105
00 SIENNA(U)
Headlights and turn signals (with automatic light control system)
The lights automatically turn off when any of the doors is opened with the ignition key in the “ACC” or “LOCK” position. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.
NOTICE
To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.
the
Daytime running light system (on some models) The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with light switch in the “OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights to full intensity for driving at night.
top of
the driver’s side
The automatic light control sensor is on the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor. If you feel that the automatic light control comes into operation too early or too late, have the sensor adjusted by your Toyota dealer.
tail,
license plate,
HEADLIGHTS
To turn on the following lights: Twist
the headlight/turn signal lever knob.
Position 1—Parking,
side marker and instrument panel lights
Position 2—Headlights and all of
above
Position 3 (“AUTO”)—Headlights and/or all
of the above
They automatically turn on or off depend-
ing on the darkness of the surroundings.
Manually twist the knob to the position 2
to turn on the headlights if they are need-
ed immediately when entering a dark tun-
nel, parking structure, etc.
the
106
00 SIENNA(U)
Headlights and turn signals (without automatic light control system)
High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.
the lever all
TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.
tail,
license plate,
HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above The lights automatically turn off when any of the doors is opened with the ignition turned off. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the head- light switch is off.
the
107
00 SIENNA(U)
NOTICE
To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.
the
Daytime running light system (on some models) The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with light switch in the “OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights to full intensity for driving at night.
108
High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.
the lever all
TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.
00 SIENNA(U)
Emergency flashers
Instrument panel light control
NOTICE
To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.
flashers,
turn on
the emergency
To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.
To adjust the brightness of the instru- ment panel lights, turn the dial.
109
00 SIENNA(U)
Personal lights
Front (with moon roof) The front personal lights operate sepa- rately with each lens. To turn on the light, push the lens on your side. To turn the light off, push the lens once again.
110
Front (without moon roof) The front personal lights operate sepa- rately with each lens. To turn on the light, push the lens on your side. To turn the light off, push the lens once again. To turn on the front personal push the switch. The following positions: “OFF”—Turns the light off. “DOOR”—Turns the light on when any of the front or sliding door is opened.
light switch has the
front personal
lights,
Center The center personal lights operate sep- arately with each lens. To turn on the light, push the lens on your side. To turn the light off, push the lens once again. To turn on the center personal lights, slide the switch. The center personal light switch has the following positions: “OFF”—Turns the light off. “DOOR”—Turns the light on when any of the front or sliding door is opened.
ILLUMINATED ENTRY SYSTEM Front (with moon roof)— The light comes on when either front or sliding door is opened. After all the doors are closed, the light remains on for about 15 seconds and then goes out. Front (without moon roof) and center— With the switch in the “DOOR” position, the light comes on when either front or sliding door is opened. After all the doors are closed, the light remains on for about 15 seconds and then goes out. However, in the following cases, the light goes out immediately: D All the doors are closed when the igni- tion key is in “ACC”, “ON” or “START” position.
D The ignition key is turned to “ACC”, “ON” or “START” when the light is still on.
D All the doors are locked when the light
is still on.
D One door will be closed with the lock knob pushed forward (front door) or downward (sliding door) while the other doors are locked.
00 SIENNA(U)
Interior light
the
OFF
CUT
LIGHTS
PERSONAL OPERATION When the ignition switch is “OFF” and any personal lights in the vehicle stay lighting on, lights will cut off automatically after 30 minutes with the light flashing five times. You can cancel the cut off operation by: D Turning the key to the “ACC” position. D Opening or closing any of front and
sliding doors
the
lights are cut off when all
D Turning off all the “ON” lights. All the doors are locked by key or wireless re- mote control transmitter. The key must be in the “OFF” position.
Front To turn on the front interior light, push the switch. The front interior light switch has the fol- lowing positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. Vehicles without power door lock system— “DOOR”—Turns the light on when any of the front door is opened. Vehicles with power door lock system— “DOOR”—Turns the light on when any of the front or sliding door is opened.
111
00 SIENNA(U)
ILLUMINATED ENTRY SYSTEM (with power door lock system) Front and center— With the switch in the “DOOR” position, the light comes on when either front or sliding door is opened. After all the doors are closed, the light remains on for about 15 seconds and then goes out. However, in the following cases, the light goes out immediately: D All the doors are closed when the igni- tion key is in “ACC”, “ON” or “START” position.
D The ignition key is turned to “ACC”, “ON” or “START” when the light is still on.
D All the doors are locked when the light
is still on.
D One door will be closed with the lock knob pushed forward (front door) or downward (sliding door) while the other doors are locked.
Rear To turn on the rear interior light, slide the switch. The rear interior light switch has the fol- lowing positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when any of sliding or back door is opened.
light,
interior
Center To turn on the center slide the switch. The center interior following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when any of front or sliding door is opened.
light switch has the
112
the
INTERIOR LIGHTS CUT OFF OPERATION When the ignition switch is “OFF” and any interior lights in the vehicle stay lighting on, lights will cut off automatically after 30 minutes with the light flashing five times. You can cancel the cut off operation by: D Turning the key to the “ACC” position. front and D Opening or closing any of
sliding doors
the
lights are cut off when all
D Turning off all the “ON” lights. All the doors are locked by key or wireless re- mote control transmitter. The key must be in the “OFF” position.
00 SIENNA(U)
Ignition switch light
Luggage compartment light
For easy access to the ignition switch, the ignition switch light comes on when any of the doors are opened. The light remains on for a certain time after all the doors are closed. Vehicles with power door lock system— When all the doors are locked or the igni- tion switch is turned to “ACC”, “ON” after all the doors are closed, the light fades out.
To turn the luggage compartment light on, open the back door and push the switch downwards. To turn it off, push the switch upwards or close the back door.
113
00 SIENNA(U)
Windshield wipers and washer
Rear window wiper and washer
To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.
the washer
NOTICE
Do not operate the wipers if the wind- shield the glass.
It may scratch
is dry.
To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.
Lever position
Speed setting
Position 1
Position 2
Position 3
Intermittent
Slow
Fast
interval adjuster: The
With “INT TIME” band lets you adjust the wiping time inter- val when the wiper lever is in the intermit- tent position (position 1). Twist the band upward time between sweeps, and downward to decrease it.
increase
the
to
114
To turn on the rear window wiper, twist the lever knob upward. The key must be in the “ON” position.
Lever position
Speed setting
Position 1
Position 2
Intermittent
Normal
To squirt washer fluid on the rear window, twist the knob upward or downward as far as it will go (position 3 or 4). The knob automatically returns from these positions after you release it. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7−3.
NOTICE
Do not operate the rear wiper if the rear window is dry. It may scratch the glass.
00 SIENNA(U)
Rear window and outside rear view mirror defoggers
To defog or defrost the rear window,
push the switch.
The key must be in the “ON” position.
The thin heater wires on the inside of the
rear window will quickly clear the window
surfaces. An indicator light will illuminate
to indicate the defogger is operating.
in the
On some models, heater panels
outside rear view mirrors will also quickly
clear the surfaces.
Push the switch once again to turn the
defoggers off.
The system will automatically shut off af-
ter the defoggers have operated about 15
minutes.
CAUTION
On some models, since the mirror surfaces can get hot, keep your hands off them when the defogger switch is on.
turn
Make sure you the defoggers off when the surfaces are clear. Leaving the defoggers on for a long time could cause the battery to discharge, especially during stop−and−go driving. The defoggers are not designed for drying rain water or for melting snow. If the outside rear view mirrors are heavi- ly coated with ice, use a spray de−icer before operating the switch.
NOTICE
When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires.
115
00 SIENNA(U)
116
00 SIENNA(U)
SECTION 1− 5
OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel gauge Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer Odometer and two trip meters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzers
118
118
119
120
120
117
00 SIENNA(U)
Fuel gauge
Engine coolant temperature gauge
the
The gauge works when ignition switch is on and indicates the approxi- mate quantity of fuel remaining in the tank. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. This fuel gauge has a non−return type needle which remains at the last indicated position when the ignition switch is turned off. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.
With tachometer
Without tachometer
With tachometer
Low fuel level warning light
Without tachometer
118
00 SIENNA(U)
Tachometer
The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: D Driving up a long hill on a hot day. D Reducing speed or stopping after high
speed driving.
D Idling for a long period with the air conditioning on in stop−and−go traffic.
D Towing a trailer.
NOTICE
z Do not remove the thermostat
in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.
z Do not continue driving with an overheated engine. See “If your ve- hicle overheats” in Section 4.
The tachometer indicates engine speed in thousands of rpm ( revolutions per minute). Use it while driving to select correct shift points and to prevent en- gine lugging and overrevving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.
NOTICE
Do not let the indicator needle get into the red zone. This may cause severe engine damage.
119
00 SIENNA(U)
Odometer and two trip meters
This meter displays the odometer and two trip meters. 1. Odometer—It shows the total distance
the vehicle has been driven.
2. Two trip meters—They show two differ- ent distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.
fuel economy and
the other
3. Trip meter reset knob—It can reset the to zero, and also
trip meters
two change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter B, then back the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.
to
With tachometer
Without tachometer
120
Service reminder indicators and warning buzzers
If the indicator or buzzer comes on...
Do this.
(a)
(b)
(type A)
(type B)
(instrument cluster— indicator and buzzer)
(c)
(clock display— indicator only)
If parking brake is off, stop and check.
Fasten driver’s seat belt.
Fasten front passenger’s seat belt.
(d)
Stop and check.
00 SIENNA(U)
If the indicator or buzzer comes on...
Do this.
If the indicator or buzzer comes on...
Do this.
(e)
(f)
(g)
(h)
(type A)
(type B)
(type A)
Low fuel level warning light
(type B)
(type A)
(type B)
Take vehicle to Toyota dealer.
(i)
(j)
Close all doors.
Close the right side sliding door.
(indicator and buzzer)
Fill up tank.
Stop and check.
Take vehicle to Toyota dealer.
(k)
(l) fluid.
(m)
Take vehicle to Toyota dealer immediately.
Add
washer
Adjust tire pressure.
(n)
Key reminder buzzer
Remove key.
(a) Brake System Warning Light This light has the following functions: Parking brake reminder If this light is on, make sure the parking brake is fully released. The light should go off. Low brake fluid level warning If this light comes on and stays on while you are driving, slow down and pull off the road. Then stop the vehicle carefully. Remember that stopping distance and ped- al effort may be increased. There maybe a problem somewhere in the brake sys- tem. Check the see− through reservoir. To make sure the parking brake has not caused to come on, check to see that the parking brake is fully released. If the brake fluid level is low... At a safe place, test your brakes by start- ing and stopping. D If you judge that the brakes still work to your
adequately, drive cautiously nearest dealer or shop for repairs.
the fluid level of
the warning
light
D If the brakes are not working, have the vehicle towed in for repairs. (For tow- ing information, see Section 4.)
121
00 SIENNA(U)
the
load
luggage
is placed on
Once the ignition key is turned to “ON” or “START”, the reminder light flashes if a passenger sits in the front passenger seat and does not pull out the seat belt. Un- less the front passenger starts to pull the shoulder belt out of the retractor, the light stays flashing. front If passenger seat, depending on its weight and how it is placed on the seat, built−in sensors in the seat cushion may detect the pressure, causing the reminder light to come on. (d) Discharge Warning Light This light warns that the battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system. The engine ignition will continue to oper- the battery ate, however, until is dis- charged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop.
NOTICE
Do not continue driving if the engine drive belt is broken or loose.
in
following
tank cap”
lamp comes on
(e) Malfunction Indicator Lamp This the cases. a. The fuel tank is completely empty. (See “Fuel gauge” in Section 1−5 for instruc- tions.) b. The fuel tank cap is not tightened se- curely. (See “Fuel in Section 1−2 for instructions.) c. There is a problem somewhere in your engine or automatic transmission electrical system. If it comes on while you are driving in case c, have your vehicle checked/re- paired by your Toyota dealer as soon as possible. (f) Low Fuel Level Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the low fuel level warning light may come on earlier than usual.
CAUTION
It is dangerous to continue driving normally when the brake fluid level is low.
If the brake fluid level is correct... Have the warning system checked by your Toyota dealer. (b) Driver’s Seat Belt Reminder Light
and Buzzer
to
remind you
light and buzzer
This buckle up the driver’s seat belt. Once the ignition key is turned to “ON” or “START”, the reminder light flashes and buzzer sounds if the driver’s seat belt is not pulled out. Unless the driver starts to pull the shoulder belt out of the retractor, the light keeps flashing and the buzzer stops after about 4 to 8 seconds. (c) Front Passenger’s Seat Belt Re-
minder Light
This light reminds you to buckle up the front passenger’s seat belt.
122
00 SIENNA(U)
(g) Low Oil Pressure Warning Light This light warns that the engine oil pres- sure is too low. If it flickers or stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota dealer or qualified repair shop for assistance. The flicker when the engine is idling or it may come on briefly after a hard stop. There is no cause for concern if it then goes out when the engine is accelerated slightly. The light may come on when the oil level is extremely is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.
light may occasionally
low. It
NOTICE
Do not drive the warning light on—even for one block. It may ruin the engine.
the vehicle with
(h) “ABS” Warning Light This light warns that there is a problem somewhere in your anti−lock brake sys- tem. If the light comes on while you are driv- ing, have your vehicle checked by your Toyota dealer as soon as possible. The light will come on when the ignition key is turned to the “ON” position. After a few seconds, the light will go off. When the “ABS” warning light is on (and the brake system warning light is off), the brake system operates conventionally but anti−lock brake system is not assisting brake performance so that the wheels can lock−up during sudden braking or braking on slippery road surfaces. (i) Open Door Warning Light This light remains on until all the doors and back door are completely closed. When the ignition switch is “OFF” and this light stays lighting on, the light will turn off automatically after 30 minutes with the times. See “Personal light lights” and “Interior in Section 1−4.
for details
flashing
light”
five
(j) Open Power Sliding Door Warning
Light and Buzzer
is not completely closed with
This light comes on if the power sliding door the ignition key in the “ON” position. If you forcibly close the power sliding door by hand when the ignition key is in the “ON” position, the open power sliding door warning light may stay on. In this case, try opening and closing the power sliding door again by hand slowly, or use one of the “PWR DOOR” switches or wireless remote control transmitter. If you shift out of “P” when the power sliding door is opened or in the process of closing with the power sliding door sys- tem on, a buzzer will sound and the open power sliding door warning light will flash. This is a warning that the sliding door is not completely closed.
123
00 SIENNA(U)
(m) Low Tire Pressure Warning Light This light warns that the tire pressure of any one of the tires is critically reduced. The light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the low tire pressure warning system is functioning properly. If the light comes on while driving, adjust tire pressure to the specified level. (See “Tires” in Section 8.) After the tire pres- sure is adjusted, the light should go off after driving at about more than 30 km/h (19 mph) for some time. If the light still remains, have the low tire pressure warn- ing system checked at your Toyota dealer. (n) Key Reminder Buzzer This buzzer reminds you to remove the key when you open the driver’s door with the ignition key in the “ACC” or “LOCK” position.
CHECKING SERVICE REMINDER INDICA- TORS (except the low fuel level warning light and low windshield washer fluid level warning light) 1. Apply the parking brake. 2. Open one of the doors.
The open door warning come on.
light should
3. Close the door.
The open door warning light should go off.
4. Turn the ignition key to “ACC”.
The SRS warning light should come on. It goes off after about 6 seconds.
5. Turn the ignition key to “ON”, but do
not start the engine. All the service reminder indicators ex- cept the open door warning light, open power sliding door warning light and SRS warning light should come on. The “ABS” warning light and low tire pres- sure warning light go off after a few seconds.
(k) SRS Warning Light This light will come on when the igni- tion key is turned to the “ACC” or “ON” position. After about 6 seconds, the light will go off. This means the system of the airbag and front seat belt pretensioners are operating properly. The warning light system monitors the air- bag sensor assembly, front airbag sen- sors, seat belt pretensioner assemblies, inflators, warning light, interconnecting wir- ing and power sources. If either of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ACC” or “ON” position or remains on.
D The light comes on or flashes while
driving.
(l) Low Windshield Washer Fluid Level
Warning Light
The light warns that the windshield washer fluid level is too low. Add washer fluid at your earliest opportunity. (For instructions, see “Adding washer fluid” in Section 7−3.)
124
00 SIENNA(U)
6. Vehicles with a power sliding door:
Open the right side sliding door. The open power sliding door warning light should come on. Close the right side sliding door. The open power sliding door warning light should go off.
If any service reminder indicator or warn- ing buzzer does not function as described above, either the bulb is burned out or the circuit it checked by your Toyota dealer as soon as possible.
repair. Have
in need of
is
125
00 SIENNA(U)
126
00 SIENNA(U)
SECTION 1− 6
OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch with steering lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
128
129
133
133
127
00 SIENNA(U)
You must push in the key to turn the key from “ACC” to the “LOCK” position. The selector lever must be put in the “P” posi- tion before pushing the key. Vehicles with engine immobiliser system— Once you remove the key, the engine im- mobiliser system is automatically set. (See “Engine in Section 1−2.) When starting the engine, the key may seem stuck at the “LOCK” position. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently.
immobiliser system”
NOTICE
leave the key
Do not in the “ON” position if the engine is not running. The battery will discharge and the ignition could be damaged.
Ignition switch with steering lock
“START”—Starter motor on. The key
will return to the “ON” position when
released.
For starting tips, see Section 3.
“ON”—Engine on and all accessories
on.
This is the normal driving position.
“ACC”—Accessories such as the radio
operate, but the engine is off.
the “ACC” or
If you
“LOCK” position and open
the driver’s
door, a buzzer will remind you to remove
the key.
“LOCK”—Engine is off and the steering
wheel
is locked. The key can be re-
moved only at this position.
128
the key
leave
in
00 SIENNA(U)
Automatic transmission
Selector lever
Overdrive switch
With the brake pedal depressed, shift while pulling the selector lever toward you (The ignition switch must be in “ON” or “ACC” position.)
Shift while pulling the selector lever toward you
Shift normally
Your automatic transmission has a shift lock system to minimize the possibility of incorrect operation. This means you can only shift out of “P” position when the brake pedal is depressed (with the ignition switch in “ON” or “ACC” position and the selector lever pulled toward you). (a) Selector lever The shift position is displayed on the in- strument cluster. P: Parking, engine starting and
key removal
R: Reverse N: Neutral D: Normal driving (with overdrive on) 2: Stronger engine braking L: Maximum engine braking
129
00 SIENNA(U)
Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking will not be applied because the cruise control is not cancelled. For ways to decrease the vehicle speed, see “Cruise control” in this section. (c) Normal driving 1. Start the engine as instructed in “How to start the engine” in Section 3. The transmission must be in “P” or “N”.
2. With your foot holding down the brake
pedal, shift the selector lever to “D”.
When the lever is in the “D” position, the automatic transmission system will select the most suitable gear for running condi- tions such as normal cruising, hill climb- ing, hard towing, etc. Always turn the overdrive on for better fuel economy and quieter driving. If the engine coolant the transmission will not shift into overdrive gear even with the overdrive on.
temperature
low,
is
CAUTION
Never put your foot on the accelera- tor pedal while shifting.
3. Release the parking brake and brake the accelerator pedal
pedal. Depress slowly for smooth starting.
(d) Using engine braking To use engine braking, you can downshift the transmission as follows: D Push the overdrive switch. The “O/D OFF” indicator light will come on and the transmission will downshift to the third gear.
D Shift into the “2” position. The trans-
mission will downshift
the second
gear when
the vehicle speed drops
down to or lower than 114 km/h (70
mph), and stronger engine braking will
be enable.
to
D Shift into the “L” position. The trans- mission will downshift to the first gear when the vehicle speed drops down to or lower than 59 km/h (36 mph), and maximum engine braking will be en- able.
Vehicles with cruise control—When the cruise control is being used, even if you downshift the transmission by pushing and releasing the overdrive switch, engine braking is not applied because the cruise control is not cancelled.
(b) Overdrive switch You can select either a third gear (with overdrive off) or fourth gear (with over- drive on) by pushing this switch. To turn the overdrive off, push the switch. The “O/D OFF” indicator light should come on. To turn the overdrive on again, push the switch again. The “O/D OFF” indicator light should go off. Always drive your vehicle with the over- drive on fuel economy and quieter driving. If the engine is turned off when the over- drive is off and restarted, the overdrive will automatically be on.
for better
130
00 SIENNA(U)
For ways to decrease the vehicle speed, see “Cruise control” in this section.
NOTICE
CAUTION
Be careful when downshifting on a slippery shifting could cause the vehicle to spin or skid.
surface. Abrupt
(e) Using “2” and “L” positions The “2” and “L” positions are used for strong engine braking as described pre- viously. With the selector lever in “2” or “L”, you can start the vehicle in motion as with the lever in “D”. With the selector lever in “2”, the vehicle will start in the first gear and automatical- ly shift to second gear. With the selector lever in “L”, the trans- mission is engaged in first gear.
z Be careful not to overrev the en- gine. Watch the tachometer to keep engine rpm from going into the red zone. The approximate maximum al- lowable speed for each position is given below for your reference:
“2” “L”
. . . . . . . . . . . . . . . . . . . . . . .
120 km/h (74 mph) 64 km/h (40 mph) z Do not continue hill climbing or hard towing for a long time in the “2” or “L” position. This may cause severe automatic transmission dam- age from overheating. To prevent such damage, “D” position should be used in hill climbing or hard towing.
(f) Backing up 1. Bring the vehicle to a complete stop. 2. With the brake pedal held down with your foot, shift the selector lever to the “R” position.
NOTICE
Never shift into reverse while the ve- hicle is moving.
(g) Parking 1. Bring the vehicle to a complete stop. 2. With
the brake pedal pressed down, fully depress the parking brake pedal to apply the parking brake securely.
3. With
the brake pedal pressed down, shift the selector lever to the “P” posi- tion.
CAUTION
Never attempt to move the selector lever into “P” position under any cir- cumstances while the vehicle is mov- ing. Serious mechanical damage and loss of vehicle control may result.
(h) Good driving practice D If the transmission repeatedly shifts up and down between third gear and over- drive when climbing a gentle slope, the overdrive should be turned off. Be sure to turn the switch on immediately after- ward.
D When towing a trailer, in order to main- tain engine braking efficiency, do not use overdrive.
131
00 SIENNA(U)
CAUTION
Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping.
NOTICE
Do not hold the vehicle on an up- grade with the accelerator pedal. It can cause the transmission to over- heat. Always use the brake pedal or parking brake.
(i) Rocking your vehicle if stuck
CAUTION
If your vehicle becomes stuck in snow, mud, sand, etc., then you may attempt to rock the vehicle free by moving it forward and backward. Do not attempt this procedure if people or objects are anywhere near the ve- hicle. During the rocking operation the vehicle may suddenly move for- ward or backward as it becomes un- stuck, causing injury or damage to nearby people or objects.
132
NOTICE
to
the
If you rock your vehicle, observe the following precautions to prevent dam- age transmission and other parts. z Do not depress the accelerator ped- al while shifting the selector lever or before the transmission is com- pletely shifted to forward or reverse gear.
z Do not race the engine and avoid
spinning the wheels.
z If your vehicle remains stuck after rocking the vehicle several times, consider other ways such as tow- ing.
Parking brake
00 SIENNA(U)
When parking, firmly apply the parking brake to avoid inadvertent creeping. To set: Fully depress the parking brake pedal. For better holding power, first de- press the brake pedal and hold it while setting the parking brake. To release: Depress pedal once again. To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake.
the parking brake
Type A
CAUTION
Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.
Type B
Cruise control
The cruise control allows you to cruise
the vehicle at a desired speed over 40
km/h (25 mph) even with your foot off
the accelerator pedal.
Your cruising speed can be maintained up
or down grades within the limits of engine
performance, although a slight speed
change may occur when driving up or
down
the grades. On steeper hills, a
greater speed change will occur so it is
better to drive without the cruise control.
CAUTION
D To help maintain maximum control of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow−covered) or winding roads.
If
D Avoid vehicle speed increases when driving downhill. the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.
133
00 SIENNA(U)
If you need acceleration—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the vehicle will return to the speed set prior to the acceleration. CANCELLING THE PRESET SPEED You can cancel the preset speed by: a. Pulling the lever in the “CANCEL” di-
rection and releasing it. b. Depressing the brake pedal.
If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto-
matically cancel out.
If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset
speed will also automatically cancel out.
If the preset speed automatically cancels
out other than for the above cases, have
your vehicle checked by your Toyota deal-
er at the earliest opportunity.
TURNING ON THE SYSTEM To operate the cruise control, press the “CRUISE ON−OFF” button. This turns the system on. The indicator light in the in- strument panel shows that you can now set the vehicle at a desired cruising speed. Another press will turn the system completely off.
CAUTION
To avoid accidental cruise control en- gagement, keep the “CRUISE ON− OFF” switch off when not using the cruise control.
SETTING AT A DESIRED SPEED
On vehicles with automatic transmission,
the transmission must be in “D” before
you set the cruise control speed.
Bring your vehicle to the desired speed,
push the lever down in the “SET/COAST”
direction and release it. This sets the ve-
hicle at that speed. If the speed is not
satisfactory, tap the lever up for a faster
speed, or tap it down for a slower speed.
Each tap changes the set speed by 1.6
km/h (1.0 mph). You can now take your
foot off the accelerator pedal.
134
RESETTING TO A FASTER SPEED Push the lever up in the “RES/ACC” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “SET/COAST” direction. RESETTING TO A SLOWER SPEED Push the lever down in the “SET/COAST” direction and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. However, a faster way to reset is to de- press the brake pedal and then push the lever down in the “SET/COAST” direction. Even if you turn off the overdrive switch, with the cruise control on, engine braking will not be applied because the cruise control is not cancelled. To decrease the vehicle speed, reset to a slower speed with the cruise control lever or depress the brake pedal. the brake pedal, cruise control is cancelled.
If you use
00 SIENNA(U)
lever or by depressing
RESUMING THE PRESET SPEED If the preset speed is cancelled by pulling the control the brake pedal or clutch pedal, pushing the lever up in the “RES/ACC” direction will restore the speed set prior to cancellation. However, once the vehicle speed falls be- low about 40 km/h (25 mph), the preset speed will not be resumed. CRUISE CONTROL FAILURE WARNING If the “CRUISE” indicator light in the in- strument cluster flashes when using the cruise control, press the “CRUISE ON− OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system. D The indicator light does not come on. D The indicator light flashes again. D The
light goes out after
indicator
it
comes on.
If this is the case, contact your Toyota dealer and have your vehicle inspected.
135
00 SIENNA(U)
136
00 SIENNA(U)
SECTION 1− 7
OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference Using your audio system Audio remote controls Car audio system operating hints
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
138
138
153
155
137
00 SIENNA(U)
Reference
Type 1: AM·FM ETR radio/cassette player/ compact disc player/compact disc auto changer controller
Type 2: AM·FM ETR radio/cassette player/ compact disc auto changer controller/ compact disc auto changer
Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” to turn the audio system on and off. Push “AM”, “TAPE” or “CD” to turn on that function without pushing “PWR·VOL”. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. If the another function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “AM”, “FM1·2”, “TAPE” or “CD” if the system to switch from one function to another.
is already on but you want
138
TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange, and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange, and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.
00 SIENNA(U)
YOUR RADIO ANTENNA To remove an antenna, carefully turn it counterclockwise.
NOTICE
z Mast type antenna:
To prevent damage to the antenna, make sure is removed before driving your Toyota through an au- tomatic car wash.
it
z On−glass antenna (built−in on the
rear window glass): Attaching the film (especially con- ductive or metallic type) on the rear glass will noticeably the sensitivity of the radio.
reduce
YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should be to the right.
NOTICE
Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.
YOUR COMPACT DISC PLAYER When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The compact disc player will play from track 1 through the end of the disc. Then it will play from track 1 again. On models with the compact disc auto changer, next disc will be played from track 1.
NOTICE
Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a compact disc into the slot.
The player is intended for use with 12 cm (5 in.) discs only.
139
00 SIENNA(U)
—Controls and features
"Type 1
Details of specific buttons, controls, and features are described in the alphabetical listing that follows.
140
00 SIENNA(U)
(Program)
Push “ ” to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates top side, “ Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.
” indicates bottom side). feature: After
(Reverse/Fast forward buttons)
Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”.
fast
the
the
to preset and
1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station (see “TUNE” knob or “SEEK” button). Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button (The display will show “AM”, “FM1” or “FM2” when you push “AM” “FM1·2”).
(Eject button) the cassette
Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.
If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto−re- verse feature. Compact Disc Player forward or reverse If you want to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation.
141
00 SIENNA(U)
the
from
from
range
range
the knob
the knob
the display. Then
the display. Then
For front/rear adjustment, push “CONTROL / MODE” repeatedly until “FAd” appears on turn to adjust the front/rear balance. The display will show the “FAd−F7” to “FAd−R7”. For left/right adjustment, push “CONTROL / MODE” repeatedly until “BAL” appears on to turn adjust the left/right balance. The display will show “BAL−L7” to “BAL−R7”. CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages.
time you push “CD”,
inserted up−side down. Clean
If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc. If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer.
loaded
inside
it the
is
the
tone
from
range
is used
low−pitch
to adjust
/ MODE”
CONTROL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. tone adjustment, push For “CONTROL repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS −5” to “BAS 5”. tone adjustment, push For middle−pitch “CONTROL / MODE” repeatedly until “MId” appears on the knob to suit your preference. The display will show the range from “MId −5” to “MId 5”. tone adjustment, push For high−pitch “CONTROL repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE −5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers.
the display. Then
is also used
/ MODE”
to adjust
range
turn
from
the
142
00 SIENNA(U)
DISC ƝƜ Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display.
B NR∗
Dolbyr
If you are listening to a tape that was
recorded with Dolbyr B Noise Reduction,
push the button marked with the double−D
symbol. The double−D symbol will appear
on the display. Push the button again to
turn off Dolbyr B NR.
The Dolby NR mode reduces tape noise
by about 10 dB. For best sound reproduc-
tion, play your tapes with this button on
or off according to the mode used for
recording the tape.
∗
: Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation. “DOLBY” and the
double D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
FM1·2
Push “FM1·2” to turn on the radio and
select the FM band. “FM1” or “FM2” will
appear on the display. This system allows
you to set twelve FM stations, two for
each button.
If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order. Random playing for the tracks on a disc: Quickly ”. “ ” will appear on the display. The disc you are listening to will play in ran- dom order. If you hear a beep, you held the button too long, and the player will play all the magazine in random order. To turn off the random fea- ture, push this button again.
release
tracks
listen
push
and
the
the
to
in
“
Compact disc auto changer only— Random playing for all the tracks in the magazine: Push and hold “ ” until you hear a beep. “ ” will appear on the display and the player will perform all the tracks on all the discs in the magazine in ran- dom order. To turn off the random feature, push this button again. RPT (Repeat) Cassette Player
track ends,
Push “ ” while the track is playing. ” will appear on the display. When “ the it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.