2005 Toyota Tacoma Owners Manual

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

89

05 02.25

LS13008

LS13025

(A) INFANT SEAT INSTALLATION An infant seat must be used in rear- facing position only.

Bench seat

LS13005

Separate seats

CAUTION

Never install a rear- facing child re- straint system on the right front seat with the passenger airbag manual on- off switch in the “ON” or “AUTO” position. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the rear- facing child restraint system is installed on the front passenger seat.

90

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

LS13027a

Bench seat

LS13006a

Separate seats

When you install a rear- facing child re- straint system which belongs to a pas- senger risk group on the right front seat, turn the passenger airbag manual on- off switch counterclockwise to the “OFF” position and remove the key. (For details, see “SRS driver airbag and front passenger airbag” on page 55 in this Section.) The indicator system is off.

light comes on when the

CAUTION

If you must install a rear- facing child restraint system on the right front seat, make sure that the front passen- ger airbag manual on- off switch is in the “OFF” position with the key re- moved and that the indicator light is on.

LS13007

CAUTION

the

lock mechanism of

(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.

(cid:1) If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

91

05 02.25

LS13009

1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

LS13010

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

the

To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.

92

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

LS13011

LS13012

LS13013

3. While pressing the infant seat

firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the infant seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

93

05 02.25

LS13014

LS13026

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat must be used in for- ward- facing or rear- facing position de- pending on the age and size of the child. When the manufacturer’s instruction about the ap- plicable age and size of the child as well as directions the child restraint system.

installing,

installing

follow

for

Bench seat

LS13015

Separate seats

CAUTION

Rear- facing child restraint system: Never install a rear- facing child re- straint system on the right front seat with the passenger airbag manual on- off switch in the “ON” or “AUTO” position. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious injury to the child if the is installed on the front passenger seat.

rear- facing

system

child

94

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

LS13027a

Bench seat

LS13006a

Separate seats

When you install a rear- facing child re- straint system which belongs to a pas- senger risk group on the right front seat, turn the passenger airbag manual on- off switch counterclockwise to the “OFF” position and remove the key. (For details, see “SRS driver airbag and front passenger airbag” on page 55 in this Section.) The indicator system is off.

light comes on when the

CAUTION

If you must install a rear- facing child restraint system on the right front seat, make sure that the passenger airbag manual on- off switch is in the “OFF” position with the key removed and that the indicator light is on.

CAUTION

child

forward- facing

Forward- facing child restraint system: restraint system which belongs to a passenger risk group should never be installed on the right front passenger seat with the passenger airbag manual on- off switch “AUTO” position, because force of the deploying airbag could cause death or serious in forward seating position. (For details, see “SRS driver airbag and front passenger airbag” on page 55 in this Section.)

the child

“ON” or

injury

the

the

to

in

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

95

05 02.25

LS13016

LS13017

CAUTION

the

lock mechanism of

(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.

1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided insert the

by tab

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

(cid:1) If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.

96

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

LS13018

LS13019

LS13020

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

97

05 02.25

LS13021

LS13022

4. To remove the convertible seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward- facing position only.

CAUTION

A forward- facing child restraint sys- tem which belongs to a passenger risk group should never be installed on the right front seat with the pas- senger airbag manual on- off switch in the “ON” or “AUTO” position, be- cause the force of the deploying air- bag could cause death or serious in- jury to the child in forward seating position. (For details, see “SRS driver airbag and front passenger airbag” on page 55 in this Section.)

98

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

LS13023

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt.

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips. See “Seat belts” on page 43 in this Section for details.

CAUTION

(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.

(cid:1) If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

could

(cid:1) Both high- positioned lap belts and cause loose- fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.

injuries due

(cid:1) For child’s safety, do not place the

shoulder belt under child’s arm.

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

99

05 02.25

—Installation with seat belt (double cab models)

LS13024

LS13028

LS13029

2. To remove the booster seat, press the the

buckle release button and allow belt to retract.

(A) INFANT SEAT INSTALLATION An infant seat must be used in rear- facing position only.

CAUTION

classification

(cid:1) Never install a rear- facing child re- straint system on the front passen- ger seat even if the front passenger occupant indicator light indicates “OFF”. In the event of an accident, the impact of the rapid inflation of the front passen- ger airbag could cause death or se- rious injury to the child if the rear- facing child is front passenger installed on seat.

restraint system the

100

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

LS13030

LS13031

the

lock mechanism of

(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.

1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

(cid:1) If the driver’s seat position does not allow sufficient space for safe the child installation, install re- the rear right straint system on seat. system installed on the rear seat should not contact the front seatbacks.

restraint

Child

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

101

05 02.25

LS13032

LS13033

LS13034

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

the

To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing the infant seat

firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

102

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

LS13035

LS13036

4. To remove the infant seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat must be used in for- ward- facing or rear- facing position de- pending on the age and size of the the child. When manufacturer’s the applicable age and size of the child as well as directions the child restraint system.

installing, follow instructions about

installing

for

Install the child restraint system on the front passenger seat only when it is un- avoidable. Your vehicle is equipped with a front passenger occupant classification system. In order to activate the occupant classification system correctly, install the forward- facing child restraint system on the front passenger seat in the following order: 1. Turn the ignition key to the “ON” posi-

tion.

2. Move the front passenger seat to the

rearward position.

3. Put the child restraint system on the front passenger seat without putting your weight on front passenger seat.

the

4. Insert the seat belt tab into the seat

belt buckle.

5. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended. To hold the seat securely, make sure the belt is in the lock mode before letting the belt retract.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

103

05 02.25

6. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

7. Put a child on the child restraint sys- tem and secure the child, complying with the instructions provided by the child restraint system manufacturer.

indicator

indicates

The front passenger occupant classifica- tion indicator light should indicate “OFF” when the ignition key is in the “ON” posi- tion and the child is in the child restraint system after following these procedures. The “OFF” the SRS front passenger airbag and side airbag on the passenger side will not deploy. if the indicator light indicates “ON”, remove the child restraint system and reinstall it with the ignition key in the “ACC” or “LOCK” position. If the indicator light still indicates “ON” when the ignition key is turned to the “ON” position, then the SRS front pas- senger airbag and side airbag on the pas- senger side may deploy in an accident. Do not drive the vehicle in this condition. Remove the child restraint system and contact your Toyota dealer.

CAUTION

the

(cid:1) Never install a rear- facing child re- straint system on the front passen- ger seat. A forward- facing child re- straint system should only be installed on front passenger seat when unavoidable. If you must install the child restraint system on the front passenger seat, put the seat in its most rearward position, and install the forward- facing child restraint system in the proper or- der. Otherwise, the front passenger occupant classification system can not detect the presence of the child restraint system and the front pas- senger airbag and side airbag on the front passenger seat could deploy.

104

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

LS13037

LS13038

Move seat fully back

the

(cid:1) A forward- facing child restraint sys- tem should be allowed to be installed on front passenger seat only when it is unavoidable. Always move the seat as far back as possible even if the front pas- senger occupant classification indi- cator light indicates “OFF”, because the front passenger airbag could in- flate with considerable speed and force. Otherwise, the child may be killed or seriously injured.

CAUTION

classification

(cid:1) Never install a rear- facing child re- straint system on the front passen- ger seat even if the front passenger occupant indicator light indicates “OFF”. In the event of an accident, the impact of the rapid inflation of the front passen- ger airbag could cause death or se- rious injury to the child if the rear- facing child is front passenger installed on seat.

restraint system the

(cid:1) On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbag and curtain shield airbag in- flate, and the impact could cause death or serious injury to the child.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

105

05 02.25

LS13039

LS13040

the

lock mechanism of

(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.

1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided insert the

by tab

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

(cid:1) If the driver’s seat position does not allow sufficient space for safe the child installation, install re- the rear right straint system on seat. system installed on the rear seat should not contact the front seatbacks.

restraint

Child

106

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

LS13041

LS13042

LS13043

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

107

05 02.25

LS13044

LS13045

LS13046

4. To remove the convertible seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward- facing position only.

Move seat fully back

CAUTION

the

(cid:1) A forward- facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible, because the front pas- senger airbag could inflate with considerable force. and speed Otherwise, the child may be killed or seriously injured.

108

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

(cid:1) On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbag and curtain shield airbag in- flate, and the impact could cause death or serious injury to the child.

LS13047

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt.

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips. See “Seat belts” in this Section for details.

CAUTION

(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.

could

(cid:1) Both high- positioned lap belts and cause loose- fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.

injuries due

(cid:1) For child’s safety, do not place the

shoulder belt under child’s arm.

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

109

05 02.25

(cid:1) If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

LS13048

LS13050a

—Using a top strap (regular cab models)

2. To remove the booster seat, press the the

buckle release button and allow belt to retract.

Follow the procedure below for a child restraint system that requires the use of a top strap.

110

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

Symbol mark

Routing device

LS13052b

Use the routing device and the anchor bracket on the back panel to attach the top strap. Anchor brackets are installed for (each) passenger seating position. This symbol indicates the location of the anchor bracket.

LS13063

Anchor brackets

Bench seat

Symbol mark

Routing device

LS13053bAnchor

bracket

Separate seats

TO USE THE ANCHOR BRACKET: 1. Remove

the passenger head

re-

straint.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

111

05 02.25

Symbol mark

LS13181

LS13064b

LS13065b

2. Lightly push down on the top sur- face of the routing device cover with the symbol mark shown in the il- lustration, then pull it forward to re- move.

the

through

top strap

3. Pull the seatback release lever and swing the seatback forward slightly. Route the routing device as shown in the il- lustration. Latch bracket. Return the seatback to upright posi- tion.

the hook onto

the anchor

4. Fix the child restraint system with the seat belt and tighten the top strap. Replace straint.

the passenger head

re-

Store the removed cover in a safe place such as the glove box. Be sure to replace the cover when the anchor bracket is not in use. For instructions on installing the child re- straint system, see “Child restraint” on page 86 in this Section.

112

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

CAUTION

(cid:1) When returning the seatback to its the original position, make sure seatback locked by pushing forward and rearward on the top of the seatback.

is securely

(cid:1) Make sure the top strap is securely latched, and check that the child restraint system is secure by push- ing and pulling it in different direc- tions. Follow all the installation in- structions provided by its manufac- turer.

—Using a top strap (access cab models)

LS13069

Front position

Follow the procedure below for a child restraint system that requires the use of a top strap.

LS13070a

Rear position

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

113

05 02.25

LS13071

Symbol mark

Routing device or upper anchor bracket

Lower anchor bracket

LS13072

Symbol mark

LS13073

the routing device and the anchor

Use bracket to attach the top strap. Upper anchor bracket is installed for front passenger’s seating position, lower anchor bracket is installed for right- rear seating position. This symbol user ready anchor bracket.

locations of

indicates

the

TO USE THE ANCHOR BRACKET: Front position— 1. Remove

the passenger head

re-

straint. Lightly push down on the top sur- face of the anchor bracket cover with the symbol mark shown in the illustration, then pull it forward to remove.

2. Fix the child restraint system with

the seat belt. Latch the anchor bracket on the back panel and tight- en the top strap.

the hook onto

For instructions on installing the child re- straint system, see “Child restraint” on page 86 in this Section.

114

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

Symbol mark

LS13074

LS13075

3. Replace the head restraint. Store the removed cover in a safe place such as the glove box. Be sure to replace the cover when the anchor bracket is not in use.

Rear position— 1. Upper anchor bracket:

Lightly push down on the top sur- face of the upper anchor bracket cover with the symbol mark shown in the illustration, then pull it for- ward to remove. Lower anchor bracket: Pull up the lower anchor bracket.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

115

05 02.25

—Using a top strap (double cab models)

Routing device

LS13076a

LS13077a

LS13051

2. Fix the child restraint system with

the seat belt. Route the routing device as shown in the il- lustration.

top strap

through

the

For instructions on installing the child re- straint system, see “Child restraint” on page 86 in this Section.

CAUTION

Make sure twisted.

the

top strap

is not

3. Latch the hook onto the rear lower anchor bracket and tighten the top strap.

Follow the procedure below for a child restraint system that requires the use of a top strap.

Store the removed covers in a safe place such as the glove box. Be sure to replace the covers when the anchor bracket is not in use.

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

116

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

Symbol mark

LS13054a

LS13066

LS13067

Anchor brackets

Use the anchor bracket on the back panel to attach the top strap. Anchor brackets are rear seating position. This symbol indicates the location of the anchor bracket.

for each

installed

TO USE THE ANCHOR BRACKET: 1. Remove the head restraint.

2. Pull the seatback release strap and swing the seatback forward slightly, then latch the hook onto the anchor bracket. Return the seatback to its original position.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

117

05 02.25

CAUTION

is securely

(cid:1) When returning the seatback to its the original position, make sure seatback locked by pushing forward and rearward on the top of the seatback. Failure to do so will prevent the seat belt from operating properly.

(cid:1) Make sure the top strap is securely latched, and check that the child restraint system is secure by push- ing and pulling it in different direc- tions. Follow all the installation in- structions provided by its manufac- turer.

LS13068

3. Fix the child restraint system with the seat belt and tighten the top strap. Replace the head restraint.

For instructions on installing the child re- straint system, see “Child restraint” on page 86 in this Section.

—Installation with child restraint lower anchorages (regular cab models)

LS13078

Separate seats

LS13079

118

Bench seat

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

specifications

Lower anchorages for the child restraint systems complying with the FMVSS225
or CMVSS210.2 are installed in the right passenger’s seat- ing position. The anchorages are installed in the gap between the seat cushion and seatback of the right side of the seat as shown in the illustration. Child restraint systems complying with the FMVSS213 or CMVSS213 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

1st lock position

10th lock position

LS13160a

SYSTEM

RESTRAINT

CHILD INSTALLATION 1. Separate seats only—Fold down the seatback and back to the 1st lock position (most upright position) until it locks into place. Adjust the seat- back to the 10th lock position.

LS13080

Make sure the seatback is locked secure- ly.

Canada only

Type A

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

119

05 02.25

2. Widen

the gap between

the seat cushion and seatback slightly and confirm the position of the lower an- chorages near the seatback.

the button on

3. Type A—Latch the hooks of

lower the anchorages and

straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.

LS13081

For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 110 in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.

it should be anchored. (For

CAUTION

(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

(cid:1) After securing

the child restraint system, never slide or recline the seat.

Canada only

Type B

120

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

—Installation with child restraint lower anchorages (access cab models)

LS13078

Front seat

LS13099

Rear seat

specifications

Lower anchorages for the child restraint systems complying with the FMVSS225
or CMVSS210.2 are installed in the seat. Front seat without seatback table— The anchorages are installed in the gap between the seat cushion and seatback of the seat as shown in the illustration. Front seat with seatback table— The anchorages are installed in the seat cushion of the seat. Rear seat— The anchorages are located at the base of the seatback as shown in the illustra- tion. Child restraint systems complying with the FMVSS213 or CMVSS213 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

1st lock position

10th lock position

LS13160a

SYSTEM

RESTRAINT

CHILD INSTALLATION 1. Front seat—Fold down the front seat seatback and back to the 1st lock position (most upright position) until it locks into place. Adjust the seat- back to the 10th lock position.

Make sure the seatback is locked secure- ly.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

121

05 02.25

LS13082

LS13083

LS13186

Canada only

Canada only

Canada only

Front seat without seatback table (type A)

Front seat without seatback table (type B)

Front seat with seatback table (type A)

122

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

LS13187

LS13100

LS13101

Canada only

Canada only

Canada only

Front seat with seatback table (type B)

Rear seat (type A)

Rear seat (type B)

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

123

05 02.25

the gap between

Front seat— 2. Front seat without seatback table— the seat Widen cushion and seatback slightly and confirm the position of the lower an- chorages near the seatback. Front seat with seatback table—Wid- en the seat cushion slightly and confirm the position of the lower anchorages near the but- ton on the seat cushion.

the button on

the slits of

3. Type A—Latch the hooks of

lower the anchorages and

straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.

the hooks of

Rear seat— Type A—Latch lower straps onto the anchorages and tighten the lower straps. Type B—Latch the buckles onto the an- chorages. For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system.

the

lock mechanism of

(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.

it should be anchored. (For

If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 113 in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.

CAUTION

(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

(cid:1) After securing

the child restraint system, never slide or recline the seat.

124

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

—Installation with child restraint lower anchorages (double cab models)

LS13084

specifications

Lower anchorages for the child restraint systems complying with the FMVSS225
or CMVSS210.2 are installed in the rear seat. The anchorages are installed in the gap between the seat cushion and seatback of both outside rear seats as shown in the illustration. Child restraint systems complying with the FMVSS213 or CMVSS213 specification can be fixed with these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

LS13085

LS13086

Canada only

Canada only

Type A

Type B

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

125

05 02.25

RESTRAINT

SYSTEM

CAUTION

CHILD INSTALLATION 1. Widen

the gap between

the seat cushion and seatback slightly and confirm the position of the lower an- chorages near the seatback.

the button on

2. Type A—Latch the hooks of

lower the anchorages and

straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.

For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 116 in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.

it should be anchored. (For

(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

(cid:1) After securing

the child restraint

system, never recline the seat.

the

lock mechanism of

(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.

126

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

SECTION 1- 4

OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt and telescopic steering wheel Outside rear view mirrors Anti- glare inside rear view mirror Auto anti- glare inside rear view mirror Sun visors Vanity mirrors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

128
128
130
131
132
132

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

127

05 02.25

Tilt and telescopic steering wheel

Outside rear view mirrors—

CAUTION

(cid:1) Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.

(cid:1) After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.

LS14001a

To adjust the steering wheel position, push down the lock release lever. Then tilt the steering wheel to the desired angle, push or pull it to the desired steering column length and pull up the lock release lever.

LS14002

Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side because it is a convex mirror. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.

128

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

—Power rear view mirror control

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

LS14003

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de-icer to free the mirror.

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Push (right).

the switch to “L” (left) or “R”

2. Control switch—To move the mirror

Push the switch in the desired direc- tion.

Mirrors can be adjusted when the key is in the “ACC” or “ON” position.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

129

05 02.25

—Folding rear view mirrors

Anti- glare inside rear view mirror

LS14004

LS14005

CAUTION

Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.

The rear view mirrors can be folded backward for parking in compact areas. To fold the rear view mirror, push back- ward.

CAUTION

Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

130

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

Auto anti- glare inside rear view mirror

LS14006

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. This mirror is equipped with auto anti- glare function. The function is designed to reduce glare from the headlights of the vehicle behind you during night driving. When inserted and turned on, the inside rear view mirror al- ways turns on in the automatic function mode. The indicator illuminates to show you that the function is on.

ignition key

the

is

to reduce

In automatic function mode, if the mirror detects light from the headlights of the the mirror surface vehicle behind you, darkens slightly the reflected light. To turn off the automatic function, push the “OFF” switch. To turn on the automatic function again, push the “AUTO” switch. Adjust it before driving so that the rear view is in the best condition. When the inside air temperature is low, it may take a little longer for the mirror to darken the detection of headlights.

in response

to

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

LS14007

To ensure correct functioning of anti- glare mirror sensors located on both sides of the mirror, do not touch or cover the sensors with your finger or a piece of cloth, etc.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

131

05 02.25

Sun visors

Vanity mirrors

LS14009

To block out glare, move the sun visor. To block out glare from the front—Swing down the sun visor (position 1). To block out glare from the side—Swing down the sun visor, remove it from the hook and swing it to the lateral side (posi- tion 2). Type B— If glare comes from obliquely behind you, extend the plate at the end of the visor (position 3).

LS14010

Type A

CAUTION

Type A

Type B— Do not extend the plate at the end of the sun visor when the visor is in the position 1. It can cover the anti- glare inside rear view mirror and obstruct the rear view.

LS14008

LS14011

Type B

132

Type B (passenger’s side only)

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

Type A— To use the vanity mirrors, swing down the sun visor and slide the cover. Type B— To use the vanity mirror, swing down the sun visor.

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

133

05 02.25

134

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

05 02.25

SECTION 1- 5

OPERATION OF INSTRUMENTS AND CONTROLS Lights and Wipers Headlights and turn signals Emergency flashers Instrument panel light control Front fog lights Interior light Personal lights Windshield wipers and washer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

136
138
138
139
139
140
140

2005 TACOMA from Mar. ’05 Prod. (OM35862U)

135

05 02.25

Headlights and turn signals

LS15001b

For the U.S.A.

LS15002b

For Canada

136

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

the

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob.