2004 Toyota Sienna Owners Manual

04 SIENNA_U (L/O 0408)

CAUTION

D Do not drive with using the head- phone. Otherwise, you may be hard to hear the sound from the outside while using the headphone and may cause an accident.

D With DVD player:

that

Conversational speech on some DVDs is recorded at a low volume to emphasize the impact of sound effects. If you adjust the volume assuming the conversations represent the maximum volume lev- el that the DVD will play, you may be startled by louder sound effects or when you change to a different audio source. Be sure to adjust the volume with this in mind. Make sure the volume creased, before you headphone.

is not turn on

in- the

233

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

The rear seat audio system consists of following components. 1. Volume control knobs 2. Rear seat audio system display 3. Headphone input jacks 4. Front audio system 5. Rear seat audio system controller

—Rear seat audio system controller The rear seat audio system can be oper- ated with the rear seat audio system con- troller.

CAUTION

Do not disassemble or modify the controller. It may cause an accident, fire or electric shock.

NOTICE

Keep the controller away from direct sunlight, high heat and high humidity. These conditions could cause the case to deform or the battery to ex- plode or leak.

234

BEFORE USING THE CONTROLLER (for new vehicle owners) A battery is already set in the control- ler with an insulating sheet, which pre- from being dis- vents charged. Before using the controller, remove the insulating sheet.

the battery

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

USING THE CONTROLLER To use the rear seat audio system con- troller, direct the signal output portion of the controller to the signal reception portion of the rear seat audio system display. The rear seat audio system controller can be operated when the ignition switch is in the “ACC” or “ON” position. The controller does not operate properly when the signal reception portion of the display to direct sunlight. Block the display from direct sunlight. Details of specific buttons, controls, and features see “CONTROLLER FEATURES” on page 236
in this Section.

is exposed

controller,

the

of

CAUTION

To reduce the chance of in case of an accident or a sudden stop while driving, stow the controller in the console box or front seat side table when it is not in use.

injury

NOTICE

Observe the followings, otherwise the controller may be damaged. z Do not drop or strongly knock the

controller against hard objects.

z Do not sit on or place heavy ob-

jects on the controller.

z Do not leave the controller exposed to high temperatures (such as on the long time.

instrument panel) for a

235

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

” and “ ” and “

CONTROLLER FEATURES 1. “ 2. “ 3. “ON/SOURCE” button 4. “OFF” button

” (DISC/CH/PROG) buttons ” (TUNE/TRACK) buttons

1. “

” and “

” (DISC/CH/PROG) but-

tons

the “

” or “

Radio You can scan only the preset stations for the band of the front audio system. (For instructions, see “—Controls and features” on page 215 in this Section.) To scan the preset stations: ” (DISC/CH/PROG) Push button. The radio will tune in the next preset station up or down the band. The station frequency will appear on the dis- play. Cassette tape player Push ” (DISC/CH/PROG) ” or “ button to select the other side of a cas- sette indicates which ” indicates side is currently selected. (“ indicates the bottom the side.) the cassette Auto−reverse player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

tape. The display

feature: After

top side, “

the “

”

236

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

” or “

” or “

” and “

” (TUNE/TRACK) but-

Compact disc player Compact disc changer only— Use this button to select a disc you want to listen to. ” (DISC/CH/PROG) Push the “ button until the number of the disc you want to listen to appears on the display. 2. “ ” (TUNE/TRACK) buttons Radio Push the “ ton to tune or seek. Tuning: ” or “ ” Quickly push and release the “ (TUNE/TRACK) button. Each time you push the button, the radio will step up or down to another frequency. If you push and hold the button, and the radio will go into the seek mode. Seeking: ” (TUNE/ Push and hold the “ TRACK) button. The radio will seek up or down for a station of the nearest frequen- cy and will stop on reception. Each time you push the button, the stations will be searched one after another.

” or “

”

the “

” (TUNE/TRACK) button.

Cassette tape player This button has the following features— To fast forward or reverse: ” (TUNE/TRACK) Push and hold button until “FF” will appears on the dis- play to forward a tape. Push and hold the (TUNE/TRACK) button until “REW” “ appears on the display to rewind a tape. To stop the tape while it is fast forward- ” (TUNE/TRACK) button. To ing, push “ stop the tape while it is rewinding, push “ If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast forwards completely, the cassette will play the other side of the tape using the auto−reverse feature. To skip up or down to locate a song or recording. You can select up to nine recordings (in- cluding current one). ” (TUNE/TRACK) but- Push the “ ton. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button 10 times, the skip feature will be turned off.

” or “

For the skip feature to work correctly a blank space of at least 3 seconds is con- sidered to be a start of a recording. When a beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken, live, or classical re- cordings. Compact disc player This button has the following features— To skip up or down to a different track: ” (TUNE/TRACK) but- Push the “ ton until the number of the track you want to listen to appears on the display. If you the want current track, quickly push ” (TUNE/TRACK) button one time. To fast forward or reverse: ” (TUNE/ Push and hold the “ TRACK) button to fast forward or reverse within a compact disc. When you release the button, the compact disc player will resume playing.

the beginning of

to return to

” or “

” or “

the

“

237

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

3. “ON/SOURCE” button Push “ON/SOURCE” button to turn on the rear seat audio system. Use “ON/SOURCE” button to select an audio mode when the rear seat audio sys- tem is on. Each time you push this but- ton, the system changes between the ra- dio, cassette player and compact disc player. When you change the mode, the display indicates which mode is selected. When a cassette tape and compact discs are not loaded in the front audio system, only a radio mode can be selected in the rear seat audio system. If you push “ON/SOURCE” button to se- lect the casette tape player mode or com- pact disc player mode in that case, a beep sounds from front audio system and “INVALID” for 6
seconds, and then the rear audio system returns to the radio mode. If you push “ON/SOURCE” button while receiving an emergency broadcast, a beep sounds and the screen to indicate that no button can be operated.

“INVALID” appears on

the screen

flashes on

Radio AM mode When you select the AM mode, “AM” will appear on the screen. FM mode When you select the FM mode, “FM1” or “FM2” will appear on the display. If the front audio system receives a traffic the rear seat announcement (TA) while audio system the radio mode, “TRAF” will flash on the screen and the rear seat audio system will turn off. When the traffic an- nouncement (TA), the rear seat audio sys- tem cannot select the AM/FM mode. Tape mode “TAPE” appears on the screen while this mode is selected.

front audio

receives a

in

is

the screen while this

Compact disc mode “CD” appears on mode is selected. The screen shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will screen one of the four following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERR 1”: The disc may be dirty, damaged or (up−side down). Clean the disc and re−insert it. “ERR 3”: There is a problem inside the system. Eject the disc. Set the disc again. “ERR 4”: Over−current. Ask your Toyota dealer to inspect. If the malfunction still exists, take your vehicle to your Toyota dealer. 4. “OFF” button Push “OFF” button to turn off seat audio system.

incorrectly

the rear

inserted

238

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

REPLACING CONTROLLER BATTERY For replacement, use a CR2025 lithium battery or equivalent.

CAUTION

Special care should be that small children do not swallow the re- moved battery or components.

taken

NOTICE

z When replacing the battery, be care-

ful not to lose the components.

z Replace only with

the same or equivalent type of battery recom- mended by a Toyota dealer.

z Dispose of used batteries according

to the local regulations.

Replace the battery by using the following procedures: 1. Pull

the case out while pushing

the

lock release button to the side.

2. Remove the discharged battery. 3. Put in a new battery with the positive

(+) side up. Put in the case securely.

NOTICE

z Make sure that the positive side of the controller battery is facing cor- rectly.

z Do not replace the battery with wet

hands. Water may cause rust.

z Do not touch or move any compo- nents inside of the controller, or it may interfere with proper operation.

239

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

—Headphone input jacks

z Be careful not to bend the electrode of the controller battery insertion and that dust or oil does not ad- here to the transmitter case.

z Close the battery case securely.

After replacing the battery, check that the controller operates properly. If the control- ler still does not operate properly, contact your Toyota dealer.

You can enjoy the rear seat audio sys- tem with commercial headphone. To use the headphones, connect them to the jack. The key must be in the “ACC” or “ON” position.

To adjust the volume of the headphones, turn the knob. Turn right to increase the volume. Turn left to decrease the volume. The maximum volume depends on the type of headphones. The recommended headphone impedance is from 16 Ω to 32 Ω. Please contact your Toyota dealer for fur- ther details.

CAUTION

240

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

Adjust the volume when you connect the headphones jack. Loud sounds may have a significant impact on the human body.

the

to

04 SIENNA_U (L/O 0408)

Rear seat entertainment system—

The rear seat entertainment system con- sists of the following components. 1. Rear seat entertainment system display 2. Headphone input jacks 3. Headphone volume control dials 4. Front audio system 5. Power outlet main switch 6. Power outlets 7. Input terminal adapter 8. Rear seat entertainment system

controller

241

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

The rear seat entertainment system is de- signed for the rear passengers to enjoy audio and DVD video separately from the front audio system. The rear seat entertainment system can be operated when the ignition key is in the “ACC” or “ON” position. The rear passengers can enjoy all modes (AM and FM radio, cassette tape player, compact disc player with changer and DVD player) on the rear seat entertain- ment system only if a cassette tape and a compact disc are loaded in the front audio system. The rear seat entertainment system can play DVD video, audio CD, video CD, CD text, dts−CD or DVD audio only when a disc is loaded in the DVD player. You can enjoy videos and sound when your personal audio system is connected to the input terminal adapter. For details, refer to the manufacturer’s instructions.

You can enjoy the rear seat entertainment system with commercial headphone. See “—Headphone input jacks” on page 291 in this Section for details. You can also enjoy the rear seat enter- tainment system with a wireless head- phone. The wireless headphone can be used within rear seat. If the signal be- the headphone will mute. comes weak, For details, refer the manufacturer’s instructions. With some wireless headphone generally available in the market, it may be difficult to catch sound properly. Toyota recom- mends the use of Toyota genuine wireless headphone. You can purchase a wireless headphone at a Toyota dealer.

to

CAUTION

D Do not drive with using the head- phone. Otherwise, you may be hard to hear the sound from the outside while using the headphone and may cause an accident.

D With DVD player:

that

Conversational speech on some DVDs is recorded at a low volume to emphasize the impact of sound effects. If you adjust the volume assuming the conversations represent the maximum volume lev- el that the DVD will play, you may be startled by louder sound effects or when you change to a different audio source. Be sure to adjust the volume with this in mind. Make sure the volume creased, before you headphone.

is not turn on

in- the

242

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

—Display

To open the display, push the lock release button.

Push down the display until it is locked.

NOTICE

The screen should be cleaned with a dry soft cloth. If the screen is pushed by hand or wiped with a hard cloth, the surface of the screen may be scratched.

To close, push up the display until you hear a click. The illumination of the screen is automati- cally is closed. However, the rear seat entertain- ment system is not turned off.

turned off when

the display

CAUTION

To reduce the chance of in case of an accident or sudden stop while driving, close the display when it is not in use.

injury

243

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

NOTICE

z Benzene or alkaline solutions may damage the coated surface of the screen.

z To prevent the battery from being discharged, do not turn on the rear seat entertainment system longer than necessary when the engine is not running.

—Rear seat entertainment system controller The rear seat entertainment system can be operated with the rear seat entertain- ment system controller and buttons on the DVD player unit. The system cannot be operated by touching the switches on the screen directly.

CAUTION

Do not disassemble or modify the controller. It may cause an accident, fire or electric shock.

NOTICE

Keep the controller away from direct sunlight, high heat and high humidity. These conditions could cause the case to deform or the battery to ex- plode or leak.

BEFORE USING THE CONTROLLER (for new vehicle owners) A battery is already set in the control- ler with an insulating sheet, which pre- from being dis- vents charged. Before using the controller, remove the insulating sheet according to the following procedure.

the battery

244

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

1. Remove the cover of the controller

as shown.

2. Remove the insulating sheet.

245

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

USING THE CONTROLLER To use the rear seat entertainment sys- tem controller, direct the signal output portion of the controller to the signal reception portion of the rear seat enter- tainment system display. The controller does not operate properly when the signal reception portion of the display to direct sunlight. Block the display from direct sunlight.

is exposed

CAUTION

To reduce the chance of in case of an accident or a sudden stop while driving, stow the controller in the console box or front seat side table when it is not in use.

injury

NOTICE

Observe the followings, otherwise the controller may be damaged. z Do not drop or strongly knock the

controller against hard objects.

z Do not sit on or place heavy ob-

jects on the controller.

z Do not leave the controller exposed to high temperatures (such as on the long time.

instrument panel) for a

246

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

FCC Information

in construction of

Caution: Any changes or modifica- tions this device which are not expressly approved by the party responsible for compliance could void the user’s authority to op- erate the equipment.

FCC Label Information

the

following

This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, In- cluding interference that may cause undesired operation.

LOCATING THE CONTROLLER If you lose sight of the controller, push and hold the “CURSOR (REMOTE)” button on the DVD player unit until you hear a beep. A buzzer sounds from the controller to let you know where it is. To stop the buzzer, push any button of the controller. If the controller is located close to some- thing that blocks the signal, such as some kind of metal, the controller may not re- ceive the signal and the buzzer may not sound.

247

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

—Control buttons "Controller

248

04 SIENNA_U (L/O 0408)

1. “DVD” button

This button turns on the DVD mode.

2. “SOURCE” button

This button turns on the rear seat en- tertainment system and selects the mode.

3. “OFF” button

This button turns off the rear seat en- tertainment system.

4. Joy stick

This joy stick selects a control switch, mode switch on the menu for the disc.

the screen or

5. “ENT” button

This button inputs the selected switch or the selected menu for the disc.

6. “DISC/CH/PROG” button

This button skips directly to a desired preset station, disc, track or chapter.

7. “""” button This button when the DVD player is operated.

fast

forwards a screen

8. “RETURN” button

This button skips to the predetermined scene for the disc.

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

9. “MENU” button

16. “TOP MENU” button

This button indicates the menu screen for DVD video when the DVD player is operated.

This button indicates the title selection screen for DVD video when the DVD player is operated.

10. “AUDIO” button

17. “

” button

This button indicates the changing au- dio screen when is operated.

the DVD player

11. “SUB TITLE” button

This button indicates the changing sub- title screen when the DVD player is operated.

12. “DISPLAY” button

This button adjusts tone, contrast and brightness of the screen.

the color,

13. “SET UP” button

This button indicates the initial set up screen when the DVD player is oper- ated.

14. “ANGLE” button

This button selects the angle of the screen when the DVD player is oper- ated.

15. “SEARCH” button

This button indicates the title search screen when the DVD player is oper- ated.

This button pauses a screen when the DVD player is operated.

18. “AA” button

This button reverse a screen when the DVD player is operated.

19. “"” button

This button plays a screen when the DVD player is operated.

20. “TUNE/TRACK” button This button operates system or select when the DVD player is operated.

front audio track/chapter

the

the

21. “CURSOR” button

button

This control switches on the screen when the DVD player is operated.

indicates

the

22. “VIDEO” button

This button turns on the video mode when your personal audio device is connected.

249

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

"Buttons on the DVD player unit

04 SIENNA_U (L/O 0408)

1. “

” button

This button ejects a disc.

2. “SOURCE” button

This button turns on the rear seat en- tertainment system and selects the mode.

3. “TUNE/TRACK” button This button operates system or select when the DVD player is operated.

front audio track/chapter

the

the

4. “DISC/CH/PROG” button

This button skips directly to a desired preset station, disc, track or chapter.

5. “CURSOR (REMOTE)” button

the

button

indicates

control This switches on the screen when the DVD player is operated. This button also can be used when you lose sight of the controller.

250

6. Joy stick

This joy stick selects a control switch, mode switch on the menu for the disc.

the screen or

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

—Turning the rear seat entertainment system on and off

7. “ENT” button

This button inputs the selected switch or the selected menu for the disc.

8. “DISC” indicator light indicates

light

This loaded.

that

the disc

is

Controller

DVD player unit

the

turn on

the system, push

To “SOURCE” button. The screen indicates which mode can be selected. Push the “DVD” or “VIDEO” but- ton when the connected DVD player or your personal audio machine is on. The rear seat entertainment system will be turned on. The rear seat entertainment system can select all the modes. When a cassette tape, a compact disc, a DVD video disc, an audio CD, a video CD, a CD text, a dts−CD or a DVD audio disc is not loaded on the front audio sys- tem or the radio mode can be selected on the rear seat entertainment system.

the DVD player, only

251

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

—Front audio system operation All the modes of the front audio system can be operated on the rear seat enter- tainment system. When the same mode is selected on the front and rear audio systems simulta- neously, the system can be operated on the front audio system. If the radio mode is selected on the front and rear audio systems at the same time, AM and FM modes cannot be changed on the rear seat audio system.

To turn off the system, push the “OFF” button. When the front audio system is turned off, the rear audio system and the DVD player will be turned off simultaneously.

252

Controller

DVD player unit

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

SELECTING THE MODE Use the mode. Push the “ENT” button to enter the mode.

to select

joy stick

the

04 SIENNA_U (L/O 0408)

Cassette tape player and compact disc player

The mode display which is selected by the joy stick is colored blue. When the “ENT” button is pushed, the mode display changes to green. If the mode display is gray, it cannot be selected. The “Speaker sound” on the mode display is selected on the front audio system.

Radio

253

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

When you select a mode, the screen indi- cates which is selected. Radio AM mode: When you select the AM mode, “AM” will appear on the screen. FM mode: When you select the FM mode, “FM1” or “FM2” will appear on the screen. Tape mode “TAPE” appears on the screen while this mode is selected. Compact disc mode “CD” appears on mode is selected. The screen shows the track, or track and disc number currently being played.

the screen while this

Controller

254

DVD player unit

04 SIENNA_U (L/O 0408)

OPERATING FRONT AUDIO SYSTEM To operate the front audio system, use the following switches. 1. “DISC/CH/PROG” button Radio You can scan only the preset stations for the band of the front audio system. (For instructions, see “—Controls and features” on page 215 in this Section.) To scan the preset stations: ” side of the “DISC/ Push the “ CH/PROG” button. The radio will tune in the next preset station up or down the band. The station frequency will appear on the screen.

” or “

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

” or “

Cassette tape player Push the “ ” side of the “DISC/ CH/PROG” button to select the other side of a cassette tape. The screen indicates ” indi- which side is currently selected. (“ ” indicates the bot- cates the top side, “ tom side.) Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

feature: After

04 SIENNA_U (L/O 0408)

” or “

” or “

” side of the “TUNE/

2. “TUNE/TRACK” button Radio Push the “ TRACK” button to tune or seek. Tuning: Quickly push and release the “ ” side of the “TUNE/TRACK” button. Each time you push the button, the radio will step up or down to another frequency. If you push and hold the button, and the radio will go into the seek mode. Seeking: ” side of the Push and hold the “ “TUNE/TRACK” button. The radio will seek up or down for a station of the nearest frequency and will stop on reception. Each time you push the button, the stations will be searched one after another. Cassette tape player To fast forward a cassette tape, push and hold the “ ” side of the “TUNE/TRACK” button until “FF” appears on the screen. ” side of the “TUNE/ Push and hold the “ TRACK” button until “REW” appears on the screen to rewind a tape. Use this button to skip up or down to locate a song or recording.

” or “

” or “

You can select up to nine recordings (in- cluding current one). ” side of the “TUNE/ Push the “ TRACK” button. “FF 1” or “REW 1” will appear on the screen. Next, push either side of the track button until the number on the screen reaches the number of tracks you want to skip. If you push the button 10 times, the skip feature will be turned off. For the skip feature to work correctly a blank space of at least 3 seconds is con- sidered to be a start of a recording. When a beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken, live, or classical re- cordings.

255

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

” or “

Compact disc player Use this button to skip up or down to a different track. Push the “ ” side of the “TUNE/ TRACK” button until the number of the track you want to listen to appears on the screen. If you want to return to the begin- ning of the current track, quickly push the ” side of the “TUNE/TRACK” button one “ time. ” side of the Push and hold the “ “TUNE/TRACK” button to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing.

” or “

04 SIENNA_U (L/O 0408)

REPLACING CONTROLLER BATTERY For replacement, use 3 AAA batteries.

CAUTION

Special care should be that small children do not swallow the re- moved battery or components.

taken

NOTICE

z When replacing the battery, be care-

ful not to lose the components.

z Replace only with

the same or equivalent type of battery recom- mended by a Toyota dealer.

z Dispose of used batteries according

to local regulations.

Replace the battery according to the fol- lowing procedure: 1. Remove the cover of the controller as

shown.

256

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

2. Remove the discharged batteries and the new batteries as shown.

in

put Install the cover.

04 SIENNA_U (L/O 0408)

NOTICE

z Be sure that the positive side and negative side of the controller bat- tery should be faced correctly.

z Do not replace the battery with wet

hands. Water may cause rust.

z Do not touch or move any compo- nents inside of the controller, or it may interfere with proper operation. z Be careful not to bend the electrode

of the controller battery insertion.

z Close the battery case securely.

After replacing the battery, check that the controller operates properly. If the control- ler still does not operate properly, contact your Toyota dealer.

—DVD player The DVD player can play audio CDs, DVD video discs, CD texts, dts−CDs and video CDs. For appropriate discs for this player, see “Car audio/video system operating hints” on page 292 in this Section. The DVD player works when the ignition key is in the “ACC” or “ON” position. To turn on the DVD player, a disc must be loaded in the player. To turn off the player, eject the disc. Error messages If the player malfunctions, your audio sys- tem will display one of the three following error messages. the If screen: It indicates that the disc is dirty, damaged or it was inserted upside down. Clean the disc or insert it correctly. If “REGION CODE ERROR” appears on the screen: It indicates that the DVD re- gion code is not set properly. the If screen: There the player. Eject the disc. Set the disc again. If the malfunction still exists, take your vehicle to your Toyota dealer.

“DVD ERROR” appears on inside

“DISC CHECK” appears on

is a problem

257

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

If a disc which is not playable is inserted, “DISC CHECK” will also appear on the screen. For appropriate discs for this play- er, see “Car audio/video system operating hints” on page 292 in this Section. The player will play the track or chapter, and it will play from the beginning of the track or chapter again after it reaches the end.

NOTICE

Never try to disassemble or oil any part of the DVD player. Do not insert anything other than a disc into the slot.

8 cm (3 in.) compact disc singles Your compact disc player does not need an adaptor to play compact disc singles. Compact disc singles are about 8 cm (3
in.) than standard discs.

in diameter−smaller

NOTICE

Do not use an adaptor for compact disc singles—it could cause tracking errors or interfere with the ejection of compact discs.

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

INSERTING THE DISC Insert the compact disc into the slot with the label side up. “DISC” indicator light turns on while the disc is loaded. If the label faces down, the disc cannot be played. In this case, “DISC CHECK” and disc number appear on the screen.

258

04 SIENNA_U (L/O 0408)

—Selecting the DVD mode

the DVD mode, push

To select “DVD” button on the controller. You can also select the DVD mode on the mode selection screen mentioned above.

the

EJECTING THE DISC

Push the “

” button.

259

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

—DVD player operation switches

The “DVD Hint!” screen appears when the DVD mode is first selected after you turn the ignition key to the “ACC” or “ON” position. Push the “OK” switch when you read the message.

The DVD player can be operated with the controller buttons directly. 1. “DVD” button 2. “RETURN” button 3. “MENU” button 4. “AUDIO” button 5. “SUB TITLE” button 6. “ANGLE” button 7. “SET UP” button 8. “SEARCH” button 9. “TOP MENU” button 10. “

”, “"”, “AA” and “""” buttons

Controller

DVD player unit

260

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

the

the switch by

The player can also be operated with the switches on the screen. To operate the switches on the screen, select joy stick and push the “ENT” button. You cannot select the switches on the screen by touching them directly. When the switch is selected by the joy stick, the outline of the switch changes to blue. Push the switch will be highlighted in green.

“ENT” button, and

the

04 SIENNA_U (L/O 0408)

TURNING THE OPERATION SWITCHES ON AND OFF To turn on the operation switches, push the “CURSOR” button on the controller.

Controller

DVD player unit

261

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

Top page (DVD video operation switch)

Top page (DVD audio operation switch)

Top page (video CD)

Second page switch)

262

(DVD

video operation

Second page switch)

(DVD

audio operation

Second page (video CD)

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

There are operation switches on the “Top Page” and “Second Page” screens. “Top To change Page” or “Second Page” switch on the screen.

the screen, push

the

04 SIENNA_U (L/O 0408)

If “ you select a switch, it the switch cannot work.

” appears on the screen when indicates that

On the screen

Controller

263

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

To turn off the switches on the screen, push the “CURSOR” button on the control- ler once again or push the “Hide Keys” on the screen.

—DVD player operation (DVD video/DVD audio) NOTE: The playback condition of some DVD video discs may be determined by the DVD video software producer. This DVD player plays discs as the software producer intended. Therefore, some functions may not work properly. Be sure to read the instruction manual for the DVD video disc separately provided. For detailed information about DVD vid- eo discs, see “—DVD video disc infor- mation” on page 287 in this Section. Precautions for DVD video discs When recording on a DVD video, DVD audio, video CD or audio tracks may not record in some cases while the menu is displayed. As audio will not play in this case, verify that the video tracks are play- ing and then activate playback. The title/chapter number and playback time display may not appear while playing back certain DVD video discs.

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

DVD player unit

264

CAUTION

Conversational speech on some DVDs is recorded at a low volume to em- phasize the impact of sound effects. If you adjust the volume assuming that the conversations represent the maximum volume level available for the DVD, you may be startled by louder sound effects or when you change to a different audio source. Loud sounds may have a significant impact on the human body or pose a driving hazard. Keep in mind when you adjust the volume.

this

04 SIENNA_U (L/O 0408)

TURNING THE MENU SCREEN FOR THE DISC ON OR OFF DVD video— To turn on the menu screen for the disc, push the “Top Menu” or the “Menu” switch on the screen. You can also turn on the menu screen by pushing the “MENU” or “TOP MENU” switch on the controller. DVD audio— To turn on the menu screen for the disc, push the screen. You can also turn on the menu screen by pushing “TOP MENU” switch on the controller. For the operation of the menu screen, see the separate manual for the DVD disc.

“Top Menu” switch on

the

the

265

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

”, “

”, “

” or “

” switches on

To select the menu for the disc, push the the “ screen. Push the “Enter” switch to select the menu for the disc. You can also select the menu for the disc by the joy stick and the “ENT” button on the controller when the control switches are not indicated on the screen. Push the “Shift Keys” on the screen, and ”, “Enter” the switches (“ and “Shift Keys” switches) will move up and down. To turn off the switch, push the “OFF” switch on the switch again, push the “ON” switch on the screen. To return to the previous screen, push the “Back” switch on the screen.

the screen. To

turn on

”, “

”, “

”, “

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

To turn on the selecting switch, push the “

” switch.

266

04 SIENNA_U (L/O 0408)

”, “"”, “AA” AND

” switch/button: Push this switch/button

OPERATING THE “ “""” SWITCHES/BUTTONS “ to pause the disc. “"” switch/button: Push this switch/button to cancel the pause and return to normal playing. “AA” and “""” switches/buttons: Push and hold the “AA” or “""” switch/button to fast forward or reverse. If you want to return the current track, release the switch/button. DVD video only— “""” switch/button Push while pausing, the DVD video plays the slow−motion video replay or the slow−mo- tion video replay in reverse.

the beginning of

the “AA” or

to

267

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

SELECTING THE TITLE/GROUP To display the searching title (DVD video) or group (DVD audio) screen, push the “Search” switch on the screen. You can also display the screen by pushing the “SEARCH” button on the controller.

SKIPPING TO THE PREDETERMINED SCREEN To skip to the predetermined screen, push the “Return” switch. The DVD player starts playing from the beginning of the predeter- mined screen. You can also display the screen by pushing the “RETURN” button on the controller. For the predetermined screen, see the separate manual for the DVD disc.

further details of

268

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

for

that

“+10” switches and push

DVD video— Select the title number by using the “−”, “+” and the “Enter” switch to enter the number. The player starts playing disc title number. The selected title number will appear on the screen. Push the “Back” switch to return to the menu screen. DVD audio— Enter the group number by using the “−” and “+” switches. The selected group number will appear on the screen. Push the “Enter” switch. The player starts play- ing the disc from the entered group num- ber. Push the “Back” switch to return to the previous screen.

SELECTING THE BONUS GROUP DVD audio only— the Enter the bonus group number on the searching group screen and push “Enter” switch. The “Enter Key Code” screen will appear. To enter the number of the the group you want group number. the wrong number, push the “Clear” switch to delete the number. Push the “Enter” switch on the screen. The player starts playing the disc from the selected bonus group number.

to play, push

If you enter

269

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

DVD video

DVD audio

04 SIENNA_U (L/O 0408)

CHANGING THE SUBTITLE LANGUAGE Push the “Sub Title” switch on the screen, and then the changing subtitle language screen will appear. You can also display the screen by pushing the “SUB TITLE” button on the controller.

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

CHANGING THE STILL PICTURE DVD audio only— Push the “Still Prev.” or “Still Next” switch on the screen to forward or reverse the still pictures.

270

04 SIENNA_U (L/O 0408)

CHANGING AUDIO LANGUAGE the “Audio” switch on the screen Push then language and screen will appear. You can also display the screen by pushing the “AUDIO” button on the controller.

the changing audio

271

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

Each time you push the “Sub Title” switch, another language stored on the disc is selected. To turn off the subtitles, push the “Hide” switch. Push the “Back” switch to return to the previous screen. The selected subtitle language will appear on the screen.

04 SIENNA_U (L/O 0408)

turn off

language screen,

Each time you push the “Audio” switch, another language stored on the disc is selected. To the audio push the “Hide” switch. Push the “Back” switch to return to the previous screen. DVD video— The selected audio language will appear on the screen. DVD audio— The sound condition which is playing at present will appear on the screen.

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

DVD video

DVD audio

272

04 SIENNA_U (L/O 0408)

CHANGING ANGLE SCREEN Push the “Angle” switch on the screen, and then the changing angle screen will appear. You can also display the screen by pushing the “ANGLE” button on the controller.

the “Angle” switch,

The angle can be selected for discs that are multi−angle compatible when the ” mark appears on the screen. Each “ time you push the angle changes. The angle number which you can select will appear on the screen. To turn off the screen, push the “Hide” switch. Push the “Back” switch to return to the previous screen.

273

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

CHANGING THE INITIAL SETTING Push the “Set Up” switch on the screen, and then the initial setting screen will ap- pear. You can also display the screen by pushing the “SET UP” button on the con- troller. You can change the initial setting. After the setting is done, the player plays from the beginning of the chapter or the track.

Setup Menu 1 screen

the

the screen, push

There are initial setting switches on the “Setup Menu 1” and “Setup Menu 2” screens. To change “Top Page” or “Second Page” switch on the screen. After you change the initial setting, push the initial setting switch will be turned off and return to the picture previously. When the “Initial Setting” switch on “Setup Menu 2” is pushed, all menus are initial- ized.

“Enter” switch. The

274

Setup Menu 2 screen

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

the the “Select Audio

CHANGING THE AUDIO LANGUAGE Push the “Audio Lang.” switch on “Setup Menu 1” and Language” screens appear. Select the language you want to hear on the screen. To return to the “Setup Menu 1” screen, push the “Back” switch. If you cannot find a language you want to hear, push the “Others” switch. The “Enter Audio Lang. Code” screen will appear.

to hear, push

the number of

To enter the code of the language you want the language code. For details about the lan- guage codes, see the language code list. If you enter a wrong number, push the “Clear” switch to delete the number. If numbers which are not on the list are entered and the “Enter” switch is pushed, the “Incorrect Code” screen will appear. Push the language code you want to hear again. To return to the “Select Audio Language” screen, push the “Back” switch.

the

CHANGING THE SUBTITLE LANGUAGE To display “Select Subtitle Lang.”, push the “Subtitle Lang.” switch on the “Setup Menu 1” screen. Select the language you want to read on the screen. To return to the “Setup Menu 1” screen, push the “Back” switch. If you cannot find a language you want to read, push the “Others” switch. The “Enter Subtitle Lang. Code” screen will appear.

275

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

to read, push

the number of

To enter the code of the language you want the language code. For details about the lan- guage codes, see the language code list. If you enter a wrong number, push the “Clear” switch to delete the number. Push the “Enter” switch on the screen. If numbers which are not on the list are entered and the “Enter” switch is pushed, the “Incorrect code” screen will appear. Push the language code you want to read again. To return to the “Select Subtitle Lang.” screen, push the “Back” switch on the screen.

CHANGING THE DVD LANGUAGE To display the “Select DVD Language” screen, push the “DVD Language” switch on the “Setup Menu 1” screen. Select the language you want to read on the screen. If you cannot find a language you want to read, push the “Others” switch. The “Enter DVD Language Code” screen will appear. To return to the “Setup Menu 1” screen, push the “Back” switch. If you cannot find a language you want to read, push the “Others” switch. The “Enter DVD Language Code” screen will appear.

to read, push

the number of

To enter the code of the language you want the language code. For details about the lan- guage codes, see the language code list. If you enter a wrong number, push the “Clear” switch to delete the number. Push the “Enter” switch on the screen. If numbers which are not on the list are entered and the “Enter” switch is pushed, the “Incorrect code” screen will appear. Push the language code you want to read again. To return to the “Select DVD Language” screen, push the “Back” switch on the screen.

276

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

TURNING THE ANGLE MARK ON OR OFF The angle mark can be turned on discs that are multi−angle compatible. Each switch on turns on or off alternately.

the “Angle Mark” the angle mark

time you push

the screen,

for

OF

LEVEL

VIEWER

SETTING RESTRICTIONS You can restrict the play back screen by setting the viewer restrictions. You can prevent the restriction with a password. Some discs do not supply a restriction. To set the level of viewer restriction, push the “Parental” switch on the “Setup Menu 1” screen. The “Enter Personal Code” screen will appear.

Push the number for the password and the “Enter” switch. The “Select Restriction Level” screen will appear. If you enter a wrong number, push the “Clear” switch to delete the number. You cannot change the setting without in- putting the password. When you forget or change the “Clear” switch ten times to initialize the password. To return to the “Setup Menu 1” screen, push the “Back” switch.

the password, push

277

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

Push a parental level (1—8). The smaller the level number, the stricter the age limit. Push the “Back” switch to return to the “Setup Menu 1” screen.

SETTING THE DISPLAY MODE Each time you push the “Display Mode” switch on the “Setup Menu 2” screen, the display mode is changed from wide mode to auto mode.

278

LANGUAGE CODE LIST

Code

1001

0514

0618

0405

0920

0519

2608

1412

1620

1922

1821

1115

0512

0101

0102

0106

0113

0118

0119

Language

Japanese

English

French

German

Italian

Spanish

Chinese

Dutch

Portuguese

Swedish

Russian

Korean

Greek

Afar

Abkhazian

Afrikaans

Amharic

Arabic

Assamese

2004 SIENNA from Aug. ’04 Prod. (OM45422U)

04 SIENNA_U (L/O 0408)

0125

0126

0201

0205

0207

0208

0209

0214

0215

0218

0301

0315

0319

0325

0401

0426

0515

0520

0521

0601

0609

Aymara

Azerbaijani

Bashkir

Byelorussian

Bulgarian

Bihari

Bislama

Bengali

Tibetan