2000 Toyota Sienna Owners Manual

00 SIENNA(U)

lever or by depressing

RESUMING THE PRESET SPEED If the preset speed is cancelled by pulling the control the brake pedal or clutch pedal, pushing the lever up in the “RES/ACC” direction will restore the speed set prior to cancellation. However, once the vehicle speed falls be- low about 40 km/h (25 mph), the preset speed will not be resumed. CRUISE CONTROL FAILURE WARNING If the “CRUISE” indicator light in the in- strument cluster flashes when using the cruise control, press the “CRUISE ON− OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system. D The indicator light does not come on. D The indicator light flashes again. D The

light goes out after

indicator

it

comes on.

If this is the case, contact your Toyota dealer and have your vehicle inspected.

135

00 SIENNA(U)

136

00 SIENNA(U)

SECTION 1− 7

OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference Using your audio system Audio remote controls Car audio system operating hints

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

138
138
153
155

137

00 SIENNA(U)

Reference

Type 1: AM·FM ETR radio/cassette player/ compact disc player/compact disc auto changer controller

Type 2: AM·FM ETR radio/cassette player/ compact disc auto changer controller/ compact disc auto changer

Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” to turn the audio system on and off. Push “AM”, “TAPE” or “CD” to turn on that function without pushing “PWR·VOL”. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. If the another function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “AM”, “FM1·2”, “TAPE” or “CD” if the system to switch from one function to another.

is already on but you want

138

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange, and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange, and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.

00 SIENNA(U)

YOUR RADIO ANTENNA To remove an antenna, carefully turn it counterclockwise.

NOTICE

z Mast type antenna:

To prevent damage to the antenna, make sure is removed before driving your Toyota through an au- tomatic car wash.

it

z On−glass antenna (built−in on the

rear window glass): Attaching the film (especially con- ductive or metallic type) on the rear glass will noticeably the sensitivity of the radio.

reduce

YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should be to the right.

NOTICE

Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.

YOUR COMPACT DISC PLAYER When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The compact disc player will play from track 1 through the end of the disc. Then it will play from track 1 again. On models with the compact disc auto changer, next disc will be played from track 1.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a compact disc into the slot.

The player is intended for use with 12 cm (5 in.) discs only.

139

00 SIENNA(U)

—Controls and features "Type 1

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

140

00 SIENNA(U)

(Program)

Push “ ” to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates top side, “ Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

” indicates bottom side). feature: After

(Reverse/Fast forward buttons)

Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”.

fast

the

the

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).

(Eject button) the cassette

Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.

If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto−re- verse feature. Compact Disc Player forward or reverse If you want to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation.

141

00 SIENNA(U)

the

from

from

range

range

the knob

the knob

the display. Then

the display. Then

For front/rear adjustment, push “CONTROL / MODE” repeatedly until “FAd” appears on turn to adjust the front/rear balance. The display will show the “FAd−F7” to “FAd−R7”. For left/right adjustment, push “CONTROL / MODE” repeatedly until “BAL” appears on to turn adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”. CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages.

time you push “CD”,

inserted up−side down. Clean

If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc. If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer.

loaded

inside

it the

is

the

tone

from

range

is used

low−pitch

to adjust

/ MODE”

CONTROL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. tone adjustment, push For “CONTROL repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS −5” to “BAS 5”. tone adjustment, push For middle−pitch “CONTROL / MODE” repeatedly until “MId” appears on the knob to suit your preference. The display will show the range from “MId −5” to “MId 5”. tone adjustment, push For high−pitch “CONTROL repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE −5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers.

the display. Then

is also used

/ MODE”

to adjust

range

turn

from

the

142

00 SIENNA(U)

DISC ƝƜ Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display.

B NR∗

Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push the button marked with the double−D symbol. The double−D symbol will appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM1·2
Push “FM1·2” to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each button.

If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order. Random playing for the tracks on a disc: Quickly ”. “ ” will appear on the display. The disc you are listening to will play in ran- dom order. If you hear a beep, you held the button too long, and the player will play all the magazine in random order. To turn off the random fea- ture, push this button again.

release

tracks

listen

push

and

the

the

to

in

“

Compact disc auto changer only— Random playing for all the tracks in the magazine: Push and hold “ ” until you hear a beep. “ ” will appear on the display and the player will perform all the tracks on all the discs in the magazine in ran- dom order. To turn off the random feature, push this button again. RPT (Repeat) Cassette Player

track ends,

Push “ ” while the track is playing. ” will appear on the display. When “ the it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.

143

00 SIENNA(U)

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “SCAN” until you hear a beep. The radio will tune in the next pre- set station up the band, stay there for 5
seconds, and then move to the next pre- set station. To select a station, push “SCAN” again. To scan all the frequencies: Quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan the preset sta- tions. The radio will find the next station up the station band, stay there for 5 sec- onds, and then scan again. To select a station, push “SCAN” again.

Compact Disc Player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “ ” while the track is playing. “ ” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This process will be continued until you push the button again to turn off the re- peat feature. Compact disc auto changer only— Repeating a disc: Push and hold “ ” until you hear a beep. “ ” will appear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature.

144

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push “ ·SCAN” will appear on the display and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning.

“SCAN” again.

If

00 SIENNA(U)

the seek mode,

the radio finds and the next station up or down the

SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “Ɯ” or “Ɲ” under the “SEEK”. Do this again to find another station. Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display.

If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. D After tape

the beginning of

is the player will automatically

reached, start playing the same side.

the

D After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to pre- vent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion.

TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player. TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.

the beginning of

to

145

00 SIENNA(U)

Details of specific buttons, controls, and features are described in the alphabetical listing that follows.

"Type 2

146

00 SIENNA(U)

Compact disc To eject one compact disc only: Push and release the compact disc eject button. If you hold the button too long (if the audio system is on at this time, you hear a beep.), the mechanism will change to the mode for ejecting all the discs loaded in the changer. You can also eject any spe- cific one of the discs loaded in the chang- er as follows:

1. Push either side of the “DISC” button until the number of the disc you want to eject is displayed.

2. Push and release the compact disc

eject button.

To eject all the discs loaded in the chang- er: Push and hold the compact disc eject button (until you hear a beep when the audio system is on). The last compact disc played before pushing the button will be ejected first. If a disc is left in the slot for a long time, the function to eject all the discs will be automatically cancelled. After you turn the ignition to “LOCK”, you will be able to eject one compact disc only or all the discs loaded in the chang- er, but you will not be able to reinsert it or them.

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).

(Eject button)

the cassette

tape eject button to

Cassette tape Push eject a cassette. After you turn the ignition to “LOCK”, you will be able to eject a cassette, but you will not be able to reinsert it.

(Program)

Push “ ” to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates top side, “ Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

” indicates bottom side). feature: After

(Reverse/Fast forward buttons)

Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”.

fast

the

the

147

00 SIENNA(U)

If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto−re- verse feature. Compact Disc Player forward or reverse If you want to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation.

148

the

tone

from

range

is used

low−pitch

to adjust

/ MODE”

CONTROL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. tone adjustment, push For “CONTROL repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS −5” to “BAS 5”. tone adjustment, push For middle−pitch “CONTROL / MODE” repeatedly until “MId” appears on the knob to suit your preference. The display will show the range from “MId −5” to “MId 5”. tone adjustment, push For high−pitch “CONTROL repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE −5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers.

the display. Then

is also used

/ MODE”

to adjust

range

from

turn

the

the

from

from

range

range

the knob

the knob

the display. Then

the display. Then

For front/rear adjustment, push “CONTROL / MODE” repeatedly until “FAd” appears on turn to adjust the front/rear balance. The display will show the “FAd−F7” to “FAd−R7”. For left/right adjustment, push “CONTROL / MODE” repeatedly until “BAL” appears on to turn adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”. CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. If the player or another unit equipped with the player malfunctions, your audio system will display one of the six following error messages.

00 SIENNA(U)

B NR∗

Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push the button marked with the double−D symbol. The double−D symbol will appear on the display. Push the button again to turn off Dolbyr B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM1·2
Push “FM1·2” to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each button. If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation.

LOAD This button is used to load the compact discs in the compact disc auto changer which is integrated with the radio and cas- sette player. This compact disc auto changer can store up to 6 discs. The key must be in the “ACC” or “ON” position. Loading one compact disc only— To load one compact disc only, quickly push and release the button. If you hold the button too long (if the audio system is on at this time, you hear a beep.), the mechanism will change to the mode for loading multiple compact discs. After pushing the button, insert a compact disc. At this time, the indicators on both sides of the slot are flashing. After the disc is loaded, the shutter of the slot will close and the indicators will stop flashing. If no compact disc is inserted, the shutter will close after 15 seconds.

149

is

it the

inside

loaded

inserted up−side down. Clean

If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc. If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. DISC ƝƜ By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display.

00 SIENNA(U)

“

in

the

and

push

tracks

release

Random playing for the tracks on a disc: Quickly ”. ” will appear on the display. The “ disc you are listening to will play in ran- dom order. If you hear a beep, you held the button too long, and the player will play all the magazine in random order. To turn off the random fea- ture, push this button again. Random playing for all the tracks in the magazine: Push and hold “ ” until you hear a beep. “ ” will appear on the display and the player will perform all the tracks on all the discs in the magazine in ran- dom order. To turn off the random feature, push this button again.

RPT (Repeat) Cassette Player

track ends,

Push “ ” while the track is playing. “ ” will appear on the display. When the it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly. Compact Disc Player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “ ” while the track is playing. “ ” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This process will be continued until you push the button again to turn off the re- peat feature.

Loading multiple compact discs— To load multiple compact discs, push and hold (until you hear a beep when the au- dio system is on). After pushing the but- ton, insert the first compact disc. At this time, the indicators on both sides of the slot are flashing. After the disc is loaded, the shutter of the slot will close and the indicators will stop flashing. After a few seconds, the shutter will automatically open again so the next disc can be in- serted. The same process can be applied for loading the rest of the discs. If no compact disc is inserted, the shutter will close after 15 seconds. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order.

listen

the

to

150

00 SIENNA(U)

Repeating a disc: ” until you hear a Push and hold “ ” will appear on the display. beep. “ The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature. SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “SCAN” until you hear a beep. The radio will tune in the next pre- set station up the band, stay there for 5
seconds, and then move to the next pre- set station. To select a station, push “SCAN” again.

To scan all the frequencies: Quickly push and release “SCAN”. If you hear a beep, you held the button too long, and the radio will scan the preset sta- tions. The radio will find the next station up the station band, stay there for 5 sec- onds, and then scan again. To select a station, push “SCAN” again. Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning.

If

“SCAN” again.

the seek mode,

Scanning the first track of all the discs in the magazine: Push “SCAN” until you hear a beep. “ ·SCAN” will appear on the display and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning. SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “Ɯ” or “Ɲ” under the “SEEK”. Do this again to find another station. Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display.

the radio finds and the next station up or down the

151

00 SIENNA(U)

There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to pre- vent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player.

TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Turn the knob clockwise to step up the frequency. Turn the knob counterclock- wise to step down the frequency.

the beginning of

to

Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display. If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. D After tape

the beginning of

is the player will automatically

reached, start playing the same side.

the

D After the end of the tape is reached, the player will automatically reverse sides and start playing the other side.

152

00 SIENNA(U)

Audio remote controls

Some parts of the audio system can be adjusted with the buttons on the steering wheel. Details of the specific buttons, controls, and features are described below. 1. “Ɯ” and “VOL Ɲ” Buttons 2. “MODE” Button 3. “no” Button 4. “MUTE” Button

153

00 SIENNA(U)

1. “Ɯ” and “VOL Ɲ” Buttons (Volume

Up/Down)

to

increase while

to increase the volume. The the

Push “Ɯ” volume continues button is being pressed. Push “VOL Ɲ” to decrease the volume. The volume continues to decrease while the button is being pressed. 2. “MODE” Button Push “MODE” to select an audio mode. Each push changes the mode sequentially if the desired mode is ready to use. 3. “no” Button (Seek, Search, Track) Radio In plays down the station band. To seek a station, push the “n” or “o” side of the button. Do this again to find the next station. If you push the button on either side dur- ing the seek mode, seeking will be can- celled. Cassette player By using this button, you can skip to a different track in either direction. You can skip up to nine tracks at a time.

the radio finds and the next station by going up or

the seek mode,

154

Push the “n” or “o” side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the track you want to listen to is set. If you push the button ten times, the skip function will turn off. When counting the number of the tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two before the song you are listening to, push the “o” side of the button three times. If you push the track button further than you wanted to, push the other side of the button. The track number will be increased or reduced. The track number you select is not valid if the tracks remaining on the current side of the cassette. D When the tape reaches to the begin- ning, the player will automatically start playing that side.

the number of

is higher

than

it

D After the tape reaches to the end, the reverse and

player will automatically start playing the other side.

There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken, live, or classical recordings. Compact disc player By using this button, you can skip to a different track in either direction. Push either side of the track button until the track you want to listen to is set. If you want to return to the beginning of the current track, push the “o” side of the button once, quickly. 4. “MUTE” Button Push “MUTE” to turn the volume off mo- mentarily. This is cancelled by doing the following: D Push “MUTE” once again. D Push “Ɯ” or “VOL Ɲ”. D Operate any of the buttons or knobs on

function

the audio system itself.

D Disconnect the electrical power source.

00 SIENNA(U)

Car audio system operating hints

NOTICE

To ensure the correct audio system operation: z Be careful not to spill beverages

over the audio system.

z Do not put anything other than a cassette tape or Compact Disc into the slot.

z The use of cellular phone inside or near the vehicle may cause a noise from the speakers of the audio sys- tem which you are to. However, this does not indicate a malfunction.

listening

RADIO RECEPTION Usually, a problem with radio reception does not mean there is a problem with your radio—it is just the normal result of conditions outside the vehicle. For example, nearby buildings and terrain can interfere with FM reception. Power lines or telephone wires can interfere with AM signals. And of course, radio signals have a limited range, and the farther you are from a station, the weaker its signal will be. In addition, reception conditions change constantly as your vehicle moves.

signals are

Here are some common reception prob- lems that probably do not indicate a prob- lem with your radio: FM Fading and drifting stations—Generally, the effective range of FM is about 40 km (25
miles). Once outside this range, you may notice fading and drifting, which increase with the distance from the radio transmit- ter. They are often accompanied by distor- tion. Multi−path—FM reflective, making it possible for two signals to reach your antenna at the same time. If this happens, the signals will cancel each oth- er out, causing a momentary flutter or loss of reception. Static and fluttering—These occur when signals are blocked by buildings, trees, or other large objects. Increasing the bass level may reduce static and fluttering. the FM signal you Station swapping—If are interrupted or weak- is ened, and there is another strong station nearby on the FM band, your radio may tune in the second station until the origi- nal signal can be picked up again.

listening to

they can

AM Fading—AM broadcasts are reflected by the upper atmosphere—especially at night. These reflected signals can interfere with those received directly from the radio sta- tion, causing the radio station to sound alternately strong and weak. Station interference—When a reflected sig- nal and a signal received directly from a radio station are very nearly the same frequency, interfere with each other, making it difficult to hear the broad- cast. Static—AM is easily affected by external sources of electrical noise, such as high tension power lines, lightening, or electri- cal motors. This results in static. CARING FOR YOUR CASSETTE PLAYER AND TAPES For high performance from your cassette player and tapes: Clean the tape head and other parts regu- larly. D A dirty

tape head or tape path can decrease sound quality and tangle your cassette to clean them is by using a cleaning tape. (A wet type is recommended.)

tapes. The easiest way

155

00 SIENNA(U)

D If moisture gets into your compact disc player, you may not hear any sound even though your compact disc player appears the disc from the player and wait until it dries.

to be working. Remove

Use high−quality cassettes. D Low−quality cassette tapes can cause many problems, including poor sound, inconsistent and constant auto−reversing. They can also get stuck or tangled in the cassette player.

playing

speed,

D Do not use a cassette if it has been damaged or tangled or if its label is peeling off.

D Do not leave a cassette in the player if you are not listening to it, especially if it is hot outside.

D Store cassettes in their cases and out

of direct sunlight.

D Avoid using cassettes with a total play- ing time longer than 100 minutes (50
minutes per side). The tape used in these cassettes is thin and could get stuck or tangled in the cassette player.

156

CARING FOR YOUR COMPACT DISC PLAYER AND DISCS D Use only compact discs

labeled as

shown.

D Extremely high temperatures can keep your compact disc player from working. On hot days, use the air conditioning to cool the vehicle interior before you listen to a disc.

D Bumpy roads or other vibrations may

make your compact disc player skip.

00 SIENNA(U)

D Your automatic changer or compact disc player cannot play special shaped or low−quality compact discs such as those shown here. Do not use them as the changer or player could be dam- aged.

inserting

D Handle compact discs carefully, espe- them. cially when you are them on the edge and do not Hold bend them. Avoid getting fingerprints on them, particularly on the shiny side. D Dirt, scrapes, warping, pin holes, or the other disc damage could cause player to skip or to repeat a section of a track. (To see a pin hole, hold the disc up to the light.)

D Remove discs from the compact disc

CAUTION

Compact disc players use an invisible laser beam which could cause hazard- ous if directed outside the unit. Be sure to operate the player correctly.

radiation exposure

them. Store

player when you are not listening to their plastic cases away from moisture, heat, and direct sunlight.

them

in

To clean a compact disc: Wipe it with a soft, lint−free cloth that has been damp- ened with water. Wipe in a straight line from the center to the edge of the disc (not in circles). Dry it with another soft, lint−free cloth. Do not use a conventional record cleaner or anti−static device.

157

00 SIENNA(U)

158

00 SIENNA(U)

SECTION 1− 8

OPERATION OF INSTRUMENTS AND CONTROLS Air conditioning system Front air conditioning system

Controls Air flow selector settings Operating tips Side vents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

160
163
163
165

Rear air conditioning system

Controls Air flow selector settings Roof vents

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

166
169
169

159

Front air conditioning system— —Controls

00 SIENNA(U)

1. Temperature Selector 2. Air Intake Selector 3. Air Flow Selector 4. “A/C” Button (on some models) 5. Fan Speed Selector

160

00 SIENNA(U)

Fan speed selector Turn the knob to adjust the fan speed—to the right to increase, to the left to de- crease. Temperature selector Turn the knob to adjust the temperature— to the right to warm, to the left to cool.

5. Windshield—Air flows mainly from the

windshield vents. Use with the air intake selector posi- tioned in Fresh.

For details about air flow selector settings, see the illustration after “A/C” button. Turning to wind- shield position turns on the defroster to clear the front view more quickly.

the Air Flow Selector

Air flow selector Turn the knob to select the vents used for air flow. 1. Panel—Air

flows mainly

the in-

from

strument panel vents.

2. Bi−level—Air flows from both the floor vents and the instrument panel vents. 3. Floor—Air flows mainly from the floor

vents.

the

4. Floor/Windshield—Air

flows mainly floor vents and windshield

from vents. Use with the air intake selector posi- tioned in Fresh.

161

00 SIENNA(U)

“A/C” button To turn on the air conditioning, press the “A/C” button. The “A/C” button indicator will come on. To turn the air conditioning off, press the button again. If the “A/C” button indicator flashes, there is a problem in the air conditioning system and the air conditioning automatically shuts off. If this happens, take your ve- hicle to a Toyota dealer for service.

Air intake selector Move the lever to select the air source. 1. Recirculate—Recirculates the air inside

the vehicle.

2. Fresh—Draws outside air into the sys-

tem.

162

00 SIENNA(U)

—Air flow selector settings

—Operating tips D To cool off your Toyota after

it has been parked in the hot sun, drive with the windows open for a few minutes. This vents the hot air, allowing the air conditioning to cool the interior more quickly.

D Make sure the air intake grilles in front of the windshield are not blocked (by leaves or snow, for example).

D On humid days, do not blow cold air on the windshield. The windshield could fog up because of the difference in air temperature on the inside and outside of the windshield.

D Keep the area under the front seats clear to allow air to circulate through- out the vehicle.

D On cold days, move the fan speed to “HI” for a minute to help clear the in- take ducts of snow or moisture. This can reduce the amount of fogging on the windows.

D When driving on dusty roads, close all windows. If dust thrown up by the ve- hicle is still drawn into the vehicle after closing the windows, it is recommended that the air intake selector be set to FRESH and the fan speed selector to any setting except “OFF”.

163

00 SIENNA(U)

Air conditioning For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards COLD

(blue zone)

Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—ON D For quick cooling, move the air intake selector to recirculate for a few min- utes.

Ventilation For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards COLD

(blue zone)

Air intake—FRESH (outside air) Air flow—PANEL Air conditioning—OFF

Defogging The inside of the windshield For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards WARM

(red zone) to heat; COLD (blue zone) to cool

Air intake—FRESH (outside air) Air flow—WINDSHIELD

the “A/C” button

the Air Flow Selector

Turning to wind- shield position turns on the defroster to clear the front view more quickly. Vehicles with “A/C” button— Press for dehumidified heating or cooling. This setting clears the front view more quickly. D On humid days, do not blow cold air on the windshield—the difference be- tween the outside and inside tempera- tures could make the fogging worse.

D If following another vehicle on a dusty road, or driving in windy and dusty conditions, it is recommended that the air intake selector be temporarily set to RECIRCULATE, which will close off the outside passage and prevent outside air and dust from entering the vehicle interior.

Heating For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards WARM

(red zone)

Air intake—FRESH (outside air) Air flow—FLOOR Air conditioning—OFF D For quick heating, select recirculated air the windows from fogging, select fresh af- ter interior has been warmed.

few minutes. To keep

the vehicle

for a

D Press the “A/C” button on for dehumidi-

fied heating.

D Choose floor/windshield air flow to heat the vehicle interior while defrosting or defogging the windshield.

164

Defrosting The outside of the windshield For best results, set controls to:

Fan speed—Any setting except “OFF” Temperature—Towards WARM

(red zone)

Air intake—FRESH (outside air) Air flow—WINDSHIELD

the Air Flow Selector

Turning to wind- shield position turns on the defroster to clear the front view more quickly. Vehicles with “A/C” button— Press for dehumidified heating or cooling. This setting clears the front view more quickly. D To heat the vehicle interior while de- floor/

the windshield, choose

the “A/C” button

frosting windshield air flow.

00 SIENNA(U)

If air flow control is not satisfactory, check the side vents. The side vents may be opened or closed as shown.

165

—Side vents

Driver’s side

Passenger’s side

Rear air conditioning system— —Controls "4−door models

00 SIENNA(U)

1. Fan speed selector (front) 2. Fan speed selector (rear) 3. Air flow selector 4. Temperature selector

166

"5−door models

00 SIENNA(U)

1. Fan speed selector (front) 2. Fan speed selector (rear) 3. Temperature selector 4. Air flow selector

167

00 SIENNA(U)

Air flow selector (4−door models)

Air flow selector (5−door models)

Turn the knob to select the vents used for air flow. 4−door models— 1. Panel—Air flows mainly from the door

panel vents.

2. Bi−level—Air flows from both the door

panel vents and floor vents.

3. Floor—Air flows mainly from the floor

vents.

5−door models— 1. “A/C”—Air flows mainly from the roof

vents.

2. Except “A/C”—Air flows mainly from

the floor vents.

the right

to the left

to increase,

1. Fan speed selector (front) This lever is used to turn the rear air conditioning system on and off, and adjust the fan speed. Move the lever to “REAR” so that you can operate the rear air conditioning system by the rear controller. Move the lever to adjust the fan speed— to to decrease. Moving the lever to “OFF” turns off the rear air conditioning system and the system cannot be operated by the rear controller. 2. Fan speed selector (rear) When the front fan speed selector is in “REAR”, you can operate it. Move the lever to adjust the fan speed— to to decrease. Temperature selector 4−door models— Move tempera- lever ture—to the right to warm, to the left to cool. 5−door models— Move lever tempera- ture—to the right to warm, to the “A/C” position to cool.

to increase,

to the left

to adjust

to adjust

the right

the

the

the

the

168

00 SIENNA(U)

—Air flow selector settings

—Roof vents

Open

Close

If air flow control is not satisfactory, check the roof vents. The roof vents may be opened or closed as shown.

4−door models

5−door models

169

00 SIENNA(U)

170

00 SIENNA(U)

SECTION 1− 9

OPERATION OF INSTRUMENTS AND CONTROLS Other equipment Clock Cigarette lighter and ashtray Power outlets Glove box Garage door opener box Auxiliary boxes Cup holder First−aid kit and warning reflector holder Tire pressure warning system Floor mat

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

172
172
173
173
174
177
178
179
180
181

171

00 SIENNA(U)

Clock

Cigarette lighter and ashtray

ASHTRAY To use the ashtray, open out. finished with your cigarette, thor- When oughly extinguish it in the ashtray to pre- vent other cigarette butts from catching fire. After using the ashtray, push it back in completely. To remove the ashtray, press down on the lock spring plate and pull out.

CAUTION

To reduce the chance of in case of an accident or sudden stop while driving, always push the ash- tray back in completely after using.

injury

CIGARETTE LIGHTER To use the cigarette lighter, press it in. When it becomes heated, it automatical- ly pops out ready for use. If the engine is not running, the key must be in the “ACC” position. Do not hold the cigarette lighter pressed in. Use a Toyota genuine cigarette lighter or equivalent for replacement.

The digital clock indicates the time. The key must be in the “ACC” or “ON” position. To reset the hour: Push the “H” button. To reset the minutes: Push the “M” button. If the electrical power source has been disconnected from the clock, the time dis- play will automatically be set to 1:00 (one o’clock). When lights are turned on, the brightness of the time indi- cation will be reduced.

instrument panel

the

172

00 SIENNA(U)

Power outlets

Glove box

The power outlets are designed power supply for car accessories. The key must be in the “ACC” or “ON” position for the power outlets to be used.

for

NOTICE

the

z To prevent

fuse

from being blown, do not use the electricity over the total vehicle capacity of 12V/120W (front and rear outlets to- gether).

Front

Rear

z To prevent the battery from being discharged, do not use the power outlets longer than necessary when the engine is not running.

z Close the power outlet

lids when the power outlets are not in use. Inserting a foreign object other than the appropriate plug that fits the outlet, or allowing any liquid into the outlet may cause electrical fail- ure or short circuits.

To use the glove box, do this. To open: Pull the lever. To lock: Insert the master key and turn it clockwise.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.

injury

173

00 SIENNA(U)

Garage door opener box

The box is designed to store a garage door opener transmitter. Open the cover and remove the Velcro loop.

Remove the paper strip covering the adhe- sive on back side of loop and adhere loop to back side of the transmitter near cen- ter.

Please note if transmitter has wire clip for sun visor, this clip must be removed prior to adhesion of the Velcro.

174

00 SIENNA(U)

Remove spacers from the center panel. Place the largest spacer on the pin that would be below transmitter button when the cover is closed. Close the cover.

When the garage door opener transmitter is properly installed, you can operate the transmitter by pushing the center panel of the cover.

175

Place the transmitter with Velcro loop fac- ing inside of box into the box. Make sure the located above