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast–forward- ing, push “ ” or “TAPE” button. To stop the tape while it is rewinding, push “ ” or “TAPE” button. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast–forwards completely, the cassette will play the other side of the tape using the auto–reverse feature.
143
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will display one of the six following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up–side down). Clean the disc and re–insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over–current. Ask your Toyota dealer to inspect.
incorrectly
inserted
B NR*
“CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer. (cid:2) DISC (cid:1) Use these buttons to select a disc you want to listen to. Push “(cid:2)” (preset button 3) or “(cid:1)” (preset button 4) until the number of the disc you want to listen appears on the display. Dolby(cid:3) If you are listening to a tape that was recorded with Dolby(cid:3) B Noise Reduction, ” will push “ appear on the display. Push the button again to turn off Dolby(cid:3) B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used to re- cord the tape. : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation.
” (preset button 3). “
Compact disc player
Push and hold “ ” (preset button 6) or “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONTROL (Tone and sound bal- ance adjustment function) Each “AUDIO push CONTROL” knob, the mode changes. To adjust the knob. BAS: Adjusts low–pitched tones. The dis- play ranges from –5 to 5. MID: Adjusts mid–pitched tones. The dis- play ranges from –5 to 5. TRE: Adjusts high–pitched tones. The dis- play ranges from –5 to 5. FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7.
tone and balance,
time
turn
you
the
the
144
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
FM Push the “FM” button to turn on the radio and select the FM band. “FM1”, “FM2” or “FM TYPE” will appear on the display. This system allows you to set twelve FM and six RDS stations, three for each of the preset button. If the RDS is off or RDS stations are not preset to the preset buttons, “FM TYPE” will not appear on the display. LOAD This button is used to load the compact discs the compact disc player. This player can store up to six discs. To load one compact disc only, quickly push and release the button, then insert a compact disc. After the disc is loaded, the shutter of the slot will close. If no compact disc is inserted, the shutter will close after 15 seconds.
in
To load multiple compact discs, push and hold the button (until you hear a beep when the audio system is on), then insert the first compact disc. After the disc is loaded, the shutter of the slot will close. After a few seconds, the shutter will auto- matically open again so the next disc can be inserted. The same process can be applied for loading the rest of the discs. If the player is full of discs, “DISC FULL” will appear on the display. If no compact disc is inserted, the shutter will close after 15 seconds. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RDS (Radio Data System) Your audio system is equipped with Radio Data System (RDS). RDS station providing good reception is automatically selected if current reception worsens. The “RDS” button turns the RDS on and off. This button is operational except in AM mode.
turns on,
the radio starts
To turn on the RDS, push and hold this button until you hear a beep and “RDS” will appear on the display. At this time, the radio starts to search the RDS sta- tions and “RDS SEARCH” will flash on the display. Quickly push and release this button when the RDS to search “RDS the RDS stations and SEARCH” will flash on the display. When found, stations are “FOUND” and the number of the RDS sta- tions will appear on the display, and you will hear two beeps. The stations will be preset to the preset buttons. If the RDS stations can not be found, “NO RDS ST” will appear on the display and you will hear a beep, and the display returns to the previous mode. To turn the RDS off, push the button until you hear a beep again.
the RDS
145
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
in random order, or
RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset button 1). “ ” will appear on the display and the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) until you hear a beep. “ ” will ap- pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.
the player will perform
feature, push
random
the repeat
RPT (Repeat) Cassette player Push “RPT” (preset button 2) while the track is playing. “ ” will appear on the display. When the track ends, it will automatically rewind and replay. To turn off feature, push this button again. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly. Compact disc player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. “ ” will appear on the display. When the track ends, it will automatically replay. To turn off the repeat feature, push this button again.
track
the
Repeating a disc: Push and hold “RPT” (preset button 2) until you hear a beep. “ ” will ap- pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. To turn off the repeat feature, push this button again. SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.
146
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. Scanning the first tracks of all the discs in the magazine: Push the “SCAN” button until you hear a beep. “ ·SCAN” will appear on the dis- play and the first the player will scan track of the next disc. To stop scanning, push this button again. If the auto changer has scanned all it will stop scanning.
the discs,
listening
’03 TUNDRA_U (L/O 0301)
the seek mode,
the radio finds and the next station up or down the
SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release “(cid:1)” or “(cid:2)” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Cassette Player Use this button to skip up or down to locate a song or recording. You can select up to nine recordings (in- cluding current one). A blank space of at least 3 seconds is considered to be a start of a recording. When a beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken word, live, or classical recordings.
Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “(cid:1)” or “(cid:2)” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push the “TAPE” button to play a cassette tape.
147
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
in RDS
is operational only
TEXT Radio This button mode. When an RDS radio station transmits a text message, “TEXT” will be displayed. At this time, push the “TEXT” button to view the text message. The message display will be canceled if any button that affects the display is pushed. To view the mes- sage again, push this button again. After the entire message has been displayed, the message will disappear. The RDS audio system has memory to store three 64–character messages. To store a message in memory, push and hold the “TEXT” button until you hear a beep. If three messages are already stored in memory, the oldest message will be over- written by the new message. To recall a radio text message, push the “TEXT” button momentarily. This will dis- play the most recent message. Each push of the button will display messages in the order of most to least recent.
If no messages have been stored, or if there are no more messages to be re- called, “NO MESSAGE” will appear on the display, and the message display will be canceled. The message display will be canceled if you activate any function that affects the display. Compact disc player This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear.
then back
track
title,
to
to
the
“TRAF” button,
TRAF (Traffic) This button turns the traffic announcement (TA) feature on and off. This button is operational only in FM mode. By pushing “TRAF SEEK” will flash on the display and the radio will start seeking any traffic program station. When a traffic program station is found, “TRAF” will be displayed and you will hear a beep. After the traffic announcement program is over, the display returns to the previous mode. If no traffic program station is found, “NO TRAF INFO” appears on the display for a few seconds and the display returns to the previous mode. To cancel the traffic announcement, push this button again. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.
148
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
TYPE (Program Types) When you push the “TYPE” button while receiving an RDS station, the current pro- gram type appears on the display. Each time you push this button, the pro- gram type changes as in the following: (cid:2) ROCK (cid:2) EASY LIS (Easy listening) (cid:2) CLS/JAZZ (Classical music and Jazz) (cid:2) R&B (Rhythm and Blues) (cid:2) INFORM (Information) (cid:2) RELIGION (cid:2) MISC (Miscellaneous) (cid:2) ALERT (Emergency message)
149
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
Audio remote controls (steering switches)
’03 TUNDRA_U (L/O 0301)
Some parts of the audio system can be adjusted using the switches on the steer- ing wheel. Details of the specific switches, controls, and features are described below. 1. Volume control switch 2. “(cid:1)(cid:2)” switch 3. “MODE” switch
150
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
to
increase while
1. Volume control switch Push “+” to increase the volume. The vol- ume continues the switch is being pushed. Push “–” the volume. The to decrease volume continues to decrease while the switch is being pushed. 2. “(cid:1)(cid:2)” switch Radio This switch has the following features— To select a preset station: Quickly push and release the “(cid:1)” or “(cid:2)” side of the switch. Do this again to select the next preset station. To seek a station: Push and hold the “(cid:1)” or “(cid:2)” side of the switch until you hear a beep. Do this again to find the next station. If you push the switch on either side during the seek mode, seeking will be cancelled. Cassette player This switch has the following features— To skip to a different track in either direc- tion: Quickly push and release the “(cid:1)” or “(cid:2)” side of the switch. “FF 1” or “REW 1” will appear on the display.
Next, push either side of the track switch until the track you want to listen to is set. If you push the switch ten times, the skip function will turn off. (You can skip up to nine tracks at a time.) When counting the number of the tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two tracks before the song you are listening to, push the “(cid:2)” side of the switch three times. If you push the track switch further than you wanted to, push the other side of the switch. The in- creased or reduced. The track number you select is not valid if the tracks remaining on the current side of the cassette. (cid:2) When the tape reaches to the begin- ning, the player will automatically start playing that side.
track number will be
the number of
is higher
than
it
(cid:2) After the tape reaches to the end, the reverse and
player will automatically start playing the other side.
There must be at least 3 seconds of blank space between tracks for the track switch to work correctly. In addition, the feature may not work well with some spoken, live, or classical recordings. To fast–forward or reverse: Push and hold the “(cid:1)” side of the switch to fast–forward a cassette tape. “FF” will appear on the display. Push and hold the “(cid:2)” side of the switch to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast–forward- ing, push the “(cid:1)” side of the switch. To stop the tape while it is rewinding, push the “(cid:2)” side of the switch. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast–forwards completely, the cassette will play the other side of the tape using the auto–reverse feature. Compact disc player Use this switch to skip up or down to a different track in either direction. Quickly push and release the “(cid:1)” or “(cid:2)” side of the switch until the track you want to listen to is set. If you want to return to the beginning of the current track, push the “(cid:2)” side of the switch once, quickly.
151
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
With compact disc changer only— Push and hold the “(cid:1)” or “(cid:2)” side of the switch until the disc you want to listen to is set. 3. “MODE” switch Push “MODE” switch to select an audio mode. Each push changes the mode se- quentially if the desired mode is ready to use. To turn the audio system on, push the “MODE” switch. To turn the audio system off, push and hold the “MODE” switch until the system turns off.
Car audio system operating hints
NOTICE
To ensure correct audio system op- erations: (cid:4) Be careful not to spill beverages
over the audio system.
(cid:4) Do not put anything other than a cassette tape or Compact Disc into the slot.
(cid:4) The use of a cellular phone inside or near the vehicle may cause a noise from the speakers of the au- dio system which you are listening to. However, this does not indicate a malfunction.
RADIO RECEPTION Usually, a problem with radio reception does not mean there is a problem with your radio—it is just the normal result of conditions outside the vehicle. For example, nearby buildings and terrain can interfere with FM reception. Power lines or telephone wires can interfere with AM signals. And of course, radio signals have a limited range. The farther you are from a station, the weaker its signal will be. conditions change constantly as your vehicle moves.
In addition,
reception
signals are
Here are some common reception prob-
lems that probably do not indicate a prob-
lem with your radio:
FM
Fading and drifting stations—Generally, the
effective range of FM is about 40 km (25
miles). Once outside this range, you may
notice fading and drifting, which increase
with the distance from the radio transmit-
ter. They are often accompanied by distor-
tion.
Multi–path—FM
reflective,
making it possible for two signals to reach
your antenna at the same time.
If this
happens, the signals will cancel each oth-
er out, causing a momentary
flutter or
loss of reception.
Static and
fluttering—These occur when
signals are blocked by buildings, trees, or
other large objects. Increasing the bass
level may reduce static and fluttering.
the FM signal you
Station swapping—If
are
interrupted or weak-
is
ened, and there is another strong station
nearby on the FM band, your radio may
tune in the second station until the origi-
nal signal can be picked up again.
listening to
152
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
Use high–quality cassettes. (cid:2) Low–quality cassette tapes can cause many problems, including poor sound, inconsistent and constant auto–reversing. They can also get stuck or tangled in the cassette player.
playing
speed,
(cid:2) Do not use a cassette if it has been damaged or tangled or if its label is peeling off.
(cid:2) Do not leave a cassette in the player if you are not listening to it, especially if it is hot outside.
(cid:2) Store cassettes in their cases and out
of direct sunlight.
(cid:2) Avoid using cassettes with a total play-
ing time longer than 100 minutes (50
minutes per side). The tape used in
these cassettes is thin and could get
stuck or tangled in the cassette player.
they can
AM Fading—AM broadcasts are reflected by the upper atmosphere—especially at night. These reflected signals can interfere with those received directly from the radio sta- tion, causing the radio station to sound alternately strong and weak. Station interference—When a reflected sig- nal and a signal received directly from a radio station are very nearly the same frequency, interfere with each other, making it difficult to hear the broad- cast. Static—AM is easily affected by external sources of electrical noise, such as high tension power lines, lightening, or electri- cal motors. This results in static. CARING FOR YOUR CASSETTE PLAYER AND TAPES For the best performance for your cas- sette player and tapes: Clean the tape head and other parts regu- larly. (cid:2) A dirty
tape head or tape path can decrease sound quality and tangle your cassette to clean them is by using a cleaning tape. (A wet type is recommended.)
tapes. The easiest way
CARING FOR YOUR COMPACT DISC
PLAYER AND DISCS
(cid:2) Type 2 and 3—Your compact disc play-
er is intended for use with 12 cm (4.7
in.) discs only.
(cid:2) Extremely high temperatures can keep your compact disc player from working. On hot days, use the air conditioning to cool the vehicle interior before you listen to a disc.
(cid:2) Bumpy roads or other vibrations may to
cause your compact disc player skip.
(cid:2) If moisture gets into your compact disc player, you may not hear any sound even though your compact disc player appears the disc from the player and wait until it dries.
to be working. Remove
CAUTION
Compact disc players use an invisible laser beam which could cause hazard- ous if directed outside the unit. Be sure to operate the player correctly.
radiation exposure
153
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
(cid:2) Use only compact discs marked as shown above. The following products may not be playable on your compact disc player. Copy–protected CD CD–R (CD–Recordable) CD–RW (CD–Re–writable) CD–ROM
Special shaped discs
Labeled discs
NOTICE
To prevent damage to the player or changer, do not use special shaped, low quality or labeled discs such as those shown in the illustrations.
154
Low quality discs
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
Correct
Wrong
inserting
(cid:2) Handle compact discs carefully, espe- them. cially when you are them on the edge and do not Hold them. Avoid getting fingerprints bend on them, particularly on the shiny side. (cid:2) Dirt, scrapes, warping, pin holes, or other disc damage could cause the player to skip or to repeat a section of a track. (To see a pin hole, hold the disc up to the light.)
(cid:2) Remove discs from the compact disc player when you are not listening to them. Store them in their plastic cases away from moisture, heat, and direct sunlight.
To clean a compact disc: Wipe it with a soft, lint–free cloth that has been damp- ened with water. Wipe in a straight line from the center to the edge of the disc (not in circles). Dry it with another soft, lint–free cloth. Do not use a conventional record cleaner or anti–static device.
155
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
156
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
SECTION 1– 8
OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Controls Air flow selector settings Operating tips Instrument panel vents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
158
161
161
163
157
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
Controls
158
’03 TUNDRA_U (L/O 0301)
1. Fan speed selector 2. Temperature selector 3. Air flow selector 4. “A/C” button (on some models) 5. Air intake selector
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
’03 TUNDRA_U (L/O 0301)
Fan speed selector Turn the knob to adjust the fan speed—to the right to increase, to the left to de- crease. Temperature selector Turn the knob to adjust the temperature— to the right to warm, to the left to cool.
Air flow selector Turn the knob to select the vents used for air flow. 1. Panel—Air
flows mainly
from
the
4. Floor/Windshield—Air
the
the air
flow selector
flows mainly floor vents and windshield
to turns on
from vents. the Turning floor/windshield position the defogging function with the purpose of clearing the front view. This position allows the air intake to select FRESH automatically. This is to clean up the front view more quickly. It is recommended that you close the lower vent. For details about this, see “Instrument panel vents” in this section. Vehicles with “A/C” button— Press the “A/C” button for dehumidified heating or cooling. This setting clears the front view more quickly.
instrument panel vents.
2. Bi–level—Air flows from both the floor vents and the instrument panel vents. 3. Floor—Air flows mainly from the floor
vents. It is recommended that you close the lower vent. For details about this, see “Instrument panel vents” in this section.
159
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
5. Windshield—Air flows mainly from the
to
flow selector
windshield vents. the Turning the air windshield position turns on the defog- ging function with the purpose of clear- ing the front view. This position allows the air intake to select FRESH automatically. This is to clean up the front view more quickly. It is recommended that you close the lower vent. For details about this, see “Instrument panel vents” in this section. Vehicles with “A/C” button— Press the “A/C” button for dehumidified heating or cooling. This setting clears the front view more quickly.
For details about air flow selector settings, see “Air flow selector settings” described below.
160
’03 TUNDRA_U (L/O 0301)
Air intake selector The air intake selector button is used to switch the air intake FRESH mode that the system and draws outside air into RECIRCULATED mode that recirculates the air inside vehicle. To turn the air source to RECIRCULATED mode, press the button. The indicator will come on. To turn the air source to FRESH mode, press the button again. The indica- tor will go off. To prevent fogging up of the windshield, the air intake mode may change automati- cally to FRESH depending on the condi- tion of the air conditioning system. “A/C” button To turn on the air conditioning, press the “A/C” button. The “A/C” button indicator will come on. To turn the air conditioning off, press the button again. Vehicles with 2UZ–FE engine—If the “A/C” button indicator flashes, there is a prob- lem in the air conditioning system and the air conditioning automatically shuts off. If this happens, to a Toyota dealer for service.
take your vehicle
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
Air flow selector settings
’03 TUNDRA_U (L/O 0301)
Operating tips (cid:1) To cool off your Toyota after
it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.
(cid:1) Make sure the air intake grilles in front of the windshield are not blocked (by leaves or snow, for example).
(cid:1) On humid days, do not blow cold air on the windshield. The windshield could fog up because of the difference in air temperature on the inside and outside of the windshield.
(cid:1) Keep the area under the front seats clear to allow air to circulate through- out the vehicle.
for a minute
(cid:1) On cold days, set the fan speed to high the intake ducts of snow or moisture. This can reduce the amount of fogging on the windows.
to help clear
: See “Instrument panel vents” in this section. * : On some models
(cid:1) When driving on dusty roads, close all windows. If dust thrown up by the ve- hicle is still drawn into the vehicle after closing the windows, it is recommended that the air intake selector be set to FRESH and the fan speed selector to any setting except “OFF”.
161
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
(cid:1) If following another vehicle on a dusty road, or driving in windy and dusty conditions, it is recommended that the air intake selector be temporarily set to RECIRCULATE, which will close off the outside passage and prevent outside air and dust from entering the vehicle interior.
Heating For best results, set controls to:
Fan speed—Any setting except “OFF” Temperature—Towards WARM
(red zone)
Air intake—FRESH (outside air) Air flow—FLOOR Lower vent—CLOSED Air conditioning—OFF
for a
few minutes. To keep
(cid:1) For quick heating, select recirculated air the windows from fogging, select fresh af- ter interior has been warmed.
the vehicle
(cid:1) Press the “A/C” button on for dehumidi-
fied heating.
(cid:1) Choose floor/windshield air flow to heat the vehicle interior while defrosting or defogging the windshield.
162
’03 TUNDRA_U (L/O 0301)
Air conditioning For best results, set controls to:
Fan speed—Any setting except “OFF” Temperature—Towards COLD
(blue zone)
Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—ON
(cid:1) For quick cooling, move the air intake selector to recirculate for a few min- utes.
Ventilation For best results, set controls to:
Fan speed—Any setting except “OFF” Temperature—Towards COLD
(blue zone)
Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—OFF
Defogging The inside of the windshield For best results, set controls to:
Fan speed—Any setting except “OFF” Temperature—Towards WARM (red zone) to heat; COLD (blue zone) to cool
Air intake—FRESH (outside air) Air flow—WINDSHIELD Lower vent—CLOSED
Turning the air flow selector to the wind- shield or floor/windshield position turns on the defogging function with the purpose of clearing the front view. When turning the air flow selector to wind- shield or floor/windshield position, the air intake selects FRESH automatically. This is to clean up the front view more quickly. Vehicles with “A/C” button— Press for dehumidified heating or cooling. This setting clears the front view more quickly. (cid:1) On humid days, do not blow cold air on the windshield—the difference be- tween the outside and inside tempera- tures could make the fogging worse.
the “A/C” button
2003 TUNDRA from Jan. ’03 Prod. (OM34421U)
Defrosting The outside of the windshield For best results, set controls to:
Fan speed—Any setting except “OFF” Temperature—Towards WARM
(red zone)
Air intake—FRESH (outside air) Air flow—WINDSHIELD Lower vent—CLOSED
Turning the air flow selector to the wind- shield or floor/windshield position turns on the defrosting function with the purpose of clearing the front view. When turning the air flow selector to wind- shield or floor/windshield position, the air intake selects FRESH automatically. This is to clean up the front view more quickly. Vehicles with “A/C” button— Press for dehumidified heating or cooling. This setting clears the front view more quickly. (cid:1) To heat the vehicle interior while de- floor/
the windshield, choose
the “A/C” button
frosting windshield air flow.
’03 TUNDRA_U (L/O 0301)
Instrument panel vents
If air flow control is not satisfactory, check the instrument panel vents. The instrument panel vents may be opened or closed as shown. For removing frost or fog, it is recom- mended lower vent when using the “Floor”, “Floor/Windshield” or “Windshield” mode.
that you close