2012 Toyota Sienna Owners Manual

■ TWR (Trailer Weight Rating): 3500 lb. (1588 kg)

TWR means the maximum gross trailer weight (trailer weight plus its cargo weight) that your vehicle is able to tow.

■ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 683)

CAUTION

■Overloading the vehicle

Observe the total load capacity when you load the vehicle. (→P. 784) Otherwise, it may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

351

SIENNA_U (OM45477U)

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations

● Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

● Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

● Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. ■ Before driving the vehicle

Perform the following according to the driving conditions: ● Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. ● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

● Remove any ice that has accumulated on the vehicle chassis. ● Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

352

SIENNA_U (OM45477U)

2-5. Driving information

■ When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

■ When parking the vehicle

Park the vehicle and move the shift lever to P without setting the parking brake. The parking brake may freeze up, preventing it from being released. If necessary, block the wheels to prevent inadvertent sliding or creeping.

Selecting tire chains

Use the tire chains of correct size and type.

Use SAE Class “S” type radial tire chains, with the exception of radial cable chains or V-bar type chains.

Regulations on the use of tire chains

Regulations regarding the use of tire chains vary depending on loca- tion and type of road. Always check local regulations before installing chains.

353

SIENNA_U (OM45477U)

2-5. Driving information

■Tire chain installation

Observe the following precautions when installing and removing chains. ●Install and remove tire chains in a safe location. ●Install tire chains on the front tires only. Do not install tire chains on the

rear tires.

●Install tire chains on front tires as tightly as possible. Retighten chains

after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

●Install tire chains following the instructions provided with the tire chains.

CAUTION

■Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the size specified. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

●Use snow tires on all, not just some wheels.

354

SIENNA_U (OM45477U)

2

2-5. Driving information

CAUTION

■Driving with tire chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden turns and braking, as use of chains may adversely affect

vehicle handling.

●Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

NOTICE

■Repairing or replacing snow tires

Request repairs of or replacement of snow tires from Toyota dealers or legit- imate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

■Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

355

SIENNA_U (OM45477U)

2-5. Driving information Trailer towing (with towing package)

Your vehicle is designed primarily as a passenger-and-load-carrying vehicle. Towing a trailer can have an adverse impact on handling, performance, braking, durability, and fuel consumption. For your safety and the safety of others, you must not overload your vehicle or trailer. You must also ensure that you are using appropriate tow- ing equipment, that the towing equipment has been installed cor- rectly and used properly, and that you employ the requisite driving habits. Vehicle-trailer stability and braking performance are affected by trailer stability, brake performance and setting, trailer brakes, the hitch and hitch systems (if equipped). To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating condi- tions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional requirements such as a towing kit, etc.

356

SIENNA_U (OM45477U)

2

2-5. Driving information

Towing related terms

■ GCWR (Gross Combination Weight Rating)

The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the cargo in the trailer).

■ GVWR (Gross Vehicle Weight Rating)

The maximum allowable gross vehicle weight. The gross vehicle weight is the total weight of the vehicle. When towing a trailer, it is the sum of the vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the tongue weight.

357

SIENNA_U (OM45477U)

2-5. Driving information

■ GAWR (Gross Axle Weight Rating)

Front GAWR

Rear GAWR

The maximum allowable gross axle weight. The gross axle weight is the load placed on each axle (front and rear).

■ TWR (Trailer Weight Rating)

(With brakes)

The maximum allowable gross trailer weight. The gross trailer weight is the sum of the trailer weight and the weight of the cargo in the trailer. is calculated assuming TWR base vehicle with one driver, one front passenger, towing package (if available), hitch and hitch sys- tems (if required).

Additional optional equipment, passengers and cargo in the vehi- cle will reduce the trailer weight rating so as not to exceed GCWR, GVWR and GAWR. If the gross trailer weight exceeds 3000 lb. (1360 kg), it is recom- mended to use a trailer with 2 or more axles.

358

SIENNA_U (OM45477U)

2-5. Driving information

■ Unbraked TWR (Unbraked Trailer Weight Rating)

(Without brakes)

The trailer weight rating for tow- ing a trailer without a trailer ser- vice brake system.

■ Tongue Weight

The load placed on the trailer hitch ball. (→P. 362)

359

SIENNA_U (OM45477U)

2-5. Driving information

Weight limits

● The gross trailer weight must never exceed 3500 lb. (1588 kg). ● The gross combination weight must never exceed the GCWR

described below. 2WD models: 8900 lb. (4037 kg) AWD models: 8990 lb. (4078 kg)

● The gross vehicle weight must never exceed the GVWR indi- cated on the Certification Label.

● The gross axle weight on each axle must never exceed the GAWR indicated on the Certi- fication Label.

● If the gross trailer weight is over the unbraked TWR, trailer service

brakes are required.

● If the gross trailer weight is over 2000 lbs. (907 kg), a sway control

device with sufficient capacity is required.

360

SIENNA_U (OM45477U)

2

2-5. Driving information

GCWR, TWR and Unbraked TWR

Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits. ■ GCWR∗

2WD models: 8900 lb. (4037 kg) AWD models: 8990 lb. (4078 kg)

■ TWR∗

3500 lb. (1588 kg) ■ Unbraked TWR∗ 1650 lb. (750 kg)

∗: These models meet the tow-vehicle trailering requirement of SAE Interna-

tional per SAE J2807.

361

SIENNA_U (OM45477U)

2-5. Driving information

Trailer Tongue Weight

● A recommended tongue weight varies in accordance with the types

of trailers or towing as described below.

● To ensure the recommended values shown below, the trailer must

be loaded by referring to the following instructions. • Tongue Weight

The gross trailer weight should be distributed so that the tongue weight is 9 to 11 %. (Tongue weight / Gross trailer weight × 100 = 9 to 11 %)

Gross trailer weight Tongue weight

If using a weight distributing hitch when towing, return the front axle to the same weight as before the trailer connection. If front axle weight cannot be measured directly, measure the front fender height above the front axle before connection. Adjust weight distributing hitch torque until front fender is returned to the same height as before connection. The gross trailer weight, gross axle weight and tongue weight can be measured with platform scales found at a highway weighing sta- tion, building supply company, trucking company, junk yard, etc.

362

SIENNA_U (OM45477U)

2-5. Driving information

Hitch

Trailer hitch assemblies have different weight capacities. Toyota rec- ommends the use of Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight require-

ment of your vehicle.

● Follow the directions supplied by the hitch manufacturer. ● Lubricate the hitch ball with a light coating of grease. ● Remove the trailer hitch whenever you are not towing a trailer. After removing the hitch, seal any mounting hole in the vehicle body to prevent entry of any substances into the vehicle.

363

SIENNA_U (OM45477U)

2-5. Driving information

Selecting trailer ball

Use the correct trailer ball for your application.

Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers are stamped with the required trailer ball size.

Trailer class

Typical trailer ball size

IV

2 5/16 in.

II and III

2 in.

1 7/8 in.

Shank length Protrudes beyond the bottom of the lock washer and nut at least 2
threads. Shank diameter Matches diameter size.

the ball mount hole

364

SIENNA_U (OM45477U)

Positions for towing hitch receiver

2-5. Driving information

Hitch receiver pin hole posi- tion: 37.3 in. (949.8 mm)

Connecting trailer lights

Please consult your dealer when installing trailer lights, as incorrect installation may cause damage to the vehicle’s lights. Please take care to comply with your state’s laws when installing trailer lights.

365

SIENNA_U (OM45477U)

2-5. Driving information

Trailer towing tips

Your vehicle will handle differently when towing a trailer. Help to avoid an accident, death or serious injury, keep the following in mind when towing: ● Speed limits for towing a trailer vary by state or province. Do not

exceed the posted towing speed limit.

● Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest. Instability of the towing vehicle-trailer combination (trailer sway) increases as speed increases. Exceeding speed limits may cause loss of con- trol.

● Before starting out, check the trailer lights, tires and the vehicle-

trailer connections. Recheck after driving a short distance.

● Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle-trailer combination.

366

SIENNA_U (OM45477U)

2-5. Driving information

● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to the right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

● As stopping distance is increased when towing a trailer, vehicle-to- vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

● Avoid sudden braking as you may skid, resulting in the trailer jack- knifing and a loss of vehicle control. This is especially true on wet or slippery surfaces.

● Avoid jerky starts or sudden acceleration. ● Avoid jerky steering and sharp turns, and slow down before mak-

ing a turn.

● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a wider than normal turning radius.

● Slow down before making a turn, in crosswinds, on wet or slippery

surfaces, etc. Increasing vehicle speed can destabilize the trailer.

367

SIENNA_U (OM45477U)

2-5. Driving information

● Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

● To maintain engine braking efficiency and charging system perfor- mance when using engine braking, do not put the transmission in D. Transmission shift range position must be in 4 in the S mode.

● Instability happens more frequently when descending steep or long downhill grades. Before descending, slow down and downshift. Do not make sudden downshifts while descending steep or long down- hill grades.

● Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

● Due to the added load of the trailer, your vehicle’s engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the Engine coolant temperature gauge overheating, immediately turn off the air conditioning (if in use), pull your vehicle off the road and stop in a safe spot. (→P. 775)

368

SIENNA_U (OM45477U)

2

2-5. Driving information

STEP 3

STEP 2

STEP 1

● Always place wheel blocks under both the vehicle’s and the trailer’s wheels when parking. Apply the parking brake firmly, and put the transmission in P. Avoid parking on a slope, but if unavoid- able, do so only after performing the following: Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle’s and trailer’s wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into P and turn off the engine. STEP 5
● When restarting after parking on a slope: STEP 1

With the transmission in P, start the engine. Be sure to keep the brake pedal pressed. Shift into a forward gear. If reversing, shift into R. Release the parking brake and brake pedal, and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

STEP 2

STEP 3

STEP 4

STEP 4

369

SIENNA_U (OM45477U)

2-5. Driving information

■Matching trailer ball height to trailer coupler height

No matter which class of tow hitch applies, for a safe trailer hookup, the trailer ball setup on must be proper height for the coupler on the trailer.

Coupler Trailer ball

■Before towing

Check that the following conditions are met: ●Ensure that your vehicle’s tires are properly inflated. (→P. 794) ●Trailer tires are inflated according to the trailer manufacturer’s recom-

mendation.

●All trailer lights work as required by law. ●All lights work each time you connect them. ●The trailer ball is set at the proper height for the coupler on the trailer. ●The vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue weight, overloading, worn suspension, or other possible causes.

●The trailer cargo is securely loaded. ●The rear view mirrors conform to all applicable federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes.

370

SIENNA_U (OM45477U)

2

2-5. Driving information

■Break-in schedule

If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km). After the vehicle has been driven for over 500 miles (800 km), you can start towing. However, for the next 500 miles (800 km), drive the vehicle at a speed of less than 50 mph (80 km/h) when towing a trailer, and avoid full throttle acceleration.

■Maintenance

●If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

●Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km) of trailer towing.

371

SIENNA_U (OM45477U)

2-5. Driving information

■If trailer sway occurs

One or more factors (crosswinds, passing vehicles, rough roads, etc.) can adversely affect handling of your vehicle and trailer, causing instability. ●If trailer swaying occurs:

• Firmly grip the steering wheel. Steer straight ahead.

Do not try to control trailer swaying by turning the steering wheel.

• Begin releasing the accelerator pedal immediately but very gradually to

reduce speed. Do not increase speed. Do not apply vehicle brakes.

If you make no extreme correction with the steering or brakes, your vehicle and trailer should stabilize. ●After the trailer swaying has stopped:

• Stop in a safe place. Get all occupants out of the vehicle. • Check the tires of the vehicle and the trailer. • Check the load in the trailer.

Make sure the load has not shifted. Make sure the tongue weight is appropriate, if possible.

• Check the load in the vehicle.

Make sure the vehicle is not overloaded after occupants get in.

If you cannot find any problems, the speed at which trailer swaying occurred is beyond the limit of your particular vehicle-trailer combination. Drive at a lower speed to prevent instability. Remember that swaying of the towing vehicle-trailer increases as speed increases.

372

SIENNA_U (OM45477U)

2-5. Driving information

CAUTION

■Trailer towing precautions

To tow a trailer safely, use extreme care and drive the vehicle in accordance with the trailer’s characteristics and operating conditions. Failure to do so could cause an accident resulting in death or serious injury. Vehicle stability and braking performance are affected by trailer stability, brake setting and performance, and the hitch. Your vehicle will handle differently when towing a trailer.

■To avoid accident or injury

●Do not exceed the TWR, unbraked TWR, GCWR, GVWR or GAWR. ●If the gross trailer weight is over 2000 lb. (907 kg), a sway control device

with sufficient capacity is required.

●Adjust the tongue weight within the appropriate range. Place heavier loads

as close to the trailer axle as possible.

●Do not exceed 65 mph (104 km/h), the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest. Slow down sufficiently before making a turn, in cross- winds, on wet or slippery surface, etc. to help avoid an accident. If you experience a vehicle-trailer instability from reducing a certain speed, slow down and make sure you keep your vehicle speed under the speed of which you experience the instability.

●Do not make jerky, abrupt or sharp turns. ●Do not apply the brakes suddenly as you may skid, resulting in jackknifing and loss of vehicle control. This is especially true on wet or slippery sur- faces.

●Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue weight capacities.

373

SIENNA_U (OM45477U)

2-5. Driving information

CAUTION

■To avoid accident or injury

●Do not use cruise control when towing. ●Slow down and downshift before descending steep or long downhill grades. Do not make sudden downshifts while descending steep or long downhill grades.

●Vehicle-trailer instability is more likely on steep long downhills. Before descending steep or long downhill grades, slow down and downshift. Do not make sudden downshifts when descending steep or long downhill grades. Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

●Do not tow a trailer when the compact spare tire is installed on your vehi-

cle. ■Hitch

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be physically capable of towing a higher weight, the operator must determine the maximum weight rating of the particular hitch assembly and never exceed the maximum weight rating specified for the trailer-hitch. Exceeding the maximum weight rating set by the trailer-hitch manufacturer can cause an accident resulting in death or serious personal injuries.

374

SIENNA_U (OM45477U)

2-5. Driving information

CAUTION

■When towing a trailer

Toyota recommends trailers with brakes that conform to any applicable fed- eral and state/provincial regulations. ●If the gross trailer weight exceeds unbraked TWR, trailer brakes are required. Toyota recommends trailers with brakes that conform to all appli- cable federal and state/provincial regulations.

●Never tap into your vehicle’s hydraulic system, as this will lower the vehi-

cle’s braking effectiveness.

●Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

NOTICE

■When installing a trailer hitch

Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage.

■Do not directly splice trailer lights

Do not directly splice trailer lights. Directly splicing trailer lights may damage your vehicle’s electrical system and cause a malfunction.

375

SIENNA_U (OM45477U)

2-5. Driving information Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

ITN25N009

■To prevent causing serious damage to the transaxle and Active Torque

Control 4WD system (AWD models)

2WD models: Never tow this vehicle from the rear with the front wheels on the ground. This may cause serious damage to the transaxle.

AWD models: Never tow this vehicle with any of the wheels on the ground. This may cause serious damage to the tran- saxle and Active Torque Control 4WD system.

ITN25N010

ITN25N011

376

SIENNA_U (OM45477U)

2-5. Driving information

377

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger Front manual air conditioning system∗

Driver’s side temperature control dial

Front fan speed

Air outlet selector buttons

Rear temperature control dial

Front air conditioning on/off switch

Off

Windshield defogger

Passenger’s side temperature control dial

Rear fan speed

Outside air or recirculated air mode

Adjusting the settings

■ Basic setting STEP 1

To turn on the air conditioning system and adjust the fan

speed, press “∧” on

to increase the fan speed and “∨” to

decrease the fan speed. The fan speed is shown on the control panel. (6 levels) Press

to turn the fan off.

∗: If equipped

380

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

STEP 2

Driver’s side temperature control dial Turn the temperature control dial clockwise (warm) or coun- terclockwise (cool).

If

is not pressed, the system will blow ambient temperature air

or heated air. For quick cooling, turn the temperature control dial to the “MAX A/C” position. The air conditioning will automatically turn on and the air circulation mode will be set to recirculated air mode. When the dial is in the “MAX A/C” position, the air conditioning sys-

tem cannot be turned off even if

is pressed.

Front passenger’s side temperature control dial Turn the temperature control dial clockwise (warm) or counter clockwise (cool).

381

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

STEP 3

To change the air outlets, press

or

Air flows as shown below according to the mode selected.

Air flows to the upper body.

Air flows to the upper body and feet.

Air flows mainly to the feet.

382

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

Air flows to the feet and the windshield defogger operates.

■ Switching between outside air and recirculated air modes

Press

The mode switches between outside air mode (introduces air from out- side the vehicle) (indicator off) and recirculated air mode (recycles air inside the vehicle) (indicator on) each time the button is pressed.

Changing the rear setting

■ Adjusting the temperature setting

Turn the rear temperature control dial clockwise (increase) or counterclockwise (decrease).

When the rear temperature control dial is turned to “REAR CTRL”, the rear temperature and fan speed can be operated from the rear air conditioning control panel. (→P. 398)

383

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

■ Adjusting rear fan speed

Press “∧” on

to increase the fan speed and “∨” to decrease

the fan speed. The fan speed is shown on the control panel. (4 levels)

Press

to turn the fan off.

Defogging the windshield

Press

The air conditioning system oper- ates automatically. Recirculated air mode will auto- matically switch to outside air mode. It is not possible to return to recirculated air mode when the switch is on.

Pressing

again will revert

to the previous air outlet mode.

384

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Center outlets

Direct air flow to the left or right, up or down.

Right and left side outlets

Adjusting: Direct air flow to the left or right, up or down.

Opening and closing:

Close the vent. Open the vent.

385

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

■Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

■When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the temperature setting.

■When the indicator light on

flashes

Press and turn off the air conditioning system before turning it on once more. There may be a problem in the air conditioning system if the indicator light continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer.

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off.

386

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

CAUTION

■To prevent the windshield from fogging up

Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the wind- shield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is stopped.

387

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger Front automatic air conditioning system∗

Airflow and outlets are automatically adjusted according to the tem- perature setting. Control panel

Changes the front air outlets used

Front air conditioning on/off switch Rear fan speed

Driver’s side temperature control dial

Changes the rear air outlets used Simultaneous mode

Automatic mode

Passenger’s side temperature control

Front fan speed

Windshield defogger

Off

Rear temperature control

Rear air conditioning on/off switch

Outside air or recirculated air mode

∗: If equipped

388

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

Multi-information display

Front Airflow display

Driver’s side temperature setting display

Air conditioning on indicator

Rear fan speed display

Automatic mode indicator

Passenger’s side temperature setting display

Front fan speed display

Rear airflow display

Rear temperature setting display

Using the automatic mode

STEP 1

Press

The air conditioning system will begin to operate. In outside air or recirculated air mode, air outlets, fan speed and air conditioning on/ off are automatically adjusted according to the temperature setting. “AUTO” will be displayed on the multi-information display. Turn the temperature control dial clockwise (warm) or coun- terclockwise (cool). The temperature for the driver and passenger seat can be set sepa- rately.

STEP 2

389

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

Adjusting the settings

■ Adjusting the temperature setting

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool). The air conditioning system switches between individual and simulta-

neous modes each time

is pressed.

Individual mode: The temperature for the driver’s, passenger’s and rear seats can be set separately. Operating the passenger’s side or rear temperature control will enter individual mode.

Simultaneous mode: Only the temperature control dial (driver’s side) can

be used to adjust the temperature for all seats.

■ Adjusting the fan speed

Press “∧” (increase) or “∨” (decrease) on

The fan speed is shown on the display. (7 levels)

Press

to turn the fan off.

390

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

Adjusting the settings manually

■ Basic setting STEP 1

To turn on the air conditioning system and adjust the fan

speed, press “∧” on

to increase the fan speed and “∨” to

decrease the fan speed.

Press

to turn the fan off.

STEP 2

To adjust the temperature setting, turn the temperature control dial (driver’s side) clockwise to increase the temperature and turn the temperature control dial (driver’s side) counterclock- wise to decrease the temperature.

When

is pressed or the passenger’s side temperature

control is pressed, the temperature for the driver and passen- ger seats can be adjusted separately.

STEP 3

Press

391

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

The air outlets switch each time shown on the display indicates the following.

is pressed. The air flow

Air flows to the upper body.

Air flows to the upper body and feet.

Air flows mainly to the feet.

392

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

Air flows to the feet and the windshield defogger operates.

■ Switching between outside air and recirculated air modes

Press

The mode switches between outside air mode (introduces air from out- side the vehicle) (indicator off) and recirculated air mode (recycles air inside the vehicle) (indicator on) each time the button is pressed.

Changing the rear setting

■ Adjusting the temperature setting

STEP 1

Press

(indicator on).

STEP 2

Press “

” on

to increase the temperature and “

” to

decrease the temperature. The air conditioning system switches between individual and simul-

taneous modes each time

is pressed.

393

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

■ Adjusting the fan speed

Press “∧” on

to increase the fan speed and “∨” to decrease

the fan speed.

Press

to turn the fan off.

■ Changing the air outlets

Press

The air outlets switch each time the button is pressed. (→P. 402)

Defogging the windshield

Press

The air conditioning system oper- ates automatically. Recirculated air mode will auto- matically switch to outside air mode. It is not possible to return to recirculated air mode when the switch is on.

Pressing to the previous air outlet mode.

again will revert

394

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Center outlets

Direct air flow to the left or right, up or down.

Right and left side outlets

Adjusting: Direct air flow to the left or right, up or down.

Opening and closing:

Close the vent. Open the vent.

395

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

■Using the automatic mode

Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions. As a result, the following may occur.

●Immediately after

is pressed, the fan may stop for a while until

warm or cool air is ready to flow.

●Cool air may flow to the area around the upper body when the heater is

on.

■Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used

■Switching between outside air and recirculated air modes

Recirculated air mode or outside air mode may be automatically switched to in accordance with the temperature setting and the inside temperature.

■Window defogger feature

Recirculated air mode may automatically switch to outside air mode in situa- tions where the windows need to be defogged.

■Temperature display

The temperature display (English/U.S. Customary System and metric units) on the trip information display can be changed. (→P. 256)

■When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the temperature setting.

■When outside temperature approaches 32°F (0°C)

The air conditioning system may not operate even when

is pressed.

396

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

■When the “A/C ON” in the multi-information display flashes

and turn off the air conditioning system before turning it on Press once more. There may be a problem in the air conditioning system if the indi- cator light continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer.

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

• It is recommended that the air conditioning system be set to outside air

mode prior to turning the vehicle off.

• The start timing of the blower may be delayed for a short period of time immediately after the air conditioning system is started in automatic mode.

CAUTION

■To prevent the windshield from fogging up

during cool air operation in extremely humid weather. The Do not use difference between the temperature of the outside air and that of the wind- shield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is stopped.

397

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger Rear manual air conditioning system∗

Changes the air outlet used

Fan speed control dial

Temperature control dial

Adjusting the settings

■ Adjusting the temperature setting

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).

■ Adjusting the fan speed

Turn the fan speed control dial clockwise (increase) or counter- clockwise (decrease).

■ The temperature setting and fan speed will only function

If the rear temperature dial on the front air conditioning controls is in the “REAR CTRL” position.

∗: If equipped

398

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

■ Changing the air outlets

Press the desired

Air flows as shown below according to the mode selected.

Air flows to the upper body.

Air flows to the upper body and feet.

Air flows to the feet.

399

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Direct air flow to the front or rear, up or down.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is off.

400

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger Rear automatic air conditioning system∗

Airflow and outlets are automatically adjusted according to the tem- perature setting.

Fan speed display

Temperature setting display

Simultaneous mode indicator

Fan speed control

Airflow display

Temperature setting

Automatic mode

Off

Changes the air outlet used

Automatic mode indicator

Using the automatic mode

STEP 1

Press

The air conditioning system begins to operate. Air outlets and fan speed are automatically adjusted according to the temperature set- ting.

STEP 2

Press “∧” on

to increase the temperature and “∨” to

decrease the temperature.

∗: If equipped 401

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

Adjusting the settings

■ Adjusting the temperature setting

Press “∧” on

to increase the temperature and “∨” to

decrease the temperature. ■ Changing the air outlets

Press the desired

Air flows as shown below according to the mode selected.

Air flows to the upper body.

Air flows to the upper body and feet.

402

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

Air flows to the feet.

■ Adjusting the fan speed

Press “∧” on

to increase the fan speed and “∨” to decrease

the fan speed.

Press

to turn the fan off.

Adjusting the position of the air outlets

Direct air flow to the front or rear, up or down.

403

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

■Temperature display

The temperature display (English/U.S. Customary System and metric units) on the trip information display can be changed. (→P. 256)

■When the front air conditioning system is in simultaneous mode

“SYNC” is shown on the display. The rear air conditioning system controls will continue to function. (→P. 390)

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is off.

404

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers, and windshield wiper de-icer

The rear window defogger is used to defog the rear window. The out- side rear view mirror defoggers*1 are used to remove frost, dew or raindrops from the outside rear view mirrors. The windshield wiper de-icer*2 is used to prevent ice from building up on the windshield and wiper blades. Vehicles with manual air conditioning system

Turns the rear window and outside rear view mirror defog- gers and windshield de-icer on/off.

The defoggers and de-icer will automatically turn off after approximately 15 minutes. If outside temperature is below 32°F (0°C), this will extend by 45 minutes.

Vehicles with automatic air conditioning system

*1: Vehicles with outside rear view mirror defoggers *2: Vehicles with windshield wiper de-icer

405

SIENNA_U (OM45477U)

3-1. Using the air conditioning system and defogger

■The defogger can be operated when Vehicles without a smart key system The engine switch is in the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is IGNITION ON mode.

■Outside rear view mirror defoggers (vehicles with outside rear view

mirror defoggers) Turning the rear window defogger on will turn the outside rear view mirror defoggers on.

■The outside rear view mirror defoggers and windshield wiper de-icer

(vehicles with windshield wiper de-icer) Turning the rear window defogger on will turn the outside rear view mirror defoggers and windshield wiper de-icer on.

CAUTION

■Outside rear view mirror defoggers (vehicles with outside rear view

mirror defoggers) The surfaces of the outside rear view mirrors become hot. Do not touch them to prevent from burning yourself.

■When the windshield wiper de-icer is on (vehicles with windshield

wiper de-icer) Do not touch the glass at the lower part of the windshield or to the side of the front pillars as the surfaces can become very hot and burn you.

406

SIENNA_U (OM45477U)

3-2. Using the audio system Audio system type∗

With navigation system

Owners of models equipped with a navigation system should refer to the “NAVIGATION SYSTEM OWNER’S MANUAL”.

Without navigation system

Type A and B: CD player with AM/FM radio Type C: CD player with changer and AM/FM radio.

Type A

∗: If equipped 407

SIENNA_U (OM45477U)

3-2. Using the audio system

Type B

Type C

408

SIENNA_U (OM45477U)

3-2. Using the audio system

Title

Using the radio Using the CD player Playing back MP3 and WMA discs Operating an iPod Operating a USB memory Optimal use of the audio system Using the AUX port Using the steering switches

Page P. 412
P. 422
P. 431
P. 442
P. 449
P. 457
P. 462
P. 463

Language settings (type B and C)

The language used for all voice guidance, voice recognition and mes- sages may be changed.

STEP 1

Press

STEP 2

Press

that corresponds to “MORE”.

STEP 3

Press

that corresponds to “LANG”.

STEP 4

Press

that corresponds to the desired language.

For vehicles sold in the U.S.A. “ENG” (English) or “ESP” (Spanish) For vehicles sold in the Canada “ENG” (English) or “FRAN” (French)