2007 Toyota Sienna Owners Manual

it is secure. Follow all the installation instructions provided by its manufac- turer.

To remove the infant seat: Press the buckle release button and allow the belt to retract completely. The belt will move freely again and be ready to work for an adult or older child passenger.

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat must be used in for- ward−facing or rear−facing position de- pending on the age and size of the the child. When manufacturer’s the applicable age and size of the child as well as directions the child restraint system.

installing, follow instructions about

installing

for

145

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

light

indicator

illuminated when the ignition key

The “AIRBAG OFF” indicator light should be is “ON” and the child is in the child restraint system after following these procedures. The “AIRBAG OFF” indi- cates the SRS front passenger airbag and side airbag on the passenger side will not deploy. If the “AIRBAG ON” indicator light is illuminated, remove the child restraint system and reinstall it with the ignition key in the “ACC” or “LOCK” position. If the “AIRBAG ON” indicator light is illumi- nated when the ignition key is turned to the “ON” position, then the SRS front pas- senger airbag and side airbag on the pas- senger side may deploy in an accident. Do not drive the vehicle in this condition. Remove the child restraint system and contact your Toyota dealer.

6. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

7. Put a child on the child restraint sys- tem and secure the child, complying with the instructions provided by the child restraint system manufacturer.

Install the child restraint system on the front passenger seat only when it is un- avoidable. Your vehicle is equipped with a front passenger occupant classification system. In order to activate the occupant classification system correctly, install the forward−facing child restraint system on the front passenger seat in the following order: 1. Turn the ignition key to the “ON” posi-

tion.

2. Move the front passenger seat to the

rearward position.

3. Put the child restraint system on the front passenger seat without putting your weight on front passenger seat.

the

4. Insert the seat belt tab into the seat

belt buckle.

5. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended. To hold the seat securely, make sure the belt is in the lock mode before letting the belt retract.

146

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

CAUTION

the

(cid:1) Never install a rear−facing child re- straint system on the front passen- ger seat. A forward−facing child re- straint system should only be installed on front passenger seat when unavoidable. If you must install the child restraint system on the front passenger seat, put the seat in its most rearward position, and install the forward−facing child restraint system in the proper or- der. Otherwise, the front passenger occupant classification system can not detect the presence of the child restraint system and the front pas- senger airbag and side airbag on the front passenger seat could deploy, and the impact could cause death or serious injury to the child.

07 SIENNA_U (L/O 0612)

Move seat fully back

(cid:1) Never install a rear−facing child re- straint system on the front passen- ger seat even if the “AIRBAG OFF” indicator light is illuminated. In the event of an accident, the force of the rapid inflation of the front pas- senger airbag could cause death or serious if the rear−facing child restraint system is installed on front passenger seat.

injury to the child

the

the

(cid:1) A forward−facing child restraint sys- tem should be allowed to be installed on front passenger seat only when it is unavoidable. Always move the seat as far back as possible even if the “AIRBAG OFF” indicator light is illuminated, because the front passenger airbag could considerable speed and the child may be killed or seriously in- jured.

force. Otherwise,

inflate with

147

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Same angle

the area of

(cid:1) On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the side window or the seat, front or side pillars or roof side rails from which the side air- bags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dan- gerous the side airbag and/or curtain shield airbag inflate, and the impact could cause death or seri- ous injury to the child.

if

(cid:1) Do not install a child restraint sys- tem on the second (or third) seat if it interferes with the lock mecha- nism of the front (or second) seats. Otherwise, the child or front (or second) seat occupant(s) may be killed or seriously injured in case of sudden braking or a collision.

(cid:1) If the driver’s seat position does not allow sufficient space for safe installation, re- straint system on the second right seat.

the child

install

(cid:1) When

in

the

installing a child restraint system third seat center position, adjust both seatbacks to the same angle. Otherwise, the child restraint system cannot be se- curely this may cause death or serious injuries in a collision.

restrained and

148

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt to retract.

149

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

To install the convertible seat: 1. Run the lap and shoulder belt through or around the convertible seat following instructions the its manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided the insert

by tab

07 SIENNA_U (L/O 0612)

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

To remove the convertible seat: Press the buckle release button and allow the belt to retract completely. The belt will move freely again and be ready to work for an adult or older child passenger.

150

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

CAUTION

(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward−facing position only.

Move seat fully back

the

(cid:1) A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible even if the “AIRBAG OFF” indicator light is illuminated, because the front passenger airbag considerable could speed and the child may be killed or seriously in- jured.

force. Otherwise,

inflate with

the area of

(cid:1) On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the side window or the seat, front or side pillars or roof side rails from which the side air- bags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dan- gerous the side airbag and/or curtain shield airbag inflate, and the impact could cause death or seri- ous injury to the child.

if

151

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Same angle

CAUTION

(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.

(cid:1) When

in

the

installing a child restraint system third seat center position, adjust both seatbacks to the same angle. Otherwise, the child restraint system cannot be se- curely this may cause death or serious injuries in a collision.

restrained and

152

the

instructions provided by

To install the booster seat: Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child fol- lowing its manufacturer and insert the tab into the buckle taking care not to twist the belt. Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips. See “Seat belts” on page 108 in this Section for details.

could

(cid:1) Both high−positioned lap belts and cause loose−fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.

injuries due

(cid:1) For child’s safety, do not place the

shoulder belt under child’s arm.

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

—Using a top strap (for second seats)

(cid:1) If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

To remove the booster seat: Press the buckle release button and allow the belt to retract.

Follow the procedure below for a child restraint system that requires the use of a top strap.

153

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Use the anchor brackets on the back of the second seats to attach the top strap. Anchor brackets are for each second seating position.

installed

Anchor brackets

7−passenger models

Anchor brackets

8−passenger models

154

TO USE THE ANCHOR BRACKET: 1. Remove the head restraint.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

—Using a top strap (for third seats)

3. Replace the head restraint.

Follow the procedure below for a child restraint system that requires the use of a top strap.

2. Fix the child restraint system with

the seat belt. Latch bracket and tighten the top strap.

the hook onto

the anchor

instructions

For the child re- straint system, see “Child restraint” on page 139 in this Section.

install

to

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

155

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Anchor brackets

Use the anchor brackets on the back of the third seats to attach the top strap. Anchor brackets are installed for right and center seating position.

TO USE THE ANCHORAGES: 1. Remove the head restraint.

2. Fix the child restraint system with

the seat belt. Latch bracket and tighten the top strap.

the hook onto

the anchor

instructions

For the child re- straint system, see “Child restraint” on page 139 in this Section.

install

to

156

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

—Installation with child restraint lower anchorages (for second seats)

CAUTION

(cid:1) Do not replace the head restraint when the child restraint system is installed. The head restraint may in- terfere with the top strap and the child restraint system can not be securely restrained. This may cause death or serious injuries in a colli- sion.

(cid:1) Make sure the top strap is securely latched, and check that the child restraint system is secure by push- ing and pulling it in different direc- tions. Follow all the installation in- structions provided by its manufac- turer.

7−passenger models

8−passenger models

The lower anchorages for the child re- straint systems complying with the FMVSS225 or CMVSS210.2 specifica- tions are installed in the rear seat. The anchorages are installed in the seat cushion of each second seat. Child restraint systems complying with the FMVSS213 or CMVSS213 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

157

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

5th lock position

1st lock position

SYSTEM

RESTRAINT

CHILD INSTALLATION 1. Fold down the seatback. The rear legs will disengage. Pushing seat downward on the back of the seat, make sure the rear seat legs are re- locked into place. Next pull back the seatback lock position (the most upright position). Then ad- just the seatback to the 5th lock position. Make sure locked securely.

the seat and seatback are

the 1st

to

158

Canada only

Canada only

Type A

Type B

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

2. Turn up the covers for the lower an- chorages. Confirm the position of the lower anchorages near the but- ton in the seat cushion.

3. Type A—Latch the hooks of

lower the anchorages and

straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.

For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap (for second seats)” on page 153 in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.

it should be anchored. (For

07 SIENNA_U (L/O 0612)

—Installation with child restraint lower anchorages (for third seats)

CAUTION

(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

(cid:1) When using the lower anchorages for the child restraint system, en- sure that the seat is moved to the rear−most position, with the seat- back close to the child restraint system.

(cid:1) After securing

the child restraint system, never slide or recline the seat.

(cid:1) Do not install a child restraint sys- tem on the second seat if it inter- feres with the lock mechanism of the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sudden braking or a collision.

The lower anchorages for the child re- straint systems complying with the FMVSS225 or CMVSS210.2 specifica- tions are installed in the rear seat. The anchorages are installed in the clear- ance between the seat cushion and seat- back of the right and center seats. Child restraint systems complying with the FMVSS213 or CMVSS213 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

159

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

RESTRAINT

CHILD INSTALLATION 1. Manual seat—Fold down

SYSTEM

the seat- back and pull back to the 1st lock position (the most upright position) until it locks into place. Adjust the seatback to the 11th lock position. Make sure the seatback is locked se- curely. Power seat—Fold down the seatback by pressing folding/returning switch. Raise the seatback by press- ing the same switch, the returning switch or the seatback adjusting switch. (The seat back will automati- cally stop.) For details of these switch operations, see page 98. Do not touch the switch while the seat- back is moving, because the operation will stop.

the

Canada only

Type A

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

1st lock position

11th lock position

Manual seat

Power seat

160

07 SIENNA_U (L/O 0612)

2. Widen

the gap between

the seat cushion and seatback slightly and confirm the position of the lower an- chorages near the seatback.

the button on

3. Type A—Latch the hooks of

lower the anchorages and

straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.

For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap (for third seats)” on page 155
in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.

it should be anchored. (For

Canada only

Type B

CAUTION

(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

(cid:1) After securing

the child restraint

system, never recline the seat.

(cid:1) Do not put a child restraint system on the third seat if it interferes with the lock mechanism of the second seats. Otherwise, the child or front (or second) seat occupant(s) may be killed or seriously in case of sudden braking or a colli- sion.

injured

161

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

162

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

SECTION 1− 4

OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt and telescopic steering wheel Outside rear view mirrors Anti−glare inside rear view mirror Auto anti−glare inside rear view mirror Vanity mirrors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

164
164
167
167
168

163

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Tilt and telescopic steering wheel

Outside rear view mirrors—

CAUTION

(cid:1) Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.

(cid:1) After adjusting the steering wheel, try moving it up and down or for- ward and rearward to make sure it is locked in position.

To adjust the steering wheel position, push down the lock release lever. Then tilt the steering wheel to the desired angle, push or pull it to the desired steering column length and pull up the lock release lever.

164

Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side because it is a convex mirror. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

—Power rear view mirror control

in “AUTO” mode,

Vehicles with the auto anti−glare inside rear view mirror—On some models, when the inside rear view mirror surface dark- ens the outside rear view mirror surface also darkens to re- duce the reflection of the headlights of the vehicle behind you. (For details, see “Auto anti−glare inside rear view mirror” on page 167 in this Section.) On some models, when you push the rear window defogger switch, the heater panels in the outside rear view mirrors will quick- ly clear the mirror surface. (See “Rear window and outside rear view mirror de- foggers and windshield wiper de−icer” on page 184 in Section 1−5.)

CAUTION

(cid:1) Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.

(cid:1) On some models, since the mirror surfaces can get hot, do not touch them when the defogger switch is on.

Type A

Type B

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Push (right).

the switch to “L” (left) or “R”

2. Control switch—To move the mirror

Push the switch in the desired direc- tion.

Mirrors can be adjusted when the key is in the “ACC” or “ON” position. Vehicles with the driving position memory system—The position of the outside rear view mirrors and driver’s seat can be memorized. For details, see “Driving posi- tion memory system” on page 65 in Sec- tion 1−3.

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror.

165

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

—Folding rear view mirrors

Type A

166

Type B

07 SIENNA_U (L/O 0612)

The rear view mirrors can be folded backward for parking in compact areas. Type B only—Mirror can be folded when key is in the “ACC” or “ON” position. Position 1—To fold the mirrors. Position 2—To return the mirrors back to their original positions. The rear view mirrors can be also folded by pushing backward.

CAUTION

(cid:1) To avoid personal

mirror malfunction, do not the mirror while it is moving.

injury and any touch

(cid:1) Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Anti−glare inside rear view mirror

Auto anti−glare inside rear view mirror

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. This mirror is equipped with auto anti− glare function. The function is designed to reduce glare from the headlights of the vehicle behind you during night driving. When inserted and turned on, the inside rear view mirror al- ways turns on in the automatic function mode. The indicator illuminates to show you that the function is on.

ignition key

the

is

167

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Vanity mirrors

to reduce

In automatic function mode, if the mirror detects light from the headlights of the the mirror surface vehicle behind you, darkens slightly the reflected light. To turn off and on the automatic function, push the switch. Adjust it before driving so that the rear view is in the best condition. When the inside air temperature is low, it may take a little longer for the mirror to darken the detection of headlights.

in response

to

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

To ensure correct functioning of anti− glare mirror sensors located on both sides of the mirror, do not touch or cover the sensors with your finger or a piece of cloth, etc.

To use the vanity mirrors, swing down the sun visor and open the cover. On vehicles with the vanity lights, the light will come on when you open the cover. VANITY LIGHTS CUT OFF OPERATION When the ignition switch is turned off and vanity light stays lighting on, the light will cut off automatically after 20 minutes.

168

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

You can cancel the cut off operation by: (cid:1) Turning the key to the “ACC” position. (cid:1) Opening or closing any of front and

sliding doors.

(cid:1) Turning off all the “ON” lights. All the lights are cut off when all the side doors and back door are locked by key or wireless remote control transmitter. The ignition switch must be turned off.

169

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

170

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

SECTION 1− 5

OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Headlight beam level control Emergency flashers Instrument panel light control Front fog lights Front personal lights Rear personal lights Luggage compartment light Ignition switch light Exterior foot lights Windshield wipers and washer Rear window wiper and washer Rear window and outside rear view mirror defoggers and windshield

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

172
176
177
178
178
179
180
181
181
182
183
184

wiper de−icer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

184

171

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Headlights and turn signals (without automatic light control system)

the

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights On some models— For Canada—The tail light indicator lights up in the instrument cluster. Position 2—Headlights and all of above On some models— For lights up in the instrument cluster. Automatic light cut off system Position 1— The lights automatically turn off when the driver’s door is opened with the ignition key in the “ACC” or “LOCK” position. Position 2— The lights automatically turn off after 30
seconds when all the side doors and back door are closed with the ignition key in the “ACC” or “LOCK” position.

the U.S.A.—The headlight

indicator

lights automatically

time before the headlights

If the lock switch of the wireless remote control transmitter is pushed when all the side doors and back door are already locked, turn off the immediately. The turn off can be changed. For details, contact your Toyota dealer. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

For the U.S.A.

For Canada

172

Daytime Running Light (DRL) system (all models sold in Canada and some models sold in U.S.A.) The Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many differ- ent driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. The DRL system will make the headlights come on when: (cid:1) The ignition is on with the engine run-

ning.

(cid:1) The knob is in the “OFF” position or

position 1.

(cid:1) The parking brake is released. To turn off the DRL system, twist the knob to position 2 or turn the ignition switch off.

07 SIENNA_U (L/O 0612)

High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.

173

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Headlights and turn signals (with automatic light control system)

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights On some models— For Canada—The tail light indicator lights up in the instrument cluster. Position 2—Headlights and all of above On some models— For lights up in the instrument cluster. Position 3 (“AUTO”)—Headlights and/or all of the lights in position 1
They automatically turn on or off depend- ing on the darkness of the surroundings. Manually twist the knob to the position 2
to turn on the headlights if they are need- ed immediately when entering a dark tun- nel, parking structure, etc.

the U.S.A.—The headlight

indicator

the

top of

the driver’s side

The automatic light control sensor is on the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor. If you feel that the automatic light control comes into operation too early or too late, have the sensor adjusted by your Toyota dealer. Automatic light cut off system Position 1 or position 3 with the tail lights on— The lights automatically turn off when the driver’s door is opened with the ignition key in the “ACC” or “LOCK” position.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

For the U.S.A.

For Canada

174

07 SIENNA_U (L/O 0612)

lights automatically

Position 2 or 3 with the headlights on— The lights automatically turn off after 30
seconds when all the side doors and back door are closed with the ignition key in the “ACC” or “LOCK” position. If the lock switch of the wireless remote control transmitter is pushed when all the side doors and back door are already locked, turn off the immediately. The turn off can be changed. For details, contact your Toyota dealer. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.

time before the headlights

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

Daytime Running Light (DRL) system (all models sold in Canada and some models sold in U.S.A.) The Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The DRL system can be helpful in many differ- ent driving conditions, but they can be especially helpful in the short periods after dawn and before sunset. The DRL system will make the headlights come on when: (cid:1) The ignition is on with the engine run-

ning.

is

(cid:1) The knob

“OFF” position, position 1 or position 3 with the tail lights on.

the

in

(cid:1) The parking brake is released. To turn off the DRL system, twist the knob to position 2 or position 3 with the head- lights on, or turn the ignition switch off.

High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

175

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Headlight beam level control

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.

176

To adjust the headlight beam level, turn the dial. The following list shows examples of prop- er dial settings. For loading conditions oth- er than those listed, adjust the dial posi- tion so that the beam level is the same as the one obtained according to the list when only the driver is in the vehicle. The higher the number of the dial position, the lower the headlight beam level. Always keep the headlight beam at the proper level, or your headlights may dazzle other road users.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Emergency flashers

Loading condition and dial position

Loading conditions

Variations

7−passenger

models

8−passenger

models

Driver only, or Driver + one passenger in the front seat

Driver + one passenger in the front seat and all passengers in the second seat

All passengers

All passengers + full luggage loading to the luggage compartment

Driver + full luggage loading to the luggage compartment

flashers,

turn on

the emergency

To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.

177

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Instrument panel light control

Front fog lights

NOTICE

To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.

To adjust the brightness of the instru- ment panel lights, turn the knob. On some models, with the knob turned fully clockwise, the intensity of the instru- ment panel lights will not be reduced even when the tail lights/headlights are turned on.

To turn on the front fog lights, twist the band of the headlight and turn sig- nal switch lever. They will come on only when the headlights are on low beam.

178

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Front personal lights

To turn on the front personal lights, operate the personal light main switch. The lights can be turned on or off by pushing each lens when the personal light main switch is in the “DOOR” or “OFF” position. The personal light main switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—The lights can be turned on or off by pushing each lens. “DOOR”—Turns the light on when any of the side doors or back door is opened.

Personal light main switch

ILLUMINATED ENTRY SYSTEM Door linked operation—When the switch is in the “DOOR” position and any of the side doors or back door is opened, the light will come on. After all the side doors and back door are closed, the light re- mains on for about 15 seconds before fading out. Ignition switch linked operation—When the switch is in the “DOOR” position, and the ignition switch is turned to “LOCK”, the light will come on. The light remains on for about 15 seconds before fading out. When any of the side doors and back door is unlocked using either the key or the wireless remote control transmitter, the light will come on and remain on for about 15 seconds before fading out. However, in the following cases, the light goes off immediately. (cid:1) All the side doors and back door are closed when the ignition key is in the “ACC” or “ON” position.

(cid:1) All the side doors and back door are

closed and locked.

179

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Rear personal lights

The following adjustments can be made in this system. For details, contact your Toyota dealer. (cid:1) Cancelling the door key or the wireless remote control transmitter linked opera- tion

(cid:1) Cancelling the ignition switch linked op-

eration.

(cid:1) Changing the duration of lighting To prevent the battery being discharged, the lights will automatically turn off when the key is removed and the door is left opened with the switch at the “DOOR” position for 20 minutes or more.

180

Personal light main switch

is

To turn on the rear personal lights, op- erate the personal light main switch. The lights can be turned on or off by pushing each lens when the personal light main switch in the “DOOR” position. The personal light main switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when any of the sliding doors or back door is opened. To prevent the battery being discharged, the lights will automatically turn off when the key is removed and the door is left opened with the switch at the “DOOR” position for 20 minutes or more.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Luggage compartment light

Ignition switch light

luggage compartment To turn on the light, push luggage compartment the light switch upwards. The light turn on when the personal light main switch is in the “ON” or “DOOR” position. The personal light main switch has the following positions: “ON”—The light turns on when the lug- gage compartment switch is pushed up- wards. “OFF”—Turns the light off. “DOOR”—Turns the light on when the lug- gage compartment switch is pushed up- wards and any of the sliding door or back door is opened. The light goes off when both the sliding doors and back door are closed. To prevent the battery being discharged, the lights will automatically turn off when the key is removed and the door is left opened with the switch at the “DOOR” position for 20 minutes or more.

For easy access to the ignition switch, the ignition switch light comes on when any of the side doors and back door is opened or when the ignition switch is turned to the “LOCK” position. The light remains on for about 15 seconds after all the side doors and back door are closed. However, in the following cases, the light goes off immediately. (cid:1) All the side doors and back door are closed when the ignition key is in the “ACC” or “ON” position.

(cid:1) All the side doors and back door are

closed and locked.

181

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

Personal light main switch

07 SIENNA_U (L/O 0612)

Exterior foot lights

(cid:1) The doors are locked via the driver’s

door key cylinder.

(cid:1) The doors are locked via the switches either inside the driver’s or front pas- senger’s door.

transmitter,

remote control

When any of the side doors or back door is unlocked using either the key or the wireless the light will come on and remain on for about 15 seconds before fading out. The following adjustments can be made in this system. For details, contact your Toyota dealer. (cid:1) Cancelling the door key or the wireless remote control transmitter linked opera- tion

(cid:1) Changing the duration of lighting To prevent the battery being discharged, the light will automatically turn off when the key is removed and the door is left opened for 20 minutes or more.

182

light will come on when

The the side doors and back door are unlocked simulta- neously using either the key or the wire- less remote control. This light remains on for 15 seconds before fading out when any door is opened, and additional 15
seconds after all the side doors and back door are closed. However, in the following cases, the light goes off immediately. (cid:1) Doors are locked with wireless remote

control.

(cid:1) The selector lever is put in a position other than “P” with the ignition switch on.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Windshield wipers and washer

To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Position 3

Intermittent

Slow

Fast

For a single sweep of push the lever up and release it.

the windshield,

the band upward

With interval adjuster: The band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist to increase the time between sweeps, and downward to decrease it. To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” on page 503 in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield is dry. It may scratch the glass.

When waxing your vehicle, make sure that the washer nozzles do not become blocked. If a nozzle becomes blocked, contact your Toyota dealer to have the vehicle serviced.

NOTICE

If a nozzle becomes blocked, do not try to clear it with a pin or other object. The nozzle will be damaged.

183

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Rear window wiper and washer

Rear window and outside rear view mirror defoggers and windshield wiper de−icer

NOTICE

(cid:1) Do not operate the rear wiper if the rear window is dry. It may scratch the glass.

(cid:1) Do not lift the rear wiper arm away from the window, as it may break.

To turn on the rear window wiper, twist the lever knob upward. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Intermittent

Normal

To squirt washer fluid on the rear window, twist the knob upward or downward as far as it will go (position 3 or 4). The knob automatically returns from these positions after you release it. The rear window wip- er operates while the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” on page 503 in Section 7−3. 184

To defog or defrost the rear window, push the switch. The key must be in the “ON” position. The thin heater wires on the inside of the rear window will quickly clear the window surfaces. An indicator light will illuminate to indicate the defogger is operating. the rear view mirror On some models, defoggers and/or the windshield wiper de− icer is also operating simultaneously by this switch. Vehicles with the outside rear view mirror defoggers, the heater panel in the outside rear view mirrors will quickly clear the surfaces. Vehicles with the wind- shield wiper de−icer, the windshield wiper blades will be de−iced.

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

NOTICE

When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.

Push the switch once again to turn the defoggers off. The system will automatically shut off af- ter the defoggers have operated about 15
minutes.

CAUTION

Vehicles with outside rear view mirror defoggers, since the mirror surfaces can get hot, do not touch them when the defogger switch is on.

turn

Make sure you the defoggers off when the surfaces are clear or the wiper blades have de−iced. Leaving the defog- gers on for a long time could cause the battery to discharge, especially during stop−and−go driving. The defoggers are not designed for drying rain water or for melting snow. If the outside rear view mirrors are heavi- ly coated with ice, use a spray de−icer before operating the switch.

185

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

186

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

SECTION 1− 6

OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel gauge Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer Odometer and two trip meters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzers

188
188
189
190
191

187

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

Fuel gauge

Low fuel level warning light

Type A

Low fuel level warning light

Type B

188

07 SIENNA_U (L/O 0612)

Engine coolant temperature gauge

indicates

The gauge the approximate quantity of fuel remaining in the tank when the ignition switch is on. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. The needle moves when braking, acceler- ating or making turns. This is caused by the movement of the fuel in the tank. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.

Type A

Type B

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Tachometer

The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: (cid:1) Driving up a long hill on a hot day. (cid:1) Reducing speed or stopping after high

speed driving.

(cid:1) Idling for a long period with the air conditioning on in stop−and−go traffic.

(cid:1) Towing a trailer.

NOTICE

(cid:1) Do not remove the thermostat in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.

(cid:1) Do not continue driving with an overheated engine. See “If your ve- hicle overheats” on page 436 in Section 4.

The tachometer indicates engine speed in thousands of rpm (revolutions per minute). Use it while driving to select correct shift points and to prevent en- gine lugging and over−revving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.

NOTICE

Do not let the indicator needle get into the red zone. This may cause severe engine damage.

189

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Odometer and two trip meters

This meter displays the odometer and two trip meters. 1. Odometer—It shows the total distance

the vehicle has been driven.

3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter then back B, the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.

to

2. Two

trip meters—Show

two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.

fuel economy and

the other

190

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

Service reminder indicators and warning buzzers

If the indicator or buzzer comes on...

Do this.

(a)

(b)

(c)

(d)

(e)

(f)

(g)

or

If parking brake is off, stop immediately and contact Toyota dealer.

(indicator and buzzer)

Fasten driver’s seat belt.

Fasten front passenger’s seat belt.

Stop immediately and contact Toyota dealer.

or

Take vehicle to Toyota dealer.

Low fuel level warning light

Fill up tank.

Stop and check.

191

2007 SIENNA from Oct. ’06 Prod. (OM45437U)

07 SIENNA_U (L/O 0612)

If the indicator or buzzer comes on...

Do this.

(h)

(i)

(j)

(k)

(l)

(m)

(n)

192