2009 Toyota Corolla Owners Manual

l Trip information

Displays driving range, fuel consumption and other cruis- ing-related information.

Display items can be switched by pressing the display button.

Displays the clock.

l Clock

146

2-2. Instrument cluster

l Outside temperature

Displays the outside air temperature.

The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C).

Instantaneous fuel consumption

Displays the instantaneous of fuel consumption.

l Average fuel consumption

l Driving range

Displays the average fuel consumption since the function was reset.

The function can be reset by pressing the display but- ton for longer than one second when the average fuel consumption is displayed.

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining.

• This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed. • When only a small amount of fuel is added to the

tank, the display may not be updated.

147

2-2. Instrument cluster

l Average vehicle speed

Displays the average vehicle speed since the engine was started or since the function was reset.

The function can be reset by pressing the display but- ton for longer than one second when the average vehicle speed is displayed.

Displays the elapsed time since the engine was started or since the function was reset.

The function can be reset by pressing the display but- ton for longer than one second when the elapsed time is displayed.

l Elapsed time

Setting the clock

STEP 1

Display the clock when the vehicle is stopped. (→P. 146)

STEP 2

Press and hold the display but- ton to enter the adjustment mode for the clock.

STEP 3

STEP 4

Press the display button to adjust the minutes. After adjusting the minutes, wait 5 seconds to allow the minutes to be automatically input. Press the display button to adjust the hours. After adjusting the hours, wait 5 seconds to allow the hours to be automatically input.

148

2

2-2. Instrument cluster

n When disconnecting and reconnecting battery terminals

The following information data will be reset. l Clock l Average fuel consumption l Driving range l Average vehicle speed l Elapsed time

NOTICE

n The multi-information display at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.

149

2-3. Operating the lights and wipers Headlight switch

U.S.A.* Canada*

side marker, The parking, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on.

*: Vehicles with optitron type

meters

Turning on the high beam headlights

With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release the lever to turn them off. You can flash the high beams with the headlights on or off.

150

2-3. Operating the lights and wipers

n Daytime running light system

To make your vehicle more visible to other drivers, the headlights turn on automatically whenever the engine is started and the parking brake is released. The brightness of headlights will automatically change depending on the darkness of the surroundings. The other exterior lights and instrument panel lights automatically turn on or off.

n Daytime running light control sensor

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the daytime running light sys- tem to malfunction.

interferes with

n Light reminder buzzer

Vehicles without smart key system

A buzzer sounds when the engine switch is turned OFF and the driver's door is opened with the key removed from the engine switch while the lights are turned on.

Vehicles with smart key system

A buzzer sounds when the “ENGINE START STOP” switch is turned OFF or to ACCESSORY mode and the driver's door is opened while the lights are turned on.

NOTICE

n To prevent battery discharge

Do not leave the lights on longer than necessary when the engine is not run- ning.

151

2-3. Operating the lights and wipers Fog light switch (if equipped)

The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam.

Off Front fog lights on

152

2-3. Operating the lights and wipers Windshield wipers and washer

Wiper can be operated manually.

windshield

Intermittent wiper operation Low speed windshield wiper operation High wiper operation Temporary operation

speed windshield

Wash/wipe operation

Wipers operate automatically.

153

2-3. Operating the lights and wipers

n The windshield wipers and washers can be operated when

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

Vehicles without smart key system

The engine switch is in the “ON” position.

n Intermittent windshield wiper interval mode (if equipped)

Wiper intervals can be adjusted for intermittent operation.

Decreases the intermittent windshield wiper frequency Increases the intermittent windshield wiper frequency

n If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

n When the windshield is dry

Do not use the wipers, as they may damage the windshield.

n When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.

n When a nozzle becomes blocked

Do not try to clear it with a pin or other object. The nozzle will be damaged.

154

2-4. Using other driving systems Cruise control (if equipped)

Use cruise control to maintain a set speed without using the acceler- ator. n Setting the vehicle speed STEP 1

Press the “ON-OFF” button to activate the cruise control.

Press the button once more to deactivate the cruise control.

STEP 2

Accelerate or decelerate to the desired speed and push the lever down to set the cruise control speed.

n Adjusting the speed setting

Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pushing the lever up or down and releasing it.

155

2-4. Using other driving systems

n Canceling and resuming regular acceleration

Cancel Pull the lever towards you to cancel cruise control. The speed setting is also can- celed when the brakes are applied or the clutch pedal (manual is depressed. Resume To resume cruise control and return to the set speed, push the lever up.

transmission)

n Cruise control can be set when

l Automatic transmission:

The shift lever is in D or 3 (standard type), or in D, 4 or 5 range of S (multi-mode type).

l Vehicle speed is above 25 mph (40 km/h).

n Accelerating

The vehicle can be accelerated normally.

156

2

2-4. Using other driving systems

n Automatic cruise control cancellation

The set speed is automatically canceled in any of the following situations. l Actual vehicle speed falls more than 10 mph (16 km/h) below the preset

vehicle speed. At this time, the memorized set speed is not retained.

l Actual vehicle speed is below 25 mph (40 km/h). l VSC is activated.

n If the cruise control indicator light flashes

Press the “ON-OFF” button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Contact your Toyota dealer and have your Toyota inspected.

CAUTION

n To avoid operating the cruise control by mistake

Keep the “ON-OFF” button off when not in use.

n Situations unsuitable for cruise control

In heavy traffic

Do not use cruise control in any of the following situations. Doing so may result in control of the vehicle being lost and could cause seri- ous or fatal accident. l On roads with sharp bends l On winding roads l On slippery roads, such as those covered with rain, ice or snow l On steep hills

157

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. n ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

n Brake assist

Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation.

n VSC (Vehicle Stability Control) (if equipped)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

n TRAC (Traction Control) (if equipped)

Maintains drive power and prevents the front wheels from spinning when starting the vehicle or accelerating on slippery roads.

n EPS (Electric Power Steering)

Employs an electric motor to reduce the amount of effort needed to turn the steering wheel.

When VSC and TRAC are operating

If the vehicle is in danger of slip- ping or the front wheels spin, the indicator flashes to indicate that VSC/TRAC have been engaged. A buzzer (intermittent) sounds to indicate that VSC is operating.

158

2-4. Using other driving systems

To disable TRAC and/or VSC

If the vehicle gets stuck in fresh snow or mud, TRAC and VSC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. n Turning off TRAC

Quickly push and release the button to turn off TRAC.

n Turning off TRAC and VSC

The slip indicator light should come on. Push the button again to turn the system back on.

Push and hold the button while the vehicle is stopped to turn off TRAC and VSC.

The slip indicator light and “VSC OFF” indicator light should come on. Push the button again to turn the system back on.

n Automatic reactivation of TRAC and VSC

Turning the “ENGINE START STOP” switch or the engine switch OFF after turning off the TRAC and VSC systems will automatically re-enable them.

n Automatic TRAC reactivation

If only the TRAC system is turned off, the TRAC system will turn on when vehicle speed increases.

n Automatic TRAC and VSC reactivation

If the TRAC and VSC systems are turned off, the systems will not turn on even when vehicle speed increases.

159

2-4. Using other driving systems

n Sounds and vibrations caused by ABS, brake assist, VSC and TRAC l A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in any of these systems.

l Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after ABS is activated. • The brake pedal may move down slightly after ABS is activated.

n If the “VSC OFF” indicator light flashes

There is a malfunction in the TRAC and VSC systems. Contact your Toyota dealer and have your Toyota inspected.

n EPS operation sound

When the steering wheel operates, a motor sound (whirring sound) may be heard. This does not indicate a malfunction.

n Reduced effectiveness of EPS

The effectiveness of EPS is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the engine off. The sys- tem should return to normal within 10 minutes.

CAUTION

n ABS does not operate effectively when

l Tires with inadequate gripping ability are used (such as excessively worn

tires on a snow covered road).

l The vehicle hydroplanes while driving at high speed on the wet or slick

road.

160

2-4. Using other driving systems

CAUTION

n Stopping distance when ABS is operating on the wet or slick roads

ABS is not designed to shorten the vehicle's stopping distance. Always maintain a safe distance from the vehicle in front of you in the following situ- ations. l When driving on dirt, gravel or snow-covered roads l When driving with tire chains l When driving over bumps in the road l When driving over roads with potholes or uneven roads

n TRAC may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the TRAC system is operating. Do not drive the vehicle in conditions where stability and power may be lost.

n When VSC is activated

The slip indicator light flashes and a warning buzzer sounds. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes and a buzzer sounds.

n When TRAC and VSC are off

Be especially careful and drive at a speed appropriate to the road condi- tions. As these are systems to ensure vehicle stability and driving force, do not turn off TRAC and VSC unless necessary.

n Replacing tires

Make sure that all tires are of the same size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the recom- mended tire pressure level. The ABS and VSC system will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.

n Handling of tires and suspension

Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.

161

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load. l Stow cargo and luggage in the trunk whenever possible. Be sure

all items are secured in place.

l Be careful to keep the vehicle level. Placing the weight as far for-

ward as possible helps maintain vehicle balance.

l For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) Steps for Determining Correct Load Limit ⎯ (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehi- cle’s placard.

(2) Determine the combined weight of the driver and passengers

that will be riding in your vehicle.

(3) Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4) The resulting figure equals the available amount of cargo and

luggage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of avail- able cargo and luggage load capacity is 650 lbs. (1400 - 750 (5 × 150) = 650 lbs.)

(5) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

162

2-5. Driving information

(6)

If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 170)

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 825 lb. (370
kg), the available amount of cargo and luggage load capacity will be as follows: 825 lb. - 366 lb. = 459 lb. (370 kg -166 kg = 204 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

459 lb. - 388 lb. = 71 lb. (204 kg - 176 kg = 28 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

163

2-5. Driving information

CAUTION

n Storage precautions

l To prevent cargo and luggage from sliding forward during braking, do not stack anything in the enlarged trunk. Keep cargo and luggage low, as close to the floor as possible.

l Never allow anyone to ride in the enlarged trunk. It is not designed for passengers. They should ride in their seats with their seat belts prop- erly fastened. Otherwise, they are much more likely to suffer death or serious bodily injury, in the event of sudden braking or a collision.

l Do not place anything on the package tray behind the rear seatback. Such items may be thrown about and possibly injure people in the vehicle during sudden braking or in an accident.

l Do not drive with objects on top of the instrument panel.

They may interfere with the driver’s field of view or move during sharp acceleration or turning, thus impairing the driver’s control of the vehi- cle. In an accident they may injure the vehicle occupants.

l Secure all items in the occupant compartment, as they may shift and

injure someone during an accident or sudden braking.

n Capacity and distribution

l Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

l Even if the total load of occupant's weight and the cargo load is less

than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking con- trol which may cause death or serious injury.

164

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. n Total load capacity: 825 lb. (370 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

n Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person.

n Towing capacity: 1500 lb. (680 kg) n Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

n Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 335)

CAUTION

n Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

165

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. n Pre-winter preparations

l Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

l Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

l Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. n Before driving the vehicle

Perform the following according to the driving conditions. l Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. l To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

l Remove any ice that has accumulated on the vehicle chassis. l Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

166

2-5. Driving information

n When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

n When parking the vehicle

Park the vehicle and move the shift lever to P (automatic trans- mission), 1 or R (manual transmission) without setting the park- ing brake. The parking brake may freeze up, preventing it from being released.

Selecting tire chains

Vehicles with 15-inch tires

Use the tire chains of correct size and type.

Use SAE Class “S” type radial tire chains except radial cable chains or V-bar type chains. Vehicles with 16-inch and 17-inch tires

Use the correct tire chain size when mounting the snow chains. Chain size is regulated for each tire size.

Side chain:

0.12 in. (3 mm) in diameter 0.39 in. (10 mm) in width 1.18 in. (30 mm) in length

Cross chain:

0.16 in. (4 mm) in diameter 0.55 in. (14 mm) in width 0.98 in. (25 mm) in length

167

2-5. Driving information

Regulations on the use of snow chains

l Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains. Install the chains on the front tires.

l Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

n Snow chain installation

Observe the following precautions when installing and removing chains.

Install and remove tire chains in a safe location. Install tire chains on the front tires only. Do not install tire chains on rear tires. Install tire chains following the instructions provided in the accompanying manual.

168

2-5. Driving information

CAUTION

n Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. l Use tires of the size specified for your vehicle. l Maintain the recommended level of air pressure. l Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

l Use snow tires on all, not just some wheels.

n Driving with tire chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. l Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

l Avoid driving on bumpy road surfaces or over potholes. l Avoid sudden turns and braking, as use of chains may adversely affect

vehicle handling.

l Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

NOTICE

n Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

n Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

169

2-5. Driving information Trailer towing

Your vehicle is designed primarily as a passenger carrying vehicle. Towing a trailer will have an adverse effect on handling, perfor- mance, braking, durability, and fuel consumption. For your safety and the safety of others, do not overload the vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. n Weight limits

Confirm that the total trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits.

n Gross vehicle weight

The gross vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR) indicated on the Certification Label. The gross vehicle weight is the sum weight of the unloaded vehicle, driver, passengers, luggage, hitch and trailer tongue load. Also included is the weight of any special equipment installed on your vehicle.

n Gross axle weight

The load on either the front or rear axle resulting from distribu- tion of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label.

Certification label

170

2-5. Driving information

n Trailer tongue load

The trailer cargo load should be distributed so that the tongue load is 9 to 11% of the total trailer weight, not exceeding the maximum 150 lb. (68 kg). (Tongue load / Total trailer weight x 100 = 9 to 11%) The total trailer weight and tongue load can be measured with platform scales found at highway weighing stations, building supply companies, trucking companies, junk yards, etc.

Total trailer weight Tongue load

Towing a trailer

Contact your Toyota dealer for further information about additional requirements such as a towing kit, etc.

Hitch

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be rated for towing a higher weight, the operator must never exceed the maxi- mum weight rating specified for the trailer hitch.

171

2-5. Driving information

n Before towing

l Ensure that your vehicle’s tires are properly inflated. (→P. 335) l Trailer tires should be inflated according to the trailer manufacturer's rec-

ommendation.

l All trailer lights must work in order to be legal. l Confirm all lights work each time you connect them. l Check that your vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue load, overloading, worn suspension, or other possible causes.

l Make sure the trailer cargo is securely loaded. l Check that your rear view mirrors conform to any federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes. n Break-in schedule

Toyota recommends that you do not use a new vehicle or a vehicle with any new power train components (engine, transmission, differential, wheel bear- ings, etc.) to tow a trailer for the first 500 miles (800 km) of driving.

n Maintenance

If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner's Manual Supplement”.)

l Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km) of trailer towing.

172

2-5. Driving information

CAUTION

n To avoid accident or injury

l Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue load capacities.

l Never load more weight in the back than in the front of the trailer. About 60% of the load should be in the front half of the trailer, and the remaining 40% in the rear.

n Hitches

l Use only a hitch that conforms to the total trailer weight requirement. l Follow the directions supplied by the hitch manufacturer. l Lubricate the hitch ball with a light coat of grease. l Remove the trailer hitch whenever you are not towing a trailer. After removing the hitch, seal any mounting hole in the vehicle body to prevent entry of any substances into the vehicle.

n When towing a trailer

If the gross trailer weight exceeds 1000 lb. (453 kg), trailer brakes are required. Toyota recommends trailers with brakes that conform to all appli- cable federal and state/provincial regulations.

l Never tap into your vehicle's hydraulic system, as this will lower the vehi-

cle's braking effectiveness.

l Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

173

2-5. Driving information

NOTICE

n When installing a trailer hitch

l Use only the position recommended by your Toyota dealer. Do not install

the trailer hitch on the bumper; this may cause body damage.

l Do not use axle-mounted hitches, as they can cause damage to the axle

housing, wheel bearings, wheels or tires.

n Brakes

Toyota recommends trailers with brakes that conform to all applicable fed- eral and state/provincial regulations.

n Safety chain

A safety chain must always be used between the towing vehicle and the trailer. Leave sufficient slack in the chain for turns. The chain should cross under the trailer tongue to prevent the tongue from dropping to the ground in the case that it becomes damaged or separated. For the correct safety chain installation procedure, ask your Toyota dealer.

n Do not directly splice trailer lights

Directly splicing trailer lights may damage your vehicle's electrical system and cause a malfunction.

Trailer towing tips

Your vehicle will handle differently when towing a trailer. The 3 main causes of vehicle-trailer accidents are driver error, excessive speed and improper trailer loading. Keep the following in mind when towing. l Before starting out, check the trailer lights and the vehicle-trailer

connections. Recheck after driving a short distance.

l Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle.

174

2-5. Driving information

l Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

l As stopping distance is increased when towing a trailer, vehicle-to- vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

l Avoid sudden braking as you may skid, resulting in jackknifing and

loss of control. This is especially true on wet or slippery surfaces.

l Avoid jerky starts or sudden acceleration. l Avoid jerky steering and sharp turns, and slow down before mak-

ing turns.

l Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a larger than normal turning radius.

l Crosswinds and rough roads will adversely affect handling of your vehicle and trailer, causing sway. Periodically check the rear to prepare for being passed by large trucks or buses, which may cause your vehicle and trailer to sway. If swaying occurs, firmly grip the steering wheel, reduce speed immediately but gradually, and steer straight ahead. Never increase speed. If you make no extreme correction with the steering or brakes, your vehicle and trailer will stabilize.

l Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

175

2-5. Driving information

In order to maintain efficient engine braking and electrical charging performance, do not use overdrive (automatic transmission) or the 5th gear (manual transmission).

l Due to the added load of the trailer, your vehicle's engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the engine coolant temperature gauge indicates overheating, immediately turn off the air condition- ing (if in use), pull your vehicle off the road and stop in a safe spot. (→P. 411)

l Always place wheel blocks under both the vehicle and the trailer wheels when parking. Apply the parking brake firmly, and put the transmission in P (automatic transmission) or in 1 or R (manual transmission). Avoid parking on a slope, but if unavoidable, do so only after performing the following:

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5

Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle and trailer wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into 1 or R (manual transmission) or P (automatic trans- mission) and turn off the engine.

l When restarting after parking on a slope: STEP 1

With the transmission in the P position (automatic transmis- sion) or the clutch pedal (manual transmission) depressed, start the engine. On vehicles with an automatic transmission, be sure to keep the brake pedal pressed. Shift into a forward gear. If reversing, shift into the R position. Release the parking brake (also brake pedal on vehicles with an automatic transmission), and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

STEP 2

STEP 3

STEP 4

176

2-5. Driving information

CAUTION

n To avoid an accident

l Do not exceed 45 mph (72 km/h) or posted towing speed limit, whichever is lower. As instability (swaying) of the towing vehicle-trailer combination increases as speed increases, exceeding 45 mph (72 km/h) may cause loss of control.

l Slow down and downshift before descending steep or long downhill

grades. Do not make sudden downshifts.

l Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

177

2-5. Driving information Dinghy towing (automatic transmission)

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

n To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

178

2-5. Driving information Dinghy towing (manual transmission)

Your vehicle can be dinghy towed in a forward direction (with 4
wheels on the ground) behind a motor home.

Towing your vehicle with 4 wheels on the ground

To prevent damage to your vehicle, perform the following procedures before towing. STEP 1

Shift the shift lever to N. Switch to the “ACC” position. (→P. 126) Ensure that the audio system and other powered devices have been turned off. Release the parking brake. After towing, leave the engine in idle for at least 3 minutes before driving the vehicle.

STEP 2

STEP 3

n Necessary equipment and accessories

Specialized equipment and accessories are required for dinghy towing. Con- tact the service branch of the motor home manufacturer regarding recom- mended equipment.

179

2-5. Driving information

NOTICE

n Dinghy towing direction

Do not tow the vehicle backwards. Doing so may cause serious damage.

n To prevent the steering from locking

Ensure the engine switch is in the “ACC” position.

180

2-5. Driving information

181

3-1. Using the air conditioning system and defogger Automatic air conditioning system (if equipped)

Air outlets and fan speed are automatically adjusted according to the temperature setting.

Temperature control

Automatic mode

Windshield defogger

Air intake mode switch

Air conditioning ON/OFF switch

OFF Temperature setting display

Changes the air outlets used

Fan speed

Fan speed display

Air outlet display

Using the automatic mode

STEP 1

Press

The air conditioning system will begin to operate. Press “∧” to increase the temperature and “∨” to decrease the

STEP 2

temperature on

184

3-1. Using the air conditioning system and defogger

Adjusting the settings

n Adjusting the temperature setting

Press “∧” to increase the temperature and “∨” to decrease the tem-

perature on

n Adjusting the fan speed

Press “∧” (increase) or “∨” (decrease) on

The fan speed is shown on the display. (7 levels) Press

to turn the fan off.

n Changing the air outlets

Press

The air outlets switch each time shown on the display indicates the following.

is pressed. The air flow

Air flows to the upper body.

185

3-1. Using the air conditioning system and defogger

Air flows to the upper body and feet.

: Some models

Mainly air flows to the feet.

: Some models

Air flows to the feet and the windshield defogger operates.

Recirculated air mode will auto- matically switch to outside air mode.

: Some models

n Switching air intake modes

Press The mode switches between outside air mode (indicator off) and recircu- lated air mode (indicator on) each time

is pressed.

186

3-1. Using the air conditioning system and defogger

Defogging the windshield

Defogging

The air conditioning system con- trol operates automatically. Recirculated air mode will auto- matically switch to outside air mode. It is not possible to return to recirculated air mode when the switch is on.

Adjusting the position of and opening and closing the air outlets

Center outlets

Direct air flow to the left or right, up or down.

Right and left side outlets

Direct air flow to the left or right, up or down. Turn the knob right to open the vent and left to close the vent.

187

3-1. Using the air conditioning system and defogger

n Using the automatic mode

Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions. As a result, the following may occur. l The system may switch automatically to recirculated air mode when the

coolest temperature setting is selected in summer.

Immediately after warm or cool air is ready to flow.

is pressed, the fan may stop for a while until

l Cool air may flow to the area around the upper body when the heater is

on.

n Using the recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

n Window defogger feature

Recirculated air mode may automatically switch to outside air mode in situa- tions where the windows need to be defogged.

n When outside air temperature approaches 32°F (0°C)

The air conditioning system may not operate even when

is pressed.

n When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the temperature setting.

188

3-1. Using the air conditioning system and defogger

CAUTION

n To prevent the windshield from fogging up

Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.

NOTICE

n To prevent battery discharge

Do not leave the automatic air conditioning system on longer than necessary when the engine is stopped.

189

3-1. Using the air conditioning system and defogger Manual air conditioning system (if equipped)

Heater

Air outlet selection dial

Temperature control dial

Fan speed control dial

Air intake mode switch

Air conditioning system

Air outlet selection dial

Temperature control dial

Fan speed control dial

Air intake mode switch

Air conditioning ON/OFF switch

190

3-1. Using the air conditioning system and defogger

Adjusting the settings

n Adjusting the temperature setting (heater)

Turn the temperature control dial clockwise to increase the temper- ature.

n Adjusting the temperature setting (air conditioning system)

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).

is not pressed, the system will blow ambient temperature air or

If heated air.

n Adjusting the fan speed

Turn the fan speed control dial clockwise (increase) or counter- clockwise (decrease). Set the dial to “0” to turn the fan off.

n Selecting the air outlets

Set the air outlet selection dial to an appropriate position. The positions between the air outlet selections shown below can also be selected for more detailed adjustment.

Air flows to the upper body.

191

3-1. Using the air conditioning system and defogger

Air flows to the upper body and feet.

: Some models

Mainly air flows to the feet.

Air flows to the feet and the windshield defogger operates.

The air intake is automatically switched to outside air mode. It is not possible to return to recircu- lated air mode when the switch is on.

: Some models

: Some models

192

3-1. Using the air conditioning system and defogger

Air flows to the windshield and side windows.

The air intake is automatically switched to outside air mode. It is not possible to return to recircu- lated air mode when the switch is on.

n Switching air intake modes

Press

The mode switches between outside air mode (indicator off) and recircu-

lated air mode (indicator on) each time

is pressed.

193

3-1. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Center outlets

Direct air flow to the left or right, up or down.

Right and left side outlets

Direct air flow to the left or right, up or down. Turn the knob right to open the vent and left to close the vent.

194

3-1. Using the air conditioning system and defogger

n For quick cooling (vehicles with air conditioning system)

Turn the temperature control dial to the “MAX A/C” position and select the recirculated air mode.

n For quick clearing of the windshield and side windows (vehicles with

air conditioning system)

Press

to turn the air conditioning on.

n Using the recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

n When outside air temperature approaches 32°F (0°C) (vehicles with air

conditioning system)

The air conditioning system may not operate even when

is pressed.

n When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the position of the temperature adjust- ment dial.

CAUTION

n To prevent the windshield from fogging up

Do not set the air outlet selection dial to during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.

195

3-1. Using the air conditioning system and defogger

NOTICE

n To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is stopped.

196

3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers

Clear the rear window using the defogger.

Vehicles with automatic air conditioning system

On/off

The defoggers will automati- cally turn off after approxi- mately 15 minutes.

Vehicles with manual air conditioning system

On/off

The defoggers will automati- cally turn off after approxi- mately 15 minutes.

n Outside rear view mirror defoggers (if equipped)

Turning the rear window defogger on will turn the outside rear view mirror defoggers on.

CAUTION

n Outside rear view mirror defoggers (if equipped)

The surfaces of the outside rear view mirrors become hot. Do not touch them to prevent from burning yourself.

197

3-2. Using the audio system Audio system types

With navigation system

Owners of models equipped with a navigation system should refer to the “Navigation System Owner's Manual”.

Without navigation system

Type A: CD player with changer controller and AM/FM radio

Type B: CD player with changer and AM/FM radio

198

3-2. Using the audio system

Title

Using the radio Using the CD player Playing MP3 and WMA discs Optimal use of the audio system Using the AUX adapter Using the steering wheel audio switches

Page P. 201
P. 207
P. 214
P. 221
P. 224
P. 225

n Using cellular phones

Interference may be heard through the audio system's speakers if a cellular phone is being used inside or close to the vehicle while the audio system is operating.

CAUTION

n For vehicles sold in U.S.A. and Canada

l Part 15 of the FCC Rules

FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.

l Laser products

• Do not take this unit apart or attempt to make any changes yourself.

This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disas- semble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.

• This product utilizes a laser.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation expo- sure.

199

3-2. Using the audio system

NOTICE

n To prevent battery discharge

Do not leave the audio system on longer than necessary with the engine off.

n To avoid damaging the audio system

Take care not to spill drinks or other fluids over the audio system.

200

3-2. Using the audio system Using the radio

Power

Volume

Changing the channel

Adjusting the frequency (AM, FM mode) or channel (SAT mode)

Scanning for receivable stations

Seeking the frequency

Station selector

AM⋅SAT/FM mode buttons

Displaying radio text messages

Setting station presets (excluding XM® Satellite Radio)

STEP 1

Search for desired stations by turning

or pressing “∧”

or “∨” on

STEP 2

Press and hold the button (from is to be set to until you hear a beep.

to

) the station

Scanning radio stations (excluding XM® Satellite Radio)

n Scanning the preset radio stations STEP 1

until you hear a beep.

Press and hold Preset stations will be played for 5 seconds each. When the desired station is reached, press again.

STEP 2

once

201

3-2. Using the audio system

n Scanning all radio stations within range STEP 1

Press All stations with reception will be played for 5 seconds each. When the desired station is reached, press again.

STEP 2

XM® Satellite Radio* (if equipped) n Receiving XM® Satellite Radio STEP 1

Press The display changes as follows each time pressed. AM → SAT1 → SAT2 → SAT3

once

is

STEP 2

Turn

to select the desired channel from all categories

or press “∧” or “∨” on the current category.

to select the desired channel in

n Setting XM® Satellite Radio channel presets

Select the desired channel. Press and hold the button (from ) the channel is to be set to until you hear a beep. to

n Changing the channel category

Press “∧” or “∨” on

202

3-2. Using the audio system

n Scanning XM® Satellite Radio channels

l Scanning channels in the current category

STEP 1

STEP 2

Press When the desired channel is reached, press again.

l Scanning preset channels

STEP 1

STEP 2

Press and hold until you hear a beep. When the desired channel is reached, press again.

n Displaying text information

Press The display will show up to 10 characters. The display changes as follows each time the button is pressed. l CH NAME l TITLE (SONG/PROGRAM TITLE) l NAME (ARTIST NAME/FEATURE) l CH NUMBER

*: Except JBL brand audio system⎯

Use of XM® Satellite Radio requires XM® tuner and service. Contact your Toyota dealer.

203