2012 Toyota Corolla Owners Manual

Automatic transmission

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

(→P. 147) (→P. 139)

With the shift lever in D, depress the brake pedal. Set the parking brake. Shift the shift lever to P. When parking on a hill, if necessary, block the wheels. Vehicles with smart key system: Turn the “ENGINE START STOP” switch OFF and stop the engine. Vehicles without smart key system: Turn the engine switch to the “LOCK” position and stop the engine. Lock the door, making sure that you have the key on your person.

Manual transmission

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

With the clutch pedal fully depressed, depress the brake pedal. (→P. 147) Set the parking brake. Shift the shift lever to N. (→P. 145) When parking on a hill, shift the shift lever to 1 or R. If necessary, block the wheels. Turn the engine switch to the “LOCK” position and stop the engine. Lock the door, making sure that you have the key on your person.

121

2-1. Driving procedures

Starting on a steep uphill

Automatic transmission

STEP 1

STEP 2

STEP 3

Firmly set the parking brake and shift the shift lever to D. Gently depress the accelerator pedal. Release the parking brake.

Manual transmission

STEP 1

STEP 2

STEP 3

With the parking brake firmly set and the clutch pedal fully depressed, shift the shift lever to 1. Lightly depress the accelerator pedal at the same time as gradually releasing the clutch pedal. Release the parking brake.

■Driving in the rain

●Drive carefully when it is raining, because visibility will be reduced, the

windows may become fogged-up, and the road will be slippery.

●Drive carefully when it starts to rain, because the road surface will be

especially slippery.

●Refrain from high speeds when driving on an expressway in the rain, because there may be a layer of water between the tires and the road surface, preventing the steering and brakes from operating properly.

■Engine speed while driving

In the following conditions, the engine speed may become high while driving. This is due to automatic up-shifting control or down-shifting implementation to meet driving conditions. It does not indicate sudden acceleration. ●The vehicle is judged to be driving uphill or downhill ●When the accelerator pedal is released

122

2

2-1. Driving procedures

■Breaking in your new Toyota

To extend the life of the vehicle, the following precautions are recommended to observe: ●For the first 200 miles (300 km):

Avoid sudden stops.

●For the first 500 miles (800 km):

Do not tow a trailer.

●For the first 1000 miles (1600 km):

• Do not drive at extremely high speeds. • Avoid sudden acceleration. • Do not drive slowly with the manual transmission in a high gear. • Do not drive at a constant speed for extended periods.

■Drum-in-disc type parking brake system (2.4 L 4-cylinder [2AZ-FE]

engine) Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down.

■Operating your vehicle in a foreign country

Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (→P. 468)

123

2-1. Driving procedures

CAUTION

■When starting the vehicle (vehicles with an automatic transmission)

Always keep your foot on the brake pedal while stopped with the engine run- ning. This prevents the vehicle from creeping.

■When driving the vehicle

●Do not drive if you are unfamiliar with the location of the brake and accel-

erator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake pedal will result in sudden acceleration that may lead to an accident that could result in death or serious injury.

• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly, allowing you to depress the brake and accelerator pedals properly.

• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.

●Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. This may cause a fire if there is any flammable material nearby.

●Vehicles with an automatic transmission: Do not let the vehicle roll back- wards while the shift lever is in a driving position, or roll forward while the shift lever is in R. Doing so may cause the engine to stall or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle.

●If the smell of exhaust is noticed inside the vehicle, open the windows and check that the trunk is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immedi- ately.

124

2

2-1. Driving procedures

CAUTION

●On vehicles with an automatic transmission, do not shift the shift lever to P

while the vehicle is moving. Doing so can damage the transmission and may result in a loss of vehicle control.

●Do not shift the shift lever to R while the vehicle is moving forward.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Do not shift the shift lever to D (vehicles with an automatic transmission) or 1 (vehicles with a manual transmission) while the vehicle is moving back- ward. Doing so can damage the transmission and may result in a loss of vehicle control.

●Moving the shift lever to N while the vehicle is moving will disengage the engine from the transmission. Engine braking is not available when N is selected.

●During normal driving, do not turn off the engine. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so. However, in the event of an emergency, such as if it becomes impossible to stop the vehicle in the normal way: →P. 461

●Use engine braking (downshift) to maintain a safe speed when driving down a steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (→P. 141)

●When stopped on an inclined surface, use the brake pedal and parking brake to prevent the vehicle from rolling backward or forward and causing an accident.

●Do not adjust the position of the steering wheel, the seat, or the inside or outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents that may result in death or serious injury.

●Always check that all passengers' arms, heads or other parts of their bod- ies are not outside the vehicle, as this may result in death or serious injury.

125

2-1. Driving procedures

CAUTION

●Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires. Driving over 85 mph (140 km/h) may result in tire failure, loss of control and possible injury. Be sure to consult a tire dealer to determine whether the tires on your vehicle are high-speed capability tires or not before driving at such speeds. ■When driving on slippery road surfaces

●Sudden braking, acceleration and steering may cause tire slippage and

reduce your ability to control the vehicle, resulting in an accident.

●Sudden changes in engine speed, such as engine braking caused by up- shifting or down-shifting, may cause the vehicle to skid, resulting in an accident.

●After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.

■When shifting the shift lever (vehicles with an automatic transmission)

Be careful not to shift the shift lever with the accelerator pedal depressed. This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

■When the vehicle is stopped

●Do not race the engine. If the vehicle is in any gear other than P (vehicles with an automatic transmission) or N, the vehicle may accelerate suddenly and unexpectedly, and may cause an accident.

●Do not leave the vehicle with the engine running for a long time.

If such a situation cannot be avoided, park the vehicle in an open space and check that exhaust fumes do not enter the vehicle interior.

●Vehicles with an automatic transmission: In order to prevent accidents due to the vehicle rolling away, always keep depressing the brake pedal while the engine is running, and apply the parking brake as necessary.

●If the vehicle is stopped on an incline, in order to prevent accidents caused by the vehicle rolling forward or backward, always depress the brake pedal and securely apply the parking brake as needed.

126

2

2-1. Driving procedures

CAUTION

●Avoid revving or racing the engine.

Running the engine at high speed while the vehicle is stopped may cause the exhaust system to overheat, which could result in a fire if combustible material is nearby.

■When the vehicle is parked

●Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in

the vehicle when it is in the sun. Doing so may result in the following. • Gas may leak from a cigarette lighter or spray can, and may lead to a

fire.

• The temperature inside the vehicle may cause the plastic lenses and

plastic material of eye glasses to deform or crack.

• Soft drink cans may fracture, causing the contents to spray over the interior of the vehicle, and may also cause a short circuit in the vehi- cle's electrical components.

●Always apply the parking brake, shift the shift lever to P (automatic trans-

mission vehicles), stop the engine and lock the vehicle. Do not leave the vehicle unattended while the engine is running.

●Do not touch the exhaust pipe while the engine is running or immediately

after turning the engine off. Doing so may cause burns.

●Do not leave the engine running in an area with snow build-up, or where it is snowing. If snowbanks build up around the vehicle while the engine is running, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

■Exhaust gases

Exhaust gases include harmful carbon monoxide (CO) that is colorless and odorless. Inhaling exhaust gases may lead to death or a serious health haz- ard. ●If the vehicle is in a poorly ventilated area, stop the engine. In a closed area, such as a garage, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

127

2-1. Driving procedures

CAUTION

●The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard. ■When taking a nap in the vehicle

Always turn the engine off. Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.

■When braking the vehicle

●When the brakes are wet, drive more cautiously. Braking distance increases when the brakes are wet, and may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle.

●If the power brake assist function does not operate, do not follow other

vehicles closely and avoid downhills or sharp turns that require braking. In this case, braking is still possible, but it will require more force on the pedal than usual. Braking distance may also increase.

●Do not pump the brake pedal if the engine stalls.

Each push on the brake pedal uses up the reserve for the power-assisted brakes.

●The brake system consists of 2 individual hydraulic systems: If one of the systems fails, the other will still operate. In this case, the brake pedal should be depressed more firmly than usual and braking distance becomes longer. Do not drive your vehicle with only a single brake system. Have your brakes fixed immediately.

128

2-1. Driving procedures

NOTICE

■When driving the vehicle

●Do not depress the accelerator and brake pedals at the same time during driving. If the brake pedal is depressed while driving with the accelerator pedal depressed, driving torque may be restrained. Manual transmission

●Do not shift gears unless the clutch pedal is fully depressed. After shifting, do not release the clutch abruptly. Doing so may damage the clutch, tran- saxle and gears.

●Do not rest your foot on the clutch pedal while driving.

Doing so may cause clutch trouble.

●Do not use any gears other than the first gear when starting off and mov-

ing forward. Doing so may damage the clutch.

●Do not use the clutch to hold the vehicle when stopping on an uphill grade.

Doing so may damage the clutch.

●Do not shift into reverse when the vehicle is still moving. Doing so may

damage the clutch, transaxle and gears. Automatic transmission

●Do not use the accelerator pedal or depress the accelerator and brake

pedals together to hold the vehicle on a hill.

■When parking the vehicle (vehicles with an automatic transmission)

Always put the shift lever in P. Failure to do so may cause the vehicle to move or the vehicle may accelerate suddenly if the accelerator pedal is acci- dentally depressed.

■Avoiding damage to vehicle parts

●Do not turn the steering wheel fully in either direction and hold it there for

an extended period of time. Doing so may damage the power steering motor.

●When driving over bumps in the road, drive as slowly as possible to avoid

damaging the wheels, underside of the vehicle, etc.

129

2-1. Driving procedures

NOTICE

■If you hear a squealing or scraping noise (brake pad wear limit indica-

tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage can result if the pads are not replaced when needed. It is dangerous to drive the vehicle when the wear limits of the brake pads and/or those of the brake discs are exceeded.

■If you get a flat tire while driving

A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually press the brake pedal to slow down the vehicle. ●It may be difficult to control your vehicle. ●The vehicle will make abnormal sounds. ●The vehicle will behave abnormally. Replace a flat tire with a new one. (→P. 435)

■When encountering flooded roads

Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle. ●Engine stalling ●Short in electrical components ●Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. ●Brake function ●Changes in quantity and quality of engine oil, and transaxle fluid etc. ●Lubricant condition for the bearings and suspension joints (where possi-

ble) and the function of all joints, bearings, etc.

130

2-1. Driving procedures Engine (ignition) switch (vehicles with smart key system)

Performing the following operations when carrying the electronic key on your person starts the engine or changes “ENGINE START STOP” switch modes. ■ Starting the engine

STEP 1

STEP 2

STEP 3

Check that the parking brake is set. Check that the shift lever is set in P. Sit in the driver’s seat and firmly depress the brake pedal. The “ENGINE START STOP” switch indicator turns green. If the indicator does not turn green, the engine cannot be started.

STEP 4

Press the “ENGINE START STOP” switch.

The engine will crank until it starts or for up to 25 seconds, whichever is less. If you press and hold the “ENGINE START STOP” switch, the engine will keep cranking for about 30
seconds maximum. Continue depressing the brake pedal until the engine is com- pletely started. The engine can be started from any “ENGINE START STOP” switch mode.

131

2-1. Driving procedures

■ Changing “ENGINE START STOP” switch mode

Modes can be changed by pressing the “ENGINE START STOP” switch with the brake pedal released. (The mode changes each time the switch is pressed.)

OFF* The emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can be used. The “ENGINE START STOP” switch indicator turns amber. IGNITION ON mode All electrical components can be used. The “ENGINE START STOP” switch indicator turns amber.

*: If the shift lever is in a position other than P when turning off the engine, “ENGINE START STOP” switch will be turned to ACCESSORY mode, not to OFF.

the

132

■Steering lock release

2-1. Driving procedures

Make sure that the steering wheel lock is released. To release the steering wheel lock, gently turn the wheel left or right while pressing the “ENGINE START STOP” switch. If the steering wheel lock does not release, the “ENGINE START STOP” switch indicator will flash green.

■If the engine does not start

The engine immobilizer system may not have been deactivated. (→P. 81) ■When the “ENGINE START STOP” switch indicator flashes in amber

The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately. ■Auto power OFF function

If the vehicle is left in ACCESSORY mode for more than an hour with the shift lever in P, the “ENGINE START STOP” switch will automatically turn OFF.

■Key battery depletion

→P. 31

■When the electronic key battery is discharged

→P. 385

■Conditions affecting operation

→P. 29

■Note for the entry function

→P. 31

133

2-1. Driving procedures

CAUTION

■When starting the engine

Always start the engine while sitting in the driver's seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

■Stopping the engine in an emergency

If you want to stop the engine in an emergency while driving the vehicle, push and hold the “ENGINE START STOP” switch for more than 3 seconds. However, do not touch the “ENGINE START STOP” switch while driving except in an emergency. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so.

NOTICE

■To prevent battery discharge

Do not leave the “ENGINE START STOP” switch in ACCESSORY or IGNI- TION ON mode for long periods without the engine running.

■When starting the engine ●Do not race a cold engine. ●If the engine becomes difficult to start or stalls frequently, have the engine

checked immediately.

134

2

2-1. Driving procedures Engine (ignition) switch (vehicles without smart key system)

■ Starting the engine

Automatic transmission

STEP 1

STEP 2

STEP 3

STEP 4

Check that the parking brake is set. Check that the shift lever is set in P. Sit in the driver’s seat and firmly depress the brake pedal. Turn the engine switch to the “START” position and start the engine. 1.8 L 4-cylinder (2ZR-FE) engine: The engine will crank until it starts or for up to 25 seconds, whichever is less. If you turn the engine switch, the engine will keep cranking for about 30 seconds maximum. Continue depressing the brake pedal until the engine is com- pletely started.

Manual transmission

STEP 1

STEP 2

STEP 3

STEP 4

Check that the parking brake is set. Check that the shift lever is set in N. Firmly depress the clutch pedal. Turn the engine switch to the “START” position and start the engine. 1.8 L 4-cylinder (2ZR-FE) engine: The engine will crank until it starts or for up to 25 seconds, whichever is less. If you turn the engine switch, the engine will keep cranking for about 30 seconds maximum. Continue depressing the brake pedal until the engine is com- pletely started.

135

2-1. Driving procedures

■ Changing engine switch position

“LOCK” The steering wheel is locked and the key can be removed. (Vehicles with an automatic transmission: The key can be removed only when the shift lever is in P.) “ACC” Some electrical components such as the audio system can be used. “ON” All electrical components can be used. “START” For starting the engine.

■Turning the engine switch from “ACC” to “LOCK”

STEP 1

STEP 2

Shift the shift lever to P (auto- matic transmission) or N (man- ual transmission). (→P. 139, 145) Push in the key and turn to the “LOCK” position.

136

2

■Steering lock release

2-1. Driving procedures

When starting the engine, the engine switch may seem stuck in the “LOCK” position. To free it, turn the key while turn- ing the steering wheel slightly in either direction.

■If the engine does not start

The engine immobilizer system may not have been deactivated. (→P. 81)

■Key reminder buzzer

A buzzer sounds if the driver’s door is opened while the engine switch is in the “LOCK” position to remind you to remove the key.

CAUTION

■When starting the engine

Always start the engine while sitting in the driver's seat. Do not depress the accelerator while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

■Caution when driving

Do not turn the engine switch to the “LOCK” position while driving. If, in an emergency, you must turn the engine off while the vehicle is moving, turn the engine switch only to the “ACC” position.

137

2-1. Driving procedures

NOTICE

■To prevent battery discharge

Do not leave the key in the “ACC” or “ON” position for long periods if the engine is not running.

■When starting the engine

●2.4 L 4-cylinder (2AZ-FE) engine: Do not crank for more than 30 seconds

at a time. This may overheat the starter and wiring systems.

●Do not race a cold engine. ●If the engine becomes difficult to start or stalls frequently, have the engine

checked immediately.

138

2-1. Driving procedures Automatic transmission∗

Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever

Standard type

Vehicles with smart key system: While the “ENGINE START STOP” switch is in IGNITION ON mode, depress the brake pedal and move the shift lever. Vehicles without smart key system: While the engine switch is in the “ON” position, depress the brake pedal and move the shift lever.

∗: If equipped 139

2-1. Driving procedures

Multi-mode type

While the engine switch is in the “ON” position, depress the brake pedal and move the shift lever.

140

■ Shift position uses

Shift position

2-1. Driving procedures

Function

Standard type Multi-mode type Parking the vehicle or starting the engine

Reversing Neutral

Normal driving*1

S mode driving*2

(→P. 142)

Position for engine

braking

Position for more

powerful engine braking Position for maximum

engine braking

*1: Shifting to the D position allows the system to select a gear suitable for driving conditions. Setting the shift lever to the D position is recom- mended for normal driving.

*2: Selecting shift ranges using S mode restricts the upper limit of the possible gear ranges, controls engine braking forces, and prevents unnecessary upshifting.

141

2-1. Driving procedures

Changing shift ranges in S mode (multi-mode type)

Shift the shift lever to the S position and operate the shift lever.

Upshifting Downshifting

The initial shift range in S mode is set automatically to 5 or 4. How- ever, the initial shift range may be set to 3 if AI-SHIFT has operated while the shift lever was in the D position. (→P. 144) When the shift range is 4 or lower, holding the shift lever toward “+” sets the shift range to 5.

142

2

2-1. Driving procedures

■ Shift ranges and their functions

Shift range

Function

A gear between 1 and 5 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 4 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 3 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 2 is automatically selected according to vehicle speed and driving conditions. Setting the gear at 1.

A lower shift range will provide greater engine braking forces than a higher shift range.

■Downshifting restrictions (standard type)

The shift lever cannot be downshifted if the following speeds are exceeded. mph (km/h)

Downshifting

Maximum speed

3→2
2→L

59 (95) 28 (46)

■Downshift restriction warning buzzer (multi-mode type ⎯ S mode)

To help ensure safety and driving performance, downshifting operation may sometimes be restricted. In some circumstances, downshifting may not be possible even when the shift lever is operated. (The warning buzzer will sound twice.)

143

2-1. Driving procedures

■When driving with cruise control activated (if equipped)

Standard type

Even when performing the following actions with the intent of enabling engine braking, engine braking will not activate while downshifting to 3
because cruise control will not be canceled. (→P. 169)

Multi-mode type

Even when performing the following actions with the intent of enabling engine braking, engine braking will not activate while driving in S mode and downshifting to 4 because cruise control will not be canceled. (→P. 169)

■If the shift lever cannot be shifted from P

→P. 446

■If the “S” indicator does not come on even after shifting the shift lever

to S (multi-mode type) This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the vehicle will operate as if the shift lever is in D.)

■AI-SHIFT

AI-SHIFT automatically selects the suitable gear according to driver perfor- mance and driving conditions.

Standard type

AI-SHIFT automatically operates when the shift lever is in the D position.

Multi-mode type

AI-SHIFT automatically operates when the shift lever is in the D position. (Shifting the shift lever to the S position cancels the function.)

144

2-1. Driving procedures Manual transmission∗

■ Shifting the shift lever

Fully depress the clutch pedal before operating the shift lever, and then release the clutch pedal slowly.

■Maximum allowable speeds

Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary.

2.4 L 4-cylinder (2AZ-FE) engine

mph (km/h)

Shift position

Maximum speed

29 (48) 53 (85) 81 (130) 110 (178)

1.8 L 4-cylinder (2ZR-FE) engine

Shift position

Maximum speed

mph (km/h)

33 (54) 56 (90) 81 (130)

∗: If equipped 145

2-1. Driving procedures Turn signal lever

Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change. The left hand signal will flash until you release the lever.

■Turn signals can be operated when

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

Vehicles without smart key system

The engine switch is in the “ON” position. ■If the indicators flash faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

146

2

2-1. Driving procedures Parking brake

U.S.A. Canada

Sets the parking brake Fully set the parking brake while depressing the brake pedal. Releases the parking brake Slightly raise the lever and lower it completely while pressing the but- ton.

■Usage in winter time

See “Winter driving tips” for parking brake usage in winter time. (→P. 181)

NOTICE

■Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

147

2-1. Driving procedures Horn

To sound the horn, press on or close to the

mark.

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P. 66)

148

2

2-2. Instrument cluster Gauges and meters

Type A

Type B

149

2-2. Instrument cluster

Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Low fuel level warning light →P. 422
Odometer/trip meter/instrument panel light control and trip meter reset button Switches between odometer and trip meter displays. Pressing and holding the button will reset the trip meter when the trip meter is being displayed. To adjust the brightness of the instrument panel light, turn the button. (→P. 151) Odometer and trip meter display Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently. Multi-information display →P. 156
Display button Switches the multi-information display. Engine coolant temperature gauge Displays the engine coolant temperature.

150

2-2. Instrument cluster

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Darker Brighter

NOTICE

■To prevent damage to the engine and its components

●Do not let the indicator needle of the tachometer enter the red zone, which

indicates the maximum engine speed.

●The engine may be overheating if the engine coolant temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 456)

151

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. ■ Instrument cluster

Type A

Type B

152

■ Center panel

2-2. Instrument cluster

153

2-2. Instrument cluster

■ Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

Front fog light indicator (→P. 164)

Cruise control indicator (→P. 169)

Cruise control set indi- cator (→P. 169)

(if equipped)

(if equipped)

(if equipped)

*1

“PASSENGER AIR BAG ON” and “PASSENGER AIR BAG OFF” indicator (→P. 98)

Turn signal indicator (→P. 146)

Headlight high beam indicator (→P. 161)

*1, 2

Slip indicator (→P. 173)

Engine immobilizer sys- tem indicator (→P. 81)

VSC OFF indicator (→P. 174)

“TRAC OFF” indicator (→P. 174)

*1

*1

Shift position indicators (→P. 139) (vehicles with an automatic transmission)

*1: These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with smart key system) or the engine switch is turned to the “ON” position (vehicles without smart key system) to indicate that a system check is being per- formed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.

*2: The light flashes to indicate that the system is operating.

154

2-2. Instrument cluster

■ Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 420)

*1

*1

(Canada) *1

(U.S.A.) *1

*1

*1

*1

*1

*1

*1

*1

*1

(Canada) *1

(U.S.A.) *2

(Canada)

(U.S.A.)

(U.S.A.)

(U.S.A.)

(if equipped)

(Canada)

(on the

instrument

cluster)

(if equipped)

(on the center panel)

*1: These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with smart key system) or the engine switch is turned to the “ON” position (vehicles without smart key system) to indicate that a system check is being per- formed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.

*2: The light flashes to indicate a malfunction.

CAUTION

■If a safety system warning light does not come on

Should a safety system light such as the ABS or SRS airbag warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

155

2-2. Instrument cluster Multi-information display

The multi-information display presents the driver with a variety of driving-related data, including the outside temperature.

● Outside

temperature dis-

play Indicates the outside tempera- ture.

● Trip information

Displays driving range, fuel consumption and other cruis- ing-related information.

Display items can be switched by pressing the display button.

Switch the display

● Outside temperature

Displays the outside air temperature.

The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C).

● Instantaneous fuel consumption

Displays the instantaneous of fuel consumption.

156

2-2. Instrument cluster

● Average fuel consumption

Displays the average fuel consumption since the function was reset.

• The function can be reset by pressing the display button for longer than one second when the aver- age fuel consumption is displayed.

• Use the displayed average fuel consumption as a

reference.

● Driving range

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining.

• This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed. • When only a small amount of fuel is added to the

tank, the display may not be updated. Vehicles without smart key system

When refueling, turn the engine off. If the vehicle is refueled without turning the engine off, the dis- play may not be updated.

Vehicles with smart key system

When refueling, turn the “ENGINE START STOP” switch OFF. If the vehicle is refueled without turn- ing the “ENGINE START STOP” switch OFF, the display may not be updated.

157

2-2. Instrument cluster

● Average vehicle speed

● Elapsed time

Displays the average vehicle speed since the engine was started or since the function was reset.

The function can be reset by pressing the display but- ton for longer than one second when the average vehicle speed is displayed.

Displays the elapsed time since the engine was started or since the function was reset.

The function can be reset by pressing the display but- ton for longer than one second when the elapsed time is displayed.

■When disconnecting and reconnecting battery terminals

The following information data will be reset. ●Average fuel consumption ●Driving range ●Average vehicle speed ●Elapsed time

■Display

In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change. ●When stopped, or driving at low speeds (less than 12 mph [20 km/h]) ●When the outside temperature has changed suddenly (at the entrance/

exit of a garage, tunnel, etc.)

158

2-2. Instrument cluster

NOTICE

■The multi-information display at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.

159

run-

lights

The daytime ning lights turn on. The side marker, parking, tail, license plate, daytime run- and ning instrument panel lights turn on. The headlights and all lights listed above (except daytime run- ning lights) turn on.

2-3. Operating the lights and wipers Headlight switch

Type A

160

2

2-3. Operating the lights and wipers

Type B

run-

lights

The daytime ning lights turn on. The side marker, parking, tail, license plate, daytime run- ning and instrument panel lights turn on. The headlights and all lights listed above (except daytime run- ning lights) turn on.

Turning on the high beam headlights

With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release the lever to turn them off. You can flash the high beams with the headlights on or off.

161

2-3. Operating the lights and wipers

■Daytime running light system

●To make your vehicle more visible to other drivers, the headlights turn on automatically whenever the engine is started and the parking brake is released.

●Compared to turning on the headlights, the daytime running light system offers greater durability and consumes less electricity, so it can help improve fuel economy.

●Vehicles with daytime running light control sensor: The brightness of headlights will automatically change depending on the darkness of the surroundings. The other exterior lights and instrument panel lights auto- matically turn on or off.

■Daytime running light control sensor (if equipped)

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the daytime running light sys- tem to malfunction.

interferes with

■Light reminder buzzer

Vehicles without smart key system

A buzzer sounds when the engine switch is turned OFF and the driver's door is opened with the key removed from the engine switch while the lights are turned on.

Vehicles with smart key system

A buzzer sounds when the “ENGINE START STOP” switch is turned OFF or to ACCESSORY mode and the driver's door is opened while the lights are turned on.

162

2-3. Operating the lights and wipers

NOTICE

■To prevent battery discharge

Do not leave the lights on longer than necessary when the engine is not run- ning.

163

2-3. Operating the lights and wipers Fog light switch∗

The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam.

Type A

Off Front fog lights on

164

∗: If equipped

Type B

2-3. Operating the lights and wipers

Off Front fog lights on

165

2-3. Operating the lights and wipers Windshield wipers and washer

Wiper intervals can be adjusted for intermittent operation.

Type A

Intermittent wind- shield wiper opera- tion Low speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation

the

Increases intermittent windshield wiper frequency* Decreases the intermittent windshield wiper frequency* *: The interval adjuster may not be equipped depending on the grade.

166

2-3. Operating the lights and wipers

Wash/wipe operation

Wipers operate automatically.

Type B

Intermittent wind- shield wiper opera- tion Low speed wind- shield wiper opera- tion High speed wind- shield wiper opera- tion Temporary operation

the

Increases intermittent windshield wiper frequency* Decreases the intermittent windshield wiper frequency* *: The interval adjuster may not be equipped depending on the grade.

167

2-3. Operating the lights and wipers

Wash/wipe operation

Wipers operate automatically.

■The windshield wipers and washers can be operated when

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

Vehicles without smart key system

The engine switch is in the “ON” position.

■If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

■When the windshield is dry

Do not use the wipers, as they may damage the windshield.

■When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.

■When a nozzle becomes blocked

In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged.

168

2-4. Using other driving systems Cruise control∗

Use the cruise control to maintain a set speed without depressing the accelerator pedal.

Indicators Cruise control switch

■ Setting the vehicle speed

STEP 1

Press the “ON-OFF” button to activate the cruise control.

indicator will

Cruise control come on. Press deactivate the cruise control.

the button again

to

STEP 2

Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set the speed.

“SET” indicator will come on. The vehicle speed at the moment the lever is released becomes the set speed.

∗: If equipped 169

2-4. Using other driving systems

■ Adjusting the set speed To change the set speed, operate the lever until the desired set speed is obtained.

Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold lever in the desired direction.

the

The set speed will be increased or decreased as follows: Fine adjustment: By approximately 1 mph (1.6 km/h) each time the lever is operated. Large adjustment: The set speed can be increased or decreased con- tinually until the lever is released.

170

2

2-4. Using other driving systems

■ Canceling and resuming the constant speed control

Pulling the lever toward you cancels the constant speed control. The speed setting is also can- celed when the brakes are applied or the clutch pedal (manual transmission only) is depressed. Pushing resumes speed control. Resuming is available when the vehicle speed is more than approximately 25 mph (40 km/h).

lever up constant

the the

■Cruise control can be set when

●Automatic transmission:

The shift lever is in the D or range 3 (standard type), or in the D or range 4 or higher of S has been selected (multi-mode type).

●Vehicle speed is above approximately 25 mph (40 km/h).

■Accelerating after setting the vehicle speed

●The vehicle can be accelerated normally. After acceleration, the set

speed resumes.

●Even without canceling the cruise control, the set speed can be increased by first accelerating the vehicle to the desired speed and then pushing the lever down to set the new speed.

171

2-4. Using other driving systems

■Automatic cruise control cancelation

Cruise control will stop maintaining the vehicle speed in any of the following situations. ●Actual vehicle speed falls more than approximately 10 mph (16 km/h)

below the preset vehicle speed. At this time, the memorized set speed is not retained.

●Actual vehicle speed is below approximately 25 mph (40 km/h). ●VSC is activated.

■If the cruise control indicator light flashes

Press the “ON-OFF” button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.

CAUTION

■To avoid operating the cruise control by mistake

Switch the cruise control off using the “ON-OFF” button when not in use.

■Situations unsuitable for cruise control

Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills

Vehicle speed may exceed the set speed when driving down a steep hill.

●When your vehicle is towing a trailer or during emergency towing

172

2

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■ ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

■ Brake assist

Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation.

■ VSC (Vehicle Stability Control)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

■ TRAC (Traction Control)

Maintains drive power and prevents the front wheels from spinning when starting the vehicle or accelerating on slippery roads.

■ EPS (Electric Power Steering)

Employs an electric motor to reduce the amount of effort needed to turn the steering wheel.

When VSC and TRAC are operating

If the vehicle is in danger of slip- ping or the front wheels spin, the indicator flashes to indicate that VSC/TRAC have been engaged.

173

2-4. Using other driving systems

To disable TRAC and/or VSC

If the vehicle gets stuck in fresh snow or mud, TRAC and VSC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. ■ Turning off TRAC

■ Turning off TRAC and VSC

Quickly push and release the switch to turn off TRAC.

The “TRAC OFF” indicator light should come on. Push the switch again to turn the system back on.

Push and hold the switch while the vehicle is stopped to turn off TRAC and VSC.

indicator

The “TRAC OFF” indicator light and VSC OFF light should come on. Push the switch again to turn the system back on.

■Automatic reactivation of TRAC and VSC

Turning the “ENGINE START STOP” switch or the engine switch OFF after turning off the TRAC and VSC systems will automatically re-enable them.

■Automatic TRAC reactivation

If only the TRAC system is turned off, the TRAC system will turn on when vehicle speed increases.

■Automatic TRAC and VSC reactivation

If the TRAC and VSC systems are turned off, the systems will not turn on even when vehicle speed increases.

174

2

2-4. Using other driving systems

■When the “TRAC OFF” indicator light comes on even if the VSC OFF

switch has not been pressed TRAC cannot be operated. Contact your Toyota dealer.

■Sounds and vibrations caused by ABS, brake assist, VSC and TRAC ●A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in any of these systems.

●Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after ABS is activated. • The brake pedal may move down slightly after ABS is activated.

■If the slip indicator light comes on

There is a malfunction in the TRAC and VSC systems. Contact your Toyota dealer and have your Toyota inspected.

■EPS operation sound

When the steering wheel is operated, a motor sound (whirring sound) may be heard. This does not indicate a malfunction.

■Reduced effectiveness of the EPS system

The effectiveness of the EPS system is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the engine off. The EPS system should return to normal within 10 minutes.

CAUTION

■ABS does not operate effectively when

●Tires with inadequate gripping ability are used (such as excessively worn

tires on a snow covered road).

●The vehicle hydroplanes while driving at high speed on the wet or slick

road.

175

2-4. Using other driving systems

CAUTION

■Stopping distance when the ABS is operating may exceed that of nor-