2007 Toyota Sienna Owners Manual

07 SIENNA_U (L/O 0612)

“AUTO” button For automatic operation of the rear air conditioning, press the “AUTO” button. An indicator light will illuminate to show that the automatic operation mode has been selected. In the automatic operation mode, the air conditioning selects the most suitable fan speed and air flow according to the tem- perature. You may use manual controls if you want to select your own settings. Fan speed selectors Push the button to select the fan speed mode. In the automatic operation mode, the fan speed is adjusted automatically unless you desire another fan speed mode.

the

increase

temperature, press

Temperature selectors To the “(cid:1)” side. To decrease it, press the “(cid:2)” side. “LO” appears when you adjust to maxi- mum cooling, and “HI” appears when you adjust to maximum warming. When “SYNC” appears on the rear tem- perature display, rear controls cannot be used. Use the controls on the front control panel. To cancel this function, push the “SYNC” button. For details about the “SYNC” button, see “Front automatic air conditioning system” on page 324 in this Section. The temperature display changes between “(cid:2)C” and “(cid:2)F” when the unit of the outside temperature display is changed. (For de- tails, see “Multi−information display” on page 338 in Section 1−10.) “REAR” button To turn on the rear air conditioning system front control panel, push the using the button. To turn the button again. “OFF” button Push the button to turn off the rear air conditioning system.

it off, push

Air flow selectors Push the button to select the vents used for air flow. 1. Panel—Air flows from the roof panel

vents.

2. Bi−level—Air flows from both the roof

panel vents and floor vent.

3. Floor—Air flows from the floor vent.

333

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

—Air flow selector settings

Air conditioning filter—

The air conditioning filter information label is placed on the right side of the glove box as shown and indicates that a filter has been installed. The air conditioning filter prevents dust from entering the vehicle through the air conditioning vent.

The air conditioning filter is behind the glove box.

334

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

—Checking and replacing the air conditioning filter The air conditioning filter may clog af- ter long use. The filter may need to be replaced if the air flow of the air condi- tioning and heater experiences extreme reductions in operating efficiency, or if the windows begin to fog up easily. To maintain the air conditioning efficiency, inspect and replace the air conditioning filter according to the maintenance sched- ule. In dusty areas or areas with heavy traffic flow, such as inner city or desert areas, early replacement may be required. (For scheduled maintenance information, please refer the “Scheduled Mainte- nance Guide” or “Owner’s Manual Supple- ment”.)

to

1. Open the glove box, and slide off

the damper as shown.

2. Push in each side of the glove box

to disconnect the claws.

335

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

3. Remove the filter case from the filter

outlet as shown in the illustration.

4. Remove

case.

the

filter

from

the

filter

5. Inspect the filter on the surface. If it is dirty, it should be replaced.

INFORMATION

The air filter should be installed prop- erly in position. The use of air condi- tioning with the air filter removed may cause deteriorated dustproof per- formance and then affect air condi- tioning performance.

336

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

SECTION 1− 10

OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Multi−information display Clock Conversation mirror Toyota park assist system Rear view monitor system Power outlets Glove box Garage door opener box Auxiliary boxes Coin holder Cup holders Bottle holders Storage box Removable console box Note pad holder Front seat side table Coat hooks Grocery bag hooks Cargo net hooks Tie−down hooks Roof luggage carrier Sun shade Floor mat

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

338
350
351
352
361
364
366
367
369
372
372
374
375
375
380
380
382
382
383
384
384
385
386

337

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

Multi−information display—

07 SIENNA_U (L/O 0612)

1. “E/M” button 2. Garage door opener buttons 3. “MODE” button 4. Garage door opener indicator 5. Outside temperature and cruise

information display

6. Compass

338

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

the

the multi−information display

—Before using the multi−information display Operate with the ignition switch on. to When “ON”, the last previously used mode dis- played just before the ignition switch is turned off will appear. When lights are turned on, the brightness of the display will be reduced.

instrument panel

ignition switch

turned

the

is

07 SIENNA_U (L/O 0612)

“E/M” button This button is used to switch between English/U.S. Customary System and metric units. Each time you push this button, the display switches. This is also linked to the front and rear air conditioning displays. The display variations are as follows;

Indication

English/U.S. Customary System (E) Metric (M)

Outside

temperature

Instantaneous fuel consumption/

Average fuel consumption

Distance to empty

(cid:4)F

(cid:4)C

MPG

L/100 km

MI

km

339

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

—Garage door opener

Buttons

“MODE” button This button is used to select the item. Every time you push the “MODE” button, the display toggles. For more details, see “—Outside tempera- ture and cruise information display” on page 344.

CAUTION

Indicator light

Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

(cid:3)

The garage door opener ( Universal Transceiver) is manufactured under license from HomeLink(cid:3) and can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, and security systems, etc.

transmitter prior

(a) Programming the HomeLink(cid:3) The HomeLink(cid:3) in your vehicle has 3
buttons and you can store one program for each button. To ensure correct programming into the HomeLink(cid:3), install a new battery in the hand−held to program- ming. The battery side of the hand−held trans- mitter must be pointed away the HomeLink(cid:3) during the programming pro- cess. For Canadian users, follow the procedure “Programming an entrance gate/Pro- in gramming all devices the Canadian market”. 1. Decide which of 3 HomeLink(cid:3) buttons you want to program. Push and hold down one of the buttons until the indi- cator corresponding to the selected channel begins to flash.

from

in

340

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

HomeLink(cid:5)

25 to 75 mm (1 to 3 in.)

Hand−held garage transmitter

2. Place your hand−held garage transmit- ter 25 to 75 mm (1 to 3 in.) away from the surface of the HomeLink(cid:3).

Keep the indicator light on the HomeLink(cid:3) in view while programming.

3. Simultaneously press and hold

the hand−held garage transmitter button along with the selected HomeLink(cid:3) but- ton.

Do not release the buttons until step 4
has been completed. 4. When

the HomeLink(cid:3) changes from a slow to a rapid flash after 20 seconds, you can release both buttons.

light on

indicator

the

5. Test the operation of the HomeLink(cid:3) by pressing the newly programmed button. If programming a garage door opener, check to see if the garage door opens and closes.

If the garage door does not operate, iden- tify if your garage transmitter is of the “Rolling Code” type. Press and hold the programmed HomeLink(cid:3) button. The ga- rage door has the rolling code feature if the HomeLink(cid:3)) the flashes rapidly and then remains lit after 2 seconds. If your garage transmitter is the “Rolling Code” type, proceed to the heading “Programming a rolling code sys- tem”.

indicator

light

(on

341

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

6. Repeat steps 2 through 5 for each re- maining HomeLink(cid:3) button to program another device.

it

is

to

is necessary

Programming a rolling code system “Rolling Code” If your device equipped, follow steps 1 through 4 under the heading “Programming the HomeLink(cid:3)” before proceeding with the steps listed below. 1. Locate the “training” button on the ceil- ing mounted garage door opener motor. The exact the button may vary by brand of garage door opener. Refer the owner’s guide supplied by the garage door opener manufacturer for the location of this “training” button.

location and color of

to

2. Press the “training” button on the ceil- ing mounted garage door opener motor. Following this step, you have 30 seconds in which to initiate step 3 below. 3. Press and release the vehicle’s pro- grammed HomeLink(cid:3) button twice. The garage door may open. the door does open, the programming process is complete. If the door does not open, press and release the button a third time. This third press and release will complete the programming process by opening the garage door.

If

342

07 SIENNA_U (L/O 0612)

now

should

recognize

The ceiling mounted garage door opener motor the HomeLink(cid:3) unit and be able activate the garage door up/down. 4. Repeat steps 1 through 3 for each re- maining HomeLink(cid:3) button to program another rolling code system.

Programming an entrance gate/program- ming all devices in the Canadian market 1. Decide which of the 3 HomeLink(cid:3) but-

2. Place

your

tons you want to program. hand−held

gate/device transmitter 25 to 75 mm (1 to 3 in.) away the HomeLink(cid:3).

surface

from

the

of

Keep the indicator light on the HomeLink(cid:3) in view while programming. 3. Press

selected

hold

and

the

HomeLink(cid:3) button.

4. Continuously press and release (cycle) transmitter the hand−held gate/device button every two seconds until step 5
is complete. the

the HomeLink(cid:3) changes from a slow to a rapid flash after 20 seconds, you can release both buttons.

light on

5. When

indicator

6. Test the operation of the HomeLink(cid:3) by pressing the newly programmed button. Check to see if the gate/device oper- ates correctly.

7. Repeat steps 1 through 6 for each re- maining HomeLink(cid:3) button to program another device.

Programming other devices To program other devices such as home security systems, home door locks or lighting, contact your authorized Toyota dealer for assistance. Reprogramming a button Individual HomeLink(cid:3) buttons cannot be erased, however, to reprogram a single button, follow the procedure “Programming the HomeLink(cid:3)”. (b) Operating the HomeLink(cid:3) To operate the appropriate HomeLink(cid:3) button to activate the programmed device. The HomeLink(cid:3) indicator light should come on. The HomeLink(cid:3) continues to send the signal for up the button is pressed.

the HomeLink(cid:3), press

to 20 seconds as

long as

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

your

For additional programming assistance with Universal Transceiver call the: (cid:2) Toyota Customer Experience Center at

HomeLink(cid:3)

1−800−331−4331 (U.S.A.)

(cid:2) Toyota Canada Customer

Interaction

Centre at 1−888−869−6828 (Canada) Refer to HomeLink(cid:3) on the internet at: WWW.HOMELINK.COM

CAUTION

(cid:2) When programming the HomeLink(cid:3) Universal Transceiver, you may be operating a garage door or other device. Make sure people and ob- jects are out of the way of the ga- rage door or other device to pre- vent potential harm or damage.

(cid:2) Do not use this HomeLink(cid:3) Univer- sal Transceiver with any garage door opener that lacks the safety stop and reverse feature as re- quired by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982.) A garage door open- er which cannot detect an object (signaling the door to stop and re- verse), does not meet current feder- al safety standards. Using a garage door opener without these features increases risk of serious injury or death.

343

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

(c) Erasing

the

entire HomeLink(cid:3)

memory (all three programs)

To erase all previously programmed codes at one time, press and hold down the 2
outside buttons for 20 seconds until the indicator light flashes. If you sell your vehicle, be sure to erase the HomeLink(cid:3) the programs stored memory.

in

received,

This device complies with Part 15 of the FCC Rules and with RSS−210 of the IC Rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer- ence interference that may cause undesired operation. WARNING: This transmitter has been tested and complies with FCC and IC rules. Changes or modifications not expressly approved by the party re- sponsible for compliance could void the user’s authority to operate the device.

including

344

07 SIENNA_U (L/O 0612)

—Outside temperature and cruise information display

The outside temperature and cruise in- formation display indicates the follow- ing information. 1. Outside temperature 2. Average fuel consumption 3. Instantaneous fuel consumption 4. Distance to empty 5. Display off (no compass) Every time you push the “MODE” button, the display toggles through this informa- tion. During the off mode, the compass display is also turned off. The displayed values in the cruise infor- mation display indicate general driving conditions. Accuracy varies with driving habits and road conditions. To set the unit, push the “E/M” button until the desired unit display appears. (At this time, front and rear air conditioning displays also change.)

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

1. Outside temperature (“OUTSIDE (cid:4)C”

or “OUTSIDE (cid:4)F”)

3. Instantaneous fuel consumption

(“INST MPG” or “INST L/100 km”)

Every time you refuel the vehicle, the cal- culation is reset. The actual driving range varies with driv- ing habits and road conditions. If fuel con- sumption is good, the driving range will be longer. If fuel consumption is poor, the driving range will be shorter.

The instantaneous fuel consumption is calculated and displayed based on dis- tance and fuel consumption for 1 sec- onds with the engine running. The displayed value is updated every 2
seconds. Note that an accurate figure may not be shown in the following cases. (cid:2) The vehicle is stopped with the engine running. (The display will indicate the extremely high fuel consumption.) is driving down a

long slope applying the engine brake. (The display will indicate the extremely low fuel consumption.)

(cid:2) The vehicle

from

indi-

temperature

the outside air

The outside temperature display cates the outside air temperature. The displayed value is updated every 1
second. The displayed ranges −30(cid:4)C (−22(cid:4)F) up to 50(cid:4)C (122(cid:4)F). If an abnormality exists in the connection of temperature sensor, “−−(cid:4)C” (“−−(cid:4)F”) will appear on the display. If “−−(cid:4)C” (“−−(cid:4)F”) appears on the display, contact your Toyota dealer. There may be a case that “−−(cid:4)C” (“−−(cid:4)F”) appears momentarily when the ignition is quickly turned to “ON”. It is normal if it goes out soon. 2. Average fuel consumption

(“AVG MPG” or “AVG L/100 km”)

total

Average fuel consumption is calculated and displayed based on total driving distance and fuel consumption with the engine running. The displayed value is updated every 1
seconds. To reset the calculations, return the mode to “AVG” and push and hold the “MODE” and “E/M” button simultaneously for 2 sec- onds.

The calculation is reset when the ignition switch is turned off. 4. Distance to empty

(“DTE MI” or “DTE km”)

fuel

The distance the vehicle can travel with the remaining is calculated and displayed based on the quantity of re- maining fuel and past fuel consumption. The displayed value is updated every 1
second.

345

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

—Compass

the direction

If the system does not operate properly, contact your Toyota dealer.

indicated or

is not

The compass may not show the correct direction in the following conditions: (cid:2) The vehicle is stopped immediately af-

ter turning. The compass does not adjust while the vehicle is stopped.

(cid:2) The ignition switch is turned off imme-

diately after turning.

(cid:2) The vehicle is on an inclined surface. (cid:2) The vehicle is in a place where the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

(cid:2) The vehicle is magnetized. (There is a magnet or a metal object on or near the roof.)

(cid:2) The battery has been disconnected. The compass works to calibrate the direc- tion automatically while the vehicle is in motion, if deviation is small. For additional precision or see calibrating, COMPASS” below.

for complete THE

“CALIBRATING

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

indicates

the vehicle

is heading.

the direction The compass that the above case, it shows that the vehicle is heading south. The direction display is updated every 2
seconds.

In

Displays

NE SE SW NW

346

Directions

North

Northeast

East

Southeast

South

Southwest

West

Northwest

07 SIENNA_U (L/O 0612)

the

from

CALIBRATING THE COMPASS (deviation calibration) the compass The direction display on deviates true direction deter- mined by the earth’s magnetic field. The angle of deviation varies according to the geographic position of the vehicle. To adjust for this deviation; 1. Stop the vehicle in a level place and switch the display to the outside tem- perature. (To switch to this mode, see “—Outside temperature and cruise in- formation display” on page 344.)

2. Push and hold both the “MODE” and “E/M” buttons simultaneously for 5 sec- onds until the “VAR” indication appears on the compass display.

3. Push

the “E/M” button several

times until the desired zone number appears on the compass display.

If the button is not pushed for 10 sec- onds, the display returns to the compass/ outside temperature mode and the number that is last set is memorized. To select the zone where the vehicle is currently following map.

located, refer

the

to

The compass sensor is on the roof of the vehicle.

NOTICE

Do not put magnets or a metal object on or near the roof of the vehicle. Doing this may cause malfunction of the compass sensor.

347

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Samoa: Guam: Saipan:

After calibration, leaving the system for several seconds returns to the compass mode.

CAUTION

Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

Zone number

348

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

2. Push and hold both the “MODE” and “E/M” buttons simultaneously for 10
seconds until the “CAL” indication ap- pears on the compass display. (At this time, the compass display is locked in “N”.)

3. Drive the vehicle in a circle at 8 km/h (5 mph) or less. If there is not enough space to drive in a circle, drive around the block.

When the “CAL” indication goes off and the compass returns to the normal mode, calibration is complete. If you want to restart the calibration be- fore the “MODE” and “E/M” buttons simultaneously for 10 seconds again.

is complete, push both of

it

349

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

the direction display on

CALIBRATING THE COMPASS (circling calibration) Sometimes the compass may not change after a turn. In this case, the compass needs to be cali- brated. To calibrate the compass manually, do the following; 1. Stop the vehicle in a level place and switch the display to the outside tem- perature. (To switch to this mode, see “—Outside temperature and cruise in- formation display” on page 344.)

07 SIENNA_U (L/O 0612)

Clock

Perform circling calibration just after you have purchased your Toyota. And then always perform circling calibration after the battery has been removed, re- placed or disconnected. (cid:2) Do not perform circling calibration of the compass the earth’s magnetic field is subject to in- terference by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a crossing, near a large vehicle, etc.).

in a place where

(cid:2) During calibration, do not operate elec- tric systems (moon roof, power win- dows, etc.) as they may interfere with the calibration.

CAUTION

(cid:2) When doing the circling calibration, be sure to secure a wide space, and watch out for people and ve- hicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.

(cid:2) Do not adjust the display while the vehicle is moving. Be sure to adjust the display only when the vehicle is stopped.

350

With manual air conditioning system

With automatic air conditioning system

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. The key must be in the “ACC” or “ON” position. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00. When lights are turned on, the brightness of the time in- dication will be reduced.

instrument panel

the

07 SIENNA_U (L/O 0612)

Conversation mirror The conversation mirror is designed for the driver and front passenger to be able to look at the rear passengers without turning around.

CAUTION

Do not adjust the mirror while the vehicle is moving. Be sure to adjust the mirror only when the vehicle is stopped.

To use the mirror, push it down.

351

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Toyota park assist system (type A)

1: Rear sensors 2: Rear corner sensors 3: Front corner sensors

The mirror angle can be adjusted by push- ing its edge.

352

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

The Toyota park assist system is de- signed to inform you of the approxi- mate distance between your vehicle and an obstruction by indicator and buzzer when parking the vehicle. This system uses sensors to detect obstructions. This system works when the ignition key is at the “ON” position and the transmis- sion is not in the “P” position. (cid:2) Rear and

rear corner sensors work only when the transmission is in the “R” position.

(cid:2) Front corner sensors works when the

transmission is in the “R” position.

(cid:2) Front corner sensors works when the transmission is not in the “P” or “R” position and vehicle speed is approxi- mate 10 km/h (6 mph) or less.

To turn on: Push the switch. The indicator comes on and the buzzer will sound. To turn off: Push the switch again.

In the following cases, the buzzer will sound several times and the indicator will stay on to indicate that the system is not working properly. (cid:2) When the temperature is extremely low. (cid:2) When any of the sensors are malfunc-

tion.

If the indicator is continuously on, have your Toyota dealer check the system. If the you do not hear clean the sensors with soft cloth.

indicator remains blinking but the buzzer sound,

353

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

Rear sensors

Rear corner sensors

Front corner sensors

354

07 SIENNA_U (L/O 0612)

Front corner sensors

Distance shown as C in mm (in.) Approximately 600—400 (23.6—15.7) Approximately 400—250 (15.7—9.8) Approximately 250 (9.8) or less

Indicator and

buzzer

Intermittent

Fast intermittent

Continuous

This system is designed to inform you of the approximate distance between your vehicle and an obstacle by indicator and buzzer. Rear sensors

Distance shown as A in mm (in.) Approximately 1800—900
(70.9—35.4) Approximately 900—550 (35.4—21.7) Approximately 550 (21.7) or less

Rear corner sensors

Distance shown as B in mm (in.) Approximately 850—520 (33.5—20.5) Approximately 520—250 (20.5—9.8) Approximately 250 (9.8) or less

Indicator and

buzzer

Intermittent

Fast intermittent

Continuous

Indicator and

buzzer

Intermittent

Fast intermittent

Continuous

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

1: Front sensors 2: Rear corner sensors 3: Rear sensors

07 SIENNA_U (L/O 0612)

Perceptible area 1800 mm (70.9 in.) A: Approximately 850 mm (33.5 in.) B: Approximately C: Approximately 600 mm (23.6 in.) Perceptible area is limited as shown in the previous illustration. Check the area around the vehicle before driving and start driving slowly. The maximum detection distance of the sensor varies depending on the size of the obstacle. The sensor can detect a large obstacle, such as a wall, up to 1800
mm (70.9 in.) away. However, the detec- tion distance of a thin obstacle, such as a pole, is less than 1800 mm (70.9 in.).

355

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

For vehicles sold in Canada

This ISM device Canadian ICES−001.

compiles with

CAUTION

(cid:2) The Toyota park assist system

is intended as an aid to assist you to park and is not a substitute for your personal judgment. Make your driving decisions based on your ob- servations.

(cid:2) Do not attach accessories or other objects to the vehicle within the sensor perceptible area. Doing so may cause the system to malfunc- tion, which might result in an acci- dent.

(cid:2) In certain situations,

the system will not function properly and when the vehicle approaches certain ob- jects, the system will not detect those objects. Therefore, always ob- serve the area around the vehicle and do not rely solely on the sys- tem.

356

In the following cases, the system may not work properly. (cid:2) When ice, snow, mud or other objects

build up on the sensor.

(cid:2) When the vehicle is parked in extreme- ly high or extremely low temperature for a long period.

(cid:2) When driving on bumpy or graveled

roads or on grass

(cid:2) When a device such as a horn from another vehicle, motorcycle engine, or an air brake sound from a heavy−duty vehicle, issues ultrasonic waves, near your vehicle

(cid:2) When attaching a two−way radio anten-

na

(cid:2) When rain or water splashes on the

sensor.

(cid:2) When operating the vehicle on an in-

clined surface

(cid:2) When a radio antenna or fender pole

is mounted on your vehicle.

(cid:2) When a

towing hitch is mounted on

your vehicle.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

The system may not detect the follow- ing. (cid:2) Thin objects such as a wire or rope (cid:2) Objects with a surface area too small reflect ultrasonic waves such as

to wire gauze

(cid:2) Sound wave absorbing objects or mate-

rial such as cotton or snow

(cid:2) A person near the vehicle (depending

on the type of clothes worn)

(cid:2) Objects with a sharp edge (cid:2) Small or short objects (cid:2) Tall objects with an upper part project-

ing toward the vehicle

the

(cid:2) Objects just under the bumper (cid:2) Objects very close to your vehicle In Toyota dealer check the system. (cid:2) When the bumper is damaged. (cid:2) When the indicator is continuously on.

following cases, have your

07 SIENNA_U (L/O 0612)

Toyota park assist system (type B)

To turn on: Push the switch. The indicator comes on and the buzzer will sound. To turn off: Push the switch again.

1: Rear sensors 2: Rear corner sensors

The Toyota park assist system is de- signed to inform you of the approxi- mate distance between your vehicle and an obstruction by indicator and buzzer when parking the vehicle. This system uses sensors to detect obstructions. This system works when the ignition key is at the “ON” position and the transmis- sion is in the “R” position. The sensors work only when the transmis- sion is in the “R” position.

357

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Rear sensors

In the following cases, the buzzer will sound several times and the indicator will stay on to indicate that the system is not working properly. (cid:2) When the temperature is extremely low. (cid:2) When any of the sensors are malfunc-

tion.

If the indicator is continuously on, have your Toyota dealer check the system. If the you do not hear clean the sensors with soft cloth.

indicator remains blinking but the buzzer sound,

Rear corner sensors

358

This system is designed to inform you of the approximate distance between your vehicle and an obstacle by indicator and buzzer. Rear sensors

Distance shown as A in mm (in.) Approximately 1800—900
(70.9—35.4) Approximately 900—550 (35.4—21.7) Approximately 550 (21.7) or less

Rear corner sensors

Distance shown as B in mm (in.) Approximately 850—520 (33.5—20.5) Approximately 520—250 (20.5—9.8) Approximately 250 (9.8) or less

Indicator and

buzzer

Intermittent

Fast intermittent

Continuous

Indicator and

buzzer

Intermittent

Fast intermittent

Continuous

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Perceptible area 1800 mm (70.9 in.) A: Approximately 850 mm (33.5 in.) B: Approximately Perceptible area is limited as shown in the previous illustration. Check the area around the vehicle before driving and start driving slowly. The maximum detection distance of the sensor varies depending on the size of the obstacle. The sensor can detect a large obstacle, such as a wall, up to 1800
mm (70.9 in.) away. However, the detec- tion distance of a thin obstacle, such as a pole, is less than 1800 mm (70.9 in.).

CAUTION

(cid:2) The Toyota park assist system

is intended as an aid to assist you to park and is not a substitute for your personal judgment. Make your driving decisions based on your ob- servations.

(cid:2) Do not attach accessories or other objects to the vehicle within the sensor perceptible area. Doing so may cause the system to malfunc- tion, which might result in an acci- dent.

(cid:2) In certain situations,

the system will not function properly and when the vehicle approaches certain ob- jects, the system will not detect those objects. Therefore, always ob- serve the area around the vehicle and do not rely solely on the sys- tem.

359

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

1: Rear corner sensors 2: Rear sensors

07 SIENNA_U (L/O 0612)

For vehicles sold in Canada

This ISM device Canadian ICES−001.

compiles with

In the following cases, the system may not work properly. (cid:2) When ice, snow, mud or other objects

build up on the sensor.

(cid:2) When the vehicle is parked in extreme- ly high or extremely low temperature for a long period.

The system may not detect the follow- ing. (cid:2) Thin objects such as a wire or rope (cid:2) Objects with a surface area too small reflect ultrasonic waves such as

to wire gauze

(cid:2) Sound wave absorbing objects or mate-

(cid:2) When driving on bumpy or graveled

rial such as cotton or snow

roads or on grass

(cid:2) When a device such as a horn from another vehicle, motorcycle engine, or an air brake sound from a heavy−duty vehicle, issues ultrasonic waves, near your vehicle

(cid:2) When attaching a two−way radio anten-

na

(cid:2) When rain or water splashes on the

sensor.

(cid:2) When operating the vehicle on an in-

clined surface

(cid:2) When a radio antenna or fender pole

is mounted on your vehicle.

(cid:2) When a

towing hitch is mounted on

your vehicle.

(cid:2) A person near the vehicle (depending

on the type of clothes worn)

(cid:2) Objects with a sharp edge (cid:2) Small or short objects (cid:2) Tall objects with an upper part project-

ing toward the vehicle

the

(cid:2) Objects just under the bumper (cid:2) Objects very close to your vehicle In Toyota dealer check the system. (cid:2) When the bumper is damaged. (cid:2) When the indicator is continuously on.

following cases, have your

360

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Rear view monitor system The rear view monitor system assists the driver by displaying an image of the view behind the vehicle while back- ing up. The image is displayed in re- verse on the screen. This allows the image to appear in the same manner as that of the rear view mirror. To display the rear view image on the screen, place the selector lever in the “R” position when the ignition key in the “ON” position. If you move the selector lever out of the “R” position, the previous screen. Operating another func- tion of the navigation system will display another screen. The rear view monitor system is a supple- ment device intended to assist back up. When backing up, be sure to check be- hind and all around the vehicle visually.

the screen returns

to

CAUTION

the

(cid:2) Never depend on

rear view monitor system entirely when back- ing up. Always make sure your in- tended path is clear. Use caution just as you would when backing up any vehicle.

image on

(cid:2) Never back up while looking only at the screen. The the screen is different from actual con- ditions. Depicted distances between objects and flat surfaces will differ from actual distances. If you back up while looking only at the screen, you may hit a vehicle, a person or an object. When backing up, be sure to check behind and all around the vehicle visually and with mir- rors before proceeding.

(cid:2) Do not use the system when the back door is not completely closed.

(cid:2) If the back of the vehicle is hit, the position and mounting angle of the camera may change. Be sure to have the camera’s position and mounting angle checked at your Toyota dealer.

(cid:2) If the temperature changes rapidly, such as when hot water is poured on the vehicle in cold weather, the system may not operate normally.

(cid:2) If the camera lens becomes dirty, it If cannot transmit a clear water droplets, snow, or mud ad- here to the lens, rinse with water and wipe with a soft cloth. If the lens is extremely dirty, wash it with a mild cleanser and rinse.

image.

(cid:2) Use your own eyes to confirm the vehicle’s surroundings, as the dis- played image may become faint or dark, and moving images will be distorted, or not entirely visible when is low. When backing up, be sure to check behind and all around the ve- hicle visually and with mirror before proceeding.

the outside

temperature

361

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

When replacing the tires, please consult your Toyota dealer. If you replace the tires, the area displayed on the screen may change.

AREA DISPLAYED ON SCREEN Image is displayed approximately level on screen.

362

On screen

Check surroundings for safety.

Corners of bumper

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

(cid:2) The area detected by the camera is limited. The camera does not detect objects which are close to either corner of the bumper or under the bumper.

(cid:2) The area displayed on the screen may vary according to vehicle orien- tation or road conditions.

07 SIENNA_U (L/O 0612)

(cid:2) When water droplets are adhering to the camera, or when humidity is high (for example, when it rains)

(cid:2) When

foreign matter

(for example, snow or mud) is adhering to the cam- era

(cid:2) When the sun or the beam of head- lights is shining directly into the cam- era lens

THE REAR VIEW MONITOR SYSTEM CAMERA The rear view monitor system camera is located on the back door as shown in the illustration. The camera uses a special lens. The distance of the image that ap- pears on the screen differs from the actu- al distance. In it may become difficult to see the images on the screen, even when the system is functioning. (cid:2) In the dark (for example, at night) (cid:2) When the temperature near the lens is

following cases,

the

high or low

363

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Power outlets (12 VDC)

Front

Rear

The power outlets (12 VDC) are de- signed for power supply for car acces- sories. The key must be in the “ACC” or “ON” position for the power outlets to be used.

NOTICE

(cid:1) To prevent the fuse from being blown, do not use the electricity over the total vehicle capacity of 12
VDC/120W (front and rear outlets together).

(cid:1) To prevent the battery from being discharged, do not use the power outlets longer than necessary when the engine is not running.

(cid:1) Close the power outlet lids when the power outlets are not in use. Inserting anything other than an ap- propriate plug that fits the outlet, or allowing any liquid to get into the outlet may cause electrical fail- ure or short circuits.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

Check surroundings for safety.

If a bright light (for example, sunlight re- flected off the vehicle body) is picked up by the camera, the smear effect* peculiar to the camera may occur. * : Smear effect—A phenomenon that oc- curs when a bright light (for example, sun- light reflected off is picked up by trans- mitted by light source appears to have a vertical streak above and below it.

the camera; when

the vehicle body)

the camera,

the

364

Power outlets (115 VAC)

Beside second seat

Beside third seat

07 SIENNA_U (L/O 0612)

The power outlets (115 VAC) are de- signed for use as a power supply for electric appliances in the vehicle. The key must be in the “ON” position for the power outlet to be used. The maximum capacity for this power out- let is 115 VAC/100W. If you attempt to use an appliance that requires more than 115 VAC or 100W, the protection circuit will activate and cut the power supply. The power supply will restart automatically when you use an appliance that operates within the 115 VAC/100W limits.

To use the power outlet, push the main switch on the instrument panel. An indicator light will illuminate to indicate that the power outlet is ready for use. Push the main switch once again to turn the power outlet off. When the power out- let is not in use, make sure that the main switch is turned off.

365

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

NOTICE

Certain electrical appliances may cause radio noise.

Glove box

(cid:1) To prevent the battery from being discharged, do not use the power outlet longer than necessary when the engine is not running.

(cid:1) Close the power outlet lids when the power outlets are not in use. Inserting anything other than an ap- propriate plug that fits the outlet, or allowing any liquid to get into the outlet may cause electrical fail- ure or short circuits.

The power outlet is not designed for the following electric appliances even though their power consumption is un- der 115 VAC/100W. These appliances may not operate properly. (cid:2) Appliances with high initial peak watt- age: cathode−ray tube type televisions, compressor−driven refrigerators, electric pumps, electric tools, etc.

(cid:2) Measuring devices which process pre- cise data: medical equipment, measur- ing instruments, etc.

(cid:2) Other appliances requiring an extremely stable power supply: microcomputer− controlled electric blankets, touch sen- sor lamps, etc.

366

To use the glove box: Open by pulling the lever. Lock by inserting the master key and turn- ing it clockwise. Unlock by inserting the master key and turning it counterclockwise.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.

injury

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Garage door opener box

The box is designed to store a garage door opener transmitter. Open and−loop fastener.

the cover and remove the hook−

Remove the paper strip covering the adhe- sive on back side of loop and adhere loop to back side of the transmitter near cen- ter.

Please note if transmitter has wire clip for sun visor, this clip must be removed prior to adhesion of the fastener.

367

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Remove spacers from the center panel. Place one spacer on the pin that would be below transmitter button when the cover is closed. Close the cover.

When the garage door opener transmitter is properly installed, you can operate the transmitter by pushing the center panel of the cover.

Place the transmitter with the fastener fac- ing inside of box into the box. Make sure the located above button pins.

transmitter button

is

368

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

CAUTION

(cid:2) To reduce the chance of injury in case of an accident or a sudden stop, always keep the garage door opener box closed while driving.

(cid:2) Keep the remaining spacers away

from children.

If the center panel does not contact your garage door opener transmitter: (cid:2) Check to see if spacer is on the cor-

rect pin.

(cid:2) Attach another spacer

top of original spacer. Check operation. If re- quired, continue to add spacers until contact is achieved.

to the

If the transmitter is clattering during driv- ing, fill in a piece of felt or pad to prevent the transmitter from clattering.

Auxiliary boxes To use the auxiliary box, open the lid as shown in the following illustrations. Type C—The plate in the center of the auxiliary box can be adjusted or removed as shown in the illustration. Type I—For details, see “Front seat side table” on page 380 in this Section.

CAUTION

(cid:2) To reduce the chance of injury in case of an accident or a sudden stop, always keep the auxiliary box closed while driving.

(cid:2) Type A—As these holders are de- signed for holding a light object such as an eyeglass, do not place any heavy objects in them. Heavy objects may cause the holder to open and contents to fly out result- ing in injuries.

NOTICE

Type A—During hot weather, the inte- rior of the vehicle becomes very hot. Do not leave anything flammable or deformable such as a lighter, glasses, etc. inside.

369

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Type A (driver’s side roof)

Type D (instrument panel with seat heater switches)

Position 1

Position 2

Type B (instrument panel)

Type C (instrument panel without seat heater switches)

Type E (upper side of the glove box)

370

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Type F (front door)

Type H (spare tire cover)

Type J (rear side of console box)

Type G (quarter trim)

Type I (front seat side table)

Type K (front passenger’s seat)

371

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

Coin holder

To use the coin holder, push the but- ton.

CAUTION

To reduce the chance of in case of an accident or a sudden stop while driving, keep the coin holder closed when it is not in use.

injury

372

07 SIENNA_U (L/O 0612)

Cup holders The cup holder is designed for holding cups or drink−cans. To use them, ob- serve the following illustrations. Type C and D—For details, see “Front seat side table” on page 380 in this Sec- tion. Type G—For details, see “Removable con- sole box” on page 375 in this Section.

CAUTION

(cid:2) Do not place anything else other than cups or drink−cans in the cup items may be holder, as such thrown about and possibly injure people in the vehicle during sudden braking or in an accident.

Type A (instrument panel)

reduce

(cid:2) Type A and F—To

the chance of injury in case of an acci- dent or a sudden stop while driv- ing, keep the cup holder closed when it is not in use.

Type B (quarter trim)

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Type C (front side of the front seat side table)

Type E (front side of console box)

Type D (rear side of the front seat side table)

Type F (rear side of console box)

373

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Bottle holders

Type G (console box tray)

Front door

374

Sliding door

The bottle holders are designed to hold bottles securely.

CAUTION

Do not attempt to use the holder for any other purpose for which it was intended. Inappropriately sized or shaped objects may be thrown about in the compartment and possibly in- jure people in the vehicle during a sudden braking or an accident.

NOTICE

Do not put a cup or open bottle in the bottle holder because the con- tents may spill when the door opens or closes.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Storage box

Removable console box

UPPER TRAY To access the upper tray, raise the con- sole box lid.

This box is designed to place things like bottles.

375

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

THE

INSTALLING

REMOVING AND CONSOLE BOX The console box can be removed and installed between the front seats and between the second seats as shown in the illustrations. When the console box is installed in the second seat position, the right side sec- ond seat must be in the outside position.

Between the front seats

CONSOLE BOX To access the console box, pull up the lock release lever and raise the console box lid.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the console box closed while driving.

injury

376

Between the second seats

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

To remove the console box: Open the auxiliary box of the rear side and pull up the lock release lever to disengage the rear lock. Then lift the console box and release the front hook.

07 SIENNA_U (L/O 0612)

To install the console box between the front seats: 1. Install the front hook in the front striker of the console box under− tray.

2. Rotate down straight and push down

to engage the rear lock.

CAUTION

(cid:2) Be careful not to get your hands or

feet pinched in the console box.

(cid:2) Make sure the console box is se- curely locked by pushing forward, rearward, upward and sideways. Failure to do so may cause an un- expected accident or severe injury in the event of emergency braking or a collision.

377

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

To install the console box between the second seats: 1. Install the front hook

in the rear

striker of the double striker set.

The striker is used as both the console box lock striker and the right second seat lock striker when the right second seat is in the inside position. 2. Rotate down straight and push down

to engage the rear lock.

CAUTION