2011 Toyota Tacoma Owners Manual

∗: If equipped 331

3-6. Other interior features Floor mat

Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet.

Fix the floor mat in place using the retaining hooks (clips) pro- vided.

The shape of the retaining hooks (clips) and the fixing procedure of the floor mat for your vehicle may differ from those shown in the illustration. For details, refer to the floor mat retention clip installation instructions supplied with the clips.

CAUTION

Observe the following precautions. Failure to do so may cause the driver’s floor mat to slip, possibly interfering with the pedals while driving. An unexpectedly high speed may result or it may become difficult to stop the vehicle, leading to a serious accident. n When installing the driver’s floor mat

l Do not use floor mats designed for other models or different model year

vehicles, even if they are Toyota Genuine floor mats.

l Only use floor mats designed for the driver’s seat. l Always install the floor mat securely using the retaining hooks (clips) pro-

vided.

l Do not use two or more floor mats on top of each other. l Do not place the floor mat bottom-side up or upside-down.

332

CAUTION

n Before driving

3-6. Other interior features

l Check that the floor mat is securely fixed in the right place with all the pro- vided retaining hooks (clips). Be espe- cially careful to perform this check after cleaning the floor.

l With the engine stopped and the shift lever in P (automatic transmission) or N (manual transmission), fully depress each pedal to the floor to make sure it does not interfere with the floor mat.

333

3-6. Other interior features Luggage compartment features

Behind the rear seat (Double Cab models only)

Cargo net hooks (vehicles with sub woofer) Grocery bag hooks Flashlight holder Storage boxes Deck

Auxiliary boxes Tie-down cleats Deck hooks

334

Auxiliary boxes

Left side

3-6. Other interior features

Turn the knob counterclock- wise. Open the lid.

Right side (vehicles without 115V power outlet)

Turn the knob counterclock- wise. Open the lid.

Right side (vehicles with 115V power outlet)

Turn the knob counterclock- wise. Open the lid.

335

3-6. Other interior features

CAUTION

n Caution while driving

Keep the auxiliary boxes closed and locked. Injuries may result in the event of an accident or sudden braking.

Deck hooks

Deck hooks are provided for securing loose items.

CAUTION

n When not in use

Keep the deck hooks folded.

336

3-6. Other interior features

Tie-down cleats

The deck rail system enables you to insert and move tie-down cleats to their best location along deck rails to secure a load.

Locking plate Thumb wheel Tie-down cleat

n Installing the tie-down cleat

Loosen the thumb wheel in a counterclockwise motion, and depress the wheel so that the locking plate maintains 0.5 in. (12.7 mm) gap.

0.5 in. (12.7 mm)

Deck rail Detent Locking plate

337

3-6. Other interior features

338

Insert the locking plate into the deck rail, rotate the tie-down cleat 90°, and release the thumb wheel.

Slide the cleat to the closest detent in the rail system. You will feel that the locking plate snaps into a detent.

Tighten the thumb wheel in a clockwise motion until the clutch mechanism ratchets.

Check the tie-down cleat to con- firm that it is locked into a detent and securely mounted to the deck rail system.

3-6. Other interior features

CAUTION

n Tie-down cleat precautions

l Properly install and tighten the tie-down cleats into the deck rail system.

Failure to properly install and tighten the tie-down cleats can cause cargo to become unsecured. Unsecured cargo can cause injury when the vehi- cle is in motion.

l Properly secure all cargo to prevent shifting or sliding during driving.

Failure to properly secure cargo can cause injury when the vehicle is in motion.

l Applying loads at an angle to the tie-down cleat greater than 45° or loads greater than 220 lb. (100 kg) may cause damage to the deck, deck rail system, tie-down cleat and/or the cargo.

l Do not exceed a total tensile load of 440 lb. (200 kg) per deck rail. l Do not install more than the following number of tie-down cleats per deck

rail: • Side rail:

Short deck—Max. 3 locations Long deck—Max. 4 locations

• Headboard rail: Max. 3 locations

Storage boxes (Double Cab models only)

Storage box is designed to place things like bottles.

Right side (vehicles without sub woofer)

339

3-6. Other interior features

Left side

n Removing the separator

Remove the separator. It can be installed in various positions as required.

Flashlight holder (Double Cab models only)

Flashlight holder is designed to hold the flashlight securely.

340

3-6. Other interior features

n Removing the flashlight holder

Remove the flashlight holder. It can be installed in various positions as required.

Grocery bag hooks (Double Cab models only)

Grocery bag hook is designed to hang things like grocery bag.

NOTICE

n Grocery bag hook weight capacity

Do not hang any object heavier than 7 lb. (3 kg) on the grocery bag hooks.

341

3-6. Other interior features

Cargo net hooks (Double Cab models with sub woofer)

Cargo net hooks are designed to hang the factory-supplied cargo net.

NOTICE

n To prevent damage to the cargo net hook Do not hang items other than the cargo net.

342

3-6. Other interior features Garage door opener box∗

The garage door opener box is designed to store a garage door opener transmitter. n Storing the transmitter in the box

Pull the lid down while pushing the knob.

Remove fastener square.

the hook-and-loop

∗: If equipped 343

the paper strip Remove covering the adhesive on back side of square. Adhere the square to back side of the transmitter near the center.

Place the transmitter with fas- tener square facing inside of box into the box.

Make sure the transmitter but- ton is located above button pins.

Remove spacers from the center panel. Place one spacer on the pin that would be below trans- mitter button when the cover is closed. Close the cover.

3-6. Other interior features

344

3-6. Other interior features

n Operating the garage door opener transmitter

When the garage door opener transmitter is properly installed, you can operate the transmitter by pushing the button of the cover.

Push the button.

n If a garage door opener transmitter has wire clip for sun visor

This clip must be removed prior to adhe- sion of the fastener.

n If the center panel does not touch your garage door opener transmitter l Check to see if the spacer is on the cor-

rect pin.

l Attach another spacer to the top of orig- inal spacer. Check operation. If required, continue to add spacers until contact is achieved.

n To prevent the transmitter from clattering during driving

If the transmitter is clattering during driving, fill in a piece of felt or pad.

345

3-6. Other interior features

CAUTION

n Caution while driving

Keep the garage door opener box closed. Injuries may result in the event of an accident or sudden braking.

n To prevent an accident

Keep the remaining spacers away from the children.

346

3-6. Other interior features Compass (vehicles with accessory meter)

The compass on the accessory meter indicates the direction in which the vehicle is heading. n Operation

To turn the compass on or off, press the switch.

n Displays and directions

Display

NE SE SW NW

Direction

North

Northeast

East

Southeast

South

Southwest

West

Northwest

347

3-6. Other interior features

Calibrating the compass

Samoa: 5 Guam: 8 Saipan: 8

The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle.

If you cross over a map boundary shown in illustration, the compass will deviate. To obtain higher precision or perfect calibration, refer to the following.

n Deviation calibration

Stop the vehicle where it is safe to drive in a circle.

the switch until VAR

Press appears on the display.

Press the switch, and referring to the map above, select the number of the zone where you are. If the direction is displayed several seconds after adjustment, the calibration is complete.

348

3-6. Other interior features

n Circling calibration

Stop the vehicle where it is safe to drive in a circle.

the switch until CAL

Press appears on the display.

At this time, the compass display is locked in N.

Drive the vehicle at 5 mph (8 km/ h) or less in a circle until the direction is displayed.

If there is not enough space to drive in a circle, drive around the block until the direction is dis- played. When CAL goes off and the com- pass display returns to the normal mode, calibration is complete.

349

3-6. Other interior features

n Conditions unfavorable to correct operation

The compass may not show the correct direction in the following conditions: l The vehicle is stopped immediately after turning.

The compass does not adjust while the vehicle is stopped.

l The engine switch is turned off immediately after turning. l The vehicle is on an inclined surface. l The vehicle is in a place where the earth’s magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.).

l The vehicle has become magnetized.

(There is a magnet or metal object on or near the roof.)

l The battery has been disconnected.

CAUTION

n While driving the vehicle

Do not adjust the display. Be sure to adjust the display only when the vehicle is stopped.

n When doing the circling calibration

Be sure to secure a wide space, and watch out for people and vehicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.

350

3-6. Other interior features

NOTICE

n To avoid the compass malfunctions

Do not place magnets or any metal objects on or near the roof. Doing this may cause a malfunction of the compass sensor.

n To ensure normal operation of the compass

l Do not perform circling calibration of the compass in a place where the earth’s magnetic field is subject to interference by artificial magnetic fields. l During calibration, do not operate electric systems (power windows, etc.)

as they may interfere with the calibration.

351

3-6. Other interior features

352

4-1. Maintenance and care Cleaning and protecting the vehicle exterior

Perform the following to protect the vehicle and maintain it in prime condition.

l Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust. Wash the vehicle body using a sponge or soft cloth, such as a chamois.

l For hard-to-remove marks, use car wash soap and rinse thor-

oughly with water.

l Wipe away any water. l Wax the vehicle when the waterproof coating deteriorates. If water does not bead on a clean surface, apply wax when the vehicle body is cool.

n Automatic car washes

l Before washing the vehicle, do the following.

• Fold the mirrors back. • Remove the antenna.

l Brushes used in automatic car washes may scratch the vehicle surface

and harm your vehicle’s paint.

n High pressure car washes

Do not allow the nozzles of the car wash to come within close proximity of the windows. Before entering an automatic car wash, check that the fuel filler door on your vehicle is closed properly.

n Aluminum wheels (if equipped)

l Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint.

l Do not use detergent on the wheels when they are hot, for example after

driving for long distance in the hot weather.

l Wash detergent from the wheels immediately after use.

354

4-1. Maintenance and care

n Bumpers and side moldings

Do not scrub with abrasive cleaners.

CAUTION

n Caution about the exhaust pipe

Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.

NOTICE

n To prevent paint deterioration and corrosion on the body and compo-

nents (aluminum wheels etc.) l Wash the vehicle immediately in the following cases:

• After driving near the sea coast • After driving on salted roads • If you see coal tar or tree sap on the paint surface • If you see dead insects, insect droppings or bird droppings on the paint • After driving in an area contaminated with soot, oily smoke, mine dust,

iron powder or chemical substances

• If the vehicle becomes heavily soiled in dust or mud • If liquids such as benzene and gasoline are spilled on the paint surface If the paint is chipped or scratched, have it repaired immediately.

l To prevent the wheels from corroding, remove any dirt and store in a place

with low humidity when storing the wheels.

355

4-1. Maintenance and care

NOTICE

l Clean the drainage hole of the deck regularly.

If the drainage hole is stopped up, the water will not be able to flow, and it will cause rust.

n Cleaning the exterior lights

l Wash carefully. Do not use organic substances or scrub with a hard brush.

This may damage the surfaces of the lights.

l Do not apply wax on the surfaces of the lights.

Wax may cause damage to the lenses.

n Antenna installation and removal precautions

l Before driving, ensure that the antenna is installed. l When the antenna is removed, such as before entering an automatic car wash, make sure to store it in a suitable place so as not to lose it. Also, before driving, make sure to reinstall the antenna in its original position.

356

4-1. Maintenance and care Cleaning and protecting the vehicle interior

The following procedures will help protect your vehicle’s interior and keep it in top condition: n Protecting the vehicle interior

Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.

n Cleaning the leather areas

l Remove dirt and dust using a vacuum cleaner. l Wipe any excess dirt and dust with a soft cloth dampened with

diluted detergent. Use a diluted water solution of approximately 5% neutral wool deter- gent.

l Wring out any excess water from the cloth and thoroughly

wipe off all remaining traces of detergent.

l Wipe the surface with a dry, soft cloth to remove any remain- ing moisture. Allow the leather to dry in a shaded and venti- lated area.

n Synthetic leather areas

l Remove loose dirt using a vacuum cleaner. l Apply a mild soap solution to the synthetic leather using a

sponge or soft cloth.

l Allow the solution to soak in for a few minutes. Remove the

dirt and wipe off the solution with a clean, damp cloth.

n Caring for leather areas

Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle’s interior.

357

4-1. Maintenance and care

n Shampooing the carpets

There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. The excellent results are obtained when keeping the carpet as dry as possible.

n Seat belts

Clean with mild soap and lukewarm water using a cloth or sponge. Also check the belts periodically for excessive wear, fraying or cuts.

CAUTION

n Water in the vehicle

l Do not splash or spill liquid in the vehicle.

Doing so may cause the electrical components etc. to malfunction or catch fire.

l Do not get any of the SRS components or wiring in the vehicle interior wet.

(→P. 83) Electrical malfunction may cause the airbags to deploy or not function properly, resulting in death or severe injury.

n Cleaning the interior (especially instrument panel)

Do not use polish wax or polish cleaner. The instrument panel may reflect off the windshield, obstructing the driver’s view and leading to an accident, resulting in death or serious injury.

358

4-1. Maintenance and care

NOTICE

n Cleaning detergents

l Do not use organic substances such as benzene or gasoline, acidic or alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces.

l Do not use polish wax or polish cleaner. The instrument panel’s or other

interior part’s painted surface may be damaged.

n Preventing damage to leather surfaces

Observe the following precautions to avoid damage to and deterioration of leather surfaces. l Remove any dust or dirt on leather surfaces immediately. l Do not expose the vehicle to direct sunlight for extended periods of time.

Park the vehicle in the shade, especially during summer.

l Do not place items made of vinyl, plastic, or that contain wax on the uphol- stery, as they may stick to the leather surface if the vehicle interior heats up significantly.

n Water on the floor

Do not wash the vehicle floor with water. Vehicle systems such as the audio system may be damaged if water comes into contact with electrical components under the floor of the vehicle, and may also cause the body to rust.

359

4-2. Maintenance Maintenance requirements

To ensure safe and economical driving, day-to-day care and regular maintenance is essential. It is the owner’s responsibility to perform regular checks. Toyota recommends the following maintenance. n General maintenance

Should be performed on a daily basis. This can be done by your- self or by a Toyota dealer. n Scheduled maintenance

Should be performed at specified intervals according to the maintenance schedule. For details about maintenance items and schedules, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

n Do-it-yourself maintenance

You can perform some maintenance procedures yourself. Please be aware that do-it-yourself maintenance may affect war- ranty coverage. The use of Toyota Repair Manuals is recommended. For details about warranty coverage, see the separate “Owner’s Warranty Information Booklet”, “Owner’s Manual Supplement”.

n Repair and replacement

It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than Toyota dealer performs repairs, confirm the war- ranty coverage.

360

4-2. Maintenance

n Allow inspection and repairs to be performed by a Toyota dealer

l Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.

l Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.

CAUTION

n Warning in handling of battery

l Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.

l Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of Califor- nia to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.

l Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (→P. 384)

361

4-2. Maintenance General maintenance

Listed below are the general maintenance items that should be per- formed at the intervals specified in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice.

Engine compartment

Items

Battery Brake fluid Engine coolant Engine oil Exhaust system Power steering fluid

Radiator/condenser/hoses

Washer fluid

Check points

(→P. 384) Maintenance-free. (→P. 380) At the correct level? At the correct level? (→P. 379) At the correct level? (→P. 374) No fumes or strange sounds? At the correct level? (→P. 382) Not blocked with foreign matter? (→P. 380) At the correct level? (→P. 386)

362

4-2. Maintenance

Vehicle interior

Items

Check points

Accelerator pedal

Automatic transmission “Park” mechanism

Brake pedal

Brakes

Clutch pedal

Head restraints

Indicators/buzzers

Lights

Parking brake

Seat belts

Seats

• Moves smoothly (without uneven pedal effort or catching)? • Can the vehicle be hold securely on an incline with the shift lever in P? • Moves smoothly? • Does it have appropriate clear- ance and correct amount of free play? • Not pull to one side when applied? • Loss of brake effectiveness? • Spongy feeling brake pedal? • Pedal almost touches floor? • Moves smoothly? • Does it have correct amount of free play? • Move smoothly and lock securely? • Function properly? • Do all the lights come on? • Headlights aimed correctly? • Moves smoothly? • Can hold the vehicle securely on an incline? • Does the seat belt system oper- ate smoothly? • Are the belts undamaged? • Do the seat controls operate properly?

363

4-2. Maintenance

Items

Steering wheel

Vehicle exterior

Check points

• Moves smoothly? • Has correct free play? • No strange noises?

Doors Engine hood

Fluid leaks

Tire

Items

Check points

• Operate smoothly? • The lock system works properly? • Is there any leakage after park- ing? • Inflation pressure is correct? • Tire surfaces not worn or dam- aged? • Tires rotated according to the maintenance schedule? • Wheel nuts are not loose?

CAUTION

n If the engine is running

Turn the engine off and ensure that there is adequate ventilation before per- forming maintenance checks.

364

4-2. Maintenance Emission inspection and maintenance (I/M) programs

Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system moni- tors the operation of the emission control system. n If the malfunction indicator lamp comes on

The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle.

n Your vehicle may not pass the I/M test:

l When the battery is disconnected or discharged

Readiness codes that are set during ordinary driving are erased. Also, depending on your driving habits, the readiness codes may not be completely set.

l When the fuel tank cap is loose

The malfunction indicator lamp comes on as a temporary mal- function and your vehicle may not pass the I/M test.

n When the malfunction indicator lamp goes off after several

driving trips The error code in the OBD system will not be cleared unless the vehicle is driven 40 or more times.

n If your vehicle does not pass the I/M test

Contact your Toyota dealer to prepare the vehicle for re-testing.

365

4-3. Do-it-yourself maintenance Do-it-yourself service precautions

If you perform maintenance yourself, be sure to follow the correct procedures as given in these sections.

Items

Parts and tools

Battery condition

(→P. 384)

Brake fluid level

(→P. 380)

Engine coolant level

(→P. 379)

Engine oil level

(→P. 374)

Fuses

(→P. 408)

• Warm water • Baking soda • Grease • Conventional wrench (for terminal clamp bolts) • FMVSS No.116 DOT 3 or SAE J1703 brake fluid • Rag or paper towel • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology. U.S.A.: “Toyota Super Long Life Coolant” is pre-mixed with 50% coolant and 50% deionized water. Canada: “Toyota Super Long Life Coolant” is pre-mixed with 55% coolant and 45% deionized water. • Toyota Genuine Motor Oil or equivalent • Rag or paper towel • Funnel (used only for adding oil) • Fuse with same amperage rating as original

366

4-3. Do-it-yourself maintenance

Items

Parts and tools

Light bulbs

(→P. 418)

Power steering fluid level

(→P. 382)

Radiator and condenser

(→P. 380)

Tire inflation pressure (→P. 396)

Washer fluid

(→P. 386)

• Bulb with same number and watt- age rating as original • Phillips-head screwdriver • Conventional wrench • Automatic transmission fluid DEXRON® II or III • Rag or paper towel

⎯

• Tire pressure gauge • Compressed air source • Water • Washer fluid containing antifreeze (for winter use)

367

4-3. Do-it-yourself maintenance

CAUTION

The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury observe the following precautions. n When working on the engine compartment

l Keep hands, clothing, and tools away from the moving fan and engine

drive belt.

l Be careful not to touch the engine, radiator, exhaust manifold, etc. right

after driving as they may be hot. Oil and other fluids may also be hot.

l Do not leave anything that may burn easily, such as paper or rags, in the

engine compartment.

l Do not smoke, cause sparks or expose an open flame to fuel or the bat-

tery. Fuel and battery fumes are flammable.

l Be extremely cautious when working on the battery. It contains poisonous

and corrosive sulfuric acid.

l Take care because brake fluid can harm your hands or eyes and damage

painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately. If you still experience discomfort, see a doctor.

n When working near the cooling fan or radiator grille

Be sure the engine switch is off. With the engine switch on, the cooling fan may automatically start to run if the air conditioning is on and/or the coolant temperature is high.

n Safety glasses

Wear safety glasses to prevent flying or falling material, fluid spray, etc. from getting in the eyes.

368

4-3. Do-it-yourself maintenance

NOTICE

n If you remove the air cleaner

Driving with the air cleaner removed may cause excessive engine wear due to dirt in the air. Also a backfire could cause a fire in the engine compart- ment.

n If the fluid level is low or high

It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, it may indicate a serious problem.

369

4-3. Do-it-yourself maintenance Hood

Release the lock from the inside of the vehicle to open the hood.

Pull the hood release lever. The hood will pop up slightly.

Pull up the hood catch lever and lift the hood.

370

4-3. Do-it-yourself maintenance

Hold the hood open by insert- ing the supporting rod into the slot.

CAUTION

n Pre-driving check

Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.

n After installing the support rod into the slot

Make sure the rod supports the hood securely from falling down on to your head or body.

NOTICE

n When closing the hood

Be sure to return the support rod to its clip before closing the hood. Closing the hood with the support rod up could cause the hood to bend.

371

4-3. Do-it-yourself maintenance Engine compartment

2.7 L 4-cylinder (2TR-FE) engine

Washer fluid tank (→P. 386) Radiator cap Engine coolant reservoir

(→P. 379)

Engine oil filler cap

(→P. 375) Power steering fluid reservoir (→P. 382)

Engine oil level dipstick

(→P. 374)

Brake fluid reservoir

Fuse box Battery Condenser Radiator

(→P. 380) (→P. 408) (→P. 384) (→P. 380) (→P. 380)

372

4-3. Do-it-yourself maintenance

4.0 L V6 (1GR-FE) engine

Washer fluid tank (→P. 386) Power steering fluid reservoir (→P. 382)

Radiator cap Engine oil level dipstick

(→P. 374)

Engine coolant reservoir

(→P. 379)

Engine oil filler cap

(→P. 375)

Brake fluid reservoir

Fuse box Battery Condenser Radiator

(→P. 380) (→P. 408) (→P. 384) (→P. 380) (→P. 380)

373

4-3. Do-it-yourself maintenance

Engine oilEngine oil

With the engine at operating temperature and turned off, check the oil level on the dipstick. n Checking the engine oil

Park the vehicle on level ground. After turning off the engine, wait more than 5 minutes for the oil to drain back into the bot- tom of the engine. Hold a rag under the end and pull the dipstick out.

2.7 L 4-cylinder (2TR-FE) engine

4.0 L V6 (1GR-FE) engine

Wipe the dipstick clean. Reinsert the dipstick fully. Holding a rag under the end, pull the dipstick out and check the oil level. Wipe the dipstick and reinsert it fully.

374

4-3. Do-it-yourself maintenance

2.7 L 4-cylinder (2TR-FE) engine

Low Full

Low Full

4.0 L V6 (1GR-FE) engine

n Adding engine oil

2.7 L 4-cylinder (2TR-FE) engine

If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine.

375

4-3. Do-it-yourself maintenance

4.0 L V6 (1GR-FE) engine

Make sure to check the oil type and prepare the items needed before adding oil.

Engine oil selection →P. 492
Items

Clean funnel

Remove the oil filler cap, turning it counterclockwise. Add engine oil slowly. Checking the dipstick. Reinstall the filler cap, turning it clockwise.

The approximate quantity of oil needed to raise the level between low and full on the dipstick is indicated as follows:

2.7 L 4-cylinder (2TR-FE) engine 1.4 qt. (1.3 L, 1.1 lmp. qt.) 4.0 L V6 (1GR-FE) engine 1.6 qt. (1.5 L, 1.3 lmp. qt.)

376

4-3. Do-it-yourself maintenance

n Engine oil consumption

l The amount of engine oil consumed depends on the oil viscosity, the

quality of the oil and the way the vehicle is driven.

l More oil is consumed under driving conditions such as high speeds and

frequent acceleration and deceleration.

l A new engine consumes more oil. l When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accu- rately.

l Oil consumption: Max. 1.1 qt./600 miles, 0.9 lmp.qt./600 miles (1.0 L per

1000 km) If you consume more than 1.1 qt. (1.0 L, 0.9 lmp.qt.) every 600 miles (1000 km), contact your Toyota dealer.

n After changing the engine oil (U.S.A. only)

The oil change system should be reset. Perform the following procedures:

Turn the engine switch off with the odometer reading shown. (→P. 157) Turn the engine switch to the ON position while holding down the trip meter reset button. Continue to press and hold the button until the odometer displays 000000.

If the system fails to reset, the light will continue flashing.

377

4-3. Do-it-yourself maintenance

CAUTION

n Used engine oil

l Used engine oil contains potentially harmful contaminants which may cause skin disorders such as inflammation or skin cancer, so care should be taken to avoid prolonged and repeated contact. To remove used engine oil from your skin, wash thoroughly with soap and water.

l Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal.

l Do not leave used engine oil within the reach of children.

NOTICE

n To prevent serious engine damage Check the oil level on regular basis.

n When replacing the engine oil

l Be careful not to spill engine oil on the vehicle components. l Avoid overfilling, as the engine could be damaged. l Check the oil level on the dipstick every time you refill the vehicle. l Be sure the engine oil filler cap is properly tightened.

378

4-3. Do-it-yourself maintenance

Engine coolant

The coolant level is satisfactory if it is between the FULL and LOW lines on the reservoir when the engine is cold.

Reservoir cap FULL LOW If the level is on or below the LOW line, add coolant up to the FULL line.

n If the coolant level drops within a short time after replenishing

Visually check the radiator, hoses, reservoir cap, radiator cap, drain cock and water pump. If you cannot find a leak, have your Toyota dealer pressure test the cap and check for leaks in the cooling system.

n Coolant selection

Only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology. U.S.A.:“Toyota Super Long Life Coolant” is a mixture of 50% coolant and

50% deionized water. (Enabled: -31°F [-35°C])

Canada:“Toyota Super Long Life Coolant” is a mixture of 55% coolant and

45% deionized water. (Enabled: -44°F [-42°C])

For more details about engine coolant, contact your Toyota dealer.

CAUTION

n When the engine is hot

Do not remove the radiator cap. The cooling system may be under pressure and may spray hot coolant if the cap is removed, causing burns or other injuries.

379

4-3. Do-it-yourself maintenance

NOTICE

n When adding engine coolant

Coolant is neither plain water nor straight antifreeze. The correct mixture of water and antifreeze must be used to provide proper lubrication, corrosion protection and cooling. Be sure to read the antifreeze or coolant label.

n If you spill coolant

Be sure to wash it off with water to prevent damage to parts or paint.

Radiator and condenser

Check the radiator and condenser and clear any foreign objects. If either of the above parts are extremely dirty or you are not sure of their condition, have your vehicle checked by your Toyota dealer.

CAUTION

n When the engine is hot

Do not touch the radiator or condenser as they may be hot and may cause burns.

Brake fluid

n Checking fluid level

Type A

380

The brake fluid level should be between the MAX and MIN lines on the reservoir.

MAX MIN

4-3. Do-it-yourself maintenance

Type B

MAX MIN

n Adding fluid Make sure to check the fluid type and prepare the necessary items.

Fluid type Items

FMVSS No.116 DOT 3 or SAE J1703 brake fluid Rag or paper towel

Type B only

Turn the engine switch off. Depress the brake pedal 20 times or more. Remove the reservoir cap. Add newly opened brake fluid up to the MAX line.

n Brake fluid can absorb moisture from the air

Excess moisture in the fluid can cause a dangerous loss of braking effi- ciency. Use only newly opened brake fluid.

381

4-3. Do-it-yourself maintenance

CAUTION

n When filling the reservoir

Take care because brake fluid can harm your hands or eyes and damage painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately. If you still experience discomfort, see a doctor.

NOTICE

n If the fluid level is low or high

It is normal for the brake fluid level to go down slightly as the brake pads wear or when the fluid level in the accumulator is high. If the reservoir needs frequent refilling, it may indicate a serious problem.

n If you spill fluid

Be sure to wash it off with water to prevent damage to parts or paint.

Power steering fluid

n Fluid level The fluid level should be within the appropriate range.

2.7 L 4-cylinder (2TR-FE) engine

Full (when cold) Add fluid (when cold) Full (when hot) Add fluid (when hot)

382

4-3. Do-it-yourself maintenance

Hot:

Cold:

Vehicle has been driven around 50 mph (80 km/h) for 20
minutes, or slightly longer in frigid temperatures. (Fluid temperature, 104°F - 175°F [40°C - 80°C]) Engine has not been run for about 5 hours. (Room tem- perature, 32°F - 104°F [0°C - 40°C])

4.0 L V6 (1GR-FE) engine

Full (when cold) Add fluid (when cold) Full (when hot) Add fluid (when hot)

Hot:

Cold:

Vehicle has been driven around 50 mph (80 km/h) for 20
minutes, or slightly longer in frigid temperatures. (Fluid temperature, 140°F - 175°F [60°C - 80°C]) Engine has not been run for about 5 hours. (Room tem- perature, 50°F - 85°F [10°C - 30°C])

n Checking the fluid level Make sure to check the fluid type and prepare the necessary items.

Fluid type

Items

Automatic transmission fluid DEXRON® II or III Rag or paper towel

Clean all dirt off the reservoir. Remove the cap by turning it counterclockwise. Wipe the dipstick clean. Reinstall and remove the reservoir cap again. Check the fluid level.

383

4-3. Do-it-yourself maintenance

CAUTION

n Checking the fluid level

Take care, as the reservoir may be hot.

NOTICE

n When adding fluid

Avoid overfilling, or the power steering may be damaged.

n After replacing the reservoir cap

Check the steering box case, vane pump and hose connections for leaks or damage.

Battery

n Battery exterior

Make sure that the battery terminals are not corroded and that there are no loose connections, cracks, or loose clamps.

Terminals Hold-down clamp

384

4-3. Do-it-yourself maintenance

n Before recharging

When recharging, the battery produces hydrogen gas which is flammable and explosive. Therefore, before recharging:

If recharging with the battery installed on the vehicle, be sure to discon- nect the ground cable.

l Make sure the power switch on the charger is off when connecting and

disconnecting the charger cables to the battery.

CAUTION

n Chemicals in the battery

A battery contains poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near bat- tery: l Do not cause sparks by touching the battery terminals with tools. l Do not smoke or light a match near the battery. l Avoid contact with eyes, skin and clothes. l Never inhale or swallow electrolyte. l Wear protective safety glasses when working near the battery. l Keep children away from the battery.

n Where to safety charge the battery

Always charge the battery in an open area. Do not charge the battery in a garage or closed room where there is not sufficient ventilation.