’08 MATRIX_U (L/O 0706)
SECTION 1− 1
OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview Instrument cluster overview Indicator symbols on the instrument panel
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Instrument panel overview (cid:1)View A
1. Side defroster outlets 2. Side vents 3. Instrument cluster 4. Center vents 5. Personal lights 6. Electric moon roof switches and
personal light
7. Power door lock switches 8. Power window switches 9. Glove box 10. Portable ashtray 11. Cup holders 12. Power outlet (12 VDC) 13. Parking brake lever 14. Auxiliary boxes 15. Automatic transmission selector lever
or manual transmission gear shift lever
16. Hood lock release lever 17. Window lock switch
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
(cid:1)View B
1. Power rear view mirror control switches 2. Instrument panel light control dial 3. Headlight, turn signal and front fog
light switches
4. Wiper and washer switches 5. Air conditioning controls 6. Rear window defogger switch 7. Emergency flasher switch 8. Clock 9. Front passenger’s seat belt reminder
light/front passenger occupant classification indicator light
10. Audio system 11. Auxiliary box or power outlet (115 VAC) 12. Power outlet (12 VDC) or cigarette
lighter
13. Ignition switch 14. Cruise control switch 15. Tilt steering lock release lever 16. “TRAC OFF” (traction control system
off) switch
17. Engine immobilizer system/Toyota vehicle intrusion protection system indicator light
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
18. Tire pressure warning system reset
switch
19. Glass hatch opener switch
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Instrument cluster overview
1. Tachometer 2. Service reminder indicators and
indicator lights
3. Speedometer
4. Fuel gauge 5. Low fuel level warning light 6. Engine coolant temperature gauge
7. Trip meter reset knob 8. Odometer, two trip meters and outside
temperature display
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Indicator symbols on the instrument panel
or
Brake system warning light* 1
or
Anti−lock brake system warning light* 1
Driver’s seat belt reminder light* 1
Open door warning light* 1
Front passenger’s seat belt reminder light* 1
SRS warning light* 1
Vehicle stability control system/traction control
system warning light* 1
Charging system warning light* 1
Low tire pressure warning light* 1
Low engine oil pressure warning light* 1
Low windshield washer fluid level warning light* 1
or
Malfunction indicator lamp* 1
Engine oil replacement reminder light* 1
Front passenger occupant classification indicator light
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Headlight indicator light
Tail light indicator light
Headlight high beam indicator light
Turn signal indicator lights
Overdrive−off indicator light
Slip indicator light/traction control system off indicator light
Cruise control indicator light* 2
* 1: For details, see “Service reminder indicators and warning
* 2:
buzzers” on page 105 in Section 1−6. If this light flashes, see “Cruise control” on page 133 in Section 1−7.
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
SECTION 1− 2
OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys Engine immobilizer system Wireless remote control Side doors Power windows Back door Glass hatch Toyota vehicle intrusion protection system (TVIP) Hood Fuel tank cap Electric moon roof
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
12
14
18
22
24
25
26
28
29
30
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Keys
A transponder chip for engine immobilizer system has been placed in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine.
Your vehicle is supplied with two kinds of keys. 1. Master keys (black)—
These keys work in every lock. Your Toyota dealer will need one of them to make a new key with a built−in trans- ponder chip. Since the side doors and back door can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.
2. Sub key (gray)—
This key also works in every lock. When using valet parking, leave sub key with the attendant.
the
10
NOTICE
When using a key containing a trans- ponder chip, observe the following precautions: (cid:1) When starting the engine, do not use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
(cid:1) Do not bend the key grip.
(cid:1) When starting the engine, do not use the key with other transponder keys around (including keys of oth- er vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after remov- ing other transponder keys (includ- ing keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.
(cid:1) Do not cover the key grip with any material that cuts off electromagnet- ic waves.
(cid:1) Do not knock the key hard against
other objects.
(cid:1) Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under direct sunlight.
(cid:1) Do not put the key in water or
wash it in an ultrasonic washer.
(cid:1) Do not use the key with electromag-
netic materials.
11
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Engine immobilizer system
KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend writing down the key num- ber and storing it in a safe place.
12
Without Toyota vehicle intrusion protec- tion system
in
immobilizer system
The engine is a theft prevention system. When you in- sert the key in the ignition switch, the transponder chip the key’s head transmits an electronic code to the ve- hicle. The engine will start only when the electronic code in the chip corre- sponds to the registered ID code for the vehicle. Never leave the keys inside the vehicle when you leave the vehicle.
With Toyota vehicle intrusion protection system
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
indicator
light will start
The system is automatically set when the key is removed from the ignition switch. The flashing to show the system is set. If any of the following indicator conditions occurs, contact your Toyota dealer. (cid:1) The
light stays on except
when
intrusion
protection system is setting or activat-
ing.
intrusion
protection system (TVIP)” on page 26
in this Section.)
“Toyota vehicle
the Toyota
indicator
vehicle
(See
(cid:1) The indicator light does not start flash- ing when the key is removed from the ignition switch.
(cid:1) The indicator light flashes inconsistent-
ly.
Inserting the registered key in the ignition switch automatically cancels the system, which enables the engine to start. The indicator light will go off. The system is maintenance−free. For your Toyota dealer to make you a new key with built−in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you.
’08 MATRIX_U (L/O 0706)
If you make your own duplicate key, you will not be able to cancel the sys- tem or start the engine.
NOTICE
Do not modify, remove or disas- semble the engine immobilizer sys- tem. If any unauthorized changes or modifications are made, proper opera- tion of the system cannot be guaran- teed.
For vehicles sold in U.S.A.
FCC ID: MOZRI−21BTY This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.
CAUTION
Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.
13
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
For vehicles sold in Canada
Wireless remote control—
This device complies with RSS−210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.
interference,
including
1. “LOCK” switch 2. “UNLOCK” switch 3. “HATCH GLASS” switch 4. “PANIC” switch
The wireless remote control system is
designed to lock or unlock all the side
doors and back door, open the glass
hatch or activate the “PANIC” mode
from a distance within approximately 1
m (3 ft.) of the vehicle.
When you operate any switch, push
slowly and securely.
The wireless remote control transmitter is
an electronic component. Observe the fol-
lowing instructions in order not to cause
damage to the transmitter.
(cid:1) Do not leave the transmitter in places
the temperature becomes high
where such as on the dashboard.
it
(cid:1) Do not disassemble it. (cid:1) Avoid knocking
it hard against other
objects or dropping it.
(cid:1) Avoid putting it in water. You can use up to 4 wireless remote con- trol the same vehicle. Contact your Toyota dealer for detailed information.
transmitters
for
14
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
—Locking and unlocking doors
If the wireless remote control transmitter does not actuate the doors or alarm, or operate from a normal distance: (cid:1) Check for closeness to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.
(cid:1) The battery may have been consumed. Check the battery in the transmitter. To replace the battery, see “—Replacing transmitter battery” on page 17.
If you lose your transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an acci- dent. (See “If you lose your wireless re- mote control transmitter” on page 251 in Section 4.)
This complies with Part 15 of the FCC rules. Operation is subject to the follow- ing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.
Locking operation
Unlocking operation
this
time,
To lock and unlock all the side doors and back door, push the switches of the transmitter slowly and securely. To lock: Push the “LOCK” switch. All the side doors and back door are locked si- multaneously. At turn signal lights flash once. Check to see that all the side doors and back door are securely locked. If any of side doors or back door is not securely closed, or if the key is in the ignition switch, locking cannot be per- formed by the “LOCK” switch. “UNLOCK” switch To unlock: Push once to unlock the driver’s door alone. Pushing the switch twice within 3 seconds unlocks all the side doors and back door simultaneously. At turn signal lights flash twice. When the doors are unlocked, the interior lights come on and remain on for about 15 seconds before fading out. (For further information, see “Interior lights” on page 95 in Section 1−5.) You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the side doors and back door will be automati- cally locked again.
time,
this
the
15
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking opera- tion is not repeated. Release the switch and then push again.
—Opening glass hatch
—Activating panic mode
the glass hatch, push
To open the “HATCH GLASS” switch of the transmit- ter for 1 second. If the ignition key is in the “ON” position, the glass hatch cannot be opened by the “HATCH GLASS” switch. See “Glass hatch” on page 25 Section.
this
in
flashes
intermittently and
Pushing the “PANIC” switch blows the horn the headlights, turn signal lights and interi- or lights. The “PANIC” switch is used to deter ve- hicle theft when you witness anyone at- tempting into or damage your vehicle. The alarm will last for one minute. To stop alarm midway, do the following: (cid:1) Push any of the switch on the wireless
to break
16
remote control transmitter.
(cid:1) Turn the ignition key from the “LOCK”
to “ON” position.
The “PANIC” mode does not work when the ignition key is in the “ON” position.
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
—Replacing transmitter battery For replacement, use a CR2032 lithium battery or equivalent.
CAUTION
Special care should be taken to pre- vent small children from swallowing the removed transmitter battery or components.
NOTICE
(cid:1) During replacing the transmitter battery, do not push the “LOCK”, “UNLOCK” and “HATCH GLASS” switches many times.
(cid:1) When replacing the transmitter bat- tery, be careful not to lose the com- ponents.
(cid:1) Replace only with the same or equivalent type recommended by a Toyota dealer.
(cid:1) Dispose of used batteries according
to the local laws.
Replace the transmitter battery by follow- ing these procedures:
1. Using a coin or equivalent, open the
2. Remove the discharged transmitter bat-
transmitter case.
tery.
17
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Side doors—
NOTICE
(cid:1) Do not bend the terminals. (cid:1) Make sure the positive side and negative side of the transmitter bat- tery are faced correctly.
(cid:1) Do not replace the battery with wet hands. Water may cause unexpected rust.
(cid:1) Do not touch or move any compo- nents inside the transmitter, or it may interfere with proper operation. (cid:1) Be careful not to bend the electrode when inserting the transmitter bat- tery and that dust or oils do not adhere to the transmitter case.
(cid:1) Close the transmitter case securely.
LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. Vehicles with power door lock system— All the side doors and back door lock and unlock simultaneously with either front door. In the driver’s door lock, turning the key once will unlock the driver’s door and twice in succession will unlock all the side doors and back door simultaneously.
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
3. Put in a new transmitter battery with
positive (+) side up.
Close the transmitter case securely. After replacing the battery, check that the transmitter operates properly. If the trans- mitter still does not operate properly, con- tact your Toyota dealer.
18
When the doors are unlocked, the interior lights come on and remain on for about 15 seconds before fading out. (For further information, see “Interior lights” on page 95 in Section 1−5.)
’08 MATRIX_U (L/O 0706)
CAUTION
Do not pull the inside handle of the front doors while driving. The doors will open and an accident may occur. Toyota strongly recommends that all children be placed in the rear seat of the vehicle.
Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the ve- hicle. Vehicles with power door lock system— Doors cannot be locked when either front door is open and the key is in the igni- tion.
LOCKING AND UNLOCKING WITH INSIDE LOCK KNOB Move the lock knob. To lock: Push the knob forward. To unlock: Pull the knob backward. The front doors can be opened by pulling the inside handle even if the lock knobs are in the locked position.
19
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
(cid:1) Unlock the driver’s door or front pas- lock senger’s door with knob, and the side doors and back door with the power door lock switch.
then unlock all
inside
the
lock: Push the switch down on the
LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To front side. To unlock: Push the switch down on the rear side. All the side doors and back door lock or unlock simultaneously. If you do either of the followings, no side door or back door can be unlocked with the power door lock switch. (cid:1) Lock all the side doors and back door with the key or wireless remote control transmitter when all the side doors and back door are closed.
(cid:1) Open the driver’s door or front passen- ger’s door and move the inside lock knobs of both front doors to the lock position, then close the front doors.
The power door lock switch can be reset in the following ways. (cid:1) Turn the ignition key to “ON”. (cid:1) Unlock all
the side doors and back door with the key or wireless remote control transmitter.
Driver’s side
Passenger’s side
20
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
CAUTION
Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle in an accident. It also helps pre- vent the doors from being opened unintentionally.
—Automatic door locking and unlocking functions Vehicles with automatic transmission and power door lock system—You can the select automatic unlocking functions. (cid:1) Mode 1—Automatic
following modes of locking
locking
linked
and
the
with the shift position All the side doors and back door are automatically locked when the selector lever is moved out of the “P” position with the “ON” position and all the doors are closed.
ignition switch
the
in
to
the
lock
lever
the “LOCK”
REAR DOOR CHILD−PROTECTORS Move position as shown on the label. When the child−protector is locked, you cannot open the rear door by the inside door handle. We recommend using this feature whenever small children are in the vehicle.
(cid:1) Mode 2—Functions cancelled
function—All
Automatic door locking and unlocking functions do not activate in this mode. (cid:1) Mode 3—Automatic locking and un- locking linked with the shift position Locking the side doors and back door are automatically locked when the selector lever is moved out of ignition switch in the “ON” position and all the doors are closed. Unlocking function—All the side doors and back door are automatically un- locked when is moved to the “P” position with the igni- tion switch in the “ON” position.
the “P” position with
the selector
lever
the
21
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Power windows
4. Within 5 seconds after
ignition
switch is turned to the “ON” position,
push and hold
lock
switch on the front side for about 5
seconds.
the power door
the
5. The interior light will flash to indicate
that the mode has been changed.
The flashing of the interior light indicates the mode which has been selected. (cid:1) Flashing function
once,
the
has
Window lock switch
changed to mode 1.
(cid:1) Flashing
twice,
the
function
has
changed to mode 2.
(cid:1) Flashing three times, the function has
changed to mode 3.
(cid:1) Flashing four times, the function has
changed to mode 4.
If the battery is disconnected or run down, the mode may change. Set the desired mode by following the above procedures.
Driver’s door
Front
function—All
the “P” position with
(cid:1) Mode 4—Automatic locking and un- locking linked with the shift position and ignition switch Locking the side doors and back door are automatically locked when the selector lever is moved out of ignition switch in the “ON” position and all the doors are closed. Unlocking function—All the side doors and back door are automatically un- locked when is turned from the “ON” position to the “ACC” or “LOCK” position.
ignition switch
the
the
CHANGING THE MODE The mode toggles through from mode 1 to mode 4. To change the mode, do the following: 1. Set
the “DOOR” position. (See “Interior lights” on page 95 in Section 1−5.)
light switch
interior
the
to
2. Shift
the selector
the “P” position and close all the side doors and back door.
lever
into
3. Turn
the ignition switch to the “ON”
position.
22
Rear
Passengers’ doors
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
The windows can be operated with the switch on each side door. The passen- gers’ windows can also be controlled by the switches on the driver’s door. The power windows work when the ignition switch is in the “ON” position. Normal operation: The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, the passengers’ windows cannot be operated. Automatic operation (to open the driv- er’s window): Push the switch completely down and then release it. The window will fully open. To stop the window partway, lightly pull the switch up and then release it.
’08 MATRIX_U (L/O 0706)
CAUTION
To avoid death or serious personal injury, you must do the following. (cid:1) Before you close the power win- dows, always make sure there is nobody around the power windows. You must also make sure the heads, hands and other parts of the bodies of all occupants are kept completely If someone’s neck, head or hands get caught it could result in death or serious in- jury. When anyone closes the power windows, make sure he or she op- erates the windows safely.
in a closing window,
the vehicle.
inside
(cid:1) Be sure to remove the ignition key
when you leave your vehicle.
(cid:1) Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, he/she could use the power window switches and get in a window. Unat- tended person (particularly a small child) can be involved in a serious accident.
trapped
(cid:1) When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.
them
23
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Back door
CAUTION
Keep the back door and glass hatch closed while driving. This not only keeps the luggage from being thrown out but also prevents exhaust gases from entering the vehicle.
NOTICE
To prevent damage to the back door and glass hatch dampers, do not ap- ply any force, paint or let any other foreign matter on them.
When closing the back door, the inside
handle can be used to make the reach
easier.
To close the back door, lower it and press
down on it. After closing the back door,
try pulling it up to make sure it is secure-
ly closed.
See “—Stowage precautions” on page 211
in Section 2 for precautions when loading
luggage.
LOCKING AND UNLOCKING WITH KEY
Insert the key into the keyhole and turn
it.
To lock: Turn the key clockwise.
If you turn the key fully clockwise, the
glass hatch will open. (See “Glass hatch”
on page 25 in this Section.)
To unlock: Turn the key counterclockwise.
To open the back door, pull the lock re-
lease lever.
Operating the power door lock switch or
wireless remote control transmitter simul-
taneously locks or unlocks the back door.
(See “—Locking and unlocking doors” on
page 15 and “Side doors” on page 18 in
this Section.)
24
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Glass hatch
the
followings,
If you do either of the glass hatch cannot be opened with the glass hatch opener switch. (cid:1) Lock all the side doors and back door with the key or wireless remote control transmitter when the front doors are closed.
(cid:1) Open the driver’s door or front passen- ger’s door and move the inside lock knobs of both front doors to the lock position, then close the front doors.
The glass hatch opener switch can be reset in the following ways. (cid:1) Turn the ignition key to “ON”. (cid:1) Unlock all the doors with the key or
wireless remote control transmitter.
(cid:1) Unlock the driver’s door or front pas- lock the doors
senger’s door with knob, and then unlock all with the power door lock switch.
inside
the
OPENING THE GLASS HATCH WITH THE KEY Insert the key into the keyhole and turn it fully clockwise (one step further than the back door locking position). The glass hatch can be opened with the wireless remote control transmitter. See “—Opening glass hatch” on page 16 in this Section.
OPENING THE GLASS HATCH WITH THE GLASS HATCH OPENER SWITCH Push when the vehicle is stopped.
the glass hatch opener switch
CAUTION
Do not open the glass hatch while the vehicle is moving.
25
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
CLOSING THE GLASS HATCH
Lower the glass hatch and push the
lower center of it until it is locked.
When you open the back door with the
glass hatch opened, the glass hatch will
be closed. After closing the back door,
you should check
the glass hatch fully
closed.
See “—Stowage precautions” on page 211
in Section 2 for precautions when loading
luggage.
CAUTION
Keep the back door and glass hatch closed while driving. This not only keeps the luggage from being thrown out but also prevents exhaust gases from entering the vehicle.
NOTICE
To prevent damage to the back door and glass hatch dampers, do not ap- ply any force, paint or let any other foreign matter on them.
26
’08 MATRIX_U (L/O 0706)
Toyota vehicle intrusion protection system (TVIP)
is a
theft deterrent system.
TVIP If someone attempts to damage or break into your vehicle, the system sounds the alarm while flashing the lights.
SETTING THE SYSTEM You can set the system as follows. 1. Remove
the key
from
the
ignition
switch.
is
removed
The indicator light will start flashing when the key ignition switch. (See “Engine immobilizer system” on page 12 for details.) 2. Have all passengers get out of
from
the
the
vehicle.
3. Close all the side doors, back door and
glass hatch securely.
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
4. Lock all the side doors and back door with the key or wireless remote control transmitter. At this time, the TVIP indi- cator light comes on. The system will be set in 30 seconds. When the system is set, the indicator light will start flashing again.
5. Make sure
light flashes. Then you may leave the ve- hicle.
indicator
that
the
lights. Also,
Never leave anyone in the vehicle when you set the system because unlocking from the inside activates the alarm. Activating the alarm If the system detects a threat to the it sounds the alarm for one vehicle, minute while flashing headlights and turn signal interior lights turn on when the interior light switch is in the “DOOR” position. The system detects a threat under any of the following conditions: (cid:1) Either of the front doors is unlocked by means other than the key or wireless remote control transmitter. If the key is not in the ignition switch, all the side doors and back door will be automatically locked again.
the
(cid:1) Any of the side doors, back door or
glass hatch are forcibly opened. The alarm will activate when the back door is unlocked with a key. Cancel the system before unlocking the back door. (cid:1) The side windows are tapped or bro-
ken.
(cid:1) The battery
terminal and then reconnected.
is disconnected
(cid:1) The ignition is hotwired. After one minute, the alarm automatically stops and the indicator light starts flashing again. Reactivating the alarm Once set, until you cancel the system, the system automatically resets the alarm af- ter the alarm has stopped. The alarm will activate again under the same circumstances described in “Activat- ing the alarm”. Stopping the alarm You can stop the alarm in either of the following ways: (cid:1) Unlock any of the side doors and back door with the key or wireless remote control transmitter.
(cid:1) Place the ignition switch in the “ON”
position.
CANCELLING THE SYSTEM You can cancel the system as described in “Stopping the alarm”. If you cancel the system by unlocking any of the side doors but no door is opened within 30 seconds, all the side doors and back door lock automatically and the sys- tem will be set again. TESTING THE SYSTEM You can check the system operation as follows. 1. Open all the windows. 2. Set
system as described
the
in
“SETTING THE SYSTEM”.
3. Unlock the driver’s door with the inside lock knob. The system should activate and the alarm should sound.
4. Stop the alarm as described in “Stop-
ping the alarm”.
for
to 4
5. Repeat steps 2
the other doors. (For rear side doors, unlock and then open the doors in step 3.) the system does not work properly,
If have it checked by your Toyota dealer.
27
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Hood
To open the hood: 1. Pull the hood lock release lever. The
hood will spring up slightly.
CAUTION
Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.
28
2. In front of the vehicle, pull up the the
lever and
lift
auxiliary catch hood.
3. Hold the hood open by inserting the
support rod into the slot.
To insert the support rod into the slot, move it straight up. If it is moved to the side or toward the inside of the vehicle, it may become detached. Before closing the hood, check to see that you have not forgotten any tools, rags, etc. and return its clip—this prevents rattles. Then lower the hood and make sure it locks into place. If necessary, press down gently on the front edge to lock it.
the support rod
to
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
CAUTION
After inserting the support rod into the slot, make sure the rod supports the hood securely from falling down on to your head or body.
NOTICE
Be sure to return the support rod to its clip before closing the hood. Clos- ing the hood with the support rod up could cause the hood to bend.
’08 MATRIX_U (L/O 0706)
Fuel tank cap
This indicates that the fuel filler door is on the left side of your vehicle.
1. To open the fuel filler door, pull the
lever up. When refueling, turn off the engine.
CAUTION
(cid:1) Do not smoke, cause sparks or al- flames when refueling.
low open The fumes are flammable.
(cid:1) When opening the cap, do not re- move the cap quickly. In hot weath- er, fuel under pressure could cause injury by spraying out of the filler neck is suddenly re- moved.
the cap
if
29
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Electric moon roof
CAUTION
(cid:1) Make sure the cap is installed se- in
curely to prevent fuel spillage the event of an accident.
(cid:1) Use only a genuine Toyota fuel tank cap for replacement. It is designed to regulate fuel tank pressure.
Sliding operation
Tilting operation
2. To remove the fuel tank cap, turn the cap slowly counterclockwise, then pause slightly before removing it. After removing the cap, hang it on the cap hanger.
the cap clockwise
It is not unusual to hear a slight swoosh when the cap is opened. When installing, turn till you hear a click. If the cap is not installed securely, the malfunction lamp comes on. Make sure the cap is tightened securely. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.
indicator
30
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
the
the rear
the switch on
the moon roof, use
To operate switch beside the personal light. The key must be in the “ON” position. The sun shade can be opened or closed by hand. Sliding operation— To open: Push side. The sun shade will be opened together with the roof. To close: Push the switch on the front side. As a precaution when closing, the roof stops at the half closed position before fully closing. Therefore, release the switch and then push it again to close it com- pletely. Tilting operation— To tilt up: Push the switch on the “UP” side. To lower: Push the switch on the opposite side of the “UP” side. You may stop the moon roof at any de- sired position. The roof will move while the switch is being pushed and stop when released except to slide open.
’08 MATRIX_U (L/O 0706)
CAUTION
To avoid death or serious personal injury, you must do the following. (cid:1) While the vehicle is moving, always keep the heads, hands and other parts of the bodies of all occupants away from the roof opening. Other- wise, they could be killed or seri- injured if the vehicle stops ously suddenly or in- volved in an accident.
if the vehicle
is
(cid:1) Never leave anyone (particularly a small child) alone in your vehicle, especially with the ignition key still inserted. Otherwise, he/she could use the moon roof switches and get trapped in the roof opening. Unat- tended person (particularly a small child) can be involved in a serious accident.
(cid:1) Never sit on
top of
the vehicle
around the roof opening.
(cid:1) Before you close the moon roof, always make sure there is nobody around the moon roof. You must also make sure nobody places his or her head, hands and other parts of the body in the roof opening. If someone’s neck, head or hands get caught in the closing roof, it could result injury. When anyone closes the moon roof, first make sure it is safe to do so. (cid:1) Be sure to remove the ignition key
in death or serious
when you leave your vehicle.
31
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
32
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
SECTION 1− 3
OPERATION OF INSTRUMENTS AND CONTROLS Occupant restraint systems Seats Front seats Fold−down rear seat Head restraints Seat belts SRS airbags Child restraint
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
34
38
39
40
48
67
33
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Seats While the vehicle is being driven, all ve- hicle occupants should have the seatback upright, sit well back in the seat and prop- erly wear the seat belts provided.
CAUTION
(cid:1) Do not drive the vehicle unless the occupants are properly seated. Do not allow any passengers to sit on top of a folded−down seatback, or in the luggage compartment or car- go area. Persons not properly seated and/or not properly re- strained by seat belts can be killed or severely injured in the event of emergency braking or a collision.
(cid:1) During driving, do not allow any passengers to stand up or move around between seats. Otherwise, death or severe injuries can occur in the event of emergency braking or a collision.
Front seats— —Front seat precautions Driver seat
CAUTION
The SRS driver airbag deploys with
considerable
force, and can cause
death or serious injury especially if
the driver is very close to the airbag.
The National Highway Traffic Safety
Administration (“NHTSA”) advises:
Since the risk zone for driver airbag
is the first 50—75 mm (2—3 in.) of
inflation, placing yourself 250 mm (10
in.) from your driver airbag provides
you with a clear margin of safety.
This distance is measured from the
center of the steering wheel to your
breastbone. If you sit less than 250
mm
in.) away now, you can
change your driving position in sever-
al ways:
(cid:1) Move your seat to the rear as far
as you can while still reaching the
pedals comfortably.
(10
34
(cid:1) Slightly recline
the back of
the
seat. Although vehicle designs vary,
many drivers can achieve the 250
mm (10 in.) distance, even with the
driver seat all the way forward, sim-
ply by reclining the back of the
seat somewhat. If reclining the back
of your seat makes it hard to see
the road, raise yourself by using a
firm, non−slippery cushion, or raise
the seat
if your vehicle has that
feature.
(cid:1) If your steering wheel is adjustable, tilt it downward. This points the air- bag toward your chest instead of your head and neck.
The seat should be adjusted as rec- ommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Front passenger seat
Front seats (with SRS side airbags)
CAUTION
CAUTION
The SRS front passenger airbag also deploys with considerable force, and can cause death or serious injury es- pecially if the front passenger is very close to the airbag. The front passen- ger seat should be as far from the airbag as possible with the seatback adjusted, so the front passenger sits upright.
The SRS side airbags are installed in the driver and front passenger seats. Observe the following precautions. (cid:1) Do not lean against the front door when the vehicle is in use, since the side airbag inflates with consid- erable speed and force. Otherwise, you may be killed or seriously in- jured.
(cid:1) Do not use seat accessories which cover the area where the side air- bags inflate. Such accessories may prevent the side airbags from acti- vating correctly, causing death or serious injury.
(cid:1) Do not modify or replace the seats or upholstery of front seats with side airbags. Such changes may prevent the side airbags from acti- vating correctly, disable the system or cause the side airbags to inflate accidentally, resulting in death or serious injury.
—Seat adjustment precautions
CAUTION
(cid:1) Do not adjust the seat while the vehicle is moving as the seat may unexpectedly move and cause the driver to lose control of the vehicle. (cid:1) Be careful that the seat does not
hit a passenger or luggage.
(cid:1) After adjusting the seat position, re- lease the lever and try sliding the seat forward and backward to make sure it is locked in position.
(cid:1) After adjusting the seatback, push your body back against the seat to make sure the seat in position.
locked
is
(cid:1) Do not put objects under the seats. Otherwise, the objects may interfere with the seat−lock mechanism or unexpectedly push up the seat posi- tion adjusting lever and the seat may suddenly move, causing the driver to lose control of the vehicle.
35
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
—Adjusting front seats
(cid:1) While adjusting the seat, do not put your hands under the seat or near the moving parts. Otherwise, your hands or fingers may be caught and injured.
1. SEAT POSITION ADJUSTING LEVER Hold the center of the lever and pull it up. Then slide the seat to the desired position with slight body pressure and release the lever. 2. SEAT CUSHION HEIGHT ADJUSTING
LEVER
Pull up or push down the lever. 3. SEATBACK
ANGLE
ADJUSTING
LEVER
lever up. lean back to the desired angle
Lean forward and pull the Then and release the lever.
36
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
—Fold−down front passenger’s seat
CAUTION
reclining
Avoid the seatback any more than needed. The seat belts pro- vide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply re- straint forces directly to the abdomen or your neck may contact the shoul- der belt. In the event of a frontal collision, the more the seat is re- clined, the greater the risk of death or serious injury.
1. Lower the head restraint to the low- est position and fix the seatback at the most upright lock position.
2. Pull up either seatback lock release knob beside the seatback and fold the seatback down.
CAUTION
Do not sit on or place anything on the folded seatback to avoid death or serious is moving.
injury while
the vehicle
37
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Fold−down rear seat
CAUTION
When returning the seatback to the upright position, make sure the seat- back is securely locked by pushing forward and rearward on the top of the seatback. Failure to do so will prevent seat belt from operating prop- erly.
You can use the front passenger’s seat- back as a temporary table only when the vehicle is stopped.
CAUTION
To avoid death or serious injury: (cid:1) Do not set up the seatback table
while the vehicle is moving.
(cid:1) Do not sit on the seatback table.
NOTICE
To prevent damage to the seat, avoid putting heavy loads on the temporary table.
38
Lower the head restraints to the lowest position. Pull up the lock release button and fold the seatback down. Each seatback can be folded separately. This will enlarge the luggage compartment as far as the seatbacks. See “—Stowage precautions” on page 211 in Section 2 for precautions when loading luggage.
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
’08 MATRIX_U (L/O 0706)
Head restraints
CAUTION
When returning the seatback to the upright position, observe the follow- ing precautions in order to prevent death or serious injury in a collision or sudden stop: (cid:1) Make sure the seatback is securely locked by pushing forward and rear- ward on the top of the seatback and that the red mark at the button on the top of the seatback cannot be seen. Failure to do so will pre- vent seat belt from operating prop- erly.
(cid:1) Make sure the seat belts are not twisted or caught in the seatback and are arranged the proper position and are ready to use.
in
Front
Rear
39
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
You can use the rear right side seatback as a temporary table only when the ve- hicle is stopped.
CAUTION
To avoid death or serious injury: (cid:1) Do not set up the seatback table
while the vehicle is moving.
(cid:1) Do not sit on the seatback table.
NOTICE
To prevent damage to the seat, avoid putting heavy loads on the temporary table.
’08 MATRIX_U (L/O 0706)
Do not allow any children to stand up or kneel on either rear or front seats. An unrestrained child could suffer serious in- jury or death during emergency braking or a collision. Also, do not let the child sit on your lap. Holding a child in your arms does not provide sufficient restraint. Pregnant woman. Toyota recommends the use of a seat belt. Ask your doctor for specific lap belt should be worn securely and as low as possible over the hips and not on the waist. Injured person. Toyota recommends the use of a seat belt. Depending on the inju- ry, first check with your doctor for specific recommendations.
recommendations. The
Seat belts— —Seat belt precautions Toyota strongly urges that the driver and passengers in the vehicle be properly re- strained at all times with the seat belts provided. Failure to do so could increase the chance of injury and/or the severity of injury in accidents. The seat belts provided for your vehicle are designed for people of adult size, large enough to properly wear them. Child. Use a child restraint system ap- propriate for the child until the child be- comes large enough to properly wear the vehicle’s seat belts. See “Child restraint” on page 67 in this Section for details. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. If a child must sit in the front seat, the seat belts should be worn properly. If an accident occurs and the seat belts are not worn properly, the force of the rapid infla- tion of the airbag may cause death or serious injury to the child.
For your safety and comfort, adjust the head restraint before driving. To raise: Pull it up. To lower: Push it down while pressing the lock release button. The head restraint is most effective when it is close to your head. Therefore, using a cushion on the seatback is not recom- mended.
CAUTION
(cid:1) Adjust the center of the head re- straint so that it is closest to the top of your ears.
(cid:1) After adjusting the head restraint, make sure it is locked in position. the head re-
(cid:1) Do not drive with
straints removed.
40
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
CAUTION
the vehicle
(cid:1) Avoid reclining
in their seats Persons should ride their seat belts properly wearing whenever is moving. Otherwise, they are much more likely to suffer serious bodily injury or death in the event of sudden braking or a collision. When using the seat belts, observe the following: (cid:1) Use the belt for only one person at a time. Do not use a single belt for two or more people—even children. the seatback any more than needed. The seat belts provide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats. If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen or your neck may In the contact the shoulder belt. event of a the more the seat is reclined, the great- er the risk of death or serious inju- ry.
frontal collision,
’08 MATRIX_U (L/O 0706)
(cid:1) Be careful not to damage the belt webbing or hardware. Take care that they do not get caught or pinched in the seat or doors.
(cid:1) Inspect the belt system periodically. Check for cuts, fraying, and loose parts. Damaged parts should be re- placed. Do not disassemble or modify the system.
—Fastening front and rear seat belts
Tab
Buckle
(cid:1) Keep the belts clean and dry.
If
they need cleaning, use a mild soap
solution or lukewarm water. Never
use bleach, dye, or abrasive clean-
ers, or allow them to come
into
the belts—they may
contact with
severely weaken
(See
“Cleaning the interior” on page 257
in Section 5.)
the belts.
(cid:1) Replace the belt assembly (includ- ing bolts) if it has been used in a severe impact. The entire assembly should be replaced even if damage is not obvious.
tab
the
into
insert
Adjust the seat as needed and sit up straight and well back in the seat. To fasten your belt, pull it out of the re- tractor and the buckle. You will hear a click when the tab locks into the buckle. The seat belt length automatically adjusts to your size and the seat position. The retractor will lock the belt during a sudden stop or on impact. It also may lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around freely.
41
2008 COROLLA MATRIX from Aug. ’07 Prod. (OM12B26U)
is
then
When a passenger’s shoulder belt is com- pletely extended and retracted even slightly, the belt is locked in that position and cannot be extended. This fea- ture is used to hold the child restraint system securely. (For details, see “Child restraint” on page 67 in this Section.) To free the belt again, fully retract the belt and then pull the belt out once more. If the seat belt cannot be pulled out of the retractor, firmly pull the belt and release it. You will then be able to smoothly pull the belt out of the retractor.
CAUTION
(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.
(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.
(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed, because it cannot protect an adult occupant or your child from death or serious injury.
42
’08 MATRIX_U (L/O 0706)
Take up slack
Too high
CAUTION
(cid:1) Both high−positioned lap belts and loose−fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on hips as possible.
(cid:1) Do not place the shoulder belt un-
der your arm.
Keeps as low on