2009 Toyota Matrix Owners Manual

(U.S.A.)

(Canada)

Electric power steering warning light Indicates a malfunction in the EPS (Electric Power Steering) system.

Active torque control 4WD system warning light Indicates a malfunction in the active torque control 4WD system.

(AWD models)

n If the malfunction indicator lamp comes on while driving

First check the following: Is the fuel tank empty? If it is, fill the fuel tank immediately. Is the fuel tank cap loose? If it is, tighten it securely.

The malfunction indicator lamp will go off after taking several driving trips. If the malfunction indicator lamp does not go off even after several trips, con- tact your Toyota dealer as soon as possible.

354

5-2. Steps to take in an emergency

Follow the correction procedures.

After taking the specified steps to correct the suspected problem, check that the warning light turns off.

Warning light

Warning light/Details

Correction procedure

Open door warning light Indicates that a door is not fully closed. Low fuel level warning light Indicates that remaining fuel is about 2.0 gal. (7.5 L, 1.6 Imp. gal.) or less Driver’s seat belt reminder light (warning buzzer)* Warns the driver to fasten his/her seat belt. Front passenger’s seat belt reminder light (warning buzzer)* Warns the front passen- ger to fasten his or her seat belt.

Low windshield washer fluid warning light Low level of washer fluid

Check that all doors are closed.

Refuel the vehicle.

Fasten the seat belt.

Fasten the seat belt.

Fill the tank.

(on the center

panel)

(Canada)

355

5-2. Steps to take in an emergency

Warning light

Warning light/Details

Correction procedure

(U.S.A.)

Engine oil replacement reminder light

Illuminates for about 3 sec- onds and then flashes for about 15 seconds approxi- mately 4500 miles (7200 km) after the engine oil is changed: Indicates that the engine oil is scheduled to be changed. Comes on and remains on if the distance driven exceeds 5000 miles (8000 km): Indi- cates that the engine oil should be changed. Tire pressure warning light (if equipped)

Check the engine oil, and change if necessary.

Check and change the engine oil.

When the light comes on: Low tire inflation pressure.

Adjust the tire inflation pressure.

When the light comes on after blinking for 1 minute: Malfunction in the tire pressure warning system.

Have the system checked by your Toyota dealer.

*: Driver's and front passenger’s seat belt warning buzzers:

The driver’s and front passenger’s seat belts warning buzzers sound to alert the driver and front passenger that his or her seat belt is not fastened. The buzzer sounds intermittently for 10 seconds after the vehicle has reached a speed of 12 mph (20 km/h). Then, if the seat belt is still unfastened, the buzzer will sound at a different tone for 20 more seconds.

356

5-2. Steps to take in an emergency

n Front passenger detection sensor and passenger seat belt reminder

If luggage is placed on the front passenger seat, the front passenger detection sensor may cause the warning light to flash, even if a passen- ger is not sitting in the seat. If a cushion is placed on the seat, the sensor may not detect a passen- ger, and the warning light may not operate properly.

n Changing the engine oil (U.S.A. only)

Make sure to reset the oil change system. (→P. 293) n When the tire pressure warning light comes on

Check the tire inflation pressure and adjust to the appropriate level. Pushing the tire pressure warning reset switch does not turn off the tire pressure warning light.

n The tire pressure warning light may turn on due to natural causes

The tire pressure warning light may turn on due to natural causes such as natural air leaks or tire inflation pressure changes caused by temper- ature. In this case, adjusting the tire inflation pressure will turn off the warning light (after a few minutes).

357

5-2. Steps to take in an emergency

n When a tire is replaced with a spare tire

The compact spare tire is not equipped with the tire pressure warning valve and transmitter. If a tire goes flat, the tire pressure warning light will not turn off even though the flat tire is replaced with the spare tire. Replace the spare tire with the repaired tire and adjust the proper tire inflation pressure. The tire pressure warning light will turn off after a few minutes.

n If the tire pressure warning system is inoperative

The tire pressure warning system will be disabled in the following condi- tions: (When the condition becomes normal, the system will work properly.)

If tires not equipped with tire pressure warning valves and transmit- ters are used. If the ID code on the tire pressure warning valves and transmitters is not registered in the tire pressure warning computer. If the tire inflation pressure is 73 psi (500 kPa, 5.1 kgf/cm2 or bar) or higher.

The tire pressure warning system may be disabled in the following condi- tions: (When the condition becomes normal, the system will work properly.)

If electronic devices or facilities using similar radio wave frequencies are nearby. If a radio set at similar frequencies is in use in the vehicle. If a window tint that affects the radio wave signals is installed. If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings. If non-genuine Toyota wheels are used. (Even if you use Toyota wheels, the tire pressure warning system may not work properly with some types of tires.) If tire chains are used.

358

5-2. Steps to take in an emergency

n If the tire pressure warning light comes on after blinking for 1

minute frequently If the tire pressure warning light comes on after blinking for 1 minute fre- quently when the engine switch is turned to the “ON” position, have it checked by your Toyota dealer.

n Customization that can be configured at Toyota dealer

The vehicle speed linked seat belt reminder buzzer can be disabled. (Customizable features →P. 420) However, Toyota recommends that the seat belt reminder buzzer be operational to alert the driver and front passen- ger that the seat belts are not fastened.

CAUTION

n If the tire pressure warning light comes on

Be sure to observe the following precautions. Failure to do so could cause loss of vehicle control and result in death or serious injury. l Stop your vehicle in a safe place as soon as possible. Adjust the tire

inflation pressure immediately. If the tire pressure warning light comes on even after tire inflation pres- sure adjustment, it is probable that you have a flat tire. Check the tires. If the tire is flat, change to the spare tire and have the flat tire repaired by the nearest Toyota dealer.

l Avoid abrupt maneuvering and braking. If the vehicle tires deteriorate,

you could lose control of the steering wheel or the brakes.

n If a blowout or sudden air leakage should occur

The tire pressure warning system may not activate immediately.

359

5-2. Steps to take in an emergency

CAUTION

n Maintenance of the tires

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label). (If your vehicle has tires of a differ- ent size than the size indicated on the vehicle placard or tire inflation pressure label [tire and load information label], you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS-tire pressure warning system) that illuminates a low tire pressure telltale (tire pressure warning light) when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale (tire pressure warning light) illumi- nates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under- inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Please note that the TPMS (tire pressure warning system) is not a sub- stitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale (tire pressure warning light).

360

5-2. Steps to take in an emergency

CAUTION

Your vehicle has also been equipped with a TPMS (tire pressure warning system) malfunction indicator to indicate when the system is not operat- ing properly. The TPMS (tire pressure warning system) malfunction indi- cator is combined with the low tire pressure telltale (tire pressure warning light). When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illumi- nated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illumi- nated, the system may not be able to detect or signal low tire pressure as intended. TPMS (tire pressure warning system) malfunctions may occur for a vari- ety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS (tire pressure warning system) from functioning properly. Always check the TPMS (tire pres- sure warning system) malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alter- nate tires and wheels allow the TPMS (tire pressure warning system) to continue to function properly.

NOTICE

n Precaution when installing a different tire

When a tire of a different specification or maker is installed, the tire pres- sure warning system may not operate properly.

361

5-2. Steps to take in an emergency If you have a flat tire

Remove the flat tire and replace it with the spare provided. n Before jacking up the vehicle

l Stop the vehicle on a hard, flat surface. l Set the parking brake. l Shift the shift lever to P (automatic transmission) or R (manual

transmission).

l Stop the engine. l Turn on the emergency flashers.

n Location of the spare tire, jack and tools

Jack handle

Wheel nut wrench

Jack

Spare tire

362

Taking out the jack

STEP 1

5-2. Steps to take in an emergency

Turn the knobs to the “UNLOCK” position and remove the deck board.

STEP 2

Remove the hook.

363

Turn the knobs to the “UNLOCK” position and remove the deck boards.

Loosen the center fastener that secures the spare tire.

5-2. Steps to take in an emergency

Taking out the spare tire

STEP 1

STEP 2

364

5-2. Steps to take in an emergency

Replacing a flat tire

STEP 1

Chock the tires.

Flat tire

Wheel

chock posi-

tions

STEP 2

Front

Rear

Left- hand side

Right- hand side

Left- hand side

Right- hand side

Behind the rear right- hand side tire Behind the rear left- hand side tire In front of the front right-hand side tire In front of the front left-hand side tire

Vehicles with a steel wheel, remove the wheel ornament using the wrench.

To protect the wheel ornament, place a rag between the wrench and the wheel ornament, as shown in the illustration.

365

Slightly loosen the wheel nuts (one turn).

Turn the tire jack portion “A” by hand until the notch of the jack is in contact with the jack point.

The jack point guides are located under the rocker panel. They indicate the jack point positions.

5-2. Steps to take in an emergency

STEP 3

STEP 4

366

STEP 5

STEP 6

5-2. Steps to take in an emergency

Raise the vehicle until the tire is slightly raised off the ground.

Remove all the wheel nuts and the tire.

When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface.

367

5-2. Steps to take in an emergency

Installing the tire

STEP 1

Remove any dirt or foreign mat- ter from the wheel contact sur- face.

If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle.

STEP 2

Install the tire and loosely tighten each wheel nut by hand by approximately the same amount.

Replacing a steel wheel with a compact spare tire

Tapered portion

Tighten the nuts until the tapered portion comes into loose contact with the disc wheel sheet.

Disc wheel sheet

Replacing an aluminum wheel with a compact spare tire

Tapered portion

Tighten the nuts until the tapered portion comes into loose contact with the disc wheel sheet.

Disc wheel sheet

368

5-2. Steps to take in an emergency

STEP 3

Lower the vehicle.

STEP 4

Firmly tighten each nut two or three times in the order shown in the illustration.

Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)

STEP 5

Stow the flat tire, tire jack and all tools.

Stowing the flat tire

STEP 1

Vehicles with aluminum wheel: Before stowing tire, remove the center wheel orna- ment by pushing the reveres side.

from

the

flat

369

5-2. Steps to take in an emergency

STEP 2

STEP 3

STEP 4

STEP 5

370

Put the flat tire on the deck boards with the outer side of the wheel facing up. Hook the belt clips closest to the buckles onto the front cargo hooks.

Pass the belts through the center hole of the wheel.

Hook the other side of the clips of the belts to the rear hooks.

Position the tire edge against the rear center end of the luggage compartment.

5-2. Steps to take in an emergency

STEP 6

Pull the ends of the belts to secure the tire.

n The compact spare tire

l The compact spare tire is identified by the label “TEMPORARY USE

ONLY” on the tire sidewall. Use the compact spare tire temporarily only in an emergency.

l Make sure to check the tire pressure of the compact spare tire. (→P.

400)

n If you have a flat front tire on a road covered with snow or ice

Install the compact spare tire on the rear of the vehicle. Perform the fol- lowing steps and fit tire chains to the front tires. STEP 1

Replace a rear tire with the compact spare tire. Replace the flat front tire with the tire removed from the rear of the vehicle. Fit tire chains to the front tires.

STEP 2

STEP 3

n After completing the tire change (vehicles with tire pressure warn-

ing system) The tire pressure warning system must be reset. (→P. 304)

n When using the compact spare tire

As the compact spare tire is not equipped with the tire pressure warning valve and transmitter, low inflation pressure of the spare tire will not be warned. Also, if you replace the compact spare tire after the tire pressure warning light comes on, the light remains on.

371

5-2. Steps to take in an emergency

CAUTION

n Using the tire jack

Improper use of the tire jack may lead to death or injuries due to the vehicle suddenly falling off the jack. l Do not use the tire jack for any purpose other than replacing tires or

installing and removing tire chains.

l Only use the tire jack that comes with this vehicle for replacing a flat

tire. Do not use it on other vehicles, and do not use other tire jacks for replacing tires on this vehicle.

l Always check that the tire jack is securely set to the jack point. l Do not put any part of your body under the vehicle while it is supported

by a jack.

l Do not start or run the engine while your vehicle is supported by the

jack.

l Do not raise the vehicle while someone is in it. l When raising the vehicle, do not put an object on or under the jack. l Do not raise the vehicle to a height greater than that required to

replace the tire.

l Use a jack stand if it is necessary to get under the vehicle. Take particular care when lowering the vehicle to ensure that no one working on or near the vehicle will be injured.

372

5-2. Steps to take in an emergency

CAUTION

n Replacing a flat tire

Observe the following precautions to reduce the risk of death or serious injury: l Never use oil or grease on the wheel bolts or wheel nuts.

The oil or grease can cause the wheel nuts to loosen, causing a seri- ous accident. Remove any oil or grease on the wheel bolts or wheel nuts.

l Have the wheel nuts tightened with a torque wrench to 76 ft•lbf (103

N•m, 10.5 kgf•m) as soon as possible after changing wheels. Failure to follow these precautions could cause the nuts to loosen and the wheel may fall off, which could lead to an accident causing death or serious injury.

n When using the compact spare tire

l Remember that your compact spare tire is specifically designed for use with your vehicle. Do not use your compact spare tire on another vehicle.

l Do not use two compact spare tires simultaneously. l Replace the compact spare tire with a standard tire as soon as possi-

ble.

l Avoid sudden acceleration, deceleration and braking, as well as sharp

cornering.

n Speed limit when using the compact spare tire

Do not drive at speeds in excess of 50 mph (80 km/h) when a compact spare tire is installed on the vehicle. The compact spare tire is not designed for driving at high speeds. Failing to observe this precaution may lead to an accident causing death or seri- ous injury.

373

5-2. Steps to take in an emergency

CAUTION

n When the spare tire is attached

The vehicle speed may not be correctly detected, and the following sys- tems may not operate correctly: l ABS & Brake assist l VSC (if equipped) l TRAC (if equipped) l Navigation system (if equipped) Also, not only can the following system not be utilized fully, it may actu- ally negatively effect the drive-train components: l Active torque control 4WD system (if equipped)

374

5-2. Steps to take in an emergency

NOTICE

n Do not drive the vehicle with a flat tire

Do not continue driving with a flat tire. Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair.

n Be careful when driving over bumps with the compact spare tire

installed on the vehicle The vehicle becomes lower when driving with the compact spare tire compared to when driving with standard tires. Be careful when driving over uneven road surfaces.

n Driving with tire chains and the compact spare tire

Do not fit tire chains to the compact spare tire. Tire chains may damage the vehicle body and adversely affect driving performance.

n When replacing the tires

When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly. n To avoid damaging the tire pressure warning valves and transmit-

ters Do not use liquid sealants on flat tires.

375

5-2. Steps to take in an emergency If the engine will not start

If the engine still does not start after following the correct starting procedure (→P. 106) or releasing the steering lock (→P. 108), confirm the following points. n The engine will not start even when the starter motor oper-

ates normally. One of the following may be the cause of the problem. l There may not be sufficient fuel in the vehicle’s tank.

Refuel the vehicle.

l The engine may be flooded.

Try to restart the engine once more following correct starting procedures. (→P. 106)

l There may be a malfunction in the engine immobilizer system.

(→P. 60)

n The starter motor turns over slowly, the interior lights and headlights are dim, or the horn does not sound or sounds at a low volume. One of the following may be the cause of the problem. l The battery may be discharged. (→P. 379) l The battery terminal connections may be loose or corroded.

n The starter motor does not turn over, the interior lights and

headlights do not turn on, or the horn does not sound. One of the following may be the cause of the problem. l One or both of the battery terminals may be disconnected. l The battery may be discharged. (→P. 379)

Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown.

376

5-2. Steps to take in an emergency If the shift lever cannot be shifted from P (automatic transmission)

If the shift lever cannot be shifted with your foot on the brake, there may be a problem with the shift lock system (a system to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted. STEP 1

Set the parking brake. Turn the engine switch to the “ACC” position. Depress the brake pedal.

STEP 2

STEP 3

STEP 4

STEP 5

Pry the cover up with a flat- head screwdriver or equiva- lent.

Press the shift lock override button.

The shift lever can be shifted while the button is pressed.

377

5-2. Steps to take in an emergency If you lose your keys

New genuine keys can be made by your Toyota dealer. Bring a mas- ter key and the key number stamped on the key number plate.

378

5-2. Steps to take in an emergency If the battery is discharged

The following procedures may be used to start the engine if the vehi- cle's battery is discharged. You can call your Toyota dealer or qualified repair shop. If you have a set of jumper (or booster) cables and a second vehi- cle with a 12-volt battery, you can jump start your Toyota following the steps below.

1.8 L 4-cylinder (2ZR-FE) engine

STEP 5
STEP 1

Remove the engine cover.

Raise the rear of the engine cover to remove the two rear clips, and then raise the front of the engine cover to remove the two front clips.

STEP 2

Connecting the jumper cables

If required, remove all vent plugs from the booster battery. Lay a cloth over the open vents on the booster battery. (This helps reduce the explosion hazard, personal injuries and burns.) Positive (+) battery terminal on your vehicle

379

5-2. Steps to take in an emergency

Positive (+) battery terminal on the second vehicle Negative (-) battery terminal on the second vehicle Connect the jumper cable to ground on your vehicle as shown in the illustration.

STEP 3

STEP 4

STEP 5

Start the engine of the second vehicle. Increase the engine speed slightly and maintain at that level for approximately 5
minutes to recharge the battery of your vehicle. Maintain the engine speed of the second vehicle, and turn the engine switch to the “ON” position then start the vehi- cle's engine. Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were con- nected.

Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible.

380

5-2. Steps to take in an emergency

2.4 L 4-cylinder (2AZ-FE) engine

STEP 1

Connecting the jumper cables

If required, remove all vent plugs from the booster battery. Lay a cloth over the open vents on the booster battery. (This helps reduce the explosion hazard, personal injuries and burns.) Positive (+) battery terminal on your vehicle Positive (+) battery terminal on the second vehicle Negative (-) battery terminal on the second vehicle Connect the jumper cable to ground on your vehicle as shown in the illustration.

STEP 2

STEP 3

Start the engine of the second vehicle. Increase the engine speed slightly and maintain at that level for approximately 5
minutes to recharge the battery of your vehicle. Maintain the engine speed of the second vehicle, and turn the engine switch to the “ON” position then start the vehi- cle's engine.

381

5-2. Steps to take in an emergency

STEP 4

Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order in which they were con- nected.

Once the engine starts, have the vehicle checked at your Toyota dealer as soon as possible.

n Avoiding a discharged battery

l Turn off the headlights and the audio system while the engine is turned

off.

l Turn off any unnecessary electrical components when the vehicle is run- ning at a low speed for an extended period, such as in heavy traffic, etc.

n When the battery is removed or discharged

The tire pressure warning system must be initialized. (→P. 304)

382

5-2. Steps to take in an emergency

CAUTION

n Avoiding battery fires or explosions

Observe the following precautions to prevent accidentally igniting the flam- mable gas that may be emitted from the battery. l Make sure the jumper cable is connected to the correct terminal and that it is not unintentionally in contact with any part other than the intended termi- nal.

l Do not allow the jumper cables to come into contact with the “+” and “-” ter-

minals.

l Do not smoke, use matches, cigarette lighters or allow open flame near

the battery.

n Battery precautions

The battery contains poisonous and corrosive acidic electrolyte, while related parts contain lead and lead compounds. Observe the following pre- cautions when handling the battery. l When working with the battery, always wear safety glasses and take care not to allow any battery fluids (acid) to come into contact with skin, clothing or the vehicle body.

l Do not lean over the battery.

In the event that battery fluid comes into contact with the skin or eyes, immediately wash the affected area with water and seek medical attention. Place a wet sponge or cloth over the affected area until medical attention can be received.

l Always wash your hands after handling the battery support, terminals, and

other battery-related parts.

l Do not allow children near the battery.

383

5-2. Steps to take in an emergency

NOTICE

n To prevent damage to the vehicle

Do not pull- or push-start the vehicle, because the catalytic converter may overheat and become a fire hazard.

n When handling jumper cables

Be careful that the jumper cables do not become tangled in the cooling fans or any of the belts when connecting or disconnecting them.

n When attaching the engine cover

Ensure that the rubber grommets remain attached to the engine cover. If the grommet is attached to the bolts, transfer grommets to the engine cover.

384

5-2. Steps to take in an emergency If your vehicle overheats

If your engine overheats: STEP 1

Stop the vehicle in a safe place and turn off the air condi- tioning system. Check to see if steam is coming out from under the hood. If you see steam:

STEP 2

Stop the engine. Wait until the steam subsides, and then carefully lift the hood. If you do not see steam:

Leave the engine running and carefully lift the hood.

STEP 3

Check to see if the cooling fans are operating. If the fans are operating:

Wait until the temperature of the engine (shown on the instrument cluster) begins to fall and then stop the engine.

If the fans are not operating:

Stop the engine and call your Toyota dealer.

STEP 5
STEP 4

After the engine has cooled down sufficiently, check the engine coolant level and inspect the radiator core (radi- ator) for any leaks.

385

5-2. Steps to take in an emergency

STEP 5

Add engine coolant if neces- sary.

Water can be used in an emer- gency is unavailable. (→P. 396)

if engine coolant

Have the vehicle checked at the nearest Toyota dealer as soon as possible.

n Overheating

If you observe the following, your vehicle may be overheating. l The engine coolant temperature gauge enters the red zone or a loss of

power is experienced.

l Steam is coming from under the hood.

CAUTION

n To prevent an accident or injury when inspecting under the hood of

your vehicle l Keep hands and clothing away from the fan and other belts while the

engine is running.

l Do not loosen the coolant reservoir cap while the engine and radiator are

hot. Serious injury, such as burns, may result from hot coolant and steam released under pressure.

386

5-2. Steps to take in an emergency

NOTICE

n When adding engine coolant

Wait until the engine has cooled down before adding engine coolant. When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine.

387

5-2. Steps to take in an emergency If the vehicle becomes stuck

Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. STEP 1

Stop the engine. Set the parking brake and put the shift lever in P (automatic transmission) or N (manual transmis- sion). Remove the mud, snow, or sand from around the stuck tire. Place wood, stones or some other material to help provide traction under the tires. Restart the engine. Shift the shift lever to the D or R position (automatic trans- mission) or 1 or R position (manual transmission) and care- fully apply the accelerator to free the vehicle.

STEP 2

STEP 3

STEP 4

STEP 5

CAUTION

n When attempting to free a stuck vehicle

If you choose to rock the vehicle back and forth to free it, make sure the sur- rounding area is clear, to avoid striking other vehicles, objects or persons. The vehicle may also lunge forward or lunge back suddenly as it becomes free. Use extreme caution.

n When shifting the shift lever

For vehicles with an automatic transmission, be careful not to shift the shift lever with the accelerator pedal depressed. This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

NOTICE

n To avoid damaging the transmission and other components

l Avoid spinning the wheels and do not rev the engine.

If the vehicle remains stuck after trying these procedures, the vehicle may require towing to be freed.

388

6-1. Specifications Maintenance data (fuel, oil level, etc.)

Dimensions and weights

Overall length

Overall width

Overall height

Wheelbase

Tread

171.9 in. (4365 mm)*1
173.0 in. (4395 mm)*2
69.5 in (1765 mm) 61.0 in (1550 mm)*3
61.4 in (1560 mm)*4
102.4 in (2600 mm) 59.8 in (1519 mm) 59.9 in (1522 mm)

Front Rear

850 lb. (385 kg)

Vehicle capacity weight (Occupants + luggage) Towing capacity (Trailer weight + cargo weight) *1: Vehicles with 1.8 L 4-cylinder (2ZR-FE) engine and vehicles with AWD

1500 lb. (680 kg)

model

*2: Vehicles with 2.4 L 4-cylinder (2AZ-FE) engine of 2WD model *3: Vehicles without double wishbone rear suspension *4: Vehicles with double wishbone rear suspension

390

6-1. Specifications

Vehicle identification

n Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle.

This number is stamped on the top left of the instrument panel.

This number is stamped under the front passenger seat.

This number is also on the certifi- cation label on the driver’s side center pillar.

391

6-1. Specifications

n Engine number The engine number is stamped on the engine block as shown.

1.8 L 4-cylinder (2ZR-FE) engine

2.4 L 4-cylinder (2AZ-FE) engine

392

6-1. Specifications

Engine

1.8 L 4-cylinder (2ZR-FE) engine

Model

Type

Bore and stroke

2ZR-FE engine 4 cylinder in line, 4 cycle, gasoline 3.17 × 3.48 in. (80.5 × 88.3 mm) 109.7 cu.in. (1798 cm3) 143 ± 22 lb.

Displacement Drive belt tension* Valve clearance (engine cold) Intake Exhaust *: Drive belt tension measured with Borroughs drive belt tension gauge No.

Automatic adjustment

BT-33-73F (used belt), lb.

393

6-1. Specifications

2.4 L 4-cylinder (2AZ-FE) engine

Model

Type

Bore and stroke

Displacement Drive belt tension Valve clearance (engine cold) Intake

Exhaust

Fuel

2AZ-FE engine 4 cylinder in line, 4 cycle, gasoline 3.48 × 3.78 in. (88.5 × 96.0 mm) 144.1 cu.in. (2362 cm3) Automatic adjustment

0.007 ⎯ 0.011 in. (0.19 ⎯ 0.29 mm) 0.015 ⎯ 0.019 in. (0.38 ⎯ 0.48 mm)

Fuel type Octane rating Fuel tank capacity

Unleaded gasoline only 87 (Research Octane Number 91) or higher 13.2 gal. (50 L, 10.9 Imp.gal.)

394

Lubrication system

Oil capacity (drain and refill)

With filter

Without filter

Oil grade

Recommended oil viscosity

6-1. Specifications

1.8 L 4-cylinder (2ZR-FE) engine 4.4 qt. (4.2 L, 3.7 Imp.qt.) 2.4 L 4-cylinder (2AZ-FE) engine 4.0 qt. (3.8 L, 3.3 Imp.qt.) 1.8 L 4-cylinder (2ZR-FE) engine 4.1 qt. (3.9 L, 3.4 Imp.qt.) 2.4 L 4-cylinder (2AZ-FE) engine 3.8 qt. (3.6 L, 3.2 Imp.qt.) ILSAC multigrade engine oil Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the grade and vis- cosity shown below.

Outside temperature

0W-20 is the oil that provides the optimal level of fuel efficiency.

Oil viscosity l The 0W portion of the oil viscosity rating indicates the characteristic of the oil which allows cold startability. Oils with a lower value before the W allow for easier starting of the engine in cold weather.

l The 20 in 0W-20 indicates the oil viscosity when the oil is at its oper- ating temperature. An oil with a higher viscosity may be better suited if the vehicle is operated at high speeds, or under extreme load con- ditions.

395

6-1. Specifications

Cooling system

Capacity (Reference)

Coolant type

Ignition system

Spark plug Make

1.8 L 4-cylinder (2ZR-FE) engine 5.8 qt. (5.5 L, 4.8 Imp.qt.) 2.4 L 4-cylinder (2AZ-FE) engine 6.0 qt. (5.7 L, 5.0 Imp.qt.) Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology

Do not use plain water alone.

1.8 L 4-cylinder (2ZR-FE) engine DENSO SC20HR11
2.4 L 4-cylinder (2AZ-FE) engine DENSO SK20R11
NGK IFR6A11

Gap

0.043 in. (1.1 mm)

NOTICE

n Iridium-tipped spark plugs

Use only iridium-tipped spark plugs. Do not adjust spark plug gap.

396

6-1. Specifications

Electrical system

Battery

Open voltage at 68°F (20°C):

Charging rates

Manual transaxle

Gear oil capacity (Reference)

Gear oil type Recommended gear oil viscosity

Automatic transaxle

Fluid capacity (drain and refill)

12.6 ⎯ 12.8 V Fully charged 12.2 ⎯ 12.4 V Half charged 11.8 ⎯ 12.0 V Discharged (Voltage checked 20 minutes after the engine and all the lights turned off) 5 A max.

1.8 L 4-cylinder (2ZR-FE) engine 2.0 qt. (1.9 L, 1.7 Imp.qt.) 2.4 L 4-cylinder (2AZ-FE) engine 2.6 qt. (2.5 L, 2.2 Imp.qt.)

API GL-4

SAE 75W

1.8 L 4-cylinder (2ZR-FE) engine 2.6 qt. (2.5 L, 2.2 Imp.qt.) 2.4 L 4-cylinder (2AZ-FE) engine 3.7 qt. (3.5 L, 3.1 Imp.qt.)

Fluid type

Toyota Genuine ATF WS

397

6-1. Specifications

NOTICE

n Automatic transmission fluid type

Using automatic transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the transmission of your vehicle.

Rear differential (AWD models)

Oil capacity Oil type

Recommended oil viscosity

Transfer (AWD models)

Oil capacity Oil type

Recommended oil viscosity

Clutch

Pedal free play Fluid type

0.5 qt. (0.5 L, 0.4 Imp.qt.) Hypoid gear oil API GL-5
Above 0°F (-18°C): SAE 90
Below 0°F (-18°C): SAE 80W or 80W-90

0.8 qt. (0.8 L, 0.7 Imp.qt.) Hypoid gear oil API GL-5
Above 0°F (-18°C): SAE 90
Below 0°F (-18°C): SAE 80W or 80W-90

0.2 ⎯ 0.6 in. (5 ⎯ 15 mm) SAE J1703 or FMVSS No.116 DOT 3

398

6-1. Specifications

Brakes

Pedal clearance*1

1.8 L 4-cylinder (2ZR-FE) engine • With vehicle stability control: 3.4 in. (87 mm) • Without vehicle stability control: 3.2 in. (81 mm) 2.4 L 4-cylinder (2AZ-FE) engine • AWD models: 3.4 in. (87 mm) • Vehicles with P215/45R18 tires: 3.4 in. (87 mm) • Vehicles with tires other than the above: 3.3 in. (85 mm) 0.04 ⎯ 0.24 in. (1 ⎯ 6 mm) 0.04 in. (1.0 mm) 0.04 in. (1.0 mm) 6 ⎯ 9 clicks SAE J1703 or FMVSS No.116 DOT 3

Pedal free play Brake pad wear limit Parking brake lining wear limit*2
Parking brake lever travel*3
Fluid type *1: Minimum pedal clearance when depressed with a force of 66 lbf (294 N, 30

kgf) while the engine is running

*2: 2.4 L 4-cylinder (2AZ-FE) engine with 18-inch tires or AWD models *3: Parking brake lever travel when pulled up with a force of 44 lbf (200 N, 20

kgf)

399

6-1. Specifications

Steering

Free play

Tires and wheels

Type A

Less than 1.2 in. (30 mm)

Tire size Tire inflation pressure (Recommended cold tire inflation pressure) Wheel size Wheel nut torque

P205/55R16 89H, T135/70R16 100M Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) 16 × 6 1/2 J, 16 × 4T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

Type B

Tire size Tire inflation pressure (Recommended cold tire inflation pressure) Wheel size Wheel nut torque

P205/55R16 89H, T135/80R16 101M Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) 16 × 6 1/2 J, 16 × 4T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

400

6-1. Specifications

Type C

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

Wheel size Wheel nut torque

Type D

P205/55R16 89H, T135/70R17 102M

2WD models Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) AWD models Front: 35 psi (240 kPa, 2.4 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar)

16 × 6 1/2 J, 17 × 4T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

Tire size Tire inflation pressure (Recommended cold tire inflation pressure) Wheel size Wheel nut torque

P215/45R17 87W, T135/70R16 100M Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) 17 × 7J, 16 × 4T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

401

6-1. Specifications

Type E

Tire size Tire inflation pressure (Recommended cold tire inflation pressure) Wheel size Wheel nut torque

P215/45R17 87W, T135/80R16 101M Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) 17 × 7 J, 16 × 4T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

Type F

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

P215/45R17 87W, T135/70R17 102M

2WD models Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) AWD models Front: 35 psi (240 kPa, 2.4 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar)

Wheel size Wheel nut torque

17 × 7 J, 17× 4T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

402

6-1. Specifications

Type G

Tire size Tire inflation pressure (Recommended cold tire inflation pressure) Wheel size Wheel nut torque

P215/45R18 89W, T135/70R17 102M Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar) Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) 18 × 7 J, 17 × 4T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

403

6-1. Specifications

Light bulbs

Light Bulbs

Bulb No.

Headlights Low beam High beam Front turn signal/park- ing and front side marker lights Front fog lights (if equipped) Rear turn signal lights Stop/tail and rear side marker lights License plate lights Back-up lights Personal lights Interior light

Exterior

Interior

51
60

9006
9005

3457NA

27/7

⎯

⎯

55

21

7443

21/5

⎯ 921
⎯

16
B: HB3 halogen bulbs D: Wedge base bulbs (amber) F: HB4 halogen bulbs

⎯

Type

A: H11 halogen bulbs C: Wedge base bulbs (clear) E: Double end bulbs

404

6-1. Specifications Fuel information

You must only use unleaded gasoline in your vehicle. Unleaded gasoline with an Octane Rating of 87 (Research Octane Number 91) or higher is required for optimum engine performance. At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada.

n Fuel tank opening for unleaded gasoline

To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.

n If your engine knocks

l Consult your Toyota dealer. l You may occasionally notice light knocking for a short time while acceler-

ating or driving uphill. This is normal and there is no need for concern.

n Gasoline quality

In very few cases, driveability problems may be caused by the brand of gas- oline you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer.

n Gasoline quality standards

l Automotive manufacturers in the U.S., the Europe and Japan have developed a specification for fuel quality called World-Wide Fuel Charter (WWFC) that is expected to be applied worldwide.

l The WWFC consists of four categories that are based on required emis-

sion levels. In the U.S., category 4 has been adopted.

l The WWFC improves air quality by lowering emissions in vehicle fleets,

and improves customer satisfaction through better performance.

405