2007 Toyota Matrix Owners Manual

battery will explode if a flame or spark is brought near. Use only standardized jumper cables and do not smoke or light a match while jump starting.

NOTICE

The battery used for boosting must be 12 V. Do not jump start unless you are sure that the booster battery is correct.

(c) Jump starting To avoid serious personal injury and damage to your vehicle which might re- sult from battery explosion, acid burns, electrical burns, or damaged electronic components, these instructions must be followed precisely. If you are unsure about how to follow this procedure, we strongly that you seek the help of a competent me- chanic or towing service.

recommend

CAUTION

(cid:1) Batteries

contain

sulfuric

acid which is poisonous and corrosive. Wear protective safety glasses when jump starting, and avoid spilling acid on your skin, clothing, or ve- hicle.

(cid:1) If you should accidentally get acid on yourself or in your eyes, remove any contaminated clothing and flush the affected area with water im- mediately. Then get immediate medi- cal attention. If possible, continue to apply water with a sponge or cloth while en route to the medical office.

JUMP STARTING PROCEDURE 1. If

is

the booster battery

installed in another vehicle, make sure the vehicles are not touching. Turn off all unneces- sary lights and accessories. When boosting, use the battery of matching or higher quality. Any other battery may be difficult to jump start with. If jump starting is difficult, charge the battery for several minutes.

2. If required, remove all the vent plugs from the booster and discharged batter- ies. Lay a cloth over the open vents on the batteries. (This helps reduce the explosion hazard, personal injuries and burns.)

3. If the engine in the vehicle with the booster battery is not running, start it and let it run for a few minutes. During jump starting, run the engine at about 2000 rpm with the accelerator pedal lightly depressed.

223

Positive terminal (“+” mark)

Discharged battery

Jumper cable Positive terminal

(“+” mark)

Discharged battery

Booster battery

4. Make the cable connections in the or-

der a, b, c, d. a. Connect the clamp of the positive (red) jumper cable to the positive (+) terminal on the discharged battery. b. Connect the clamp at the other end of the positive (red) jumper cable to the positive (+) terminal on the booster battery.

Booster battery

Negative terminal (“−” mark)

Jumper cable

c. Connect the clamp of the negative (black) cable to the negative (−) termi- nal on the booster battery. d. Connect the clamp at the other end of the negative (black) jumper cable to a solid, stationary, unpainted, metallic point of the vehicle with the discharged battery. The recommended connecting point is shown in the following illustration:

224

Connecting point

Do not connect the cable to or near any part that moves when the engine is cranked.

CAUTION

the connections,

to When making avoid serious injury, do not lean over the battery or accidentally the jumper cables or clamps touch any- thing except the correct battery termi- nals or the ground.

let

If your engine stalls while driving If your engine stalls while driving... 1. Reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place.

2. Turn on your emergency flashers. 3. Turn

ignition key

the

to try starting

“ACC” or the engine

“LOCK”, and again.

If the engine will not start, see “If your vehicle will not start” on page 222 in this Section.

CAUTION

If the engine is not running, the pow- er assist for the brakes and steering will not work so steering and braking will be much harder than usual.

5. Start your engine in the normal way. After starting, run it at about 2000 rpm for several minutes with the accelerator pedal lightly depressed.

6. Carefully disconnect the cables in the exact reverse order: the negative cable and then the positive cable.

7. Carefully dispose of the battery cover cloths—they may now contain sulfuric acid.

8. If removed, replace all the battery vent

plugs.

If the cause of your battery discharging is not apparent (for example, lights left on), you should have it checked at your Toyota dealer. If the first start attempt is not success- ful... Check jumper cables are tight. Recharge the discharged battery with the jumper cables connected for several minutes and restart your en- gine in the normal way. If the another attempt is not successful, the battery may be depleted. Have it ch- ecked at your Toyota dealer.

the clamp on

that

the

If you cannot increase engine speed If engine speed does not increase when the accelerator pedal is depressed, there may be a problem somewhere in the elec- tronic throttle control system. At this time, vibration may occur. Howev- er, if you depress the accelerator pedal more firmly and slowly, you can drive your vehicle at low speeds. Have your vehicle checked by your Toyota dealer as soon as possible. Even if the abnormality of the electronic throttle control system is corrected during low speed driving, the system may not be recovered until the engine is stopped and the ignition key to “ACC” or “LOCK” position.

turned

is

CAUTION

Be especially careful to prevent erro- neous pedal operation.

225

6. After

the engine coolant

temperature has cooled to normal, again check the coolant level in the reservoir. If neces- sary, bring it up to half full again. Seri- ous coolant loss indicates a leak in the system. You should have it checked as soon as possible at your Toyota dealer.

If your vehicle overheats If your engine coolant temperature gauge indicates overheating, if you ex- perience a loss of power, or if you hear a loud knocking or pinging noise, the engine has probably overheated. You should follow this procedure... 1. Pull safely off the road, stop the ve- turn on your emergency hicle and flashers. Put the transmission in “P” (automatic) or neutral (manual) and ap- ply the parking brake. Turn off the air conditioning if it is being used.

2. If coolant or steam is boiling out of the radiator or reservoir, stop the engine. Wait until the steam subsides before opening the hood. If there is no coolant boiling over or steam, leave the engine running and make sure the electric cooling fan is operating. If it is not, turn the ignition off.

CAUTION

injury, keep To help avoid personal the hood closed until there is no steam. Escaping steam or coolant is a sign of very high pressure.

226

3. Look for obvious coolant leaks from the radiator, hoses, and under the vehicle. However, note that water draining from the air conditioning is normal if it has been used.

CAUTION

the engine

When is running, keep hands and clothing away from the moving fan and engine drive belts.

4. If the coolant is leaking, stop the en- gine immediately. Call a Toyota dealer for assistance.

5. If there are no obvious leaks, check the coolant reservoir. If it is dry, add coolant to the reservoir while the en- gine is running. Fill it about half full. For the coolant type, see “Coolant type selection” on page 270 in Section 7−2.

CAUTION

Do not attempt to remove the radiator cap when the engine and radiator are hot. Serious injury could result from scalding hot fluid and steam blown out under pressure.

If you have a flat tire— 1. Reduce your speed gradually while driving in a straight line. Move cautiously off the road to a safe place well away from the traf- fic. Avoid stopping on the center divider of a highway. Park on a lev- el spot with firm ground.

2. Stop the engine and turn on your

emergency flashers.

3. Firmly set the parking brake and put the transmission in “P” (auto- matic) or reverse (manual).

4. Have everyone get out of the ve- hicle on the side away from traffic. 5. Read the following instructions

thoroughly.

CAUTION

When jacking, be sure to observe the following to reduce the possi- bility of personal injury: (cid:1) Follow jacking instructions. (cid:1) Do not put any part of your body under the vehicle sup- ported by the jack. Otherwise, personal injury may occur.

(cid:1) Do not start or run the engine while your vehicle is supported by the jack.

(cid:1) Stop the vehicle on a level firm ground, firmly set the parking brake and put the transmission in “P” (automatic) or reverse (manual). Block the wheel diag- onally opposite to the one be- ing changed if necessary.

(cid:1) Make sure to set the jack prop- erly in the jack point. Raising the vehicle with jack improper- ly positioned will damage the vehicle or may allow the ve- hicle to fall off the jack and cause personal injury.

(cid:1) Never get under the vehicle when the vehicle is supported by the jack alone.

(cid:1) Use the jack only for lifting your vehicle during wheel changing.

(cid:1) Do not raise the vehicle with

someone in the vehicle.

(cid:1) When raising the vehicle, do not place any objects on top of or underneath the jack.

(cid:1) Raise the vehicle only high enough to remove and change the tire.

227

NOTICE

Do not continue driving with a deflated tire. Driving even a short distance can damage a tire and wheel beyond repair.

228

The compact spare tire can be used many times, if necessary. It has tread life of up to 4800 km (3000 miles) de- pending on road conditions and your driving habits. When tread wear indi- cators appear on the tire, replace the tire. See also the tire information on page 275 in Section 7−2 for details on the tread wear indicators and other ser- vice information.

CAUTION

(cid:1) The compact spare tire was de- signed especially for your Toy- ota. Do not use it on any other vehicle.

(cid:1) Do not use more than one com- pact spare tire at the same time.

(cid:1) The pressure for the compact spare tire must be 420 kPa (4.2
kgf/cm2 or bar, 60 psi).

(cid:1) Do not exceed 80 km/h (50
mph) when driving with the compact spare tire.

the

distinctive

Compact spare tire The compact spare tire is designed for temporary emergency use only. The compact spare tire is identified by wording “TEMPORARY USE ONLY” molded into the side wall of the tire. The compact spare tire saves space in your luggage compartment, and its lighter weight helps to improve fuel economy and permits easier installa- tion in case of a flat tire.

(cid:1) Replace the compact spare tire with the standard tire as soon as possible.

(cid:1) Avoid sudden acceleration, sudden deceleration and sharp turns with the compact spare tire.

NOTICE

Your ground clearance is re- duced when the compact spare tire is installed so avoid driving over obstacles and drive slowly on rough, unpaved roads and speed bumps. Also, do not at- tempt to go through an auto- matic car wash as the vehicle may get caught, resulting in damage.

—Required tools and spare tire

To remove the jack, unhook the tight- ening strap. To store the jack, make sure it is se- curely held by the tightening strap.

1. Open the rear luggage storage box and get the required tools and spare tire. 1. Jack handle 2. Wheel nut wrench 3. Jack 4. Spare tire

To open the rear luggage storage box, see “Luggage storage boxes” on page 173 in Section 1−10. To prepare yourself for an emergency, you should familiarize yourself with the use of the jack, each of the tools and their storage locations.

229

—Blocking the wheel

The compact tire storage area is de- signed only for a compact spare tire. Standard size tires cannot be stored in this storage area.

2. Block the wheel diagonally op- posite the flat tire to keep the vehicle from rolling when it is jacked up.

When blocking the wheel, place a wheel block in front of one of the front wheels or behind one of the rear wheels.

To remove the spare tire: 1. Loosen the nut and remove it. 2. Remove the luggage storage box. 3. Loosen the bolt and remove it. When storing the spare tire, put it in place with the inner side of the wheel facing up. Then secure the tire by re- peating the above removal steps in reverse order to prevent it from flying forward during a collision or sudden braking.

230

—Removing wheel ornament (steel wheels)

—Loosening wheel nuts

CAUTION

Never use oil or grease on the bolts or nuts. The nuts may loose and the wheels may fall off, which could cause a serious ac- cident.

3. Remove the wheel ornament. Pry off the wheel ornament, using the beveled end of the wheel nut wrench as shown.

CAUTION

Do not try to pull off the orna- ment by hand. Take due care in handling the ornament to avoid unexpected personal injury.

4. Loosen all the wheel nuts. Always loosen the wheel nuts before raising the vehicle. Turn the wheel nuts counterclockwise to loosen. To get maximum leverage, fit the wrench to the nut so that the handle is on the right side, as shown above. Grab the wrench near the end of the handle and pull up on the han- dle. Be careful that the wrench does not slip off the nut. Do not remove the nuts yet—just un- screw them about one−half turn.

231

—Positioning the jack

—Raising your vehicle

Jack point guide

5. Position the jack at the correct

jack point as shown.

Make sure the jack is positioned on a level and solid place.

With side mud guards—The jack point guides are located under the side mud guards. They indicate the jack point positions.

6. After making sure that no one is in the vehicle, raise it high enough so that the spare tire can be installed.

Remember you will need more ground clearance when putting on the spare tire than when removing the flat tire. To raise the vehicle, insert the jack handle into the jack (it is a loose fit) and turn it clockwise. As the jack touches the vehicle and begins to lift, double−check that it is properly posi- tioned.

232

—Changing wheels

CAUTION

Never get under the vehicle when the vehicle is supported by the jack alone.

7. Remove the wheel nuts and

change tires.

Lift the flat tire straight off and put it aside. Roll the spare wheel into position and align the holes in the wheel with the bolts. Then lift up the wheel and get at least the top bolt started through its hole. Wiggle the tire and press it back over the other bolts.

Before putting on wheels, remove any corrosion on the mounting surfaces with a wire brush or such. Installation of wheels without good metal−to−met- al contact at the mounting surface can cause wheel nuts to loosen and eventually cause a wheel to come off while driving.

233

—Reinstalling wheel nuts

—Lowering your vehicle

CAUTION

Never use oil or grease on the bolts or nuts. Doing so may lead to overtightening the nuts and damaging the bolts. The nuts may loose and the wheels may fall off, which could cause a seri- ous accident. If there is oil or grease on any bolt or nut, clean it.

8. Reinstall all the wheel nuts fin-

ger tight.

Reinstall the wheel nuts (tapered end inward) and tighten them as much as you can by hand. Press back on the tire back and see if you can tighten them more.

234

9. Lower the vehicle completely

and tighten the wheel nuts.

Turn the jack handle counterclock- wise to lower the vehicle. Use only the wheel nut wrench and turn it clockwise to tighten the nuts. Do not use other tools or any addition- al leverage other than your hands, such as a hammer, pipe or your foot. Make sure the wrench is securely en- gaged over the nut. Tighten each nut a little at a time in the order shown. Repeat the process until all the nuts are tight.

CAUTION

(cid:1) When

lowering the vehicle, make sure all portions of your body and all other persons around will not be injured as the vehicle is lowered to the ground.

(cid:1) Have the wheel nuts tightened with torque wrench to 103 N·m (10.5 kgf·m, 77 ft·lbf), as soon as possible after changing wheels. Otherwise, the nuts may loosen and the wheels may fall off, which could cause a serious accident.

—Stowing flat tire 10.Restow all the tools and jack se- curely in the luggage storage box. Then secure the flat tire in the luggage compartment with the tire tie−down belts and tie− down hooks as follows.

CAUTION

Before driving, make sure all the tools, jack and flat tire are se- curely in place in their storage location to reduce the possibility of personal injury during a colli- sion or sudden braking.

1. Aluminum wheels—Before stow- ing the flat tire, remove the center wheel ornament by pushing from the reverse side.

Be careful not to lose the wheel orna- ment.

235

Buckle

2. Put the flat tire on the rear luggage storage box lid with the outer side of the wheel facing up. Hook the belt clips closest to the buckle to the rear upper tie−down hooks.

3. Pass the belts through the center hole of the wheel as shown above.

4. Attach the other clips of the belts to the lower rear tie−down hooks.

236

5. Position the tire edge against the rear center end of the rear luggage storage box lid. Then pull the ends of the belts to secure the tire se- curely.

After stowing the flat tire, check that the tire and belts are secured. To loosen the tire tie−down belts, see “Tie−down hooks and tire tie−down belts” on page 174 in Section 1−10.

—After changing wheels 11. Check the air pressure of the re-

placed tire.

Adjust the air pressure to the specifi- cation designated on page 300 in Section 8. If the pressure is lower, drive slowly to the nearest service station and fill to the correct pressure. Do not forget to reinstall the tire infla- tion valve cap as dirt and moisture could get into the valve core and possibly cause air leakage. If the cap is missing, have a new one put on as soon as possible. As soon after changing wheels as possible, tighten the wheel nuts to the torque specified on page 300 in Sec- tion 8 with a torque wrench. Have a technician repair the flat tire.

237

After repairing the flat tire, change it with compact spare tire and rein- stall the wheel ornament as fol- lows. Steel wheels— 1. Put the wheel ornament into posi-

tion. Align the cutout of the wheel orna- ment with the valve stem as shown.

2. Press hand firmly on one side of wheel ornament and then firmly tap the other side around the edge of wheel ornament with the heel of your hand to snap into place.

Aluminum wheels— Push the wheel ornament into the center hole.

CAUTION

(cid:1) Take due care in handling the ornament to avoid unexpected personal injury.

(cid:1) Do not attach a heavily dam- aged plastic wheel ornament. It may fly off the wheel and cause accidents while the ve- hicle is moving.

Initial adjustment of the tire pres- sure warning system is necessary after you have replaced your tires or wheels. See “Tire pressure warning system” on page 126 in Section 1−7.

Steel wheels

Aluminum wheels

238

If your vehicle becomes stuck If your vehicle becomes stuck in snow, mud, sand, etc., then you may attempt to rock the vehicle free by moving it forward and backward. Vehicles with traction control system— Turn off the traction control system to become unstuck to allow the tires to spin enough to remove the vehicle from the obstruction. (For details, see “Trac- tion control system” on page 122 in Section 1−7.)

CAUTION

Do not attempt to rock the vehicle free by moving it forward and back- ward if people or objects are any- where near the vehicle. During the rocking operation the vehicle may suddenly move forward or backward as it becomes unstuck, causing injury or damage to nearby people or ob- jects.

If your vehicle needs to be towed—

NOTICE

(a) Towing with wheel lift type truck—

If you rock your vehicle, observe the following precautions to prevent dam- age to the transmission and other parts. (cid:1) Do not depress the accelerator ped- al while shifting the selector lever or before the transmission is com- pletely shifted to forward or reverse gear.

(cid:1) Do not race the engine and avoid

spinning the wheels.

(cid:1) If your vehicle remains stuck after rocking the vehicle several times, consider other ways such as tow- ing.

—From front

—From rear

(b) Using flat bed truck

239

If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. In consultation with them, have your vehicle towed using either (a) or (b). Only when you cannot receive a towing service from a Toyota dealer or com- mercial tow truck service, tow your ve- hicle carefully in accordance with the instructions given in “—Emergency tow- ing” on page 241 in this Section. Proper equipment will help ensure that your vehicle is not damaged while being towed. Commercial operators are generally aware of local laws pertaining to towing. Your vehicle can be damaged is towed incorrectly. Although most operators know the correct procedure, it is possible to make a mistake. To avoid damage to your vehicle, make sure the following pre- cautions are observed. If necessary, show this page to the tow truck driver.

the state/provincial and

if

it

TOWING PRECAUTIONS: Use a safety chain system for all towing, and abide by the state/provincial and local laws. The wheels and axle on the ground must be in good condition. If they are damaged, use a towing dolly. (a) Towing with wheel lift type truck From front—Release the parking brake.

NOTICE

When lifting wheels, take care to en- sure adequate ground clearance for towing at the opposite end of the raised vehicle. Otherwise, the bumper and/or underbody of the towed vehicle will be damaged during towing.

From rear— (cid:1) Manual transmission:

We recommend using a towing dolly under the front wheels. If you do not use a towing dolly, place the ignition key in the “ACC” position and put the transmission in neutral.

NOTICE

Do not tow with the key removed or in the “LOCK” position when towing from the rear without a towing dolly. The steering lock mechanism is not strong enough to hold the front wheels straight.

(cid:1) Automatic transmission:

Use a wheels.

towing dolly under

the

front

NOTICE

Never tow a vehicle with an automatic transmission from the rear with the front wheels on the ground, as this may cause serious damage to the transmission.

(b) Using flat bed truck

240

(c) Towing with sling

type truck

—Emergency towing

(c) Towing with sling type truck

NOTICE

Do not tow with sling type truck, ei- ther from the front or rear. This may cause body damage.

If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. If towing service is not available in an emergency, your vehicle may be tempo- rarily towed by a cable or chain se- cured to the emergency towing eyelet under the front of the vehicle. Use ex- treme caution when towing vehicle.

NOTICE

Only use specified towing eyelet; otherwise your vehicle may be dam- aged.

A driver must be in the vehicle to steer it and operate the brakes. Towing in this manner may be done only on hard−surfaced roads for a short dis- tance and at the wheels, axles, drive train, steering and brakes must all be in good condition.

low speeds. Also,

CAUTION

Use extreme caution when towing ve- hicles. Avoid sudden starts or erratic driving maneuvers which would place excessive stress on the emergency towing eyelet and towing cable or chain. The eyelet and towing cable or chain may break and cause serious injury or damage.

NOTICE

Use only a cable or chain specifically intended for use in towing vehicles. Securely fasten the cable or chain to the towing eyelet provided.

241

If you cannot shift automatic transmission selector lever

Before towing, release the parking brake and put the transmission in neutral (manu- al) or “N” (automatic). The key must be in “ACC” (engine off) or “ON” (engine run- ning).

CAUTION

If the engine is not running, the pow- er assist for the brakes and steering will not work so steering and braking will be much harder than usual.

though

If you cannot shift the selector lever out of “P” position to other positions even is de- pressed, use the shift lock override but- ton as follows: 1. Turn

the brake pedal

ignition key

the

to “LOCK” the parking

position. Make sure brake is applied.

2. Pry up the cover with a flathead

screwdriver or equivalent.

242

3. Insert your finger into the hole to push down the shift lock override button. You can shift out of “P” position only while pushing the but- ton.

4. Shift into “N” position. 5. Insert the cover. 6. Start the engine. For your safety,

keep the brake pedal depressed.

Be sure to have the system checked by your Toyota dealer as soon as possible.

If you lose your keys You can purchase a new key at your Toyota dealer if you can give them the key number. Even if you lose only one key, contact your Toyota dealer to make a new key. If you lose all your master keys, you cannot make new keys; the whole engine immobi- lizer system must be replaced. See page 10 in Section 1−2. If your keys are locked in the vehicle and you cannot get a duplicate, many Toyota dealers can still open the door for you, If you must using break a window in, we suggest breaking the smallest side window be- cause it is the least expensive to replace. Be extremely cautious to avoid cuts from the glass.

the suggestion given in “Keys” on

their special

to get

tools.

If you lose your wireless remote control transmitter You can purchase a new wireless re- mote control transmitter at your Toyota dealer. Have the registered identification numbers of your transmitters deleted from your ve- hicle by your Toyota dealer as soon as possible to avoid the possibility of theft or an accident. Then, have the identification number of your new transmitter registered. At the same time, you must bring all of the remaining transmitters to have them registered again as well. You can use the wireless remote control system with the new transmitter. Contact your Toyota dealer for detailed information.

243

244

SECTION 5

CORROSION PREVENTION AND APPEARANCE CARE Corrosion prevention and appearance care Protecting your Toyota from corrosion Washing and waxing your Toyota Cleaning the interior

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

246
247
249

245

Protecting your Toyota from corrosion Toyota, through the diligent research, de- sign and use of the most advanced technology available, helps prevent corro- sion and provides you with the finest qual- ity vehicle construction. Now, it is up to you. Proper care of your Toyota can help ensure long−term corrosion prevention. The most common causes of corrosion to your vehicle are: (cid:1) The accumulation of road salt, dirt and moisture in hard−to−reach areas under the vehicle.

(cid:1) Chipping of paint, or undercoating caused by minor accidents or by stones and gravel.

Care is especially important if you live in particular areas or operate your ve- hicle under certain environmental condi- tions: (cid:1) Road salt or dust control chemicals will accelerate corrosion, as will the pres- ence of salt in the air near the sea− coast or in areas of industrial pollution. (cid:1) High humidity accelerates corrosion es- pecially when temperatures range just above the freezing point.

246

(cid:1) Wetness or dampness to certain parts of your vehicle for an extended period of time, may cause corrosion even though other parts of the vehicle may be dry.

(cid:1) High ambient temperatures can cause corrosion to those components of the vehicle which do not dry quickly due to lack of proper ventilation.

The above signifies the necessity to keep your vehicle, particularly the underside, as clean as possible and to repair any dam- age to paint or protective coatings as soon as possible. To help prevent corrosion on your Toyota, follow these guidelines: Wash your vehicle frequently. It is, of course, necessary to keep your vehicle clean by regular washing, but to prevent corrosion, the following points should be observed: (cid:1) If you drive on salted roads

the winter or if you live near the ocean, you should hose off the undercarriage at least once a month to minimize cor- rosion.

in

(cid:1) High pressure water or steam is effec- tive for cleaning the vehicle’s underside and wheel housings. Pay particular attention to these areas as it is difficult to see all the mud and dirt. It will do more harm than good to simply wet the mud and debris without removing. The lower edge of doors, rocker panels and frame members have drain holes which should not be allowed to clog with dirt as trapped water in these areas can cause corrosion.

(cid:1) Wash the underside of the vehicle thor-

oughly when winter is over.

See “Washing and waxing your Toyota” on page 247 for more tips. Check the condition of your vehicle’s paint and trim. If you find any chips or scratches in the paint, touch them up im- mediately to prevent corrosion from start- ing. If the chips or scratches have gone through the bare metal, have a qualified body shop make the repair.

Washing and waxing your Toyota Washing your Toyota Keep your vehicle clean by regular washing. The following cases may cause weakness to the paint or corrosion to the body and parts. Wash your vehicle as soon as pos- sible. (cid:1) When driving in a coastal area (cid:1) When driving on a road sprinkled with

antifreeze

(cid:1) When exposed to coal tar, tree sap, bird droppings and carcass of an insect (cid:1) When driving in areas where there is a lot of smoke, soot, dust, iron dust or chemical substances

(cid:1) When the vehicle becomes remarkably

dirty with dust and mud

Check the interior of your vehicle. Wa- ter and dirt can accumulate under the floor mats and could cause corrosion. Oc- casionally check under the mats to make sure the area is dry. Be particularly care- ful when transporting chemicals, cleans- ers, fertilizers, salt, etc.; these should be transported in proper containers. If a spill or leak should occur, immediately clean and dry the area. Use mud shields on your wheels. If you drive on salted or gravel roads, mud shields help protect your vehicle. Full−size shields, which come as near to the ground as possible, are the best. We recommend that the fittings and the area where the shields are installed be treated to resist corrosion. Your Toyota dealer will be happy to assist in supplying and installing the shields if they are recommended for your area. Keep your vehicle in a well ventilated garage or a roofed place. Do not park your vehicle in a damp, poorly venti- lated garage. If you wash your vehicle in the garage, or if you drive it covered with water or snow, your garage may be so damp as to cause corrosion. Even if your garage is heated, a wet vehicle can cor- rode if the ventilation is poor.

Hand−washing your Toyota Work in the shade and wait until the vehicle body is not warm to the touch.

CAUTION

(cid:1) When cleaning under floor or chas- sis, be careful not to injure your hands.

(cid:1) Exhaust gases cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot ex- haust pipe can cause burns.

1. Rinse off loose dirt with a hose. Re- move any mud or road salt from the underside of the vehicle or the wheel wells.

2. Wash with a mild car−wash soap, mixed according to the manufacturer’s instructions. Use a soft cotton mitt and keep it wet by dipping it frequently into the wash water. Do not rub hard—let the soap and water remove the dirt.

247

Fuel filler door: Do not apply water (high− pressure car wash, for example) at or near the fuel tank inlet with the fuel filler door opened. If the water enters the air vent, you may experience trouble with re- fueling or rough engine idling. Plastic wheel ornaments: The plastic wheel ornaments are damaged easily by organic substances. If any organic sub- stances splash an ornament, be sure to wash them off with water and check if the ornament is damaged. Aluminum wheels: Use only a mild soap or neutral detergent. Plastic bumpers: Wash carefully. Do not scrub with abrasive cleaners. The bumper faces are soft.

248

tar: Remove with

Exterior lights: Wash carefully. Do not use organic substances or scrub them with a hard brush. This may damage the sur- faces of the lights. Road turpentine or cleaners that are marked safe for painted surfaces. 3. Rinse

can cause streaking. In hot weather you may need to rinse each section right after you wash it.

thoroughly—dried

soap

4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not rub or press hard—you might scratch the paint.

NOTICE

(cid:1) Do not use organic substances (gasoline, kerosene, benzine or strong solvents), which may be tox- ic or cause damage.

(cid:1) Do not scrub any part of the ve- hicle with a hard brush, which may cause damage.

Automatic car wash Your vehicle may be washed in an auto- matic car wash, but remember that the paint can be scratched by some types of brushes, unfiltered washing water, or the washing process itself. Scratching reduces paint durability and gloss, especially on darker colors. The manager of the car wash should be able to advise you wheth- er the process is safe for the paint on your vehicle.

NOTICE

To prevent damage to the antenna, make sure it is removed before driv- ing your Toyota through an automatic car wash.

Waxing your Toyota Polishing and waxing is recommended to maintain the original beauty of your Toyota’s finish. Apply wax once a month or if the vehicle surface does not repel water well. 1. Always wash and dry the vehicle be- fore you begin waxing, even if you are using a combined cleaner and wax.

2. Use a good quality polish and wax. If the finish has become extremely weath- ered, use a car−cleaning polish, fol- lowed by a separate wax. Carefully fol- low the manufacturer’s instructions and precautions. Be sure to polish and wax the chrome trim as well as the paint. Exterior lights: Do not apply wax on the surfaces of the lights. Wax may cause damage to the lenses. If you accidentally put wax on the light surfaces, wipe or wash it off. 3. Wax

the vehicle again when water does not bead but remains on the sur- face in large patches.

Cleaning the interior

CAUTION

(cid:1) Vehicles with side airbags and cur-

tain shield airbags: Be careful not to splash water or spill liquid on the floor. This may prevent the side airbags from acti- vating correctly, resulting in serious injury.

(cid:1) Do not wash the vehicle floor with water, or allow water to get onto the floor when cleaning the vehicle interior or exterior. Water may get into audio components or other electrical components above or un- der the floor carpet (or mat) and cause a malfunction; and it may cause body corrosion.

Vinyl interior The vinyl upholstery may be easily cleaned with a mild soap or detergent and water. First vacuum over the upholstery to re- move loose dirt. Then, using a sponge or soft cloth, apply the soap solution to the vinyl. After allowing it to soak in for a few minutes to loosen the dirt, remove the dirt and wipe off the soap with a clean damp cloth. If all the dirt do not come off, re- peat the procedure. Commercial foaming− type vinyl cleaners are also available which work well. Follow the manufacturer’s instructions.

NOTICE

Do not use solvent, thinner, gasoline or window cleaner on the interior.

249

to

foam−type shampoo

Carpets Use a good clean the carpets. Begin by vacuuming thoroughly to remove as much dirt as possible. Several types of foam cleaners are available; some are in aerosol cans and others are powders or liquids which you mix with water to pro- duce a foam. To shampoo the carpets, use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water—the best results are obtained by keeping the carpet as dry as possible. Read the shampoo instructions and follow them closely. Seat belts The seat belts may be cleaned with mild soap and water or with lukewarm water. Use a cloth or sponge. As you are clean- ing, check the belts for excessive wear, fraying, or cuts.

NOTICE

(cid:1) Do not use dye or bleach on the

belts—it may weaken them.

(cid:1) Do not use the belts until they be-

come dry.

250

(cid:1) If you use a liquid car freshener, do not apply the liquid onto the ve- hicle’s interior surfaces. It may con- tain the ingredients mentioned above. Immediately clean any spill using the method mentioned above.

Leather interior The leather upholstery may be cleaned with neutral detergent for wool. Remove dirt using a soft cloth dampened with 5% solution of neutral detergent for wool. Then thoroughly wipe off all traces of detergent with a clean damp cloth. After cleaning or whenever any part of the leather gets wet, dry with a soft clean cloth. Allow the leather to dry in a venti- lated shaded area.

Windows The windows may be cleaned with any household window cleaner.

NOTICE

When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.

Air conditioning control panel, audio panel, instrument panel, console panel, and switches Use a soft damp cloth for cleaning. Soak a clean soft cloth in water or luke- warm water then lightly wipe off dirt.

NOTICE

(cid:1) Do not use organic substances (sol- vents, kerosene, alcohol, gasoline, etc.) or alkaline or acidic solutions. These chemicals can cause discol- oring, staining or peeling of the surface.

(cid:1) If you use cleaners or polishing agents, make sure their ingredients do not include the substances men- tioned above.

(cid:1) The interior of your vehicle is apt to heat up on hot summer days, so avoid placing on the upholstery items made of vinyl or plastic or containing wax as these tend to stick to leather when warm.

(cid:1) Improper cleaning of the leather up- holstery could result in discolor- ation or staining.

If you have any questions about the cleaning of your Toyota, your local Toyota dealer will be pleased to answer them.

NOTICE

(cid:1) If a stain should fail to come out with a neutral detergent, apply a cleaner that does not contain an organic solvent.

(cid:1) Never use organic substances such as benzine, alcohol or gasoline, or alkaline or acid solutions for clean- ing the leather as these could cause discoloring.

(cid:1) Use of a nylon brush or synthetic fiber cloth, etc. may scratch the fine grained surface of the leather. (cid:1) Mildew may develop on soiled leath- er upholstery. Be especially careful to avoid oil spots. Try to keep your upholstery always clean.

(cid:1) Long exposure to direct sunlight may cause the leather surface to harden and shrink. Keep your ve- hicle in a shaded area, especially in the summer.

251

252

SECTION 6

VEHICLE MAINTENANCE AND CARE Vehicle maintenance and care Maintenance requirements General maintenance Does your vehicle need repairing? Emissions Inspection and Maintenance (I/M) programs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

254
255
257
258

For scheduled maintenance the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

information, please refer

to

253

Maintenance requirements Your Toyota vehicle has been designed for fewer maintenance requirements with long- er service intervals to save both your time and money. However, each regular mainte- nance, as well as day−to−day care, is more important than ever before to ensure smooth, and trouble−free, safe, and eco- nomical drivings. It is the owner’s responsibility to make sure the specified maintenance, including general maintenance service, is performed. Note that both the new vehicle and emis- sion control system warranties specify that proper maintenance and care must be per- formed. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for complete warranty information. General maintenance General maintenance items are those day− to−day care practices that are important to your vehicle for proper operation. It is the owner’s responsibility to ensure that the general maintenance items are performed regularly. These checks or inspections can be done either by yourself or a qualified technician, or if you prefer, your Toyota dealer will be pleased to do them at a nominal cost.

254

Scheduled maintenance The scheduled maintenance items listed in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement” are those required to be serviced at regular inter- vals. For details of your maintenance schedule, read the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any replacement parts used for maintenance or for the repair of the emission control system be Toyota supplied. The owner may elect to use non−Toyota supplied parts replacement pur- poses without invalidating the emission control system warranty. However, use of replacement parts which are not of equivalent quality may impair the effec- tiveness of the emission control sys- tems. You may also elect to have mainte- nance, replacement, or repair of the emission control devices and system performed by any automotive repair es- tablishment or individual without invali- dating this warranty. See “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement” for complete war- ranty information.

for

Where to go for service? Toyota technicians are well−trained spe- cialists and are kept up to date with the latest service information through technical bulletins, service tips, and in−dealership training programs. They learn to work on Toyotas before they work on your vehicle, rather than while they are working on it. You can be confident that your Toyota dealer’s service department performs the best job to meet the maintenance require- ments on your vehicle—reliably and eco- nomically. Your copy of the repair order is proof that all required maintenance has been per- formed for warranty coverage. If any prob- lems should arise with your vehicle while under warranty, your Toyota dealer will promptly take care of it. Again, be sure to keep a copy of the repair order for any service performed on your Toyota. What about do−it−yourself maintenance? Many of the maintenance items are easy to do yourself if you have a little mechani- cal ability and a few basic automotive tools. Simple instructions for how to per- form them are presented on page 259 in Section 7.

If you are a skilled do−it−yourself mechan- ic, the Toyota service manuals are recom- mended. Please be aware that do−it−your- self maintenance can affect your warranty coverage. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for the details.

the

items

listed,

General maintenance Listed below are the general maintenance items that should be performed as fre- quently as specified. In addition to check- ing if you notice any unusual noise, smell or vibration, you should investigate the cause or take your vehicle to your Toyota dealer or a quali- fied service shop immediately. It is recom- mended that any problem you notice be brought to the attention of your dealer or the qualified service shop for their advice.

CAUTION

Make these checks only with ade- quate ventilation if you run the en- gine.

IN THE ENGINE COMPARTMENT Items listed below should be checked from time to time, e.g. each time when refueling. Washer fluid Make sure there is sufficient fluid in the tank. See page 285 in Section 7−3 for additional information.

Engine coolant level Make sure the coolant level is between the “FULL” and “LOW” lines on the see− through reservoir when the engine is cold. See page 270 in Section 7−2 for addition- al information. Radiator, condenser and hoses Check that the front of the radiator and condenser are clean and not blocked with leaves, dirt, or insects. See page 271 in Section 7−2 for additional information. Battery condition Check the battery condition by the indica- tor color. See page 282 in Section 7−3 for additional information. Brake fluid level Make sure the brake fluid level is correct. See page 271 in Section 7−2 for addition- al information. Engine oil level Check the level on the dipstick with the engine turned off and the vehicle parked on a level spot. See page 268 in Section 7−2 for additional information.

255

Power steering fluid level Check the level through the reservoir. The level should be in the “HOT” or “COLD” range depending on the fluid temperature. See page 272 in Section 7−2 for addition- al information. Exhaust system If you notice any change in the sound of the exhaust or smell exhaust fumes, have the cause located and corrected immedi- ately. (See “Engine exhaust cautions” on page 184 in Section 2.) INSIDE THE VEHICLE Items listed below should be checked regularly, e.g. while performing periodic services, cleaning the vehicle, etc. Lights Make sure the headlights, stop lights, tail lights, turn signal lights, and other lights are all working. Service reminder indicators and warning buzzers Check that all service reminder indicators and warning buzzers function properly. Steering wheel Check that it has the specified free play. Be alert for changes in steering condition, such as hard steering or strange noise. 256

the

that

Seats Check that all front seat controls such as seat adjusters, seatback recliner, etc. op- erate smoothly and that all latches lock securely in any position. Check that the head restraints move up and down smoothly and that the locks hold securely in any latched position. For folding−down rear seatbacks, check latches lock securely. Seat belts Check that the seat belt system such as buckles, retractors and anchors operate properly and smoothly. Make sure the belt webbing is not cut, frayed, worn or dam- aged. Accelerator pedal Check the pedal for smooth operation and uneven pedal effort or catching. Clutch pedal Check the pedal for smooth operation. Brake pedal Check the pedal for smooth operation and that the pedal has the proper clearance. Check the brake booster function. Brakes In a safe place, check that the brakes do not pull to one side when applied.

Parking brake Check that the lever has the proper travel and that, on a safe incline, your vehicle is held securely with only the parking brake applied. Automatic transmission “Park” mecha- nism Check the lock release button of the se- lector lever for proper and smooth opera- tion. On a safe incline, check that your vehicle is held securely with the selector lever in “P” position and all brakes re- leased. OUTSIDE THE VEHICLE Items listed below should be performed from time, unless otherwise specified. Fluid leaks Check underneath for leaking fuel, oil, wa- ter or other the vehicle has been parked for a while. If you smell fuel fumes or notice any leak, have the cause found and corrected immediately.

fluid after

time

to

latch secures

Doors and engine hood Check that all doors and back door includ- ing glass hatch operate smoothly and all latches lock securely. Make sure the en- gine hood secondary the hood from opening when the primary latch is released. Tire inflation pressure Check the pressure with a gauge ev- ery two weeks, or at least once a month. See page 272 in Section 7−2
for additional information. Tire surface and wheel nuts Check the tires carefully for cuts, damage or excessive wear. See page 275 in Section 7−2 for additional in- formation. When checking the tires, make sure no nuts are missing, and check the nuts for looseness. Tighten them if necessary. Tire rotation Rotate the tires according to the maintenance schedule. (For sched- uled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supple- ment”.) See page 277 in Section 7−2
for additional information.

tip−offs

for changes

Does your vehicle need repairing? Be on the alert in perfor- mance, sounds, and visual that indicate service is needed. Some impor- tant clues are as follows: (cid:1) Engine missing, stumbling, or pinging (cid:1) Appreciable loss of power (cid:1) Strange engine noises (cid:1) A leak under the vehicle (however, wa- ter dripping from the air conditioning after use is normal.)

(cid:1) Change

in exhaust sound (This may indicate a dangerous carbon monoxide leak. Drive with the windows open and have the exhaust system checked im- mediately.)

(cid:1) Flat−looking tire; excessive tire squeal

when cornering; uneven tire wear

(cid:1) Vehicle pulls to one side when driving

straight on a level road

(cid:1) Strange noises related to suspension

movement

(cid:1) Loss of brake effectiveness; spongy feeling brake or clutch pedal; pedal al- most touches floor; vehicle pulls to one side when braking

(cid:1) Engine coolant temperature continually

higher than normal

If you notice any of these clues, take your vehicle to your Toyota dealer as soon as possible. It probably needs adjustment or repair.

CAUTION

Do not continue driving with the ve- hicle unchecked. It could result in se- rious vehicle damage and possibly personal injury.

257

The malfunction indicator lamp will go off after taking several driving trips, but the error code in the OBD system will not be cleared unless about 40 trips or more are taken. If your vehicle does not pass the I/M test even the malfunction indicator lamp does not come on, contact your Toyota dealer to prepare the vehicle for re−testing.

indicator

the malfunction

in- include OBD

Emissions Inspection and Maintenance (I/M) programs Some states have vehicle emission spection programs which (On−Board Diagnostics) checks. The OBD system monitors the operation of the emission control system. When the OBD system determines that a problem exists somewhere in the emission control system, lamp comes on. In this case, your vehicle may the I/M test and need to be not pass repaired. Contact your Toyota dealer to service the vehicle. Even lamp does not come on, your vehicle may not pass readiness codes have not been set in the OBD system. Readiness codes are automatically set during ordinary driving. However, when the battery is disconnected or run down, the codes are erased. Also, depending on your driving habits, the codes may not be completely set. Also, if the malfunction indicator lamp had come on recently due to temporary mal- function such as a loose fuel tank cap, your vehicle may not pass the I/M test.

the malfunction

indicator

test as

I/M

the

if

258

SECTION 7− 1

DO−IT−YOURSELF MAINTENANCE Introduction Engine compartment overview Fuse locations Do−it−yourself service precautions Parts and tools Positioning the jack

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

260
261
261
263
264

259

1. Power steering fluid reservoir 2. Engine oil level dipstick 3. Engine coolant reservoir 4. Engine oil filler cap 5. Brake fluid reservoir 6. Fuse block 7. Battery 8. Radiator 9. Electric cooling fan 10. Condenser 11. Windshield and rear window washer

fluid tank

Engine compartment overview

260

Fuse locations

Spare fuses

Do−it−yourself service precautions If you perform maintenance by yourself, be sure to follow the correct procedure given in this Section. You should be aware that improper or in- complete servicing may result in operating problems. Performing do−it−yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement for details and suggestions. This Section gives for those items that are relatively easy for an owner to perform. As explained in Section 6, there are still a number of items that must be done by a qualified technician with special tools. For information on tools and parts for do− it−yourself maintenance, see “Parts and tools” on page 263 in this Section. Utmost care should be taken when work- ing on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to ob- serve:

instructions only

261

CAUTION

(cid:1) When the engine is running, keep hands, clothing, and tools away from the moving fan and engine drive rings, watches, and ties is advisable.)

(Removing

belts.

(cid:1) Right after driving,

the engine compartment—the engine, radiator, exhaust manifold, power steering fluid reservoir and spark plug boots, etc.—will be hot. So be care- ful not to touch them. Oil, fluids and spark plugs may also be hot.

(cid:1) If the engine is hot, do not remove the radiator cap or loosen the drain plugs to prevent burning yourself.

(cid:1) Do not

leave anything

that may burn easily, such as paper or rags, in the engine compartment.

(cid:1) Do not smoke, cause sparks or al- low open flames around fuel or the battery. Their fumes are flammable. (cid:1) Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.

262

(cid:1) Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on, the electric cooling fans will automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.

(cid:1) Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc. (cid:1) Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your skin, wash thoroughly with soap and water.

(cid:1) Do not

leave used oil within the

reach of children.

(cid:1) Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your dealer or a service station information concerning recycling or disposal.

for

(cid:1) Be extremely cautious when work- ing on the battery. It contains poi- sonous and corrosive sulfuric acid.

NOTICE

(cid:1) Remember that battery and ignition cable carry high currents or volt- ages. Be careful of accidentally causing a short circuit.

(cid:1) Add only “Toyota Super Long Life Coolant” or similar high quality eth- ylene glycol based non−silicate, non−amine, non−nitrite, and non−bo- rate coolant with long−life hybrid organic acid technology to fill the radiator. “Toyota Super Long Life Coolant” is a mixture of 50% cool- ant and 50% deionized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).

(cid:1) If you spill some of the coolant, be sure to wash it off with water to prevent it from damaging the parts or paint.

(cid:1) Do not allow dirt or anything else to fall through the spark plug holes. (cid:1) Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.

(cid:1) Do not reuse iridium−tipped spark

plugs by cleaning or regapping.

(cid:1) Do not overfill automatic transmis- sion fluid, or the transmission could be damaged.

(cid:1) Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.

(cid:1) Be careful not to scratch the glass

surface with the wiper frame.

(cid:1) When closing the engine hood, check to see that you have not for- gotten any tools, rags, etc.

Parts and tools Here is a list of parts and tools you will need to perform do−it−yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. CHECKING THE ENGINE OIL LEVEL Parts (if level is low): (cid:1) “Toyota Genuine Motor Oil” or equiva-

lent See Section 7−2 for details about en- gine oil selection.

Tools: (cid:1) Rag or paper towel (cid:1) Funnel (only for adding oil) CHECKING THE ENGINE COOLANT LEVEL Parts (if level is low): (cid:1) “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−ni- trite, and non−borate coolant with long− life hybrid organic acid technology. “Toyota Super Long Life Coolant” is a mixture of 50% coolant and 50% deion- ized water (for the U.S.A.) or 55% coolant and 45% deionized water (for Canada).

Tools: (cid:1) Funnel (only for adding coolant) CHECKING BRAKE FLUID Parts (if level is low): (cid:1) SAE J1703 or FMVSS No.116 DOT 3

brake fluid

Tools: (cid:1) Rag or paper towel (cid:1) Funnel (only for adding fluid) CHECKING POWER STEERING FLUID Parts (if level is low): (cid:1) Automatic

transmission

fluid

DEXRON(cid:2)II or III

Tools: (cid:1) Rag or paper towel (cid:1) Funnel (only for adding fluid) CHECKING BATTERY CONDITION Tools: (cid:1) Warm water (cid:1) Baking soda (cid:1) Grease (cid:1) Conventional wrench

(for

terminal

clamp bolts)

263

Positioning the jack

CHECKING AND REPLACING FUSES Parts (if replacement is necessary): (cid:1) Fuse with same amperage rating as

original

ADDING WASHER FLUID Parts: (cid:1) Water (cid:1) Washer fluid containing antifreeze

(for winter use)

Tools: (cid:1) Funnel REPLACING LIGHT BULBS Parts: (cid:1) Bulb with same number and wattage rating as original in “Replacing light bulbs” on page 286 in Section 7−3.)

charts

(See

Tools: (cid:1) Screwdriver

264

Front

Rear

When jacking up your vehicle with the jack, position jack correctly as shown in the illustrations.

the